summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/gpio
diff options
context:
space:
mode:
authorAndré Fabian Silva Delgado <emulatorman@parabola.nu>2015-09-08 01:01:14 -0300
committerAndré Fabian Silva Delgado <emulatorman@parabola.nu>2015-09-08 01:01:14 -0300
commite5fd91f1ef340da553f7a79da9540c3db711c937 (patch)
treeb11842027dc6641da63f4bcc524f8678263304a3 /Documentation/devicetree/bindings/gpio
parent2a9b0348e685a63d97486f6749622b61e9e3292f (diff)
Linux-libre 4.2-gnu
Diffstat (limited to 'Documentation/devicetree/bindings/gpio')
-rw-r--r--Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt65
-rw-r--r--Documentation/devicetree/bindings/gpio/gpio-ath79.txt38
-rw-r--r--Documentation/devicetree/bindings/gpio/gpio-atlas7.txt50
-rw-r--r--Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt21
-rw-r--r--Documentation/devicetree/bindings/gpio/gpio-xlp.txt47
-rw-r--r--Documentation/devicetree/bindings/gpio/gpio-zynq.txt2
-rw-r--r--Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt39
7 files changed, 261 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
new file mode 100644
index 000000000..435f1bcca
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
@@ -0,0 +1,65 @@
+Broadcom STB "UPG GIO" GPIO controller
+
+The controller's registers are organized as sets of eight 32-bit
+registers with each set controlling a bank of up to 32 pins. A single
+interrupt is shared for all of the banks handled by the controller.
+
+Required properties:
+
+- compatible:
+ Must be "brcm,brcmstb-gpio"
+
+- reg:
+ Define the base and range of the I/O address space containing
+ the brcmstb GPIO controller registers
+
+- #gpio-cells:
+ Should be <2>. The first cell is the pin number (within the controller's
+ pin space), and the second is used for the following:
+ bit[0]: polarity (0 for active-high, 1 for active-low)
+
+- gpio-controller:
+ Specifies that the node is a GPIO controller.
+
+- brcm,gpio-bank-widths:
+ Number of GPIO lines for each bank. Number of elements must
+ correspond to number of banks suggested by the 'reg' property.
+
+Optional properties:
+
+- interrupts:
+ The interrupt shared by all GPIO lines for this controller.
+
+- interrupt-parent:
+ phandle of the parent interrupt controller
+
+- #interrupt-cells:
+ Should be <2>. The first cell is the GPIO number, the second should specify
+ flags. The following subset of flags is supported:
+ - bits[3:0] trigger type and level flags
+ 1 = low-to-high edge triggered
+ 2 = high-to-low edge triggered
+ 4 = active high level-sensitive
+ 8 = active low level-sensitive
+ Valid combinations are 1, 2, 3, 4, 8.
+ See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+- interrupt-controller:
+ Marks the device node as an interrupt controller
+
+- interrupt-names:
+ The name of the IRQ resource used by this controller
+
+Example:
+ upg_gio: gpio@f040a700 {
+ #gpio-cells = <0x2>;
+ #interrupt-cells = <0x2>;
+ compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
+ gpio-controller;
+ interrupt-controller;
+ reg = <0xf040a700 0x80>;
+ interrupt-parent = <0xf>;
+ interrupts = <0x6>;
+ interrupt-names = "upg_gio";
+ brcm,gpio-bank-widths = <0x20 0x20 0x20 0x18>;
+ };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-ath79.txt b/Documentation/devicetree/bindings/gpio/gpio-ath79.txt
new file mode 100644
index 000000000..c52285101
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-ath79.txt
@@ -0,0 +1,38 @@
+Binding for Qualcomm Atheros AR7xxx/AR9xxx GPIO controller
+
+Required properties:
+- compatible: has to be "qca,<soctype>-gpio" and one of the following
+ fallbacks:
+ - "qca,ar7100-gpio"
+ - "qca,ar9340-gpio"
+- reg: Base address and size of the controllers memory area
+- gpio-controller : Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two. The first cell is the pin number and the
+ second cell is used to specify optional parameters.
+- ngpios: Should be set to the number of GPIOs available on the SoC.
+
+Optional properties:
+- interrupt-parent: phandle of the parent interrupt controller.
+- interrupts: Interrupt specifier for the controllers interrupt.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode interrupt
+ source, should be 2
+
+Please refer to interrupts.txt in this directory for details of the common
+Interrupt Controllers bindings used by client devices.
+
+Example:
+
+ gpio@18040000 {
+ compatible = "qca,ar9132-gpio", "qca,ar7100-gpio";
+ reg = <0x18040000 0x30>;
+ interrupts = <2>;
+
+ ngpios = <22>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-atlas7.txt b/Documentation/devicetree/bindings/gpio/gpio-atlas7.txt
new file mode 100644
index 000000000..d7e123fc9
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-atlas7.txt
@@ -0,0 +1,50 @@
+CSR SiRFatlas7 GPIO controller bindings
+
+Required properties:
+- compatible : "sirf,atlas7-gpio"
+- reg : Address range of the pinctrl registers
+- interrupts : Interrupts used by every GPIO group
+- gpio-banks : How many gpio banks on this controller
+- gpio-controller : Indicates this device is a GPIO controller
+- interrupt-controller : Marks the device node as an interrupt controller
+
+The GPIO controller also acts as an interrupt controller. It uses the default
+two cells specifier as described in Documentation/devicetree/bindings/
+interrupt-controller/interrupts.txt.
+
+Example:
+
+ gpio_0: gpio_mediam@17040000 {
+ compatible = "sirf,atlas7-gpio";
+ reg = <0x17040000 0x1000>;
+ interrupts = <0 13 0>, <0 14 0>;
+
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+
+ gpio-controller;
+ interrupt-controller;
+
+ gpio-banks = <2>;
+ gpio-ranges = <&pinctrl 0 0 0>,
+ <&pinctrl 32 0 0>;
+ gpio-ranges-group-names = "lvds_gpio_grp",
+ "uart_nand_gpio_grp";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led1 {
+ gpios = <&gpio_1 15 0>;
+ ...
+ };
+
+ led2 {
+ gpios = <&gpio_2 34 0>;
+ ...
+ };
+ };
+
+Please refer to gpio.txt in this directory for details of the common
+gpio properties used by devices.
diff --git a/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt b/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt
new file mode 100644
index 000000000..abf4db736
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt
@@ -0,0 +1,21 @@
+Axis ETRAX FS General I/O controller bindings
+
+Required properties:
+
+- compatible:
+ - "axis,etraxfs-gio"
+- reg: Physical base address and length of the controller's registers.
+- #gpio-cells: Should be 3
+ - The first cell is the gpio offset number.
+ - The second cell is reserved and is currently unused.
+ - The third cell is the port number (hex).
+- gpio-controller: Marks the device node as a GPIO controller.
+
+Example:
+
+ gio: gpio@b001a000 {
+ compatible = "axis,etraxfs-gio";
+ reg = <0xb001a000 0x1000>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
new file mode 100644
index 000000000..262ee4ddf
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
@@ -0,0 +1,47 @@
+Netlogic XLP Family GPIO
+========================
+
+This GPIO driver is used for following Netlogic XLP SoCs:
+ XLP832, XLP316, XLP208, XLP980, XLP532
+
+Required properties:
+-------------------
+
+- compatible: Should be one of the following:
+ - "netlogic,xlp832-gpio": For Netlogic XLP832
+ - "netlogic,xlp316-gpio": For Netlogic XLP316
+ - "netlogic,xlp208-gpio": For Netlogic XLP208
+ - "netlogic,xlp980-gpio": For Netlogic XLP980
+ - "netlogic,xlp532-gpio": For Netlogic XLP532
+- reg: Physical base address and length of the controller's registers.
+- #gpio-cells: Should be two. The first cell is the pin number and the second
+ cell is used to specify optional parameters (currently unused).
+- gpio-controller: Marks the device node as a GPIO controller.
+- nr-gpios: Number of GPIO pins supported by the controller.
+- interrupt-cells: Should be two. The first cell is the GPIO Number. The
+ second cell is used to specify flags. The following subset of flags is
+ supported:
+ - trigger type:
+ 1 = low to high edge triggered.
+ 2 = high to low edge triggered.
+ 4 = active high level-sensitive.
+ 8 = active low level-sensitive.
+- interrupts: Interrupt number for this device.
+- interrupt-parent: phandle of the parent interrupt controller.
+- interrupt-controller: Identifies the node as an interrupt controller.
+
+Example:
+
+ gpio: xlp_gpio@34000 {
+ compatible = "netlogic,xlp316-gpio";
+ reg = <0 0x34100 0x1000
+ 0 0x35100 0x1000>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ nr-gpios = <57>;
+
+ #interrupt-cells = <2>;
+ interrupt-parent = <&pic>;
+ interrupts = <39>;
+ interrupt-controller;
+ };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
index 986371a4b..db4c6a663 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
@@ -6,7 +6,7 @@ Required properties:
- First cell is the GPIO line number
- Second cell is used to specify optional
parameters (unused)
-- compatible : Should be "xlnx,zynq-gpio-1.0"
+- compatible : Should be "xlnx,zynq-gpio-1.0" or "xlnx,zynqmp-gpio-1.0"
- clocks : Clock specifier (see clock bindings for details)
- gpio-controller : Marks the device node as a GPIO controller.
- interrupts : Interrupt specifier (see interrupt bindings for
diff --git a/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt b/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt
new file mode 100644
index 000000000..eb7cdd69e
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt
@@ -0,0 +1,39 @@
+NXP LPC18xx/43xx GPIO controller Device Tree Bindings
+-----------------------------------------------------
+
+Required properties:
+- compatible : Should be "nxp,lpc1850-gpio"
+- reg : Address and length of the register set for the device
+- clocks : Clock specifier (see clock bindings for details)
+- gpio-controller : Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two
+ - First cell is the GPIO line number
+ - Second cell is used to specify polarity
+
+Optional properties:
+- gpio-ranges : Mapping between GPIO and pinctrl
+
+Example:
+#define LPC_GPIO(port, pin) (port * 32 + pin)
+#define LPC_PIN(port, pin) (0x##port * 32 + pin)
+
+gpio: gpio@400f4000 {
+ compatible = "nxp,lpc1850-gpio";
+ reg = <0x400f4000 0x4000>;
+ clocks = <&ccu1 CLK_CPU_GPIO>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl LPC_GPIO(0,0) LPC_PIN(0,0) 2>,
+ ...
+ <&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5) 7>;
+};
+
+gpio_joystick {
+ compatible = "gpio-keys-polled";
+ ...
+
+ button@0 {
+ ...
+ gpios = <&gpio LPC_GPIO(4,8) GPIO_ACTIVE_LOW>;
+ };
+};