Initial import

8 files changed, 302 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/hwmon/ads1015.txt b/Documentation/devicetree/bindings/hwmon/ads1015.txt
new file mode 100644
index 000000000..918a507d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/ads1015.txt
@@ -0,0 +1,73 @@
+ADS1015 (I2C)
+
+This device is a 12-bit A-D converter with 4 inputs.
+
+The inputs can be used single ended or in certain differential combinations.
+
+For configuration all possible combinations are mapped to 8 channels:
+  0: Voltage over AIN0 and AIN1.
+  1: Voltage over AIN0 and AIN3.
+  2: Voltage over AIN1 and AIN3.
+  3: Voltage over AIN2 and AIN3.
+  4: Voltage over AIN0 and GND.
+  5: Voltage over AIN1 and GND.
+  6: Voltage over AIN2 and GND.
+  7: Voltage over AIN3 and GND.
+
+Each channel can be configured individually:
+ - pga is the programmable gain amplifier (values are full scale)
+    0: +/- 6.144 V
+    1: +/- 4.096 V
+    2: +/- 2.048 V (default)
+    3: +/- 1.024 V
+    4: +/- 0.512 V
+    5: +/- 0.256 V
+ - data_rate in samples per second
+    0: 128
+    1: 250
+    2: 490
+    3: 920
+    4: 1600 (default)
+    5: 2400
+    6: 3300
+
+1) The /ads1015 node
+
+  Required properties:
+
+   - compatible : must be "ti,ads1015"
+   - reg : I2C bus address of the device
+   - #address-cells : must be <1>
+   - #size-cells : must be <0>
+
+  The node contains child nodes for each channel that the platform uses.
+
+  Example ADS1015 node:
+
+    ads1015@49 {
+	    compatible = "ti,ads1015";
+	    reg = <0x49>;
+	    #address-cells = <1>;
+	    #size-cells = <0>;
+
+	    [ child node definitions... ]
+    }
+
+2) channel nodes
+
+  Required properties:
+
+   - reg : the channel number
+
+  Optional properties:
+
+   - ti,gain : the programmable gain amplifier setting
+   - ti,datarate : the converter data rate
+
+  Example ADS1015 channel node:
+
+    channel@4 {
+	    reg = <4>;
+	    ti,gain = <3>;
+	    ti,datarate = <5>;
+    };
diff --git a/Documentation/devicetree/bindings/hwmon/g762.txt b/Documentation/devicetree/bindings/hwmon/g762.txt
new file mode 100644
index 000000000..25cc6d8ee
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/g762.txt
@@ -0,0 +1,47 @@
+GMT G762/G763 PWM Fan controller
+
+Required node properties:
+
+ - "compatible": must be either "gmt,g762" or "gmt,g763"
+ - "reg": I2C bus address of the device
+ - "clocks": a fixed clock providing input clock frequency
+	     on CLK pin of the chip.
+
+Optional properties:
+
+ - "fan_startv": fan startup voltage. Accepted values are 0, 1, 2 and 3.
+	       The higher the more.
+
+ - "pwm_polarity": pwm polarity. Accepted values are 0 (positive duty)
+	       and 1 (negative duty).
+
+ - "fan_gear_mode": fan gear mode. Supported values are 0, 1 and 2.
+
+If an optional property is not set in .dts file, then current value is kept
+unmodified (e.g. u-boot installed value).
+
+Additional information on operational parameters for the device is available
+in Documentation/hwmon/g762. A detailed datasheet for the device is available
+at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf.
+
+Example g762 node:
+
+   clocks {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	g762_clk: fixedclk {
+		 compatible = "fixed-clock";
+		 #clock-cells = <0>;
+		 clock-frequency = <8192>;
+	}
+   }
+
+   g762: g762@3e {
+	compatible = "gmt,g762";
+	reg = <0x3e>;
+	clocks = <&g762_clk>
+	fan_gear_mode = <0>; /* chip default */
+	fan_startv = <1>;    /* chip default */
+	pwm_polarity = <0>;  /* chip default */
+   };
diff --git a/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt b/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt
new file mode 100644
index 000000000..f93242be6
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/ibmpowernv.txt
@@ -0,0 +1,23 @@
+IBM POWERNV platform sensors
+----------------------------
+
+Required node properties:
+- compatible: must be one of
+		"ibm,opal-sensor-cooling-fan"
+		"ibm,opal-sensor-amb-temp"
+		"ibm,opal-sensor-power-supply"
+		"ibm,opal-sensor-power"
+- sensor-id: an opaque id provided by the firmware to the kernel, identifies a
+	     given sensor and its attribute data
+
+Example sensors node:
+
+cooling-fan#8-data {
+	sensor-id = <0x7052107>;
+	compatible = "ibm,opal-sensor-cooling-fan";
+};
+
+amb-temp#1-thrs {
+	sensor-id = <0x5096000>;
+	compatible = "ibm,opal-sensor-amb-temp";
+};
diff --git a/Documentation/devicetree/bindings/hwmon/lm90.txt b/Documentation/devicetree/bindings/hwmon/lm90.txt
new file mode 100644
index 000000000..e8632486b
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/lm90.txt
@@ -0,0 +1,44 @@
+* LM90 series thermometer.
+
+Required node properties:
+- compatible: manufacturer and chip name, one of
+		"adi,adm1032"
+		"adi,adt7461"
+		"adi,adt7461a"
+		"gmt,g781"
+		"national,lm90"
+		"national,lm86"
+		"national,lm89"
+		"national,lm99"
+		"dallas,max6646"
+		"dallas,max6647"
+		"dallas,max6649"
+		"dallas,max6657"
+		"dallas,max6658"
+		"dallas,max6659"
+		"dallas,max6680"
+		"dallas,max6681"
+		"dallas,max6695"
+		"dallas,max6696"
+		"onnn,nct1008"
+		"winbond,w83l771"
+		"nxp,sa56004"
+
+- reg: I2C bus address of the device
+
+- vcc-supply: vcc regulator for the supply voltage.
+
+Optional properties:
+- interrupts: Contains a single interrupt specifier which describes the
+              LM90 "-ALERT" pin output.
+              See interrupt-controller/interrupts.txt for the format.
+
+Example LM90 node:
+
+temp-sensor {
+	compatible = "onnn,nct1008";
+	reg = <0x4c>;
+	vcc-supply = <&palmas_ldo6_reg>;
+	interrupt-parent = <&gpio>;
+	interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_LOW>;
+}
diff --git a/Documentation/devicetree/bindings/hwmon/ltc2978.txt b/Documentation/devicetree/bindings/hwmon/ltc2978.txt
new file mode 100644
index 000000000..ed2f09dc2
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/ltc2978.txt
@@ -0,0 +1,39 @@
+ltc2978
+
+Required properties:
+- compatible: should contain one of:
+  * "lltc,ltc2974"
+  * "lltc,ltc2977"
+  * "lltc,ltc2978"
+  * "lltc,ltc3880"
+  * "lltc,ltc3883"
+  * "lltc,ltm4676"
+- reg: I2C slave address
+
+Optional properties:
+- regulators: A node that houses a sub-node for each regulator controlled by
+  the device. Each sub-node is identified using the node's name, with valid
+  values listed below. The content of each sub-node is defined by the
+  standard binding for regulators; see regulator.txt.
+
+Valid names of regulators depend on number of supplies supported per device:
+  * ltc2974 : vout0 - vout3
+  * ltc2977 : vout0 - vout7
+  * ltc2978 : vout0 - vout7
+  * ltc3880 : vout0 - vout1
+  * ltc3883 : vout0
+  * ltm4676 : vout0 - vout1
+
+Example:
+ltc2978@5e {
+	compatible = "lltc,ltc2978";
+	reg = <0x5e>;
+	regulators {
+		vout0 {
+			regulator-name = "FPGA-2.5V";
+		};
+		vout2 {
+			regulator-name = "FPGA-1.5V";
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt
new file mode 100644
index 000000000..fcca8e744
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt
@@ -0,0 +1,41 @@
+NTC Thermistor hwmon sensors
+-------------------------------
+
+Requires node properties:
+- "compatible" value : one of
+	"epcos,b57330v2103"
+	"murata,ncp15wb473"
+	"murata,ncp18wb473"
+	"murata,ncp21wb473"
+	"murata,ncp03wb473"
+	"murata,ncp15wl333"
+
+/* Usage of vendor name "ntc" is deprecated */
+<DEPRECATED>	"ntc,ncp15wb473"
+<DEPRECATED>	"ntc,ncp18wb473"
+<DEPRECATED>	"ntc,ncp21wb473"
+<DEPRECATED>	"ntc,ncp03wb473"
+<DEPRECATED>	"ntc,ncp15wl333"
+
+- "pullup-uv"	Pull up voltage in micro volts
+- "pullup-ohm"	Pull up resistor value in ohms
+- "pulldown-ohm" Pull down resistor value in ohms
+- "connected-positive" Always ON, If not specified.
+		Status change is possible.
+- "io-channels"	Channel node of ADC to be used for
+		conversion.
+
+Optional node properties:
+- "#thermal-sensor-cells" Used to expose itself to thermal fw.
+
+Read more about iio bindings at
+	Documentation/devicetree/bindings/iio/iio-bindings.txt
+
+Example:
+	ncp15wb473@0 {
+		compatible = "murata,ncp15wb473";
+		pullup-uv = <1800000>;
+		pullup-ohm = <47000>;
+		pulldown-ohm = <0>;
+		io-channels = <&adc 3>;
+	};
diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt
new file mode 100644
index 000000000..610757ce4
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt
@@ -0,0 +1,12 @@
+Bindings for a fan connected to the PWM lines
+
+Required properties:
+- compatible	: "pwm-fan"
+- pwms		: the PWM that is used to control the PWM fan
+
+Example:
+	pwm-fan {
+		compatible = "pwm-fan";
+		status = "okay";
+		pwms = <&pwm 0 10000 0>;
+	};
diff --git a/Documentation/devicetree/bindings/hwmon/vexpress.txt b/Documentation/devicetree/bindings/hwmon/vexpress.txt
new file mode 100644
index 000000000..9c27ed694
--- /dev/null
+++ b/Documentation/devicetree/bindings/hwmon/vexpress.txt
@@ -0,0 +1,23 @@
+Versatile Express hwmon sensors
+-------------------------------
+
+Requires node properties:
+- "compatible" value : one of
+	"arm,vexpress-volt"
+	"arm,vexpress-amp"
+	"arm,vexpress-temp"
+	"arm,vexpress-power"
+	"arm,vexpress-energy"
+- "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg
+  (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt
+  for more details)
+
+Optional node properties:
+- label : string describing the monitored value
+
+Example:
+	energy@0 {
+		compatible = "arm,vexpress-energy";
+		arm,vexpress-sysreg,func = <13 0>;
+		label = "A15 Jcore";
+	};