Initial import

22 files changed, 1089 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt b/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt
new file mode 100644
index 000000000..5f3a65a9d
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt
@@ -0,0 +1,79 @@
+* APM X-Gene 15Gbps Multi-purpose PHY nodes
+
+PHY nodes are defined to describe on-chip 15Gbps Multi-purpose PHY. Each
+PHY (pair of lanes) has its own node.
+
+Required properties:
+- compatible		: Shall be "apm,xgene-phy".
+- reg			: PHY memory resource is the SDS PHY access resource.
+- #phy-cells		: Shall be 1 as it expects one argument for setting
+			  the mode of the PHY. Possible values are 0 (SATA),
+			  1 (SGMII), 2 (PCIe), 3 (USB), and 4 (XFI).
+
+Optional properties:
+- status		: Shall be "ok" if enabled or "disabled" if disabled.
+			  Default is "ok".
+- clocks		: Reference to the clock entry.
+- apm,tx-eye-tuning	: Manual control to fine tune the capture of the serial
+			  bit lines from the automatic calibrated position.
+			  Two set of 3-tuple setting for each (up to 3)
+			  supported link speed on the host. Range from 0 to
+			  127 in unit of one bit period. Default is 10.
+- apm,tx-eye-direction	: Eye tuning manual control direction. 0 means sample
+			  data earlier than the nominal sampling point. 1 means
+			  sample data later than the nominal sampling point.
+			  Two set of 3-tuple setting for each (up to 3)
+			  supported link speed on the host. Default is 0.
+- apm,tx-boost-gain	: Frequency boost AC (LSB 3-bit) and DC (2-bit)
+			  gain control. Two set of 3-tuple setting for each
+			  (up to 3) supported link speed on the host. Range is
+			  between 0 to 31 in unit of dB. Default is 3.
+- apm,tx-amplitude	: Amplitude control. Two set of 3-tuple setting for
+			  each (up to 3) supported link speed on the host.
+			  Range is between 0 to 199500 in unit of uV.
+			  Default is 199500 uV.
+- apm,tx-pre-cursor1	: 1st pre-cursor emphasis taps control. Two set of
+			  3-tuple setting for each (up to 3) supported link
+			  speed on the host. Range is 0 to 273000 in unit of
+			  uV. Default is 0.
+- apm,tx-pre-cursor2	: 2st pre-cursor emphasis taps control. Two set of
+			  3-tuple setting for each (up to 3) supported link
+			  speed on the host. Range is 0 to 127400 in unit uV.
+			  Default is 0x0.
+- apm,tx-post-cursor	: Post-cursor emphasis taps control. Two set of
+			  3-tuple setting for Gen1, Gen2, and Gen3. Range is
+			  between 0 to 0x1f in unit of 18.2mV. Default is 0xf.
+- apm,tx-speed		: Tx operating speed. One set of 3-tuple for each
+			  supported link speed on the host.
+			   0 = 1-2Gbps
+			   1 = 2-4Gbps (1st tuple default)
+			   2 = 4-8Gbps
+			   3 = 8-15Gbps (2nd tuple default)
+			   4 = 2.5-4Gbps
+			   5 = 4-5Gbps
+			   6 = 5-6Gbps
+			   7 = 6-16Gbps (3rd tuple default)
+
+NOTE: PHY override parameters are board specific setting.
+
+Example:
+		phy1: phy@1f21a000 {
+			compatible = "apm,xgene-phy";
+			reg = <0x0 0x1f21a000 0x0 0x100>;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		phy2: phy@1f22a000 {
+			compatible = "apm,xgene-phy";
+			reg = <0x0 0x1f22a000 0x0 0x100>;
+			#phy-cells = <1>;
+			status = "ok";
+		};
+
+		phy3: phy@1f23a000 {
+			compatible = "apm,xgene-phy";
+			reg = <0x0 0x1f23a000 0x0 0x100>;
+			#phy-cells = <1>;
+			status = "ok";
+		};
diff --git a/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt b/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt
new file mode 100644
index 000000000..c0155f842
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt
@@ -0,0 +1,36 @@
+Berlin SATA PHY
+---------------
+
+Required properties:
+- compatible: should be one of
+    "marvell,berlin2-sata-phy"
+    "marvell,berlin2q-sata-phy"
+- address-cells: should be 1
+- size-cells: should be 0
+- phy-cells: from the generic PHY bindings, must be 1
+- reg: address and length of the register
+- clocks: reference to the clock entry
+
+Sub-nodes:
+Each PHY should be represented as a sub-node.
+
+Sub-nodes required properties:
+- reg: the PHY number
+
+Example:
+	sata_phy: phy@f7e900a0 {
+		compatible = "marvell,berlin2q-sata-phy";
+		reg = <0xf7e900a0 0x200>;
+		clocks = <&chip CLKID_SATA>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#phy-cells = <1>;
+
+		sata-phy@0 {
+			reg = <0>;
+		};
+
+		sata-phy@1 {
+			reg = <1>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/phy/berlin-usb-phy.txt b/Documentation/devicetree/bindings/phy/berlin-usb-phy.txt
new file mode 100644
index 000000000..be33780f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/berlin-usb-phy.txt
@@ -0,0 +1,16 @@
+* Marvell Berlin USB PHY
+
+Required properties:
+- compatible: "marvell,berlin2-usb-phy" or "marvell,berlin2cd-usb-phy"
+- reg: base address and length of the registers
+- #phys-cells: should be 0
+- resets: reference to the reset controller
+
+Example:
+
+	usb-phy@f774000 {
+		compatible = "marvell,berlin2-usb-phy";
+		reg = <0xf774000 0x128>;
+		#phy-cells = <0>;
+		resets = <&chip 0x104 14>;
+	};
diff --git a/Documentation/devicetree/bindings/phy/brcm,kona-usb2-phy.txt b/Documentation/devicetree/bindings/phy/brcm,kona-usb2-phy.txt
new file mode 100644
index 000000000..3dc8b3d2f
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/brcm,kona-usb2-phy.txt
@@ -0,0 +1,15 @@
+BROADCOM KONA USB2 PHY
+
+Required properties:
+ - compatible: brcm,kona-usb2-phy
+ - reg: offset and length of the PHY registers
+ - #phy-cells: must be 0
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+Example:
+
+	usbphy: usb-phy@3f130000 {
+		compatible = "brcm,kona-usb2-phy";
+		reg = <0x3f130000 0x28>;
+		#phy-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/phy/dm816x-phy.txt b/Documentation/devicetree/bindings/phy/dm816x-phy.txt
new file mode 100644
index 000000000..2fe3d11d0
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/dm816x-phy.txt
@@ -0,0 +1,24 @@
+Device tree binding documentation for am816x USB PHY
+=========================
+
+Required properties:
+- compatible : should be "ti,dm816x-usb-phy"
+- reg : offset and length of the PHY register set.
+- reg-names : name for the phy registers
+- clocks : phandle to the clock
+- clock-names : name of the clock
+- syscon: phandle for the syscon node to access misc registers
+- #phy-cells : from the generic PHY bindings, must be 1
+- syscon: phandle for the syscon node to access misc registers
+
+Example:
+
+usb_phy0: usb-phy@20 {
+	compatible = "ti,dm8168-usb-phy";
+	reg = <0x20 0x8>;
+	reg-names = "phy";
+	clocks = <&main_fapll 6>;
+	clock-names = "refclk";
+	#phy-cells = <0>;
+	syscon = <&scm_conf>;
+};
diff --git a/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt b/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt
new file mode 100644
index 000000000..296168b74
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt
@@ -0,0 +1,22 @@
+Hisilicon hix5hd2 SATA PHY
+-----------------------
+
+Required properties:
+- compatible: should be "hisilicon,hix5hd2-sata-phy"
+- reg: offset and length of the PHY registers
+- #phy-cells: must be 0
+Refer to phy/phy-bindings.txt for the generic PHY binding properties
+
+Optional Properties:
+- hisilicon,peripheral-syscon: phandle of syscon used to control peripheral.
+- hisilicon,power-reg: offset and bit number within peripheral-syscon,
+	register of controlling sata power supply.
+
+Example:
+	sata_phy: phy@f9900000 {
+		compatible = "hisilicon,hix5hd2-sata-phy";
+		reg = <0xf9900000 0x10000>;
+		#phy-cells = <0>;
+		hisilicon,peripheral-syscon = <&peripheral_ctrl>;
+		hisilicon,power-reg = <0x8 10>;
+	};
diff --git a/Documentation/devicetree/bindings/phy/phy-bindings.txt b/Documentation/devicetree/bindings/phy/phy-bindings.txt
new file mode 100644
index 000000000..1293c3217
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-bindings.txt
@@ -0,0 +1,70 @@
+This document explains only the device tree data binding. For general
+information about PHY subsystem refer to Documentation/phy.txt
+
+PHY device node
+===============
+
+Required Properties:
+#phy-cells:	Number of cells in a PHY specifier;  The meaning of all those
+		cells is defined by the binding for the phy node. The PHY
+		provider can use the values in cells to find the appropriate
+		PHY.
+
+Optional Properties:
+phy-supply:	Phandle to a regulator that provides power to the PHY. This
+		regulator will be managed during the PHY power on/off sequence.
+
+For example:
+
+phys: phy {
+    compatible = "xxx";
+    reg = <...>;
+    .
+    .
+    #phy-cells = <1>;
+    .
+    .
+};
+
+That node describes an IP block (PHY provider) that implements 2 different PHYs.
+In order to differentiate between these 2 PHYs, an additional specifier should be
+given while trying to get a reference to it.
+
+PHY user node
+=============
+
+Required Properties:
+phys : the phandle for the PHY device (used by the PHY subsystem)
+phy-names : the names of the PHY corresponding to the PHYs present in the
+	    *phys* phandle
+
+Example 1:
+usb1: usb_otg_ss@xxx {
+    compatible = "xxx";
+    reg = <xxx>;
+    .
+    .
+    phys = <&usb2_phy>, <&usb3_phy>;
+    phy-names = "usb2phy", "usb3phy";
+    .
+    .
+};
+
+This node represents a controller that uses two PHYs, one for usb2 and one for
+usb3.
+
+Example 2:
+usb2: usb_otg_ss@xxx {
+    compatible = "xxx";
+    reg = <xxx>;
+    .
+    .
+    phys = <&phys 1>;
+    phy-names = "usbphy";
+    .
+    .
+};
+
+This node represents a controller that uses one of the PHYs of the PHY provider
+device defined previously. Note that the phy handle has an additional specifier
+"1" to differentiate between the two PHYs.
diff --git a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
new file mode 100644
index 000000000..89caa885d
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt
@@ -0,0 +1,117 @@
+STMicroelectronics STi MIPHY28LP PHY binding
+============================================
+
+This binding describes a miphy device that is used to control PHY hardware
+for SATA, PCIe or USB3.
+
+Required properties (controller (parent) node):
+- compatible	: Should be "st,miphy28lp-phy".
+- st,syscfg	: Should be a phandle of the system configuration register group
+		  which contain the SATA, PCIe or USB3 mode setting bits.
+
+Required nodes	:  A sub-node is required for each channel the controller
+		   provides. Address range information including the usual
+		   'reg' and 'reg-names' properties are used inside these
+		   nodes to describe the controller's topology. These nodes
+		   are translated by the driver's .xlate() function.
+
+Required properties (port (child) node):
+- #phy-cells	: Should be 1 (See second example)
+		  Cell after port phandle is device type from:
+			- PHY_TYPE_SATA
+			- PHY_TYPE_PCI
+			- PHY_TYPE_USB3
+- reg		: Address and length of the register set for the device.
+- reg-names	: The names of the register addresses corresponding to the registers
+		  filled in "reg". It can also contain the offset of the system configuration
+		  registers used as glue-logic to setup the device for SATA/PCIe or USB3
+		  devices.
+- st,syscfg	: Offset of the parent configuration register.
+- resets	: phandle to the parent reset controller.
+- reset-names	: Associated name must be "miphy-sw-rst".
+
+Optional properties (port (child) node):
+- st,osc-rdy		: to check the MIPHY0_OSC_RDY status in the glue-logic. This
+			  is not available in all the MiPHY. For example, for STiH407, only the
+			  MiPHY0 has this bit.
+- st,osc-force-ext	: to select the external oscillator. This can change from
+			  different MiPHY inside the same SoC.
+- st,sata_gen		: to select which SATA_SPDMODE has to be set in the SATA system config
+			  register.
+- st,px_rx_pol_inv	: to invert polarity of RXn/RXp (respectively negative line and positive
+			  line).
+- st,scc-on		: enable ssc to reduce effects of EMI (only for sata or PCIe).
+- st,tx-impedance-comp	: to compensate tx impedance avoiding out of range values.
+
+example:
+
+		miphy28lp_phy: miphy28lp@9b22000 {
+			compatible = "st,miphy28lp-phy";
+			st,syscfg = <&syscfg_core>;
+			#address-cells	= <1>;
+			#size-cells	= <1>;
+			ranges;
+
+			phy_port0: port@9b22000 {
+				reg = <0x9b22000 0xff>,
+				      <0x9b09000 0xff>,
+				      <0x9b04000 0xff>;
+				reg-names = "sata-up",
+					    "pcie-up",
+					    "pipew";
+
+				st,syscfg = <0x114 0x818 0xe0 0xec>;
+				#phy-cells = <1>;
+				st,osc-rdy;
+				reset-names = "miphy-sw-rst";
+				resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
+			};
+
+			phy_port1: port@9b2a000 {
+				reg = <0x9b2a000 0xff>,
+				      <0x9b19000 0xff>,
+				      <0x9b14000 0xff>;
+				reg-names = "sata-up",
+					    "pcie-up",
+					    "pipew";
+
+				st,syscfg = <0x118 0x81c 0xe4 0xf0>;
+
+				#phy-cells = <1>;
+				st,osc-force-ext;
+				reset-names = "miphy-sw-rst";
+				resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
+			};
+
+			phy_port2: port@8f95000 {
+				reg = <0x8f95000 0xff>,
+				      <0x8f90000 0xff>;
+				reg-names = "pipew",
+					    "usb3-up";
+
+				st,syscfg = <0x11c 0x820>;
+
+				#phy-cells = <1>;
+				reset-names = "miphy-sw-rst";
+				resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
+			};
+		};
+
+
+Specifying phy control of devices
+=================================
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the miphy device node and an index
+specifying which configuration to use, as described in phy-bindings.txt.
+
+example:
+		sata0: sata@9b20000  {
+			...
+			phys		= <&phy_port0 PHY_TYPE_SATA>;
+			...
+		};
+
+Macro definitions for the supported miphy configuration can be found in:
+
+include/dt-bindings/phy/phy.h
diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
new file mode 100644
index 000000000..8772900e0
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
@@ -0,0 +1,77 @@
+STMicroelectronics STi MIPHY365x PHY binding
+============================================
+
+This binding describes a miphy device that is used to control PHY hardware
+for SATA and PCIe.
+
+Required properties (controller (parent) node):
+- compatible    : Should be "st,miphy365x-phy"
+- st,syscfg     : Phandle / integer array property. Phandle of sysconfig group
+		  containing the miphy registers and integer array should contain
+		  an entry for each port sub-node, specifying the control
+		  register offset inside the sysconfig group.
+
+Required nodes	:  A sub-node is required for each channel the controller
+		   provides. Address range information including the usual
+		   'reg' and 'reg-names' properties are used inside these
+		   nodes to describe the controller's topology. These nodes
+		   are translated by the driver's .xlate() function.
+
+Required properties (port (child) node):
+- #phy-cells 	: Should be 1 (See second example)
+		  Cell after port phandle is device type from:
+			- PHY_TYPE_SATA
+			- PHY_TYPE_PCI
+- reg        	: Address and length of register sets for each device in
+		  "reg-names"
+- reg-names     : The names of the register addresses corresponding to the
+		  registers filled in "reg":
+			- sata:   For SATA devices
+			- pcie:   For PCIe devices
+
+Optional properties (port (child) node):
+- st,sata-gen	     :	Generation of locally attached SATA IP. Expected values
+			are {1,2,3). If not supplied generation 1 hardware will
+			be expected
+- st,pcie-tx-pol-inv :	Bool property to invert the polarity PCIe Tx (Txn/Txp)
+- st,sata-tx-pol-inv :	Bool property to invert the polarity SATA Tx (Txn/Txp)
+
+Example:
+
+	miphy365x_phy: miphy365x@fe382000 {
+		compatible      = "st,miphy365x-phy";
+		st,syscfg  	= <&syscfg_rear 0x824 0x828>;
+		#address-cells	= <1>;
+		#size-cells	= <1>;
+		ranges;
+
+		phy_port0: port@fe382000 {
+			reg = <0xfe382000 0x100>, <0xfe394000 0x100>;
+			reg-names = "sata", "pcie";
+			#phy-cells = <1>;
+			st,sata-gen = <3>;
+		};
+
+		phy_port1: port@fe38a000 {
+			reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;;
+			reg-names = "sata", "pcie", "syscfg";
+			#phy-cells = <1>;
+			st,pcie-tx-pol-inv;
+		};
+	};
+
+Specifying phy control of devices
+=================================
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+	sata0: sata@fe380000 {
+		...
+		phys	  = <&phy_port0 PHY_TYPE_SATA>;
+		...
+	};
diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu.txt b/Documentation/devicetree/bindings/phy/phy-mvebu.txt
new file mode 100644
index 000000000..f95b6260a
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-mvebu.txt
@@ -0,0 +1,43 @@
+* Marvell MVEBU SATA PHY
+
+Power control for the SATA phy found on Marvell MVEBU SoCs.
+
+This document extends the binding described in phy-bindings.txt
+
+Required properties :
+
+ - reg		   : Offset and length of the register set for the SATA device
+ - compatible	   : Should be "marvell,mvebu-sata-phy"
+ - clocks	   : phandle of clock and specifier that supplies the device
+ - clock-names	   : Should be "sata"
+
+Example:
+		sata-phy@84000 {
+			compatible = "marvell,mvebu-sata-phy";
+			reg = <0x84000 0x0334>;
+			clocks = <&gate_clk 15>;
+			clock-names = "sata";
+			#phy-cells = <0>;
+			status = "ok";
+		};
+
+Armada 375 USB cluster
+----------------------
+
+Armada 375 comes with an USB2 host and device controller and an USB3
+controller. The USB cluster control register allows to manage common
+features of both USB controllers.
+
+Required properties:
+
+- compatible: "marvell,armada-375-usb-cluster"
+- reg: Should contain usb cluster register location and length.
+- #phy-cells : from the generic phy bindings, must be 1. Possible
+values are 1 (USB2), 2 (USB3).
+
+Example:
+		usbcluster: usb-cluster@18400 {
+			compatible = "marvell,armada-375-usb-cluster";
+			reg = <0x18400 0x4>;
+			#phy-cells = <1>
+		};
diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
new file mode 100644
index 000000000..de6a706ab
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
@@ -0,0 +1,24 @@
+ST STiH407 USB PHY controller
+
+This file documents the dt bindings for the usb picoPHY driver which is the PHY for both USB2 and USB3
+host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC family from STMicroelectronics.
+
+Required properties:
+- compatible		: should be "st,stih407-usb2-phy"
+- st,syscfg		: phandle of sysconfig bank plus integer array containing phyparam and phyctrl register offsets
+- resets		: list of phandle and reset specifier pairs. There should be two entries, one
+			  for the whole phy and one for the port
+- reset-names		: list of reset signal names. Should be "global" and "port"
+See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+Example:
+
+usb2_picophy0: usbpicophy@f8 {
+	compatible	= "st,stih407-usb2-phy";
+	#phy-cells	= <0>;
+	st,syscfg	= <&syscfg_core 0x100 0xf4>;
+	resets		= <&softreset STIH407_PICOPHY_SOFTRESET>,
+			  <&picophyreset STIH407_PICOPHY0_RESET>;
+	reset-names	= "global", "port";
+};
diff --git a/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt
new file mode 100644
index 000000000..00944a05e
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-stih41x-usb.txt
@@ -0,0 +1,24 @@
+STMicroelectronics STiH41x USB PHY binding
+------------------------------------------
+
+This file contains documentation for the usb phy found in STiH415/6 SoCs from
+STMicroelectronics.
+
+Required properties:
+- compatible	: should be "st,stih416-usb-phy" or "st,stih415-usb-phy"
+- st,syscfg	: should be a phandle of the syscfg node
+- clock-names	: must contain "osc_phy"
+- clocks	: must contain an entry for each name in clock-names.
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+- #phy-cells	: must be 0 for this phy
+See: Documentation/devicetree/bindings/phy/phy-bindings.txt
+
+Example:
+
+usb2_phy: usb2phy@0 {
+	compatible	= "st,stih416-usb-phy";
+	#phy-cell	= <0>;
+	st,syscfg	= <&syscfg_rear>;
+	clocks		= <&clk_sysin>;
+	clock-names	= "osc_phy";
+};
diff --git a/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt b/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt
new file mode 100644
index 000000000..952f6c96b
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt
@@ -0,0 +1,24 @@
+Qualcomm APQ8064 SATA PHY Controller
+------------------------------------
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible: compatible list, contains "qcom,apq8064-sata-phy".
+- reg: offset and length of the SATA PHY register set;
+- #phy-cells: must be zero
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+- clock-names: must be "cfg" for phy config clock.
+
+Example:
+	sata_phy: sata-phy@1b400000 {
+		compatible = "qcom,apq8064-sata-phy";
+		reg = <0x1b400000 0x200>;
+
+		clocks = <&gcc SATA_PHY_CFG_CLK>;
+		clock-names = "cfg";
+
+		#phy-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
new file mode 100644
index 000000000..86f2dbe07
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
@@ -0,0 +1,39 @@
+Qualcomm DWC3 HS AND SS PHY CONTROLLER
+--------------------------------------
+
+DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer
+controllers.  Each DWC3 PHY controller should have its own node.
+
+Required properties:
+- compatible: should contain one of the following:
+	- "qcom,dwc3-hs-usb-phy" for High Speed Synopsis PHY controller
+	- "qcom,dwc3-ss-usb-phy" for Super Speed Synopsis PHY controller
+- reg: offset and length of the DWC3 PHY controller register set
+- #phy-cells: must be zero
+- clocks: a list of phandles and clock-specifier pairs, one for each entry in
+  clock-names.
+- clock-names: Should contain "ref" for the PHY reference clock
+
+Optional clocks:
+  "xo"		External reference clock
+
+Example:
+		phy@100f8800 {
+			compatible = "qcom,dwc3-hs-usb-phy";
+			reg = <0x100f8800 0x30>;
+			clocks = <&gcc USB30_0_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "ok";
+		};
+
+		phy@100f8830 {
+			compatible = "qcom,dwc3-ss-usb-phy";
+			reg = <0x100f8830 0x30>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "ok";
+		};
diff --git a/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt b/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt
new file mode 100644
index 000000000..76bfbd056
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt
@@ -0,0 +1,23 @@
+Qualcomm IPQ806x SATA PHY Controller
+------------------------------------
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible: compatible list, contains "qcom,ipq806x-sata-phy"
+- reg: offset and length of the SATA PHY register set;
+- #phy-cells: must be zero
+- clocks: must be exactly one entry
+- clock-names: must be "cfg"
+
+Example:
+	sata_phy: sata-phy@1b400000 {
+		compatible = "qcom,ipq806x-sata-phy";
+		reg = <0x1b400000 0x200>;
+
+		clocks = <&gcc SATA_PHY_CFG_CLK>;
+		clock-names = "cfg";
+
+		#phy-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt
new file mode 100644
index 000000000..00fc52a03
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt
@@ -0,0 +1,51 @@
+* Renesas R-Car generation 2 USB PHY
+
+This file provides information on what the device node for the R-Car generation
+2 USB PHY contains.
+
+Required properties:
+- compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC.
+	      "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC.
+- reg: offset and length of the register block.
+- #address-cells: number of address cells for the USB channel subnodes, must
+		  be <1>.
+- #size-cells: number of size cells for the USB channel subnodes, must be <0>.
+- clocks: clock phandle and specifier pair.
+- clock-names: string, clock input name, must be "usbhs".
+
+The USB PHY device tree node should have the subnodes corresponding to the USB
+channels. These subnodes must contain the following properties:
+- reg: the USB controller selector; see the table below for the values.
+- #phy-cells: see phy-bindings.txt in the same directory, must be <1>.
+
+The phandle's argument in the PHY specifier is the USB controller selector for
+the USB channel; see the selector meanings below:
+
++-----------+---------------+---------------+
+|\ Selector |               |               |
++ --------- +       0       |       1       |
+| Channel  \|               |               |
++-----------+---------------+---------------+
+| 0         | PCI EHCI/OHCI | HS-USB        |
+| 2         | PCI EHCI/OHCI | xHCI          |
++-----------+---------------+---------------+
+
+Example (Lager board):
+
+	usb-phy@e6590100 {
+		compatible = "renesas,usb-phy-r8a7790";
+		reg = <0 0xe6590100 0 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&mstp7_clks R8A7790_CLK_HSUSB>;
+		clock-names = "usbhs";
+
+		usb-channel@0 {
+			reg = <0>;
+			#phy-cells = <1>;
+		};
+		usb-channel@2 {
+			reg = <2>;
+			#phy-cells = <1>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt
new file mode 100644
index 000000000..826454ac4
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.txt
@@ -0,0 +1,37 @@
+ROCKCHIP USB2 PHY
+
+Required properties:
+ - compatible: rockchip,rk3288-usb-phy
+ - rockchip,grf : phandle to the syscon managing the "general
+   register files"
+ - #address-cells: should be 1
+ - #size-cells: should be 0
+
+Sub-nodes:
+Each PHY should be represented as a sub-node.
+
+Sub-nodes
+required properties:
+- #phy-cells: should be 0
+- reg: PHY configure reg address offset in GRF
+		"0x320" - for PHY attach to OTG controller
+		"0x334" - for PHY attach to HOST0 controller
+		"0x348" - for PHY attach to HOST1 controller
+
+Optional Properties:
+- clocks : phandle + clock specifier for the phy clocks
+- clock-names: string, clock name, must be "phyclk"
+
+Example:
+
+usbphy: phy {
+	compatible = "rockchip,rk3288-usb-phy";
+	rockchip,grf = <&grf>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	usbphy0: usb-phy0 {
+		#phy-cells = <0>;
+		reg = <0x320>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
new file mode 100644
index 000000000..60c6f2a63
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
@@ -0,0 +1,176 @@
+Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY
+-------------------------------------------------
+
+Required properties:
+- compatible : should be "samsung,s5pv210-mipi-video-phy";
+- #phy-cells : from the generic phy bindings, must be 1;
+- syscon - phandle to the PMU system controller;
+
+For "samsung,s5pv210-mipi-video-phy" compatible PHYs the second cell in
+the PHY specifier identifies the PHY and its meaning is as follows:
+  0 - MIPI CSIS 0,
+  1 - MIPI DSIM 0,
+  2 - MIPI CSIS 1,
+  3 - MIPI DSIM 1.
+
+Samsung EXYNOS SoC series Display Port PHY
+-------------------------------------------------
+
+Required properties:
+- compatible : should be one of the following supported values:
+	 - "samsung,exynos5250-dp-video-phy"
+	 - "samsung,exynos5420-dp-video-phy"
+- samsung,pmu-syscon: phandle for PMU system controller interface, used to
+		      control pmu registers for power isolation.
+- #phy-cells : from the generic PHY bindings, must be 0;
+
+Samsung S5P/EXYNOS SoC series USB PHY
+-------------------------------------------------
+
+Required properties:
+- compatible : should be one of the listed compatibles:
+	- "samsung,exynos3250-usb2-phy"
+	- "samsung,exynos4210-usb2-phy"
+	- "samsung,exynos4x12-usb2-phy"
+	- "samsung,exynos5250-usb2-phy"
+	- "samsung,s5pv210-usb2-phy"
+- reg : a list of registers used by phy driver
+	- first and obligatory is the location of phy modules registers
+- samsung,sysreg-phandle - handle to syscon used to control the system registers
+- samsung,pmureg-phandle - handle to syscon used to control PMU registers
+- #phy-cells : from the generic phy bindings, must be 1;
+- clocks and clock-names:
+	- the "phy" clock is required by the phy module, used as a gate
+	- the "ref" clock is used to get the rate of the clock provided to the
+	  PHY module
+
+The first phandle argument in the PHY specifier identifies the PHY, its
+meaning is compatible dependent. For the currently supported SoCs (Exynos 4210
+and Exynos 4212) it is as follows:
+  0 - USB device ("device"),
+  1 - USB host ("host"),
+  2 - HSIC0 ("hsic0"),
+  3 - HSIC1 ("hsic1"),
+Exynos3250 has only USB device phy available as phy 0.
+
+Exynos 4210 and Exynos 4212 use mode switching and require that mode switch
+register is supplied.
+
+Example:
+
+For Exynos 4412 (compatible with Exynos 4212):
+
+usbphy: phy@125b0000 {
+	compatible = "samsung,exynos4x12-usb2-phy";
+	reg = <0x125b0000 0x100>;
+	clocks = <&clock 305>, <&clock 2>;
+	clock-names = "phy", "ref";
+	status = "okay";
+	#phy-cells = <1>;
+	samsung,sysreg-phandle = <&sys_reg>;
+	samsung,pmureg-phandle = <&pmu_reg>;
+};
+
+Then the PHY can be used in other nodes such as:
+
+phy-consumer@12340000 {
+	phys = <&usbphy 2>;
+	phy-names = "phy";
+};
+
+Refer to DT bindings documentation of particular PHY consumer devices for more
+information about required PHYs and the way of specification.
+
+Samsung SATA PHY Controller
+---------------------------
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5250-sata-phy"
+- reg : offset and length of the SATA PHY register set;
+- #phy-cells : must be zero
+- clocks : must be exactly one entry
+- clock-names : must be "sata_phyctrl"
+- samsung,exynos-sataphy-i2c-phandle : a phandle to the I2C device, no arguments
+- samsung,syscon-phandle : a phandle to the PMU system controller, no arguments
+
+Example:
+	sata_phy: sata-phy@12170000 {
+		compatible = "samsung,exynos5250-sata-phy";
+		reg = <0x12170000 0x1ff>;
+		clocks = <&clock 287>;
+		clock-names = "sata_phyctrl";
+		#phy-cells = <0>;
+		samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
+		samsung,syscon-phandle = <&pmu_syscon>;
+	};
+
+Device-Tree bindings for sataphy i2c client driver
+--------------------------------------------------
+
+Required properties:
+compatible: Should be "samsung,exynos-sataphy-i2c"
+- reg: I2C address of the sataphy i2c device.
+
+Example:
+
+	sata_phy_i2c:sata-phy@38 {
+		compatible = "samsung,exynos-sataphy-i2c";
+		reg = <0x38>;
+	};
+
+Samsung Exynos5 SoC series USB DRD PHY controller
+--------------------------------------------------
+
+Required properties:
+- compatible : Should be set to one of the following supported values:
+	- "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC,
+	- "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC.
+	- "samsung,exynos5433-usbdrd-phy" - for exynos5433 SoC.
+	- "samsung,exynos7-usbdrd-phy" - for exynos7 SoC.
+- reg : Register offset and length of USB DRD PHY register set;
+- clocks: Clock IDs array as required by the controller
+- clock-names: names of clocks correseponding to IDs in the clock property;
+	       Required clocks:
+	- phy: main PHY clock (same as USB DRD controller i.e. DWC3 IP clock),
+	       used for register access.
+	- ref: PHY's reference clock (usually crystal clock), used for
+	       PHY operations, associated by phy name. It is used to
+	       determine bit values for clock settings register.
+	       For Exynos5420 this is given as 'sclk_usbphy30' in CMU.
+	- optional clocks: Exynos5433 & Exynos7 SoC has now following additional
+			   gate clocks available:
+			   - phy_pipe: for PIPE3 phy
+			   - phy_utmi: for UTMI+ phy
+			   - itp: for ITP generation
+- samsung,pmu-syscon: phandle for PMU system controller interface, used to
+		      control pmu registers for power isolation.
+- #phy-cells : from the generic PHY bindings, must be 1;
+
+For "samsung,exynos5250-usbdrd-phy" and "samsung,exynos5420-usbdrd-phy"
+compatible PHYs, the second cell in the PHY specifier identifies the
+PHY id, which is interpreted as follows:
+  0 - UTMI+ type phy,
+  1 - PIPE3 type phy,
+
+Example:
+	usbdrd_phy: usbphy@12100000 {
+		compatible = "samsung,exynos5250-usbdrd-phy";
+		reg = <0x12100000 0x100>;
+		clocks = <&clock 286>, <&clock 1>;
+		clock-names = "phy", "ref";
+		samsung,pmu-syscon = <&pmu_system_controller>;
+		#phy-cells = <1>;
+	};
+
+- aliases: For SoCs like Exynos5420 having multiple USB 3.0 DRD PHY controllers,
+	   'usbdrd_phy' nodes should have numbered alias in the aliases node,
+	   in the form of usbdrdphyN, N = 0, 1... (depending on number of
+	   controllers).
+Example:
+	aliases {
+		usbdrdphy0 = &usb3_phy0;
+		usbdrdphy1 = &usb3_phy1;
+	};
diff --git a/Documentation/devicetree/bindings/phy/st-spear-miphy.txt b/Documentation/devicetree/bindings/phy/st-spear-miphy.txt
new file mode 100644
index 000000000..2a6bfdcc0
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/st-spear-miphy.txt
@@ -0,0 +1,15 @@
+ST SPEAr miphy DT details
+=========================
+
+ST Microelectronics SPEAr miphy is a phy controller supporting PCIe and SATA.
+
+Required properties:
+- compatible : should be "st,spear1310-miphy" or "st,spear1340-miphy"
+- reg : offset and length of the PHY register set.
+- misc: phandle for the syscon node to access misc registers
+- #phy-cells : from the generic PHY bindings, must be 1.
+	- cell[1]: 0 if phy used for SATA, 1 for PCIe.
+
+Optional properties:
+- phy-id: Instance id of the phy. Only required when there are multiple phys
+  present on a implementation.
diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
new file mode 100644
index 000000000..16528b9eb
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
@@ -0,0 +1,37 @@
+Allwinner sun4i USB PHY
+-----------------------
+
+Required properties:
+- compatible : should be one of
+  * allwinner,sun4i-a10-usb-phy
+  * allwinner,sun5i-a13-usb-phy
+  * allwinner,sun6i-a31-usb-phy
+  * allwinner,sun7i-a20-usb-phy
+- reg : a list of offset + length pairs
+- reg-names :
+  * "phy_ctrl"
+  * "pmu1"
+  * "pmu2" for sun4i, sun6i or sun7i
+- #phy-cells : from the generic phy bindings, must be 1
+- clocks : phandle + clock specifier for the phy clocks
+- clock-names :
+  * "usb_phy" for sun4i, sun5i or sun7i
+  * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i
+- resets : a list of phandle + reset specifier pairs
+- reset-names :
+  * "usb0_reset"
+  * "usb1_reset"
+  * "usb2_reset" for sun4i, sun6i or sun7i
+
+Example:
+	usbphy: phy@0x01c13400 {
+		#phy-cells = <1>;
+		compatible = "allwinner,sun4i-a10-usb-phy";
+		/* phy base regs, phy1 pmu reg, phy2 pmu reg */
+		reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>;
+		reg-names = "phy_ctrl", "pmu1", "pmu2";
+		clocks = <&usb_clk 8>;
+		clock-names = "usb_phy";
+		resets = <&usb_clk 1>, <&usb_clk 2>;
+		reset-names = "usb1_reset", "usb2_reset";
+	};
diff --git a/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt
new file mode 100644
index 000000000..1cca85c70
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt
@@ -0,0 +1,38 @@
+Allwinner sun9i USB PHY
+-----------------------
+
+Required properties:
+- compatible : should be one of
+  * allwinner,sun9i-a80-usb-phy
+- reg : a list of offset + length pairs
+- #phy-cells : from the generic phy bindings, must be 0
+- phy_type : "hsic" for HSIC usage;
+	     other values or absence of this property indicates normal USB
+- clocks : phandle + clock specifier for the phy clocks
+- clock-names : depending on the "phy_type" property,
+  * "phy" for normal USB
+  * "hsic_480M", "hsic_12M" for HSIC
+- resets : a list of phandle + reset specifier pairs
+- reset-names : depending on the "phy_type" property,
+  * "phy" for normal USB
+  * "hsic" for HSIC
+
+Optional Properties:
+- phy-supply : from the generic phy bindings, a phandle to a regulator that
+	       provides power to VBUS.
+
+It is recommended to list all clocks and resets available.
+The driver will only use those matching the phy_type.
+
+Example:
+	usbphy1: phy@00a01800 {
+		compatible = "allwinner,sun9i-a80-usb-phy";
+		reg = <0x00a01800 0x4>;
+		clocks = <&usb_phy_clk 2>, <&usb_phy_clk 10>,
+		       <&usb_phy_clk 3>;
+		clock-names = "hsic_480M", "hsic_12M", "phy";
+		resets = <&usb_phy_clk 18>, <&usb_phy_clk 19>;
+		reset-names = "hsic", "phy";
+		status = "disabled";
+		#phy-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt
new file mode 100644
index 000000000..305e3df3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/ti-phy.txt
@@ -0,0 +1,102 @@
+TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
+
+OMAP CONTROL PHY
+
+Required properties:
+ - compatible: Should be one of
+ "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
+ "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
+                        e.g. USB2_PHY on OMAP5.
+ "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
+                        e.g. USB3 PHY and SATA PHY on OMAP5.
+ "ti,control-phy-pcie" - for pcie to support external clock for pcie and to
+			set PCS delay value.
+			e.g. PCIE PHY in DRA7x
+ "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on
+                        DRA7 platform.
+ "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on
+                        AM437 platform.
+ - reg : register ranges as listed in the reg-names property
+ - reg-names: "otghs_control" for control-phy-otghs
+	      "power", "pcie_pcs" and "control_sma" for control-phy-pcie
+	      "power" for all other types
+
+omap_control_usb: omap-control-usb@4a002300 {
+        compatible = "ti,control-phy-otghs";
+        reg = <0x4a00233c 0x4>;
+        reg-names = "otghs_control";
+};
+
+OMAP USB2 PHY
+
+Required properties:
+ - compatible: Should be "ti,omap-usb2"
+ - reg : Address and length of the register set for the device.
+ - #phy-cells: determine the number of cells that should be given in the
+   phandle while referencing this phy.
+ - clocks: a list of phandles and clock-specifier pairs, one for each entry in
+   clock-names.
+ - clock-names: should include:
+   * "wkupclk" - wakeup clock.
+   * "refclk" - reference clock (optional).
+
+Optional properties:
+ - ctrl-module : phandle of the control module used by PHY driver to power on
+   the PHY.
+
+This is usually a subnode of ocp2scp to which it is connected.
+
+usb2phy@4a0ad080 {
+	compatible = "ti,omap-usb2";
+	reg = <0x4a0ad080 0x58>;
+	ctrl-module = <&omap_control_usb>;
+	#phy-cells = <0>;
+	clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
+	clock-names = "wkupclk", "refclk";
+};
+
+TI PIPE3 PHY
+
+Required properties:
+ - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or
+   "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated.
+ - reg : Address and length of the register set for the device.
+ - reg-names: The names of the register addresses corresponding to the registers
+   filled in "reg".
+ - #phy-cells: determine the number of cells that should be given in the
+   phandle while referencing this phy.
+ - clocks: a list of phandles and clock-specifier pairs, one for each entry in
+   clock-names.
+ - clock-names: should include:
+   * "wkupclk" - wakeup clock.
+   * "sysclk" - system clock.
+   * "refclk" - reference clock.
+   * "dpll_ref" - external dpll ref clk
+   * "dpll_ref_m2" - external dpll ref clk
+   * "phy-div" - divider for apll
+   * "div-clk" - apll clock
+
+Optional properties:
+ - ctrl-module : phandle of the control module used by PHY driver to power on
+   the PHY.
+ - id: If there are multiple instance of the same type, in order to
+   differentiate between each instance "id" can be used (e.g., multi-lane PCIe
+   PHY). If "id" is not provided, it is set to default value of '1'.
+
+This is usually a subnode of ocp2scp to which it is connected.
+
+usb3phy@4a084400 {
+	compatible = "ti,phy-usb3";
+	reg = <0x4a084400 0x80>,
+	      <0x4a084800 0x64>,
+	      <0x4a084c00 0x40>;
+	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
+	ctrl-module = <&omap_control_usb>;
+	#phy-cells = <0>;
+	clocks = <&usb_phy_cm_clk32k>,
+		 <&sys_clkin>,
+		 <&usb_otg_ss_refclk960m>;
+	clock-names =	"wkupclk",
+			"sysclk",
+			"refclk";
+};