Linux-libre 4.7.1-gnupck-4.7.1-gnu

5 files changed, 202 insertions, 5 deletions

diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt
index 9b30011ec..a6e2ea411 100644
--- a/Documentation/devicetree/bindings/mfd/arizona.txt
+++ b/Documentation/devicetree/bindings/mfd/arizona.txt
@@ -1,6 +1,6 @@
 Cirrus Logic/Wolfson Microelectronics Arizona class audio SoCs
 
-These devices are audio SoCs with extensive digital capabilites and a range
+These devices are audio SoCs with extensive digital capabilities and a range
 of analogue I/O.
 
 Required properties:
diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
index fd39fa545..d20b1034e 100644
--- a/Documentation/devicetree/bindings/mfd/axp20x.txt
+++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
@@ -6,10 +6,11 @@ axp202 (X-Powers)
 axp209 (X-Powers)
 axp221 (X-Powers)
 axp223 (X-Powers)
+axp809 (X-Powers)
 
 Required properties:
 - compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209",
-	      "x-powers,axp221", "x-powers,axp223"
+	      "x-powers,axp221", "x-powers,axp223", "x-powers,axp809"
 - reg: The I2C slave address or RSB hardware address for the AXP chip
 - interrupt-parent: The parent interrupt controller
 - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
@@ -18,7 +19,9 @@ Required properties:
 
 Optional properties:
 - x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
-		      (range: 750-1875). Default: 1.5MHz
+		      AXP152/20X: range:  750-1875, Default: 1.5 MHz
+		      AXP22X/80X: range: 1800-4050, Default: 3   MHz
+
 - <input>-supply: a phandle to the regulator supply node. May be omitted if
 		  inputs are unregulated, such as using the IPSOUT output
 		  from the PMIC.
@@ -77,6 +80,30 @@ LDO_IO0		: LDO		: ips-supply		: GPIO 0
 LDO_IO1		: LDO		: ips-supply		: GPIO 1
 RTC_LDO		: LDO		: ips-supply		: always on
 
+AXP809 regulators, type, and corresponding input supply names:
+
+Regulator	  Type		  Supply Name		  Notes
+---------	  ----		  -----------		  -----
+DCDC1		: DC-DC buck	: vin1-supply
+DCDC2		: DC-DC buck	: vin2-supply
+DCDC3		: DC-DC	buck	: vin3-supply
+DCDC4		: DC-DC	buck	: vin4-supply
+DCDC5		: DC-DC	buck	: vin5-supply
+DC1SW		: On/Off Switch	:			: DCDC1 secondary output
+DC5LDO		: LDO		:			: input from DCDC5
+ALDO1		: LDO		: aldoin-supply		: shared supply
+ALDO2		: LDO		: aldoin-supply		: shared supply
+ALDO3		: LDO		: aldoin-supply		: shared supply
+DLDO1		: LDO		: dldoin-supply		: shared supply
+DLDO2		: LDO		: dldoin-supply		: shared supply
+ELDO1		: LDO		: eldoin-supply		: shared supply
+ELDO2		: LDO		: eldoin-supply		: shared supply
+ELDO3		: LDO		: eldoin-supply		: shared supply
+LDO_IO0		: LDO		: ips-supply		: GPIO 0
+LDO_IO1		: LDO		: ips-supply		: GPIO 1
+RTC_LDO		: LDO		: ips-supply		: always on
+SW		: On/Off Switch : swin-supply
+
 Example:
 
 axp209: pmic@34 {
diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt
new file mode 100644
index 000000000..05485699d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt
@@ -0,0 +1,27 @@
+Hisilicon Hi655x Power Management Integrated Circuit (PMIC)
+
+The hardware layout for access PMIC Hi655x from AP SoC Hi6220.
+Between PMIC Hi655x and Hi6220, the physical signal channel is SSI.
+We can use memory-mapped I/O to communicate.
+
++----------------+             +-------------+
+|                |             |             |
+|    Hi6220      |   SSI bus   |   Hi655x    |
+|                |-------------|             |
+|                |(REGMAP_MMIO)|             |
++----------------+             +-------------+
+
+Required properties:
+- compatible:           Should be "hisilicon,hi655x-pmic".
+- reg:                  Base address of PMIC on Hi6220 SoC.
+- interrupt-controller: Hi655x has internal IRQs (has own IRQ domain).
+- pmic-gpios:           The GPIO used by PMIC IRQ.
+
+Example:
+	pmic: pmic@f8000000 {
+		compatible = "hisilicon,hi655x-pmic";
+		reg = <0x0 0xf8000000 0x0 0x1000>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	}
diff --git a/Documentation/devicetree/bindings/mfd/max77620.txt b/Documentation/devicetree/bindings/mfd/max77620.txt
new file mode 100644
index 000000000..2ad44f7e4
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77620.txt
@@ -0,0 +1,143 @@
+MAX77620 Power management IC from Maxim Semiconductor.
+
+Required properties:
+-------------------
+- compatible: Must be one of
+		"maxim,max77620"
+		"maxim,max20024".
+- reg: I2C device address.
+
+Optional properties:
+-------------------
+- interrupts:		The interrupt on the parent the controller is
+			connected to.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells:	is <2> and their usage is compliant to the 2 cells
+			variant of <../interrupt-controller/interrupts.txt>
+			IRQ numbers for different interrupt source of MAX77620
+			are defined at dt-bindings/mfd/max77620.h.
+
+Optional subnodes and their properties:
+=======================================
+
+Flexible power sequence configurations:
+--------------------------------------
+The Flexible Power Sequencer (FPS) allows each regulator to power up under
+hardware or software control. Additionally, each regulator can power on
+independently or among a group of other regulators with an adjustable power-up
+and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed
+to be part of a sequence allowing external regulators to be sequenced along
+with internal regulators. 32KHz clock can be programmed to be part of a
+sequence.
+
+The flexible sequencing structure consists of two hardware enable inputs
+(EN0, EN1), and 3 master sequencing timers called FPS0, FPS1 and FPS2.
+Each master sequencing timer is programmable through its configuration
+register to have a hardware enable source (EN1 or EN2) or a software enable
+source (SW). When enabled/disabled, the master sequencing timer generates
+eight sequencing events on different time periods called slots. The time
+period between each event is programmable within the configuration register.
+Each regulator, GPIO1, GPIO2, GPIO3, and 32KHz clock has a flexible power
+sequence slave register which allows its enable source to be specified as
+a flexible power sequencer timer or a software bit. When a FPS source of
+regulators, GPIOs and clocks specifies the enable source to be a flexible
+power sequencer, the power up and power down delays can be specified in
+the regulators, GPIOs and clocks flexible power sequencer configuration
+registers.
+
+When FPS event cleared (set to LOW), regulators, GPIOs and 32KHz
+clock are set into following state at the sequencing event that
+corresponds to its flexible sequencer configuration register.
+	Sleep state: 			In this state, regulators, GPIOs
+					and 32KHz clock get disabled at
+					the sequencing event.
+	Global Low Power Mode (GLPM):	In this state, regulators are set in
+					low power mode at the sequencing event.
+
+The configuration parameters of FPS is provided through sub-node "fps"
+and their child for FPS specific. The child node name for FPS are "fps0",
+"fps1", and "fps2" for FPS0, FPS1 and FPS2 respectively.
+
+The FPS configurations like FPS source, power up and power down slots for
+regulators, GPIOs and 32kHz clocks are provided in their respective
+configuration nodes which is explained in respective sub-system DT
+binding document.
+
+There is need for different FPS configuration parameters based on system
+state like when system state changed from active to suspend or active to
+power off (shutdown).
+
+Optional properties:
+-------------------
+-maxim,fps-event-source:		u32, FPS event source like external
+					hardware input to PMIC i.e. EN0, EN1 or
+					software (SW).
+					The macros are defined on
+						dt-bindings/mfd/max77620.h
+					for different control source.
+					- MAX77620_FPS_EVENT_SRC_EN0
+						for hardware input pin EN0.
+					- MAX77620_FPS_EVENT_SRC_EN1
+						for hardware input pin EN1.
+					- MAX77620_FPS_EVENT_SRC_SW
+						for software control.
+
+-maxim,shutdown-fps-time-period-us:	u32, FPS time period in microseconds
+					when system enters in to shutdown
+					state.
+
+-maxim,suspend-fps-time-period-us:	u32, FPS time period in microseconds
+					when system enters in to suspend state.
+
+-maxim,device-state-on-disabled-event:	u32, describe the PMIC state when FPS
+					event cleared (set to LOW) whether it
+					should go to sleep state or low-power
+					state. Following are valid values:
+					- MAX77620_FPS_INACTIVE_STATE_SLEEP
+						to set the PMIC state to sleep.
+					- MAX77620_FPS_INACTIVE_STATE_LOW_POWER
+						to set the PMIC state to low
+						power.
+					Absence of this property or other value
+					will not change device state when FPS
+					event get cleared.
+
+Here supported time periods by device in microseconds are as follows:
+MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds.
+MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
+
+For DT binding details of different sub modules like GPIO, pincontrol,
+regulator, power, please refer respective device-tree binding document
+under their respective sub-system directories.
+
+Example:
+--------
+#include <dt-bindings/mfd/max77620.h>
+
+max77620@3c {
+	compatible = "maxim,max77620";
+	reg = <0x3c>;
+
+	interrupt-parent = <&intc>;
+	interrupts = <0 86 IRQ_TYPE_NONE>;
+
+	interrupt-controller;
+	#interrupt-cells = <2>;
+
+	fps {
+		fps0 {
+			maxim,shutdown-fps-time-period-us = <1280>;
+			maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
+		};
+
+		fps1 {
+			maxim,shutdown-fps-time-period-us = <1280>;
+			maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+		};
+
+		fps2 {
+			maxim,shutdown-fps-time-period-us = <1280>;
+			maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_SW>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
index 5e97a9593..b98b291a3 100644
--- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
+++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
@@ -178,7 +178,7 @@ see regulator.txt - with additional custom properties described below:
 - qcom,force-mode:
 	Usage: optional (default if no other qcom,force-mode is specified)
 	Value type: <u32>
-	Defintion: indicates that the regulator should be forced to a
+	Definition: indicates that the regulator should be forced to a
 		   particular mode, valid values are:
 		   QCOM_RPM_FORCE_MODE_NONE - do not force any mode
 		   QCOM_RPM_FORCE_MODE_LPM - force into low power mode
@@ -204,7 +204,7 @@ see regulator.txt - with additional custom properties described below:
 - qcom,force-mode:
 	Usage: optional
 	Value type: <u32>
-	Defintion: indicates that the regulator should not be forced to any
+	Definition: indicates that the regulator should not be forced to any
 		   particular mode, valid values are:
 		   QCOM_RPM_FORCE_MODE_NONE - do not force any mode
 		   QCOM_RPM_FORCE_MODE_LPM - force into low power mode