Linux-libre 4.8.2-gnupck-4.8.2-gnu

4 files changed, 110 insertions, 5 deletions

diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
index 96c25ee01..6532a59c9 100644
--- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
+++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
@@ -1,13 +1,19 @@
-Analog Device ADV7511(W)/13 HDMI Encoders
+Analog Device ADV7511(W)/13/33 HDMI Encoders
 -----------------------------------------
 
-The ADV7511, ADV7511W and ADV7513 are HDMI audio and video transmitters
+The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters
 compatible with HDMI 1.4 and DVI 1.0. They support color space conversion,
-S/PDIF, CEC and HDCP.
+S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while
+the others support RGB interface.
 
 Required properties:
 
-- compatible: Should be one of "adi,adv7511", "adi,adv7511w" or "adi,adv7513"
+- compatible: Should be one of:
+		"adi,adv7511"
+		"adi,adv7511w"
+		"adi,adv7513"
+		"adi,adv7533"
+
 - reg: I2C slave address
 
 The ADV7511 supports a large number of input data formats that differ by their
@@ -32,6 +38,11 @@ The following input format properties are required except in "rgb 1x" and
 - adi,input-justification: The input bit justification ("left", "evenly",
   "right").
 
+The following properties are required for ADV7533:
+
+- adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
+  be one of 1, 2, 3 or 4.
+
 Optional properties:
 
 - interrupts: Specifier for the ADV7511 interrupt
@@ -42,13 +53,18 @@ Optional properties:
 - adi,embedded-sync: The input uses synchronization signals embedded in the
   data stream (similar to BT.656). Defaults to separate H/V synchronization
   signals.
+- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing
+  generator. The chip will rely on the sync signals in the DSI data lanes,
+  rather than generate its own timings for HDMI output.
 
 Required nodes:
 
 The ADV7511 has two video ports. Their connections are modelled using the OF
 graph bindings specified in Documentation/devicetree/bindings/graph.txt.
 
-- Video port 0 for the RGB or YUV input
+- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the
+  remote endpoint phandle should be a reference to a valid mipi_dsi_host device
+  node.
 - Video port 1 for the HDMI output
 
 
diff --git a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
index 4f2ba8c13..4a0f4f768 100644
--- a/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
+++ b/Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
@@ -5,6 +5,7 @@ Required properties for dp-controller:
 		platform specific such as:
 		 * "samsung,exynos5-dp"
 		 * "rockchip,rk3288-dp"
+		 * "rockchip,rk3399-edp"
 	-reg:
 		physical base address of the controller and length
 		of memory mapped region.
diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
new file mode 100644
index 000000000..56a3e68cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
@@ -0,0 +1,35 @@
+sii902x HDMI bridge bindings
+
+Required properties:
+	- compatible: "sil,sii9022"
+	- reg: i2c address of the bridge
+
+Optional properties:
+	- interrupts-extended or interrupt-parent + interrupts: describe
+	  the interrupt line used to inform the host about hotplug events.
+	- reset-gpios: OF device-tree gpio specification for RST_N pin.
+
+Optional subnodes:
+	- video input: this subnode can contain a video input port node
+	  to connect the bridge to a display controller output (See this
+	  documentation [1]).
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+	hdmi-bridge@39 {
+		compatible = "sil,sii9022";
+		reg = <0x39>;
+		reset-gpios = <&pioA 1 0>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in: endpoint {
+					remote-endpoint = <&dc_out>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt
new file mode 100644
index 000000000..e3f6aa6a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358767.txt
@@ -0,0 +1,53 @@
+Toshiba TC358767 eDP bridge bindings
+
+Required properties:
+ - compatible: "toshiba,tc358767"
+ - reg: i2c address of the bridge, 0x68 or 0x0f, depending on bootstrap pins
+ - clock-names: should be "ref"
+ - clocks: OF device-tree clock specification for refclk input. The reference
+   clock rate must be 13 MHz, 19.2 MHz, 26 MHz, or 38.4 MHz.
+
+Optional properties:
+ - shutdown-gpios: OF device-tree gpio specification for SD pin
+                   (active high shutdown input)
+ - reset-gpios: OF device-tree gpio specification for RSTX pin
+                (active low system reset)
+ - ports: the ports node can contain video interface port nodes to connect
+   to a DPI/DSI source and to an eDP/DP sink according to [1][2]:
+    - port@0: DSI input port
+    - port@1: DPI input port
+    - port@2: eDP/DP output port
+
+[1]: Documentation/devicetree/bindings/graph.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+	edp-bridge@68 {
+		compatible = "toshiba,tc358767";
+		reg = <0x68>;
+		shutdown-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+		clock-names = "ref";
+		clocks = <&edp_refclk>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+
+				bridge_in: endpoint {
+					remote-endpoint = <&dpi_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				bridge_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};