Linux-libre 4.3.2-gnu

10 files changed, 181 insertions, 123 deletions

diff --git a/Documentation/devicetree/bindings/i2c/i2c-cadence.txt b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt
index 7cb0b5608..ebaa90c58 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-cadence.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt
@@ -2,7 +2,11 @@ Binding for the Cadence I2C controller
 
 Required properties:
   - reg: Physical base address and size of the controller's register area.
-  - compatible: Compatibility string. Must be 'cdns,i2c-r1p10'.
+  - compatible: Should contain one of:
+		* "cdns,i2c-r1p10"
+		Note:	Use this when cadence i2c controller version 1.0 is used.
+		* "cdns,i2c-r1p14"
+		Note:	Use this when cadence i2c controller version 1.4 is used.
   - clocks: Input clock specifier. Refer to common clock bindings.
   - interrupts: Interrupt specifier. Refer to interrupt bindings.
   - #address-cells: Should be 1.
diff --git a/Documentation/devicetree/bindings/i2c/i2c-emev2.txt b/Documentation/devicetree/bindings/i2c/i2c-emev2.txt
new file mode 100644
index 000000000..5ed1ea1c7
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-emev2.txt
@@ -0,0 +1,22 @@
+Device tree configuration for Renesas EMEV2 IIC controller
+
+Required properties:
+- compatible      : "renesas,iic-emev2"
+- reg             : address start and address range size of device
+- interrupts      : specifier for the IIC controller interrupt
+- clocks          : phandle to the IP core SCLK
+- clock-names     : must be "sclk"
+- #address-cells  : should be <1>
+- #size-cells     : should be <0>
+
+Example:
+
+	iic0: i2c@e0070000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,iic-emev2";
+		reg = <0xe0070000 0x28>;
+		interrupts = <0 32 IRQ_TYPE_EDGE_RISING>;
+		clocks = <&iic0_sclk>;
+		clock-names = "sclk";
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-lpc2k.txt b/Documentation/devicetree/bindings/i2c/i2c-lpc2k.txt
new file mode 100644
index 000000000..4101aa621
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-lpc2k.txt
@@ -0,0 +1,33 @@
+NXP I2C controller for LPC2xxx/178x/18xx/43xx
+
+Required properties:
+ - compatible: must be "nxp,lpc1788-i2c"
+ - reg: physical address and length of the device registers
+ - interrupts: a single interrupt specifier
+ - clocks: clock for the device
+ - #address-cells: should be <1>
+ - #size-cells: should be <0>
+
+Optional properties:
+- clock-frequency: the desired I2C bus clock frequency in Hz; in
+  absence of this property the default value is used (100 kHz).
+
+Example:
+i2c0: i2c@400a1000 {
+	compatible = "nxp,lpc1788-i2c";
+	reg = <0x400a1000 0x1000>;
+	interrupts = <18>;
+	clocks = <&ccu1 CLK_APB1_I2C0>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+
+	lm75@48 {
+		compatible = "nxp,lm75";
+		reg = <0x48>;
+	};
+};
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt
new file mode 100644
index 000000000..688783fbe
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt
@@ -0,0 +1,74 @@
+Register-based I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses a single register
+to route the I2C signals.
+
+Required properties:
+- compatible: i2c-mux-reg
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+* Standard I2C mux properties. See mux.txt in this directory.
+* I2C child bus nodes. See mux.txt in this directory.
+
+Optional properties:
+- reg: this pair of <offset size> specifies the register to control the mux.
+  The <offset size> depends on its parent node. It can be any memory-mapped
+  address. The size must be either 1, 2, or 4 bytes. If reg is omitted, the
+  resource of this device will be used.
+- little-endian: The existence indicates the register is in little endian.
+- big-endian: The existence indicates the register is in big endian.
+  If both little-endian and big-endian are omitted, the endianness of the
+  CPU will be used.
+- write-only: The existence indicates the register is write-only.
+- idle-state: value to set the muxer to when idle. When no value is
+  given, it defaults to the last value used.
+
+Whenever an access is made to a device on a child bus, the value set
+in the revelant node's reg property will be output to the register.
+
+If an idle state is defined, using the idle-state (optional) property,
+whenever an access is not being made to a device on a child bus, the
+register will be set according to the idle value.
+
+If an idle state is not defined, the most recently used value will be
+left programmed into the register.
+
+Example of a mux on PCIe card, the host is a powerpc SoC (big endian):
+
+	i2c-mux {
+		/* the <offset size> depends on the address translation
+		 * of the parent device. If omitted, device resource
+		 * will be used instead. The size is to determine
+		 * whether iowrite32, iowrite16, or iowrite8 will be used.
+		 */
+		reg = <0x6028 0x4>;
+		little-endian;		/* little endian register on PCIe */
+		compatible = "i2c-mux-reg";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c1>;
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			si5338: clock-generator@70 {
+				compatible = "silabs,si5338";
+				reg = <0x70>;
+				/* other stuff */
+			};
+		};
+
+		i2c@1 {
+			/* data is written using iowrite32 */
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			si5338: clock-generator@70 {
+				compatible = "silabs,si5338";
+				reg = <0x70>;
+				/* other stuff */
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt
new file mode 100644
index 000000000..8a99150ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c.txt
@@ -0,0 +1,45 @@
+Generic device tree bindings for I2C busses
+===========================================
+
+This document describes generic bindings which can be used to describe I2C
+busses in a device tree.
+
+Required properties
+-------------------
+
+- #address-cells  - should be <1>. Read more about addresses below.
+- #size-cells     - should be <0>.
+- compatible      - name of I2C bus controller following generic names
+		    recommended practice.
+
+For other required properties e.g. to describe register sets,
+clocks, etc. check the binding documentation of the specific driver.
+
+The cells properties above define that an address of children of an I2C bus
+are described by a single value. This is usually a 7 bit address. However,
+flags can be attached to the address. I2C_TEN_BIT_ADDRESS is used to mark a 10
+bit address. It is needed to avoid the ambiguity between e.g. a 7 bit address
+of 0x50 and a 10 bit address of 0x050 which, in theory, can be on the same bus.
+Another flag is I2C_OWN_SLAVE_ADDRESS to mark addresses on which we listen to
+be devices ourselves.
+
+Optional properties
+-------------------
+
+These properties may not be supported by all drivers. However, if a driver
+wants to support one of the below features, it should adapt the bindings below.
+
+- clock-frequency	- frequency of bus clock in Hz.
+- wakeup-source		- device can be used as a wakeup source.
+
+- interrupts		- interrupts used by the device.
+- interrupt-names	- "irq" and "wakeup" names are recognized by I2C core,
+			  other names are left to individual drivers.
+
+Binding may contain optional "interrupts" property, describing interrupts
+used by the device. I2C core will assign "irq" interrupt (or the very first
+interrupt if not using interrupt names) as primary interrupt for the slave.
+
+Also, if device is marked as a wakeup source, I2C core will set up "wakeup"
+interrupt for the device. If "wakeup" interrupt name is not present in the
+binding, then primary interrupt will be used as wakeup interrupt.
diff --git a/Documentation/devicetree/bindings/i2c/ina209.txt b/Documentation/devicetree/bindings/i2c/ina209.txt
deleted file mode 100644
index 9dd2bee80..000000000
--- a/Documentation/devicetree/bindings/i2c/ina209.txt
+++ /dev/null
@@ -1,18 +0,0 @@
-ina209 properties
-
-Required properties:
-- compatible: Must be "ti,ina209"
-- reg: I2C address
-
-Optional properties:
-
-- shunt-resistor
-	Shunt resistor value in micro-Ohm
-
-Example:
-
-temp-sensor@4c {
-	compatible = "ti,ina209";
-	reg = <0x4c>;
-	shunt-resistor = <5000>;
-};
diff --git a/Documentation/devicetree/bindings/i2c/ina2xx.txt b/Documentation/devicetree/bindings/i2c/ina2xx.txt
deleted file mode 100644
index a2ad85d7e..000000000
--- a/Documentation/devicetree/bindings/i2c/ina2xx.txt
+++ /dev/null
@@ -1,22 +0,0 @@
-ina2xx properties
-
-Required properties:
-- compatible: Must be one of the following:
-	- "ti,ina219" for ina219
-	- "ti,ina220" for ina220
-	- "ti,ina226" for ina226
-	- "ti,ina230" for ina230
-- reg: I2C address
-
-Optional properties:
-
-- shunt-resistor
-	Shunt resistor value in micro-Ohm
-
-Example:
-
-ina220@44 {
-	compatible = "ti,ina220";
-	reg = <0x44>;
-	shunt-resistor = <1000>;
-};
diff --git a/Documentation/devicetree/bindings/i2c/max6697.txt b/Documentation/devicetree/bindings/i2c/max6697.txt
deleted file mode 100644
index 5f793998e..000000000
--- a/Documentation/devicetree/bindings/i2c/max6697.txt
+++ /dev/null
@@ -1,64 +0,0 @@
-max6697 properties
-
-Required properties:
-- compatible:
-	Should be one of
-		maxim,max6581
-		maxim,max6602
-		maxim,max6622
-		maxim,max6636
-		maxim,max6689
-		maxim,max6693
-		maxim,max6694
-		maxim,max6697
-		maxim,max6698
-		maxim,max6699
-- reg: I2C address
-
-Optional properties:
-
-- smbus-timeout-disable
-	Set to disable SMBus timeout. If not specified, SMBus timeout will be
-	enabled.
-- extended-range-enable
-	Only valid for MAX6581. Set to enable extended temperature range.
-	Extended temperature will be disabled if not specified.
-- beta-compensation-enable
-	Only valid for MAX6693 and MX6694. Set to enable beta compensation on
-	remote temperature channel 1.
-	Beta compensation will be disabled if not specified.
-- alert-mask
-	Alert bit mask. Alert disabled for bits set.
-	Select bit 0 for local temperature, bit 1..7 for remote temperatures.
-	If not specified, alert will be enabled for all channels.
-- over-temperature-mask
-	Over-temperature bit mask. Over-temperature reporting disabled for
-	bits set.
-	Select bit 0 for local temperature, bit 1..7 for remote temperatures.
-	If not specified, over-temperature reporting will be enabled for all
-	channels.
-- resistance-cancellation
-	Boolean for all chips other than MAX6581. Set to enable resistance
-	cancellation on remote temperature channel 1.
-	For MAX6581, resistance cancellation enabled for all channels if
-	specified as boolean, otherwise as per bit mask specified.
-	Only supported for remote temperatures (bit 1..7).
-	If not specified, resistance cancellation will be disabled for all
-	channels.
-- transistor-ideality
-	For MAX6581 only. Two values; first is bit mask, second is ideality
-	select value as per MAX6581 data sheet. Select bit 1..7 for remote
-	channels.
-	Transistor ideality will be initialized to default (1.008) if not
-	specified.
-
-Example:
-
-temp-sensor@1a {
-	compatible = "maxim,max6697";
-	reg = <0x1a>;
-	smbus-timeout-disable;
-	resistance-cancellation;
-	alert-mask = <0x72>;
-	over-temperature-mask = <0x7f>;
-};
diff --git a/Documentation/devicetree/bindings/i2c/ti,bq32k.txt b/Documentation/devicetree/bindings/i2c/ti,bq32k.txt
deleted file mode 100644
index e204906b9..000000000
--- a/Documentation/devicetree/bindings/i2c/ti,bq32k.txt
+++ /dev/null
@@ -1,18 +0,0 @@
-* TI BQ32000                I2C Serial Real-Time Clock
-
-Required properties:
-- compatible: Should contain "ti,bq32000".
-- reg: I2C address for chip
-
-Optional properties:
-- trickle-resistor-ohms : Selected resistor for trickle charger
-       Values usable are 1120 and 20180
-       Should be given if trickle charger should be enabled
-- trickle-diode-disable : Do not use internal trickle charger diode
-       Should be given if internal trickle charger diode should be disabled
-Example:
-       bq32000: rtc@68 {
-               compatible = "ti,bq32000";
-               trickle-resistor-ohms = <1120>;
-               reg = <0x68>;
-       };
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 00f8652e1..d77d412cb 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -95,6 +95,8 @@ stm,m41t00		Serial Access TIMEKEEPER
 stm,m41t62		Serial real-time clock (RTC) with alarm
 stm,m41t80		M41T80 - SERIAL ACCESS RTC WITH ALARMS
 taos,tsl2550		Ambient Light Sensor with SMBUS/Two Wire Serial Interface
+ti,ads7828		8-Channels, 12-bit ADC
+ti,ads7830		8-Channels, 8-bit ADC
 ti,tsc2003		I2C Touch-Screen Controller
 ti,tmp102		Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface
 ti,tmp103		Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface