Linux-libre 4.7.1-gnupck-4.7.1-gnu

6 files changed, 82 insertions, 11 deletions

diff --git a/Documentation/devicetree/bindings/mtd/arm-versatile.txt b/Documentation/devicetree/bindings/mtd/arm-versatile.txt
index beace4b89..4ec28796a 100644
--- a/Documentation/devicetree/bindings/mtd/arm-versatile.txt
+++ b/Documentation/devicetree/bindings/mtd/arm-versatile.txt
@@ -1,8 +1,26 @@
 Flash device on ARM Versatile board
 
+These flash chips are found in the ARM reference designs like Integrator,
+Versatile, RealView, Versatile Express etc.
+
+They are regular CFI compatible (Intel or AMD extended) flash chips with
+some special write protect/VPP bits that can be controlled by the machine's
+system controller.
+
 Required properties:
-- compatible : must be "arm,versatile-flash";
+- compatible : must be "arm,versatile-flash", "cfi-flash";
+- reg : memory address for the flash chip
 - bank-width : width in bytes of flash interface.
 
+For the rest of the properties, see mtd-physmap.txt.
+
 The device tree may optionally contain sub-nodes describing partitions of the
 address space. See partition.txt for more detail.
+
+Example:
+
+flash@34000000 {
+	compatible = "arm,versatile-flash", "cfi-flash";
+	reg = <0x34000000 0x4000000>;
+	bank-width = <4>;
+};
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
index d53aba98f..3e7ee99d3 100644
--- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -39,7 +39,7 @@ Optional properties:
 
 Nand Flash Controller(NFC) is an optional sub-node
 Required properties:
-- compatible : "atmel,sama5d3-nfc" or "atmel,sama5d4-nfc".
+- compatible : "atmel,sama5d3-nfc".
 - reg : should specify the address and size used for NFC command registers,
         NFC registers and NFC SRAM. NFC SRAM address and size can be absent
         if don't want to use it.
diff --git a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
index c2546ced9..7066597c9 100644
--- a/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
+++ b/Documentation/devicetree/bindings/mtd/brcm,brcmnand.txt
@@ -24,6 +24,7 @@ Required properties:
                          brcm,brcmnand-v5.0
                          brcm,brcmnand-v6.0
                          brcm,brcmnand-v6.1
+                         brcm,brcmnand-v6.2
                          brcm,brcmnand-v7.0
                          brcm,brcmnand-v7.1
                          brcm,brcmnand
@@ -52,7 +53,7 @@ Optional properties:
                               v7.0. Use this property to describe the rare
                               earlier versions of this core that include WP
 
- -- Additonal SoC-specific NAND controller properties --
+ -- Additional SoC-specific NAND controller properties --
 
 The NAND controller is integrated differently on the variety of SoCs on which it
 is found. Part of this integration involves providing status and enable bits
diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
index 0333ec87d..c34aa6f8a 100644
--- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
+++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt
@@ -5,7 +5,8 @@ Required properties:
 		 "fsl,imx7d-qspi", "fsl,imx6ul-qspi",
 		 "fsl,ls1021a-qspi"
 		 or
-		 "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi"
+		 "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi",
+		 "fsl,ls1043a-qspi" followed by "fsl,ls1021a-qspi"
   - reg : the first contains the register location and length,
           the second contains the memory mapping address and length
   - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory"
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
index fb733c4e1..3ee7e2026 100644
--- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
@@ -13,7 +13,11 @@ Documentation/devicetree/bindings/mtd/nand.txt
 
 Required properties:
 
- - reg:		The CS line the peripheral is connected to
+ - compatible:	"ti,omap2-nand"
+ - reg:		range id (CS number), base offset and length of the
+		NAND I/O space
+ - interrupt-parent: must point to gpmc node
+ - interrupts:	Two interrupt specifiers, one for fifoevent, one for termcount.
 
 Optional properties:
 
@@ -44,6 +48,7 @@ Optional properties:
 		locating ECC errors for BCHx algorithms. SoC devices which have
 		ELM hardware engines should specify this device node in .dtsi
 		Using ELM for ECC error correction frees some CPU cycles.
+ - rb-gpios:	GPIO specifier for the ready/busy# pin.
 
 For inline partition table parsing (optional):
 
@@ -55,20 +60,26 @@ Example for an AM33xx board:
 	gpmc: gpmc@50000000 {
 		compatible = "ti,am3352-gpmc";
 		ti,hwmods = "gpmc";
-		reg = <0x50000000 0x1000000>;
+		reg = <0x50000000 0x36c>;
 		interrupts = <100>;
 		gpmc,num-cs = <8>;
 		gpmc,num-waitpins = <2>;
 		#address-cells = <2>;
 		#size-cells = <1>;
-		ranges = <0 0 0x08000000 0x2000>;	/* CS0: NAND */
+		ranges = <0 0 0x08000000 0x1000000>;	/* CS0 space, 16MB */
 		elm_id = <&elm>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
 
 		nand@0,0 {
-			reg = <0 0 0>; /* CS0, offset 0 */
+			compatible = "ti,omap2-nand";
+			reg = <0 0 4>;		/* CS0, offset 0, NAND I/O window 4 */
+			interrupt-parent = <&gpmc>;
+			interrupts = <0 IRQ_TYPE_NONE>, <1 IRQ_TYPE NONE>;
 			nand-bus-width = <16>;
 			ti,nand-ecc-opt = "bch8";
 			ti,nand-xfer-type = "polled";
+			rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
 
 			gpmc,sync-clk-ps = <0>;
 			gpmc,cs-on-ns = <0>;
diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt
index b53f92e25..3733300de 100644
--- a/Documentation/devicetree/bindings/mtd/nand.txt
+++ b/Documentation/devicetree/bindings/mtd/nand.txt
@@ -1,8 +1,31 @@
-* MTD generic binding
+* NAND chip and NAND controller generic binding
+
+NAND controller/NAND chip representation:
+
+The NAND controller should be represented with its own DT node, and all
+NAND chips attached to this controller should be defined as children nodes
+of the NAND controller. This representation should be enforced even for
+simple controllers supporting only one chip.
+
+Mandatory NAND controller properties:
+- #address-cells: depends on your controller. Should at least be 1 to
+		  encode the CS line id.
+- #size-cells: depends on your controller. Put zero unless you need a
+	       mapping between CS lines and dedicated memory regions
+
+Optional NAND controller properties
+- ranges: only needed if you need to define a mapping between CS lines and
+	  memory regions
+
+Optional NAND chip properties:
 
 - nand-ecc-mode : String, operation mode of the NAND ecc mode.
-  Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
-  "soft_bch".
+		  Supported values are: "none", "soft", "hw", "hw_syndrome",
+		  "hw_oob_first".
+		  Deprecated values:
+		  "soft_bch": use "soft" and nand-ecc-algo instead
+- nand-ecc-algo: string, algorithm of NAND ECC.
+		 Supported values are: "hamming", "bch".
 - nand-bus-width : 8 or 16 bus width if not present 8
 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
 
@@ -19,3 +42,20 @@ errors per {size} bytes".
 The interpretation of these parameters is implementation-defined, so not all
 implementations must support all possible combinations. However, implementations
 are encouraged to further specify the value(s) they support.
+
+Example:
+
+	nand-controller {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* controller specific properties */
+
+		nand@0 {
+			reg = <0>;
+			nand-ecc-mode = "soft";
+			nand-ecc-algo = "bch";
+
+			/* controller specific properties */
+		};
+	};