diff options
author | André Fabian Silva Delgado <emulatorman@parabola.nu> | 2016-09-11 04:34:46 -0300 |
---|---|---|
committer | André Fabian Silva Delgado <emulatorman@parabola.nu> | 2016-09-11 04:34:46 -0300 |
commit | 863981e96738983919de841ec669e157e6bdaeb0 (patch) | |
tree | d6d89a12e7eb8017837c057935a2271290907f76 /Documentation/devicetree/bindings/net/wireless | |
parent | 8dec7c70575785729a6a9e6719a955e9c545bcab (diff) |
Linux-libre 4.7.1-gnupck-4.7.1-gnu
Diffstat (limited to 'Documentation/devicetree/bindings/net/wireless')
-rw-r--r-- | Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt | 63 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt | 23 |
2 files changed, 79 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt new file mode 100644 index 000000000..c421aba0a --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt @@ -0,0 +1,63 @@ +Marvell 8897/8997 (sd8897/sd8997) SDIO devices +------ + +This node provides properties for controlling the marvell sdio wireless device. +The node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + + - compatible : should be one of the following: + * "marvell,sd8897" + * "marvell,sd8997" + +Optional properties: + + - marvell,caldata* : A series of properties with marvell,caldata prefix, + represent calibration data downloaded to the device during + initialization. This is an array of unsigned 8-bit values. + the properties should follow below property name and + corresponding array length: + "marvell,caldata-txpwrlimit-2g" (length = 566). + "marvell,caldata-txpwrlimit-5g-sub0" (length = 502). + "marvell,caldata-txpwrlimit-5g-sub1" (length = 688). + "marvell,caldata-txpwrlimit-5g-sub2" (length = 750). + "marvell,caldata-txpwrlimit-5g-sub3" (length = 502). + - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured + to firmware. Firmware will wakeup the host using this pin + during suspend/resume. + - interrupt-parent: phandle of the parent interrupt controller + - interrupts : interrupt pin number to the cpu. driver will request an irq based on + this interrupt number. during system suspend, the irq will be enabled + so that the wifi chip can wakeup host platform under certain condition. + during system resume, the irq will be disabled to make sure + unnecessary interrupt is not received. + +Example: + +Tx power limit calibration data is configured in below example. +The calibration data is an array of unsigned values, the length +can vary between hw versions. +IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured +so that firmware can wakeup host using this device side pin. + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + mwifiex: wifi@1 { + compatible = "marvell,sd8897"; + reg = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + + marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 < + 0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>; + marvell,wakeup-pin = <3>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt index 96aae6b4f..74d7f0af2 100644 --- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -5,12 +5,18 @@ Required properties: * "qcom,ath10k" * "qcom,ipq4019-wifi" -PCI based devices uses compatible string "qcom,ath10k" and takes only -calibration data via "qcom,ath10k-calibration-data". Rest of the properties -are not applicable for PCI based devices. +PCI based devices uses compatible string "qcom,ath10k" and takes calibration +data along with board specific data via "qcom,ath10k-calibration-data". +Rest of the properties are not applicable for PCI based devices. AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi" -and also uses most of the properties defined in this doc. +and also uses most of the properties defined in this doc (except +"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data" +to carry pre calibration data. + +In general, entry "qcom,ath10k-pre-calibration-data" and +"qcom,ath10k-calibration-data" conflict with each other and only one +can be provided per device. Optional properties: - reg: Address and length of the register set for the device. @@ -35,8 +41,11 @@ Optional properties: - qcom,msi_addr: MSI interrupt address. - qcom,msi_base: Base value to add before writing MSI data into MSI address register. -- qcom,ath10k-calibration-data : calibration data as an array, the - length can vary between hw versions +- qcom,ath10k-calibration-data : calibration data + board specific data + as an array, the length can vary between + hw versions. +- qcom,ath10k-pre-calibration-data : pre calibration data as an array, + the length can vary between hw versions. Example (to supply the calibration data alone): @@ -105,5 +114,5 @@ wifi0: wifi@a000000 { "legacy"; qcom,msi_addr = <0x0b006040>; qcom,msi_base = <0x40>; - qcom,ath10k-calibration-data = [ 01 02 03 ... ]; + qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; }; |