Linux-libre 4.5-gnu

1 files changed, 0 insertions, 93 deletions

diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
deleted file mode 100644
index 06c88a4d2..000000000
--- a/Documentation/devicetree/bindings/arm/l2cc.txt
+++ /dev/null
@@ -1,93 +0,0 @@
-* ARM L2 Cache Controller
-
-ARM cores often have a separate level 2 cache controller. There are various
-implementations of the L2 cache controller with compatible programming models.
-Some of the properties that are just prefixed "cache-*" are taken from section
-3.7.3 of the ePAPR v1.1 specification which can be found at:
-https://www.power.org/wp-content/uploads/2012/06/Power_ePAPR_APPROVED_v1.1.pdf
-
-The ARM L2 cache representation in the device tree should be done as follows:
-
-Required properties:
-
-- compatible : should be one of:
-  "arm,pl310-cache"
-  "arm,l220-cache"
-  "arm,l210-cache"
-  "bcm,bcm11351-a2-pl310-cache": DEPRECATED by "brcm,bcm11351-a2-pl310-cache"
-  "brcm,bcm11351-a2-pl310-cache": For Broadcom bcm11351 chipset where an
-     offset needs to be added to the address before passing down to the L2
-     cache controller
-  "marvell,aurora-system-cache": Marvell Controller designed to be
-     compatible with the ARM one, with system cache mode (meaning
-     maintenance operations on L1 are broadcasted to the L2 and L2
-     performs the same operation).
-  "marvell,aurora-outer-cache": Marvell Controller designed to be
-     compatible with the ARM one with outer cache mode.
-  "marvell,tauros3-cache": Marvell Tauros3 cache controller, compatible
-     with arm,pl310-cache controller.
-- cache-unified : Specifies the cache is a unified cache.
-- cache-level : Should be set to 2 for a level 2 cache.
-- reg : Physical base address and size of cache controller's memory mapped
-  registers.
-
-Optional properties:
-
-- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
-  read, write and setup latencies. Minimum valid values are 1. Controllers
-  without setup latency control should use a value of 0.
-- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
-  read, write and setup latencies. Controllers without setup latency control
-  should use 0. Controllers without separate read and write Tag RAM latency
-  values should only use the first cell.
-- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
-- arm,filter-ranges : <start length> Starting address and length of window to
-  filter. Addresses in the filter window are directed to the M1 port. Other
-  addresses will go to the M0 port.
-- arm,io-coherent : indicates that the system is operating in an hardware
-  I/O coherent mode. Valid only when the arm,pl310-cache compatible
-  string is used.
-- interrupts : 1 combined interrupt.
-- cache-size : specifies the size in bytes of the cache
-- cache-sets : specifies the number of associativity sets of the cache
-- cache-block-size : specifies the size in bytes of a cache block
-- cache-line-size : specifies the size in bytes of a line in the cache,
-  if this is not specified, the line size is assumed to be equal to the
-  cache block size
-- cache-id-part: cache id part number to be used if it is not present
-  on hardware
-- wt-override: If present then L2 is forced to Write through mode
-- arm,double-linefill : Override double linefill enable setting. Enable if
-  non-zero, disable if zero.
-- arm,double-linefill-incr : Override double linefill on INCR read. Enable
-  if non-zero, disable if zero.
-- arm,double-linefill-wrap : Override double linefill on WRAP read. Enable
-  if non-zero, disable if zero.
-- arm,prefetch-drop : Override prefetch drop enable setting. Enable if non-zero,
-  disable if zero.
-- arm,prefetch-offset : Override prefetch offset value. Valid values are
-  0-7, 15, 23, and 31.
-- arm,shared-override : The default behavior of the pl310 cache controller with
-  respect to the shareable attribute is to transform "normal memory
-  non-cacheable transactions" into "cacheable no allocate" (for reads) or
-  "write through no write allocate" (for writes).
-  On systems where this may cause DMA buffer corruption, this property must be
-  specified to indicate that such transforms are precluded.
-- prefetch-data : Data prefetch. Value: <0> (forcibly disable), <1>
-  (forcibly enable), property absent (retain settings set by firmware)
-- prefetch-instr : Instruction prefetch. Value: <0> (forcibly disable),
-  <1> (forcibly enable), property absent (retain settings set by
-  firmware)
-
-Example:
-
-L2: cache-controller {
-        compatible = "arm,pl310-cache";
-        reg = <0xfff12000 0x1000>;
-        arm,data-latency = <1 1 1>;
-        arm,tag-latency = <2 2 2>;
-        arm,filter-ranges = <0x80000000 0x8000000>;
-        cache-unified;
-        cache-level = <2>;
-	interrupts = <45>;
-};