Linux-libre 4.4-gnupck-4.4-gnu

3 files changed, 112 insertions, 29 deletions

diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
index 5235cbc55..32636eb77 100644
--- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
@@ -30,6 +30,12 @@ Optional properties:
                  command is asserted. Zero means one cycle, 255 means 256
                  cycles.
 - bank: default NAND bank to use (0-3 are valid, 0 is the default).
+- nand-ecc-mode      : see nand.txt
+- nand-ecc-strength  : see nand.txt
+- nand-ecc-step-size : see nand.txt
+
+Can support 1-bit HW ECC (default) or if stronger correction is required,
+software-based BCH.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt
index 8e5557da1..1c63e4065 100644
--- a/Documentation/devicetree/bindings/mtd/partition.txt
+++ b/Documentation/devicetree/bindings/mtd/partition.txt
@@ -4,10 +4,19 @@ Partitions can be represented by sub-nodes of an mtd device. This can be used
 on platforms which have strong conventions about which portions of a flash are
 used for what purposes, but which don't use an on-flash partition table such
 as RedBoot.
-NOTE: if the sub-node has a compatible string, then it is not a partition.
 
-#address-cells & #size-cells must both be present in the mtd device. There are
-two valid values for both:
+The partition table should be a subnode of the mtd node and should be named
+'partitions'. This node should have the following property:
+- compatible : (required) must be "fixed-partitions"
+Partitions are then defined in subnodes of the partitions node.
+
+For backwards compatibility partitions as direct subnodes of the mtd device are
+supported. This use is discouraged.
+NOTE: also for backwards compatibility, direct subnodes that have a compatible
+string are not considered partitions, as they may be used for other bindings.
+
+#address-cells & #size-cells must both be present in the partitions subnode of the
+mtd device. There are two valid values for both:
 <1>: for partitions that require a single 32-bit cell to represent their
      size/address (aka the value is below 4 GiB)
 <2>: for partitions that require two 32-bit cells to represent their
@@ -28,44 +37,53 @@ Examples:
 
 
 flash@0 {
-	#address-cells = <1>;
-	#size-cells = <1>;
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
 
-	partition@0 {
-		label = "u-boot";
-		reg = <0x0000000 0x100000>;
-		read-only;
-	};
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0000000 0x100000>;
+			read-only;
+		};
 
-	uimage@100000 {
-		reg = <0x0100000 0x200000>;
+		uimage@100000 {
+			reg = <0x0100000 0x200000>;
+		};
 	};
 };
 
 flash@1 {
-	#address-cells = <1>;
-	#size-cells = <2>;
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <2>;
 
-	/* a 4 GiB partition */
-	partition@0 {
-		label = "filesystem";
-		reg = <0x00000000 0x1 0x00000000>;
+		/* a 4 GiB partition */
+		partition@0 {
+			label = "filesystem";
+			reg = <0x00000000 0x1 0x00000000>;
+		};
 	};
 };
 
 flash@2 {
-	#address-cells = <2>;
-	#size-cells = <2>;
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <2>;
+		#size-cells = <2>;
 
-	/* an 8 GiB partition */
-	partition@0 {
-		label = "filesystem #1";
-		reg = <0x0 0x00000000 0x2 0x00000000>;
-	};
+		/* an 8 GiB partition */
+		partition@0 {
+			label = "filesystem #1";
+			reg = <0x0 0x00000000 0x2 0x00000000>;
+		};
 
-	/* a 4 GiB partition */
-	partition@200000000 {
-		label = "filesystem #2";
-		reg = <0x2 0x00000000 0x1 0x00000000>;
+		/* a 4 GiB partition */
+		partition@200000000 {
+			label = "filesystem #2";
+			reg = <0x2 0x00000000 0x1 0x00000000>;
+		};
 	};
 };
diff --git a/Documentation/devicetree/bindings/mtd/vf610-nfc.txt b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
new file mode 100644
index 000000000..c96eeb65f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
@@ -0,0 +1,59 @@
+Freescale's NAND flash controller (NFC)
+
+This variant of the Freescale NAND flash controller (NFC) can be found on
+Vybrid (vf610), MPC5125, MCF54418 and Kinetis K70.
+
+Required properties:
+- compatible: Should be set to "fsl,vf610-nfc".
+- reg: address range of the NFC.
+- interrupts: interrupt of the NFC.
+- #address-cells: shall be set to 1. Encode the nand CS.
+- #size-cells : shall be set to 0.
+- assigned-clocks: main clock from the SoC, for Vybrid <&clks VF610_CLK_NFC>;
+- assigned-clock-rates: The NAND bus timing is derived from this clock
+    rate and should not exceed maximum timing for any NAND memory chip
+    in a board stuffing. Typical NAND memory timings derived from this
+    clock are found in the SoC hardware reference manual. Furthermore,
+    there might be restrictions on maximum rates when using hardware ECC.
+
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+
+Required children nodes:
+Children nodes represent the available nand chips. Currently the driver can
+only handle one NAND chip.
+
+Required properties:
+- compatible: Should be set to "fsl,vf610-nfc-cs".
+- nand-bus-width: see nand.txt
+- nand-ecc-mode: see nand.txt
+
+Required properties for hardware ECC:
+- nand-ecc-strength: supported strengths are 24 and 32 bit (see nand.txt)
+- nand-ecc-step-size: step size equals page size, currently only 2k pages are
+    supported
+- nand-on-flash-bbt: see nand.txt
+
+Example:
+
+	nfc: nand@400e0000 {
+		compatible = "fsl,vf610-nfc";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x400e0000 0x4000>;
+		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks VF610_CLK_NFC>;
+		clock-names = "nfc";
+		assigned-clocks = <&clks VF610_CLK_NFC>;
+		assigned-clock-rates = <33000000>;
+
+		nand@0 {
+			compatible = "fsl,vf610-nfc-nandcs";
+			reg = <0>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <32>;
+			nand-ecc-step-size = <2048>;
+			nand-on-flash-bbt;
+		};
+	};