Initial import

14 files changed, 731 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt b/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt
new file mode 100644
index 000000000..46525ea3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/armada/marvell,dove-lcd.txt
@@ -0,0 +1,30 @@
+Device Tree bindings for Armada DRM CRTC driver
+
+Required properties:
+ - compatible: value should be "marvell,dove-lcd".
+ - reg: base address and size of the LCD controller
+ - interrupts: single interrupt number for the LCD controller
+ - port: video output port with endpoints, as described by graph.txt
+
+Optional properties:
+
+ - clocks: as described by clock-bindings.txt
+ - clock-names: as described by clock-bindings.txt
+	"axiclk" - axi bus clock for pixel clock
+	"plldivider" - pll divider clock for pixel clock
+	"ext_ref_clk0" - external clock 0 for pixel clock
+	"ext_ref_clk1" - external clock 1 for pixel clock
+
+Note: all clocks are optional but at least one must be specified.
+Further clocks may be added in the future according to requirements of
+different SoCs.
+
+Example:
+
+	lcd0: lcd-controller@820000 {
+		compatible = "marvell,dove-lcd";
+		reg = <0x820000 0x1000>;
+		interrupts = <47>;
+		clocks = <&si5351 0>;
+		clock-names = "ext_ref_clk_1";
+	};
diff --git a/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt b/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt
new file mode 100644
index 000000000..ebc1a914b
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/atmel/hlcdc-dc.txt
@@ -0,0 +1,53 @@
+Device-Tree bindings for Atmel's HLCDC (High LCD Controller) DRM driver
+
+The Atmel HLCDC Display Controller is subdevice of the HLCDC MFD device.
+See ../mfd/atmel-hlcdc.txt for more details.
+
+Required properties:
+ - compatible: value should be "atmel,hlcdc-display-controller"
+ - pinctrl-names: the pin control state names. Should contain "default".
+ - pinctrl-0: should contain the default pinctrl states.
+ - #address-cells: should be set to 1.
+ - #size-cells: should be set to 0.
+
+Required children nodes:
+ Children nodes are encoding available output ports and their connections
+ to external devices using the OF graph reprensentation (see ../graph.txt).
+ At least one port node is required.
+
+Example:
+
+	hlcdc: hlcdc@f0030000 {
+		compatible = "atmel,sama5d3-hlcdc";
+		reg = <0xf0030000 0x2000>;
+		interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+		clock-names = "periph_clk","sys_clk", "slow_clk";
+		status = "disabled";
+
+		hlcdc-display-controller {
+			compatible = "atmel,hlcdc-display-controller";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				hlcdc_panel_output: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&panel_input>;
+				};
+			};
+		};
+
+		hlcdc_pwm: hlcdc-pwm {
+			compatible = "atmel,hlcdc-pwm";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_lcd_pwm>;
+			#pwm-cells = <3>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt b/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt
new file mode 100644
index 000000000..a905c1413
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/bridge/dw_hdmi.txt
@@ -0,0 +1,50 @@
+DesignWare HDMI bridge bindings
+
+Required properties:
+- compatible: platform specific such as:
+   * "snps,dw-hdmi-tx"
+   * "fsl,imx6q-hdmi"
+   * "fsl,imx6dl-hdmi"
+   * "rockchip,rk3288-dw-hdmi"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The HDMI interrupt number
+- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks,
+  as described in Documentation/devicetree/bindings/clock/clock-bindings.txt,
+  the clocks are soc specific, the clock-names should be "iahb", "isfr"
+-port@[X]: SoC specific port nodes with endpoint definitions as defined
+   in Documentation/devicetree/bindings/media/video-interfaces.txt,
+   please refer to the SoC specific binding document:
+    * Documentation/devicetree/bindings/drm/imx/hdmi.txt
+    * Documentation/devicetree/bindings/video/dw_hdmi-rockchip.txt
+
+Optional properties
+- reg-io-width: the width of the reg:1,4, default set to 1 if not present
+- ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+- clocks, clock-names: phandle to the HDMI CEC clock, name should be "cec"
+
+Example:
+	hdmi: hdmi@0120000 {
+		compatible = "fsl,imx6q-hdmi";
+		reg = <0x00120000 0x9000>;
+		interrupts = <0 115 0x04>;
+		gpr = <&gpr>;
+		clocks = <&clks 123>, <&clks 124>;
+		clock-names = "iahb", "isfr";
+		ddc-i2c-bus = <&i2c2>;
+
+		port@0 {
+			reg = <0>;
+
+			hdmi_mux_0: endpoint {
+				remote-endpoint = <&ipu1_di0_hdmi>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			hdmi_mux_1: endpoint {
+				remote-endpoint = <&ipu1_di1_hdmi>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/drm/i2c/tda998x.txt b/Documentation/devicetree/bindings/drm/i2c/tda998x.txt
new file mode 100644
index 000000000..e9e4bce40
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/i2c/tda998x.txt
@@ -0,0 +1,29 @@
+Device-Tree bindings for the NXP TDA998x HDMI transmitter
+
+Required properties;
+  - compatible: must be "nxp,tda998x"
+
+  - reg: I2C address
+
+Optional properties:
+  - interrupts: interrupt number and trigger type
+	default: polling
+
+  - pinctrl-0: pin control group to be used for
+	screen plug/unplug interrupt.
+
+  - pinctrl-names: must contain a "default" entry.
+
+  - video-ports: 24 bits value which defines how the video controller
+	output is wired to the TDA998x input - default: <0x230145>
+
+Example:
+
+	tda998x: hdmi-encoder {
+		compatible = "nxp,tda998x";
+		reg = <0x70>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <27 2>;		/* falling edge */
+		pinctrl-0 = <&pmx_camera>;
+		pinctrl-names = "default";
+	};
diff --git a/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt
new file mode 100644
index 000000000..e75f0e549
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/imx/fsl-imx-drm.txt
@@ -0,0 +1,83 @@
+Freescale i.MX DRM master device
+================================
+
+The freescale i.MX DRM master device is a virtual device needed to list all
+IPU or other display interface nodes that comprise the graphics subsystem.
+
+Required properties:
+- compatible: Should be "fsl,imx-display-subsystem"
+- ports: Should contain a list of phandles pointing to display interface ports
+  of IPU devices
+
+example:
+
+display-subsystem {
+	compatible = "fsl,display-subsystem";
+	ports = <&ipu_di0>;
+};
+
+
+Freescale i.MX IPUv3
+====================
+
+Required properties:
+- compatible: Should be "fsl,<chip>-ipu"
+- reg: should be register base and length as documented in the
+  datasheet
+- interrupts: Should contain sync interrupt and error interrupt,
+  in this order.
+- resets: phandle pointing to the system reset controller and
+          reset line index, see reset/fsl,imx-src.txt for details
+Optional properties:
+- port@[0-3]: Port nodes with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+  Ports 0 and 1 should correspond to CSI0 and CSI1,
+  ports 2 and 3 should correspond to DI0 and DI1, respectively.
+
+example:
+
+ipu: ipu@18000000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx53-ipu";
+	reg = <0x18000000 0x080000000>;
+	interrupts = <11 10>;
+	resets = <&src 2>;
+
+	ipu_di0: port@2 {
+		reg = <2>;
+
+		ipu_di0_disp0: endpoint {
+			remote-endpoint = <&display_in>;
+		};
+	};
+};
+
+Parallel display support
+========================
+
+Required properties:
+- compatible: Should be "fsl,imx-parallel-display"
+Optional properties:
+- interface_pix_fmt: How this display is connected to the
+  display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
+  and "lvds666".
+- edid: verbatim EDID data block describing attached display.
+- ddc: phandle describing the i2c bus handling the display data
+  channel
+- port: A port node with endpoint definitions as defined in
+  Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+example:
+
+display@di0 {
+	compatible = "fsl,imx-parallel-display";
+	edid = [edid-data];
+	interface-pix-fmt = "rgb24";
+
+	port {
+		display_in: endpoint {
+			remote-endpoint = <&ipu_di0_disp0>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/drm/imx/hdmi.txt b/Documentation/devicetree/bindings/drm/imx/hdmi.txt
new file mode 100644
index 000000000..1b756cf9a
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/imx/hdmi.txt
@@ -0,0 +1,58 @@
+Device-Tree bindings for HDMI Transmitter
+
+HDMI Transmitter
+================
+
+The HDMI Transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+with accompanying PHY IP.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx6q-hdmi" or "fsl,imx6dl-hdmi".
+ - gpr : should be <&gpr>.
+   The phandle points to the iomuxc-gpr region containing the HDMI
+   multiplexer control register.
+ - clocks, clock-names : phandles to the HDMI iahb and isrf clocks, as described
+   in Documentation/devicetree/bindings/clock/clock-bindings.txt and
+   Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+ - port@[0-4]: Up to four port nodes with endpoint definitions as defined in
+   Documentation/devicetree/bindings/media/video-interfaces.txt,
+   corresponding to the four inputs to the HDMI multiplexer.
+
+Optional properties:
+ - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
+
+example:
+
+	gpr: iomuxc-gpr@020e0000 {
+		/* ... */
+	};
+
+        hdmi: hdmi@0120000 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                compatible = "fsl,imx6q-hdmi";
+                reg = <0x00120000 0x9000>;
+                interrupts = <0 115 0x04>;
+                gpr = <&gpr>;
+                clocks = <&clks 123>, <&clks 124>;
+                clock-names = "iahb", "isfr";
+                ddc-i2c-bus = <&i2c2>;
+
+                port@0 {
+                        reg = <0>;
+
+                        hdmi_mux_0: endpoint {
+                                remote-endpoint = <&ipu1_di0_hdmi>;
+                        };
+                };
+
+                port@1 {
+                        reg = <1>;
+
+                        hdmi_mux_1: endpoint {
+                                remote-endpoint = <&ipu1_di1_hdmi>;
+                        };
+                };
+        };
diff --git a/Documentation/devicetree/bindings/drm/imx/ldb.txt b/Documentation/devicetree/bindings/drm/imx/ldb.txt
new file mode 100644
index 000000000..9a2136643
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/imx/ldb.txt
@@ -0,0 +1,146 @@
+Device-Tree bindings for LVDS Display Bridge (ldb)
+
+LVDS Display Bridge
+===================
+
+The LVDS Display Bridge device tree node contains up to two lvds-channel
+nodes describing each of the two LVDS encoder channels of the bridge.
+
+Required properties:
+ - #address-cells : should be <1>
+ - #size-cells : should be <0>
+ - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb".
+                Both LDB versions are similar, but i.MX6 has an additional
+                multiplexer in the front to select any of the four IPU display
+                interfaces as input for each LVDS channel.
+ - gpr : should be <&gpr> on i.MX53 and i.MX6q.
+         The phandle points to the iomuxc-gpr region containing the LVDS
+         control register.
+- clocks, clock-names : phandles to the LDB divider and selector clocks and to
+                        the display interface selector clocks, as described in
+                        Documentation/devicetree/bindings/clock/clock-bindings.txt
+        The following clocks are expected on i.MX53:
+                "di0_pll" - LDB LVDS channel 0 mux
+                "di1_pll" - LDB LVDS channel 1 mux
+                "di0" - LDB LVDS channel 0 gate
+                "di1" - LDB LVDS channel 1 gate
+                "di0_sel" - IPU1 DI0 mux
+                "di1_sel" - IPU1 DI1 mux
+        On i.MX6q the following additional clocks are needed:
+                "di2_sel" - IPU2 DI0 mux
+                "di3_sel" - IPU2 DI1 mux
+        The needed clock numbers for each are documented in
+        Documentation/devicetree/bindings/clock/imx5-clock.txt, and in
+        Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+
+Optional properties:
+ - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q
+ - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53,
+               not used on i.MX6q
+ - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should
+   be configured - one input will be distributed on both outputs in dual
+   channel mode
+
+LVDS Channel
+============
+
+Each LVDS Channel has to contain either an of graph link to a panel device node
+or a display-timings node that describes the video timings for the connected
+LVDS display as well as the fsl,data-mapping and fsl,data-width properties.
+
+Required properties:
+ - reg : should be <0> or <1>
+ - port: Input and output port nodes with endpoint definitions as defined in
+   Documentation/devicetree/bindings/graph.txt.
+   On i.MX5, the internal two-input-multiplexer is used. Due to hardware
+   limitations, only one input port (port@[0,1]) can be used for each channel
+   (lvds-channel@[0,1], respectively).
+   On i.MX6, there should be four input ports (port@[0-3]) that correspond
+   to the four LVDS multiplexer inputs.
+   A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected
+   to a panel input port. Optionally, the output port can be left out if
+   display-timings are used instead.
+
+Optional properties (required if display-timings are used):
+ - display-timings : A node that describes the display timings as defined in
+   Documentation/devicetree/bindings/video/display-timing.txt.
+ - fsl,data-mapping : should be "spwg" or "jeida"
+                      This describes how the color bits are laid out in the
+                      serialized LVDS signal.
+ - fsl,data-width : should be <18> or <24>
+
+example:
+
+gpr: iomuxc-gpr@53fa8000 {
+	/* ... */
+};
+
+ldb: ldb@53fa8008 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx53-ldb";
+	gpr = <&gpr>;
+	clocks = <&clks IMX5_CLK_LDB_DI0_SEL>,
+		 <&clks IMX5_CLK_LDB_DI1_SEL>,
+		 <&clks IMX5_CLK_IPU_DI0_SEL>,
+		 <&clks IMX5_CLK_IPU_DI1_SEL>,
+		 <&clks IMX5_CLK_LDB_DI0_GATE>,
+		 <&clks IMX5_CLK_LDB_DI1_GATE>;
+	clock-names = "di0_pll", "di1_pll",
+		      "di0_sel", "di1_sel",
+		      "di0", "di1";
+
+	/* Using an of-graph endpoint link to connect the panel */
+	lvds-channel@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			lvds0_in: endpoint {
+				remote-endpoint = <&ipu_di0_lvds0>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	/* Using display-timings and fsl,data-mapping/width instead */
+	lvds-channel@1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+
+		display-timings {
+			/* ... */
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lvds1_in: endpoint {
+				remote-endpoint = <&ipu_di1_lvds1>;
+			};
+		};
+	};
+};
+
+panel: lvds-panel {
+	/* ... */
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&lvds0_out>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/drm/msm/gpu.txt b/Documentation/devicetree/bindings/drm/msm/gpu.txt
new file mode 100644
index 000000000..67d0a58db
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/msm/gpu.txt
@@ -0,0 +1,52 @@
+Qualcomm adreno/snapdragon GPU
+
+Required properties:
+- compatible: "qcom,adreno-3xx"
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt signal from the gpu.
+- clocks: device clocks
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+  * "core_clk"
+  * "iface_clk"
+  * "mem_iface_clk"
+- qcom,chipid: gpu chip-id.  Note this may become optional for future
+  devices if we can reliably read the chipid from hw
+- qcom,gpu-pwrlevels: list of operating points
+  - compatible: "qcom,gpu-pwrlevels"
+  - for each qcom,gpu-pwrlevel:
+    - qcom,gpu-freq: requested gpu clock speed
+    - NOTE: downstream android driver defines additional parameters to
+      configure memory bandwidth scaling per OPP.
+
+Example:
+
+/ {
+	...
+
+	gpu: qcom,kgsl-3d0@4300000 {
+		compatible = "qcom,adreno-3xx";
+		reg = <0x04300000 0x20000>;
+		reg-names = "kgsl_3d0_reg_memory";
+		interrupts = <GIC_SPI 80 0>;
+		interrupt-names = "kgsl_3d0_irq";
+		clock-names =
+		    "core_clk",
+		    "iface_clk",
+		    "mem_iface_clk";
+		clocks =
+		    <&mmcc GFX3D_CLK>,
+		    <&mmcc GFX3D_AHB_CLK>,
+		    <&mmcc MMSS_IMEM_AHB_CLK>;
+		qcom,chipid = <0x03020100>;
+		qcom,gpu-pwrlevels {
+			compatible = "qcom,gpu-pwrlevels";
+			qcom,gpu-pwrlevel@0 {
+				qcom,gpu-freq = <450000000>;
+			};
+			qcom,gpu-pwrlevel@1 {
+				qcom,gpu-freq = <27000000>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/drm/msm/hdmi.txt b/Documentation/devicetree/bindings/drm/msm/hdmi.txt
new file mode 100644
index 000000000..a29a55f3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/msm/hdmi.txt
@@ -0,0 +1,48 @@
+Qualcomm adreno/snapdragon hdmi output
+
+Required properties:
+- compatible: one of the following
+   * "qcom,hdmi-tx-8084"
+   * "qcom,hdmi-tx-8074"
+   * "qcom,hdmi-tx-8660"
+   * "qcom,hdmi-tx-8960"
+- reg: Physical base address and length of the controller's registers
+- reg-names: "core_physical"
+- interrupts: The interrupt signal from the hdmi block.
+- clocks: device clocks
+  See ../clocks/clock-bindings.txt for details.
+- qcom,hdmi-tx-ddc-clk-gpio: ddc clk pin
+- qcom,hdmi-tx-ddc-data-gpio: ddc data pin
+- qcom,hdmi-tx-hpd-gpio: hpd pin
+- core-vdda-supply: phandle to supply regulator
+- hdmi-mux-supply: phandle to mux regulator
+
+Optional properties:
+- qcom,hdmi-tx-mux-en-gpio: hdmi mux enable pin
+- qcom,hdmi-tx-mux-sel-gpio: hdmi mux select pin
+
+Example:
+
+/ {
+	...
+
+	hdmi: qcom,hdmi-tx-8960@4a00000 {
+		compatible = "qcom,hdmi-tx-8960";
+		reg-names = "core_physical";
+		reg = <0x04a00000 0x1000>;
+		interrupts = <GIC_SPI 79 0>;
+		clock-names =
+		    "core_clk",
+		    "master_iface_clk",
+		    "slave_iface_clk";
+		clocks =
+		    <&mmcc HDMI_APP_CLK>,
+		    <&mmcc HDMI_M_AHB_CLK>,
+		    <&mmcc HDMI_S_AHB_CLK>;
+		qcom,hdmi-tx-ddc-clk = <&msmgpio 70 GPIO_ACTIVE_HIGH>;
+		qcom,hdmi-tx-ddc-data = <&msmgpio 71 GPIO_ACTIVE_HIGH>;
+		qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>;
+		core-vdda-supply = <&pm8921_hdmi_mvs>;
+		hdmi-mux-supply = <&ext_3p3v>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/drm/msm/mdp.txt b/Documentation/devicetree/bindings/drm/msm/mdp.txt
new file mode 100644
index 000000000..1a0598e52
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/msm/mdp.txt
@@ -0,0 +1,48 @@
+Qualcomm adreno/snapdragon display controller
+
+Required properties:
+- compatible:
+  * "qcom,mdp" - mdp4
+- reg: Physical base address and length of the controller's registers.
+- interrupts: The interrupt signal from the display controller.
+- connectors: array of phandles for output device(s)
+- clocks: device clocks
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: the following clocks are required:
+  * "core_clk"
+  * "iface_clk"
+  * "lut_clk"
+  * "src_clk"
+  * "hdmi_clk"
+  * "mpd_clk"
+
+Optional properties:
+- gpus: phandle for gpu device
+
+Example:
+
+/ {
+	...
+
+	mdp: qcom,mdp@5100000 {
+		compatible = "qcom,mdp";
+		reg = <0x05100000 0xf0000>;
+		interrupts = <GIC_SPI 75 0>;
+		connectors = <&hdmi>;
+		gpus = <&gpu>;
+		clock-names =
+		    "core_clk",
+		    "iface_clk",
+		    "lut_clk",
+		    "src_clk",
+		    "hdmi_clk",
+		    "mdp_clk";
+		clocks =
+		    <&mmcc MDP_SRC>,
+		    <&mmcc MDP_AHB_CLK>,
+		    <&mmcc MDP_LUT_CLK>,
+		    <&mmcc TV_SRC>,
+		    <&mmcc HDMI_TV_CLK>,
+		    <&mmcc MDP_TV_CLK>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/drm/tilcdc/panel.txt b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt
new file mode 100644
index 000000000..4ab9e2300
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/tilcdc/panel.txt
@@ -0,0 +1,66 @@
+Device-Tree bindings for tilcdc DRM generic panel output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,panel".
+ - panel-info: configuration info to configure LCDC correctly for the panel
+   - ac-bias: AC Bias Pin Frequency
+   - ac-bias-intrpt: AC Bias Pin Transitions per Interrupt
+   - dma-burst-sz: DMA burst size
+   - bpp: Bits per pixel
+   - fdd: FIFO DMA Request Delay
+   - sync-edge: Horizontal and Vertical Sync Edge: 0=rising 1=falling
+   - sync-ctrl: Horizontal and Vertical Sync: Control: 0=ignore
+   - raster-order: Raster Data Order Select: 1=Most-to-least 0=Least-to-most
+   - fifo-th: DMA FIFO threshold
+ - display-timings: typical videomode of lcd panel.  Multiple video modes
+   can be listed if the panel supports multiple timings, but the 'native-mode'
+   should be the preferred/default resolution.  Refer to
+   Documentation/devicetree/bindings/video/display-timing.txt for display
+   timing binding details.
+
+Optional properties:
+- backlight: phandle of the backlight device attached to the panel
+- enable-gpios: GPIO pin to enable or disable the panel
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+   muxing properly for pins that connect to TFP410 device
+
+Example:
+
+	/* Settings for CDTech_S035Q01 / LCD3 cape: */
+	lcd3 {
+		compatible = "ti,tilcdc,panel";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bone_lcd3_cape_lcd_pins>;
+		backlight = <&backlight>;
+		enable-gpios = <&gpio3 19 0>;
+
+		panel-info {
+			ac-bias           = <255>;
+			ac-bias-intrpt    = <0>;
+			dma-burst-sz      = <16>;
+			bpp               = <16>;
+			fdd               = <0x80>;
+			sync-edge         = <0>;
+			sync-ctrl         = <1>;
+			raster-order      = <0>;
+			fifo-th           = <0>;
+		};
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: 320x240 {
+				hactive         = <320>;
+				vactive         = <240>;
+				hback-porch     = <21>;
+				hfront-porch    = <58>;
+				hsync-len       = <47>;
+				vback-porch     = <11>;
+				vfront-porch    = <23>;
+				vsync-len       = <2>;
+				clock-frequency = <8000000>;
+				hsync-active    = <0>;
+				vsync-active    = <0>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/drm/tilcdc/slave.txt b/Documentation/devicetree/bindings/drm/tilcdc/slave.txt
new file mode 100644
index 000000000..3d2c52460
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/tilcdc/slave.txt
@@ -0,0 +1,18 @@
+Device-Tree bindings for tilcdc DRM encoder slave output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,slave".
+ - i2c: the phandle for the i2c device the encoder slave is connected to
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+   muxing properly for pins that connect to TFP410 device
+
+Example:
+
+	hdmi {
+		compatible = "ti,tilcdc,slave";
+		i2c = <&i2c0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+	};
diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt b/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt
new file mode 100644
index 000000000..a58ae7756
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/tilcdc/tfp410.txt
@@ -0,0 +1,21 @@
+Device-Tree bindings for tilcdc DRM TFP410 output driver
+
+Required properties:
+ - compatible: value should be "ti,tilcdc,tfp410".
+ - i2c: the phandle for the i2c device to use for DDC
+
+Recommended properties:
+ - pinctrl-names, pinctrl-0: the pincontrol settings to configure
+   muxing properly for pins that connect to TFP410 device
+ - powerdn-gpio: the powerdown GPIO, pulled low to power down the
+   TFP410 device (for DPMS_OFF)
+
+Example:
+
+	dvicape {
+		compatible = "ti,tilcdc,tfp410";
+		i2c = <&i2c2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bone_dvi_cape_dvi_00A1_pins>;
+		powerdn-gpio = <&gpio2 31 0>;
+	};
diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt
new file mode 100644
index 000000000..fff10da5e
--- /dev/null
+++ b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt
@@ -0,0 +1,29 @@
+Device-Tree bindings for tilcdc DRM driver
+
+Required properties:
+ - compatible: value should be "ti,am33xx-tilcdc".
+ - interrupts: the interrupt number
+ - reg: base address and size of the LCDC device
+
+Recommended properties:
+ - interrupt-parent: the phandle for the interrupt controller that
+   services interrupts for this device.
+ - ti,hwmods: Name of the hwmod associated to the LCDC
+
+Optional properties:
+ - max-bandwidth: The maximum pixels per second that the memory
+   interface / lcd controller combination can sustain
+ - max-width: The maximum horizontal pixel width supported by
+   the lcd controller.
+ - max-pixelclock: The maximum pixel clock that can be supported
+   by the lcd controller in KHz.
+
+Example:
+
+	fb: fb@4830e000 {
+		compatible = "ti,am33xx-tilcdc";
+		reg = <0x4830e000 0x1000>;
+		interrupt-parent = <&intc>;
+		interrupts = <36>;
+		ti,hwmods = "lcdc";
+	};