Linux-libre 4.3.2-gnu

6 files changed, 257 insertions, 6 deletions

diff --git a/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt b/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
new file mode 100644
index 000000000..47cb1d14b
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
@@ -0,0 +1,61 @@
+Analog Device AXI-DMAC DMA controller
+
+Required properties:
+ - compatible: Must be "adi,axi-dmac-1.00.a".
+ - reg: Specification for the controllers memory mapped register map.
+ - interrupts: Specification for the controllers interrupt.
+ - clocks: Phandle and specifier to the controllers AXI interface clock
+ - #dma-cells: Must be 1.
+
+Required sub-nodes:
+ - adi,channels: This sub-node must contain a sub-node for each DMA channel. For
+   the channel sub-nodes the following bindings apply. They must match the
+   configuration options of the peripheral as it was instantiated.
+
+Required properties for adi,channels sub-node:
+ - #size-cells: Must be 0
+ - #address-cells: Must be 1
+
+Required channel sub-node properties:
+ - reg: Which channel this node refers to.
+ - adi,length-width: Width of the DMA transfer length register.
+ - adi,source-bus-width,
+   adi,destination-bus-width: Width of the source or destination bus in bits.
+ - adi,source-bus-type,
+   adi,destination-bus-type: Type of the source or destination bus. Must be one
+   of the following:
+	0 (AXI_DMAC_TYPE_AXI_MM): Memory mapped AXI interface
+	1 (AXI_DMAC_TYPE_AXI_STREAM): Streaming AXI interface
+	2 (AXI_DMAC_TYPE_AXI_FIFO): FIFO interface
+
+Optional channel properties:
+ - adi,cyclic: Must be set if the channel supports hardware cyclic DMA
+   transfers.
+ - adi,2d: Must be set if the channel supports hardware 2D DMA transfers.
+
+DMA clients connected to the AXI-DMAC DMA controller must use the format
+described in the dma.txt file using a one-cell specifier. The value of the
+specifier refers to the DMA channel index.
+
+Example:
+
+dma: dma@7c420000 {
+	compatible = "adi,axi-dmac-1.00.a";
+	reg = <0x7c420000 0x10000>;
+	interrupts = <0 57 0>;
+	clocks = <&clkc 16>;
+	#dma-cells = <1>;
+
+	adi,channels {
+		#size-cells = <0>;
+		#address-cells = <1>;
+
+		dma-channel@0 {
+			reg = <0>;
+			adi,source-bus-width = <32>;
+			adi,source-bus-type = <ADI_AXI_DMAC_TYPE_MM_AXI>;
+			adi,destination-bus-width = <64>;
+			adi,destination-bus-type = <ADI_AXI_DMAC_TYPE_FIFO>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/dma/arm-pl08x.txt b/Documentation/devicetree/bindings/dma/arm-pl08x.txt
new file mode 100644
index 000000000..8a0097a02
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/arm-pl08x.txt
@@ -0,0 +1,54 @@
+* ARM PrimeCells PL080 and PL081 and derivatives DMA controller
+
+Required properties:
+- compatible: "arm,pl080", "arm,primecell";
+	      "arm,pl081", "arm,primecell";
+- reg: Address range of the PL08x registers
+- interrupt: The PL08x interrupt number
+- clocks: The clock running the IP core clock
+- clock-names: Must contain "apb_pclk"
+- lli-bus-interface-ahb1: if AHB master 1 is eligible for fetching LLIs
+- lli-bus-interface-ahb2: if AHB master 2 is eligible for fetching LLIs
+- mem-bus-interface-ahb1: if AHB master 1 is eligible for fetching memory contents
+- mem-bus-interface-ahb2: if AHB master 2 is eligible for fetching memory contents
+- #dma-cells: must be <2>. First cell should contain the DMA request,
+              second cell should contain either 1 or 2 depending on
+              which AHB master that is used.
+
+Optional properties:
+- dma-channels: contains the total number of DMA channels supported by the DMAC
+- dma-requests: contains the total number of DMA requests supported by the DMAC
+- memcpy-burst-size: the size of the bursts for memcpy: 1, 4, 8, 16, 32
+  64, 128 or 256 bytes are legal values
+- memcpy-bus-width: the bus width used for memcpy: 8, 16 or 32 are legal
+  values
+
+Clients
+Required properties:
+- dmas: List of DMA controller phandle, request channel and AHB master id
+- dma-names: Names of the aforementioned requested channels
+
+Example:
+
+dmac0: dma-controller@10130000 {
+	compatible = "arm,pl080", "arm,primecell";
+	reg = <0x10130000 0x1000>;
+	interrupt-parent = <&vica>;
+	interrupts = <15>;
+	clocks = <&hclkdma0>;
+	clock-names = "apb_pclk";
+	lli-bus-interface-ahb1;
+	lli-bus-interface-ahb2;
+	mem-bus-interface-ahb2;
+	memcpy-burst-size = <256>;
+	memcpy-bus-width = <32>;
+	#dma-cells = <2>;
+};
+
+device@40008000 {
+	...
+	dmas = <&dmac0 0 2
+		&dmac0 1 2>;
+	dma-names = "tx", "rx";
+	...
+};
diff --git a/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt b/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
new file mode 100644
index 000000000..87740adb2
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
@@ -0,0 +1,54 @@
+NXP LPC18xx/43xx DMA MUX (DMA request router)
+
+Required properties:
+- compatible:	"nxp,lpc1850-dmamux"
+- reg:		Memory map for accessing module
+- #dma-cells:	Should be set to <3>.
+		* 1st cell contain the master dma request signal
+		* 2nd cell contain the mux value (0-3) for the peripheral
+		* 3rd cell contain either 1 or 2 depending on the AHB
+		  master used.
+- dma-requests:	Number of DMA requests for the mux
+- dma-masters:	phandle pointing to the DMA controller
+
+The DMA controller node need to have the following poroperties:
+- dma-requests:	Number of DMA requests the controller can handle
+
+Example:
+
+dmac: dma@40002000 {
+	compatible = "nxp,lpc1850-gpdma", "arm,pl080", "arm,primecell";
+	arm,primecell-periphid = <0x00041080>;
+	reg = <0x40002000 0x1000>;
+	interrupts = <2>;
+	clocks = <&ccu1 CLK_CPU_DMA>;
+	clock-names = "apb_pclk";
+	#dma-cells = <2>;
+	dma-channels = <8>;
+	dma-requests = <16>;
+	lli-bus-interface-ahb1;
+	lli-bus-interface-ahb2;
+	mem-bus-interface-ahb1;
+	mem-bus-interface-ahb2;
+	memcpy-burst-size = <256>;
+	memcpy-bus-width = <32>;
+};
+
+dmamux: dma-mux {
+	compatible = "nxp,lpc1850-dmamux";
+	#dma-cells = <3>;
+	dma-requests = <64>;
+	dma-masters = <&dmac>;
+};
+
+uart0: serial@40081000 {
+	compatible = "nxp,lpc1850-uart", "ns16550a";
+	reg = <0x40081000 0x1000>;
+	reg-shift = <2>;
+	interrupts = <24>;
+	clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
+	clock-names = "uartclk", "reg";
+	dmas = <&dmamux 1 1 2
+		&dmamux 2 1 2>;
+	dma-names = "tx", "rx";
+};
diff --git a/Documentation/devicetree/bindings/dma/mv-xor.txt b/Documentation/devicetree/bindings/dma/mv-xor.txt
index cc29c3526..276ef815e 100644
--- a/Documentation/devicetree/bindings/dma/mv-xor.txt
+++ b/Documentation/devicetree/bindings/dma/mv-xor.txt
@@ -12,10 +12,13 @@ XOR engine has. Those sub-nodes have the following required
 properties:
 - interrupts: interrupt of the XOR channel
 
-And the following optional properties:
+The sub-nodes used to contain one or several of the following
+properties, but they are now deprecated:
 - dmacap,memcpy to indicate that the XOR channel is capable of memcpy operations
 - dmacap,memset to indicate that the XOR channel is capable of memset operations
 - dmacap,xor to indicate that the XOR channel is capable of xor operations
+- dmacap,interrupt to indicate that the XOR channel is capable of
+  generating interrupts
 
 Example:
 
@@ -28,13 +31,8 @@ xor@d0060900 {
 
 	xor00 {
 	      interrupts = <51>;
-	      dmacap,memcpy;
-	      dmacap,xor;
 	};
 	xor01 {
 	      interrupts = <52>;
-	      dmacap,memcpy;
-	      dmacap,xor;
-	      dmacap,memset;
 	};
 };
diff --git a/Documentation/devicetree/bindings/dma/sun4i-dma.txt b/Documentation/devicetree/bindings/dma/sun4i-dma.txt
new file mode 100644
index 000000000..f1634a27a
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/sun4i-dma.txt
@@ -0,0 +1,46 @@
+Allwinner A10 DMA Controller
+
+This driver follows the generic DMA bindings defined in dma.txt.
+
+Required properties:
+
+- compatible:	Must be "allwinner,sun4i-a10-dma"
+- reg:		Should contain the registers base address and length
+- interrupts:	Should contain a reference to the interrupt used by this device
+- clocks:	Should contain a reference to the parent AHB clock
+- #dma-cells :	Should be 2, first cell denoting normal or dedicated dma,
+		second cell holding the request line number.
+
+Example:
+	dma: dma-controller@01c02000 {
+		compatible = "allwinner,sun4i-a10-dma";
+		reg = <0x01c02000 0x1000>;
+		interrupts = <27>;
+		clocks = <&ahb_gates 6>;
+		#dma-cells = <2>;
+	};
+
+Clients:
+
+DMA clients connected to the Allwinner A10 DMA controller must use the
+format described in the dma.txt file, using a three-cell specifier for
+each channel: a phandle plus two integer cells.
+The three cells in order are:
+
+1. A phandle pointing to the DMA controller.
+2. Whether it is using normal (0) or dedicated (1) channels
+3. The port ID as specified in the datasheet
+
+Example:
+	spi2: spi@01c17000 {
+		compatible = "allwinner,sun4i-a10-spi";
+		reg = <0x01c17000 0x1000>;
+		interrupts = <0 12 4>;
+		clocks = <&ahb_gates 22>, <&spi2_clk>;
+		clock-names = "ahb", "mod";
+		dmas = <&dma 1 29>, <&dma 1 28>;
+		dma-names = "rx", "tx";
+		status = "disabled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/dma/zxdma.txt b/Documentation/devicetree/bindings/dma/zxdma.txt
new file mode 100644
index 000000000..3207ceb04
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/zxdma.txt
@@ -0,0 +1,38 @@
+* ZTE ZX296702 DMA controller
+
+Required properties:
+- compatible: Should be "zte,zx296702-dma"
+- reg: Should contain DMA registers location and length.
+- interrupts: Should contain one interrupt shared by all channel
+- #dma-cells: see dma.txt, should be 1, para number
+- dma-channels: physical channels supported
+- dma-requests: virtual channels supported, each virtual channel
+		have specific request line
+- clocks: clock required
+
+Example:
+
+Controller:
+	dma: dma-controller@0x09c00000{
+		compatible = "zte,zx296702-dma";
+		reg = <0x09c00000 0x1000>;
+		clocks = <&topclk ZX296702_DMA_ACLK>;
+		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		dma-channels = <24>;
+		dma-requests = <24>;
+	};
+
+Client:
+Use specific request line passing from dmax
+For example, spdif0 tx channel request line is 4
+	spdif0: spdif0@0b004000 {
+		#sound-dai-cells = <0>;
+		compatible = "zte,zx296702-spdif";
+		reg = <0x0b004000 0x1000>;
+		clocks = <&lsp0clk ZX296702_SPDIF0_DIV>;
+		clock-names = "tx";
+		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		dmas = <&dma 4>;
+		dma-names = "tx";
+	}