diff options
| author | André Fabian Silva Delgado <emulatorman@parabola.nu> | 2015-08-05 17:04:01 -0300 |
|---|---|---|
| committer | André Fabian Silva Delgado <emulatorman@parabola.nu> | 2015-08-05 17:04:01 -0300 |
| commit | 57f0f512b273f60d52568b8c6b77e17f5636edc0 (patch) | |
| tree | 5e910f0e82173f4ef4f51111366a3f1299037a7b /Documentation/devicetree/bindings/net | |
Initial import
Diffstat (limited to 'Documentation/devicetree/bindings/net')
84 files changed, 4253 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt new file mode 100644 index 000000000..10640b17c --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt @@ -0,0 +1,19 @@ +* Allwinner EMAC ethernet controller + +Required properties: +- compatible: should be "allwinner,sun4i-a10-emac" (Deprecated: + "allwinner,sun4i-emac") +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device +- phy: see ethernet.txt file in the same directory. +- clocks: A phandle to the reference clock for this device + +Example: + +emac: ethernet@01c0b000 { + compatible = "allwinner,sun4i-a10-emac"; + reg = <0x01c0b000 0x1000>; + interrupts = <55>; + clocks = <&ahb_gates 17>; + phy = <&phy0>; +}; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt new file mode 100644 index 000000000..4ec564137 --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt @@ -0,0 +1,27 @@ +* Allwinner A10 MDIO Ethernet Controller interface + +Required properties: +- compatible: should be "allwinner,sun4i-a10-mdio" + (Deprecated: "allwinner,sun4i-mdio"). +- reg: address and length of the register set for the device. + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one + +Example at the SoC level: +mdio@01c0b080 { + compatible = "allwinner,sun4i-a10-mdio"; + reg = <0x01c0b080 0x14>; + #address-cells = <1>; + #size-cells = <0>; +}; + +And at the board level: + +mdio@01c0b080 { + phy-supply = <®_emac_3v3>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.txt b/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.txt new file mode 100644 index 000000000..ea4d75238 --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.txt @@ -0,0 +1,27 @@ +* Allwinner GMAC ethernet controller + +This device is a platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +Required properties: + - compatible: Should be "allwinner,sun7i-a20-gmac" + - clocks: Should contain the GMAC main clock, and tx clock + The tx clock type should be "allwinner,sun7i-a20-gmac-clk" + - clock-names: Should contain the clock names "stmmaceth", + and "allwinner_gmac_tx" + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one + +Examples: + + gmac: ethernet@01c50000 { + compatible = "allwinner,sun7i-a20-gmac"; + reg = <0x01c50000 0x10000>, + <0x01c20164 0x4>; + interrupts = <0 85 1>; + interrupt-names = "macirq"; + clocks = <&ahb_gates 49>, <&gmac_tx>; + clock-names = "stmmaceth", "allwinner_gmac_tx"; + phy-mode = "mii"; + }; diff --git a/Documentation/devicetree/bindings/net/altera_tse.txt b/Documentation/devicetree/bindings/net/altera_tse.txt new file mode 100644 index 000000000..a70629799 --- /dev/null +++ b/Documentation/devicetree/bindings/net/altera_tse.txt @@ -0,0 +1,114 @@ +* Altera Triple-Speed Ethernet MAC driver (TSE) + +Required properties: +- compatible: Should be "altr,tse-1.0" for legacy SGDMA based TSE, and should + be "altr,tse-msgdma-1.0" for the preferred MSGDMA based TSE. + ALTR is supported for legacy device trees, but is deprecated. + altr should be used for all new designs. +- reg: Address and length of the register set for the device. It contains + the information of registers in the same order as described by reg-names +- reg-names: Should contain the reg names + "control_port": MAC configuration space region + "tx_csr": xDMA Tx dispatcher control and status space region + "tx_desc": MSGDMA Tx dispatcher descriptor space region + "rx_csr" : xDMA Rx dispatcher control and status space region + "rx_desc": MSGDMA Rx dispatcher descriptor space region + "rx_resp": MSGDMA Rx dispatcher response space region + "s1": SGDMA descriptor memory +- interrupts: Should contain the TSE interrupts and it's mode. +- interrupt-names: Should contain the interrupt names + "rx_irq": xDMA Rx dispatcher interrupt + "tx_irq": xDMA Tx dispatcher interrupt +- rx-fifo-depth: MAC receive FIFO buffer depth in bytes +- tx-fifo-depth: MAC transmit FIFO buffer depth in bytes +- phy-mode: See ethernet.txt in the same directory. +- phy-handle: See ethernet.txt in the same directory. +- phy-addr: See ethernet.txt in the same directory. A configuration should + include phy-handle or phy-addr. +- altr,has-supplementary-unicast: + If present, TSE supports additional unicast addresses. + Otherwise additional unicast addresses are not supported. +- altr,has-hash-multicast-filter: + If present, TSE supports a hash based multicast filter. + Otherwise, hash-based multicast filtering is not supported. + +- mdio device tree subnode: When the TSE has a phy connected to its local + mdio, there must be device tree subnode with the following + required properties: + + - compatible: Must be "altr,tse-mdio". + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For each phy on the mdio bus, there must be a node with the following + fields: + + - reg: phy id used to communicate to phy. + - device_type: Must be "ethernet-phy". + +Optional properties: +- local-mac-address: See ethernet.txt in the same directory. +- max-frame-size: See ethernet.txt in the same directory. + +Example: + + tse_sub_0_eth_tse_0: ethernet@0x1,00000000 { + compatible = "altr,tse-msgdma-1.0"; + reg = <0x00000001 0x00000000 0x00000400>, + <0x00000001 0x00000460 0x00000020>, + <0x00000001 0x00000480 0x00000020>, + <0x00000001 0x000004A0 0x00000008>, + <0x00000001 0x00000400 0x00000020>, + <0x00000001 0x00000420 0x00000020>; + reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 41 4>, <0 40 4>; + interrupt-names = "rx_irq", "tx_irq"; + rx-fifo-depth = <2048>; + tx-fifo-depth = <2048>; + address-bits = <48>; + max-frame-size = <1500>; + local-mac-address = [ 00 00 00 00 00 00 ]; + phy-mode = "gmii"; + altr,has-supplementary-unicast; + altr,has-hash-multicast-filter; + phy-handle = <&phy0>; + mdio { + compatible = "altr,tse-mdio"; + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <0x0>; + device_type = "ethernet-phy"; + }; + + phy1: ethernet-phy@1 { + reg = <0x1>; + device_type = "ethernet-phy"; + }; + + }; + }; + + tse_sub_1_eth_tse_0: ethernet@0x1,00001000 { + compatible = "altr,tse-msgdma-1.0"; + reg = <0x00000001 0x00001000 0x00000400>, + <0x00000001 0x00001460 0x00000020>, + <0x00000001 0x00001480 0x00000020>, + <0x00000001 0x000014A0 0x00000008>, + <0x00000001 0x00001400 0x00000020>, + <0x00000001 0x00001420 0x00000020>; + reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 43 4>, <0 42 4>; + interrupt-names = "rx_irq", "tx_irq"; + rx-fifo-depth = <2048>; + tx-fifo-depth = <2048>; + address-bits = <48>; + max-frame-size = <1500>; + local-mac-address = [ 00 00 00 00 00 00 ]; + phy-mode = "gmii"; + altr,has-supplementary-unicast; + altr,has-hash-multicast-filter; + phy-handle = <&phy1>; + }; diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt new file mode 100644 index 000000000..8db32384a --- /dev/null +++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt @@ -0,0 +1,48 @@ +* AMD 10GbE PHY driver (amd-xgbe-phy) + +Required properties: +- compatible: Should be "amd,xgbe-phy-seattle-v1a" and + "ethernet-phy-ieee802.3-c45" +- reg: Address and length of the register sets for the device + - SerDes Rx/Tx registers + - SerDes integration registers (1/2) + - SerDes integration registers (2/2) +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the amd-xgbe-phy interrupt. + +Optional properties: +- amd,speed-set: Speed capabilities of the device + 0 - 1GbE and 10GbE (default) + 1 - 2.5GbE and 10GbE + +The following optional properties are represented by an array with each +value corresponding to a particular speed. The first array value represents +the setting for the 1GbE speed, the second value for the 2.5GbE speed and +the third value for the 10GbE speed. All three values are required if the +property is used. +- amd,serdes-blwc: Baseline wandering correction enablement + 0 - Off + 1 - On +- amd,serdes-cdr-rate: CDR rate speed selection +- amd,serdes-pq-skew: PQ (data sampling) skew +- amd,serdes-tx-amp: TX amplitude boost +- amd,serdes-dfe-tap-config: DFE taps available to run +- amd,serdes-dfe-tap-enable: DFE taps to enable + +Example: + xgbe_phy@e1240800 { + compatible = "amd,xgbe-phy-seattle-v1a", "ethernet-phy-ieee802.3-c45"; + reg = <0 0xe1240800 0 0x00400>, + <0 0xe1250000 0 0x00060>, + <0 0xe1250080 0 0x00004>; + interrupt-parent = <&gic>; + interrupts = <0 323 4>; + amd,speed-set = <0>; + amd,serdes-blwc = <1>, <1>, <0>; + amd,serdes-cdr-rate = <2>, <2>, <7>; + amd,serdes-pq-skew = <10>, <10>, <30>; + amd,serdes-tx-amp = <15>, <15>, <10>; + amd,serdes-dfe-tap-config = <3>, <3>, <1>; + amd,serdes-dfe-tap-enable = <0>, <0>, <127>; + }; diff --git a/Documentation/devicetree/bindings/net/amd-xgbe.txt b/Documentation/devicetree/bindings/net/amd-xgbe.txt new file mode 100644 index 000000000..26efd526d --- /dev/null +++ b/Documentation/devicetree/bindings/net/amd-xgbe.txt @@ -0,0 +1,47 @@ +* AMD 10GbE driver (amd-xgbe) + +Required properties: +- compatible: Should be "amd,xgbe-seattle-v1a" +- reg: Address and length of the register sets for the device + - MAC registers + - PCS registers +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the amd-xgbe interrupt(s). The first interrupt + listed is required and is the general device interrupt. If the optional + amd,per-channel-interrupt property is specified, then one additional + interrupt for each DMA channel supported by the device should be specified +- clocks: + - DMA clock for the amd-xgbe device (used for calculating the + correct Rx interrupt watchdog timer value on a DMA channel + for coalescing) + - PTP clock for the amd-xgbe device +- clock-names: Should be the names of the clocks + - "dma_clk" for the DMA clock + - "ptp_clk" for the PTP clock +- phy-handle: See ethernet.txt file in the same directory +- phy-mode: See ethernet.txt file in the same directory + +Optional properties: +- mac-address: mac address to be assigned to the device. Can be overridden + by UEFI. +- dma-coherent: Present if dma operations are coherent +- amd,per-channel-interrupt: Indicates that Rx and Tx complete will generate + a unique interrupt for each DMA channel - this requires an additional + interrupt be configured for each DMA channel + +Example: + xgbe@e0700000 { + compatible = "amd,xgbe-seattle-v1a"; + reg = <0 0xe0700000 0 0x80000>, + <0 0xe0780000 0 0x80000>; + interrupt-parent = <&gic>; + interrupts = <0 325 4>, + <0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>; + amd,per-channel-interrupt; + clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>; + clock-names = "dma_clk", "ptp_clk"; + phy-handle = <&phy>; + phy-mode = "xgmii"; + mac-address = [ 02 a1 a2 a3 a4 a5 ]; + }; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt new file mode 100644 index 000000000..f55aa280d --- /dev/null +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -0,0 +1,76 @@ +APM X-Gene SoC Ethernet nodes + +Ethernet nodes are defined to describe on-chip ethernet interfaces in +APM X-Gene SoC. + +Required properties for all the ethernet interfaces: +- compatible: Should state binding information from the following list, + - "apm,xgene-enet": RGMII based 1G interface + - "apm,xgene1-sgenet": SGMII based 1G interface + - "apm,xgene1-xgenet": XFI based 10G interface +- reg: Address and length of the register set for the device. It contains the + information of registers in the same order as described by reg-names +- reg-names: Should contain the register set names + - "enet_csr": Ethernet control and status register address space + - "ring_csr": Descriptor ring control and status register address space + - "ring_cmd": Descriptor ring command register address space +- interrupts: Two interrupt specifiers can be specified. + - First is the Rx interrupt. This irq is mandatory. + - Second is the Tx completion interrupt. + This is supported only on SGMII based 1GbE and 10GbE interfaces. +- port-id: Port number (0 or 1) +- clocks: Reference to the clock entry. +- local-mac-address: MAC address assigned to this device +- phy-connection-type: Interface type between ethernet device and PHY device + +Required properties for ethernet interfaces that have external PHY: +- phy-handle: Reference to a PHY node connected to this device + +- mdio: Device tree subnode with the following required properties: + - compatible: Must be "apm,xgene-mdio". + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For the phy on the mdio bus, there must be a node with the following fields: + - compatible: PHY identifier. Please refer ./phy.txt for the format. + - reg: The ID number for the phy. + +Optional properties: +- status: Should be "ok" or "disabled" for enabled/disabled. Default is "ok". + +Example: + menetclk: menetclk { + compatible = "apm,xgene-device-clock"; + clock-output-names = "menetclk"; + status = "ok"; + }; + + menet: ethernet@17020000 { + compatible = "apm,xgene-enet"; + status = "disabled"; + reg = <0x0 0x17020000 0x0 0xd100>, + <0x0 0X17030000 0x0 0X400>, + <0x0 0X10000000 0x0 0X200>; + reg-names = "enet_csr", "ring_csr", "ring_cmd"; + interrupts = <0x0 0x3c 0x4>; + port-id = <0>; + clocks = <&menetclk 0>; + local-mac-address = [00 01 73 00 00 01]; + phy-connection-type = "rgmii"; + phy-handle = <&menetphy>; + mdio { + compatible = "apm,xgene-mdio"; + #address-cells = <1>; + #size-cells = <0>; + menetphy: menetphy@3 { + compatible = "ethernet-phy-id001c.c915"; + reg = <0x3>; + }; + + }; + }; + +/* Board-specific peripheral configurations */ +&menet { + status = "ok"; +}; diff --git a/Documentation/devicetree/bindings/net/arc_emac.txt b/Documentation/devicetree/bindings/net/arc_emac.txt new file mode 100644 index 000000000..a1d71eb43 --- /dev/null +++ b/Documentation/devicetree/bindings/net/arc_emac.txt @@ -0,0 +1,39 @@ +* Synopsys ARC EMAC 10/100 Ethernet driver (EMAC) + +Required properties: +- compatible: Should be "snps,arc-emac" +- reg: Address and length of the register set for the device +- interrupts: Should contain the EMAC interrupts +- max-speed: see ethernet.txt file in the same directory. +- phy: see ethernet.txt file in the same directory. + +Clock handling: +The clock frequency is needed to calculate and set polling period of EMAC. +It must be provided by one of: +- clock-frequency: CPU frequency. +- clocks: reference to the clock supplying the EMAC. + +Child nodes of the driver are the individual PHY devices connected to the +MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. + +Examples: + + ethernet@c0fc2000 { + compatible = "snps,arc-emac"; + reg = <0xc0fc2000 0x3c>; + interrupts = <6>; + mac-address = [ 00 11 22 33 44 55 ]; + + clock-frequency = <80000000>; + /* or */ + clocks = <&emac_clock>; + + max-speed = <100>; + phy = <&phy0>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt new file mode 100644 index 000000000..30d487597 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt @@ -0,0 +1,78 @@ +* Broadcom Starfighter 2 integrated swich + +Required properties: + +- compatible: should be "brcm,bcm7445-switch-v4.0" +- reg: addresses and length of the register sets for the device, must be 6 + pairs of register addresses and lengths +- interrupts: interrupts for the devices, must be two interrupts +- dsa,mii-bus: phandle to the MDIO bus controller, see dsa/dsa.txt +- dsa,ethernet: phandle to the CPU network interface controller, see dsa/dsa.txt +- #size-cells: must be 0 +- #address-cells: must be 2, see dsa/dsa.txt + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. + +Optional properties: + +- reg-names: litteral names for the device base register addresses, when present + must be: "core", "reg", "intrl2_0", "intrl2_1", "fcb", "acb" + +- interrupt-names: litternal names for the device interrupt lines, when present + must be: "switch_0" and "switch_1" + +- brcm,num-gphy: specify the maximum number of integrated gigabit PHYs in the + switch + +- brcm,num-rgmii-ports: specify the maximum number of RGMII interfaces supported + by the switch + +- brcm,fcb-pause-override: boolean property, if present indicates that the switch + supports Failover Control Block pause override capability + +- brcm,acb-packets-inflight: boolean property, if present indicates that the switch + Admission Control Block supports reporting the number of packets in-flight in a + switch queue + +Example: + +switch_top@f0b00000 { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0 0xf0b00000 0x40804>; + + ethernet_switch@0 { + compatible = "brcm,bcm7445-switch-v4.0"; + #size-cells = <0>; + #address-cells = <2>; + reg = <0x0 0x40000 + 0x40000 0x110 + 0x40340 0x30 + 0x40380 0x30 + 0x40400 0x34 + 0x40600 0x208>; + interrupts = <0 0x18 0 + 0 0x19 0>; + brcm,num-gphy = <1>; + brcm,num-rgmii-ports = <2>; + brcm,fcb-pause-override; + brcm,acb-packets-inflight; + + ... + switch@0 { + reg = <0 0>; + #size-cells = <0>; + #address-cells <1>; + + port@0 { + label = "gphy"; + reg = <0>; + }; + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt new file mode 100644 index 000000000..451fef26b --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt @@ -0,0 +1,121 @@ +* Broadcom BCM7xxx Ethernet Controller (GENET) + +Required properties: +- compatible: should contain one of "brcm,genet-v1", "brcm,genet-v2", + "brcm,genet-v3", "brcm,genet-v4". +- reg: address and length of the register set for the device +- interrupts: must be two cells, the first cell is the general purpose + interrupt line, while the second cell is the interrupt for the ring + RX and TX queues operating in ring mode +- phy-mode: see ethernet.txt file in the same directory +- #address-cells: should be 1 +- #size-cells: should be 1 + +Optional properties: +- clocks: When provided, must be two phandles to the functional clocks nodes + of the GENET block. The first phandle is the main GENET clock used during + normal operation, while the second phandle is the Wake-on-LAN clock. +- clock-names: When provided, names of the functional clock phandles, first + name should be "enet" and second should be "enet-wol". + +- phy-handle: See ethernet.txt file in the same directory; used to describe + configurations where a PHY (internal or external) is used. + +- fixed-link: When the GENET interface is connected to a MoCA hardware block or + when operating in a RGMII to RGMII type of connection, or when the MDIO bus is + voluntarily disabled, this property should be used to describe the "fixed link". + See Documentation/devicetree/bindings/net/fixed-link.txt for information on + the property specifics + +Required child nodes: + +- mdio bus node: this node should always be present regarless of the PHY + configuration of the GENET instance + +MDIO bus node required properties: + +- compatible: should contain one of "brcm,genet-mdio-v1", "brcm,genet-mdio-v2" + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", the version has to match the + parent node compatible property (e.g: brcm,genet-v4 pairs with + brcm,genet-mdio-v4) +- reg: address and length relative to the parent node base register address +- #address-cells: address cell for MDIO bus addressing, should be 1 +- #size-cells: size of the cells for MDIO bus addressing, should be 0 + +Ethernet PHY node properties: + +See Documentation/devicetree/bindings/net/phy.txt for the list of required and +optional properties. + +Internal Gigabit PHY example: + +ethernet@f0b60000 { + phy-mode = "internal"; + phy-handle = <&phy1>; + mac-address = [ 00 10 18 36 23 1a ]; + compatible = "brcm,genet-v4"; + #address-cells = <0x1>; + #size-cells = <0x1>; + reg = <0xf0b60000 0xfc4c>; + interrupts = <0x0 0x14 0x0>, <0x0 0x15 0x0>; + + mdio@e14 { + compatible = "brcm,genet-mdio-v4"; + #address-cells = <0x1>; + #size-cells = <0x0>; + reg = <0xe14 0x8>; + + phy1: ethernet-phy@1 { + max-speed = <1000>; + reg = <0x1>; + compatible = "brcm,28nm-gphy", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +MoCA interface / MAC to MAC example: + +ethernet@f0b80000 { + phy-mode = "moca"; + fixed-link = <1 0 1000 0 0>; + mac-address = [ 00 10 18 36 24 1a ]; + compatible = "brcm,genet-v4"; + #address-cells = <0x1>; + #size-cells = <0x1>; + reg = <0xf0b80000 0xfc4c>; + interrupts = <0x0 0x16 0x0>, <0x0 0x17 0x0>; + + mdio@e14 { + compatible = "brcm,genet-mdio-v4"; + #address-cells = <0x1>; + #size-cells = <0x0>; + reg = <0xe14 0x8>; + }; +}; + + +External MDIO-connected Gigabit PHY/switch: + +ethernet@f0ba0000 { + phy-mode = "rgmii"; + phy-handle = <&phy0>; + mac-address = [ 00 10 18 36 26 1a ]; + compatible = "brcm,genet-v4"; + #address-cells = <0x1>; + #size-cells = <0x1>; + reg = <0xf0ba0000 0xfc4c>; + interrupts = <0x0 0x18 0x0>, <0x0 0x19 0x0>; + + mdio@0e14 { + compatible = "brcm,genet-mdio-v4"; + #address-cells = <0x1>; + #size-cells = <0x0>; + reg = <0xe14 0x8>; + + phy0: ethernet-phy@0 { + max-speed = <1000>; + reg = <0x0>; + compatible = "brcm,bcm53125", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/brcm,systemport.txt b/Documentation/devicetree/bindings/net/brcm,systemport.txt new file mode 100644 index 000000000..877da3414 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,systemport.txt @@ -0,0 +1,30 @@ +* Broadcom BCM7xxx Ethernet Systemport Controller (SYSTEMPORT) + +Required properties: +- compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport" +- reg: address and length of the register set for the device. +- interrupts: interrupts for the device, first cell must be for the rx + interrupts, and the second cell should be for the transmit queues. An + optional third interrupt cell for Wake-on-LAN can be specified +- local-mac-address: Ethernet MAC address (48 bits) of this adapter +- phy-mode: Should be a string describing the PHY interface to the + Ethernet switch/PHY, see Documentation/devicetree/bindings/net/ethernet.txt +- fixed-link: see Documentation/devicetree/bindings/net/fixed-link.txt for + the property specific details + +Optional properties: +- systemport,num-tier2-arb: number of tier 2 arbiters, an integer +- systemport,num-tier1-arb: number of tier 1 arbiters, an integer +- systemport,num-txq: number of HW transmit queues, an integer +- systemport,num-rxq: number of HW receive queues, an integer + +Example: +ethernet@f04a0000 { + compatible = "brcm,systemport-v1.00"; + reg = <0xf04a0000 0x4650>; + local-mac-address = [ 00 11 22 33 44 55 ]; + fixed-link = <0 1 1000 0 0>; + phy-mode = "gmii"; + interrupts = <0x0 0x16 0x0>, + <0x0 0x17 0x0>; +}; diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt new file mode 100644 index 000000000..ab0bb4247 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt @@ -0,0 +1,39 @@ +* Broadcom UniMAC MDIO bus controller + +Required properties: +- compatible: should one from "brcm,genet-mdio-v1", "brcm,genet-mdio-v2", + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4" or "brcm,unimac-mdio" +- reg: address and length of the regsiter set for the device, first one is the + base register, and the second one is optional and for indirect accesses to + larger than 16-bits MDIO transactions +- reg-names: name(s) of the register must be "mdio" and optional "mdio_indir_rw" +- #size-cells: must be 1 +- #address-cells: must be 0 + +Optional properties: +- interrupts: must be one if the interrupt is shared with the Ethernet MAC or + Ethernet switch this MDIO block is integrated from, or must be two, if there + are two separate interrupts, first one must be "mdio done" and second must be + for "mdio error" +- interrupt-names: must be "mdio_done_error" when there is a share interrupt fed + to this hardware block, or must be "mdio_done" for the first interrupt and + "mdio_error" for the second when there are separate interrupts + +Child nodes of this MDIO bus controller node are standard Ethernet PHY device +nodes as described in Documentation/devicetree/bindings/net/phy.txt + +Example: + +mdio@403c0 { + compatible = "brcm,unimac-mdio"; + reg = <0x403c0 0x8 0x40300 0x18>; + reg-names = "mdio", "mdio_indir_rw"; + #size-cells = <1>; + #address-cells = <0>; + + ... + phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt new file mode 100644 index 000000000..7c86d5e28 --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt @@ -0,0 +1,29 @@ +The Broadcom BCM87XX devices are a family of 10G Ethernet PHYs. They +have these bindings in addition to the standard PHY bindings. + +Compatible: Should contain "broadcom,bcm8706" or "broadcom,bcm8727" and + "ethernet-phy-ieee802.3-c45" + +Optional Properties: + +- broadcom,c45-reg-init : one of more sets of 4 cells. The first cell + is the MDIO Manageable Device (MMD) address, the second a register + address within the MMD, the third cell contains a mask to be ANDed + with the existing register value, and the fourth cell is ORed with + he result to yield the new register value. If the third cell has a + value of zero, no read of the existing value is performed. + +Example: + + ethernet-phy@5 { + reg = <5>; + compatible = "broadcom,bcm8706", "ethernet-phy-ieee802.3-c45"; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + /* + * Set PMD Digital Control Register for + * GPIO[1] Tx/Rx + * GPIO[0] R64 Sync Acquired + */ + broadcom,c45-reg-init = <1 0xc808 0xff8f 0x70>; + }; diff --git a/Documentation/devicetree/bindings/net/calxeda-xgmac.txt b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt new file mode 100644 index 000000000..c8ae996bd --- /dev/null +++ b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt @@ -0,0 +1,18 @@ +* Calxeda Highbank 10Gb XGMAC Ethernet + +Required properties: +- compatible : Should be "calxeda,hb-xgmac" +- reg : Address and length of the register set for the device +- interrupts : Should contain 3 xgmac interrupts. The 1st is main interrupt. + The 2nd is pwr mgt interrupt. The 3rd is low power state interrupt. + +Optional properties: +- dma-coherent : Present if dma operations are coherent + +Example: + +ethernet@fff50000 { + compatible = "calxeda,hb-xgmac"; + reg = <0xfff50000 0x1000>; + interrupts = <0 77 4 0 78 4 0 79 4>; +}; diff --git a/Documentation/devicetree/bindings/net/can/atmel-can.txt b/Documentation/devicetree/bindings/net/can/atmel-can.txt new file mode 100644 index 000000000..14e52a0d8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/atmel-can.txt @@ -0,0 +1,14 @@ +* AT91 CAN * + +Required properties: + - compatible: Should be "atmel,at91sam9263-can" or "atmel,at91sam9x5-can" + - reg: Should contain CAN controller registers location and length + - interrupts: Should contain IRQ line for the CAN controller + +Example: + + can0: can@f000c000 { + compatible = "atmel,at91sam9x5-can"; + reg = <0xf000c000 0x300>; + interrupts = <40 4 5> + }; diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt new file mode 100644 index 000000000..5a1d8b0c3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/c_can.txt @@ -0,0 +1,54 @@ +Bosch C_CAN/D_CAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "bosch,c_can" for C_CAN controllers and + "bosch,d_can" for D_CAN controllers. + Can be "ti,dra7-d_can", "ti,am3352-d_can" or + "ti,am4372-d_can". +- reg : physical base address and size of the C_CAN/D_CAN + registers map +- interrupts : property with a value describing the interrupt + number + +Optional properties: +- ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the + instance number +- syscon-raminit : Handle to system control region that contains the + RAMINIT register, register offset to the RAMINIT + register and the CAN instance number (0 offset). + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Example: + +Step1: SoC common .dtsi file + + dcan1: d_can@481d0000 { + compatible = "bosch,d_can"; + reg = <0x481d0000 0x2000>; + interrupts = <55>; + interrupt-parent = <&intc>; + status = "disabled"; + }; + +(or) + + dcan1: d_can@481d0000 { + compatible = "bosch,d_can"; + ti,hwmods = "d_can1"; + reg = <0x481d0000 0x2000>; + interrupts = <55>; + interrupt-parent = <&intc>; + status = "disabled"; + }; + +Step 2: board specific .dts file + + &dcan1 { + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/net/can/cc770.txt b/Documentation/devicetree/bindings/net/can/cc770.txt new file mode 100644 index 000000000..77027bf64 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/cc770.txt @@ -0,0 +1,53 @@ +Memory mapped Bosch CC770 and Intel AN82527 CAN controller + +Note: The CC770 is a CAN controller from Bosch, which is 100% +compatible with the old AN82527 from Intel, but with "bugs" being fixed. + +Required properties: + +- compatible : should be "bosch,cc770" for the CC770 and "intc,82527" + for the AN82527. + +- reg : should specify the chip select, address offset and size required + to map the registers of the controller. The size is usually 0x80. + +- interrupts : property with a value describing the interrupt source + (number and sensitivity) required for the controller. + +Optional properties: + +- bosch,external-clock-frequency : frequency of the external oscillator + clock in Hz. Note that the internal clock frequency used by the + controller is half of that value. If not specified, a default + value of 16000000 (16 MHz) is used. + +- bosch,clock-out-frequency : slock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + +- bosch,slew-rate : slew rate of the CLKOUT signal. If not specified, + a resonable value will be calculated. + +- bosch,disconnect-rx0-input : see data sheet. + +- bosch,disconnect-rx1-input : see data sheet. + +- bosch,disconnect-tx1-output : see data sheet. + +- bosch,polarity-dominant : see data sheet. + +- bosch,divide-memory-clock : see data sheet. + +- bosch,iso-low-speed-mux : see data sheet. + +For further information, please have a look to the CC770 or AN82527. + +Examples: + +can@3,100 { + compatible = "bosch,cc770"; + reg = <3 0x100 0x80>; + interrupts = <2 0>; + interrupt-parent = <&mpic>; + bosch,external-clock-frequency = <16000000>; +}; diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt new file mode 100644 index 000000000..56d6cc336 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -0,0 +1,29 @@ +Flexcan CAN controller on Freescale's ARM and PowerPC system-on-a-chip (SOC). + +Required properties: + +- compatible : Should be "fsl,<processor>-flexcan" + + An implementation should also claim any of the following compatibles + that it is fully backwards compatible with: + + - fsl,p1010-flexcan + +- reg : Offset and length of the register set for this device +- interrupts : Interrupt tuple for this device + +Optional properties: + +- clock-frequency : The oscillator frequency driving the flexcan device + +- xceiver-supply: Regulator that powers the CAN transceiver + +Example: + + can@1c000 { + compatible = "fsl,p1010-flexcan"; + reg = <0x1c000 0x1000>; + interrupts = <48 0x2>; + interrupt-parent = <&mpic>; + clock-frequency = <200000000>; // filled in by bootloader + }; diff --git a/Documentation/devicetree/bindings/net/can/grcan.txt b/Documentation/devicetree/bindings/net/can/grcan.txt new file mode 100644 index 000000000..34ef3498f --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/grcan.txt @@ -0,0 +1,28 @@ +Aeroflex Gaisler GRCAN and GRHCAN CAN controllers. + +The GRCAN and CRHCAN CAN controllers are available in the GRLIB VHDL IP core +library. + +Note: These properties are built from the AMBA plug&play in a Leon SPARC system +(the ordinary environment for GRCAN and GRHCAN). There are no dts files for +sparc. + +Required properties: + +- name : Should be "GAISLER_GRCAN", "01_03d", "GAISLER_GRHCAN" or "01_034" + +- reg : Address and length of the register set for the device + +- freq : Frequency of the external oscillator clock in Hz (the frequency of + the amba bus in the ordinary case) + +- interrupts : Interrupt number for this device + +Optional properties: + +- systemid : If not present or if the value of the least significant 16 bits + of this 32-bit property is smaller than GRCAN_TXBUG_SAFE_GRLIB_VERSION + a bug workaround is activated. + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/net/can/m_can.txt b/Documentation/devicetree/bindings/net/can/m_can.txt new file mode 100644 index 000000000..9e331777c --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/m_can.txt @@ -0,0 +1,67 @@ +Bosch MCAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "bosch,m_can" for M_CAN controllers +- reg : physical base address and size of the M_CAN + registers map and Message RAM +- reg-names : Should be "m_can" and "message_ram" +- interrupts : Should be the interrupt number of M_CAN interrupt + line 0 and line 1, could be same if sharing + the same interrupt. +- interrupt-names : Should contain "int0" and "int1" +- clocks : Clocks used by controller, should be host clock + and CAN clock. +- clock-names : Should contain "hclk" and "cclk" +- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt +- pinctrl-names : Names corresponding to the numbered pinctrl states +- bosch,mram-cfg : Message RAM configuration data. + Multiple M_CAN instances can share the same Message + RAM and each element(e.g Rx FIFO or Tx Buffer and etc) + number in Message RAM is also configurable, + so this property is telling driver how the shared or + private Message RAM are used by this M_CAN controller. + + The format should be as follows: + <offset sidf_elems xidf_elems rxf0_elems rxf1_elems + rxb_elems txe_elems txb_elems> + The 'offset' is an address offset of the Message RAM + where the following elements start from. This is + usually set to 0x0 if you're using a private Message + RAM. The remain cells are used to specify how many + elements are used for each FIFO/Buffer. + + M_CAN includes the following elements according to user manual: + 11-bit Filter 0-128 elements / 0-128 words + 29-bit Filter 0-64 elements / 0-128 words + Rx FIFO 0 0-64 elements / 0-1152 words + Rx FIFO 1 0-64 elements / 0-1152 words + Rx Buffers 0-64 elements / 0-1152 words + Tx Event FIFO 0-32 elements / 0-64 words + Tx Buffers 0-32 elements / 0-576 words + + Please refer to 2.4.1 Message RAM Configuration in + Bosch M_CAN user manual for details. + +Example: +SoC dtsi: +m_can1: can@020e8000 { + compatible = "bosch,m_can"; + reg = <0x020e8000 0x4000>, <0x02298000 0x4000>; + reg-names = "m_can", "message_ram"; + interrupts = <0 114 0x04>, + <0 114 0x04>; + interrupt-names = "int0", "int1"; + clocks = <&clks IMX6SX_CLK_CANFD>, + <&clks IMX6SX_CLK_CANFD>; + clock-names = "hclk", "cclk"; + bosch,mram-cfg = <0x0 0 0 32 0 0 0 1>; + status = "disabled"; +}; + +Board dts: +&m_can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_m_can1>; + status = "enabled"; +}; diff --git a/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt b/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt new file mode 100644 index 000000000..ee3723beb --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt @@ -0,0 +1,25 @@ +* Microchip MCP251X stand-alone CAN controller device tree bindings + +Required properties: + - compatible: Should be one of the following: + - "microchip,mcp2510" for MCP2510. + - "microchip,mcp2515" for MCP2515. + - reg: SPI chip select. + - clocks: The clock feeding the CAN controller. + - interrupt-parent: The parent interrupt controller. + - interrupts: Should contain IRQ line for the CAN controller. + +Optional properties: + - vdd-supply: Regulator that powers the CAN controller. + - xceiver-supply: Regulator that powers the CAN transceiver. + +Example: + can0: can@1 { + compatible = "microchip,mcp2515"; + reg = <1>; + clocks = <&clk24m>; + interrupt-parent = <&gpio4>; + interrupts = <13 0x2>; + vdd-supply = <®5v0>; + xceiver-supply = <®5v0>; + }; diff --git a/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt new file mode 100644 index 000000000..2fa4fcd38 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt @@ -0,0 +1,53 @@ +CAN Device Tree Bindings +------------------------ + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +fsl,mpc5200-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock (XTAL) + "ref" is default in case this property is not + present. + +fsl,mpc5121-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source and divider shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock + "sys" for system clock + If this property is not present, an optimal CAN + clock source and frequency based on the system + clock will be selected. If this is not possible, + the reference clock will be used. + +- fsl,mscan-clock-divider: for the reference and system clock, an additional + clock divider can be specified. By default, a + value of 1 is used. + +Note that the MPC5121 Rev. 1 processor is not supported. + +Examples: + can@1300 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <12 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1300 0x80>; + }; + + can@1380 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <13 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1380 0x80>; + fsl,mscan-clock-source = "ref"; + fsl,mscan-clock-divider = <3>; + }; diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt new file mode 100644 index 000000000..002d8440b --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -0,0 +1,43 @@ +Renesas R-Car CAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible: "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC. + "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC. + "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC. + "renesas,can-r8a7791" if CAN controller is a part of R8A7791 SoC. +- reg: physical base address and size of the R-Car CAN register map. +- interrupts: interrupt specifier for the sole interrupt. +- clocks: phandles and clock specifiers for 3 CAN clock inputs. +- clock-names: 3 clock input name strings: "clkp1", "clkp2", "can_clk". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must be "default". + +Optional properties: +- renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are: + <0x0> (default) : Peripheral clock (clkp1) + <0x1> : Peripheral clock (clkp2) + <0x3> : Externally input clock + +Example +------- + +SoC common .dtsi file: + + can0: can@e6e80000 { + compatible = "renesas,can-r8a7791"; + reg = <0 0xe6e80000 0 0x1000>; + interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_RCAN0>, + <&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + +Board specific .dts file: + +&can0 { + pinctrl-0 = <&can0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt new file mode 100644 index 000000000..b4a6d53fb --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/sja1000.txt @@ -0,0 +1,57 @@ +Memory mapped SJA1000 CAN controller from NXP (formerly Philips) + +Required properties: + +- compatible : should be "nxp,sja1000". + +- reg : should specify the chip select, address offset and size required + to map the registers of the SJA1000. The size is usually 0x80. + +- interrupts: property with a value describing the interrupt source + (number and sensitivity) required for the SJA1000. + +Optional properties: + +- reg-io-width : Specify the size (in bytes) of the IO accesses that + should be performed on the device. Valid value is 1, 2 or 4. + Default to 1 (8 bits). + +- nxp,external-clock-frequency : Frequency of the external oscillator + clock in Hz. Note that the internal clock frequency used by the + SJA1000 is half of that value. If not specified, a default value + of 16000000 (16 MHz) is used. + +- nxp,tx-output-mode : operation mode of the TX output control logic: + <0x0> : bi-phase output mode + <0x1> : normal output mode (default) + <0x2> : test output mode + <0x3> : clock output mode + +- nxp,tx-output-config : TX output pin configuration: + <0x01> : TX0 invert + <0x02> : TX0 pull-down (default) + <0x04> : TX0 pull-up + <0x06> : TX0 push-pull + <0x08> : TX1 invert + <0x10> : TX1 pull-down + <0x20> : TX1 pull-up + <0x30> : TX1 push-pull + +- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + +- nxp,no-comparator-bypass : Allows to disable the CAN input comparator. + +For further information, please have a look to the SJA1000 data sheet. + +Examples: + +can@3,100 { + compatible = "nxp,sja1000"; + reg = <3 0x100 0x80>; + interrupts = <2 0>; + interrupt-parent = <&mpic>; + nxp,external-clock-frequency = <16000000>; +}; + diff --git a/Documentation/devicetree/bindings/net/can/xilinx_can.txt b/Documentation/devicetree/bindings/net/can/xilinx_can.txt new file mode 100644 index 000000000..fe38847d8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/xilinx_can.txt @@ -0,0 +1,44 @@ +Xilinx Axi CAN/Zynq CANPS controller Device Tree Bindings +--------------------------------------------------------- + +Required properties: +- compatible : Should be "xlnx,zynq-can-1.0" for Zynq CAN + controllers and "xlnx,axi-can-1.00.a" for Axi CAN + controllers. +- reg : Physical base address and size of the Axi CAN/Zynq + CANPS registers map. +- interrupts : Property with a value describing the interrupt + number. +- interrupt-parent : Must be core interrupt controller +- clock-names : List of input clock names - "can_clk", "pclk" + (For CANPS), "can_clk" , "s_axi_aclk"(For AXI CAN) + (See clock bindings for details). +- clocks : Clock phandles (see clock bindings for details). +- tx-fifo-depth : Can Tx fifo depth. +- rx-fifo-depth : Can Rx fifo depth. + + +Example: + +For Zynq CANPS Dts file: + zynq_can_0: can@e0008000 { + compatible = "xlnx,zynq-can-1.0"; + clocks = <&clkc 19>, <&clkc 36>; + clock-names = "can_clk", "pclk"; + reg = <0xe0008000 0x1000>; + interrupts = <0 28 4>; + interrupt-parent = <&intc>; + tx-fifo-depth = <0x40>; + rx-fifo-depth = <0x40>; + }; +For Axi CAN Dts file: + axi_can_0: axi-can@40000000 { + compatible = "xlnx,axi-can-1.00.a"; + clocks = <&clkc 0>, <&clkc 1>; + clock-names = "can_clk","s_axi_aclk" ; + reg = <0x40000000 0x10000>; + interrupt-parent = <&intc>; + interrupts = <0 59 1>; + tx-fifo-depth = <0x40>; + rx-fifo-depth = <0x40>; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-mdio.txt b/Documentation/devicetree/bindings/net/cavium-mdio.txt new file mode 100644 index 000000000..04cb7491d --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-mdio.txt @@ -0,0 +1,27 @@ +* System Management Interface (SMI) / MDIO + +Properties: +- compatible: "cavium,octeon-3860-mdio" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the MDIO bus controller register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. MDIO addresses have no size component. + +Typically an MDIO bus might have several children. + +Example: + mdio@1180000001800 { + compatible = "cavium,octeon-3860-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0x00001800 0x0 0x40>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-mix.txt b/Documentation/devicetree/bindings/net/cavium-mix.txt new file mode 100644 index 000000000..8d7c30963 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-mix.txt @@ -0,0 +1,34 @@ +* MIX Ethernet controller. + +Properties: +- compatible: "cavium,octeon-5750-mix" + + Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX + devices. + +- reg: The base addresses of four separate register banks. The first + bank contains the MIX registers. The second bank the corresponding + AGL registers. The third bank are the AGL registers shared by all + MIX devices present. The fourth bank is the AGL_PRT_CTL shared by + all MIX devices present. + +- cell-index: A single cell specifying which portion of the shared + register banks corresponds to this MIX device. + +- interrupts: Two interrupt specifiers. The first is the MIX + interrupt routing and the second the routing for the AGL interrupts. + +- phy-handle: Optional, see ethernet.txt file in the same directory. + +Example: + ethernet@1070000100800 { + compatible = "cavium,octeon-5750-mix"; + reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */ + <0x11800 0xE0000800 0x0 0x300>, /* AGL */ + <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */ + <0x11800 0xE0002008 0x0 0x8>; /* AGL_PRT_CTL */ + cell-index = <1>; + interrupts = <1 18>, < 1 46>; + local-mac-address = [ 00 0f b7 10 63 54 ]; + phy-handle = <&phy1>; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt new file mode 100644 index 000000000..7dbd15881 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-pip.txt @@ -0,0 +1,93 @@ +* PIP Ethernet nexus. + +The PIP Ethernet nexus can control several data packet input/output +devices. The devices have a two level grouping scheme. There may be +several interfaces, and each interface may have several ports. These +ports might be an individual Ethernet PHY. + + +Properties for the PIP nexus: +- compatible: "cavium,octeon-3860-pip" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the PIP's register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. + +Properties for PIP interfaces which is a child the PIP nexus: +- compatible: "cavium,octeon-3860-pip-interface" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The interface number. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. + +Properties for PIP port which is a child the PIP interface: +- compatible: "cavium,octeon-3860-pip-port" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The port number within the interface group. + +- phy-handle: Optional, see ethernet.txt file in the same directory. + +Example: + + pip@11800a0000000 { + compatible = "cavium,octeon-3860-pip"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0xa0000000 0x0 0x2000>; + + interface@0 { + compatible = "cavium,octeon-3860-pip-interface"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; /* interface */ + + ethernet@0 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x0>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 60 ]; + phy-handle = <&phy2>; + }; + ethernet@1 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x1>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 61 ]; + phy-handle = <&phy3>; + }; + ethernet@2 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x2>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 62 ]; + phy-handle = <&phy4>; + }; + ethernet@3 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x3>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 63 ]; + phy-handle = <&phy5>; + }; + }; + + interface@1 { + compatible = "cavium,octeon-3860-pip-interface"; + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; /* interface */ + + ethernet@0 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x0>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 64 ]; + phy-handle = <&phy6>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/cdns-emac.txt b/Documentation/devicetree/bindings/net/cdns-emac.txt new file mode 100644 index 000000000..4451ee973 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cdns-emac.txt @@ -0,0 +1,20 @@ +* Cadence EMAC Ethernet controller + +Required properties: +- compatible: Should be "cdns,[<chip>-]{emac}" + Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. + Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. + Or the generic form: "cdns,emac". +- reg: Address and length of the register set for the device +- interrupts: Should contain macb interrupt +- phy-mode: see ethernet.txt file in the same directory. + +Examples: + + macb0: ethernet@fffc4000 { + compatible = "cdns,at91rm9200-emac"; + reg = <0xfffc4000 0x4000>; + interrupts = <21>; + phy-mode = "rmii"; + local-mac-address = [3a 0e 03 04 05 06]; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt new file mode 100644 index 000000000..764c0c79b --- /dev/null +++ b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt @@ -0,0 +1,30 @@ +TI CPSW Phy mode Selection Device Tree Bindings +----------------------------------------------- + +Required properties: +- compatible : Should be "ti,am3352-cpsw-phy-sel" for am335x platform and + "ti,dra7xx-cpsw-phy-sel" for dra7xx platform + "ti,am43xx-cpsw-phy-sel" for am43xx platform +- reg : physical base address and size of the cpsw + registers map +- reg-names : names of the register map given in "reg" node + +Optional properties: +-rmii-clock-ext : If present, the driver will configure the RMII + interface to external clock usage + +Examples: + + phy_sel: cpsw-phy-sel@44e10650 { + compatible = "ti,am3352-cpsw-phy-sel"; + reg= <0x44e10650 0x4>; + reg-names = "gmii-sel"; + }; + +(or) + phy_sel: cpsw-phy-sel@44e10650 { + compatible = "ti,am3352-cpsw-phy-sel"; + reg= <0x44e10650 0x4>; + reg-names = "gmii-sel"; + rmii-clock-ext; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt new file mode 100644 index 000000000..33fe8462e --- /dev/null +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -0,0 +1,104 @@ +TI SoC Ethernet Switch Controller Device Tree Bindings +------------------------------------------------------ + +Required properties: +- compatible : Should be "ti,cpsw" +- reg : physical base address and size of the cpsw + registers map +- interrupts : property with a value describing the interrupt + number +- interrupt-parent : The parent interrupt controller +- cpdma_channels : Specifies number of channels in CPDMA +- ale_entries : Specifies No of entries ALE can hold +- bd_ram_size : Specifies internal descriptor RAM size +- rx_descs : Specifies number of Rx descriptors +- mac_control : Specifies Default MAC control register content + for the specific platform +- slaves : Specifies number for slaves +- active_slave : Specifies the slave to use for time stamping, + ethtool and SIOCGMIIPHY +- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds +- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds + +Optional properties: +- ti,hwmods : Must be "cpgmac0" +- no_bd_ram : Must be 0 or 1 +- dual_emac : Specifies Switch to act as Dual EMAC +- syscon : Phandle to the system control device node, which is + the control module device of the am33x + +Slave Properties: +Required properties: +- phy_id : Specifies slave phy id +- phy-mode : See ethernet.txt file in the same directory + +Optional properties: +- dual_emac_res_vlan : Specifies VID to be used to segregate the ports +- mac-address : See ethernet.txt file in the same directory + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples: + + mac: ethernet@4A100000 { + compatible = "ti,cpsw"; + reg = <0x4A100000 0x1000>; + interrupts = <55 0x4>; + interrupt-parent = <&intc>; + cpdma_channels = <8>; + ale_entries = <1024>; + bd_ram_size = <0x2000>; + no_bd_ram = <0>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; + syscon = <&cm>; + cpsw_emac0: slave@0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + cpsw_emac1: slave@1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + }; + +(or) + mac: ethernet@4A100000 { + compatible = "ti,cpsw"; + ti,hwmods = "cpgmac0"; + cpdma_channels = <8>; + ale_entries = <1024>; + bd_ram_size = <0x2000>; + no_bd_ram = <0>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; + syscon = <&cm>; + cpsw_emac0: slave@0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + cpsw_emac1: slave@1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + }; diff --git a/Documentation/devicetree/bindings/net/davicom-dm9000.txt b/Documentation/devicetree/bindings/net/davicom-dm9000.txt new file mode 100644 index 000000000..5224bf05f --- /dev/null +++ b/Documentation/devicetree/bindings/net/davicom-dm9000.txt @@ -0,0 +1,28 @@ +Davicom DM9000 Fast Ethernet controller + +Required properties: +- compatible = "davicom,dm9000"; +- reg : physical addresses and sizes of registers, must contain 2 entries: + first entry : address register, + second entry : data register. +- interrupt-parent : interrupt controller to which the device is connected +- interrupts : interrupt specifier specific to interrupt controller + +Optional properties: +- davicom,no-eeprom : Configuration EEPROM is not available +- davicom,ext-phy : Use external PHY +- reset-gpios : phandle of gpio that will be used to reset chip during probe +- vcc-supply : phandle of regulator that will be used to enable power to chip + +Example: + + ethernet@18000000 { + compatible = "davicom,dm9000"; + reg = <0x18000000 0x2 0x18000004 0x2>; + interrupt-parent = <&gpn>; + interrupts = <7 4>; + local-mac-address = [00 00 de ad be ef]; + davicom,no-eeprom; + reset-gpios = <&gpf 12 GPIO_ACTIVE_LOW>; + vcc-supply = <ð0_power>; + }; diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt new file mode 100644 index 000000000..0369e25aa --- /dev/null +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt @@ -0,0 +1,33 @@ +TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings +--------------------------------------------------- + +Required properties: +- compatible : Should be "ti,davinci_mdio" or "ti,keystone_mdio" +- reg : physical base address and size of the davinci mdio + registers map +- bus_freq : Mdio Bus frequency + +Optional properties: +- ti,hwmods : Must be "davinci_mdio" + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples: + + mdio: davinci_mdio@4A101000 { + compatible = "ti,davinci_mdio"; + reg = <0x4A101000 0x1000>; + bus_freq = <1000000>; + }; + +(or) + + mdio: davinci_mdio@4A101000 { + compatible = "ti,davinci_mdio"; + ti,hwmods = "davinci_mdio"; + bus_freq = <1000000>; + }; diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt new file mode 100644 index 000000000..24c5cdaba --- /dev/null +++ b/Documentation/devicetree/bindings/net/davinci_emac.txt @@ -0,0 +1,41 @@ +* Texas Instruments Davinci EMAC + +This file provides information, what the device node +for the davinci_emac interface contains. + +Required properties: +- compatible: "ti,davinci-dm6467-emac", "ti,am3517-emac" or + "ti,dm816-emac" +- reg: Offset and length of the register set for the device +- ti,davinci-ctrl-reg-offset: offset to control register +- ti,davinci-ctrl-mod-reg-offset: offset to control module register +- ti,davinci-ctrl-ram-offset: offset to control module ram +- ti,davinci-ctrl-ram-size: size of control module ram +- interrupts: interrupt mapping for the davinci emac interrupts sources: + 4 sources: <Receive Threshold Interrupt + Receive Interrupt + Transmit Interrupt + Miscellaneous Interrupt> + +Optional properties: +- phy-handle: See ethernet.txt file in the same directory. + If absent, davinci_emac driver defaults to 100/FULL. +- ti,davinci-rmii-en: 1 byte, 1 means use RMII +- ti,davinci-no-bd-ram: boolean, does EMAC have BD RAM? + +Example (enbw_cmc board): + eth0: emac@1e20000 { + compatible = "ti,davinci-dm6467-emac"; + reg = <0x220000 0x4000>; + ti,davinci-ctrl-reg-offset = <0x3000>; + ti,davinci-ctrl-mod-reg-offset = <0x2000>; + ti,davinci-ctrl-ram-offset = <0>; + ti,davinci-ctrl-ram-size = <0x2000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <33 + 34 + 35 + 36 + >; + interrupt-parent = <&intc>; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt new file mode 100644 index 000000000..f0b4cd724 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -0,0 +1,117 @@ +Marvell Distributed Switch Architecture Device Tree Bindings +------------------------------------------------------------ + +Required properties: +- compatible : Should be "marvell,dsa" +- #address-cells : Must be 2, first cell is the address on the MDIO bus + and second cell is the address in the switch tree. + Second cell is used only when cascading/chaining. +- #size-cells : Must be 0 +- dsa,ethernet : Should be a phandle to a valid Ethernet device node +- dsa,mii-bus : Should be a phandle to a valid MDIO bus device node + +Optional properties: +- interrupts : property with a value describing the switch + interrupt number (not supported by the driver) + +A DSA node can contain multiple switch chips which are therefore child nodes of +the parent DSA node. The maximum number of allowed child nodes is 4 +(DSA_MAX_SWITCHES). +Each of these switch child nodes should have the following required properties: + +- reg : Contains two fields. The first one describes the + address on the MII bus. The second is the switch + number that must be unique in cascaded configurations +- #address-cells : Must be 1 +- #size-cells : Must be 0 + +A switch child node has the following optional property: + +- eeprom-length : Set to the length of an EEPROM connected to the + switch. Must be set if the switch can not detect + the presence and/or size of a connected EEPROM, + otherwise optional. + +A switch may have multiple "port" children nodes + +Each port children node must have the following mandatory properties: +- reg : Describes the port address in the switch +- label : Describes the label associated with this port, special + labels are "cpu" to indicate a CPU port and "dsa" to + indicate an uplink/downlink port. + +Note that a port labelled "dsa" will imply checking for the uplink phandle +described below. + +Optionnal property: +- link : Should be a phandle to another switch's DSA port. + This property is only used when switches are being + chained/cascaded together. + +- phy-handle : Phandle to a PHY on an external MDIO bus, not the + switch internal one. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- phy-mode : String representing the connection to the designated + PHY node specified by the 'phy-handle' property. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +Optional subnodes: +- fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + +Example: + + dsa@0 { + compatible = "marvell,dsa"; + #address-cells = <2>; + #size-cells = <0>; + + interrupts = <10>; + dsa,ethernet = <ðernet0>; + dsa,mii-bus = <&mii_bus0>; + + switch@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <16 0>; /* MDIO address 16, switch 0 in tree */ + + port@0 { + reg = <0>; + label = "lan1"; + phy-handle = <&phy0>; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + }; + + switch0uplink: port@6 { + reg = <6>; + label = "dsa"; + link = <&switch1uplink>; + }; + }; + + switch@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <17 1>; /* MDIO address 17, switch 1 in tree */ + + switch1uplink: port@0 { + reg = <0>; + label = "dsa"; + link = <&switch0uplink>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/emac_rockchip.txt b/Documentation/devicetree/bindings/net/emac_rockchip.txt new file mode 100644 index 000000000..8dc1c79fe --- /dev/null +++ b/Documentation/devicetree/bindings/net/emac_rockchip.txt @@ -0,0 +1,50 @@ +* ARC EMAC 10/100 Ethernet platform driver for Rockchip Rk3066/RK3188 SoCs + +Required properties: +- compatible: Should be "rockchip,rk3066-emac" or "rockchip,rk3188-emac" + according to the target SoC. +- reg: Address and length of the register set for the device +- interrupts: Should contain the EMAC interrupts +- rockchip,grf: phandle to the syscon grf used to control speed and mode + for emac. +- phy: see ethernet.txt file in the same directory. +- phy-mode: see ethernet.txt file in the same directory. + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one + +Clock handling: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Shall be "hclk" for the host clock needed to calculate and set + polling period of EMAC and "macref" for the reference clock needed to transfer + data to and from the phy. + +Child nodes of the driver are the individual PHY devices connected to the +MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. + +Examples: + +ethernet@10204000 { + compatible = "rockchip,rk3188-emac"; + reg = <0xc0fc2000 0x3c>; + interrupts = <6>; + mac-address = [ 00 11 22 33 44 55 ]; + + clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>; + clock-names = "hclk", "macref"; + + pinctrl-names = "default"; + pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>; + + rockchip,grf = <&grf>; + + phy = <&phy0>; + phy-mode = "rmii"; + phy-supply = <&vcc_rmii>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt new file mode 100644 index 000000000..41b3f3f86 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -0,0 +1,31 @@ +The following properties are common to the Ethernet controllers: + +- local-mac-address: array of 6 bytes, specifies the MAC address that was + assigned to the network device; +- mac-address: array of 6 bytes, specifies the MAC address that was last used by + the boot program; should be used in cases where the MAC address assigned to + the device by the boot program is different from the "local-mac-address" + property; +- max-speed: number, specifies maximum speed in Mbit/s supported by the device; +- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than + the maximum frame size (there's contradiction in ePAPR). +- phy-mode: string, operation mode of the PHY interface; supported values are + "mii", "gmii", "sgmii", "qsgmii", "tbi", "rev-mii", "rmii", "rgmii", "rgmii-id", + "rgmii-rxid", "rgmii-txid", "rtbi", "smii", "xgmii"; this is now a de-facto + standard property; +- phy-connection-type: the same as "phy-mode" property but described in ePAPR; +- phy-handle: phandle, specifies a reference to a node representing a PHY + device; this property is described in ePAPR and so preferred; +- phy: the same as "phy-handle" property, not recommended for new bindings. +- phy-device: the same as "phy-handle" property, not recommended for new + bindings. +- rx-fifo-depth: the size of the controller's receive fifo in bytes. This + is used for components that can have configurable receive fifo sizes, + and is useful for determining certain configuration settings such as + flow control thresholds. +- tx-fifo-depth: the size of the controller's transmit fifo in bytes. This + is used for components that can have configurable fifo sizes. + +Child nodes of the Ethernet controller are typically the individual PHY devices +connected via the MDIO bus (sometimes the MDIO bus controller is separate). +They are described in the phy.txt file in this same directory. diff --git a/Documentation/devicetree/bindings/net/fixed-link.txt b/Documentation/devicetree/bindings/net/fixed-link.txt new file mode 100644 index 000000000..82bf7e0f4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/fixed-link.txt @@ -0,0 +1,42 @@ +Fixed link Device Tree binding +------------------------------ + +Some Ethernet MACs have a "fixed link", and are not connected to a +normal MDIO-managed PHY device. For those situations, a Device Tree +binding allows to describe a "fixed link". + +Such a fixed link situation is described by creating a 'fixed-link' +sub-node of the Ethernet MAC device node, with the following +properties: + +* 'speed' (integer, mandatory), to indicate the link speed. Accepted + values are 10, 100 and 1000 +* 'full-duplex' (boolean, optional), to indicate that full duplex is + used. When absent, half duplex is assumed. +* 'pause' (boolean, optional), to indicate that pause should be + enabled. +* 'asym-pause' (boolean, optional), to indicate that asym_pause should + be enabled. + +Old, deprecated 'fixed-link' binding: + +* A 'fixed-link' property in the Ethernet MAC node, with 5 cells, of the + form <a b c d e> with the following accepted values: + - a: emulated PHY ID, choose any but but unique to the all specified + fixed-links, from 0 to 31 + - b: duplex configuration: 0 for half duplex, 1 for full duplex + - c: link speed in Mbits/sec, accepted values are: 10, 100 and 1000 + - d: pause configuration: 0 for no pause, 1 for pause + - e: asymmetric pause configuration: 0 for no asymmetric pause, 1 for + asymmetric pause + +Example: + +ethernet@0 { + ... + fixed-link { + speed = <1000>; + full-duplex; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt new file mode 100644 index 000000000..a9eb611be --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -0,0 +1,62 @@ +* Freescale Fast Ethernet Controller (FEC) + +Required properties: +- compatible : Should be "fsl,<soc>-fec" +- reg : Address and length of the register set for the device +- interrupts : Should contain fec interrupt +- phy-mode : See ethernet.txt file in the same directory + +Optional properties: +- phy-reset-gpios : Should specify the gpio for phy reset +- phy-reset-duration : Reset duration in milliseconds. Should present + only if property "phy-reset-gpios" is available. Missing the property + will have the duration be 1 millisecond. Numbers greater than 1000 are + invalid and 1 millisecond will be used instead. +- phy-supply : regulator that powers the Ethernet PHY. +- phy-handle : phandle to the PHY device connected to this device. +- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. + Use instead of phy-handle. +- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports + hw multi queues. Should specify the tx queue number, otherwise set tx queue + number to 1. +- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports + hw multi queues. Should specify the rx queue number, otherwise set rx queue + number to 1. +- fsl,magic-packet : If present, indicates that the hardware supports waking + up via magic packet. + +Optional subnodes: +- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes + according to phy.txt in the same directory + +Example: + +ethernet@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */ + local-mac-address = [00 04 9F 01 1B B9]; + phy-supply = <®_fec_supply>; +}; + +Example with phy specified: + +ethernet@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */ + local-mac-address = [00 04 9F 01 1B B9]; + phy-supply = <®_fec_supply>; + phy-handle = <ðphy>; + mdio { + ethphy: ethernet-phy@6 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <6>; + max-speed = <100>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt new file mode 100644 index 000000000..1e97532a0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -0,0 +1,147 @@ +* MDIO IO device + +The MDIO is a bus to which the PHY devices are connected. For each +device that exists on this bus, a child node should be created. See +the definition of the PHY node in booting-without-of.txt for an example +of how to define a PHY. + +Required properties: + - reg : Offset and length of the register set for the device + - compatible : Should define the compatible device type for the + mdio. Currently supported strings/devices are: + - "fsl,gianfar-tbi" + - "fsl,gianfar-mdio" + - "fsl,etsec2-tbi" + - "fsl,etsec2-mdio" + - "fsl,ucc-mdio" + - "fsl,fman-mdio" + When device_type is "mdio", the following strings are also considered: + - "gianfar" + - "ucc_geth_phy" + +Example: + + mdio@24520 { + reg = <24520 20>; + compatible = "fsl,gianfar-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + +* TBI Internal MDIO bus + +As of this writing, every tsec is associated with an internal TBI PHY. +This PHY is accessed through the local MDIO bus. These buses are defined +similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi". +The TBI PHYs underneath them are similar to normal PHYs, but the reg property +is considered instructive, rather than descriptive. The reg property should +be chosen so it doesn't interfere with other PHYs on the bus. + +* Gianfar-compatible ethernet nodes + +Properties: + + - device_type : Should be "network" + - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" + - compatible : Should be "gianfar" + - reg : Offset and length of the register set for the device + - interrupts : For FEC devices, the first interrupt is the device's + interrupt. For TSEC and eTSEC devices, the first interrupt is + transmit, the second is receive, and the third is error. + - phy-handle : See ethernet.txt file in the same directory. + - fixed-link : See fixed-link.txt in the same directory. + - phy-connection-type : See ethernet.txt file in the same directory. + This property is only really needed if the connection is of type + "rgmii-id", as all other connection types are detected by hardware. + - fsl,magic-packet : If present, indicates that the hardware supports + waking up via magic packet. + - bd-stash : If present, indicates that the hardware supports stashing + buffer descriptors in the L2. + - rx-stash-len : Denotes the number of bytes of a received buffer to stash + in the L2. + - rx-stash-idx : Denotes the index of the first byte from the received + buffer to stash in the L2. + +Example: + ethernet@24000 { + device_type = "network"; + model = "TSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + local-mac-address = [ 00 E0 0C 00 73 00 ]; + interrupts = <29 2 30 2 34 2>; + interrupt-parent = <&mpic>; + phy-handle = <&phy0> + }; + +* Gianfar PTP clock nodes + +General Properties: + + - compatible Should be "fsl,etsec-ptp" + - reg Offset and length of the register set for the device + - interrupts There should be at least two interrupts. Some devices + have as many as four PTP related interrupts. + +Clock Properties: + + - fsl,cksel Timer reference clock source. + - fsl,tclk-period Timer reference clock period in nanoseconds. + - fsl,tmr-prsc Prescaler, divides the output clock. + - fsl,tmr-add Frequency compensation value. + - fsl,tmr-fiper1 Fixed interval period pulse generator. + - fsl,tmr-fiper2 Fixed interval period pulse generator. + - fsl,max-adj Maximum frequency adjustment in parts per billion. + + These properties set the operational parameters for the PTP + clock. You must choose these carefully for the clock to work right. + Here is how to figure good values: + + TimerOsc = selected reference clock MHz + tclk_period = desired clock period nanoseconds + NominalFreq = 1000 / tclk_period MHz + FreqDivRatio = TimerOsc / NominalFreq (must be greater that 1.0) + tmr_add = ceil(2^32 / FreqDivRatio) + OutputClock = NominalFreq / tmr_prsc MHz + PulseWidth = 1 / OutputClock microseconds + FiperFreq1 = desired frequency in Hz + FiperDiv1 = 1000000 * OutputClock / FiperFreq1 + tmr_fiper1 = tmr_prsc * tclk_period * FiperDiv1 - tclk_period + max_adj = 1000000000 * (FreqDivRatio - 1.0) - 1 + + The calculation for tmr_fiper2 is the same as for tmr_fiper1. The + driver expects that tmr_fiper1 will be correctly set to produce a 1 + Pulse Per Second (PPS) signal, since this will be offered to the PPS + subsystem to synchronize the Linux clock. + + Reference clock source is determined by the value, which is holded + in CKSEL bits in TMR_CTRL register. "fsl,cksel" property keeps the + value, which will be directly written in those bits, that is why, + according to reference manual, the next clock sources can be used: + + <0> - external high precision timer reference clock (TSEC_TMR_CLK + input is used for this purpose); + <1> - eTSEC system clock; + <2> - eTSEC1 transmit clock; + <3> - RTC clock input. + + When this attribute is not used, eTSEC system clock will serve as + IEEE 1588 timer reference clock. + +Example: + + ptp_clock@24E00 { + compatible = "fsl,etsec-ptp"; + reg = <0x24E00 0xB0>; + interrupts = <12 0x8 13 0x8>; + interrupt-parent = < &ipic >; + fsl,cksel = <1>; + fsl,tclk-period = <10>; + fsl,tmr-prsc = <100>; + fsl,tmr-add = <0x999999A4>; + fsl,tmr-fiper1 = <0x3B9AC9F6>; + fsl,tmr-fiper2 = <0x00018696>; + fsl,max-adj = <659999998>; + }; diff --git a/Documentation/devicetree/bindings/net/gpmc-eth.txt b/Documentation/devicetree/bindings/net/gpmc-eth.txt new file mode 100644 index 000000000..ace4a64b3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/gpmc-eth.txt @@ -0,0 +1,97 @@ +Device tree bindings for Ethernet chip connected to TI GPMC + +Besides being used to interface with external memory devices, the +General-Purpose Memory Controller can be used to connect Pseudo-SRAM devices +such as ethernet controllers to processors using the TI GPMC as a data bus. + +Ethernet controllers connected to TI GPMC are represented as child nodes of +the GPMC controller with an "ethernet" name. + +All timing relevant properties as well as generic GPMC child properties are +explained in a separate documents. Please refer to +Documentation/devicetree/bindings/bus/ti-gpmc.txt + +For the properties relevant to the ethernet controller connected to the GPMC +refer to the binding documentation of the device. For example, the documentation +for the SMSC 911x is Documentation/devicetree/bindings/net/smsc911x.txt + +Child nodes need to specify the GPMC bus address width using the "bank-width" +property but is possible that an ethernet controller also has a property to +specify the I/O registers address width. Even when the GPMC has a maximum 16-bit +address width, it supports devices with 32-bit word registers. +For example with an SMSC LAN911x/912x controller connected to the TI GPMC on an +OMAP2+ board, "bank-width = <2>;" and "reg-io-width = <4>;". + +Required properties: +- bank-width: Address width of the device in bytes. GPMC supports 8-bit + and 16-bit devices and so must be either 1 or 2 bytes. +- compatible: Compatible string property for the ethernet child device. +- gpmc,cs-on-ns: Chip-select assertion time +- gpmc,cs-rd-off-ns: Chip-select de-assertion time for reads +- gpmc,cs-wr-off-ns: Chip-select de-assertion time for writes +- gpmc,oe-on-ns: Output-enable assertion time +- gpmc,oe-off-ns: Output-enable de-assertion time +- gpmc,we-on-ns: Write-enable assertion time +- gpmc,we-off-ns: Write-enable de-assertion time +- gpmc,access-ns: Start cycle to first data capture (read access) +- gpmc,rd-cycle-ns: Total read cycle time +- gpmc,wr-cycle-ns: Total write cycle time +- reg: Chip-select, base address (relative to chip-select) + and size of the memory mapped for the device. + Note that base address will be typically 0 as this + is the start of the chip-select. + +Optional properties: +- gpmc,XXX Additional GPMC timings and settings parameters. See + Documentation/devicetree/bindings/bus/ti-gpmc.txt + +Example: + +gpmc: gpmc@6e000000 { + compatible = "ti,omap3430-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x6e000000 0x1000>; + interrupts = <20>; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <5 0 0x2c000000 0x1000000>; + + ethernet@5,0 { + compatible = "smsc,lan9221", "smsc,lan9115"; + reg = <5 0 0xff>; + bank-width = <2>; + + gpmc,mux-add-data; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <186>; + gpmc,cs-wr-off-ns = <186>; + gpmc,adv-on-ns = <12>; + gpmc,adv-rd-off-ns = <48>; + gpmc,adv-wr-off-ns = <48>; + gpmc,oe-on-ns = <54>; + gpmc,oe-off-ns = <168>; + gpmc,we-on-ns = <54>; + gpmc,we-off-ns = <168>; + gpmc,rd-cycle-ns = <186>; + gpmc,wr-cycle-ns = <186>; + gpmc,access-ns = <114>; + gpmc,page-burst-access-ns = <6>; + gpmc,bus-turnaround-ns = <12>; + gpmc,cycle2cycle-delay-ns = <18>; + gpmc,wr-data-mux-bus-ns = <90>; + gpmc,wr-access-ns = <186>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + + interrupt-parent = <&gpio6>; + interrupts = <16>; + vmmc-supply = <&vddvario>; + vmmc_aux-supply = <&vdd33a>; + reg-io-width = <4>; + + smsc,save-mac-address; + }; +}; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt new file mode 100644 index 000000000..988fc694b --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt @@ -0,0 +1,88 @@ +Hisilicon hip04 Ethernet Controller + +* Ethernet controller node + +Required properties: +- compatible: should be "hisilicon,hip04-mac". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device. +- port-handle: <phandle port channel> + phandle, specifies a reference to the syscon ppe node + port, port number connected to the controller + channel, recv channel start from channel * number (RX_DESC_NUM) +- phy-mode: see ethernet.txt [1]. + +Optional properties: +- phy-handle: see ethernet.txt [1]. + +[1] Documentation/devicetree/bindings/net/ethernet.txt + + +* Ethernet ppe node: +Control rx & tx fifos of all ethernet controllers. +Have 2048 recv channels shared by all ethernet controllers, only if no overlap. +Each controller's recv channel start from channel * number (RX_DESC_NUM). + +Required properties: +- compatible: "hisilicon,hip04-ppe", "syscon". +- reg: address and length of the register set for the device. + + +* MDIO bus node: + +Required properties: + +- compatible: should be "hisilicon,hip04-mdio". +- Inherits from MDIO bus node binding [2] +[2] Documentation/devicetree/bindings/net/phy.txt + +Example: + mdio { + compatible = "hisilicon,hip04-mdio"; + reg = <0x28f1000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + marvell,reg-init = <18 0x14 0 0x8001>; + }; + + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + marvell,reg-init = <18 0x14 0 0x8001>; + }; + }; + + ppe: ppe@28c0000 { + compatible = "hisilicon,hip04-ppe", "syscon"; + reg = <0x28c0000 0x10000>; + }; + + fe: ethernet@28b0000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x28b0000 0x10000>; + interrupts = <0 413 4>; + phy-mode = "mii"; + port-handle = <&ppe 31 0>; + }; + + ge0: ethernet@2800000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x2800000 0x10000>; + interrupts = <0 402 4>; + phy-mode = "sgmii"; + port-handle = <&ppe 0 1>; + phy-handle = <&phy0>; + }; + + ge8: ethernet@2880000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x2880000 0x10000>; + interrupts = <0 410 4>; + phy-mode = "sgmii"; + port-handle = <&ppe 8 2>; + phy-handle = <&phy1>; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt new file mode 100644 index 000000000..75d398bb1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt @@ -0,0 +1,36 @@ +Hisilicon hix5hd2 gmac controller + +Required properties: +- compatible: should be "hisilicon,hix5hd2-gmac". +- reg: specifies base physical address(s) and size of the device registers. + The first region is the MAC register base and size. + The second region is external interface control register. +- interrupts: should contain the MAC interrupt. +- #address-cells: must be <1>. +- #size-cells: must be <0>. +- phy-mode: see ethernet.txt [1]. +- phy-handle: see ethernet.txt [1]. +- mac-address: see ethernet.txt [1]. +- clocks: clock phandle and specifier pair. + +- PHY subnode: inherits from phy binding [2] + +[1] Documentation/devicetree/bindings/net/ethernet.txt +[2] Documentation/devicetree/bindings/net/phy.txt + +Example: + gmac0: ethernet@f9840000 { + compatible = "hisilicon,hix5hd2-gmac"; + reg = <0xf9840000 0x1000>,<0xf984300c 0x4>; + interrupts = <0 71 4>; + #address-cells = <1>; + #size-cells = <0>; + phy-mode = "mii"; + phy-handle = <&phy2>; + mac-address = [00 00 00 00 00 00]; + clocks = <&clock HIX5HD2_MAC0_CLK>; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt new file mode 100644 index 000000000..168f1be50 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt @@ -0,0 +1,27 @@ +* AT86RF230 IEEE 802.15.4 * + +Required properties: + - compatible: should be "atmel,at86rf230", "atmel,at86rf231", + "atmel,at86rf233" or "atmel,at86rf212" + - spi-max-frequency: maximal bus speed, should be set to 7500000 depends + sync or async operation mode + - reg: the chipselect index + - interrupts: the interrupt generated by the device. Non high-level + can occur deadlocks while handling isr. + +Optional properties: + - reset-gpio: GPIO spec for the rstn pin + - sleep-gpio: GPIO spec for the slp_tr pin + - xtal-trim: u8 value for fine tuning the internal capacitance + arrays of xtal pins: 0 = +0 pF, 0xf = +4.5 pF + +Example: + + at86rf231@0 { + compatible = "atmel,at86rf231"; + spi-max-frequency = <7500000>; + reg = <0>; + interrupts = <19 4>; + interrupt-parent = <&gpio3>; + xtal-trim = /bits/ 8 <0x06>; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt new file mode 100644 index 000000000..fb6d49f18 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt @@ -0,0 +1,33 @@ +*CC2520 IEEE 802.15.4 Compatible Radio* + +Required properties: + - compatible: should be "ti,cc2520" + - spi-max-frequency: maximal bus speed (8000000), should be set to 4000000 depends + sync or async operation mode + - reg: the chipselect index + - pinctrl-0: pin control group to be used for this controller. + - pinctrl-names: must contain a "default" entry. + - fifo-gpio: GPIO spec for the FIFO pin + - fifop-gpio: GPIO spec for the FIFOP pin + - sfd-gpio: GPIO spec for the SFD pin + - cca-gpio: GPIO spec for the CCA pin + - vreg-gpio: GPIO spec for the VREG pin + - reset-gpio: GPIO spec for the RESET pin +Optional properties: + - amplified: include if the CC2520 is connected to a CC2591 amplifier + +Example: + cc2520@0 { + compatible = "ti,cc2520"; + reg = <0>; + spi-max-frequency = <4000000>; + amplified; + pinctrl-names = "default"; + pinctrl-0 = <&cc2520_cape_pins>; + fifo-gpio = <&gpio1 18 0>; + fifop-gpio = <&gpio1 19 0>; + sfd-gpio = <&gpio1 13 0>; + cca-gpio = <&gpio1 16 0>; + vreg-gpio = <&gpio0 31 0>; + reset-gpio = <&gpio1 12 0>; + }; diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt new file mode 100644 index 000000000..d0e6fa38f --- /dev/null +++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt @@ -0,0 +1,217 @@ +This document describes the device tree bindings associated with the +keystone network coprocessor(NetCP) driver support. + +The network coprocessor (NetCP) is a hardware accelerator that processes +Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsytem with a ethernet +switch sub-module to send and receive packets. NetCP also includes a packet +accelerator (PA) module to perform packet classification operations such as +header matching, and packet modification operations such as checksum +generation. NetCP can also optionally include a Security Accelerator (SA) +capable of performing IPSec operations on ingress/egress packets. + +Keystone II SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which +includes a 3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates +per Ethernet port. + +Keystone NetCP driver has a plug-in module architecture where each of the NetCP +sub-modules exist as a loadable kernel module which plug in to the netcp core. +These sub-modules are represented as "netcp-devices" in the dts bindings. It is +mandatory to have the ethernet switch sub-module for the ethernet interface to +be operational. Any other sub-module like the PA is optional. + +NetCP Ethernet SubSystem Layout: + +----------------------------- + NetCP subsystem(10G or 1G) +----------------------------- + | + |-> NetCP Devices -> | + | |-> GBE/XGBE Switch + | | + | |-> Packet Accelerator + | | + | |-> Security Accelerator + | + | + | + |-> NetCP Interfaces -> | + |-> Ethernet Port 0 + | + |-> Ethernet Port 1 + | + |-> Ethernet Port 2 + | + |-> Ethernet Port 3 + + +NetCP subsystem properties: +Required properties: +- compatible: Should be "ti,netcp-1.0" +- clocks: phandle to the reference clocks for the subsystem. +- dma-id: Navigator packet dma instance id. +- ranges: address range of NetCP (includes, Ethernet SS, PA and SA) + +Optional properties: +- reg: register location and the size for the following register + regions in the specified order. + - Efuse MAC address register +- dma-coherent: Present if dma operations are coherent +- big-endian: Keystone devices can be operated in a mode where the DSP is in + the big endian mode. In such cases enable this option. This + option should also be enabled if the ARM is operated in + big endian mode with the DSP in little endian. + +NetCP device properties: Device specification for NetCP sub-modules. +1Gb/10Gb (gbe/xgbe) ethernet switch sub-module specifications. +Required properties: +- label: Must be "netcp-gbe" for 1Gb & "netcp-xgbe" for 10Gb. +- compatible: Must be one of below:- + "ti,netcp-gbe" for 1GbE on NetCP 1.4 + "ti,netcp-gbe-5" for 1GbE N NetCP 1.5 (N=5) + "ti,netcp-gbe-9" for 1GbE N NetCP 1.5 (N=9) + "ti,netcp-gbe-2" for 1GbE N NetCP 1.5 (N=2) + "ti,netcp-xgbe" for 10 GbE + +- reg: register location and the size for the following register + regions in the specified order. + - switch subsystem registers + - sgmii port3/4 module registers (only for NetCP 1.4) + - switch module registers + - serdes registers (only for 10G) + + NetCP 1.4 ethss, here is the order + index #0 - switch subsystem registers + index #1 - sgmii port3/4 module registers + index #2 - switch module registers + + NetCP 1.5 ethss 9 port, 5 port and 2 port + index #0 - switch subsystem registers + index #1 - switch module registers + index #2 - serdes registers + +- tx-channel: the navigator packet dma channel name for tx. +- tx-queue: the navigator queue number associated with the tx dma channel. +- interfaces: specification for each of the switch port to be registered as a + network interface in the stack. +-- slave-port: Switch port number, 0 based numbering. +-- link-interface: type of link interface, supported options are + - mac<->mac auto negotiate mode: 0 + - mac<->phy mode: 1 + - mac<->mac forced mode: 2 + - mac<->fiber mode: 3 + - mac<->phy mode with no mdio: 4 + - 10Gb mac<->phy mode : 10 + - 10Gb mac<->mac forced mode : 11 +----phy-handle: phandle to PHY device + +Optional properties: +- enable-ale: NetCP driver keeps the address learning feature in the ethernet + switch module disabled. This attribute is to enable the address + learning. +- secondary-slave-ports: specification for each of the switch port not be + registered as a network interface. NetCP driver + will only initialize these ports and attach PHY + driver to them if needed. + +NetCP interface properties: Interface specification for NetCP sub-modules. +Required properties: +- rx-channel: the navigator packet dma channel name for rx. +- rx-queue: the navigator queue number associated with rx dma channel. +- rx-pool: specifies the number of descriptors to be used & the region-id + for creating the rx descriptor pool. +- tx-pool: specifies the number of descriptors to be used & the region-id + for creating the tx descriptor pool. +- rx-queue-depth: number of descriptors in each of the free descriptor + queue (FDQ) for the pktdma Rx flow. There can be at + present a maximum of 4 queues per Rx flow. +- rx-buffer-size: the buffer size for each of the Rx flow FDQ. +- tx-completion-queue: the navigator queue number where the descriptors are + recycled after Tx DMA completion. + +Optional properties: +- efuse-mac: If this is 1, then the MAC address for the interface is + obtained from the device efuse mac address register +- local-mac-address: the driver is designed to use the of_get_mac_address api + only if efuse-mac is 0. When efuse-mac is 0, the MAC + address is obtained from local-mac-address. If this + attribute is not present, then the driver will use a + random MAC address. +- "netcp-device label": phandle to the device specification for each of NetCP + sub-module attached to this interface. + +Example binding: + +netcp: netcp@2000000 { + reg = <0x2620110 0x8>; + reg-names = "efuse"; + compatible = "ti,netcp-1.0"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000000 0xfffff>; + clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>; + dma-coherent; + /* big-endian; */ + dma-id = <0>; + + netcp-devices { + #address-cells = <1>; + #size-cells = <1>; + ranges; + gbe@90000 { + label = "netcp-gbe"; + reg = <0x90000 0x300>, <0x90400 0x400>, <0x90800 0x700>; + /* enable-ale; */ + tx-queue = <648>; + tx-channel = <8>; + + interfaces { + gbe0: interface-0 { + slave-port = <0>; + link-interface = <4>; + }; + gbe1: interface-1 { + slave-port = <1>; + link-interface = <4>; + }; + }; + + secondary-slave-ports { + port-2 { + slave-port = <2>; + link-interface = <2>; + }; + port-3 { + slave-port = <3>; + link-interface = <2>; + }; + }; + }; + }; + + netcp-interfaces { + interface-0 { + rx-channel = <22>; + rx-pool = <1024 12>; + tx-pool = <1024 12>; + rx-queue-depth = <128 128 0 0>; + rx-buffer-size = <1518 4096 0 0>; + rx-queue = <8704>; + tx-completion-queue = <8706>; + efuse-mac = <1>; + netcp-gbe = <&gbe0>; + + }; + interface-1 { + rx-channel = <23>; + rx-pool = <1024 12>; + tx-pool = <1024 12>; + rx-queue-depth = <128 128 0 0>; + rx-buffer-size = <1518 4096 0 0>; + rx-queue = <8705>; + tx-completion-queue = <8707>; + efuse-mac = <0>; + local-mac-address = [02 18 31 7e 3e 6f]; + netcp-gbe = <&gbe1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/lpc-eth.txt b/Documentation/devicetree/bindings/net/lpc-eth.txt new file mode 100644 index 000000000..b92e92780 --- /dev/null +++ b/Documentation/devicetree/bindings/net/lpc-eth.txt @@ -0,0 +1,23 @@ +* NXP LPC32xx SoC Ethernet Controller + +Required properties: +- compatible: Should be "nxp,lpc-eth" +- reg: Address and length of the register set for the device +- interrupts: Should contain ethernet controller interrupt + +Optional properties: +- phy-mode: See ethernet.txt file in the same directory. If the property is + absent, "rmii" is assumed. +- use-iram: Use LPC32xx internal SRAM (IRAM) for DMA buffering + +Example: + + mac: ethernet@31060000 { + compatible = "nxp,lpc-eth"; + reg = <0x31060000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <29 0>; + + phy-mode = "rmii"; + use-iram; + }; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt new file mode 100644 index 000000000..ba19d671e --- /dev/null +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -0,0 +1,30 @@ +* Cadence MACB/GEM Ethernet controller + +Required properties: +- compatible: Should be "cdns,[<chip>-]{macb|gem}" + Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs or the 10/100Mbit IP + available on sama5d3 SoCs. + Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". + Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on + the Cadence GEM, or the generic form: "cdns,gem". + Use "cdns,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs. + Use "cdns,sama5d4-gem" for the Gigabit IP available on Atmel sama5d4 SoCs. +- reg: Address and length of the register set for the device +- interrupts: Should contain macb interrupt +- phy-mode: See ethernet.txt file in the same directory. +- clock-names: Tuple listing input clock names. + Required elements: 'pclk', 'hclk' + Optional elements: 'tx_clk' +- clocks: Phandles to input clocks. + +Examples: + + macb0: ethernet@fffc4000 { + compatible = "cdns,at32ap7000-macb"; + reg = <0xfffc4000 0x4000>; + interrupts = <21>; + phy-mode = "rmii"; + local-mac-address = [3a 0e 03 04 05 06]; + clock-names = "pclk", "hclk", "tx_clk"; + clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>; + }; diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt new file mode 100644 index 000000000..f5a8ca29a --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -0,0 +1,21 @@ +* Marvell Armada 370 / Armada XP Ethernet Controller (NETA) + +Required properties: +- compatible: "marvell,armada-370-neta" or "marvell,armada-xp-neta". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device +- phy: See ethernet.txt file in the same directory. +- phy-mode: See ethernet.txt file in the same directory +- clocks: a pointer to the reference clock for this device. + +Example: + +ethernet@d0070000 { + compatible = "marvell,armada-370-neta"; + reg = <0xd0070000 0x2500>; + interrupts = <8>; + clocks = <&gate_clk 4>; + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt new file mode 100644 index 000000000..9417e54c2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt @@ -0,0 +1,39 @@ +* Marvell MDIO Ethernet Controller interface + +The Ethernet controllers of the Marvel Kirkwood, Dove, Orion5x, +MV78xx0, Armada 370 and Armada XP have an identical unit that provides +an interface with the MDIO bus. This driver handles this MDIO +interface. + +Required properties: +- compatible: "marvell,orion-mdio" +- reg: address and length of the SMI register + +Optional properties: +- interrupts: interrupt line number for the SMI error/done interrupt +- clocks: Phandle to the clock control device and gate bit + +The child nodes of the MDIO driver are the individual PHY devices +connected to this MDIO bus. They must have a "reg" property given the +PHY address on the MDIO bus. + +Example at the SoC level: + +mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; + reg = <0xd0072004 0x4>; +}; + +And at the board level: + +mdio { + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +} diff --git a/Documentation/devicetree/bindings/net/marvell-orion-net.txt b/Documentation/devicetree/bindings/net/marvell-orion-net.txt new file mode 100644 index 000000000..bce52b2ec --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-orion-net.txt @@ -0,0 +1,82 @@ +Marvell Orion/Discovery ethernet controller +============================================= + +The Marvell Discovery ethernet controller can be found on Marvell Orion SoCs +(Kirkwood, Dove, Orion5x, and Discovery Innovation) and as part of Marvell +Discovery system controller chips (mv64[345]60). + +The Discovery ethernet controller is described with two levels of nodes. The +first level describes the ethernet controller itself and the second level +describes up to 3 ethernet port nodes within that controller. The reason for +the multiple levels is that the port registers are interleaved within a single +set of controller registers. Each port node describes port-specific properties. + +Note: The above separation is only true for Discovery system controllers. +For Orion SoCs we stick to the separation, although there each controller has +only one port associated. Multiple ports are implemented as multiple single-port +controllers. As Kirkwood has some issues with proper initialization after reset, +an extra compatible string is added for it. + +* Ethernet controller node + +Required controller properties: + - #address-cells: shall be 1. + - #size-cells: shall be 0. + - compatible: shall be one of "marvell,orion-eth", "marvell,kirkwood-eth". + - reg: address and length of the controller registers. + +Optional controller properties: + - clocks: phandle reference to the controller clock. + - marvell,tx-checksum-limit: max tx packet size for hardware checksum. + +* Ethernet port node + +Required port properties: + - compatible: shall be one of "marvell,orion-eth-port", + "marvell,kirkwood-eth-port". + - reg: port number relative to ethernet controller, shall be 0, 1, or 2. + - interrupts: port interrupt. + - local-mac-address: See ethernet.txt file in the same directory. + +Optional port properties: + - marvell,tx-queue-size: size of the transmit ring buffer. + - marvell,tx-sram-addr: address of transmit descriptor buffer located in SRAM. + - marvell,tx-sram-size: size of transmit descriptor buffer located in SRAM. + - marvell,rx-queue-size: size of the receive ring buffer. + - marvell,rx-sram-addr: address of receive descriptor buffer located in SRAM. + - marvell,rx-sram-size: size of receive descriptor buffer located in SRAM. + +and + + - phy-handle: See ethernet.txt file in the same directory. + +or + + - speed: port speed if no PHY connected. + - duplex: port mode if no PHY connected. + +* Node example: + +mdio-bus { + ... + ethphy: ethernet-phy@8 { + ... + }; +}; + +eth: ethernet-controller@72000 { + compatible = "marvell,orion-eth"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72000 0x2000>; + clocks = <&gate_clk 2>; + marvell,tx-checksum-limit = <1600>; + + ethernet@0 { + compatible = "marvell,orion-eth-port"; + reg = <0>; + interrupts = <29>; + phy-handle = <ðphy>; + local-mac-address = [00 00 00 00 00 00]; + }; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt new file mode 100644 index 000000000..aa4f4230b --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -0,0 +1,61 @@ +* Marvell Armada 375 Ethernet Controller (PPv2) + +Required properties: + +- compatible: should be "marvell,armada-375-pp2" +- reg: addresses and length of the register sets for the device. + Must contain the following register sets: + - common controller registers + - LMS registers + In addition, at least one port register set is required. +- clocks: a pointer to the reference clocks for this device, consequently: + - main controller clock + - GOP clock +- clock-names: names of used clocks, must be "pp_clk" and "gop_clk". + +The ethernet ports are represented by subnodes. At least one port is +required. + +Required properties (port): + +- interrupts: interrupt for the port +- port-id: should be '0' or '1' for ethernet ports, and '2' for the + loopback port +- phy-mode: See ethernet.txt file in the same directory + +Optional properties (port): + +- marvell,loopback: port is loopback mode +- phy: a phandle to a phy node defining the PHY address (as the reg + property, a single integer). Note: if this property isn't present, + then fixed link is assumed, and the 'fixed-link' property is + mandatory. + +Example: + +ethernet@f0000 { + compatible = "marvell,armada-375-pp2"; + reg = <0xf0000 0xa000>, + <0xc0000 0x3060>, + <0xc4000 0x100>, + <0xc5000 0x100>; + clocks = <&gateclk 3>, <&gateclk 19>; + clock-names = "pp_clk", "gop_clk"; + status = "okay"; + + eth0: eth0@c4000 { + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + port-id = <0>; + status = "okay"; + phy = <&phy0>; + phy-mode = "gmii"; + }; + + eth1: eth1@c5000 { + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + port-id = <1>; + status = "okay"; + phy = <&phy3>; + phy-mode = "gmii"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-pxa168.txt b/Documentation/devicetree/bindings/net/marvell-pxa168.txt new file mode 100644 index 000000000..845a148a3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-pxa168.txt @@ -0,0 +1,36 @@ +* Marvell PXA168 Ethernet Controller + +Required properties: +- compatible: should be "marvell,pxa168-eth". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device. +- clocks: pointer to the clock for the device. + +Optional properties: +- port-id: Ethernet port number. Should be '0','1' or '2'. +- #address-cells: must be 1 when using sub-nodes. +- #size-cells: must be 0 when using sub-nodes. +- phy-handle: see ethernet.txt file in the same directory. +- local-mac-address: see ethernet.txt file in the same directory. + +Sub-nodes: +Each PHY can be represented as a sub-node. This is not mandatory. + +Sub-nodes required properties: +- reg: the MDIO address of the PHY. + +Example: + + eth0: ethernet@f7b90000 { + compatible = "marvell,pxa168-eth"; + reg = <0xf7b90000 0x10000>; + clocks = <&chip CLKID_GETH0>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + phy-handle = <ðphy0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt new file mode 100644 index 000000000..8dbcf8295 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt @@ -0,0 +1,26 @@ +MDIO on GPIOs + +Currently defined compatibles: +- virtual,gpio-mdio + +MDC and MDIO lines connected to GPIO controllers are listed in the +gpios property as described in section VIII.1 in the following order: + +MDC, MDIO. + +Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases" +node. + +Example: + +aliases { + mdio-gpio0 = &mdio0; +}; + +mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qe_pio_a 11 + &qe_pio_c 6>; +}; diff --git a/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt new file mode 100644 index 000000000..79384113c --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt @@ -0,0 +1,127 @@ +Properties for an MDIO bus multiplexer/switch controlled by GPIO pins. + +This is a special case of a MDIO bus multiplexer. One or more GPIO +lines are used to control which child bus is connected. + +Required properties in addition to the generic multiplexer properties: + +- compatible : mdio-mux-gpio. +- gpios : GPIO specifiers for each GPIO line. One or more must be specified. + + +Example : + + /* The parent MDIO bus. */ + smi1: mdio@1180000001900 { + compatible = "cavium,octeon-3860-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0x00001900 0x0 0x40>; + }; + + /* + An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a + pair of GPIO lines. Child busses 2 and 3 populated with 4 + PHYs each. + */ + mdio-mux { + compatible = "mdio-mux-gpio"; + gpios = <&gpio1 3 0>, <&gpio1 4 0>; + mdio-parent-bus = <&smi1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy11: ethernet-phy@1 { + reg = <1>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy12: ethernet-phy@2 { + reg = <2>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy13: ethernet-phy@3 { + reg = <3>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy14: ethernet-phy@4 { + reg = <4>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + }; + + mdio@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + phy21: ethernet-phy@1 { + reg = <1>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy22: ethernet-phy@2 { + reg = <2>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy23: ethernet-phy@3 { + reg = <3>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy24: ethernet-phy@4 { + reg = <4>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt new file mode 100644 index 000000000..8516929c7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt @@ -0,0 +1,75 @@ +Properties for an MDIO bus multiplexer controlled by a memory-mapped device + +This is a special case of a MDIO bus multiplexer. A memory-mapped device, +like an FPGA, is used to control which child bus is connected. The mdio-mux +node must be a child of the memory-mapped device. The driver currently only +supports devices with eight-bit registers. + +Required properties in addition to the generic multiplexer properties: + +- compatible : string, must contain "mdio-mux-mmioreg" + +- reg : integer, contains the offset of the register that controls the bus + multiplexer. The size field in the 'reg' property is the size of + register, and must therefore be 1. + +- mux-mask : integer, contains an eight-bit mask that specifies which + bits in the register control the actual bus multiplexer. The + 'reg' property of each child mdio-mux node must be constrained by + this mask. + +Example: + +The FPGA node defines a memory-mapped FPGA with a register space of 0x30 bytes. +For the "EMI2" MDIO bus, register 9 (BRDCFG1) controls the mux on that bus. +A bitmask of 0x6 means that bits 1 and 2 (bit 0 is lsb) are the bits on +BRDCFG1 that control the actual mux. + + /* The FPGA node */ + fpga: board-control@3,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p5020ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; + ranges = <0 3 0 0x30>; + + mdio-mux-emi2 { + compatible = "mdio-mux-mmioreg", "mdio-mux"; + mdio-parent-bus = <&xmdio0>; + #address-cells = <1>; + #size-cells = <0>; + reg = <9 1>; // BRDCFG1 + mux-mask = <0x6>; // EMI2 + + emi2_slot1: mdio@0 { // Slot 1 XAUI (FM2) + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + phy_xgmii_slot1: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <4>; + }; + }; + + emi2_slot2: mdio@2 { // Slot 2 XAUI (FM1) + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy_xgmii_slot2: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0>; + }; + }; + }; + }; + + /* The parent MDIO bus. */ + xmdio0: mdio@f1000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,fman-xmdio"; + reg = <0xf1000 0x1000>; + interrupts = <100 1 0 0>; + }; diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt new file mode 100644 index 000000000..f65606f8d --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux.txt @@ -0,0 +1,136 @@ +Common MDIO bus multiplexer/switch properties. + +An MDIO bus multiplexer/switch will have several child busses that are +numbered uniquely in a device dependent manner. The nodes for an MDIO +bus multiplexer/switch will have one child node for each child bus. + +Required properties: +- mdio-parent-bus : phandle to the parent MDIO bus. +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Other properties specific to the multiplexer/switch hardware. + +Required properties for child nodes: +- #address-cells = <1>; +- #size-cells = <0>; +- reg : The sub-bus number. + + +Example : + + /* The parent MDIO bus. */ + smi1: mdio@1180000001900 { + compatible = "cavium,octeon-3860-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0x00001900 0x0 0x40>; + }; + + /* + An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a + pair of GPIO lines. Child busses 2 and 3 populated with 4 + PHYs each. + */ + mdio-mux { + compatible = "mdio-mux-gpio"; + gpios = <&gpio1 3 0>, <&gpio1 4 0>; + mdio-parent-bus = <&smi1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy11: ethernet-phy@1 { + reg = <1>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy12: ethernet-phy@2 { + reg = <2>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy13: ethernet-phy@3 { + reg = <3>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy14: ethernet-phy@4 { + reg = <4>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + }; + + mdio@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + phy21: ethernet-phy@1 { + reg = <1>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy22: ethernet-phy@2 { + reg = <2>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy23: ethernet-phy@3 { + reg = <3>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy24: ethernet-phy@4 { + reg = <4>; + compatible = "marvell,88e1149r"; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/meson-dwmac.txt b/Documentation/devicetree/bindings/net/meson-dwmac.txt new file mode 100644 index 000000000..ec633d74a --- /dev/null +++ b/Documentation/devicetree/bindings/net/meson-dwmac.txt @@ -0,0 +1,25 @@ +* Amlogic Meson DWMAC Ethernet controller + +The device inherits all the properties of the dwmac/stmmac devices +described in the file net/stmmac.txt with the following changes. + +Required properties: + +- compatible: should be "amlogic,meson6-dwmac" along with "snps,dwmac" + and any applicable more detailed version number + described in net/stmmac.txt + +- reg: should contain a register range for the dwmac controller and + another one for the Amlogic specific configuration + +Example: + + ethmac: ethernet@c9410000 { + compatible = "amlogic,meson6-dwmac", "snps,dwmac"; + reg = <0xc9410000 0x10000 + 0xc1108108 0x4>; + interrupts = <0 8 1>; + interrupt-names = "macirq"; + clocks = <&clk81>; + clock-names = "stmmaceth"; + } diff --git a/Documentation/devicetree/bindings/net/micrel-ks8851.txt b/Documentation/devicetree/bindings/net/micrel-ks8851.txt new file mode 100644 index 000000000..bbdf9a735 --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel-ks8851.txt @@ -0,0 +1,18 @@ +Micrel KS8851 Ethernet mac (MLL) + +Required properties: +- compatible = "micrel,ks8851-mll" of parallel interface +- reg : 2 physical address and size of registers for data and command +- interrupts : interrupt connection + +Micrel KS8851 Ethernet mac (SPI) + +Required properties: +- compatible = "micrel,ks8851" or the deprecated "ks8851" +- reg : chip select number +- interrupts : interrupt connection + +Optional properties: +- vdd-supply: analog 3.3V supply for Ethernet mac +- vdd-io-supply: digital 1.8V IO supply for Ethernet mac +- reset-gpios: reset_n input pin diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt new file mode 100644 index 000000000..692076fda --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -0,0 +1,83 @@ +Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY + +Some boards require special tuning values, particularly when it comes to +clock delays. You can specify clock delay values by adding +micrel-specific properties to an Ethernet OF device node. + +Note that these settings are applied after any phy-specific fixup from +phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c), +and therefore may overwrite them. + +KSZ9021: + + All skew control options are specified in picoseconds. The minimum + value is 0, the maximum value is 3000, and it is incremented by 200ps + steps. + + Optional properties: + + - rxc-skew-ps : Skew control of RXC pad + - rxdv-skew-ps : Skew control of RX CTL pad + - txc-skew-ps : Skew control of TXC pad + - txen-skew-ps : Skew control of TX CTL pad + - rxd0-skew-ps : Skew control of RX data 0 pad + - rxd1-skew-ps : Skew control of RX data 1 pad + - rxd2-skew-ps : Skew control of RX data 2 pad + - rxd3-skew-ps : Skew control of RX data 3 pad + - txd0-skew-ps : Skew control of TX data 0 pad + - txd1-skew-ps : Skew control of TX data 1 pad + - txd2-skew-ps : Skew control of TX data 2 pad + - txd3-skew-ps : Skew control of TX data 3 pad + +KSZ9031: + + All skew control options are specified in picoseconds. The minimum + value is 0, and the maximum is property-dependent. The increment + step is 60ps. + + Optional properties: + + Maximum value of 1860: + + - rxc-skew-ps : Skew control of RX clock pad + - txc-skew-ps : Skew control of TX clock pad + + Maximum value of 900: + + - rxdv-skew-ps : Skew control of RX CTL pad + - txen-skew-ps : Skew control of TX CTL pad + - rxd0-skew-ps : Skew control of RX data 0 pad + - rxd1-skew-ps : Skew control of RX data 1 pad + - rxd2-skew-ps : Skew control of RX data 2 pad + - rxd3-skew-ps : Skew control of RX data 3 pad + - txd0-skew-ps : Skew control of TX data 0 pad + - txd1-skew-ps : Skew control of TX data 1 pad + - txd2-skew-ps : Skew control of TX data 2 pad + - txd3-skew-ps : Skew control of TX data 3 pad + +Examples: + + /* Attach to an Ethernet device with autodetected PHY */ + &enet { + rxc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + txc-skew-ps = <3000>; + txen-skew-ps = <0>; + status = "okay"; + }; + + /* Attach to an explicitly-specified PHY */ + mdio { + phy0: ethernet-phy@0 { + rxc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + txc-skew-ps = <3000>; + txen-skew-ps = <0>; + reg = <0>; + }; + }; + ethernet@70000 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt new file mode 100644 index 000000000..87496a8c6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel.txt @@ -0,0 +1,37 @@ +Micrel PHY properties. + +These properties cover the base properties Micrel PHYs. + +Optional properties: + + - micrel,led-mode : LED mode value to set for PHYs with configurable LEDs. + + Configure the LED mode with single value. The list of PHYs and the + bits that are currently supported: + + KSZ8001: register 0x1e, bits 15..14 + KSZ8041: register 0x1e, bits 15..14 + KSZ8021: register 0x1f, bits 5..4 + KSZ8031: register 0x1f, bits 5..4 + KSZ8051: register 0x1f, bits 5..4 + KSZ8081: register 0x1f, bits 5..4 + KSZ8091: register 0x1f, bits 5..4 + + See the respective PHY datasheet for the mode values. + + - micrel,rmii-reference-clock-select-25-mhz: RMII Reference Clock Select + bit selects 25 MHz mode + + Setting the RMII Reference Clock Select bit enables 25 MHz rather + than 50 MHz clock mode. + + Note that this option in only needed for certain PHY revisions with a + non-standard, inverted function of this configuration bit. + Specifically, a clock reference ("rmii-ref" below) is always needed to + actually select a mode. + + - clocks, clock-names: contains clocks according to the common clock bindings. + + supported clocks: + - KSZ8021, KSZ8031, KSZ8081, KSZ8091: "rmii-ref": The RMII reference + input clock. Used to determine the XI input clock. diff --git a/Documentation/devicetree/bindings/net/moxa,moxart-mac.txt b/Documentation/devicetree/bindings/net/moxa,moxart-mac.txt new file mode 100644 index 000000000..583418b2c --- /dev/null +++ b/Documentation/devicetree/bindings/net/moxa,moxart-mac.txt @@ -0,0 +1,21 @@ +MOXA ART Ethernet Controller + +Required properties: + +- compatible : Must be "moxa,moxart-mac" +- reg : Should contain register location and length +- interrupts : Should contain the mac interrupt number + +Example: + + mac0: mac@90900000 { + compatible = "moxa,moxart-mac"; + reg = <0x90900000 0x100>; + interrupts = <25 0>; + }; + + mac1: mac@92000000 { + compatible = "moxa,moxart-mac"; + reg = <0x92000000 0x100>; + interrupts = <27 0>; + }; diff --git a/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt new file mode 100644 index 000000000..5b6cd9b3f --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt @@ -0,0 +1,35 @@ +* NXP Semiconductors NXP NCI NFC Controllers + +Required properties: +- compatible: Should be "nxp,nxp-nci-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the chip +- firmware-gpios: Output GPIO pin used to enter firmware download mode + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with NPC100 NFC controller on I2C2): + +&i2c2 { + + status = "okay"; + + npc100: npc100@29 { + + compatible = "nxp,nxp-nci-i2c"; + + reg = <0x29>; + clock-frequency = <100000>; + + interrupt-parent = <&gpio1>; + interrupts = <29 GPIO_ACTIVE_HIGH>; + + enable-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/pn544.txt b/Documentation/devicetree/bindings/net/nfc/pn544.txt new file mode 100644 index 000000000..dab69f361 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/pn544.txt @@ -0,0 +1,35 @@ +* NXP Semiconductors PN544 NFC Controller + +Required properties: +- compatible: Should be "nxp,pn544-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the PN544 +- firmware-gpios: Output GPIO pin used to enter firmware download mode + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with PN544 on I2C2): + +&i2c2 { + + status = "okay"; + + pn544: pn544@28 { + + compatible = "nxp,pn544-i2c"; + + reg = <0x28>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio1>; + interrupts = <17 GPIO_ACTIVE_HIGH>; + + enable-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt new file mode 100644 index 000000000..7bb2e213d --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt @@ -0,0 +1,40 @@ +* STMicroelectronics SAS. ST21NFCA NFC Controller + +Required properties: +- compatible: Should be "st,st21nfca-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the ST21NFCA + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2): + +&i2c2 { + + status = "okay"; + + st21nfca: st21nfca@1 { + + compatible = "st,st21nfca-i2c"; + + reg = <0x01>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + + enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt new file mode 100644 index 000000000..bb237072d --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st21nfcb.txt @@ -0,0 +1,33 @@ +* STMicroelectronics SAS. ST21NFCB NFC Controller + +Required properties: +- compatible: Should be "st,st21nfcb-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- reset-gpios: Output GPIO pin used to reset the ST21NFCB + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): + +&i2c2 { + + status = "okay"; + + st21nfcb: st21nfcb@8 { + + compatible = "st,st21nfcb-i2c"; + + reg = <0x08>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt new file mode 100644 index 000000000..7c89ca290 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt @@ -0,0 +1,44 @@ +* Texas Instruments TRF7970A RFID/NFC/15693 Transceiver + +Required properties: +- compatible: Should be "ti,trf7970a". +- spi-max-frequency: Maximum SPI frequency (<= 2000000). +- interrupt-parent: phandle of parent interrupt handler. +- interrupts: A single interrupt specifier. +- ti,enable-gpios: Two GPIO entries used for 'EN' and 'EN2' pins on the + TRF7970A. +- vin-supply: Regulator for supply voltage to VIN pin + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- autosuspend-delay: Specify autosuspend delay in milliseconds. +- vin-voltage-override: Specify voltage of VIN pin in microvolts. +- irq-status-read-quirk: Specify that the trf7970a being used has the + "IRQ Status Read" erratum. +- en2-rf-quirk: Specify that the trf7970a being used has the "EN2 RF" + erratum. + +Example (for ARM-based BeagleBone with TRF7970A on SPI1): + +&spi1 { + status = "okay"; + + nfc@0 { + compatible = "ti,trf7970a"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&trf7970a_default>; + spi-max-frequency = <2000000>; + interrupt-parent = <&gpio2>; + interrupts = <14 0>; + ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>, + <&gpio2 5 GPIO_ACTIVE_LOW>; + vin-supply = <&ldo3_reg>; + vin-voltage-override = <5000000>; + autosuspend-delay = <30000>; + irq-status-read-quirk; + en2-rf-quirk; + status = "okay"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/opencores-ethoc.txt b/Documentation/devicetree/bindings/net/opencores-ethoc.txt new file mode 100644 index 000000000..2dc127c30 --- /dev/null +++ b/Documentation/devicetree/bindings/net/opencores-ethoc.txt @@ -0,0 +1,22 @@ +* OpenCores MAC 10/100 Mbps + +Required properties: +- compatible: Should be "opencores,ethoc". +- reg: two memory regions (address and length), + first region is for the device registers and descriptor rings, + second is for the device packet memory. +- interrupts: interrupt for the device. + +Optional properties: +- clocks: phandle to refer to the clk used as per + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Examples: + + enet0: ethoc@fd030000 { + compatible = "opencores,ethoc"; + reg = <0xfd030000 0x4000 0xfd800000 0x4000>; + interrupts = <1>; + local-mac-address = [00 50 c2 13 6f 00]; + clocks = <&osc>; + }; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt new file mode 100644 index 000000000..40831fbaf --- /dev/null +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -0,0 +1,40 @@ +PHY nodes + +Required properties: + + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - reg : The ID number for the phy, usually a small integer + +Optional Properties: + +- compatible: Compatible list, may contain + "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for + PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45 + specifications. If neither of these are specified, the default is to + assume clause 22. The compatible list may also contain other + elements. + + If the phy's identifier is known then the list may contain an entry + of the form: "ethernet-phy-idAAAA.BBBB" where + AAAA - The value of the 16 bit Phy Identifier 1 register as + 4 hex digits. This is the chip vendor OUI bits 3:18 + BBBB - The value of the 16 bit Phy Identifier 2 register as + 4 hex digits. This is the chip vendor OUI bits 19:24, + followed by 10 bits of a vendor specific ID. + +- max-speed: Maximum PHY supported speed (10, 100, 1000...) + +Example: + +ethernet-phy@0 { + compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c22"; + interrupt-parent = <40000>; + interrupts = <35 1>; + reg = <0>; +}; diff --git a/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt new file mode 100644 index 000000000..c74989c0d --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca-qca7000-spi.txt @@ -0,0 +1,47 @@ +* Qualcomm QCA7000 (Ethernet over SPI protocol) + +Note: The QCA7000 is useable as a SPI device. In this case it must be defined +as a child of a SPI master in the device tree. + +Required properties: +- compatible : Should be "qca,qca7000" +- reg : Should specify the SPI chip select +- interrupts : The first cell should specify the index of the source interrupt + and the second cell should specify the trigger type as rising edge +- spi-cpha : Must be set +- spi-cpol: Must be set + +Optional properties: +- interrupt-parent : Specify the pHandle of the source interrupt +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at. + Numbers smaller than 1000000 or greater than 16000000 are invalid. Missing + the property will set the SPI frequency to 8000000 Hertz. +- local-mac-address: 6 bytes, MAC address +- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode. + In this mode the SPI master must toggle the chip select between each data + word. In burst mode these gaps aren't necessary, which is faster. + This setting depends on how the QCA7000 is setup via GPIO pin strapping. + If the property is missing the driver defaults to burst mode. + +Example: + +/* Freescale i.MX28 SPI master*/ +ssp2: spi@80014000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; + + qca7000: ethernet@0 { + compatible = "qca,qca7000"; + reg = <0x0>; + interrupt-parent = <&gpio3>; /* GPIO Bank 3 */ + interrupts = <25 0x1>; /* Index: 25, rising edge */ + spi-cpha; /* SPI mode: CPHA=1 */ + spi-cpol; /* SPI mode: CPOL=1 */ + spi-max-frequency = <8000000>; /* freq: 8 MHz */ + local-mac-address = [ A0 B0 C0 D0 E0 F0 ]; + }; +}; diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt new file mode 100644 index 000000000..21fd199e8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt @@ -0,0 +1,68 @@ +Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC) + +The device node has following properties. + +Required properties: + - compatible: Can be "rockchip,rk3288-gmac". + - reg: addresses and length of the register sets for the device. + - interrupts: Should contain the GMAC interrupts. + - interrupt-names: Should contain the interrupt names "macirq". + - rockchip,grf: phandle to the syscon grf used to control speed and mode. + - clocks: <&cru SCLK_MAC>: clock selector for main clock, from PLL or PHY. + <&cru SCLK_MAC_PLL>: PLL clock for SCLK_MAC + <&cru SCLK_MAC_RX>: clock gate for RX + <&cru SCLK_MAC_TX>: clock gate for TX + <&cru SCLK_MACREF>: clock gate for RMII referce clock + <&cru SCLK_MACREF_OUT> clock gate for RMII reference clock output + <&cru ACLK_GMAC>: AXI clock gate for GMAC + <&cru PCLK_GMAC>: APB clock gate for GMAC + - clock-names: One name for each entry in the clocks property. + - phy-mode: See ethernet.txt file in the same directory. + - pinctrl-names: Names corresponding to the numbered pinctrl states. + - pinctrl-0: pin-control mode. can be <&rgmii_pins> or <&rmii_pins>. + - clock_in_out: For RGMII, it must be "input", means main clock(125MHz) + is not sourced from SoC's PLL, but input from PHY; For RMII, "input" means + PHY provides the reference clock(50MHz), "output" means GMAC provides the + reference clock. + - snps,reset-gpio gpio number for phy reset. + - snps,reset-active-low boolean flag to indicate if phy reset is active low. + - assigned-clocks: main clock, should be <&cru SCLK_MAC>; + - assigned-clock-parents = parent of main clock. + can be <&ext_gmac> or <&cru SCLK_MAC_PLL>. + +Optional properties: + - tx_delay: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as default. + - rx_delay: Delay value for RXD timing. Range value is 0~0x7F, 0x10 as default. + - phy-supply: phandle to a regulator if the PHY needs one + +Example: + +gmac: ethernet@ff290000 { + compatible = "rockchip,rk3288-gmac"; + reg = <0xff290000 0x10000>; + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + rockchip,grf = <&grf>; + clocks = <&cru SCLK_MAC>, + <&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>, + <&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>, + <&cru ACLK_GMAC>, <&cru PCLK_GMAC>; + clock-names = "stmmaceth", + "mac_clk_rx", "mac_clk_tx", + "clk_mac_ref", "clk_mac_refout", + "aclk_mac", "pclk_mac"; + phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins /*&rmii_pins*/>; + + clock_in_out = "input"; + snps,reset-gpio = <&gpio4 7 0>; + snps,reset-active-low; + + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + tx_delay = <0x30>; + rx_delay = <0x10>; + + status = "ok"; +}; diff --git a/Documentation/devicetree/bindings/net/samsung-sxgbe.txt b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt new file mode 100644 index 000000000..888c25019 --- /dev/null +++ b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt @@ -0,0 +1,52 @@ +* Samsung 10G Ethernet driver (SXGBE) + +Required properties: +- compatible: Should be "samsung,sxgbe-v2.0a" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the SXGBE interrupts + These interrupts are ordered by fixed and follows variable + trasmit DMA interrupts, receive DMA interrupts and lpi interrupt. + index 0 - this is fixed common interrupt of SXGBE and it is always + available. + index 1 to 25 - 8 variable trasmit interrupts, variable 16 receive interrupts + and 1 optional lpi interrupt. +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "sgmii", "xgmii". +- samsung,pbl: Integer, Programmable Burst Length. + Supported values are 1, 2, 4, 8, 16, or 32. +- samsung,burst-map: Integer, Program the possible bursts supported by sxgbe + This is an integer and represents allowable DMA bursts when fixed burst. + Allowable range is 0x01-0x3F. When this field is set fixed burst is enabled. + When fixed length is needed for burst mode, it can be set within allowable + range. + +Optional properties: +- mac-address: 6 bytes, mac address +- max-frame-size: Maximum Transfer Unit (IEEE defined MTU), rather + than the maximum frame size. + +Example: + + aliases { + ethernet0 = <&sxgbe0>; + }; + + sxgbe0: ethernet@1a040000 { + compatible = "samsung,sxgbe-v2.0a"; + reg = <0 0x1a040000 0 0x10000>; + interrupt-parent = <&gic>; + interrupts = <0 209 4>, <0 185 4>, <0 186 4>, <0 187 4>, + <0 188 4>, <0 189 4>, <0 190 4>, <0 191 4>, + <0 192 4>, <0 193 4>, <0 194 4>, <0 195 4>, + <0 196 4>, <0 197 4>, <0 198 4>, <0 199 4>, + <0 200 4>, <0 201 4>, <0 202 4>, <0 203 4>, + <0 204 4>, <0 205 4>, <0 206 4>, <0 207 4>, + <0 208 4>, <0 210 4>; + samsung,pbl = <0x08> + samsung,burst-map = <0x20> + mac-address = [ 00 11 22 33 44 55 ]; /* Filled in by U-Boot */ + max-frame-size = <9000>; + phy-mode = "xgmii"; + }; diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt new file mode 100644 index 000000000..2f6ec85fd --- /dev/null +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -0,0 +1,57 @@ +* Renesas Electronics SH EtherMAC + +This file provides information on what the device node for the SH EtherMAC +interface contains. + +Required properties: +- compatible: "renesas,gether-r8a7740" if the device is a part of R8A7740 SoC. + "renesas,ether-r8a7778" if the device is a part of R8A7778 SoC. + "renesas,ether-r8a7779" if the device is a part of R8A7779 SoC. + "renesas,ether-r8a7790" if the device is a part of R8A7790 SoC. + "renesas,ether-r8a7791" if the device is a part of R8A7791 SoC. + "renesas,ether-r8a7793" if the device is a part of R8A7793 SoC. + "renesas,ether-r8a7794" if the device is a part of R8A7794 SoC. + "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC. +- reg: offset and length of (1) the E-DMAC/feLic register block (required), + (2) the TSU register block (optional). +- interrupts: interrupt specifier for the sole interrupt. +- phy-mode: see ethernet.txt file in the same directory. +- phy-handle: see ethernet.txt file in the same directory. +- #address-cells: number of address cells for the MDIO bus, must be equal to 1. +- #size-cells: number of size cells on the MDIO bus, must be equal to 0. +- clocks: clock phandle and specifier pair. +- pinctrl-0: phandle, referring to a default pin configuration node. + +Optional properties: +- interrupt-parent: the phandle for the interrupt controller that services + interrupts for this device. +- pinctrl-names: pin configuration state name ("default"). +- renesas,no-ether-link: boolean, specify when a board does not provide a proper + Ether LINK signal. +- renesas,ether-link-active-low: boolean, specify when the Ether LINK signal is + active-low instead of normal active-high. + +Example (Lager board): + + ethernet@ee700000 { + compatible = "renesas,ether-r8a7790"; + reg = <0 0xee700000 0 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7790_CLK_ETHER>; + phy-mode = "rmii"; + phy-handle = <&phy1>; + pinctrl-0 = <ðer_pins>; + pinctrl-names = "default"; + renesas,ether-link-active-low; + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&irqc0>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&phy1_pins>; + pinctrl-names = "default"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt new file mode 100644 index 000000000..e77e16759 --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt @@ -0,0 +1,15 @@ +SMSC LAN91c111 Ethernet mac + +Required properties: +- compatible = "smsc,lan91c111"; +- reg : physical address and size of registers +- interrupts : interrupt connection + +Optional properties: +- phy-device : see ethernet.txt file in the same directory +- reg-io-width : Mask of sizes (in bytes) of the IO accesses that + are supported on the device. Valid value for SMSC LAN91c111 are + 1, 2 or 4. If it's omitted or invalid, the size would be 2 meaning + 16-bit access only. +- power-gpios: GPIO to control the PWRDWN pin +- reset-gpios: GPIO to control the RESET pin diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt new file mode 100644 index 000000000..3fed3c124 --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc911x.txt @@ -0,0 +1,35 @@ +* Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller + +Required properties: +- compatible : Should be "smsc,lan<model>", "smsc,lan9115" +- reg : Address and length of the io space for SMSC LAN +- interrupts : Should contain SMSC LAN interrupt line +- interrupt-parent : Should be the phandle for the interrupt controller + that services interrupts for this device +- phy-mode : See ethernet.txt file in the same directory + +Optional properties: +- reg-shift : Specify the quantity to shift the register offsets by +- reg-io-width : Specify the size (in bytes) of the IO accesses that + should be performed on the device. Valid value for SMSC LAN is + 2 or 4. If it's omitted or invalid, the size would be 2. +- smsc,irq-active-high : Indicates the IRQ polarity is active-high +- smsc,irq-push-pull : Indicates the IRQ type is push-pull +- smsc,force-internal-phy : Forces SMSC LAN controller to use + internal PHY +- smsc,force-external-phy : Forces SMSC LAN controller to use + external PHY +- smsc,save-mac-address : Indicates that mac address needs to be saved + before resetting the controller + +Examples: + +lan9220@f4000000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0xf4000000 0x2000000>; + phy-mode = "mii"; + interrupt-parent = <&gpio1>; + interrupts = <31>; + reg-io-width = <4>; + smsc,irq-push-pull; +}; diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt new file mode 100644 index 000000000..3a9d67951 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -0,0 +1,31 @@ +Altera SOCFPGA SoC DWMAC controller + +This is a variant of the dwmac/stmmac driver an inherits all descriptions +present in Documentation/devicetree/bindings/net/stmmac.txt. + +The device node has additional properties: + +Required properties: + - compatible : Should contain "altr,socfpga-stmmac" along with + "snps,dwmac" and any applicable more detailed + designware version numbers documented in stmmac.txt + - altr,sysmgr-syscon : Should be the phandle to the system manager node that + encompasses the glue register, the register offset, and the register shift. + +Optional properties: +altr,emac-splitter: Should be the phandle to the emac splitter soft IP node if + DWMAC controller is connected emac splitter. + +Example: + +gmac0: ethernet@ff700000 { + compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x60 0>; + status = "disabled"; + reg = <0xff700000 0x2000>; + interrupts = <0 115 4>; + interrupt-names = "macirq"; + mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */ + clocks = <&emac_0_clk>; + clock-names = "stmmaceth"; +}; diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt new file mode 100644 index 000000000..d05c1e1fd --- /dev/null +++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt @@ -0,0 +1,61 @@ +STMicroelectronics SoC DWMAC glue layer controller + +This file documents differences between the core properties in +Documentation/devicetree/bindings/net/stmmac.txt +and what is needed on STi platforms to program the stmmac glue logic. + +The device node has following properties. + +Required properties: + - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac", + "st,stih407-dwmac", "st,stid127-dwmac". + - st,syscon : Should be phandle/offset pair. The phandle to the syscon node which + encompases the glue register, and the offset of the control register. + - st,gmac_en: this is to enable the gmac into a dedicated sysctl control + register available on STiH407 SoC. + - pinctrl-0: pin-control for all the MII mode supported. + +Optional properties: + - resets : phandle pointing to the system reset controller with correct + reset line index for ethernet reset. + - st,ext-phyclk: valid only for RMII where PHY can generate 50MHz clock or + MAC can generate it. + - st,tx-retime-src: This specifies which clk is wired up to the mac for + retimeing tx lines. This is totally board dependent and can take one of the + posssible values from "txclk", "clk_125" or "clkgen". + If not passed, the internal clock will be used by default. + - sti-ethclk: this is the phy clock. + - sti-clkconf: this is an extra sysconfig register, available in new SoCs, + to program the clk retiming. + - st,gmac_en: to enable the GMAC, this only is present in some SoCs; e.g. + STiH407. + +Example: + +ethernet0: dwmac@9630000 { + device_type = "network"; + status = "disabled"; + compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + reg = <0x9630000 0x8000>; + reg-names = "stmmaceth"; + + st,syscon = <&syscfg_sbc_reg 0x80>; + st,gmac_en; + resets = <&softreset STIH407_ETH1_SOFTRESET>; + reset-names = "stmmaceth"; + + interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>, + <GIC_SPI 99 IRQ_TYPE_NONE>, + <GIC_SPI 100 IRQ_TYPE_NONE>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; + snps,mixed-burst; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii1>; + + clock-names = "stmmaceth", "sti-ethclk"; + clocks = <&CLK_S_C0_FLEXGEN CLK_EXT2F_A9>, + <&CLK_S_C0_FLEXGEN CLK_ETH_PHY>; +}; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt new file mode 100644 index 000000000..f34fc3c81 --- /dev/null +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -0,0 +1,68 @@ +* STMicroelectronics 10/100/1000 Ethernet driver (GMAC) + +Required properties: +- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac" + For backwards compatibility: "st,spear600-gmac" is also supported. +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the STMMAC interrupts +- interrupt-names: Should contain the interrupt names "macirq" + "eth_wake_irq" if this interrupt is supported in the "interrupts" + property +- phy-mode: See ethernet.txt file in the same directory. +- snps,reset-gpio gpio number for phy reset. +- snps,reset-active-low boolean flag to indicate if phy reset is active low. +- snps,reset-delays-us is triplet of delays + The 1st cell is reset pre-delay in micro seconds. + The 2nd cell is reset pulse in micro seconds. + The 3rd cell is reset post-delay in micro seconds. +- snps,pbl Programmable Burst Length +- snps,fixed-burst Program the DMA to use the fixed burst mode +- snps,mixed-burst Program the DMA to use the mixed burst mode +- snps,force_thresh_dma_mode Force DMA to use the threshold mode for + both tx and rx +- snps,force_sf_dma_mode Force DMA to use the Store and Forward + mode for both tx and rx. This flag is + ignored if force_thresh_dma_mode is set. +- snps,multicast-filter-bins: Number of multicast filter hash bins + supported by this device instance +- snps,perfect-filter-entries: Number of perfect filter entries supported + by this device instance + +Optional properties: +- resets: Should contain a phandle to the STMMAC reset signal, if any +- reset-names: Should contain the reset signal name "stmmaceth", if a + reset phandle is given +- max-frame-size: See ethernet.txt file in the same directory +- clocks: If present, the first clock should be the GMAC main clock and + the second clock should be peripheral's register interface clock. Further + clocks may be specified in derived bindings. +- clock-names: One name for each entry in the clocks property, the + first one should be "stmmaceth" and the second one should be "pclk". +- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is + available this clock is used for programming the Timestamp Addend Register. + If not passed then the system clock will be used and this is fine on some + platforms. +- snps,burst_len: The AXI burst lenth value of the AXI BUS MODE register. +- tx-fifo-depth: See ethernet.txt file in the same directory +- rx-fifo-depth: See ethernet.txt file in the same directory + +Examples: + + gmac0: ethernet@e0800000 { + compatible = "st,spear600-gmac"; + reg = <0xe0800000 0x8000>; + interrupt-parent = <&vic1>; + interrupts = <24 23>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + max-frame-size = <3800>; + phy-mode = "gmii"; + snps,multicast-filter-bins = <256>; + snps,perfect-filter-entries = <128>; + rx-fifo-depth = <16384>; + tx-fifo-depth = <16384>; + clocks = <&clock>; + clock-names = "stmmaceth"; + }; diff --git a/Documentation/devicetree/bindings/net/via-rhine.txt b/Documentation/devicetree/bindings/net/via-rhine.txt new file mode 100644 index 000000000..334eca2bf --- /dev/null +++ b/Documentation/devicetree/bindings/net/via-rhine.txt @@ -0,0 +1,17 @@ +* VIA Rhine 10/100 Network Controller + +Required properties: +- compatible : Should be "via,vt8500-rhine" for integrated + Rhine controllers found in VIA VT8500, WonderMedia WM8950 + and similar. These are listed as 1106:3106 rev. 0x84 on the + virtual PCI bus under vendor-provided kernels +- reg : Address and length of the io space +- interrupts : Should contain the controller interrupt line + +Examples: + +ethernet@d8004000 { + compatible = "via,vt8500-rhine"; + reg = <0xd8004000 0x100>; + interrupts = <10>; +}; diff --git a/Documentation/devicetree/bindings/net/via-velocity.txt b/Documentation/devicetree/bindings/net/via-velocity.txt new file mode 100644 index 000000000..b3db469b1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/via-velocity.txt @@ -0,0 +1,20 @@ +* VIA Velocity 10/100/1000 Network Controller + +Required properties: +- compatible : Should be "via,velocity-vt6110" +- reg : Address and length of the io space +- interrupts : Should contain the controller interrupt line + +Optional properties: +- no-eeprom : PCI network cards use an external EEPROM to store data. Embedded + devices quite often set this data in uboot and do not provide an eeprom. + Specify this option if you have no external eeprom. + +Examples: + +eth0@d8004000 { + compatible = "via,velocity-vt6110"; + reg = <0xd8004000 0x400>; + interrupts = <10>; + no-eeprom; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt new file mode 100644 index 000000000..5dbf169cd --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt @@ -0,0 +1,41 @@ +Broadcom BCM43xx Fullmac wireless SDIO devices + +This node provides properties for controlling the Broadcom wireless device. The +node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + + - compatible : Should be "brcm,bcm4329-fmac". + +Optional properties: + - brcm,drive-strength : drive strength used for SDIO pins on device in mA + (default = 6). + - interrupt-parent : the phandle for the interrupt controller to which the + device interrupts are connected. + - interrupts : specifies attributes for the out-of-band interrupt (host-wake). + When not specified the device will use in-band SDIO interrupts. + - interrupt-names : name of the out-of-band interrupt, which must be set + to "host-wake". + +Example: + +mmc3: mmc@01c12000 { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins_a>; + vmmc-supply = <®_vmmc3>; + bus-width = <4>; + non-removable; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&pio>; + interrupts = <10 8>; /* PH10 / EINT10 */ + interrupt-names = "host-wake"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt new file mode 100644 index 000000000..edefc26c6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -0,0 +1,30 @@ +* Qualcomm Atheros ath10k wireless devices + +For ath10k devices the calibration data can be provided through Device +Tree. The node is a child node of the PCI controller. + +Required properties: +-compatible : Should be "qcom,ath10k" + +Optional properties: +- qcom,ath10k-calibration-data : calibration data as an array, the + length can vary between hw versions + + +Example: + +pci { + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + ath10k@0,0 { + reg = <0 0 0 0 0>; + device_type = "pci"; + qcom,ath10k-calibration-data = [ 01 02 03 ... ]; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt new file mode 100644 index 000000000..189ae5cad --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt @@ -0,0 +1,39 @@ +* Texas Instruments wl1251 wireless lan controller + +The wl1251 chip can be connected via SPI or via SDIO. This +document describes the binding for the SPI connected chip. + +Required properties: +- compatible : Should be "ti,wl1251" +- reg : Chip select address of device +- spi-max-frequency : Maximum SPI clocking speed of device in Hz +- interrupts : Should contain interrupt line +- interrupt-parent : Should be the phandle for the interrupt controller + that services interrupts for this device +- vio-supply : phandle to regulator providing VIO +- ti,power-gpio : GPIO connected to chip's PMEN pin + +Optional properties: +- ti,wl1251-has-eeprom : boolean, the wl1251 has an eeprom connected, which + provides configuration data (calibration, MAC, ...) +- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt + for optional SPI connection related properties, + +Examples: + +&spi1 { + wl1251@0 { + compatible = "ti,wl1251"; + + reg = <0>; + spi-max-frequency = <48000000>; + spi-cpol; + spi-cpha; + + interrupt-parent = <&gpio2>; + interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */ + + vio-supply = <&vio>; + ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */ + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt new file mode 100644 index 000000000..2a3d90de1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt @@ -0,0 +1,47 @@ +TI Wilink 6/7/8 (wl12xx/wl18xx) SDIO devices + +This node provides properties for controlling the wilink wireless device. The +node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + - compatible: should be one of the following: + * "ti,wl1271" + * "ti,wl1273" + * "ti,wl1281" + * "ti,wl1283" + * "ti,wl1801" + * "ti,wl1805" + * "ti,wl1807" + * "ti,wl1831" + * "ti,wl1835" + * "ti,wl1837" + - interrupts : specifies attributes for the out-of-band interrupt. + +Optional properties: + - interrupt-parent : the phandle for the interrupt controller to which the + device interrupts are connected. + - ref-clock-frequency : ref clock frequency in Hz + - tcxo-clock-frequency : tcxo clock frequency in Hz + +Note: the *-clock-frequency properties assume internal clocks. In case of external +clock, new bindings (for parsing the clock nodes) have to be added. + +Example: + +&mmc3 { + status = "okay"; + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + }; +}; |