Initial import

1 files changed, 94 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
new file mode 100644
index 000000000..cfb18abe6
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
@@ -0,0 +1,94 @@
+Device tree bindings for Texas instruments Davinci/Keystone NAND controller
+
+This file provides information, what the device node for the davinci/keystone
+NAND interface contains.
+
+Documentation:
+Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
+Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
+
+Required properties:
+
+- compatible:			"ti,davinci-nand"
+				"ti,keystone-nand"
+
+- reg:				Contains 2 offset/length values:
+				- offset and length for the access window.
+				- offset and length for accessing the AEMIF
+				control registers.
+
+- ti,davinci-chipselect:	number of chipselect. Indicates on the
+				davinci_nand driver which chipselect is used
+				for accessing the nand.
+				Can be in the range [0-3].
+
+Recommended properties :
+
+- ti,davinci-mask-ale:		mask for ALE. Needed for executing address
+				phase. These offset will be added to the base
+				address for the chip select space the NAND Flash
+				device is connected to.
+				If not set equal to 0x08.
+
+- ti,davinci-mask-cle:		mask for CLE. Needed for executing command
+				phase. These offset will be added to the base
+				address for the chip select space the NAND Flash
+				device is connected to.
+				If not set equal to 0x10.
+
+- ti,davinci-mask-chipsel:	mask for chipselect address. Needed to mask
+				addresses for given chipselect.
+
+- nand-ecc-mode:		operation mode of the NAND ecc mode. ECC mode
+				valid values for davinci driver:
+				- "none"
+				- "soft"
+				- "hw"
+
+- ti,davinci-ecc-bits:		used ECC bits, currently supported 1 or 4.
+
+- nand-bus-width:		buswidth 8 or 16. If not present 8.
+
+- nand-on-flash-bbt:		use flash based bad block table support. OOB
+				identifier is saved in OOB area. If not present
+				false.
+
+Deprecated properties:
+
+- ti,davinci-ecc-mode:		operation mode of the NAND ecc mode. ECC mode
+				valid values for davinci driver:
+				- "none"
+				- "soft"
+				- "hw"
+
+- ti,davinci-nand-buswidth:	buswidth 8 or 16. If not present 8.
+
+- ti,davinci-nand-use-bbt:	use flash based bad block table support. OOB
+				identifier is saved in OOB area. If not present
+				false.
+
+Nand device bindings may contain additional sub-nodes describing partitions of
+the address space. See partition.txt for more detail. The NAND Flash timing
+values must be programmed in the chip select’s node of AEMIF
+memory-controller (see Documentation/devicetree/bindings/memory-controllers/
+davinci-aemif.txt).
+
+Example(da850 EVM ):
+
+nand_cs3@62000000 {
+	compatible = "ti,davinci-nand";
+	reg = <0x62000000 0x807ff
+	       0x68000000 0x8000>;
+	ti,davinci-chipselect = <1>;
+	ti,davinci-mask-ale = <0>;
+	ti,davinci-mask-cle = <0>;
+	ti,davinci-mask-chipsel = <0>;
+	nand-ecc-mode = "hw";
+	ti,davinci-ecc-bits = <4>;
+	nand-on-flash-bbt;
+
+	partition@180000 {
+		label = "ubifs";
+		reg = <0x180000 0x7e80000>;
+	};
+};