Linux-libre 4.6.2-gnu

10 files changed, 393 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/input/ads7846.txt b/Documentation/devicetree/bindings/input/ads7846.txt
index 33a1638b6..c6cfe2e3e 100644
--- a/Documentation/devicetree/bindings/input/ads7846.txt
+++ b/Documentation/devicetree/bindings/input/ads7846.txt
@@ -29,6 +29,8 @@ Optional properties:
 	ti,vref-delay-usecs		vref supply delay in usecs, 0 for
 					external vref (u16).
 	ti,vref-mv			The VREF voltage, in millivolts (u16).
+					Set to 0 to use internal refernce
+					(ADS7846).
 	ti,keep-vref-on			set to keep vref on for differential
 					measurements as well
 	ti,swap-xy			swap x and y axis
diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt
new file mode 100644
index 000000000..f2c30c8b7
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/rmi4/rmi_2d_sensor.txt
@@ -0,0 +1,56 @@
+Synaptics RMI4 2D Sensor Device Binding
+
+The Synaptics RMI4 core is able to support RMI4 devices using different
+transports and different functions. This file describes the device tree
+bindings for devices which contain 2D sensors using Function 11 or
+Function 12. Complete documentation for transports and other functions
+can be found in:
+Documentation/devicetree/bindings/input/rmi4.
+
+RMI4 Function 11 and Function 12 are for 2D touch position sensing.
+Additional documentation for F11 can be found at:
+http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf
+
+Optional Touch Properties:
+Description in Documentation/devicetree/bindings/input/touch
+- touchscreen-inverted-x
+- touchscreen-inverted-y
+- touchscreen-swapped-x-y
+- touchscreen-x-mm
+- touchscreen-y-mm
+
+Optional Properties:
+- syna,clip-x-low: Sets a minimum value for X.
+- syna,clip-y-low: Sets a minimum value for Y.
+- syna,clip-x-high: Sets a maximum value for X.
+- syna,clip-y-high: Sets a maximum value for Y.
+- syna,offset-x: Add an offset to X.
+- syna,offset-y: Add an offset to Y.
+- syna,delta-x-threshold: Set the minimum distance on the X axis required
+				to generate an interrupt in reduced reporting
+				mode.
+- syna,delta-y-threshold: Set the minimum distance on the Y axis required
+				to generate an interrupt in reduced reporting
+				mode.
+- syna,sensor-type: Set the sensor type. 1 for touchscreen 2 for touchpad.
+- syna,disable-report-mask: Mask for disabling posiiton reporting. Used to
+				disable reporing absolute position data.
+- syna,rezero-wait-ms: Time in miliseconds to wait after issuing a rezero
+				command.
+
+
+Example of a RMI4 I2C device with F11:
+Example:
+	&i2c1 {
+		rmi4-i2c-dev@2c {
+			compatible = "syna,rmi4-i2c";
+
+			...
+
+			rmi4-f11@11 {
+				reg = <0x11>;
+				touchscreen-inverted-y;
+				syna,sensor-type = <2>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt
new file mode 100644
index 000000000..079cad2b6
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/rmi4/rmi_f01.txt
@@ -0,0 +1,39 @@
+Synaptics RMI4 F01 Device Binding
+
+The Synaptics RMI4 core is able to support RMI4 devices using different
+transports and different functions. This file describes the device tree
+bindings for devices which contain Function 1. Complete documentation
+for transports and other functions can be found in:
+Documentation/devicetree/bindings/input/rmi4.
+
+Additional documentation for F01 can be found at:
+http://www.synaptics.com/sites/default/files/511-000136-01-Rev-E-RMI4-Interfacing-Guide.pdf
+
+Optional Properties:
+- syna,nosleep-mode: If set the device will run at full power without sleeping.
+			nosleep has 3 modes, 0 will not change the default
+			setting, 1 will disable nosleep (allow sleeping),
+			and 2 will enable nosleep (disabling sleep).
+- syna,wakeup-threshold: Defines the amplitude of the disturbance to the
+				background capacitance that will cause the
+				device to wake from dozing.
+- syna,doze-holdoff-ms: The delay to wait after the last finger lift and the
+				first doze cycle.
+- syna,doze-interval-ms: The time period that the device sleeps between finger
+				activity.
+
+
+Example of a RMI4 I2C device with F01:
+	Example:
+	&i2c1 {
+		rmi4-i2c-dev@2c {
+			compatible = "syna,rmi4-i2c";
+
+			...
+
+			rmi4-f01@1 {
+				reg = <0x1>;
+				syna,nosleep-mode = <1>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt
new file mode 100644
index 000000000..95fa715c6
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/rmi4/rmi_i2c.txt
@@ -0,0 +1,53 @@
+Synaptics RMI4 I2C Device Binding
+
+The Synaptics RMI4 core is able to support RMI4 devices using different
+transports and different functions. This file describes the device tree
+bindings for devices using the I2C transport driver. Complete documentation
+for other transports and functions can be found in
+Documentation/devicetree/bindings/input/rmi4.
+
+Required Properties:
+- compatible: syna,rmi4-i2c
+- reg: I2C address
+- #address-cells: Set to 1 to indicate that the function child nodes
+		    consist of only on uint32 value.
+- #size-cells: Set to 0 to indicate that the function child nodes do not
+		have a size property.
+
+Optional Properties:
+- interrupts: interrupt which the rmi device is connected to.
+- interrupt-parent: The interrupt controller.
+See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+- syna,reset-delay-ms: The number of milliseconds to wait after resetting the
+			device.
+
+Function Parameters:
+Parameters specific to RMI functions are contained in child nodes of the rmi device
+ node. Documentation for the parameters of each function can be found in:
+Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt.
+
+
+
+Example:
+	&i2c1 {
+		rmi4-i2c-dev@2c {
+			compatible = "syna,rmi4-i2c";
+			reg = <0x2c>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupt-parent = <&gpio>;
+			interrupts = <4 2>;
+
+			rmi4-f01@1 {
+				reg = <0x1>;
+				syna,nosleep-mode = <1>;
+			};
+
+			rmi4-f11@11 {
+				reg = <0x11>;
+				touchscreen-inverted-y;
+				syna,sensor-type = <2>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt b/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt
new file mode 100644
index 000000000..a4ca7828f
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/rmi4/rmi_spi.txt
@@ -0,0 +1,57 @@
+Synaptics RMI4 SPI Device Binding
+
+The Synaptics RMI4 core is able to support RMI4 devices using different
+transports and different functions. This file describes the device tree
+bindings for devices using the SPI transport driver. Complete documentation
+for other transports and functions can be found in
+Documentation/devicetree/bindings/input/rmi4.
+
+Required Properties:
+- compatible: syna,rmi4-spi
+- reg: Chip select address for the device
+- #address-cells: Set to 1 to indicate that the function child nodes
+		    consist of only on uint32 value.
+- #size-cells: Set to 0 to indicate that the function child nodes do not
+		have a size property.
+
+Optional Properties:
+- interrupts: interrupt which the rmi device is connected to.
+- interrupt-parent: The interrupt controller.
+See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+- spi-rx-delay-us: microsecond delay after a read transfer.
+- spi-tx-delay-us: microsecond delay after a write transfer.
+
+Function Parameters:
+Parameters specific to RMI functions are contained in child nodes of the rmi device
+ node. Documentation for the parameters of each function can be found in:
+Documentation/devicetree/bindings/input/rmi4/rmi_f*.txt.
+
+
+
+Example:
+	spi@7000d800 {
+		rmi4-spi-dev@0 {
+			compatible = "syna,rmi4-spi";
+			reg = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			spi-max-frequency = <4000000>;
+			spi-cpha;
+			spi-cpol;
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(K, 2) 0x2>;
+			spi-rx-delay-us = <30>;
+
+			rmi4-f01@1 {
+				reg = <0x1>;
+				syna,nosleep-mode = <1>;
+			};
+
+			rmi4-f11@11 {
+				reg = <0x11>;
+				touchscreen-inverted-y;
+				syna,sensor-type = <2>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.txt b/Documentation/devicetree/bindings/input/rotary-encoder.txt
index de99cbbbf..6c9f0c8a8 100644
--- a/Documentation/devicetree/bindings/input/rotary-encoder.txt
+++ b/Documentation/devicetree/bindings/input/rotary-encoder.txt
@@ -1,7 +1,7 @@
 Rotary encoder DT bindings
 
 Required properties:
-- gpios: a spec for two GPIOs to be used
+- gpios: a spec for at least two GPIOs to be used, most significant first
 
 Optional properties:
 - linux,axis: the input subsystem axis to map to this rotary encoder.
diff --git a/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt
new file mode 100644
index 000000000..e3f22d23f
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/ad7879.txt
@@ -0,0 +1,53 @@
+* Analog Devices AD7879(-1)/AD7889(-1) touchscreen interface (SPI/I2C)
+
+Required properties:
+- compatible			: for SPI slave, use "adi,ad7879"
+				  for I2C slave, use "adi,ad7879-1"
+- reg				: SPI chipselect/I2C slave address
+				  See spi-bus.txt for more SPI slave properties
+- interrupt-parent		: the phandle for the interrupt controller
+- interrupts			: touch controller interrupt
+- touchscreen-max-pressure	: maximum reported pressure
+- adi,resistance-plate-x	: total resistance of X-plate (for pressure
+				  calculation)
+Optional properties:
+- touchscreen-swapped-x-y	: X and Y axis are swapped (boolean)
+- adi,first-conversion-delay	: 0-12: In 128us steps (starting with 128us)
+				  13  : 2.560ms
+				  14  : 3.584ms
+				  15  : 4.096ms
+				  This property has to be a '/bits/ 8' value
+- adi,acquisition-time		: 0: 2us
+				  1: 4us
+				  2: 8us
+				  3: 16us
+				  This property has to be a '/bits/ 8' value
+- adi,median-filter-size	: 0: disabled
+				  1: 4 measurements
+				  2: 8 measurements
+				  3: 16 measurements
+				  This property has to be a '/bits/ 8' value
+- adi,averaging			: 0: 2 middle values (1 if median disabled)
+				  1: 4 middle values
+				  2: 8 middle values
+				  3: 16 values
+				  This property has to be a '/bits/ 8' value
+- adi,conversion-interval:	: 0    : convert one time only
+				  1-255: 515us + val * 35us (up to 9.440ms)
+				  This property has to be a '/bits/ 8' value
+
+Example:
+
+	ad7879@2c {
+		compatible = "adi,ad7879-1";
+		reg = <0x2c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-max-pressure = <4096>;
+		adi,resistance-plate-x = <120>;
+		adi,first-conversion-delay = /bits/ 8 <3>;
+		adi,acquisition-time = /bits/ 8 <1>;
+		adi,median-filter-size = /bits/ 8 <2>;
+		adi,averaging = /bits/ 8 <1>;
+		adi,conversion-interval = /bits/ 8 <255>;
+	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt
new file mode 100644
index 000000000..b75d4cfd2
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/cyttsp.txt
@@ -0,0 +1,95 @@
+* Cypress cyttsp touchscreen controller
+
+Required properties:
+ - compatible		: must be "cypress,cyttsp-i2c" or "cypress,cyttsp-spi"
+ - reg			: Device I2C address or SPI chip select number
+ - spi-max-frequency	: Maximum SPI clocking speed of the device (for cyttsp-spi)
+ - interrupt-parent	: the phandle for the gpio controller
+			  (see interrupt binding[0]).
+ - interrupts		: (gpio) interrupt to which the chip is connected
+			  (see interrupt binding[0]).
+ - bootloader-key	: the 8-byte bootloader key that is required to switch
+			  the chip from bootloader mode (default mode) to
+			  application mode.
+			  This property has to be specified as an array of 8
+			  '/bits/ 8' values.
+
+Optional properties:
+ - reset-gpios		: the reset gpio the chip is connected to
+			  (see GPIO binding[1] for more details).
+ - touchscreen-size-x	: horizontal resolution of touchscreen (in pixels)
+ - touchscreen-size-y	: vertical resolution of touchscreen (in pixels)
+ - touchscreen-fuzz-x	: horizontal noise value of the absolute input device
+			  (in pixels)
+ - touchscreen-fuzz-y	: vertical noise value of the absolute input device
+			  (in pixels)
+ - active-distance	: the distance in pixels beyond which a touch must move
+			  before movement is detected and reported by the device.
+			  Valid values: 0-15.
+ - active-interval-ms	: the minimum period in ms between consecutive
+			  scanning/processing cycles when the chip is in active mode.
+			  Valid values: 0-255.
+ - lowpower-interval-ms	: the minimum period in ms between consecutive
+			  scanning/processing cycles when the chip is in low-power mode.
+			  Valid values: 0-2550
+ - touch-timeout-ms	: minimum time in ms spent in the active power state while no
+			  touches are detected before entering low-power mode.
+			  Valid values: 0-2550
+ - use-handshake	: enable register-based handshake (boolean). This should
+			  only be used if the chip is configured to use 'blocking
+			  communication with timeout' (in this case the device
+			  generates an interrupt at the end of every
+			  scanning/processing cycle).
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/gpio/gpio.txt
+
+Example:
+	&i2c1 {
+		/* ... */
+		cyttsp@a {
+			compatible = "cypress,cyttsp-i2c";
+			reg = <0xa>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <28 0>;
+			reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
+
+			touchscreen-size-x = <800>;
+			touchscreen-size-y = <480>;
+			touchscreen-fuzz-x = <4>;
+			touchscreen-fuzz-y = <7>;
+
+			bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>;
+			active-distance = <8>;
+			active-interval-ms = <0>;
+			lowpower-interval-ms = <200>;
+			touch-timeout-ms = <100>;
+		};
+
+		/* ... */
+	};
+
+	&mcspi1 {
+		/* ... */
+		cyttsp@0 {
+			compatible = "cypress,cyttsp-spi";
+			spi-max-frequency = <6000000>;
+			reg = <0>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <28 0>;
+			reset-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
+
+			touchscreen-size-x = <800>;
+			touchscreen-size-y = <480>;
+			touchscreen-fuzz-x = <4>;
+			touchscreen-fuzz-y = <7>;
+
+			bootloader-key = /bits/ 8 <0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08>;
+			active-distance = <8>;
+			active-interval-ms = <0>;
+			lowpower-interval-ms = <200>;
+			touch-timeout-ms = <100>;
+		};
+
+		/* ... */
+	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
new file mode 100644
index 000000000..cdf05f9b2
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/fsl-mx25-tcq.txt
@@ -0,0 +1,35 @@
+Freescale mx25 TS conversion queue module
+
+mx25 touchscreen conversion queue module which controls the ADC unit of the
+mx25 for attached touchscreens.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-tcq".
+ - reg: Memory range of the device.
+ - interrupts: Should be the interrupt number associated with this module within
+   the tscadc unit (<0>).
+ - interrupt-parent: Should be a phandle to the tscadc unit.
+ - fsl,wires: Should be '<4>' or '<5>'
+
+Optional properties:
+ - fsl,pen-debounce-ns: Pen debounce time in nanoseconds.
+ - fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value
+   between 1 and 4096. It is the ratio between the internal reference voltage
+   and the measured voltage after the plate was precharged. Resistence between
+   plates and therefore the voltage decreases with pressure so that a smaller
+   value is equivalent to a higher pressure.
+ - fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before
+   the actual touch detection to wait for an even charge distribution in the
+   plate.
+
+This device includes two conversion queues which can be added as subnodes.
+The first queue is for the touchscreen, the second for general purpose ADC.
+
+Example:
+	tsc: tcq@50030400 {
+		compatible = "fsl,imx25-tcq";
+		reg = <0x50030400 0x60>;
+		interrupt-parent = <&tscadc>;
+		interrupts = <0>;
+		fsl,wires = <4>;
+	};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
index ac23caf51..bccaa4e73 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
@@ -18,6 +18,8 @@ Optional properties for Touchscreens:
  - touchscreen-inverted-y	: Y axis is inverted (boolean)
  - touchscreen-swapped-x-y	: X and Y axis are swapped (boolean)
 				  Swapping is done after inverting the axis
+ - touchscreen-x-mm		: horizontal length in mm of the touchscreen
+ - touchscreen-y-mm		: vertical length in mm of the touchscreen
 
 Deprecated properties for Touchscreens:
  - x-size			: deprecated name for touchscreen-size-x