1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
|
conf.sh(3) -- easy loading of configuration files
==============================================
## SYNOPSIS
`. $(librelib conf)`
## DESCRIPTION
`conf.sh` is a Bash(1) library to easily load various configuration
files related to Arch Linux/Parabola(7) and libretools(7).
I recommend reading the source yourself--it is mostly
self-explanatory, and is shorter than this document.
### VARIABLES
When loading configuration files in a program run with `sudo`(8), it
is often desirable to load the configuration files from the home
directory of the user who called `sudo`, instead of from /root.
To accommodate this, instead of using the usual $<USER> and $<HOME>,
`conf.sh` sets $<LIBREUSER> and $<LIBREHOME>, which it then uses.
* <LIBREUSER>:
If $<SUDO_USER> is set, then $<LIBREUSER> is set to
that. Otherwise, $<LIBREUSER> is set to the value of $<USER>.
* <LIBREHOME>:
If $<LIBREUSER> == $<USER>, then $<LIBREHOME> is set to the value
of $<HOME>. Otherwise, it is set to the default home directory
of the user $<LIBREUSER>.
Further, `conf.sh` works with XDG; it sets and uses
$<XDG_CONFIG_HOME> and $<XDG_CACHE_HOME> with the following values:
* <XDG_CONFIG_HOME>:
If it isn't already set, it is set to "$<LIBREHOME>/.config" and
exported.
* <XDG_CACHE_HOME>:
If it isn't already set, it is set to "$<LIBREHOME>/.cache" and
exported.
Note that only the XDG_* variables are exported.
### GENERIC ROUTINES
The following routines take a "slug" to refer to a group of
configuration files; that is the basename of the files. For example,
<SLUG>='abs' will identify `/etc/abs.conf` and `$<LIBREHOME>/.abs.conf`.
The routines you will likely actually use are:
* `load_files` <SLUG>:
Loads the configuration files for <SLUG>, loading the files in
the correct order, and checking the appropriate environmental
variables.
* `check_vars` <SLUG> <VARS>...:
Checks to see if all of <VARS> are defined. If any of them
aren't, it prints a message to configure them in the
configuration files for <SLUG>, and returns with a non-zero
status.
* `get_var` <SLUG> <VAR> <DEFAULT>:
If <VAR> is set in the configuration for <SLUG>, print it's
value, considering environmental variables. If it is not set,
return <DEFAULT>. This does NOT work for array variables.
* `set_var` <SLUG> <VAR> <VALUE>:
Set the variable <VAR> equal to <VALUE> in the configuration file
for <SLUG> of highest precedence that already exists, and is
writable. If no files fit this description, the routine does
nothing and returns a non-zero exit status. This does NOT work
for array variables.
There are two more routines the above routines use internally that are
used internally by . You are unlikely to use them directly, but they
might be useful for debugging, or at least describing behavior.
* `list_files` <SLUG>:
Lists (newline-separated) the configuration files that must be
considered for <SLUG>. Files listed later take precedence over
files listed earlier.
* `list_envvars` <SLUG>:
Lists (newline-separated) the environmental variables that take
precedence over the settings in the configuration files for
<SLUG>. For example, in `makepkg.conf`(8) (<SLUG>=makepkg), if the
<PACKAGER> environmental variable is set, the value in the
configuration file is ignored.
### PKGBUILD ROUTINES
These two routines deal with loading `PKGBUILD`(5) files.
* `unset_PKGBUILD`:
Unsets all variables and functions that might be set in a
`PKGBUILD`(5) file, including those specific to `librefetch`(8).
* `load_PKGBUILD` [<FILE>]:
"Safely" loads a PKGBUILD. Everything that it would normally set
is unset first, $<CARCH> is set according to `makepkg.conf`(5),
then the file is loaded. The file to be loaded is <FILE>, or
"./PKGBUILD" by default. This isn't safe, security wise, in that
the PKGBUILD is free to execute code.
### SLUGS
The differences in behavior for anything that takes a slug comes down
to the differences in the output for `list_files` and `list_envvars`.
The "known" slugs are "abs", "makepkg", and "libretools". If anything
else is given, then:
* `list_files` will give back "/etc/libretools.d/<SLUG>.conf" and
"$<XDG_CONFIG_HOME>/libretools/<SLUG>.conf"
* `list_envvars` will give back an empty list.
The rules for <SLUG>=(abs|makepkg|libretools) are more easily
expressed in code than prose, so it is recommended that you look at
that.
## BUGS
`get_conf_makepkg` and `set_conf_makepkg` do not work with arrays.
## SEE ALSO
librelib(7)
abs.conf(5), makepkg.conf(5), libretools.conf(5), PKGBUILD(5)
chroot.conf(5), librefetch.conf(5)
|
