diff options
| author | André Fabian Silva Delgado <emulatorman@parabola.nu> | 2015-08-05 17:04:01 -0300 |
|---|---|---|
| committer | André Fabian Silva Delgado <emulatorman@parabola.nu> | 2015-08-05 17:04:01 -0300 |
| commit | 57f0f512b273f60d52568b8c6b77e17f5636edc0 (patch) | |
| tree | 5e910f0e82173f4ef4f51111366a3f1299037a7b /Documentation/devicetree/bindings/media | |
Initial import
Diffstat (limited to 'Documentation/devicetree/bindings/media')
41 files changed, 2140 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/media/atmel-isi.txt b/Documentation/devicetree/bindings/media/atmel-isi.txt new file mode 100644 index 000000000..251f008f2 --- /dev/null +++ b/Documentation/devicetree/bindings/media/atmel-isi.txt @@ -0,0 +1,51 @@ +Atmel Image Sensor Interface (ISI) SoC Camera Subsystem +---------------------------------------------- + +Required properties: +- compatible: must be "atmel,at91sam9g45-isi" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the ISI; +- clocks: list of clock specifiers, corresponding to entries in + the clock-names property; +- clock-names: must contain "isi_clk", which is the isi peripherial clock. + +ISI supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + isi: isi@f0034000 { + compatible = "atmel,at91sam9g45-isi"; + reg = <0xf0034000 0x4000>; + interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; + + clocks = <&isi_clk>; + clock-names = "isi_clk"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + isi_0: endpoint { + remote-endpoint = <&ov2640_0>; + bus-width = <8>; + }; + }; + }; + + i2c1: i2c@f0018000 { + ov2640: camera@0x30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/coda.txt b/Documentation/devicetree/bindings/media/coda.txt new file mode 100644 index 000000000..2865d04e4 --- /dev/null +++ b/Documentation/devicetree/bindings/media/coda.txt @@ -0,0 +1,30 @@ +Chips&Media Coda multi-standard codec IP +======================================== + +Coda codec IPs are present in i.MX SoCs in various versions, +called VPU (Video Processing Unit). + +Required properties: +- compatible : should be "fsl,<chip>-src" for i.MX SoCs: + (a) "fsl,imx27-vpu" for CodaDx6 present in i.MX27 + (b) "fsl,imx53-vpu" for CODA7541 present in i.MX53 + (c) "fsl,imx6q-vpu" for CODA960 present in i.MX6q +- reg: should be register base and length as documented in the + SoC reference manual +- interrupts : Should contain the VPU interrupt. For CODA960, + a second interrupt is needed for the MJPEG unit. +- clocks : Should contain the ahb and per clocks, in the order + determined by the clock-names property. +- clock-names : Should be "ahb", "per" +- iram : phandle pointing to the SRAM device node + +Example: + +vpu: vpu@63ff4000 { + compatible = "fsl,imx53-vpu"; + reg = <0x63ff4000 0x1000>; + interrupts = <9>; + clocks = <&clks 63>, <&clks 63>; + clock-names = "ahb", "per"; + iram = <&ocram>; +}; diff --git a/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt b/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt new file mode 100644 index 000000000..0bf6fb7fb --- /dev/null +++ b/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt @@ -0,0 +1,16 @@ +Exynos4x12/Exynos5 SoC series camera host interface (FIMC-LITE) + +Required properties: + +- compatible : should be one of: + "samsung,exynos4212-fimc-lite" for Exynos4212/4412 SoCs, + "samsung,exynos5250-fimc-lite" for Exynos5250 compatible + devices; +- reg : physical base address and size of the device memory mapped + registers; +- interrupts : should contain FIMC-LITE interrupt; +- clocks : FIMC LITE gate clock should be specified in this property. +- clock-names : should contain "flite" entry. + +Each FIMC device should have an alias in the aliases node, in the form of +fimc-lite<n>, where <n> is an integer specifying the IP block instance. diff --git a/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt new file mode 100644 index 000000000..4ef45636e --- /dev/null +++ b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt @@ -0,0 +1,15 @@ +Samsung S5P/EXYNOS SoC series JPEG codec + +Required properties: + +- compatible : should be one of: + "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg", + "samsung,exynos3250-jpeg", "samsung,exynos5420-jpeg"; +- reg : address and length of the JPEG codec IP register set; +- interrupts : specifies the JPEG codec IP interrupt; +- clock-names : should contain: + - "jpeg" for the core gate clock, + - "sclk" for the special clock (optional). +- clocks : should contain the clock specifier and clock ID list + matching entries in the clock-names property; from + the common clock bindings. diff --git a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt new file mode 100644 index 000000000..55c9ad6f9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt @@ -0,0 +1,49 @@ +Exynos4x12 SoC series Imaging Subsystem (FIMC-IS) + +The FIMC-IS is a subsystem for processing image signal from an image sensor. +The Exynos4x12 SoC series FIMC-IS V1.5 comprises of a dedicated ARM Cortex-A5 +processor, ISP, DRC and FD IP blocks and peripheral devices such as UART, I2C +and SPI bus controllers, PWM and ADC. + +fimc-is node +------------ + +Required properties: +- compatible : should be "samsung,exynos4212-fimc-is" for Exynos4212 and + Exynos4412 SoCs; +- reg : physical base address and length of the registers set; +- interrupts : must contain two FIMC-IS interrupts, in order: ISP0, ISP1; +- clocks : list of clock specifiers, corresponding to entries in + clock-names property; +- clock-names : must contain "ppmuispx", "ppmuispx", "lite0", "lite1" + "mpll", "sysreg", "isp", "drc", "fd", "mcuisp", "uart", + "ispdiv0", "ispdiv1", "mcuispdiv0", "mcuispdiv1", "aclk200", + "div_aclk200", "aclk400mcuisp", "div_aclk400mcuisp" entries, + matching entries in the clocks property. +pmu subnode +----------- + +Required properties: + - reg : must contain PMU physical base address and size of the register set. + +The following are the FIMC-IS peripheral device nodes and can be specified +either standalone or as the fimc-is node child nodes. + +i2c-isp (ISP I2C bus controller) nodes +------------------------------------------ + +Required properties: + +- compatible : should be "samsung,exynos4212-i2c-isp" for Exynos4212 and + Exynos4412 SoCs; +- reg : physical base address and length of the registers set; +- clocks : must contain gate clock specifier for this controller; +- clock-names : must contain "i2c_isp" entry. + +For the above nodes it is required to specify a pinctrl state named "default", +according to the pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt. + +Device tree nodes of the image sensors' controlled directly by the FIMC-IS +firmware must be child nodes of their corresponding ISP I2C bus controller node. +The data link of these image sensors must be specified using the common video +interfaces bindings, defined in video-interfaces.txt. diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt new file mode 100644 index 000000000..0604d42f3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/exynos5-gsc.txt @@ -0,0 +1,30 @@ +* Samsung Exynos5 G-Scaler device + +G-Scaler is used for scaling and color space conversion on EXYNOS5 SoCs. + +Required properties: +- compatible: should be "samsung,exynos5-gsc" +- reg: should contain G-Scaler physical address location and length. +- interrupts: should contain G-Scaler interrupt number + +Example: + +gsc_0: gsc@0x13e00000 { + compatible = "samsung,exynos5-gsc"; + reg = <0x13e00000 0x1000>; + interrupts = <0 85 0>; +}; + +Aliases: +Each G-Scaler node should have a numbered alias in the aliases node, +in the form of gscN, N = 0...3. G-Scaler driver uses these aliases +to retrieve the device IDs using "of_alias_get_id()" call. + +Example: + +aliases { + gsc0 =&gsc_0; + gsc1 =&gsc_1; + gsc2 =&gsc_2; + gsc3 =&gsc_3; +}; diff --git a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt new file mode 100644 index 000000000..56e726ef4 --- /dev/null +++ b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt @@ -0,0 +1,16 @@ +Device-Tree bindings for GPIO IR receiver + +Required properties: + - compatible: should be "gpio-ir-receiver". + - gpios: specifies GPIO used for IR signal reception. + +Optional properties: + - linux,rc-map-name: Linux specific remote control map name. + +Example node: + + ir: ir-receiver { + compatible = "gpio-ir-receiver"; + gpios = <&gpio0 19 1>; + linux,rc-map-name = "rc-rc6-mce"; + }; diff --git a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt new file mode 100644 index 000000000..fb5e76066 --- /dev/null +++ b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt @@ -0,0 +1,25 @@ +Device-Tree bindings for hix5hd2 ir IP + +Required properties: + - compatible: Should contain "hisilicon,hix5hd2-ir". + - reg: Base physical address of the controller and length of memory + mapped region. + - interrupts: interrupt-specifier for the sole interrupt generated by + the device. The interrupt specifier format depends on the interrupt + controller parent. + - clocks: clock phandle and specifier pair. + - hisilicon,power-syscon: phandle of syscon used to control power. + +Optional properties: + - linux,rc-map-name : Remote control map name. + +Example node: + + ir: ir@f8001000 { + compatible = "hisilicon,hix5hd2-ir"; + reg = <0xf8001000 0x1000>; + interrupts = <0 47 4>; + clocks = <&clock HIX5HD2_FIXED_24M>; + hisilicon,power-syscon = <&sysctrl>; + linux,rc-map-name = "rc-tivo"; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7343.txt b/Documentation/devicetree/bindings/media/i2c/adv7343.txt new file mode 100644 index 000000000..5653bc242 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7343.txt @@ -0,0 +1,48 @@ +* Analog Devices adv7343 video encoder + +The ADV7343 are high speed, digital-to-analog video encoders in a 64-lead LQFP +package. Six high speed, 3.3 V, 11-bit video DACs provide support for composite +(CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in standard +definition (SD), enhanced definition (ED), or high definition (HD) video +formats. + +Required Properties : +- compatible: Must be "adi,adv7343" + +Optional Properties : +- adi,power-mode-sleep-mode: on enable the current consumption is reduced to + micro ampere level. All DACs and the internal PLL + circuit are disabled. +- adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows + internal PLL 1 circuit to be powered down and the + oversampling to be switched off. +- ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6, + 0 = OFF and 1 = ON, Default value when this + property is not specified is <0 0 0 0 0 0>. +- ad,adv7343-sd-config-dac-out: array configure SD DAC Output's 1 and 2, 0 = OFF + and 1 = ON, Default value when this property is + not specified is <0 0>. + +Example: + +i2c0@1c22000 { + ... + ... + + adv7343@2a { + compatible = "adi,adv7343"; + reg = <0x2a>; + + port { + adv7343_1: endpoint { + adi,power-mode-sleep-mode; + adi,power-mode-pll-ctrl; + /* Use DAC1..3, DAC6 */ + adi,dac-enable = <1 1 1 0 0 1>; + /* Use SD DAC output 1 */ + adi,sd-dac-enable = <1 0>; + }; + }; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode 100644 index 000000000..c27cede3b --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt @@ -0,0 +1,70 @@ +* Analog Devices ADV7604/11 video decoder with HDMI receiver + +The ADV7604 and ADV7611 are multiformat video decoders with an integrated HDMI +receiver. The ADV7604 has four multiplexed HDMI inputs and one analog input, +and the ADV7611 has one HDMI input and no analog input. + +These device tree bindings support the ADV7611 only at the moment. + +Required Properties: + + - compatible: Must contain one of the following + - "adi,adv7611" for the ADV7611 + + - reg: I2C slave address + + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug + detection pins, one per HDMI input. The active flag indicates the GPIO + level that enables hot-plug detection. + +The device node must contain one 'port' child node per device input and output +port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows. + + Port ADV7611 +------------------------------------------------------------ + HDMI 0 + Digital output 1 + +The digital output port node must contain at least one endpoint. + +Optional Properties: + + - reset-gpios: Reference to the GPIO connected to the device's reset pin. + +Optional Endpoint Properties: + + The following three properties are defined in video-interfaces.txt and are + valid for source endpoints only. + + - hsync-active: Horizontal synchronization polarity. Defaults to active low. + - vsync-active: Vertical synchronization polarity. Defaults to active low. + - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge. + + If none of hsync-active, vsync-active and pclk-sample is specified the + endpoint will use embedded BT.656 synchronization. + + +Example: + + hdmi_receiver@4c { + compatible = "adi,adv7611"; + reg = <0x4c>; + + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; + + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + hdmi_in: endpoint { + remote-endpoint = <&ccdc_in>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt new file mode 100644 index 000000000..ed5a334b1 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt @@ -0,0 +1,28 @@ +Micron 1.3Mp CMOS Digital Image Sensor + +The Micron MT9M111 is a CMOS active pixel digital image sensor with an active +array size of 1280H x 1024V. It is programmable through a simple two-wire serial +interface. + +Required Properties: +- compatible: value should be "micron,mt9m111" + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c_master { + mt9m111@5d { + compatible = "micron,mt9m111"; + reg = <0x5d>; + + remote = <&pxa_camera>; + port { + mt9m111_1: endpoint { + bus-width = <8>; + remote-endpoint = <&pxa_camera>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9p031.txt b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt new file mode 100644 index 000000000..cb60443ff --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt @@ -0,0 +1,40 @@ +* Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor + +The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor with +an active array size of 2592H x 1944V. It is programmable through a simple +two-wire serial interface. + +Required Properties: +- compatible: value should be either one among the following + (a) "aptina,mt9p031" for mt9p031 sensor + (b) "aptina,mt9p031m" for mt9p031m sensor + +- input-clock-frequency: Input clock frequency. + +- pixel-clock-frequency: Pixel clock frequency. + +Optional Properties: +- reset-gpios: Chip reset GPIO + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + mt9p031@5d { + compatible = "aptina,mt9p031"; + reg = <0x5d>; + reset-gpios = <&gpio3 30 0>; + + port { + mt9p031_1: endpoint { + input-clock-frequency = <6000000>; + pixel-clock-frequency = <96000000>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt new file mode 100644 index 000000000..202565313 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt @@ -0,0 +1,39 @@ +* Aptina 1/3-Inch WVGA CMOS Digital Image Sensor + +The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with +an active array size of 752H x 480V. It is programmable through a simple +two-wire serial interface. + +Required Properties: + +- compatible: value should be either one among the following + (a) "aptina,mt9v022" for MT9V022 color sensor + (b) "aptina,mt9v022m" for MT9V022 monochrome sensor + (c) "aptina,mt9v024" for MT9V024 color sensor + (d) "aptina,mt9v024m" for MT9V024 monochrome sensor + (e) "aptina,mt9v032" for MT9V032 color sensor + (f) "aptina,mt9v032m" for MT9V032 monochrome sensor + (g) "aptina,mt9v034" for MT9V034 color sensor + (h) "aptina,mt9v034m" for MT9V034 monochrome sensor + +Optional Properties: + +- link-frequencies: List of allowed link frequencies in Hz. Each frequency is + expressed as a 64-bit big-endian integer. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + mt9v032@5c { + compatible = "aptina,mt9v032"; + reg = <0x5c>; + + port { + mt9v032_out: endpoint { + link-frequencies = /bits/ 64 + <13000000 26600000 27000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt new file mode 100644 index 000000000..855e1faf7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt @@ -0,0 +1,63 @@ +SMIA/SMIA++ sensor + +SMIA (Standard Mobile Imaging Architecture) is an image sensor standard +defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension +of that. These definitions are valid for both types of sensors. + +More detailed documentation can be found in +Documentation/devicetree/bindings/media/video-interfaces.txt . + + +Mandatory properties +-------------------- + +- compatible: "nokia,smia" +- reg: I2C address (0x10, or an alternative address) +- vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor + dependent). +- clocks: External clock to the sensor +- clock-frequency: Frequency of the external clock to the sensor +- link-frequencies: List of allowed data link frequencies. An array of + 64-bit elements. + + +Optional properties +------------------- + +- nokia,nvm-size: The size of the NVM, in bytes. If the size is not given, + the NVM contents will not be read. +- reset-gpios: XSHUTDOWN GPIO + + +Endpoint node mandatory properties +---------------------------------- + +- clock-lanes: <0> +- data-lanes: <1..n> +- remote-endpoint: A phandle to the bus receiver's endpoint node. + + +Example +------- + +&i2c2 { + clock-frequency = <400000>; + + smiapp_1: camera@10 { + compatible = "nokia,smia"; + reg = <0x10>; + reset-gpios = <&gpio3 20 0>; + vana-supply = <&vaux3>; + clocks = <&omap3_isp 0>; + clock-frequency = <9600000>; + nokia,nvm-size = <512>; /* 8 * 64 */ + link-frequencies = /bits/ 64 <199200000 210000000 499200000>; + port { + smiapp_1_1: endpoint { + clock-lanes = <0>; + data-lanes = <1 2>; + remote-endpoint = <&csi2a_ep>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2640.txt b/Documentation/devicetree/bindings/media/i2c/ov2640.txt new file mode 100644 index 000000000..c429b5bdc --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov2640.txt @@ -0,0 +1,46 @@ +* Omnivision OV2640 CMOS sensor + +The Omnivision OV2640 sensor support multiple resolutions output, such as +CIF, SVGA, UXGA. It also can support YUV422/420, RGB565/555 or raw RGB +output format. + +Required Properties: +- compatible: should be "ovti,ov2640" +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". + +Optional Properties: +- resetb-gpios: reference to the GPIO connected to the resetb pin, if any. +- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c1: i2c@f0018000 { + ov2640: camera@0x30 { + compatible = "ovti,ov2640"; + reg = <0x30>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck1 &pinctrl_ov2640_pwdn &pinctrl_ov2640_resetb>; + + resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>; + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>; + + clocks = <&pck1>; + clock-names = "xvclk"; + + assigned-clocks = <&pck1>; + assigned-clock-rates = <25000000>; + + port { + ov2640_0: endpoint { + remote-endpoint = <&isi_0>; + bus-width = <8>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov2659.txt b/Documentation/devicetree/bindings/media/i2c/ov2659.txt new file mode 100644 index 000000000..cabc7d827 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ov2659.txt @@ -0,0 +1,38 @@ +* OV2659 1/5-Inch 2Mp SOC Camera + +The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of +1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports +multiple resolutions output, such as UXGA, SVGA, 720p. It also can support +YUV422, RGB565/555 or raw RGB output formats. + +Required Properties: +- compatible: Must be "ovti,ov2659" +- reg: I2C slave address +- clocks: reference to the xvclk input clock. +- clock-names: should be "xvclk". +- link-frequencies: target pixel clock frequency. + +For further reading on port node refer to +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + ov2659@30 { + compatible = "ovti,ov2659"; + reg = <0x30>; + + clocks = <&clk_ov2659 0>; + clock-names = "xvclk"; + + port { + ov2659_0: endpoint { + remote-endpoint = <&vpfe_ep>; + link-frequencies = /bits/ 64 <70000000>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ths8200.txt b/Documentation/devicetree/bindings/media/i2c/ths8200.txt new file mode 100644 index 000000000..285f6ae7d --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/ths8200.txt @@ -0,0 +1,19 @@ +* Texas Instruments THS8200 video encoder + +The ths8200 device is a digital to analog converter used in DVD players, video +recorders, set-top boxes. + +Required Properties : +- compatible : value must be "ti,ths8200" + +Example: + + i2c0@1c22000 { + ... + ... + ths8200@5c { + compatible = "ti,ths8200"; + reg = <0x5c>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/tvp514x.txt b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt new file mode 100644 index 000000000..46752cc71 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt @@ -0,0 +1,44 @@ +* Texas Instruments TVP514x video decoder + +The TVP5146/TVP5146m2/TVP5147/TVP5147m1 device is high quality, single-chip +digital video decoder that digitizes and decodes all popular baseband analog +video formats into digital video component. The tvp514x decoder supports analog- +to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D +conversion and decoding of NTSC, PAL and SECAM composite and S-video into +component YCbCr. + +Required Properties : +- compatible : value should be either one among the following + (a) "ti,tvp5146" for tvp5146 decoder. + (b) "ti,tvp5146m2" for tvp5146m2 decoder. + (c) "ti,tvp5147" for tvp5147 decoder. + (d) "ti,tvp5147m1" for tvp5147m1 decoder. + +- hsync-active: HSYNC Polarity configuration for endpoint. + +- vsync-active: VSYNC Polarity configuration for endpoint. + +- pclk-sample: Clock polarity of the endpoint. + +For further reading on port node refer to Documentation/devicetree/bindings/ +media/video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + tvp514x@5c { + compatible = "ti,tvp5146"; + reg = <0x5c>; + + port { + tvp514x_1: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/tvp7002.txt b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt new file mode 100644 index 000000000..5f28b5d9a --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt @@ -0,0 +1,53 @@ +* Texas Instruments TV7002 video decoder + +The TVP7002 device supports digitizing of video and graphics signal in RGB and +YPbPr color space. + +Required Properties : +- compatible : Must be "ti,tvp7002" + +Optional Properties: +- hsync-active: HSYNC Polarity configuration for the bus. Default value when + this property is not specified is <0>. + +- vsync-active: VSYNC Polarity configuration for the bus. Default value when + this property is not specified is <0>. + +- pclk-sample: Clock polarity of the bus. Default value when this property is + not specified is <0>. + +- sync-on-green-active: Active state of Sync-on-green signal property of the + endpoint. + 0 = Normal Operation (Active Low, Default) + 1 = Inverted operation + +- field-even-active: Active-high Field ID output polarity control of the bus. + Under normal operation, the field ID output is set to logic 1 for an odd field + (field 1) and set to logic 0 for an even field (field 0). + 0 = Normal Operation (Active Low, Default) + 1 = FID output polarity inverted + +For further reading of port node refer Documentation/devicetree/bindings/media/ +video-interfaces.txt. + +Example: + + i2c0@1c22000 { + ... + ... + tvp7002@5c { + compatible = "ti,tvp7002"; + reg = <0x5c>; + + port { + tvp7002_1: endpoint { + hsync-active = <1>; + vsync-active = <1>; + pclk-sample = <0>; + sync-on-green-active = <1>; + field-even-active = <0>; + }; + }; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/img-ir-rev1.txt b/Documentation/devicetree/bindings/media/img-ir-rev1.txt new file mode 100644 index 000000000..5434ce61b --- /dev/null +++ b/Documentation/devicetree/bindings/media/img-ir-rev1.txt @@ -0,0 +1,34 @@ +* ImgTec Infrared (IR) decoder version 1 + +This binding is for Imagination Technologies' Infrared decoder block, +specifically major revision 1. + +Required properties: +- compatible: Should be "img,ir-rev1" +- reg: Physical base address of the controller and length of + memory mapped region. +- interrupts: The interrupt specifier to the cpu. + +Optional properties: +- clocks: List of clock specifiers as described in standard + clock bindings. + Up to 3 clocks may be specified in the following order: + 1st: Core clock (defaults to 32.768KHz if omitted). + 2nd: System side (fast) clock. + 3rd: Power modulation clock. +- clock-names: List of clock names corresponding to the clocks + specified in the clocks property. + Accepted clock names are: + "core": Core clock. + "sys": System clock. + "mod": Power modulation clock. + +Example: + + ir@02006200 { + compatible = "img,ir-rev1"; + reg = <0x02006200 0x100>; + interrupts = <29 4>; + clocks = <&clk_32khz>; + clock-names = "core"; + }; diff --git a/Documentation/devicetree/bindings/media/meson-ir.txt b/Documentation/devicetree/bindings/media/meson-ir.txt new file mode 100644 index 000000000..407848e85 --- /dev/null +++ b/Documentation/devicetree/bindings/media/meson-ir.txt @@ -0,0 +1,14 @@ +* Amlogic Meson IR remote control receiver + +Required properties: + - compatible : should be "amlogic,meson6-ir" + - reg : physical base address and length of the device registers + - interrupts : a single specifier for the interrupt from the device + +Example: + + ir-receiver@c8100480 { + compatible= "amlogic,meson6-ir"; + reg = <0xc8100480 0x20>; + interrupts = <0 15 1>; + }; diff --git a/Documentation/devicetree/bindings/media/pxa-camera.txt b/Documentation/devicetree/bindings/media/pxa-camera.txt new file mode 100644 index 000000000..11f5b5d51 --- /dev/null +++ b/Documentation/devicetree/bindings/media/pxa-camera.txt @@ -0,0 +1,43 @@ +Marvell PXA camera host interface + +Required properties: + - compatible: Should be "marvell,pxa270-qci" + - reg: register base and size + - interrupts: the interrupt number + - any required generic properties defined in video-interfaces.txt + +Optional properties: + - clocks: input clock (see clock-bindings.txt) + - clock-output-names: should contain the name of the clock driving the + sensor master clock MCLK + - clock-frequency: host interface is driving MCLK, and MCLK rate is this rate + +Example: + + pxa_camera: pxa_camera@50000000 { + compatible = "marvell,pxa270-qci"; + reg = <0x50000000 0x1000>; + interrupts = <33>; + + clocks = <&pxa2xx_clks 24>; + clock-names = "ciclk"; + clock-frequency = <50000000>; + clock-output-names = "qci_mclk"; + + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + /* Parallel bus endpoint */ + qci: endpoint@0 { + reg = <0>; /* Local endpoint # */ + remote-endpoint = <&mt9m111_1>; + bus-width = <8>; /* Used data lines */ + hsync-active = <0>; /* Active low */ + vsync-active = <0>; /* Active low */ + pclk-sample = <1>; /* Rising */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt new file mode 100644 index 000000000..9dafe6b06 --- /dev/null +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -0,0 +1,88 @@ +Renesas RCar Video Input driver (rcar_vin) +------------------------------------------ + +The rcar_vin device provides video input capabilities for the Renesas R-Car +family of devices. The current blocks are always slaves and suppot one input +channel which can be either RGB, YUYV or BT656. + + - compatible: Must be one of the following + - "renesas,vin-r8a7794" for the R8A7794 device + - "renesas,vin-r8a7793" for the R8A7793 device + - "renesas,vin-r8a7791" for the R8A7791 device + - "renesas,vin-r8a7790" for the R8A7790 device + - "renesas,vin-r8a7779" for the R8A7779 device + - "renesas,vin-r8a7778" for the R8A7778 device + - reg: the register base and size for the device registers + - interrupts: the interrupt for the device + - clocks: Reference to the parent clock + +Additionally, an alias named vinX will need to be created to specify +which video input device this is. + +The per-board settings: + - port sub-node describing a single endpoint connected to the vin + as described in video-interfaces.txt[1]. Only the first one will + be considered as each vin interface has one input port. + + These settings are used to work out video input format and widths + into the system. + + +Device node example +------------------- + + aliases { + vin0 = &vin0; + }; + + vin0: vin@0xe6ef0000 { + compatible = "renesas,vin-r8a7790"; + clocks = <&mstp8_clks R8A7790_CLK_VIN0>; + reg = <0 0xe6ef0000 0 0x1000>; + interrupts = <0 188 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + +Board setup example (vin1 composite video input) +------------------------------------------------ + +&i2c2 { + status = "ok"; + pinctrl-0 = <&i2c2_pins>; + pinctrl-names = "default"; + + adv7180@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + remote = <&vin1>; + + port { + adv7180: endpoint { + bus-width = <8>; + remote-endpoint = <&vin1ep0>; + }; + }; + }; +}; + +/* composite video input */ +&vin1 { + pinctrl-0 = <&vin1_pins>; + pinctrl-names = "default"; + + status = "ok"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + vin1ep0: endpoint { + remote-endpoint = <&adv7180>; + bus-width = <8>; + }; + }; +}; + + + +[1] video-interfaces.txt common video media interface diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt new file mode 100644 index 000000000..87fe08abf --- /dev/null +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -0,0 +1,43 @@ +* Renesas VSP1 Video Processing Engine + +The VSP1 is a video processing engine that supports up-/down-scaling, alpha +blending, color space conversion and various other image processing features. +It can be found in the Renesas R-Car second generation SoCs. + +Required properties: + + - compatible: Must contain "renesas,vsp1" + + - reg: Base address and length of the registers block for the VSP1. + - interrupts: VSP1 interrupt specifier. + - clocks: A phandle + clock-specifier pair for the VSP1 functional clock. + + - renesas,#rpf: Number of Read Pixel Formatter (RPF) modules in the VSP1. + - renesas,#uds: Number of Up Down Scaler (UDS) modules in the VSP1. + - renesas,#wpf: Number of Write Pixel Formatter (WPF) modules in the VSP1. + + +Optional properties: + + - renesas,has-lif: Boolean, indicates that the LCD Interface (LIF) module is + available. + - renesas,has-lut: Boolean, indicates that the Look Up Table (LUT) module is + available. + - renesas,has-sru: Boolean, indicates that the Super Resolution Unit (SRU) + module is available. + + +Example: R8A7790 (R-Car H2) VSP1-S node + + vsp1@fe928000 { + compatible = "renesas,vsp1"; + reg = <0 0xfe928000 0 0x8000>; + interrupts = <0 267 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp1_clks R8A7790_CLK_VSP1_S>; + + renesas,has-lut; + renesas,has-sru; + renesas,#rpf = <5>; + renesas,#uds = <3>; + renesas,#wpf = <4>; + }; diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt new file mode 100644 index 000000000..2d5787eac --- /dev/null +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -0,0 +1,51 @@ +* Samsung Multi Format Codec (MFC) + +Multi Format Codec (MFC) is the IP present in Samsung SoCs which +supports high resolution decoding and encoding functionalities. +The MFC device driver is a v4l2 driver which can encode/decode +video raw/elementary streams and has support for all popular +video codecs. + +Required properties: + - compatible : value should be either one among the following + (a) "samsung,mfc-v5" for MFC v5 present in Exynos4 SoCs + (b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs + (c) "samsung,mfc-v7" for MFC v7 present in Exynos5420 SoC + (d) "samsung,mfc-v8" for MFC v8 present in Exynos5800 SoC + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : MFC interrupt number to the CPU. + - clocks : from common clock binding: handle to mfc clock. + - clock-names : from common clock binding: must contain "mfc", + corresponding to entry in the clocks property. + + - samsung,mfc-r : Base address of the first memory bank used by MFC + for DMA contiguous memory allocation and its size. + + - samsung,mfc-l : Base address of the second memory bank used by MFC + for DMA contiguous memory allocation and its size. + +Optional properties: + - power-domains : power-domain property defined with a phandle + to respective power domain. + +Example: +SoC specific DT entry: + +mfc: codec@13400000 { + compatible = "samsung,mfc-v5"; + reg = <0x13400000 0x10000>; + interrupts = <0 94 0>; + power-domains = <&pd_mfc>; + clocks = <&clock 273>; + clock-names = "mfc"; +}; + +Board specific DT entry: + +codec@13400000 { + samsung,mfc-r = <0x43000000 0x800000>; + samsung,mfc-l = <0x51000000 0x800000>; +}; diff --git a/Documentation/devicetree/bindings/media/samsung-fimc.txt b/Documentation/devicetree/bindings/media/samsung-fimc.txt new file mode 100644 index 000000000..922d6f8e7 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-fimc.txt @@ -0,0 +1,211 @@ +Samsung S5P/EXYNOS SoC Camera Subsystem (FIMC) +---------------------------------------------- + +The S5P/Exynos SoC Camera subsystem comprises of multiple sub-devices +represented by separate device tree nodes. Currently this includes: FIMC (in +the S5P SoCs series known as CAMIF), MIPI CSIS, FIMC-LITE and FIMC-IS (ISP). + +The sub-subdevices are defined as child nodes of the common 'camera' node which +also includes common properties of the whole subsystem not really specific to +any single sub-device, like common camera port pins or the CAMCLK clock outputs +for external image sensors attached to an SoC. + +Common 'camera' node +-------------------- + +Required properties: + +- compatible: must be "samsung,fimc", "simple-bus" +- clocks: list of clock specifiers, corresponding to entries in + the clock-names property; +- clock-names : must contain "sclk_cam0", "sclk_cam1", "pxl_async0", + "pxl_async1" entries, matching entries in the clocks property. + +- #clock-cells: from the common clock bindings (../clock/clock-bindings.txt), + must be 1. A clock provider is associated with the 'camera' node and it should + be referenced by external sensors that use clocks provided by the SoC on + CAM_*_CLKOUT pins. The clock specifier cell stores an index of a clock. + The indices are 0, 1 for CAM_A_CLKOUT, CAM_B_CLKOUT clocks respectively. + +- clock-output-names: from the common clock bindings, should contain names of + clocks registered by the camera subsystem corresponding to CAM_A_CLKOUT, + CAM_B_CLKOUT output clocks respectively. + +The pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt must be used +to define a required pinctrl state named "default" and optional pinctrl states: +"idle", "active-a", active-b". These optional states can be used to switch the +camera port pinmux at runtime. The "idle" state should configure both the camera +ports A and B into high impedance state, especially the CAMCLK clock output +should be inactive. For the "active-a" state the camera port A must be activated +and the port B deactivated and for the state "active-b" it should be the other +way around. + +The 'camera' node must include at least one 'fimc' child node. + + +'fimc' device nodes +------------------- + +Required properties: + +- compatible: "samsung,s5pv210-fimc" for S5PV210, "samsung,exynos4210-fimc" + for Exynos4210 and "samsung,exynos4212-fimc" for Exynos4x12 SoCs; +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain FIMC interrupt; +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names; +- clock-names: must contain "fimc", "sclk_fimc" entries. +- samsung,pix-limits: an array of maximum supported image sizes in pixels, for + details refer to Table 2-1 in the S5PV210 SoC User Manual; The meaning of + each cell is as follows: + 0 - scaler input horizontal size, + 1 - input horizontal size for the scaler bypassed, + 2 - REAL_WIDTH without input rotation, + 3 - REAL_HEIGHT with input rotation, +- samsung,sysreg: a phandle to the SYSREG node. + +Each FIMC device should have an alias in the aliases node, in the form of +fimc<n>, where <n> is an integer specifying the IP block instance. + +Optional properties: + +- clock-frequency: maximum FIMC local clock (LCLK) frequency; +- samsung,min-pix-sizes: an array specyfing minimum image size in pixels at + the FIMC input and output DMA, in the first and second cell respectively. + Default value when this property is not present is <16 16>; +- samsung,min-pix-alignment: minimum supported image height alignment (first + cell) and the horizontal image offset (second cell). The values are in pixels + and default to <2 1> when this property is not present; +- samsung,mainscaler-ext: a boolean property indicating whether the FIMC IP + supports extended image size and has CIEXTEN register; +- samsung,rotators: a bitmask specifying whether this IP has the input and + the output rotator. Bits 4 and 0 correspond to input and output rotator + respectively. If a rotator is present its corresponding bit should be set. + Default value when this property is not specified is 0x11. +- samsung,cam-if: a bolean property indicating whether the IP block includes + the camera input interface. +- samsung,isp-wb: this property must be present if the IP block has the ISP + writeback input. +- samsung,lcd-wb: this property must be present if the IP block has the LCD + writeback input. + + +'parallel-ports' node +--------------------- + +This node should contain child 'port' nodes specifying active parallel video +input ports. It includes camera A and camera B inputs. 'reg' property in the +port nodes specifies data input - 0, 1 indicates input A, B respectively. + +Optional properties + +- samsung,camclk-out (deprecated) : specifies clock output for remote sensor, + 0 - CAM_A_CLKOUT, 1 - CAM_B_CLKOUT; + +Image sensor nodes +------------------ + +The sensor device nodes should be added to their control bus controller (e.g. +I2C0) nodes and linked to a port node in the csis or the parallel-ports node, +using the common video interfaces bindings, defined in video-interfaces.txt. + +Example: + + aliases { + fimc0 = &fimc_0; + }; + + /* Parallel bus IF sensor */ + i2c_0: i2c@13860000 { + s5k6aa: sensor@3c { + compatible = "samsung,s5k6aafx"; + reg = <0x3c>; + vddio-supply = <...>; + + clock-frequency = <24000000>; + clocks = <&camera 1>; + clock-names = "mclk"; + + port { + s5k6aa_ep: endpoint { + remote-endpoint = <&fimc0_ep>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <1>; + pclk-sample = <1>; + }; + }; + }; + + /* MIPI CSI-2 bus IF sensor */ + s5c73m3: sensor@0x1a { + compatible = "samsung,s5c73m3"; + reg = <0x1a>; + vddio-supply = <...>; + + clock-frequency = <24000000>; + clocks = <&camera 0>; + clock-names = "mclk"; + + port { + s5c73m3_1: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&csis0_ep>; + }; + }; + }; + }; + + camera { + compatible = "samsung,fimc", "simple-bus"; + clocks = <&clock 132>, <&clock 133>, <&clock 351>, + <&clock 352>; + clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", + "pxl_async1"; + #clock-cells = <1>; + clock-output-names = "cam_a_clkout", "cam_b_clkout"; + pinctrl-names = "default"; + pinctrl-0 = <&cam_port_a_clk_active>; + status = "okay"; + #address-cells = <1>; + #size-cells = <1>; + + /* parallel camera ports */ + parallel-ports { + /* camera A input */ + port@0 { + reg = <0>; + fimc0_ep: endpoint { + remote-endpoint = <&s5k6aa_ep>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <1>; + pclk-sample = <1>; + }; + }; + }; + + fimc_0: fimc@11800000 { + compatible = "samsung,exynos4210-fimc"; + reg = <0x11800000 0x1000>; + interrupts = <0 85 0>; + status = "okay"; + }; + + csis_0: csis@11880000 { + compatible = "samsung,exynos4210-csis"; + reg = <0x11880000 0x1000>; + interrupts = <0 78 0>; + /* camera C input */ + port@3 { + reg = <3>; + csis0_ep: endpoint { + remote-endpoint = <&s5c73m3_ep>; + data-lanes = <1 2 3 4>; + samsung,csis-hs-settle = <12>; + }; + }; + }; + }; + +The MIPI-CSIS device binding is defined in samsung-mipi-csis.txt. diff --git a/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt b/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt new file mode 100644 index 000000000..be45f0b1a --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt @@ -0,0 +1,81 @@ +Samsung S5P/EXYNOS SoC series MIPI CSI-2 receiver (MIPI CSIS) +------------------------------------------------------------- + +Required properties: + +- compatible : "samsung,s5pv210-csis" for S5PV210 (S5PC110), + "samsung,exynos4210-csis" for Exynos4210 (S5PC210), + "samsung,exynos4212-csis" for Exynos4212/Exynos4412, + "samsung,exynos5250-csis" for Exynos5250; +- reg : offset and length of the register set for the device; +- interrupts : should contain MIPI CSIS interrupt; the format of the + interrupt specifier depends on the interrupt controller; +- bus-width : maximum number of data lanes supported (SoC specific); +- vddio-supply : MIPI CSIS I/O and PLL voltage supply (e.g. 1.8V); +- vddcore-supply : MIPI CSIS Core voltage supply (e.g. 1.1V); +- clocks : list of clock specifiers, corresponding to entries in + clock-names property; +- clock-names : must contain "csis", "sclk_csis" entries, matching entries + in the clocks property. + +Optional properties: + +- clock-frequency : The IP's main (system bus) clock frequency in Hz, default + value when this property is not specified is 166 MHz; +- samsung,csis-wclk : CSI-2 wrapper clock selection. If this property is present + external clock from CMU will be used, or the bus clock if + if it's not specified. + +The device node should contain one 'port' child node with one child 'endpoint' +node, according to the bindings defined in Documentation/devicetree/bindings/ +media/video-interfaces.txt. The following are properties specific to those nodes. + +port node +--------- + +- reg : (required) must be 3 for camera C input (CSIS0) or 4 for + camera D input (CSIS1); + +endpoint node +------------- + +- data-lanes : (required) an array specifying active physical MIPI-CSI2 + data input lanes and their mapping to logical lanes; the + array's content is unused, only its length is meaningful; + +- samsung,csis-hs-settle : (optional) differential receiver (HS-RX) settle time; + + +Example: + + reg0: regulator@0 { + }; + + reg1: regulator@1 { + }; + +/* SoC properties */ + + csis_0: csis@11880000 { + compatible = "samsung,exynos4210-csis"; + reg = <0x11880000 0x1000>; + interrupts = <0 78 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + +/* Board properties */ + + csis_0: csis@11880000 { + clock-frequency = <166000000>; + vddio-supply = <®0>; + vddcore-supply = <®1>; + port { + reg = <3>; /* 3 - CSIS0, 4 - CSIS1 */ + csis0_ep: endpoint { + remote-endpoint = <...>; + data-lanes = <1>, <2>; + samsung,csis-hs-settle = <12>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt new file mode 100644 index 000000000..2c85c4538 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt @@ -0,0 +1,97 @@ +Samsung S5C73M3 8Mp camera ISP +------------------------------ + +The S5C73M3 camera ISP supports MIPI CSI-2 and parallel (ITU-R BT.656) video +data busses. The I2C bus is the main control bus and additionally the SPI bus +is used, mostly for transferring the firmware to and from the device. Two +slave device nodes corresponding to these control bus interfaces are required +and should be placed under respective bus controller nodes. + +I2C slave device node +--------------------- + +Required properties: + +- compatible : "samsung,s5c73m3"; +- reg : I2C slave address of the sensor; +- vdd-int-supply : digital power supply (1.2V); +- vdda-supply : analog power supply (1.2V); +- vdd-reg-supply : regulator input power supply (2.8V); +- vddio-host-supply : host I/O power supply (1.8V to 2.8V); +- vddio-cis-supply : CIS I/O power supply (1.2V to 1.8V); +- vdd-af-supply : lens power supply (2.8V); +- xshutdown-gpios : specifier of GPIO connected to the XSHUTDOWN pin; +- standby-gpios : specifier of GPIO connected to the STANDBY pin; +- clocks : should contain list of phandle and clock specifier pairs + according to common clock bindings for the clocks described + in the clock-names property; +- clock-names : should contain "cis_extclk" entry for the CIS_EXTCLK clock; + +Optional properties: + +- clock-frequency : the frequency at which the "cis_extclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used. + +The common video interfaces bindings (see video-interfaces.txt) should be used +to specify link from the S5C73M3 to an external image data receiver. The S5C73M3 +device node should contain one 'port' child node with an 'endpoint' subnode for +this purpose. The data link from a raw image sensor to the S5C73M3 can be +similarly specified, but it is optional since the S5C73M3 ISP and a raw image +sensor are usually inseparable and form a hybrid module. + +Following properties are valid for the endpoint node(s): + +endpoint subnode +---------------- + +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in + video-interfaces.txt. This sensor doesn't support data lane remapping + and physical lane indexes in subsequent elements of the array should + be only consecutive ascending values. + +SPI device node +--------------- + +Required properties: + +- compatible : "samsung,s5c73m3"; + +For more details see description of the SPI busses bindings +(../spi/spi-bus.txt) and bindings of a specific bus controller. + +Example: + +i2c@138A000000 { + ... + s5c73m3@3c { + compatible = "samsung,s5c73m3"; + reg = <0x3c>; + vdd-int-supply = <&buck9_reg>; + vdda-supply = <&ldo17_reg>; + vdd-reg-supply = <&cam_io_reg>; + vddio-host-supply = <&ldo18_reg>; + vddio-cis-supply = <&ldo9_reg>; + vdd-af-supply = <&cam_af_reg>; + clock-frequency = <24000000>; + clocks = <&clk 0>; + clock-names = "cis_extclk"; + reset-gpios = <&gpf1 3 1>; + standby-gpios = <&gpm0 1 1>; + port { + s5c73m3_ep: endpoint { + remote-endpoint = <&csis0_ep>; + data-lanes = <1 2 3 4>; + }; + }; + }; +}; + +spi@1392000 { + ... + s5c73m3_spi: s5c73m3@0 { + compatible = "samsung,s5c73m3"; + reg = <0>; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/media/samsung-s5k5baf.txt b/Documentation/devicetree/bindings/media/samsung-s5k5baf.txt new file mode 100644 index 000000000..1f51e0439 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5k5baf.txt @@ -0,0 +1,58 @@ +Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with embedded SoC ISP +-------------------------------------------------------------------- + +Required properties: + +- compatible : "samsung,s5k5baf"; +- reg : I2C slave address of the sensor; +- vdda-supply : analog power supply 2.8V (2.6V to 3.0V); +- vddreg-supply : regulator input power supply 1.8V (1.7V to 1.9V) + or 2.8V (2.6V to 3.0); +- vddio-supply : I/O power supply 1.8V (1.65V to 1.95V) + or 2.8V (2.5V to 3.1V); +- stbyn-gpios : GPIO connected to STDBYN pin; +- rstn-gpios : GPIO connected to RSTN pin; +- clocks : list of phandle and clock specifier pairs + according to common clock bindings for the + clocks described in clock-names; +- clock-names : should include "mclk" for the sensor's master clock; + +Optional properties: + +- clock-frequency : the frequency at which the "mclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used. + +The device node should contain one 'port' child node with one child 'endpoint' +node, according to the bindings defined in Documentation/devicetree/bindings/ +media/video-interfaces.txt. The following are properties specific to those +nodes. + +endpoint node +------------- + +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in + video-interfaces.txt. If present it should be <1> - the device + supports only one data lane without re-mapping. + +Example: + +s5k5bafx@2d { + compatible = "samsung,s5k5baf"; + reg = <0x2d>; + vdda-supply = <&cam_io_en_reg>; + vddreg-supply = <&vt_core_15v_reg>; + vddio-supply = <&vtcam_reg>; + stbyn-gpios = <&gpl2 0 1>; + rstn-gpios = <&gpl2 1 1>; + clock-names = "mclk"; + clocks = <&clock_cam 0>; + clock-frequency = <24000000>; + + port { + s5k5bafx_ep: endpoint { + remote-endpoint = <&csis1_ep>; + data-lanes = <1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt new file mode 100644 index 000000000..cce01e82f --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt @@ -0,0 +1,33 @@ +Samsung S5K6A3(YX) raw image sensor +--------------------------------- + +S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces +and CCI (I2C compatible) control bus. + +Required properties: + +- compatible : "samsung,s5k6a3"; +- reg : I2C slave address of the sensor; +- svdda-supply : core voltage supply; +- svddio-supply : I/O voltage supply; +- afvdd-supply : AF (actuator) voltage supply; +- gpios : specifier of a GPIO connected to the RESET pin; +- clocks : should contain list of phandle and clock specifier pairs + according to common clock bindings for the clocks described + in the clock-names property; +- clock-names : should contain "extclk" entry for the sensor's EXTCLK clock; + +Optional properties: + +- clock-frequency : the frequency at which the "extclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used. + +The common video interfaces bindings (see video-interfaces.txt) should be +used to specify link to the image data receiver. The S5K6A3(YX) device +node should contain one 'port' child node with an 'endpoint' subnode. + +Following properties are valid for the endpoint node: + +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in + video-interfaces.txt. The sensor supports only one data lane. diff --git a/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt b/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt new file mode 100644 index 000000000..1ce4e46bc --- /dev/null +++ b/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt @@ -0,0 +1,18 @@ +Bindings, specific for the sh_mobile_ceu_camera.c driver: + - compatible: Should be "renesas,sh-mobile-ceu" + - reg: register base and size + - interrupts: the interrupt number + - interrupt-parent: the interrupt controller + - renesas,max-width: maximum image width, supported on this SoC + - renesas,max-height: maximum image height, supported on this SoC + +Example: + +ceu0: ceu@0xfe910000 { + compatible = "renesas,sh-mobile-ceu"; + reg = <0xfe910000 0xa0>; + interrupt-parent = <&intcs>; + interrupts = <0x880>; + renesas,max-width = <8188>; + renesas,max-height = <8188>; +}; diff --git a/Documentation/devicetree/bindings/media/si4713.txt b/Documentation/devicetree/bindings/media/si4713.txt new file mode 100644 index 000000000..5ee5552d3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/si4713.txt @@ -0,0 +1,30 @@ +* Silicon Labs FM Radio transmitter + +The Silicon Labs Si4713 is an FM radio transmitter with receive power scan +supporting 76-108 MHz. It includes an RDS encoder and has both, a stereo-analog +and a digital interface, which supports I2S, left-justified and a custom +DSP-mode format. It is programmable through an I2C interface. + +Required Properties: +- compatible: Should contain "silabs,si4713" +- reg: the I2C address of the device + +Optional Properties: +- interrupts-extended: Interrupt specifier for the chips interrupt +- reset-gpios: GPIO specifier for the chips reset line +- vdd-supply: phandle for Vdd regulator +- vio-supply: phandle for Vio regulator + +Example: + +&i2c2 { + fmtx: si4713@63 { + compatible = "silabs,si4713"; + reg = <0x63>; + + interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */ + reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */ + vio-supply = <&vio>; + vdd-supply = <&vaux1>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/st-rc.txt b/Documentation/devicetree/bindings/media/st-rc.txt new file mode 100644 index 000000000..05c432d08 --- /dev/null +++ b/Documentation/devicetree/bindings/media/st-rc.txt @@ -0,0 +1,29 @@ +Device-Tree bindings for ST IRB IP + +Required properties: + - compatible: Should contain "st,comms-irb". + - reg: Base physical address of the controller and length of memory + mapped region. + - interrupts: interrupt-specifier for the sole interrupt generated by + the device. The interrupt specifier format depends on the interrupt + controller parent. + - rx-mode: can be "infrared" or "uhf". This property specifies the L1 + protocol used for receiving remote control signals. rx-mode should + be present iff the rx pins are wired up. + - tx-mode: should be "infrared". This property specifies the L1 + protocol used for transmitting remote control signals. tx-mode should + be present iff the tx pins are wired up. + +Optional properties: + - pinctrl-names, pinctrl-0: the pincontrol settings to configure muxing + properly for IRB pins. + - clocks : phandle with clock-specifier pair for IRB. + +Example node: + + rc: rc@fe518000 { + compatible = "st,comms-irb"; + reg = <0xfe518000 0x234>; + interrupts = <0 203 0>; + rx-mode = "infrared"; + }; diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt new file mode 100644 index 000000000..1811a067c --- /dev/null +++ b/Documentation/devicetree/bindings/media/sunxi-ir.txt @@ -0,0 +1,25 @@ +Device-Tree bindings for SUNXI IR controller found in sunXi SoC family + +Required properties: +- compatible : "allwinner,sun4i-a10-ir" or "allwinner,sun5i-a13-ir" +- clocks : list of clock specifiers, corresponding to + entries in clock-names property; +- clock-names : should contain "apb" and "ir" entries; +- interrupts : should contain IR IRQ number; +- reg : should contain IO map address for IR. + +Optional properties: +- linux,rc-map-name : Remote control map name. +- resets : phandle + reset specifier pair + +Example: + +ir0: ir@01c21800 { + compatible = "allwinner,sun4i-a10-ir"; + clocks = <&apb0_gates 6>, <&ir0_clk>; + clock-names = "apb", "ir"; + resets = <&apb0_rst 1>; + interrupts = <0 5 1>; + reg = <0x01C21800 0x40>; + linux,rc-map-name = "rc-rc6-mce"; +}; diff --git a/Documentation/devicetree/bindings/media/ti,omap3isp.txt b/Documentation/devicetree/bindings/media/ti,omap3isp.txt new file mode 100644 index 000000000..ac23de855 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti,omap3isp.txt @@ -0,0 +1,71 @@ +OMAP 3 ISP Device Tree bindings +=============================== + +The DT definitions can be found in include/dt-bindings/media/omap3-isp.h. + +Required properties +=================== + +compatible : must contain "ti,omap3-isp" + +reg : the two registers sets (physical address and length) for the + ISP. The first set contains the core ISP registers up to + the end of the SBL block. The second set contains the + CSI PHYs and receivers registers. +interrupts : the ISP interrupt specifier +iommus : phandle and IOMMU specifier for the IOMMU that serves the ISP +syscon : the phandle and register offset to the Complex I/O or CSI-PHY + register +ti,phy-type : 0 -- OMAP3ISP_PHY_TYPE_COMPLEX_IO (e.g. 3430) + 1 -- OMAP3ISP_PHY_TYPE_CSIPHY (e.g. 3630) +#clock-cells : Must be 1 --- the ISP provides two external clocks, + cam_xclka and cam_xclkb, at indices 0 and 1, + respectively. Please find more information on common + clock bindings in ../clock/clock-bindings.txt. + +Port nodes (optional) +--------------------- + +More documentation on these bindings is available in +video-interfaces.txt in the same directory. + +reg : The interface: + 0 - parallel (CCDC) + 1 - CSIPHY1 -- CSI2C / CCP2B on 3630; + CSI1 -- CSIb on 3430 + 2 - CSIPHY2 -- CSI2A / CCP2B on 3630; + CSI2 -- CSIa on 3430 + +Optional properties +=================== + +vdd-csiphy1-supply : voltage supply of the CSI-2 PHY 1 +vdd-csiphy2-supply : voltage supply of the CSI-2 PHY 2 + +Endpoint nodes +-------------- + +lane-polarities : lane polarity (required on CSI-2) + 0 -- not inverted; 1 -- inverted +data-lanes : an array of data lanes from 1 to 3. The length can + be either 1 or 2. (required on CSI-2) +clock-lanes : the clock lane (from 1 to 3). (required on CSI-2) + + +Example +======= + + isp@480bc000 { + compatible = "ti,omap3-isp"; + reg = <0x480bc000 0x12fc + 0x480bd800 0x0600>; + interrupts = <24>; + iommus = <&mmu_isp>; + syscon = <&scm_conf 0x2f0>; + ti,phy-type = <OMAP3ISP_PHY_TYPE_CSIPHY>; + #clock-cells = <1>; + ports { + #address-cells = <1>; + #size-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt b/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt new file mode 100644 index 000000000..3932e7665 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt @@ -0,0 +1,61 @@ +Texas Instruments AM437x CAMERA (VPFE) +-------------------------------------- + +The Video Processing Front End (VPFE) is a key component for image capture +applications. The capture module provides the system interface and the +processing capability to connect RAW image-sensor modules and video decoders +to the AM437x device. + +Required properties: +- compatible: must be "ti,am437x-vpfe" +- reg: physical base address and length of the registers set for the device; +- interrupts: should contain IRQ line for the VPFE; +- ti,am437x-vpfe-interface: can be one of the following, + 0 - Raw Bayer Interface. + 1 - 8 Bit BT656 Interface. + 2 - 10 Bit BT656 Interface. + 3 - YCbCr 8 Bit Interface. + 4 - YCbCr 16 Bit Interface. + +VPFE supports a single port node with parallel bus. It should contain one +'port' child node with child 'endpoint' node. Please refer to the bindings +defined in Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + vpfe: vpfe@f0034000 { + compatible = "ti,am437x-vpfe"; + reg = <0x48328000 0x2000>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&vpfe_pins_default>; + pinctrl-1 = <&vpfe_pins_sleep>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + vpfe0_ep: endpoint { + remote-endpoint = <&ov2659_1>; + ti,am437x-vpfe-interface = <0>; + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; + + i2c1: i2c@4802a000 { + + ov2659@30 { + compatible = "ti,ov2659"; + reg = <0x30>; + + port { + ov2659_1: endpoint { + remote-endpoint = <&vpfe0_ep>; + bus-width = <8>; + mclk-frequency = <12000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt new file mode 100644 index 000000000..9cd2a3691 --- /dev/null +++ b/Documentation/devicetree/bindings/media/video-interfaces.txt @@ -0,0 +1,239 @@ +Common bindings for video receiver and transmitter interfaces + +General concept +--------------- + +Video data pipelines usually consist of external devices, e.g. camera sensors, +controlled over an I2C, SPI or UART bus, and SoC internal IP blocks, including +video DMA engines and video data processors. + +SoC internal blocks are described by DT nodes, placed similarly to other SoC +blocks. External devices are represented as child nodes of their respective +bus controller nodes, e.g. I2C. + +Data interfaces on all video devices are described by their child 'port' nodes. +Configuration of a port depends on other devices participating in the data +transfer and is described by 'endpoint' subnodes. + +device { + ... + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + ... + endpoint@0 { ... }; + endpoint@1 { ... }; + }; + port@1 { ... }; + }; +}; + +If a port can be configured to work with more than one remote device on the same +bus, an 'endpoint' child node must be provided for each of them. If more than +one port is present in a device node or there is more than one endpoint at a +port, or port node needs to be associated with a selected hardware interface, +a common scheme using '#address-cells', '#size-cells' and 'reg' properties is +used. + +All 'port' nodes can be grouped under optional 'ports' node, which allows to +specify #address-cells, #size-cells properties independently for the 'port' +and 'endpoint' nodes and any child device nodes a device might have. + +Two 'endpoint' nodes are linked with each other through their 'remote-endpoint' +phandles. An endpoint subnode of a device contains all properties needed for +configuration of this device for data exchange with other device. In most +cases properties at the peer 'endpoint' nodes will be identical, however they +might need to be different when there is any signal modifications on the bus +between two devices, e.g. there are logic signal inverters on the lines. + +It is allowed for multiple endpoints at a port to be active simultaneously, +where supported by a device. For example, in case where a data interface of +a device is partitioned into multiple data busses, e.g. 16-bit input port +divided into two separate ITU-R BT.656 8-bit busses. In such case bus-width +and data-shift properties can be used to assign physical data lines to each +endpoint node (logical bus). + + +Required properties +------------------- + +If there is more than one 'port' or more than one 'endpoint' node or 'reg' +property is present in port and/or endpoint nodes the following properties +are required in a relevant parent node: + + - #address-cells : number of cells required to define port/endpoint + identifier, should be 1. + - #size-cells : should be zero. + +Optional endpoint properties +---------------------------- + +- remote-endpoint: phandle to an 'endpoint' subnode of a remote device node. +- slave-mode: a boolean property indicating that the link is run in slave mode. + The default when this property is not specified is master mode. In the slave + mode horizontal and vertical synchronization signals are provided to the + slave device (data source) by the master device (data sink). In the master + mode the data source device is also the source of the synchronization signals. +- bus-width: number of data lines actively used, valid for the parallel busses. +- data-shift: on the parallel data busses, if bus-width is used to specify the + number of data lines, data-shift can be used to specify which data lines are + used, e.g. "bus-width=<8>; data-shift=<2>;" means, that lines 9:2 are used. +- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively. +- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. + Note, that if HSYNC and VSYNC polarities are not specified, embedded + synchronization may be required, where supported. +- data-active: similar to HSYNC and VSYNC, specifies data line polarity. +- field-even-active: field signal level during the even field data transmission. +- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock + signal. +- sync-on-green-active: active state of Sync-on-green (SoG) signal, 0/1 for + LOW/HIGH respectively. +- data-lanes: an array of physical data lane indexes. Position of an entry + determines the logical lane number, while the value of an entry indicates + physical lane, e.g. for 2-lane MIPI CSI-2 bus we could have + "data-lanes = <1 2>;", assuming the clock lane is on hardware lane 0. + This property is valid for serial busses only (e.g. MIPI CSI-2). +- clock-lanes: an array of physical clock lane indexes. Position of an entry + determines the logical lane number, while the value of an entry indicates + physical lane, e.g. for a MIPI CSI-2 bus we could have "clock-lanes = <0>;", + which places the clock lane on hardware lane 0. This property is valid for + serial busses only (e.g. MIPI CSI-2). Note that for the MIPI CSI-2 bus this + array contains only one entry. +- clock-noncontinuous: a boolean property to allow MIPI CSI-2 non-continuous + clock mode. +- link-frequencies: Allowed data bus frequencies. For MIPI CSI-2, for + instance, this is the actual frequency of the bus, not bits per clock per + lane value. An array of 64-bit unsigned integers. +- lane-polarities: an array of polarities of the lanes starting from the clock + lane and followed by the data lanes in the same order as in data-lanes. + Valid values are 0 (normal) and 1 (inverted). The length of the array + should be the combined length of data-lanes and clock-lanes properties. + If the lane-polarities property is omitted, the value must be interpreted + as 0 (normal). This property is valid for serial busses only. + + +Example +------- + +The example snippet below describes two data pipelines. ov772x and imx074 are +camera sensors with a parallel and serial (MIPI CSI-2) video bus respectively. +Both sensors are on the I2C control bus corresponding to the i2c0 controller +node. ov772x sensor is linked directly to the ceu0 video host interface. +imx074 is linked to ceu0 through the MIPI CSI-2 receiver (csi2). ceu0 has a +(single) DMA engine writing captured data to memory. ceu0 node has a single +'port' node which may indicate that at any time only one of the following data +pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0. + + ceu0: ceu@0xfe910000 { + compatible = "renesas,sh-mobile-ceu"; + reg = <0xfe910000 0xa0>; + interrupts = <0x880>; + + mclk: master_clock { + compatible = "renesas,ceu-clock"; + #clock-cells = <1>; + clock-frequency = <50000000>; /* Max clock frequency */ + clock-output-names = "mclk"; + }; + + port { + #address-cells = <1>; + #size-cells = <0>; + + /* Parallel bus endpoint */ + ceu0_1: endpoint@1 { + reg = <1>; /* Local endpoint # */ + remote = <&ov772x_1_1>; /* Remote phandle */ + bus-width = <8>; /* Used data lines */ + data-shift = <2>; /* Lines 9:2 are used */ + + /* If hsync-active/vsync-active are missing, + embedded BT.656 sync is used */ + hsync-active = <0>; /* Active low */ + vsync-active = <0>; /* Active low */ + data-active = <1>; /* Active high */ + pclk-sample = <1>; /* Rising */ + }; + + /* MIPI CSI-2 bus endpoint */ + ceu0_0: endpoint@0 { + reg = <0>; + remote = <&csi2_2>; + }; + }; + }; + + i2c0: i2c@0xfff20000 { + ... + ov772x_1: camera@0x21 { + compatible = "ovti,ov772x"; + reg = <0x21>; + vddio-supply = <®ulator1>; + vddcore-supply = <®ulator2>; + + clock-frequency = <20000000>; + clocks = <&mclk 0>; + clock-names = "xclk"; + + port { + /* With 1 endpoint per port no need for addresses. */ + ov772x_1_1: endpoint { + bus-width = <8>; + remote-endpoint = <&ceu0_1>; + hsync-active = <1>; + vsync-active = <0>; /* Who came up with an + inverter here ?... */ + data-active = <1>; + pclk-sample = <1>; + }; + }; + }; + + imx074: camera@0x1a { + compatible = "sony,imx074"; + reg = <0x1a>; + vddio-supply = <®ulator1>; + vddcore-supply = <®ulator2>; + + clock-frequency = <30000000>; /* Shared clock with ov772x_1 */ + clocks = <&mclk 0>; + clock-names = "sysclk"; /* Assuming this is the + name in the datasheet */ + port { + imx074_1: endpoint { + clock-lanes = <0>; + data-lanes = <1 2>; + remote-endpoint = <&csi2_1>; + }; + }; + }; + }; + + csi2: csi2@0xffc90000 { + compatible = "renesas,sh-mobile-csi2"; + reg = <0xffc90000 0x1000>; + interrupts = <0x17a0>; + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + compatible = "renesas,csi2c"; /* One of CSI2I and CSI2C. */ + reg = <1>; /* CSI-2 PHY #1 of 2: PHY_S, + PHY_M has port address 0, + is unused. */ + csi2_1: endpoint { + clock-lanes = <0>; + data-lanes = <2 1>; + remote-endpoint = <&imx074_1>; + }; + }; + port@2 { + reg = <2>; /* port 2: link to the CEU */ + + csi2_2: endpoint { + remote-endpoint = <&ceu0_0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/xilinx/video.txt b/Documentation/devicetree/bindings/media/xilinx/video.txt new file mode 100644 index 000000000..cbd46fa09 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/video.txt @@ -0,0 +1,35 @@ +DT bindings for Xilinx video IP cores +------------------------------------- + +Xilinx video IP cores process video streams by acting as video sinks and/or +sources. They are connected by links through their input and output ports, +creating a video pipeline. + +Each video IP core is represented by an AMBA bus child node in the device +tree using bindings documented in this directory. Connections between the IP +cores are represented as defined in ../video-interfaces.txt. + +The whole pipeline is represented by an AMBA bus child node in the device +tree using bindings documented in ./xlnx,video.txt. + +Common properties +----------------- + +The following properties are common to all Xilinx video IP cores. + +- xlnx,video-format: This property represents a video format transmitted on an + AXI bus between video IP cores, using its VF code as defined in "AXI4-Stream + Video IP and System Design Guide" [UG934]. How the format relates to the IP + core is decribed in the IP core bindings documentation. + +- xlnx,video-width: This property qualifies the video format with the sample + width expressed as a number of bits per pixel component. All components must + use the same width. + +- xlnx,cfa-pattern: When the video format is set to Mono/Sensor, this property + describes the sensor's color filter array pattern. Supported values are + "bggr", "gbrg", "grbg", "rggb" and "mono". If not specified, the pattern + defaults to "mono". + + +[UG934] http://www.xilinx.com/support/documentation/ip_documentation/axi_videoip/v1_0/ug934_axi_videoIP.pdf diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt new file mode 100644 index 000000000..2aed3b4a6 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt @@ -0,0 +1,33 @@ +Xilinx Video Timing Controller (VTC) +------------------------------------ + +The Video Timing Controller is a general purpose video timing generator and +detector. + +Required properties: + + - compatible: Must be "xlnx,v-tc-6.1". + + - reg: Physical base address and length of the registers set for the device. + + - clocks: Must contain a clock specifier for the VTC core and timing + interfaces clock. + +Optional properties: + + - xlnx,detector: The VTC has a timing detector + - xlnx,generator: The VTC has a timing generator + + At least one of the xlnx,detector and xlnx,generator properties must be + specified. + + +Example: + + vtc: vtc@43c40000 { + compatible = "xlnx,v-tc-6.1"; + reg = <0x43c40000 0x10000>; + + clocks = <&clkc 15>; + xlnx,generator; + }; diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt new file mode 100644 index 000000000..9dd86b3db --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt @@ -0,0 +1,71 @@ +Xilinx Video Test Pattern Generator (TPG) +----------------------------------------- + +Required properties: + +- compatible: Must contain at least one of + + "xlnx,v-tpg-5.0" (TPG version 5.0) + "xlnx,v-tpg-6.0" (TPG version 6.0) + + TPG versions backward-compatible with previous versions should list all + compatible versions in the newer to older order. + +- reg: Physical base address and length of the registers set for the device. + +- clocks: Reference to the video core clock. + +- xlnx,video-format, xlnx,video-width: Video format and width, as defined in + video.txt. + +- port: Video port, using the DT bindings defined in ../video-interfaces.txt. + The TPG has a single output port numbered 0. + +Optional properties: + +- xlnx,vtc: A phandle referencing the Video Timing Controller that generates + video timings for the TPG test patterns. + +- timing-gpios: Specifier for a GPIO that controls the timing mux at the TPG + input. The GPIO active level corresponds to the selection of VTC-generated + video timings. + +The xlnx,vtc and timing-gpios properties are mandatory when the TPG is +synthesized with two ports and forbidden when synthesized with one port. + +Example: + + tpg_0: tpg@40050000 { + compatible = "xlnx,v-tpg-6.0", "xlnx,v-tpg-5.0"; + reg = <0x40050000 0x10000>; + clocks = <&clkc 15>; + + xlnx,vtc = <&vtc_3>; + timing-gpios = <&ps7_gpio_0 55 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + xlnx,video-format = <XVIP_VF_YUV_422>; + xlnx,video-width = <8>; + + tpg_in: endpoint { + remote-endpoint = <&adv7611_out>; + }; + }; + port@1 { + reg = <1>; + + xlnx,video-format = <XVIP_VF_YUV_422>; + xlnx,video-width = <8>; + + tpg1_out: endpoint { + remote-endpoint = <&switch_in0>; + }; + }: + }; + }; diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt new file mode 100644 index 000000000..5a0227023 --- /dev/null +++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt @@ -0,0 +1,55 @@ +Xilinx Video IP Pipeline (VIPP) +------------------------------- + +General concept +--------------- + +Xilinx video IP pipeline processes video streams through one or more Xilinx +video IP cores. Each video IP core is represented as documented in video.txt +and IP core specific documentation, xlnx,v-*.txt, in this directory. The DT +node of the VIPP represents as a top level node of the pipeline and defines +mappings between DMAs and the video IP cores. + +Required properties: + +- compatible: Must be "xlnx,video". + +- dmas, dma-names: List of one DMA specifier and identifier string (as defined + in Documentation/devicetree/bindings/dma/dma.txt) per port. Each port + requires a DMA channel with the identifier string set to "port" followed by + the port index. + +- ports: Video port, using the DT bindings defined in ../video-interfaces.txt. + +Required port properties: + +- direction: should be either "input" or "output" depending on the direction + of stream. + +Example: + + video_cap { + compatible = "xlnx,video"; + dmas = <&vdma_1 1>, <&vdma_3 1>; + dma-names = "port0", "port1"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + direction = "input"; + vcap0_in0: endpoint { + remote-endpoint = <&scaler0_out>; + }; + }; + port@1 { + reg = <1>; + direction = "input"; + vcap0_in1: endpoint { + remote-endpoint = <&switch_out1>; + }; + }; + }; + }; |