Initial import

28 files changed, 1170 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/interrupt-controller/abilis,tb10x-ictl.txt b/Documentation/devicetree/bindings/interrupt-controller/abilis,tb10x-ictl.txt
new file mode 100644
index 000000000..9d52d5afe
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/abilis,tb10x-ictl.txt
@@ -0,0 +1,38 @@
+TB10x Top Level Interrupt Controller
+====================================
+
+The Abilis TB10x SOC contains a custom interrupt controller. It performs
+one-to-one mapping of external interrupt sources to CPU interrupts and
+provides support for reconfigurable trigger modes.
+
+Required properties
+-------------------
+
+- compatible: Should be "abilis,tb10x-ictl"
+- reg: specifies physical base address and size of register range.
+- interrupt-congroller: Identifies the node as an interrupt controller.
+- #interrupt cells: Specifies the number of cells used to encode an interrupt
+  source connected to this controller. The value shall be 2.
+- interrupt-parent: Specifies the parent interrupt controller.
+- interrupts: Specifies the list of interrupt lines which are handled by
+  the interrupt controller in the parent controller's notation. Interrupts
+  are mapped one-to-one to parent interrupts.
+
+Example
+-------
+
+intc: interrupt-controller {	/* Parent interrupt controller */
+	interrupt-controller;
+	#interrupt-cells = <1>;	/* For example below */
+	/* ... */
+};
+
+tb10x_ictl: pic@2000 {		/* TB10x interrupt controller */
+	compatible = "abilis,tb10x-ictl";
+	reg = <0x2000 0x20>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+	interrupt-parent = <&intc>;
+	interrupts = <5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
+			20 21 22 23 24 25 26 27 28 29 30 31>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt
new file mode 100644
index 000000000..b290ca150
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun4i-ic.txt
@@ -0,0 +1,18 @@
+Allwinner Sunxi Interrupt Controller
+
+Required properties:
+
+- compatible : should be "allwinner,sun4i-a10-ic"
+- reg : Specifies base physical address and size of the registers.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 1.
+
+Example:
+
+intc: interrupt-controller {
+	compatible = "allwinner,sun4i-a10-ic";
+	reg = <0x01c20400 0x400>;
+	interrupt-controller;
+	#interrupt-cells = <1>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun67i-sc-nmi.txt b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun67i-sc-nmi.txt
new file mode 100644
index 000000000..d1c5cdabc
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun67i-sc-nmi.txt
@@ -0,0 +1,27 @@
+Allwinner Sunxi NMI Controller
+==============================
+
+Required properties:
+
+- compatible : should be "allwinner,sun7i-a20-sc-nmi" or
+  "allwinner,sun6i-a31-sc-nmi"
+- reg : Specifies base physical address and size of the registers.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 2. The first cell is the IRQ number, the
+  second cell the trigger type as defined in interrupt.txt in this directory.
+- interrupt-parent: Specifies the parent interrupt controller.
+- interrupts: Specifies the interrupt line (NMI) which is handled by
+  the interrupt controller in the parent controller's notation. This value
+  shall be the NMI.
+
+Example:
+
+sc-nmi-intc@01c00030 {
+	compatible = "allwinner,sun7i-a20-sc-nmi";
+	interrupt-controller;
+	#interrupt-cells = <2>;
+	reg = <0x01c00030 0x0c>;
+	interrupt-parent = <&gic>;
+	interrupts = <0 0 4>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt b/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt
new file mode 100644
index 000000000..f292917fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt
@@ -0,0 +1,42 @@
+* Advanced Interrupt Controller (AIC)
+
+Required properties:
+- compatible: Should be "atmel,<chip>-aic"
+  <chip> can be "at91rm9200", "sama5d3" or "sama5d4"
+- interrupt-controller: Identifies the node as an interrupt controller.
+- interrupt-parent: For single AIC system, it is an empty property.
+- #interrupt-cells: The number of cells to define the interrupts. It should be 3.
+  The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet).
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+      Valid combinations are 1, 2, 3, 4, 8.
+      Default flag for internal sources should be set to 4 (active high).
+  The third cell is used to specify the irq priority from 0 (lowest) to 7
+  (highest).
+- reg: Should contain AIC registers location and length
+- atmel,external-irqs: u32 array of external irqs.
+
+Examples:
+	/*
+	 * AIC
+	 */
+	aic: interrupt-controller@fffff000 {
+		compatible = "atmel,at91rm9200-aic";
+		interrupt-controller;
+		interrupt-parent;
+		#interrupt-cells = <3>;
+		reg = <0xfffff000 0x200>;
+	};
+
+	/*
+	 * An interrupt generating device that is wired to an AIC.
+	 */
+	dma: dma-controller@ffffec00 {
+		compatible = "atmel,at91sam9g45-dma";
+		reg = <0xffffec00 0x200>;
+		interrupts = <21 4 5>;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
new file mode 100644
index 000000000..7da578d72
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
@@ -0,0 +1,110 @@
+BCM2835 Top-Level ("ARMCTRL") Interrupt Controller
+
+The BCM2835 contains a custom top-level interrupt controller, which supports
+72 interrupt sources using a 2-level register scheme. The interrupt
+controller, or the HW block containing it, is referred to occasionally
+as "armctrl" in the SoC documentation, hence naming of this binding.
+
+Required properties:
+
+- compatible : should be "brcm,bcm2835-armctrl-ic"
+- reg : Specifies base physical address and size of the registers.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 2.
+
+  The 1st cell is the interrupt bank; 0 for interrupts in the "IRQ basic
+  pending" register, or 1/2 respectively for interrupts in the "IRQ pending
+  1/2" register.
+
+  The 2nd cell contains the interrupt number within the bank. Valid values
+  are 0..7 for bank 0, and 0..31 for bank 1.
+
+The interrupt sources are as follows:
+
+Bank 0:
+0: ARM_TIMER
+1: ARM_MAILBOX
+2: ARM_DOORBELL_0
+3: ARM_DOORBELL_1
+4: VPU0_HALTED
+5: VPU1_HALTED
+6: ILLEGAL_TYPE0
+7: ILLEGAL_TYPE1
+
+Bank 1:
+0: TIMER0
+1: TIMER1
+2: TIMER2
+3: TIMER3
+4: CODEC0
+5: CODEC1
+6: CODEC2
+7: VC_JPEG
+8: ISP
+9: VC_USB
+10: VC_3D
+11: TRANSPOSER
+12: MULTICORESYNC0
+13: MULTICORESYNC1
+14: MULTICORESYNC2
+15: MULTICORESYNC3
+16: DMA0
+17: DMA1
+18: VC_DMA2
+19: VC_DMA3
+20: DMA4
+21: DMA5
+22: DMA6
+23: DMA7
+24: DMA8
+25: DMA9
+26: DMA10
+27: DMA11
+28: DMA12
+29: AUX
+30: ARM
+31: VPUDMA
+
+Bank 2:
+0: HOSTPORT
+1: VIDEOSCALER
+2: CCP2TX
+3: SDC
+4: DSI0
+5: AVE
+6: CAM0
+7: CAM1
+8: HDMI0
+9: HDMI1
+10: PIXELVALVE1
+11: I2CSPISLV
+12: DSI1
+13: PWA0
+14: PWA1
+15: CPR
+16: SMI
+17: GPIO0
+18: GPIO1
+19: GPIO2
+20: GPIO3
+21: VC_I2C
+22: VC_SPI
+23: VC_I2SPCM
+24: VC_SDIO
+25: VC_UART
+26: SLIMBUS
+27: VEC
+28: CPG
+29: RNG
+30: VC_ARASANSDIO
+31: AVSPMON
+
+Example:
+
+intc: interrupt-controller {
+	compatible = "brcm,bcm2835-armctrl-ic";
+	reg = <0x7e00b200 0x200>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt
new file mode 100644
index 000000000..8f48aad50
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm3380-l2-intc.txt
@@ -0,0 +1,41 @@
+Broadcom BCM3380-style Level 1 / Level 2 interrupt controller
+
+This interrupt controller shows up in various forms on many BCM338x/BCM63xx
+chipsets.  It has the following properties:
+
+- outputs a single interrupt signal to its interrupt controller parent
+
+- contains one or more enable/status word pairs, which often appear at
+  different offsets in different blocks
+
+- no atomic set/clear operations
+
+Required properties:
+
+- compatible: should be "brcm,bcm3380-l2-intc"
+- reg: specifies one or more enable/status pairs, in the following format:
+  <enable_reg 0x4 status_reg 0x4>...
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+  source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller
+  this one is cascaded from
+- interrupts: specifies the interrupt line in the interrupt-parent controller
+  node, valid values depend on the type of parent interrupt controller
+
+Optional properties:
+
+- brcm,irq-can-wake: if present, this means the L2 controller can be used as a
+  wakeup source for system suspend/resume.
+
+Example:
+
+irq0_intc: interrupt-controller@10000020 {
+	compatible = "brcm,bcm3380-l2-intc";
+	reg = <0x10000024 0x4 0x1000002c 0x4>,
+	      <0x10000020 0x4 0x10000028 0x4>;
+	interrupt-controller;
+	#interrupt-cells = <1>;
+	interrupt-parent = <&cpu_intc>;
+	interrupts = <2>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt
new file mode 100644
index 000000000..cc217b22d
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7038-l1-intc.txt
@@ -0,0 +1,52 @@
+Broadcom BCM7038-style Level 1 interrupt controller
+
+This block is a first level interrupt controller that is typically connected
+directly to one of the HW INT lines on each CPU.  Every BCM7xxx set-top chip
+since BCM7038 has contained this hardware.
+
+Key elements of the hardware design include:
+
+- 64, 96, 128, or 160 incoming level IRQ lines
+
+- Most onchip peripherals are wired directly to an L1 input
+
+- A separate instance of the register set for each CPU, allowing individual
+  peripheral IRQs to be routed to any CPU
+
+- Atomic mask/unmask operations
+
+- No polarity/level/edge settings
+
+- No FIFO or priority encoder logic; software is expected to read all
+  2-5 status words to determine which IRQs are pending
+
+Required properties:
+
+- compatible: should be "brcm,bcm7038-l1-intc"
+- reg: specifies the base physical address and size of the registers;
+  the number of supported IRQs is inferred from the size argument
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+  source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller(s)
+  this one is cascaded from
+- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
+  node; valid values depend on the type of parent interrupt controller
+
+If multiple reg ranges and interrupt-parent entries are present on an SMP
+system, the driver will allow IRQ SMP affinity to be set up through the
+/proc/irq/ interface.  In the simplest possible configuration, only one
+reg range and one interrupt-parent is needed.
+
+Example:
+
+periph_intc: periph_intc@1041a400 {
+        compatible = "brcm,bcm7038-l1-intc";
+        reg = <0x1041a400 0x30 0x1041a600 0x30>;
+
+        interrupt-controller;
+        #interrupt-cells = <1>;
+
+        interrupt-parent = <&cpu_intc>;
+        interrupts = <2>, <3>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt
new file mode 100644
index 000000000..44a9bb15d
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt
@@ -0,0 +1,90 @@
+Broadcom BCM7120-style Level 2 interrupt controller
+
+This interrupt controller hardware is a second level interrupt controller that
+is hooked to a parent interrupt controller: e.g: ARM GIC for ARM-based
+platforms. It can be found on BCM7xxx products starting with BCM7120.
+
+Such an interrupt controller has the following hardware design:
+
+- outputs multiple interrupts signals towards its interrupt controller parent
+
+- controls how some of the interrupts will be flowing, whether they will
+  directly output an interrupt signal towards the interrupt controller parent,
+  or if they will output an interrupt signal at this 2nd level interrupt
+  controller, in particular for UARTs
+
+- has one 32-bit enable word and one 32-bit status word
+
+- no atomic set/clear operations
+
+- not all bits within the interrupt controller actually map to an interrupt
+
+The typical hardware layout for this controller is represented below:
+
+2nd level interrupt line		Outputs for the parent controller (e.g: ARM GIC)
+
+0 -----[ MUX ] ------------|==========> GIC interrupt 75
+          \-----------\
+                       |
+1 -----[ MUX ] --------)---|==========> GIC interrupt 76
+          \------------|
+                       |
+2 -----[ MUX ] --------)---|==========> GIC interrupt 77
+          \------------|
+                       |
+3 ---------------------|
+4 ---------------------|
+5 ---------------------|
+7 ---------------------|---|===========> GIC interrupt 66
+9 ---------------------|
+10 --------------------|
+11 --------------------/
+
+6 ------------------------\
+                           |===========> GIC interrupt 64
+8 ------------------------/
+
+12 ........................ X
+13 ........................ X 		(not connected)
+..
+31 ........................ X
+
+Required properties:
+
+- compatible: should be "brcm,bcm7120-l2-intc"
+- reg: specifies the base physical address and size of the registers
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+  source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller
+  this one is cascaded from
+- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
+  node, valid values depend on the type of parent interrupt controller
+- brcm,int-map-mask: 32-bits bit mask describing how many and which interrupts
+  are wired to this 2nd level interrupt controller, and how they match their
+  respective interrupt parents. Should match exactly the number of interrupts
+  specified in the 'interrupts' property.
+
+Optional properties:
+
+- brcm,irq-can-wake: if present, this means the L2 controller can be used as a
+  wakeup source for system suspend/resume.
+
+- brcm,int-fwd-mask: if present, a bit mask to configure the interrupts which
+  have a mux gate, typically UARTs. Setting these bits will make their
+  respective interrupt outputs bypass this 2nd level interrupt controller
+  completely; it is completely transparent for the interrupt controller
+  parent. This should have one 32-bit word per enable/status pair.
+
+Example:
+
+irq0_intc: interrupt-controller@f0406800 {
+	compatible = "brcm,bcm7120-l2-intc";
+	interrupt-parent = <&intc>;
+	#interrupt-cells = <1>;
+	reg = <0xf0406800 0x8>;
+	interrupt-controller;
+	interrupts = <0x0 0x42 0x0>, <0x0 0x40 0x0>;
+	brcm,int-map-mask = <0xeb8>, <0x140>;
+	brcm,int-fwd-mask = <0x7>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt
new file mode 100644
index 000000000..448273a30
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,l2-intc.txt
@@ -0,0 +1,29 @@
+Broadcom Generic Level 2 Interrupt Controller
+
+Required properties:
+
+- compatible: should be "brcm,l2-intc"
+- reg: specifies the base physical address and size of the registers
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an
+  interrupt source. Should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller
+  this controller is cacaded from
+- interrupts: specifies the interrupt line in the interrupt-parent irq space
+  to be used for cascading
+
+Optional properties:
+
+- brcm,irq-can-wake: If present, this means the L2 controller can be used as a
+  wakeup source for system suspend/resume.
+
+Example:
+
+hif_intr2_intc: interrupt-controller@f0441000 {
+	compatible = "brcm,l2-intc";
+	reg = <0xf0441000 0x30>;
+	interrupt-controller;
+	#interrupt-cells = <1>;
+	interrupt-parent = <&intc>;
+	interrupts = <0x0 0x20 0x0>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/cdns,xtensa-mx.txt b/Documentation/devicetree/bindings/interrupt-controller/cdns,xtensa-mx.txt
new file mode 100644
index 000000000..d4de980e5
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/cdns,xtensa-mx.txt
@@ -0,0 +1,18 @@
+* Xtensa Interrupt Distributor and Programmable Interrupt Controller (MX)
+
+Required properties:
+- compatible: Should be "cdns,xtensa-mx".
+
+Remaining properties have exact same meaning as in Xtensa PIC
+(see cdns,xtensa-pic.txt).
+
+Examples:
+	pic: pic {
+		compatible = "cdns,xtensa-mx";
+		/* one cell: internal irq number,
+		 * two cells: second cell == 0: internal irq number
+		 *            second cell == 1: external irq number
+		 */
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/cdns,xtensa-pic.txt b/Documentation/devicetree/bindings/interrupt-controller/cdns,xtensa-pic.txt
new file mode 100644
index 000000000..026ef4cfc
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/cdns,xtensa-pic.txt
@@ -0,0 +1,25 @@
+* Xtensa built-in Programmable Interrupt Controller (PIC)
+
+Required properties:
+- compatible: Should be "cdns,xtensa-pic".
+- interrupt-controller: Identifies the node as an interrupt controller.
+- #interrupt-cells: The number of cells to define the interrupts.
+  It may be either 1 or 2.
+  When it's 1, the first cell is the internal IRQ number.
+  When it's 2, the first cell is the IRQ number, and the second cell
+  specifies whether it's internal (0) or external (1).
+  Periferals are usually connected to a fixed external IRQ, but for different
+  core variants it may be mapped to different internal IRQ.
+  IRQ sensitivity and priority are fixed for each core variant and may not be
+  changed at runtime.
+
+Examples:
+	pic: pic {
+		compatible = "cdns,xtensa-pic";
+		/* one cell: internal irq number,
+		 * two cells: second cell == 0: internal irq number
+		 *            second cell == 1: external irq number
+		 */
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt
new file mode 100644
index 000000000..759339c34
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt
@@ -0,0 +1,41 @@
+Cirrus Logic CLPS711X Interrupt Controller
+
+Required properties:
+
+- compatible: Should be "cirrus,clps711x-intc".
+- reg: Specifies base physical address of the registers set.
+- interrupt-controller: Identifies the node as an interrupt controller.
+- #interrupt-cells: Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 1.
+
+The interrupt sources are as follows:
+ID	Name	Description
+---------------------------
+1:	BLINT	Battery low (FIQ)
+3:	MCINT	Media changed (FIQ)
+4:	CSINT	CODEC sound
+5:	EINT1	External 1
+6:	EINT2	External 2
+7:	EINT3	External 3
+8:	TC1OI	TC1 under flow
+9:	TC2OI	TC2 under flow
+10:	RTCMI	RTC compare match
+11:	TINT	64Hz tick
+12:	UTXINT1	UART1 transmit FIFO half empty
+13:	URXINT1	UART1 receive FIFO half full
+14:	UMSINT	UART1 modem status changed
+15:	SSEOTI	SSI1 end of transfer
+16:	KBDINT	Keyboard
+17:	SS2RX	SSI2 receive FIFO half or greater full
+18:	SS2TX	SSI2 transmit FIFO less than half empty
+28:	UTXINT2	UART2 transmit FIFO half empty
+29:	URXINT2	UART2 receive FIFO half full
+32:	DAIINT	DAI interface (FIQ)
+
+Example:
+	intc: interrupt-controller {
+		compatible = "cirrus,clps711x-intc";
+		reg = <0x80000000 0x4000>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/digicolor-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/digicolor-ic.txt
new file mode 100644
index 000000000..42d41ec84
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/digicolor-ic.txt
@@ -0,0 +1,21 @@
+Conexant Digicolor Interrupt Controller
+
+Required properties:
+
+- compatible : should be "cnxt,cx92755-ic"
+- reg : Specifies base physical address and size of the interrupt controller
+  registers (IC) area
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 1.
+- syscon: A phandle to the syscon node describing UC registers
+
+Example:
+
+	intc: interrupt-controller@f0000040 {
+		compatible = "cnxt,cx92755-ic";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0xf0000040 0x40>;
+		syscon = <&uc_regs>;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
new file mode 100644
index 000000000..8a3c40829
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
@@ -0,0 +1,110 @@
+Specifying interrupt information for devices
+============================================
+
+1) Interrupt client nodes
+-------------------------
+
+Nodes that describe devices which generate interrupts must contain an
+"interrupts" property, an "interrupts-extended" property, or both. If both are
+present, the latter should take precedence; the former may be provided simply
+for compatibility with software that does not recognize the latter. These
+properties contain a list of interrupt specifiers, one per output interrupt. The
+format of the interrupt specifier is determined by the interrupt controller to
+which the interrupts are routed; see section 2 below for details.
+
+  Example:
+	interrupt-parent = <&intc1>;
+	interrupts = <5 0>, <6 0>;
+
+The "interrupt-parent" property is used to specify the controller to which
+interrupts are routed and contains a single phandle referring to the interrupt
+controller node. This property is inherited, so it may be specified in an
+interrupt client node or in any of its parent nodes. Interrupts listed in the
+"interrupts" property are always in reference to the node's interrupt parent.
+
+The "interrupts-extended" property is a special form for use when a node needs
+to reference multiple interrupt parents. Each entry in this property contains
+both the parent phandle and the interrupt specifier. "interrupts-extended"
+should only be used when a device has multiple interrupt parents.
+
+  Example:
+	interrupts-extended = <&intc1 5 1>, <&intc2 1 0>;
+
+2) Interrupt controller nodes
+-----------------------------
+
+A device is marked as an interrupt controller with the "interrupt-controller"
+property. This is a empty, boolean property. An additional "#interrupt-cells"
+property defines the number of cells needed to specify a single interrupt.
+
+It is the responsibility of the interrupt controller's binding to define the
+length and format of the interrupt specifier. The following two variants are
+commonly used:
+
+  a) one cell
+  -----------
+  The #interrupt-cells property is set to 1 and the single cell defines the
+  index of the interrupt within the controller.
+
+  Example:
+
+	vic: intc@10140000 {
+		compatible = "arm,versatile-vic";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x10140000 0x1000>;
+	};
+
+	sic: intc@10003000 {
+		compatible = "arm,versatile-sic";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x10003000 0x1000>;
+		interrupt-parent = <&vic>;
+		interrupts = <31>; /* Cascaded to vic */
+	};
+
+  b) two cells
+  ------------
+  The #interrupt-cells property is set to 2 and the first cell defines the
+  index of the interrupt within the controller, while the second cell is used
+  to specify any of the following flags:
+    - bits[3:0] trigger type and level flags
+        1 = low-to-high edge triggered
+        2 = high-to-low edge triggered
+        4 = active high level-sensitive
+        8 = active low level-sensitive
+
+  Example:
+
+	i2c@7000c000 {
+		gpioext: gpio-adnp@41 {
+			compatible = "ad,gpio-adnp";
+			reg = <0x41>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <160 1>;
+
+			gpio-controller;
+			#gpio-cells = <1>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			nr-gpios = <64>;
+		};
+
+		sx8634@2b {
+			compatible = "smtc,sx8634";
+			reg = <0x2b>;
+
+			interrupt-parent = <&gpioext>;
+			interrupts = <3 0x8>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			threshold = <0x40>;
+			sensitivity = <7>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt
new file mode 100644
index 000000000..aee38e7c1
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/lsi,zevio-intc.txt
@@ -0,0 +1,18 @@
+TI-NSPIRE interrupt controller
+
+Required properties:
+- compatible: Compatible property value should be "lsi,zevio-intc".
+
+- reg: Physical base address of the controller and length of memory mapped
+	region.
+
+- interrupt-controller : Identifies the node as an interrupt controller
+
+Example:
+
+interrupt-controller {
+	compatible = "lsi,zevio-intc";
+	interrupt-controller;
+	reg = <0xDC000000 0x1000>;
+	#interrupt-cells = <1>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-370-xp-mpic.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-370-xp-mpic.txt
new file mode 100644
index 000000000..5fc03134a
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,armada-370-xp-mpic.txt
@@ -0,0 +1,38 @@
+Marvell Armada 370, 375, 38x, XP Interrupt Controller
+-----------------------------------------------------
+
+Required properties:
+- compatible: Should be "marvell,mpic"
+- interrupt-controller: Identifies the node as an interrupt controller.
+- msi-controller: Identifies the node as an PCI Message Signaled
+  Interrupt controller.
+- #interrupt-cells: The number of cells to define the interrupts. Should be 1.
+  The cell is the IRQ number
+
+- reg: Should contain PMIC registers location and length. First pair
+  for the main interrupt registers, second pair for the per-CPU
+  interrupt registers. For this last pair, to be compliant with SMP
+  support, the "virtual" must be use (For the record, these registers
+  automatically map to the interrupt controller registers of the
+  current CPU)
+
+Optional properties:
+
+- interrupts: If defined, then it indicates that this MPIC is
+  connected as a slave to another interrupt controller. This is
+  typically the case on Armada 375 and Armada 38x, where the MPIC is
+  connected as a slave to the Cortex-A9 GIC. The provided interrupt
+  indicate to which GIC interrupt the MPIC output is connected.
+
+Example:
+
+        mpic: interrupt-controller@d0020000 {
+              compatible = "marvell,mpic";
+              #interrupt-cells = <1>;
+              #address-cells = <1>;
+              #size-cells = <1>;
+              interrupt-controller;
+              msi-controller;
+              reg = <0xd0020a00 0x1d0>,
+                    <0xd0021070 0x58>;
+        };
diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,orion-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,orion-intc.txt
new file mode 100644
index 000000000..2c11ac76f
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,orion-intc.txt
@@ -0,0 +1,48 @@
+Marvell Orion SoC interrupt controllers
+
+* Main interrupt controller
+
+Required properties:
+- compatible: shall be "marvell,orion-intc"
+- reg: base address(es) of interrupt registers starting with CAUSE register
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: number of cells to encode an interrupt source, shall be 1
+
+The interrupt sources map to the corresponding bits in the interrupt
+registers, i.e.
+- 0 maps to bit 0 of first base address,
+- 1 maps to bit 1 of first base address,
+- 32 maps to bit 0 of second base address, and so on.
+
+Example:
+	intc: interrupt-controller {
+		compatible = "marvell,orion-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		 /* Dove has 64 first level interrupts */
+		reg = <0x20200 0x10>, <0x20210 0x10>;
+	};
+
+* Bridge interrupt controller
+
+Required properties:
+- compatible: shall be "marvell,orion-bridge-intc"
+- reg: base address of bridge interrupt registers starting with CAUSE register
+- interrupts: bridge interrupt of the main interrupt controller
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: number of cells to encode an interrupt source, shall be 1
+
+Optional properties:
+- marvell,#interrupts: number of interrupts provided by bridge interrupt
+      controller, defaults to 32 if not set
+
+Example:
+	bridge_intc: interrupt-controller {
+		compatible = "marvell,orion-bridge-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x20110 0x8>;
+		interrupts = <0>;
+		/* Dove bridge provides 5 interrupts */
+		marvell,#interrupts = <5>;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt
new file mode 100644
index 000000000..aae4c384e
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt
@@ -0,0 +1,60 @@
+MIPS Global Interrupt Controller (GIC)
+
+The MIPS GIC routes external interrupts to individual VPEs and IRQ pins.
+It also supports local (per-processor) interrupts and software-generated
+interrupts which can be used as IPIs.  The GIC also includes a free-running
+global timer, per-CPU count/compare timers, and a watchdog.
+
+Required properties:
+- compatible : Should be "mti,gic".
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt specifier.  Should be 3.
+  - The first cell is the type of interrupt, local or shared.
+    See <include/dt-bindings/interrupt-controller/mips-gic.h>.
+  - The second cell is the GIC interrupt number.
+  - The third cell encodes the interrupt flags.
+    See <include/dt-bindings/interrupt-controller/irq.h> for a list of valid
+    flags.
+
+Optional properties:
+- reg : Base address and length of the GIC registers.  If not present,
+  the base address reported by the hardware GCR_GIC_BASE will be used.
+- mti,reserved-cpu-vectors : Specifies the list of CPU interrupt vectors
+  to which the GIC may not route interrupts.  Valid values are 2 - 7.
+  This property is ignored if the CPU is started in EIC mode.
+
+Required properties for timer sub-node:
+- compatible : Should be "mti,gic-timer".
+- interrupts : Interrupt for the GIC local timer.
+
+Optional properties for timer sub-node:
+- clocks : GIC timer operating clock.
+- clock-frequency : Clock frequency at which the GIC timers operate.
+
+Note that one of clocks or clock-frequency must be specified.
+
+Example:
+
+	gic: interrupt-controller@1bdc0000 {
+		compatible = "mti,gic";
+		reg = <0x1bdc0000 0x20000>;
+
+		interrupt-controller;
+		#interrupt-cells = <3>;
+
+		mti,reserved-cpu-vectors = <7>;
+
+		timer {
+			compatible = "mti,gic-timer";
+			interrupts = <GIC_LOCAL 1 IRQ_TYPE_NONE>;
+			clock-frequency = <50000000>;
+		};
+	};
+
+	uart@18101400 {
+		...
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SHARED 24 IRQ_TYPE_LEVEL_HIGH>;
+		...
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt
new file mode 100644
index 000000000..1099fe078
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra-ictlr.txt
@@ -0,0 +1,43 @@
+NVIDIA Legacy Interrupt Controller
+
+All Tegra SoCs contain a legacy interrupt controller that routes
+interrupts to the GIC, and also serves as a wakeup source. It is also
+referred to as "ictlr", hence the name of the binding.
+
+The HW block exposes a number of interrupt controllers, each
+implementing a set of 32 interrupts.
+
+Required properties:
+
+- compatible : should be: "nvidia,tegra<chip>-ictlr". The LIC on
+  subsequent SoCs remained backwards-compatible with Tegra30, so on
+  Tegra generations later than Tegra30 the compatible value should
+  include "nvidia,tegra30-ictlr".	
+- reg : Specifies base physical address and size of the registers.
+  Each controller must be described separately (Tegra20 has 4 of them,
+  whereas Tegra30 and later have 5"  
+- interrupt-controller : Identifies the node as an interrupt controller.
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value must be 3.
+- interrupt-parent : a phandle to the GIC these interrupts are routed
+  to.
+
+Notes:
+
+- Because this HW ultimately routes interrupts to the GIC, the
+  interrupt specifier must be that of the GIC.
+- Only SPIs can use the ictlr as an interrupt parent. SGIs and PPIs
+  are explicitly forbidden.
+
+Example:
+
+	ictlr: interrupt-controller@60004000 {
+		compatible = "nvidia,tegra20-ictlr", "nvidia,tegra-ictlr";
+		reg = <0x60004000 64>,
+		      <0x60004100 64>,
+		      <0x60004200 64>,
+		      <0x60004300 64>;
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		interrupt-parent = <&intc>;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/opencores,or1k-pic.txt b/Documentation/devicetree/bindings/interrupt-controller/opencores,or1k-pic.txt
new file mode 100644
index 000000000..55c04faa3
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/opencores,or1k-pic.txt
@@ -0,0 +1,23 @@
+OpenRISC 1000 Programmable Interrupt Controller
+
+Required properties:
+
+- compatible : should be "opencores,or1k-pic-level" for variants with
+  level triggered interrupt lines, "opencores,or1k-pic-edge" for variants with
+  edge triggered interrupt lines or "opencores,or1200-pic" for machines
+  with the non-spec compliant or1200 type implementation.
+
+  "opencores,or1k-pic" is also provided as an alias to "opencores,or1200-pic",
+  but this is only for backwards compatibility.
+
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 1.
+
+Example:
+
+intc: interrupt-controller {
+	compatible = "opencores,or1k-pic-level";
+	interrupt-controller;
+	#interrupt-cells = <1>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt
new file mode 100644
index 000000000..4f7946ae8
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt
@@ -0,0 +1,27 @@
+DT bindings for the R-/SH-Mobile irqpin controller
+
+Required properties:
+
+- compatible: has to be "renesas,intc-irqpin-<soctype>", "renesas,intc-irqpin"
+  as fallback.
+  Examples with soctypes are:
+    - "renesas,intc-irqpin-r8a7740" (R-Mobile A1)
+    - "renesas,intc-irqpin-r8a7778" (R-Car M1A)
+    - "renesas,intc-irqpin-r8a7779" (R-Car H1)
+    - "renesas,intc-irqpin-sh73a0" (SH-Mobile AG5)
+
+- reg: Base address and length of each register bank used by the external
+  IRQ pins driven by the interrupt controller hardware module. The base
+  addresses, length and number of required register banks varies with soctype.
+
+- #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in
+  interrupts.txt in this directory
+
+Optional properties:
+
+- any properties, listed in interrupts.txt, and any standard resource allocation
+  properties
+- sense-bitfield-width: width of a single sense bitfield in the SENSE register,
+  if different from the default 4 bits
+- control-parent: disable and enable interrupts on the parent interrupt
+  controller, needed for some broken implementations
diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt
new file mode 100644
index 000000000..63633bdea
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt
@@ -0,0 +1,34 @@
+DT bindings for the R-Mobile/R-Car interrupt controller
+
+Required properties:
+
+- compatible: has to be "renesas,irqc-<soctype>", "renesas,irqc" as fallback.
+  Examples with soctypes are:
+    - "renesas,irqc-r8a73a4" (R-Mobile APE6)
+    - "renesas,irqc-r8a7790" (R-Car H2)
+    - "renesas,irqc-r8a7791" (R-Car M2-W)
+    - "renesas,irqc-r8a7792" (R-Car V2H)
+    - "renesas,irqc-r8a7793" (R-Car M2-N)
+    - "renesas,irqc-r8a7794" (R-Car E2)
+- #interrupt-cells: has to be <2>: an interrupt index and flags, as defined in
+  interrupts.txt in this directory
+- clocks: Must contain a reference to the functional clock.
+
+Optional properties:
+
+- any properties, listed in interrupts.txt, and any standard resource allocation
+  properties
+
+Example:
+
+	irqc0: interrupt-controller@e61c0000 {
+		compatible = "renesas,irqc-r8a7790", "renesas,irqc";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		reg = <0 0xe61c0000 0 0x200>;
+		interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 1 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 2 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 3 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp4_clks R8A7790_CLK_IRQC>;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/samsung,s3c24xx-irq.txt b/Documentation/devicetree/bindings/interrupt-controller/samsung,s3c24xx-irq.txt
new file mode 100644
index 000000000..c54c5a9a2
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/samsung,s3c24xx-irq.txt
@@ -0,0 +1,53 @@
+Samsung S3C24XX Interrupt Controllers
+
+The S3C24XX SoCs contain a custom set of interrupt controllers providing a
+varying number of interrupt sources. The set consists of a main- and sub-
+controller and on newer SoCs even a second main controller.
+
+Required properties:
+- compatible: Compatible property value should be "samsung,s3c2410-irq"
+  for machines before s3c2416 and "samsung,s3c2416-irq" for s3c2416 and later.
+
+- reg: Physical base address of the controller and length of memory mapped
+  region.
+
+- interrupt-controller : Identifies the node as an interrupt controller
+
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 4 and interrupt descriptor shall
+  have the following format:
+      <ctrl_num parent_irq ctrl_irq type>
+
+  ctrl_num contains the controller to use:
+      - 0 ... main controller
+      - 1 ... sub controller
+      - 2 ... second main controller on s3c2416 and s3c2450
+  parent_irq contains the parent bit in the main controller and will be
+             ignored in main controllers
+  ctrl_irq contains the interrupt bit of the controller
+  type contains the trigger type to use
+
+Example:
+
+	interrupt-controller@4a000000 {
+		compatible = "samsung,s3c2410-irq";
+		reg = <0x4a000000 0x100>;
+		interrupt-controller;
+		#interrupt-cells=<4>;
+	};
+
+	[...]
+
+	serial@50000000 {
+		compatible = "samsung,s3c2410-uart";
+		reg = <0x50000000 0x4000>;
+		interrupt-parent = <&subintc>;
+		interrupts = <1 28 0 4>, <1 28 1 4>;
+	};
+
+	rtc@57000000 {
+		compatible = "samsung,s3c2410-rtc";
+		reg = <0x57000000 0x100>;
+		interrupt-parent = <&intc>;
+		interrupts = <0 30 0 3>, <0 8 0 3>;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/snps,dw-apb-ictl.txt b/Documentation/devicetree/bindings/interrupt-controller/snps,dw-apb-ictl.txt
new file mode 100644
index 000000000..492911744
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/snps,dw-apb-ictl.txt
@@ -0,0 +1,32 @@
+Synopsys DesignWare APB interrupt controller (dw_apb_ictl)
+
+Synopsys DesignWare provides interrupt controller IP for APB known as
+dw_apb_ictl. The IP is used as secondary interrupt controller in some SoCs with
+APB bus, e.g. Marvell Armada 1500.
+
+Required properties:
+- compatible: shall be "snps,dw-apb-ictl"
+- reg: physical base address of the controller and length of memory mapped
+  region starting with ENABLE_LOW register
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: number of cells to encode an interrupt-specifier, shall be 1
+- interrupts: interrupt reference to primary interrupt controller
+- interrupt-parent: (optional) reference specific primary interrupt controller
+
+The interrupt sources map to the corresponding bits in the interrupt
+registers, i.e.
+- 0 maps to bit 0 of low interrupts,
+- 1 maps to bit 1 of low interrupts,
+- 32 maps to bit 0 of high interrupts,
+- 33 maps to bit 1 of high interrupts,
+- (optional) fast interrupts start at 64.
+
+Example:
+	aic: interrupt-controller@3000 {
+		compatible = "snps,dw-apb-ictl";
+		reg = <0x3000 0xc00>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,sti-irq-syscfg.txt b/Documentation/devicetree/bindings/interrupt-controller/st,sti-irq-syscfg.txt
new file mode 100644
index 000000000..ced601406
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/st,sti-irq-syscfg.txt
@@ -0,0 +1,35 @@
+STMicroelectronics STi System Configuration Controlled IRQs
+-----------------------------------------------------------
+
+On STi based systems; External, CTI (Core Sight), PMU (Performance Management),
+and PL310 L2 Cache IRQs are controlled using System Configuration registers.
+This driver is used to unmask them prior to use.
+
+Required properties:
+- compatible	: Should be set to one of:
+			"st,stih415-irq-syscfg"
+			"st,stih416-irq-syscfg"
+			"st,stih407-irq-syscfg"
+			"st,stid127-irq-syscfg"
+- st,syscfg	: Phandle to Cortex-A9 IRQ system config registers
+- st,irq-device	: Array of IRQs to enable - should be 2 in length
+- st,fiq-device	: Array of FIQs to enable - should be 2 in length
+
+Optional properties:
+- st,invert-ext	: External IRQs can be inverted at will.  This property inverts
+		  these IRQs using bitwise logic.  A number of defines have been
+		  provided for convenience:
+			ST_IRQ_SYSCFG_EXT_1_INV
+			ST_IRQ_SYSCFG_EXT_2_INV
+			ST_IRQ_SYSCFG_EXT_3_INV
+Example:
+
+irq-syscfg {
+	compatible    = "st,stih416-irq-syscfg";
+	st,syscfg     = <&syscfg_cpu>;
+	st,irq-device = <ST_IRQ_SYSCFG_PMU_0>,
+			<ST_IRQ_SYSCFG_PMU_1>;
+	st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>,
+			<ST_IRQ_SYSCFG_DISABLED>;
+	st,invert-ext = <(ST_IRQ_SYSCFG_EXT_1_INV | ST_IRQ_SYSCFG_EXT_3_INV)>;
+};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt
new file mode 100644
index 000000000..d9bb106bd
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/ti,keystone-irq.txt
@@ -0,0 +1,36 @@
+Keystone 2 IRQ controller IP
+
+On Keystone SOCs, DSP cores can send interrupts to ARM
+host using the IRQ controller IP. It provides 28 IRQ signals to ARM.
+The IRQ handler running on HOST OS can identify DSP signal source by
+analyzing SRCCx bits in IPCARx registers. This is one of the component
+used by the IPC mechanism used on Keystone SOCs.
+
+Required Properties:
+- compatible: should be "ti,keystone-irq"
+- ti,syscon-dev : phandle and offset pair. The phandle to syscon used to
+			access device control registers and the offset inside
+			device control registers range.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode interrupt
+					 source should be 1.
+- interrupts: interrupt reference to primary interrupt controller
+
+Please refer to interrupts.txt in this directory for details of the common
+Interrupt Controllers bindings used by client devices.
+
+Example:
+	kirq0: keystone_irq0@026202a0 {
+		compatible = "ti,keystone-irq";
+		ti,syscon-dev = <&devctrl 0x2a0>;
+		interrupts = <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+
+	dsp0: dsp0 {
+		compatible = "linux,rproc-user";
+		...
+		interrupt-parent = <&kirq0>;
+		interrupts = <10 2>;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,omap-intc-irq.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,omap-intc-irq.txt
new file mode 100644
index 000000000..38ce5d037
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/ti,omap-intc-irq.txt
@@ -0,0 +1,28 @@
+Omap2/3 intc controller
+
+On TI omap2 and 3 the intc interrupt controller can provide
+96 or 128 IRQ signals to the ARM host depending on the SoC.
+
+Required Properties:
+- compatible: should be one of
+			"ti,omap2-intc"
+			"ti,omap3-intc"
+			"ti,dm814-intc"
+			"ti,dm816-intc"
+			"ti,am33xx-intc"
+
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode interrupt
+		     source, should be 1 for intc
+- interrupts: interrupt reference to primary interrupt controller
+
+Please refer to interrupts.txt in this directory for details of the common
+Interrupt Controllers bindings used by client devices.
+
+Example:
+	intc: interrupt-controller@48200000 {
+		compatible = "ti,omap3-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x48200000 0x1000>;
+	};
diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu b/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu
new file mode 100644
index 000000000..43effa0a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/ti,omap4-wugen-mpu
@@ -0,0 +1,33 @@
+TI OMAP4 Wake-up Generator
+
+All TI OMAP4/5 (and their derivatives) an interrupt controller that
+routes interrupts to the GIC, and also serves as a wakeup source. It
+is also referred to as "WUGEN-MPU", hence the name of the binding.
+
+Reguired properties:
+
+- compatible : should contain at least "ti,omap4-wugen-mpu" or
+  "ti,omap5-wugen-mpu"
+- reg : Specifies base physical address and size of the registers.
+- interrupt-controller : Identifies the node as an interrupt controller.
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value must be 3.
+- interrupt-parent : a phandle to the GIC these interrupts are routed
+  to.
+
+Notes:
+
+- Because this HW ultimately routes interrupts to the GIC, the
+  interrupt specifier must be that of the GIC.
+- Only SPIs can use the WUGEN as an interrupt parent. SGIs and PPIs
+  are explicitly forbiden.
+
+Example:
+
+       wakeupgen: interrupt-controller@48281000 {
+               compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
+               interrupt-controller;
+               #interrupt-cells = <3>;
+               reg = <0x48281000 0x1000>;
+               interrupt-parent = <&gic>;
+       };