Initial import

11 files changed, 488 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/media/i2c/adv7343.txt b/Documentation/devicetree/bindings/media/i2c/adv7343.txt
new file mode 100644
index 000000000..5653bc242
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7343.txt
@@ -0,0 +1,48 @@
+* Analog Devices adv7343 video encoder
+
+The ADV7343 are high speed, digital-to-analog video encoders in a 64-lead LQFP
+package. Six high speed, 3.3 V, 11-bit video DACs provide support for composite
+(CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in standard
+definition (SD), enhanced definition (ED), or high definition (HD) video
+formats.
+
+Required Properties :
+- compatible: Must be "adi,adv7343"
+
+Optional Properties :
+- adi,power-mode-sleep-mode: on enable the current consumption is reduced to
+			      micro ampere level. All DACs and the internal PLL
+			      circuit are disabled.
+- adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows
+			   internal PLL 1 circuit to be powered down and the
+			   oversampling to be switched off.
+- ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6,
+			      0 = OFF and 1 = ON, Default value when this
+			      property is not specified is <0 0 0 0 0 0>.
+- ad,adv7343-sd-config-dac-out: array configure SD DAC Output's 1 and 2, 0 = OFF
+				 and 1 = ON, Default value when this property is
+				 not specified is <0 0>.
+
+Example:
+
+i2c0@1c22000 {
+	...
+	...
+
+	adv7343@2a {
+		compatible = "adi,adv7343";
+		reg = <0x2a>;
+
+		port {
+			adv7343_1: endpoint {
+					adi,power-mode-sleep-mode;
+					adi,power-mode-pll-ctrl;
+					/* Use DAC1..3, DAC6 */
+					adi,dac-enable = <1 1 1 0 0 1>;
+					/* Use SD DAC output 1 */
+					adi,sd-dac-enable = <1 0>;
+			};
+		};
+	};
+	...
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
new file mode 100644
index 000000000..c27cede3b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
@@ -0,0 +1,70 @@
+* Analog Devices ADV7604/11 video decoder with HDMI receiver
+
+The ADV7604 and ADV7611 are multiformat video decoders with an integrated HDMI
+receiver. The ADV7604 has four multiplexed HDMI inputs and one analog input,
+and the ADV7611 has one HDMI input and no analog input.
+
+These device tree bindings support the ADV7611 only at the moment.
+
+Required Properties:
+
+  - compatible: Must contain one of the following
+    - "adi,adv7611" for the ADV7611
+
+  - reg: I2C slave address
+
+  - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
+    detection pins, one per HDMI input. The active flag indicates the GPIO
+    level that enables hot-plug detection.
+
+The device node must contain one 'port' child node per device input and output
+port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows.
+
+  Port			ADV7611
+------------------------------------------------------------
+  HDMI			0
+  Digital output	1
+
+The digital output port node must contain at least one endpoint.
+
+Optional Properties:
+
+  - reset-gpios: Reference to the GPIO connected to the device's reset pin.
+
+Optional Endpoint Properties:
+
+  The following three properties are defined in video-interfaces.txt and are
+  valid for source endpoints only.
+
+  - hsync-active: Horizontal synchronization polarity. Defaults to active low.
+  - vsync-active: Vertical synchronization polarity. Defaults to active low.
+  - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge.
+
+  If none of hsync-active, vsync-active and pclk-sample is specified the
+  endpoint will use embedded BT.656 synchronization.
+
+
+Example:
+
+	hdmi_receiver@4c {
+		compatible = "adi,adv7611";
+		reg = <0x4c>;
+
+		reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
+		hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+		};
+		port@1 {
+			reg = <1>;
+			hdmi_in: endpoint {
+				remote-endpoint = <&ccdc_in>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt
new file mode 100644
index 000000000..ed5a334b1
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt
@@ -0,0 +1,28 @@
+Micron 1.3Mp CMOS Digital Image Sensor
+
+The Micron MT9M111 is a CMOS active pixel digital image sensor with an active
+array size of 1280H x 1024V. It is programmable through a simple two-wire serial
+interface.
+
+Required Properties:
+- compatible: value should be "micron,mt9m111"
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c_master {
+		mt9m111@5d {
+			compatible = "micron,mt9m111";
+			reg = <0x5d>;
+
+			remote = <&pxa_camera>;
+			port {
+				mt9m111_1: endpoint {
+					bus-width = <8>;
+					remote-endpoint = <&pxa_camera>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9p031.txt b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt
new file mode 100644
index 000000000..cb60443ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt
@@ -0,0 +1,40 @@
+* Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor
+
+The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor with
+an active array size of 2592H x 1944V. It is programmable through a simple
+two-wire serial interface.
+
+Required Properties:
+- compatible: value should be either one among the following
+	(a) "aptina,mt9p031" for mt9p031 sensor
+	(b) "aptina,mt9p031m" for mt9p031m sensor
+
+- input-clock-frequency: Input clock frequency.
+
+- pixel-clock-frequency: Pixel clock frequency.
+
+Optional Properties:
+- reset-gpios: Chip reset GPIO
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		mt9p031@5d {
+			compatible = "aptina,mt9p031";
+			reg = <0x5d>;
+			reset-gpios = <&gpio3 30 0>;
+
+			port {
+				mt9p031_1: endpoint {
+					input-clock-frequency = <6000000>;
+					pixel-clock-frequency = <96000000>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt
new file mode 100644
index 000000000..202565313
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt
@@ -0,0 +1,39 @@
+* Aptina 1/3-Inch WVGA CMOS Digital Image Sensor
+
+The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with
+an active array size of 752H x 480V. It is programmable through a simple
+two-wire serial interface.
+
+Required Properties:
+
+- compatible: value should be either one among the following
+	(a) "aptina,mt9v022" for MT9V022 color sensor
+	(b) "aptina,mt9v022m" for MT9V022 monochrome sensor
+	(c) "aptina,mt9v024" for MT9V024 color sensor
+	(d) "aptina,mt9v024m" for MT9V024 monochrome sensor
+	(e) "aptina,mt9v032" for MT9V032 color sensor
+	(f) "aptina,mt9v032m" for MT9V032 monochrome sensor
+	(g) "aptina,mt9v034" for MT9V034 color sensor
+	(h) "aptina,mt9v034m" for MT9V034 monochrome sensor
+
+Optional Properties:
+
+- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
+	expressed as a 64-bit big-endian integer.
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	mt9v032@5c {
+		compatible = "aptina,mt9v032";
+		reg = <0x5c>;
+
+		port {
+			mt9v032_out: endpoint {
+				link-frequencies = /bits/ 64
+					<13000000 26600000 27000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt
new file mode 100644
index 000000000..855e1faf7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt
@@ -0,0 +1,63 @@
+SMIA/SMIA++ sensor
+
+SMIA (Standard Mobile Imaging Architecture) is an image sensor standard
+defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension
+of that. These definitions are valid for both types of sensors.
+
+More detailed documentation can be found in
+Documentation/devicetree/bindings/media/video-interfaces.txt .
+
+
+Mandatory properties
+--------------------
+
+- compatible: "nokia,smia"
+- reg: I2C address (0x10, or an alternative address)
+- vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor
+  dependent).
+- clocks: External clock to the sensor
+- clock-frequency: Frequency of the external clock to the sensor
+- link-frequencies: List of allowed data link frequencies. An array of
+  64-bit elements.
+
+
+Optional properties
+-------------------
+
+- nokia,nvm-size: The size of the NVM, in bytes. If the size is not given,
+  the NVM contents will not be read.
+- reset-gpios: XSHUTDOWN GPIO
+
+
+Endpoint node mandatory properties
+----------------------------------
+
+- clock-lanes: <0>
+- data-lanes: <1..n>
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+
+Example
+-------
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	smiapp_1: camera@10 {
+		compatible = "nokia,smia";
+		reg = <0x10>;
+		reset-gpios = <&gpio3 20 0>;
+		vana-supply = <&vaux3>;
+		clocks = <&omap3_isp 0>;
+		clock-frequency = <9600000>;
+		nokia,nvm-size = <512>; /* 8 * 64 */
+		link-frequencies = /bits/ 64 <199200000 210000000 499200000>;
+		port {
+			smiapp_1_1: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&csi2a_ep>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2640.txt b/Documentation/devicetree/bindings/media/i2c/ov2640.txt
new file mode 100644
index 000000000..c429b5bdc
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2640.txt
@@ -0,0 +1,46 @@
+* Omnivision OV2640 CMOS sensor
+
+The Omnivision OV2640 sensor support multiple resolutions output, such as
+CIF, SVGA, UXGA. It also can support YUV422/420, RGB565/555 or raw RGB
+output format.
+
+Required Properties:
+- compatible: should be "ovti,ov2640"
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+
+Optional Properties:
+- resetb-gpios: reference to the GPIO connected to the resetb pin, if any.
+- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c1: i2c@f0018000 {
+		ov2640: camera@0x30 {
+			compatible = "ovti,ov2640";
+			reg = <0x30>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pck1 &pinctrl_ov2640_pwdn &pinctrl_ov2640_resetb>;
+
+			resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
+			pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+
+			clocks = <&pck1>;
+			clock-names = "xvclk";
+
+			assigned-clocks = <&pck1>;
+			assigned-clock-rates = <25000000>;
+
+			port {
+				ov2640_0: endpoint {
+					remote-endpoint = <&isi_0>;
+					bus-width = <8>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2659.txt b/Documentation/devicetree/bindings/media/i2c/ov2659.txt
new file mode 100644
index 000000000..cabc7d827
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2659.txt
@@ -0,0 +1,38 @@
+* OV2659 1/5-Inch 2Mp SOC Camera
+
+The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of
+1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports
+multiple resolutions output, such as UXGA, SVGA, 720p. It also can support
+YUV422, RGB565/555 or raw RGB output formats.
+
+Required Properties:
+- compatible: Must be "ovti,ov2659"
+- reg: I2C slave address
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+- link-frequencies: target pixel clock frequency.
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		 ov2659@30 {
+			compatible = "ovti,ov2659";
+			reg = <0x30>;
+
+			clocks = <&clk_ov2659 0>;
+			clock-names = "xvclk";
+
+			port {
+				ov2659_0: endpoint {
+					remote-endpoint = <&vpfe_ep>;
+					link-frequencies = /bits/ 64 <70000000>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ths8200.txt b/Documentation/devicetree/bindings/media/i2c/ths8200.txt
new file mode 100644
index 000000000..285f6ae7d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ths8200.txt
@@ -0,0 +1,19 @@
+* Texas Instruments THS8200 video encoder
+
+The ths8200 device is a digital to analog converter used in DVD players, video
+recorders, set-top boxes.
+
+Required Properties :
+- compatible : value must be "ti,ths8200"
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		ths8200@5c {
+			compatible = "ti,ths8200";
+			reg = <0x5c>;
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp514x.txt b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt
new file mode 100644
index 000000000..46752cc71
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt
@@ -0,0 +1,44 @@
+* Texas Instruments TVP514x video decoder
+
+The TVP5146/TVP5146m2/TVP5147/TVP5147m1 device is high quality, single-chip
+digital video decoder that digitizes and decodes all popular baseband analog
+video formats into digital video component. The tvp514x decoder supports analog-
+to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D
+conversion and decoding of NTSC, PAL and SECAM composite and S-video into
+component YCbCr.
+
+Required Properties :
+- compatible : value should be either one among the following
+	(a) "ti,tvp5146" for tvp5146 decoder.
+	(b) "ti,tvp5146m2" for tvp5146m2 decoder.
+	(c) "ti,tvp5147" for tvp5147 decoder.
+	(d) "ti,tvp5147m1" for tvp5147m1 decoder.
+
+- hsync-active: HSYNC Polarity configuration for endpoint.
+
+- vsync-active: VSYNC Polarity configuration for endpoint.
+
+- pclk-sample: Clock polarity of the endpoint.
+
+For further reading on port node refer to Documentation/devicetree/bindings/
+media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		tvp514x@5c {
+			compatible = "ti,tvp5146";
+			reg = <0x5c>;
+
+			port {
+				tvp514x_1: endpoint {
+					hsync-active = <1>;
+					vsync-active = <1>;
+					pclk-sample = <0>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp7002.txt b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
new file mode 100644
index 000000000..5f28b5d9a
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
@@ -0,0 +1,53 @@
+* Texas Instruments TV7002 video decoder
+
+The TVP7002 device supports digitizing of video and graphics signal in RGB and
+YPbPr color space.
+
+Required Properties :
+- compatible : Must be "ti,tvp7002"
+
+Optional Properties:
+- hsync-active: HSYNC Polarity configuration for the bus. Default value when
+  this property is not specified is <0>.
+
+- vsync-active: VSYNC Polarity configuration for the bus. Default value when
+  this property is not specified is <0>.
+
+- pclk-sample: Clock polarity of the bus. Default value when this property is
+  not specified is <0>.
+
+- sync-on-green-active: Active state of Sync-on-green signal property of the
+  endpoint.
+  0 = Normal Operation (Active Low, Default)
+  1 = Inverted operation
+
+- field-even-active: Active-high Field ID output polarity control of the bus.
+  Under normal operation, the field ID output is set to logic 1 for an odd field
+  (field 1) and set to logic 0 for an even field (field 0).
+  0 = Normal Operation (Active Low, Default)
+  1 = FID output polarity inverted
+
+For further reading of port node refer Documentation/devicetree/bindings/media/
+video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		tvp7002@5c {
+			compatible = "ti,tvp7002";
+			reg = <0x5c>;
+
+			port {
+				tvp7002_1: endpoint {
+					hsync-active = <1>;
+					vsync-active = <1>;
+					pclk-sample = <0>;
+					sync-on-green-active = <1>;
+					field-even-active = <0>;
+				};
+			};
+		};
+		...
+	};