Initial import

62 files changed, 7831 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/abilis,tb10x-iomux.txt b/Documentation/devicetree/bindings/pinctrl/abilis,tb10x-iomux.txt
new file mode 100644
index 000000000..2c1186622
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/abilis,tb10x-iomux.txt
@@ -0,0 +1,80 @@
+Abilis Systems TB10x pin controller
+===================================
+
+Required properties
+-------------------
+
+- compatible: should be "abilis,tb10x-iomux";
+- reg: should contain the physical address and size of the pin controller's
+  register range.
+
+
+Function definitions
+--------------------
+
+Functions are defined (and referenced) by sub-nodes of the pin controller.
+Every sub-node defines exactly one function (implying a set of pins).
+Every function is associated to one named pin group inside the pin controller
+driver and these names are used to associate pin group predefinitions to pin
+controller sub-nodes.
+
+Required function definition subnode properties:
+  - abilis,function: should be set to the name of the function's pin group.
+
+The following pin groups are available:
+  - GPIO ports: gpioa, gpiob, gpioc, gpiod, gpioe, gpiof, gpiog,
+                gpioh, gpioi, gpioj, gpiok, gpiol, gpiom, gpion
+  - Serial TS input ports: mis0, mis1, mis2, mis3, mis4, mis5, mis6, mis7
+  - Parallel TS input ports: mip1, mip3, mip5, mip7
+  - Serial TS output ports: mos0, mos1, mos2, mos3
+  - Parallel TS output port: mop
+  - CI+ port: ciplus
+  - CableCard (Mcard) port: mcard
+  - Smart card ports: stc0, stc1
+  - UART ports: uart0, uart1
+  - SPI ports: spi1, spi3
+  - JTAG: jtag
+
+All other ports of the chip are not multiplexed and thus not managed by this
+driver.
+
+
+GPIO ranges definition
+----------------------
+
+The named pin groups of GPIO ports can be used to define GPIO ranges as
+explained in Documentation/devicetree/bindings/gpio/gpio.txt.
+
+
+Example
+-------
+
+iomux: iomux@FF10601c {
+	compatible = "abilis,tb10x-iomux";
+	reg = <0xFF10601c 0x4>;
+	pctl_gpio_a: pctl-gpio-a {
+		abilis,function = "gpioa";
+	};
+	pctl_uart0: pctl-uart0 {
+		abilis,function = "uart0";
+	};
+};
+uart@FF100000 {
+	compatible = "snps,dw-apb-uart";
+	reg = <0xFF100000 0x100>;
+	clock-frequency = <166666666>;
+	interrupts = <25 1>;
+	reg-shift = <2>;
+	reg-io-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pctl_uart0>;
+};
+gpioa: gpio@FF140000 {
+	compatible = "abilis,tb10x-gpio";
+	reg = <0xFF140000 0x1000>;
+	gpio-controller;
+	#gpio-cells = <2>;
+	ngpio = <3>;
+	gpio-ranges = <&iomux 0 0>;
+	gpio-ranges-group-names = "gpioa";
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
new file mode 100644
index 000000000..fdd8046e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt
@@ -0,0 +1,68 @@
+* Allwinner A1X Pin Controller
+
+The pins controlled by sunXi pin controller are organized in banks,
+each bank has 32 pins.  Each pin has 7 multiplexing functions, with
+the first two functions being GPIO in and out. The configuration on
+the pins includes drive strength and pull-up.
+
+Required properties:
+- compatible: Should be one of the followings (depending on you SoC):
+  "allwinner,sun4i-a10-pinctrl"
+  "allwinner,sun5i-a10s-pinctrl"
+  "allwinner,sun5i-a13-pinctrl"
+  "allwinner,sun6i-a31-pinctrl"
+  "allwinner,sun6i-a31s-pinctrl"
+  "allwinner,sun6i-a31-r-pinctrl"
+  "allwinner,sun7i-a20-pinctrl"
+  "allwinner,sun8i-a23-pinctrl"
+  "allwinner,sun8i-a23-r-pinctrl"
+- reg: Should contain the register physical address and length for the
+  pin controller.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices.
+
+A pinctrl node should contain at least one subnodes representing the
+pinctrl groups available on the machine. Each subnode will list the
+pins it needs, and how they should be configured, with regard to muxer
+configuration, drive strength and pullups. If one of these options is
+not set, its actual value will be unspecified.
+
+Required subnode-properties:
+
+- allwinner,pins: List of strings containing the pin name.
+- allwinner,function: Function to mux the pins listed above to.
+
+Optional subnode-properties:
+- allwinner,drive: Integer. Represents the current sent to the pin
+    0: 10 mA
+    1: 20 mA
+    2: 30 mA
+    3: 40 mA
+- allwinner,pull: Integer.
+    0: No resistor
+    1: Pull-up resistor
+    2: Pull-down resistor
+
+Examples:
+
+pinctrl@01c20800 {
+	compatible = "allwinner,sun5i-a13-pinctrl";
+	reg = <0x01c20800 0x400>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	uart1_pins_a: uart1@0 {
+		allwinner,pins = "PE10", "PE11";
+		allwinner,function = "uart1";
+		allwinner,drive = <0>;
+		allwinner,pull = <0>;
+	};
+
+	uart1_pins_b: uart1@1 {
+		allwinner,pins = "PG3", "PG4";
+		allwinner,function = "uart1";
+		allwinner,drive = <0>;
+		allwinner,pull = <0>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
new file mode 100644
index 000000000..b7a93e80a
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
@@ -0,0 +1,150 @@
+* Atmel AT91 Pinmux Controller
+
+The AT91 Pinmux Controller, enables the IC
+to share one PAD to several functional blocks. The sharing is done by
+multiplexing the PAD input/output signals. For each PAD there are up to
+8 muxing options (called periph modes). Since different modules require
+different PAD settings (like pull up, keeper, etc) the contoller controls
+also the PAD settings parameters.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Atmel AT91 pin configuration node is a node of a group of pins which can be
+used for a specific device or function. This node represents both mux and config
+of the pins in that group. The 'pins' selects the function mode(also named pin
+mode) this pin can work on and the 'config' configures various pad settings
+such as pull-up, multi drive, etc.
+
+Required properties for iomux controller:
+- compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl"
+		or "atmel,sama5d3-pinctrl"
+- atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
+  configured in this periph mode. All the periph and bank need to be describe.
+
+How to create such array:
+
+Each column will represent the possible peripheral of the pinctrl
+Each line will represent a pio bank
+
+Take an example on the 9260
+Peripheral: 2 ( A and B)
+Bank: 3 (A, B and C)
+=>
+
+  /*    A         B     */
+  0xffffffff 0xffc00c3b  /* pioA */
+  0xffffffff 0x7fff3ccf  /* pioB */
+  0xffffffff 0x007fffff  /* pioC */
+
+For each peripheral/bank we will descibe in a u32 if a pin can be
+configured in it by putting 1 to the pin bit (1 << pin)
+
+Let's take the pioA on peripheral B
+From the datasheet Table 10-2.
+Peripheral B
+PA0	MCDB0
+PA1	MCCDB
+PA2
+PA3	MCDB3
+PA4	MCDB2
+PA5	MCDB1
+PA6
+PA7
+PA8
+PA9
+PA10	ETX2
+PA11	ETX3
+PA12
+PA13
+PA14
+PA15
+PA16
+PA17
+PA18
+PA19
+PA20
+PA21
+PA22	ETXER
+PA23	ETX2
+PA24	ETX3
+PA25	ERX2
+PA26	ERX3
+PA27	ERXCK
+PA28	ECRS
+PA29	ECOL
+PA30	RXD4
+PA31	TXD4
+
+=> 0xffc00c3b
+
+Required properties for pin configuration node:
+- atmel,pins: 4 integers array, represents a group of pins mux and config
+  setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
+  The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
+  PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
+
+Bits used for CONFIG:
+PULL_UP		(1 << 0): indicate this pin needs a pull up.
+MULTIDRIVE	(1 << 1): indicate this pin needs to be configured as multi-drive.
+			Multi-drive is equivalent to open-drain type output.
+DEGLITCH	(1 << 2): indicate this pin needs deglitch.
+PULL_DOWN	(1 << 3): indicate this pin needs a pull down.
+DIS_SCHMIT	(1 << 4): indicate this pin needs to the disable schmitt trigger.
+DRIVE_STRENGTH (3 << 5): indicate the drive strength of the pin using the
+			following values:
+				00 - No change (reset state value kept)
+				01 - Low
+				10 - Medium
+				11 - High
+DEBOUNCE	(1 << 16): indicate this pin needs debounce.
+DEBOUNCE_VAL	(0x3fff << 17): debounce value.
+
+NOTE:
+Some requirements for using atmel,at91rm9200-pinctrl binding:
+1. We have pin function node defined under at91 controller node to represent
+   what pinmux functions this SoC supports.
+2. The driver can use the function node's name and pin configuration node's
+   name describe the pin function and group hierarchy.
+   For example, Linux at91 pinctrl driver takes the function node's name
+   as the function name and pin configuration node's name as group name to
+   create the map table.
+3. Each pin configuration node should have a phandle, devices can set pins
+   configurations by referring to the phandle of that pin configuration node.
+4. The gpio controller must be describe in the pinctrl simple-bus.
+
+Examples:
+
+pinctrl@fffff400 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+	reg = <0xfffff400 0x600>;
+
+	atmel,mux-mask = <
+	      /*    A         B     */
+	       0xffffffff 0xffc00c3b  /* pioA */
+	       0xffffffff 0x7fff3ccf  /* pioB */
+	       0xffffffff 0x007fffff  /* pioC */
+	      >;
+
+	/* shared pinctrl settings */
+	dbgu {
+		pinctrl_dbgu: dbgu-0 {
+			atmel,pins =
+				<1 14 0x1 0x0	/* PB14 periph A */
+				 1 15 0x1 0x1>;	/* PB15 periph A with pullup */
+		};
+	};
+};
+
+dbgu: serial@fffff200 {
+	compatible = "atmel,at91sam9260-usart";
+	reg = <0xfffff200 0x200>;
+	interrupts = <1 4 7>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_dbgu>;
+	status = "disabled";
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt
new file mode 100644
index 000000000..4eaae3282
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm11351-pinctrl.txt
@@ -0,0 +1,461 @@
+Broadcom BCM281xx Pin Controller
+
+This is a pin controller for the Broadcom BCM281xx SoC family, which includes
+BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs.
+
+=== Pin Controller Node ===
+
+Required Properties:
+
+- compatible:	Must be "brcm,bcm11351-pinctrl"
+- reg:		Base address of the PAD Controller register block and the size
+		of the block.
+
+For example, the following is the bare minimum node:
+
+	pinctrl@35004800 {
+		compatible = "brcm,bcm11351-pinctrl";
+		reg = <0x35004800 0x430>;
+	};
+
+As a pin controller device, in addition to the required properties, this node
+should also contain the pin configuration nodes that client devices reference,
+if any.
+
+=== Pin Configuration Node ===
+
+Each pin configuration node is a sub-node of the pin controller node and is a
+container of an arbitrary number of subnodes, called pin group nodes in this
+document.
+
+Please refer to the pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the definition of a
+"pin configuration node".
+
+=== Pin Group Node ===
+
+A pin group node specifies the desired pin mux and/or pin configuration for an
+arbitrary number of pins.  The name of the pin group node is optional and not
+used.
+
+A pin group node only affects the properties specified in the node, and has no
+effect on any properties that are omitted.
+
+The pin group node accepts a subset of the generic pin config properties. For
+details generic pin config properties, please refer to pinctrl-bindings.txt
+and <include/linux/pinctrl/pinconfig-generic.h>.
+
+Each pin controlled by this pin controller belong to one of three types:
+Standard, I2C, and HDMI.  Each type accepts a different set of pin config
+properties.  A list of pins and their types is provided below.
+
+Required Properties (applicable to all pins):
+
+- pins:		Multiple strings.  Specifies the name(s) of one or more pins to
+		be configured by this node.
+
+Optional Properties (for standard pins):
+
+- function:			String. Specifies the pin mux selection. Values
+				must be one of: "alt1", "alt2", "alt3", "alt4"
+- input-schmitt-enable:		No arguments. Enable schmitt-trigger mode.
+- input-schmitt-disable:	No arguments. Disable schmitt-trigger mode.
+- bias-pull-up:			No arguments. Pull up on pin.
+- bias-pull-down:		No arguments. Pull down on pin.
+- bias-disable:			No arguments. Disable pin bias.
+- slew-rate:			Integer. Meaning depends on configured pin mux:
+				*_SCL or *_SDA:
+					0: Standard(100kbps)& Fast(400kbps) mode
+					1: Highspeed (3.4Mbps) mode
+				IC_DM or IC_DP:
+					0: normal slew rate
+					1: fast slew rate
+				Otherwise:
+					0: fast slew rate
+					1: normal slew rate
+- input-enable:			No arguments. Enable input (does not affect
+				output.)
+- input-disable:		No arguments. Disable input (does not affect
+				output.)
+- drive-strength:		Integer. Drive strength in mA.  Valid values are
+				2, 4, 6, 8, 10, 12, 14, 16 mA.
+
+Optional Properties (for I2C pins):
+
+- function:			String. Specifies the pin mux selection. Values
+				must be one of: "alt1", "alt2", "alt3", "alt4"
+- bias-pull-up:			Integer. Pull up strength in Ohm. There are 3
+				pull-up resisitors (1.2k, 1.8k, 2.7k) available
+				in parallel for I2C pins, so the valid values
+				are: 568, 720, 831, 1080, 1200, 1800, 2700 Ohm.
+- bias-disable:			No arguments. Disable pin bias.
+- slew-rate:			Integer. Meaning depends on configured pin mux:
+				*_SCL or *_SDA:
+					0: Standard(100kbps)& Fast(400kbps) mode
+					1: Highspeed (3.4Mbps) mode
+				IC_DM or IC_DP:
+					0: normal slew rate
+					1: fast slew rate
+				Otherwise:
+					0: fast slew rate
+					1: normal slew rate
+- input-enable:			No arguments. Enable input (does not affect
+				output.)
+- input-disable:		No arguments. Disable input (does not affect
+				output.)
+
+Optional Properties (for HDMI pins):
+
+- function:			String. Specifies the pin mux selection. Values
+				must be one of: "alt1", "alt2", "alt3", "alt4"
+- slew-rate:			Integer. Controls slew rate.
+					0: Standard(100kbps)& Fast(400kbps) mode
+					1: Highspeed (3.4Mbps) mode
+- input-enable:			No arguments. Enable input (does not affect
+				output.)
+- input-disable:		No arguments. Disable input (does not affect
+				output.)
+
+Example:
+// pin controller node
+pinctrl@35004800 {
+	compatible = "brcm,bcm11351-pinctrl";
+	reg = <0x35004800 0x430>;
+
+	// pin configuration node
+	dev_a_default: dev_a_active {
+		//group node defining 1 standard pin
+		grp_1 {
+			pins		= "std_pin1";
+			function	= "alt1";
+			input-schmitt-enable;
+			bias-disable;
+			slew-rate	= <1>;
+			drive-strength	= <4>;
+		};
+
+		// group node defining 2 I2C pins
+		grp_2 {
+			pins		= "i2c_pin1", "i2c_pin2";
+			function	= "alt2";
+			bias-pull-up	= <720>;
+			input-enable;
+		};
+
+		// group node defining 2 HDMI pins
+		grp_3 {
+			pins		= "hdmi_pin1", "hdmi_pin2";
+			function	= "alt3";
+			slew-rate	= <1>;
+		};
+
+		// other pin group nodes
+		...
+	};
+
+	// other pin configuration nodes
+	...
+};
+
+In the example above, "dev_a_active" is a pin configuration node with a number
+of sub-nodes.  In the pin group node "grp_1", one pin, "std_pin1", is defined in
+the "pins" property.  Thus, the remaining properties in the "grp_1" node applies
+only to this pin, including the following settings:
+ - setting pinmux to "alt1"
+ - enabling schmitt-trigger (hystersis) mode
+ - disabling pin bias
+ - setting the slew-rate to 1
+ - setting the drive strength to 4 mA
+Note that neither "input-enable" nor "input-disable" was specified - the pinctrl
+subsystem will therefore leave this property unchanged from whatever state it
+was in before applying these changes.
+
+The "pins" property in the pin group node "grp_2" specifies two pins -
+"i2c_pin1" and "i2c_pin2"; the remaining properties in this pin group node,
+therefore, applies to both of these pins.  The properties include:
+ - setting pinmux to "alt2"
+ - setting pull-up resistance to 720 Ohm (ie. enabling 1.2k and 1.8k resistors
+   in parallel)
+ - enabling both pins' input
+"slew-rate" is not specified in this pin group node, so the slew-rate for these
+pins are left as-is.
+
+Finally, "grp_3" defines two HDMI pins.  The following properties are applied to
+both pins:
+ - setting pinmux to "alt3"
+ - setting slew-rate to 1; for HDMI pins, this corresponds to the 3.4 Mbps
+   Highspeed mode
+The input is neither enabled or disabled, and is left untouched.
+
+=== Pin Names and Type ===
+
+The following are valid pin names and their pin types:
+
+	"adcsync",		Standard
+	"bat_rm",		Standard
+	"bsc1_scl",		I2C
+	"bsc1_sda",		I2C
+	"bsc2_scl",		I2C
+	"bsc2_sda",		I2C
+	"classgpwr",		Standard
+	"clk_cx8",		Standard
+	"clkout_0",		Standard
+	"clkout_1",		Standard
+	"clkout_2",		Standard
+	"clkout_3",		Standard
+	"clkreq_in_0",		Standard
+	"clkreq_in_1",		Standard
+	"cws_sys_req1",		Standard
+	"cws_sys_req2",		Standard
+	"cws_sys_req3",		Standard
+	"digmic1_clk",		Standard
+	"digmic1_dq",		Standard
+	"digmic2_clk",		Standard
+	"digmic2_dq",		Standard
+	"gpen13",		Standard
+	"gpen14",		Standard
+	"gpen15",		Standard
+	"gpio00",		Standard
+	"gpio01",		Standard
+	"gpio02",		Standard
+	"gpio03",		Standard
+	"gpio04",		Standard
+	"gpio05",		Standard
+	"gpio06",		Standard
+	"gpio07",		Standard
+	"gpio08",		Standard
+	"gpio09",		Standard
+	"gpio10",		Standard
+	"gpio11",		Standard
+	"gpio12",		Standard
+	"gpio13",		Standard
+	"gpio14",		Standard
+	"gps_pablank",		Standard
+	"gps_tmark",		Standard
+	"hdmi_scl",		HDMI
+	"hdmi_sda",		HDMI
+	"ic_dm",		Standard
+	"ic_dp",		Standard
+	"kp_col_ip_0",		Standard
+	"kp_col_ip_1",		Standard
+	"kp_col_ip_2",		Standard
+	"kp_col_ip_3",		Standard
+	"kp_row_op_0",		Standard
+	"kp_row_op_1",		Standard
+	"kp_row_op_2",		Standard
+	"kp_row_op_3",		Standard
+	"lcd_b_0",		Standard
+	"lcd_b_1",		Standard
+	"lcd_b_2",		Standard
+	"lcd_b_3",		Standard
+	"lcd_b_4",		Standard
+	"lcd_b_5",		Standard
+	"lcd_b_6",		Standard
+	"lcd_b_7",		Standard
+	"lcd_g_0",		Standard
+	"lcd_g_1",		Standard
+	"lcd_g_2",		Standard
+	"lcd_g_3",		Standard
+	"lcd_g_4",		Standard
+	"lcd_g_5",		Standard
+	"lcd_g_6",		Standard
+	"lcd_g_7",		Standard
+	"lcd_hsync",		Standard
+	"lcd_oe",		Standard
+	"lcd_pclk",		Standard
+	"lcd_r_0",		Standard
+	"lcd_r_1",		Standard
+	"lcd_r_2",		Standard
+	"lcd_r_3",		Standard
+	"lcd_r_4",		Standard
+	"lcd_r_5",		Standard
+	"lcd_r_6",		Standard
+	"lcd_r_7",		Standard
+	"lcd_vsync",		Standard
+	"mdmgpio0",		Standard
+	"mdmgpio1",		Standard
+	"mdmgpio2",		Standard
+	"mdmgpio3",		Standard
+	"mdmgpio4",		Standard
+	"mdmgpio5",		Standard
+	"mdmgpio6",		Standard
+	"mdmgpio7",		Standard
+	"mdmgpio8",		Standard
+	"mphi_data_0",		Standard
+	"mphi_data_1",		Standard
+	"mphi_data_2",		Standard
+	"mphi_data_3",		Standard
+	"mphi_data_4",		Standard
+	"mphi_data_5",		Standard
+	"mphi_data_6",		Standard
+	"mphi_data_7",		Standard
+	"mphi_data_8",		Standard
+	"mphi_data_9",		Standard
+	"mphi_data_10",		Standard
+	"mphi_data_11",		Standard
+	"mphi_data_12",		Standard
+	"mphi_data_13",		Standard
+	"mphi_data_14",		Standard
+	"mphi_data_15",		Standard
+	"mphi_ha0",		Standard
+	"mphi_hat0",		Standard
+	"mphi_hat1",		Standard
+	"mphi_hce0_n",		Standard
+	"mphi_hce1_n",		Standard
+	"mphi_hrd_n",		Standard
+	"mphi_hwr_n",		Standard
+	"mphi_run0",		Standard
+	"mphi_run1",		Standard
+	"mtx_scan_clk",		Standard
+	"mtx_scan_data",	Standard
+	"nand_ad_0",		Standard
+	"nand_ad_1",		Standard
+	"nand_ad_2",		Standard
+	"nand_ad_3",		Standard
+	"nand_ad_4",		Standard
+	"nand_ad_5",		Standard
+	"nand_ad_6",		Standard
+	"nand_ad_7",		Standard
+	"nand_ale",		Standard
+	"nand_cen_0",		Standard
+	"nand_cen_1",		Standard
+	"nand_cle",		Standard
+	"nand_oen",		Standard
+	"nand_rdy_0",		Standard
+	"nand_rdy_1",		Standard
+	"nand_wen",		Standard
+	"nand_wp",		Standard
+	"pc1",			Standard
+	"pc2",			Standard
+	"pmu_int",		Standard
+	"pmu_scl",		I2C
+	"pmu_sda",		I2C
+	"rfst2g_mtsloten3g",	Standard
+	"rgmii_0_rx_ctl",	Standard
+	"rgmii_0_rxc",		Standard
+	"rgmii_0_rxd_0",	Standard
+	"rgmii_0_rxd_1",	Standard
+	"rgmii_0_rxd_2",	Standard
+	"rgmii_0_rxd_3",	Standard
+	"rgmii_0_tx_ctl",	Standard
+	"rgmii_0_txc",		Standard
+	"rgmii_0_txd_0",	Standard
+	"rgmii_0_txd_1",	Standard
+	"rgmii_0_txd_2",	Standard
+	"rgmii_0_txd_3",	Standard
+	"rgmii_1_rx_ctl",	Standard
+	"rgmii_1_rxc",		Standard
+	"rgmii_1_rxd_0",	Standard
+	"rgmii_1_rxd_1",	Standard
+	"rgmii_1_rxd_2",	Standard
+	"rgmii_1_rxd_3",	Standard
+	"rgmii_1_tx_ctl",	Standard
+	"rgmii_1_txc",		Standard
+	"rgmii_1_txd_0",	Standard
+	"rgmii_1_txd_1",	Standard
+	"rgmii_1_txd_2",	Standard
+	"rgmii_1_txd_3",	Standard
+	"rgmii_gpio_0",		Standard
+	"rgmii_gpio_1",		Standard
+	"rgmii_gpio_2",		Standard
+	"rgmii_gpio_3",		Standard
+	"rtxdata2g_txdata3g1",	Standard
+	"rtxen2g_txdata3g2",	Standard
+	"rxdata3g0",		Standard
+	"rxdata3g1",		Standard
+	"rxdata3g2",		Standard
+	"sdio1_clk",		Standard
+	"sdio1_cmd",		Standard
+	"sdio1_data_0",		Standard
+	"sdio1_data_1",		Standard
+	"sdio1_data_2",		Standard
+	"sdio1_data_3",		Standard
+	"sdio4_clk",		Standard
+	"sdio4_cmd",		Standard
+	"sdio4_data_0",		Standard
+	"sdio4_data_1",		Standard
+	"sdio4_data_2",		Standard
+	"sdio4_data_3",		Standard
+	"sim_clk",		Standard
+	"sim_data",		Standard
+	"sim_det",		Standard
+	"sim_resetn",		Standard
+	"sim2_clk",		Standard
+	"sim2_data",		Standard
+	"sim2_det",		Standard
+	"sim2_resetn",		Standard
+	"sri_c",		Standard
+	"sri_d",		Standard
+	"sri_e",		Standard
+	"ssp_extclk",		Standard
+	"ssp0_clk",		Standard
+	"ssp0_fs",		Standard
+	"ssp0_rxd",		Standard
+	"ssp0_txd",		Standard
+	"ssp2_clk",		Standard
+	"ssp2_fs_0",		Standard
+	"ssp2_fs_1",		Standard
+	"ssp2_fs_2",		Standard
+	"ssp2_fs_3",		Standard
+	"ssp2_rxd_0",		Standard
+	"ssp2_rxd_1",		Standard
+	"ssp2_txd_0",		Standard
+	"ssp2_txd_1",		Standard
+	"ssp3_clk",		Standard
+	"ssp3_fs",		Standard
+	"ssp3_rxd",		Standard
+	"ssp3_txd",		Standard
+	"ssp4_clk",		Standard
+	"ssp4_fs",		Standard
+	"ssp4_rxd",		Standard
+	"ssp4_txd",		Standard
+	"ssp5_clk",		Standard
+	"ssp5_fs",		Standard
+	"ssp5_rxd",		Standard
+	"ssp5_txd",		Standard
+	"ssp6_clk",		Standard
+	"ssp6_fs",		Standard
+	"ssp6_rxd",		Standard
+	"ssp6_txd",		Standard
+	"stat_1",		Standard
+	"stat_2",		Standard
+	"sysclken",		Standard
+	"traceclk",		Standard
+	"tracedt00",		Standard
+	"tracedt01",		Standard
+	"tracedt02",		Standard
+	"tracedt03",		Standard
+	"tracedt04",		Standard
+	"tracedt05",		Standard
+	"tracedt06",		Standard
+	"tracedt07",		Standard
+	"tracedt08",		Standard
+	"tracedt09",		Standard
+	"tracedt10",		Standard
+	"tracedt11",		Standard
+	"tracedt12",		Standard
+	"tracedt13",		Standard
+	"tracedt14",		Standard
+	"tracedt15",		Standard
+	"txdata3g0",		Standard
+	"txpwrind",		Standard
+	"uartb1_ucts",		Standard
+	"uartb1_urts",		Standard
+	"uartb1_urxd",		Standard
+	"uartb1_utxd",		Standard
+	"uartb2_urxd",		Standard
+	"uartb2_utxd",		Standard
+	"uartb3_ucts",		Standard
+	"uartb3_urts",		Standard
+	"uartb3_urxd",		Standard
+	"uartb3_utxd",		Standard
+	"uartb4_ucts",		Standard
+	"uartb4_urts",		Standard
+	"uartb4_urxd",		Standard
+	"uartb4_utxd",		Standard
+	"vc_cam1_scl",		I2C
+	"vc_cam1_sda",		I2C
+	"vc_cam2_scl",		I2C
+	"vc_cam2_sda",		I2C
+	"vc_cam3_scl",		I2C
+	"vc_cam3_sda",		I2C
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt
new file mode 100644
index 000000000..2569866c6
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt
@@ -0,0 +1,74 @@
+Broadcom BCM2835 GPIO (and pinmux) controller
+
+The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
+controller, and pinmux/control device.
+
+Required properties:
+- compatible: "brcm,bcm2835-gpio"
+- reg: Should contain the physical address of the GPIO module's registers.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters:
+  - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- interrupts : The interrupt outputs from the controller. One interrupt per
+  individual bank followed by the "all banks" interrupt.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.
+  The first cell is the GPIO number.
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+    Valid combinations are 1, 2, 3, 4, 8.
+
+Please refer to ../gpio/gpio.txt for a general description of GPIO bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Each pin configuration node lists the pin(s) to which it applies, and one or
+more of the mux function to select on those pin(s), and pull-up/down
+configuration. Each subnode only affects those parameters that are explicitly
+listed. In other words, a subnode that lists only a mux function implies no
+information about any pull configuration. Similarly, a subnode that lists only
+a pul parameter implies no information about the mux function.
+
+Required subnode-properties:
+- brcm,pins: An array of cells. Each cell contains the ID of a pin. Valid IDs
+  are the integer GPIO IDs; 0==GPIO0, 1==GPIO1, ... 53==GPIO53.
+
+Optional subnode-properties:
+- brcm,function: Integer, containing the function to mux to the pin(s):
+  0: GPIO in
+  1: GPIO out
+  2: alt5
+  3: alt4
+  4: alt0
+  5: alt1
+  6: alt2
+  7: alt3
+- brcm,pull: Integer, representing the pull-down/up to apply to the pin(s):
+  0: none
+  1: down
+  2: up
+
+Each of brcm,function and brcm,pull may contain either a single value which
+will be applied to all pins in brcm,pins, or 1 value for each entry in
+brcm,pins.
+
+Example:
+
+	gpio: gpio {
+		compatible = "brcm,bcm2835-gpio";
+		reg = <0x2200000 0xb4>;
+		interrupts = <2 17>, <2 19>, <2 18>, <2 20>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt
new file mode 100644
index 000000000..6540ca56b
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt
@@ -0,0 +1,98 @@
+Broadcom Cygnus GPIO/PINCONF Controller
+
+Required properties:
+
+- compatible:
+    Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or
+    "brcm,cygnus-crmu-gpio"
+
+- reg:
+    Define the base and range of the I/O address space that contains the Cygnus
+GPIO/PINCONF controller registers
+
+- #gpio-cells:
+    Must be two. The first cell is the GPIO pin number (within the
+controller's pin space) and the second cell is used for the following:
+    bit[0]: polarity (0 for active high and 1 for active low)
+
+- gpio-controller:
+    Specifies that the node is a GPIO controller
+
+Optional properties:
+
+- interrupts:
+    Interrupt ID
+
+- interrupt-controller:
+    Specifies that the node is an interrupt controller
+
+- pinmux:
+    Specifies the phandle to the IOMUX device, where pins can be individually
+muxed to GPIO
+
+Supported generic PINCONF properties in child nodes:
+
+- pins:
+    The list of pins (within the controller's own pin space) that properties
+in the node apply to. Pin names are "gpio-<pin>"
+
+- bias-disable:
+    Disable pin bias
+
+- bias-pull-up:
+    Enable internal pull up resistor
+
+- bias-pull-down:
+    Enable internal pull down resistor
+
+- drive-strength:
+    Valid drive strength values include 2, 4, 6, 8, 10, 12, 14, 16 (mA)
+
+Example:
+	gpio_ccm: gpio@1800a000 {
+		compatible = "brcm,cygnus-ccm-gpio";
+		reg = <0x1800a000 0x50>,
+		      <0x0301d164 0x20>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+
+		touch_pins: touch_pins {
+			pwr: pwr {
+				pins = "gpio-0";
+				drive-strength = <16>;
+			};
+
+			event: event {
+				pins = "gpio-1";
+				bias-pull-up;
+			};
+		};
+	};
+
+	gpio_asiu: gpio@180a5000 {
+		compatible = "brcm,cygnus-asiu-gpio";
+		reg = <0x180a5000 0x668>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+	};
+
+	/*
+	 * Touchscreen that uses the CCM GPIO 0 and 1
+	 */
+	tsc {
+		...
+		...
+		gpio-pwr = <&gpio_ccm 0 0>;
+		gpio-event = <&gpio_ccm 1 0>;
+	};
+
+	/* Bluetooth that uses the ASIU GPIO 5, with polarity inverted */
+	bluetooth {
+		...
+		...
+		bcm,rfkill-bank-sel = <&gpio_asiu 5 1>
+	}
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt
new file mode 100644
index 000000000..3600d5c6c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt
@@ -0,0 +1,132 @@
+Broadcom Cygnus IOMUX Controller
+
+The Cygnus IOMUX controller supports group based mux configuration. In
+addition, certain pins can be muxed to GPIO function individually.
+
+Required properties:
+
+- compatible:
+    Must be "brcm,cygnus-pinmux"
+
+- reg:
+    Define the base and range of the I/O address space that contains the Cygnus
+IOMUX registers
+
+Properties in subnodes:
+
+- function:
+    The mux function to select
+
+- groups:
+    The list of groups to select with a given function
+
+For more details, refer to
+Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+For example:
+
+	pinmux: pinmux@0x0301d0c8 {
+		compatible = "brcm,cygnus-pinmux";
+		reg = <0x0301d0c8 0x1b0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s0_default>;
+
+		i2s0_default: i2s0_default {
+			mux {
+				function = "i2s0";
+				groups = "i2s0_0_grp", "i2s0_1_grp";
+			};
+		};
+	};
+
+List of supported functions and groups in Cygnus:
+
+"i2s0": "i2s0_0_grp", "i2s0_1_grp"
+
+"i2s1": "i2s1_0_grp", "i2s1_1_grp"
+
+"i2s2": "i2s2_0_grp", "i2s2_1_grp", "i2s2_2_grp", "i2s2_3_grp", "i2s2_4_grp"
+
+"spdif": "spdif_grp"
+
+"pwm0": "pwm0_grp"
+
+"pwm1": "pwm1_grp"
+
+"pwm2": "pwm2_grp"
+
+"pwm3": "pwm3_grp"
+
+"pwm4": "pwm4_grp"
+
+"pwm5": "pwm5_grp"
+
+"key": "key0_grp", "key1_grp", "key2_grp", "key3_grp", "key4_grp", "key5_grp",
+"key6_grp", "key7_grp", "key8_grp", "key9_grp", "key10_grp", "key11_grp",
+"key12_grp", "key13_grp", "key14_grp", "key15_grp"
+
+"audio_dte": "audio_dte0_grp", "audio_dte1_grp", "audio_dte2_grp", "audio_dte3_grp"
+
+"smart_card0": "smart_card0_grp", "smart_card0_fcb_grp"
+
+"smart_card1": "smart_card1_grp", "smart_card1_fcb_grp"
+
+"spi0": "spi0_grp"
+
+"spi1": "spi1_grp"
+
+"spi2": "spi2_grp"
+
+"spi3": "spi3_grp"
+
+"spi4": "spi4_0_grp", "spi4_1_grp"
+
+"spi5": "spi5_grp"
+
+"sw_led0": "sw_led0_0_grp", "sw_led0_1_grp"
+
+"sw_led1": "sw_led1_grp"
+
+"sw_led2": "sw_led2_0_grp", "sw_led2_1_grp"
+
+"d1w": "d1w_grp"
+
+"lcd": "lcd_grp"
+
+"sram": "sram_0_grp", "sram_1_grp"
+
+"uart0": "uart0_grp"
+
+"uart1": "uart1_grp", "uart1_dte_grp"
+
+"uart2": "uart2_grp"
+
+"uart3": "uart3_grp"
+
+"uart4": "uart4_grp"
+
+"qspi": "qspi_0_grp", "qspi_1_grp"
+
+"nand": "nand_grp"
+
+"sdio0": "sdio0_grp", "sdio0_cd_grp", "sdio0_mmc_grp"
+
+"sdio1": "sdio1_data_0_grp", "sdio1_data_1_grp", "sdio1_cd_grp",
+"sdio1_led_grp", "sdio1_mmc_grp"
+
+"can0": "can0_grp"
+
+"can1": "can1_grp"
+
+"cam": "cam_led_grp", "cam_0_grp", "cam_1_grp"
+
+"bsc1": "bsc1_grp"
+
+"pcie_clkreq": "pcie_clkreq_grp"
+
+"usb0_oc": "usb0_oc_grp"
+
+"usb1_oc": "usb1_oc_grp"
+
+"usb2_oc": "usb2_oc_grp"
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt
new file mode 100644
index 000000000..9fde25f14
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx-pinctrl.txt
@@ -0,0 +1,94 @@
+* Freescale IOMUX Controller (IOMUXC) for i.MX
+
+The IOMUX Controller (IOMUXC), together with the IOMUX, enables the IC
+to share one PAD to several functional blocks. The sharing is done by
+multiplexing the PAD input/output signals. For each PAD there are up to
+8 muxing options (called ALT modes). Since different modules require
+different PAD settings (like pull up, keeper, etc) the IOMUXC controls
+also the PAD settings parameters.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Freescale IMX pin configuration node is a node of a group of pins which can be
+used for a specific device or function. This node represents both mux and config
+of the pins in that group. The 'mux' selects the function mode(also named mux
+mode) this pin can work on and the 'config' configures various pad settings
+such as pull-up, open drain, drive strength, etc.
+
+Required properties for iomux controller:
+- compatible: "fsl,<soc>-iomuxc"
+  Please refer to each fsl,<soc>-pinctrl.txt binding doc for supported SoCs.
+
+Required properties for pin configuration node:
+- fsl,pins: each entry consists of 6 integers and represents the mux and config
+  setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val
+  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
+  imx*-pinfunc.h under device tree source folder. The last integer CONFIG is
+  the pad setting value like pull-up on this pin. And that's why fsl,pins entry
+  looks like <PIN_FUNC_ID CONFIG> in the example below.
+
+Bits used for CONFIG:
+NO_PAD_CTL(1 << 31): indicate this pin does not need config.
+
+SION(1 << 30): Software Input On Field.
+Force the selected mux mode input path no matter of MUX_MODE functionality.
+By default the input path is determined by functionality of the selected
+mux mode (regular).
+
+Other bits are used for PAD setting.
+Please refer to each fsl,<soc>-pinctrl,txt binding doc for SoC specific part
+of bits definitions.
+
+NOTE:
+Some requirements for using fsl,imx-pinctrl binding:
+1. We have pin function node defined under iomux controller node to represent
+   what pinmux functions this SoC supports.
+2. The pin configuration node intends to work on a specific function should
+   to be defined under that specific function node.
+   The function node's name should represent well about what function
+   this group of pins in this pin configuration node are working on.
+3. The driver can use the function node's name and pin configuration node's
+   name describe the pin function and group hierarchy.
+   For example, Linux IMX pinctrl driver takes the function node's name
+   as the function name and pin configuration node's name as group name to
+   create the map table.
+4. Each pin configuration node should have a phandle, devices can set pins
+   configurations by referring to the phandle of that pin configuration node.
+
+Examples:
+usdhc@0219c000 { /* uSDHC4 */
+	non-removable;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4_1>;
+};
+
+iomuxc@020e0000 {
+	compatible = "fsl,imx6q-iomuxc";
+	reg = <0x020e0000 0x4000>;
+
+	/* shared pinctrl settings */
+	usdhc4 {
+		pinctrl_usdhc4_1: usdhc4grp-1 {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_CMD__SD4_CMD    0x17059
+				MX6QDL_PAD_SD4_CLK__SD4_CLK    0x10059
+				MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+				MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+				MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+				MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+				MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+				MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+				MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+				MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+			>;
+	};
+	....
+};
+Refer to the IOMUXC controller chapter in imx6q datasheet,
+0x17059 means enable hysteresis, 47KOhm Pull Up, 50Mhz speed,
+80Ohm driver strength and Fast Slew Rate.
+User should refer to each SoC spec to set the correct value.
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx25-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx25-pinctrl.txt
new file mode 100644
index 000000000..fd653bde1
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx25-pinctrl.txt
@@ -0,0 +1,23 @@
+* Freescale IMX25 IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+CONFIG bits definition:
+PAD_CTL_HYS			(1 << 8)
+PAD_CTL_PKE			(1 << 7)
+PAD_CTL_PUE			(1 << 6)
+PAD_CTL_PUS_100K_DOWN		(0 << 4)
+PAD_CTL_PUS_47K_UP		(1 << 4)
+PAD_CTL_PUS_100K_UP		(2 << 4)
+PAD_CTL_PUS_22K_UP		(3 << 4)
+PAD_CTL_ODE_CMOS		(0 << 3)
+PAD_CTL_ODE_OPENDRAIN		(1 << 3)
+PAD_CTL_DSE_NOMINAL		(0 << 1)
+PAD_CTL_DSE_HIGH		(1 << 1)
+PAD_CTL_DSE_MAX			(2 << 1)
+PAD_CTL_SRE_FAST		(1 << 0)
+PAD_CTL_SRE_SLOW		(0 << 0)
+
+Refer to imx25-pinfunc.h in device tree source folder for all available
+imx25 PIN_FUNC_ID.
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt
new file mode 100644
index 000000000..d1706ea82
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt
@@ -0,0 +1,121 @@
+* Freescale IMX27 IOMUX Controller
+
+Required properties:
+- compatible: "fsl,imx27-iomuxc"
+
+The iomuxc driver node should define subnodes containing of pinctrl configuration subnodes.
+
+Required properties for pin configuration node:
+- fsl,pins: three integers array, represents a group of pins mux and config
+  setting. The format is fsl,pins = <PIN MUX_ID CONFIG>.
+
+  PIN is an integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable
+  configurable pins each. PIN is PORT * 32 + PORT_PIN, PORT_PIN is the pin
+  number on the specific port (between 0 and 31).
+
+  MUX_ID is
+    function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10)
+
+      function value is used to select the pin function.
+      Possible values:
+          0 - Primary function
+          1 - Alternate function
+          2 - GPIO
+      Registers: GIUS (GPIO In Use), GPR (General Purpose Register)
+
+      direction defines the data direction of the pin.
+      Possible values:
+          0 - Input
+          1 - Output
+      Register: DDIR
+
+      gpio_oconf configures the gpio submodule output signal. This does not
+      have any effect unless GPIO function is selected. A/B/C_IN are output
+      signals of function blocks A,B and C. Specific function blocks are
+      described in the reference manual.
+      Possible values:
+          0 - A_IN
+          1 - B_IN
+          2 - C_IN
+          3 - Data Register
+      Registers: OCR1, OCR2
+
+      gpio_iconfa/b configures the gpio submodule input to functionblocks A and
+      B. GPIO function should be selected if this is configured.
+      Possible values:
+          0 - GPIO_IN
+          1 - Interrupt Status Register
+          2 - Pulldown
+          3 - Pullup
+      Registers ICONFA1, ICONFA2, ICONFB1 and ICONFB2
+
+  CONFIG can be 0 or 1, meaning Pullup disable/enable.
+
+
+The iomux controller has gpio child nodes which are embedded in the iomux
+control registers. They have to be defined as child nodes of the iomux device
+node. If gpio subnodes are defined "#address-cells", "#size-cells" and "ranges"
+properties for the iomux device node are required.
+
+Example:
+
+iomuxc: iomuxc@10015000 {
+	compatible = "fsl,imx27-iomuxc";
+	reg = <0x10015000 0x600>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	gpio1: gpio@10015000 {
+		...
+	};
+
+	...
+
+	uart {
+		pinctrl_uart1: uart-1 {
+			fsl,pins = <
+				0x8c 0x004 0x0 /* UART1_TXD__UART1_TXD */
+				0x8d 0x000 0x0 /* UART1_RXD__UART1_RXD */
+				0x8e 0x004 0x0 /* UART1_CTS__UART1_CTS */
+				0x8f 0x000 0x0 /* UART1_RTS__UART1_RTS */
+			>;
+		};
+
+		...
+	};
+};
+
+
+For convenience there are macros defined in imx27-pinfunc.h which provide PIN
+and MUX_ID. They are structured as MX27_PAD_<Pad name>__<Signal name>. The names
+are defined in the i.MX27 reference manual.
+
+The above example using macros:
+
+iomuxc: iomuxc@10015000 {
+	compatible = "fsl,imx27-iomuxc";
+	reg = <0x10015000 0x600>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	gpio1: gpio@10015000 {
+		...
+	};
+
+	...
+
+	uart {
+		pinctrl_uart1: uart-1 {
+			fsl,pins = <
+				MX27_PAD_UART1_TXD__UART1_TXD 0x0
+				MX27_PAD_UART1_RXD__UART1_RXD 0x0
+				MX27_PAD_UART1_CTS__UART1_CTS 0x0
+				MX27_PAD_UART1_RTS__UART1_RTS 0x0
+			>;
+		};
+
+		...
+	};
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx35-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx35-pinctrl.txt
new file mode 100644
index 000000000..c083dfd25
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx35-pinctrl.txt
@@ -0,0 +1,33 @@
+* Freescale IMX35 IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx35-iomuxc"
+- fsl,pins: two integers array, represents a group of pins mux and config
+  setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
+  pin working on a specific function, CONFIG is the pad setting value like
+  pull-up for this pin. Please refer to imx35 datasheet for the valid pad
+  config settings.
+
+CONFIG bits definition:
+PAD_CTL_DRIVE_VOLAGAGE_18	(1 << 13)
+PAD_CTL_DRIVE_VOLAGAGE_33	(0 << 13)
+PAD_CTL_HYS			(1 << 8)
+PAD_CTL_PKE			(1 << 7)
+PAD_CTL_PUE			(1 << 6)
+PAD_CTL_PUS_100K_DOWN		(0 << 4)
+PAD_CTL_PUS_47K_UP		(1 << 4)
+PAD_CTL_PUS_100K_UP		(2 << 4)
+PAD_CTL_PUS_22K_UP		(3 << 4)
+PAD_CTL_ODE_CMOS		(0 << 3)
+PAD_CTL_ODE_OPENDRAIN		(1 << 3)
+PAD_CTL_DSE_NOMINAL		(0 << 1)
+PAD_CTL_DSE_HIGH		(1 << 1)
+PAD_CTL_DSE_MAX			(2 << 1)
+PAD_CTL_SRE_FAST		(1 << 0)
+PAD_CTL_SRE_SLOW		(0 << 0)
+
+Refer to imx35-pinfunc.h in device tree source folder for all available
+imx35 PIN_FUNC_ID.
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx51-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx51-pinctrl.txt
new file mode 100644
index 000000000..4d1408fcc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx51-pinctrl.txt
@@ -0,0 +1,32 @@
+* Freescale IMX51 IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx51-iomuxc"
+- fsl,pins: two integers array, represents a group of pins mux and config
+  setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
+  pin working on a specific function, CONFIG is the pad setting value like
+  pull-up for this pin. Please refer to imx51 datasheet for the valid pad
+  config settings.
+
+CONFIG bits definition:
+PAD_CTL_HVE			(1 << 13)
+PAD_CTL_HYS			(1 << 8)
+PAD_CTL_PKE			(1 << 7)
+PAD_CTL_PUE			(1 << 6)
+PAD_CTL_PUS_100K_DOWN		(0 << 4)
+PAD_CTL_PUS_47K_UP		(1 << 4)
+PAD_CTL_PUS_100K_UP		(2 << 4)
+PAD_CTL_PUS_22K_UP		(3 << 4)
+PAD_CTL_ODE			(1 << 3)
+PAD_CTL_DSE_LOW			(0 << 1)
+PAD_CTL_DSE_MED			(1 << 1)
+PAD_CTL_DSE_HIGH		(2 << 1)
+PAD_CTL_DSE_MAX			(3 << 1)
+PAD_CTL_SRE_FAST		(1 << 0)
+PAD_CTL_SRE_SLOW		(0 << 0)
+
+Refer to imx51-pinfunc.h in device tree source folder for all available
+imx51 PIN_FUNC_ID.
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx53-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx53-pinctrl.txt
new file mode 100644
index 000000000..25dcb77cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx53-pinctrl.txt
@@ -0,0 +1,32 @@
+* Freescale IMX53 IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx53-iomuxc"
+- fsl,pins: two integers array, represents a group of pins mux and config
+  setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
+  pin working on a specific function, CONFIG is the pad setting value like
+  pull-up for this pin. Please refer to imx53 datasheet for the valid pad
+  config settings.
+
+CONFIG bits definition:
+PAD_CTL_HVE			(1 << 13)
+PAD_CTL_HYS			(1 << 8)
+PAD_CTL_PKE			(1 << 7)
+PAD_CTL_PUE			(1 << 6)
+PAD_CTL_PUS_100K_DOWN		(0 << 4)
+PAD_CTL_PUS_47K_UP		(1 << 4)
+PAD_CTL_PUS_100K_UP		(2 << 4)
+PAD_CTL_PUS_22K_UP		(3 << 4)
+PAD_CTL_ODE			(1 << 3)
+PAD_CTL_DSE_LOW			(0 << 1)
+PAD_CTL_DSE_MED			(1 << 1)
+PAD_CTL_DSE_HIGH		(2 << 1)
+PAD_CTL_DSE_MAX			(3 << 1)
+PAD_CTL_SRE_FAST		(1 << 0)
+PAD_CTL_SRE_SLOW		(0 << 0)
+
+Refer to imx53-pinfunc.h in device tree source folder for all available
+imx53 PIN_FUNC_ID.
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6dl-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6dl-pinctrl.txt
new file mode 100644
index 000000000..0ac5bee87
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6dl-pinctrl.txt
@@ -0,0 +1,38 @@
+* Freescale IMX6 DualLite/Solo IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx6dl-iomuxc"
+- fsl,pins: two integers array, represents a group of pins mux and config
+  setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
+  pin working on a specific function, CONFIG is the pad setting value like
+  pull-up for this pin. Please refer to imx6dl datasheet for the valid pad
+  config settings.
+
+CONFIG bits definition:
+PAD_CTL_HYS                     (1 << 16)
+PAD_CTL_PUS_100K_DOWN           (0 << 14)
+PAD_CTL_PUS_47K_UP              (1 << 14)
+PAD_CTL_PUS_100K_UP             (2 << 14)
+PAD_CTL_PUS_22K_UP              (3 << 14)
+PAD_CTL_PUE                     (1 << 13)
+PAD_CTL_PKE                     (1 << 12)
+PAD_CTL_ODE                     (1 << 11)
+PAD_CTL_SPEED_LOW               (1 << 6)
+PAD_CTL_SPEED_MED               (2 << 6)
+PAD_CTL_SPEED_HIGH              (3 << 6)
+PAD_CTL_DSE_DISABLE             (0 << 3)
+PAD_CTL_DSE_240ohm              (1 << 3)
+PAD_CTL_DSE_120ohm              (2 << 3)
+PAD_CTL_DSE_80ohm               (3 << 3)
+PAD_CTL_DSE_60ohm               (4 << 3)
+PAD_CTL_DSE_48ohm               (5 << 3)
+PAD_CTL_DSE_40ohm               (6 << 3)
+PAD_CTL_DSE_34ohm               (7 << 3)
+PAD_CTL_SRE_FAST                (1 << 0)
+PAD_CTL_SRE_SLOW                (0 << 0)
+
+Refer to imx6dl-pinfunc.h in device tree source folder for all available
+imx6dl PIN_FUNC_ID.
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt
new file mode 100644
index 000000000..546610cf2
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6q-pinctrl.txt
@@ -0,0 +1,38 @@
+* Freescale IMX6Q IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx6q-iomuxc"
+- fsl,pins: two integers array, represents a group of pins mux and config
+  setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
+  pin working on a specific function, CONFIG is the pad setting value like
+  pull-up for this pin. Please refer to imx6q datasheet for the valid pad
+  config settings.
+
+CONFIG bits definition:
+PAD_CTL_HYS                     (1 << 16)
+PAD_CTL_PUS_100K_DOWN           (0 << 14)
+PAD_CTL_PUS_47K_UP              (1 << 14)
+PAD_CTL_PUS_100K_UP             (2 << 14)
+PAD_CTL_PUS_22K_UP              (3 << 14)
+PAD_CTL_PUE                     (1 << 13)
+PAD_CTL_PKE                     (1 << 12)
+PAD_CTL_ODE                     (1 << 11)
+PAD_CTL_SPEED_LOW               (1 << 6)
+PAD_CTL_SPEED_MED               (2 << 6)
+PAD_CTL_SPEED_HIGH              (3 << 6)
+PAD_CTL_DSE_DISABLE             (0 << 3)
+PAD_CTL_DSE_240ohm              (1 << 3)
+PAD_CTL_DSE_120ohm              (2 << 3)
+PAD_CTL_DSE_80ohm               (3 << 3)
+PAD_CTL_DSE_60ohm               (4 << 3)
+PAD_CTL_DSE_48ohm               (5 << 3)
+PAD_CTL_DSE_40ohm               (6 << 3)
+PAD_CTL_DSE_34ohm               (7 << 3)
+PAD_CTL_SRE_FAST                (1 << 0)
+PAD_CTL_SRE_SLOW                (0 << 0)
+
+Refer to imx6q-pinfunc.h in device tree source folder for all available
+imx6q PIN_FUNC_ID.
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6sl-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sl-pinctrl.txt
new file mode 100644
index 000000000..e5f6d1f06
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sl-pinctrl.txt
@@ -0,0 +1,39 @@
+* Freescale IMX6 SoloLite IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx6sl-iomuxc"
+- fsl,pins: two integers array, represents a group of pins mux and config
+  setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a
+  pin working on a specific function, CONFIG is the pad setting value like
+  pull-up for this pin. Please refer to imx6sl datasheet for the valid pad
+  config settings.
+
+CONFIG bits definition:
+PAD_CTL_LVE                     (1 << 22)
+PAD_CTL_HYS                     (1 << 16)
+PAD_CTL_PUS_100K_DOWN           (0 << 14)
+PAD_CTL_PUS_47K_UP              (1 << 14)
+PAD_CTL_PUS_100K_UP             (2 << 14)
+PAD_CTL_PUS_22K_UP              (3 << 14)
+PAD_CTL_PUE                     (1 << 13)
+PAD_CTL_PKE                     (1 << 12)
+PAD_CTL_ODE                     (1 << 11)
+PAD_CTL_SPEED_LOW               (1 << 6)
+PAD_CTL_SPEED_MED               (2 << 6)
+PAD_CTL_SPEED_HIGH              (3 << 6)
+PAD_CTL_DSE_DISABLE             (0 << 3)
+PAD_CTL_DSE_240ohm              (1 << 3)
+PAD_CTL_DSE_120ohm              (2 << 3)
+PAD_CTL_DSE_80ohm               (3 << 3)
+PAD_CTL_DSE_60ohm               (4 << 3)
+PAD_CTL_DSE_48ohm               (5 << 3)
+PAD_CTL_DSE_40ohm               (6 << 3)
+PAD_CTL_DSE_34ohm               (7 << 3)
+PAD_CTL_SRE_FAST                (1 << 0)
+PAD_CTL_SRE_SLOW                (0 << 0)
+
+Refer to imx6sl-pinfunc.h in device tree source folder for all available
+imx6sl PIN_FUNC_ID.
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt
new file mode 100644
index 000000000..b1b595220
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6sx-pinctrl.txt
@@ -0,0 +1,36 @@
+* Freescale i.MX6 SoloX IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx6sx-iomuxc"
+- fsl,pins: each entry consists of 6 integers and represents the mux and config
+  setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
+  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
+  imx6sx-pinfunc.h under device tree source folder.  The last integer CONFIG is
+  the pad setting value like pull-up on this pin.  Please refer to i.MX6 SoloX
+  Reference Manual for detailed CONFIG settings.
+
+CONFIG bits definition:
+PAD_CTL_HYS                     (1 << 16)
+PAD_CTL_PUS_100K_DOWN           (0 << 14)
+PAD_CTL_PUS_47K_UP              (1 << 14)
+PAD_CTL_PUS_100K_UP             (2 << 14)
+PAD_CTL_PUS_22K_UP              (3 << 14)
+PAD_CTL_PUE                     (1 << 13)
+PAD_CTL_PKE                     (1 << 12)
+PAD_CTL_ODE                     (1 << 11)
+PAD_CTL_SPEED_LOW               (0 << 6)
+PAD_CTL_SPEED_MED               (1 << 6)
+PAD_CTL_SPEED_HIGH              (3 << 6)
+PAD_CTL_DSE_DISABLE             (0 << 3)
+PAD_CTL_DSE_260ohm              (1 << 3)
+PAD_CTL_DSE_130ohm              (2 << 3)
+PAD_CTL_DSE_87ohm               (3 << 3)
+PAD_CTL_DSE_65ohm               (4 << 3)
+PAD_CTL_DSE_52ohm               (5 << 3)
+PAD_CTL_DSE_43ohm               (6 << 3)
+PAD_CTL_DSE_37ohm               (7 << 3)
+PAD_CTL_SRE_FAST                (1 << 0)
+PAD_CTL_SRE_SLOW                (0 << 0)
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt
new file mode 100644
index 000000000..1e70a8aff
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt
@@ -0,0 +1,127 @@
+* Freescale MXS Pin Controller
+
+The pins controlled by mxs pin controller are organized in banks, each bank
+has 32 pins.  Each pin has 4 multiplexing functions, and generally, the 4th
+function is GPIO.  The configuration on the pins includes drive strength,
+voltage and pull-up.
+
+Required properties:
+- compatible: "fsl,imx23-pinctrl" or "fsl,imx28-pinctrl"
+- reg: Should contain the register physical address and length for the
+  pin controller.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices.
+
+The node of mxs pin controller acts as a container for an arbitrary number of
+subnodes.  Each of these subnodes represents some desired configuration for
+a group of pins, and only affects those parameters that are explicitly listed.
+In other words, a subnode that describes a drive strength parameter implies no
+information about pull-up. For this reason, even seemingly boolean values are
+actually tristates in this binding: unspecified, off, or on. Unspecified is
+represented as an absent property, and off/on are represented as integer
+values 0 and 1.
+
+Those subnodes under mxs pin controller node will fall into two categories.
+One is to set up a group of pins for a function, both mux selection and pin
+configurations, and it's called group node in the binding document.   The other
+one is to adjust the pin configuration for some particular pins that need a
+different configuration than what is defined in group node.  The binding
+document calls this type of node config node.
+
+On mxs, there is no hardware pin group. The pin group in this binding only
+means a group of pins put together for particular peripheral to work in
+particular function, like SSP0 functioning as mmc0-8bit.  That said, the
+group node should include all the pins needed for one function rather than
+having these pins defined in several group nodes.  It also means each of
+"pinctrl-*" phandle in client device node should only have one group node
+pointed in there, while the phandle can have multiple config node referenced
+there to adjust configurations for some pins in the group.
+
+Required subnode-properties:
+- fsl,pinmux-ids: An integer array.  Each integer in the array specify a pin
+  with given mux function, with bank, pin and mux packed as below.
+
+    [15..12] : bank number
+    [11..4]  : pin number
+    [3..0]   : mux selection
+
+  This integer with mux selection packed is used as an entity by both group
+  and config nodes to identify a pin.  The mux selection in the integer takes
+  effects only on group node, and will get ignored by driver with config node,
+  since config node is only meant to set up pin configurations.
+
+  Valid values for these integers are listed below.
+
+- reg: Should be the index of the group nodes for same function.  This property
+  is required only for group nodes, and should not be present in any config
+  nodes.
+
+Optional subnode-properties:
+- fsl,drive-strength: Integer.
+    0: MXS_DRIVE_4mA
+    1: MXS_DRIVE_8mA
+    2: MXS_DRIVE_12mA
+    3: MXS_DRIVE_16mA
+- fsl,voltage: Integer.
+    0: MXS_VOLTAGE_LOW  - 1.8 V
+    1: MXS_VOLTAGE_HIGH - 3.3 V
+- fsl,pull-up: Integer.
+    0: MXS_PULL_DISABLE - Disable the internal pull-up
+    1: MXS_PULL_ENABLE  - Enable the internal pull-up
+
+Note that when enabling the pull-up, the internal pad keeper gets disabled.
+Also, some pins doesn't have a pull up, in that case, setting the fsl,pull-up
+will only disable the internal pad keeper.
+
+Examples:
+
+pinctrl@80018000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-pinctrl";
+	reg = <0x80018000 2000>;
+
+	mmc0_8bit_pins_a: mmc0-8bit@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA0__SSP0_D0
+			MX28_PAD_SSP0_DATA1__SSP0_D1
+			MX28_PAD_SSP0_DATA2__SSP0_D2
+			MX28_PAD_SSP0_DATA3__SSP0_D3
+			MX28_PAD_SSP0_DATA4__SSP0_D4
+			MX28_PAD_SSP0_DATA5__SSP0_D5
+			MX28_PAD_SSP0_DATA6__SSP0_D6
+			MX28_PAD_SSP0_DATA7__SSP0_D7
+			MX28_PAD_SSP0_CMD__SSP0_CMD
+			MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
+			MX28_PAD_SSP0_SCK__SSP0_SCK
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	mmc_cd_cfg: mmc-cd-cfg {
+		fsl,pinmux-ids = <MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mmc_sck_cfg: mmc-sck-cfg {
+		fsl,pinmux-ids = <MX28_PAD_SSP0_SCK__SSP0_SCK>;
+		fsl,drive-strength = <MXS_DRIVE_12mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+In this example, group node mmc0-8bit defines a group of pins for mxs SSP0
+to function as a 8-bit mmc device, with 8mA, 3.3V and pull-up configurations
+applied on all these pins.  And config nodes mmc-cd-cfg and mmc-sck-cfg are
+adjusting the configuration for pins card-detection and clock from what group
+node mmc0-8bit defines.  Only the configuration properties to be adjusted need
+to be listed in the config nodes.
+
+Valid values for i.MX28/i.MX23 pinmux-id are defined in
+arch/arm/boot/dts/imx28-pinfunc.h and arch/arm/boot/dts/imx23-pinfunc.h.
+The definitions for the padconfig properties can be found in
+arch/arm/boot/dts/mxs-pinfunc.h.
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,vf610-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,vf610-pinctrl.txt
new file mode 100644
index 000000000..ddcdeb697
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,vf610-pinctrl.txt
@@ -0,0 +1,41 @@
+Freescale Vybrid VF610 IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,vf610-iomuxc"
+- fsl,pins: two integers array, represents a group of pins mux and config
+  setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is
+  a pin working on a specific function, CONFIG is the pad setting value
+  such as pull-up, speed, ode for this pin. Please refer to Vybrid VF610
+  datasheet for the valid pad config settings.
+
+CONFIG bits definition:
+PAD_CTL_SPEED_LOW		(1 << 12)
+PAD_CTL_SPEED_MED		(2 << 12)
+PAD_CTL_SPEED_HIGH		(3 << 12)
+PAD_CTL_SRE_FAST		(1 << 11)
+PAD_CTL_SRE_SLOW		(0 << 11)
+PAD_CTL_ODE			(1 << 10)
+PAD_CTL_HYS			(1 << 9)
+PAD_CTL_DSE_DISABLE		(0 << 6)
+PAD_CTL_DSE_150ohm		(1 << 6)
+PAD_CTL_DSE_75ohm		(2 << 6)
+PAD_CTL_DSE_50ohm		(3 << 6)
+PAD_CTL_DSE_37ohm		(4 << 6)
+PAD_CTL_DSE_30ohm		(5 << 6)
+PAD_CTL_DSE_25ohm		(6 << 6)
+PAD_CTL_DSE_20ohm		(7 << 6)
+PAD_CTL_PUS_100K_DOWN		(0 << 4)
+PAD_CTL_PUS_47K_UP		(1 << 4)
+PAD_CTL_PUS_100K_UP		(2 << 4)
+PAD_CTL_PUS_22K_UP		(3 << 4)
+PAD_CTL_PKE			(1 << 3)
+PAD_CTL_PUE			(1 << 2)
+PAD_CTL_OBE_ENABLE		(1 << 1)
+PAD_CTL_IBE_ENABLE		(1 << 0)
+PAD_CTL_OBE_IBE_ENABLE		(3 << 0)
+
+Please refer to vf610-pinfunc.h in device tree source folder
+for all available PIN_FUNC_ID for Vybrid VF610.
diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt
new file mode 100644
index 000000000..51b943cc9
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt
@@ -0,0 +1,127 @@
+ImgTec TZ1090 PDC pin controller
+
+Required properties:
+- compatible: "img,tz1090-pdc-pinctrl"
+- reg: Should contain the register physical address and length of the
+  SOC_GPIO_CONTROL registers in the PDC register region.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+TZ1090-PDC's pin configuration nodes act as a container for an arbitrary number
+of subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function. For this reason, even seemingly boolean
+values are actually tristates in this binding: unspecified, off, or on.
+Unspecified is represented as an absent property, and off/on are represented as
+integer values 0 and 1.
+
+Required subnode-properties:
+- tz1090,pins : An array of strings. Each string contains the name of a pin or
+  group. Valid values for these names are listed below.
+
+Optional subnode-properties:
+- tz1090,function: A string containing the name of the function to mux to the
+  pin or group. Valid values for function names are listed below, including
+  which pingroups can be muxed to them.
+- supported generic pinconfig properties (for further details see
+  Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt):
+  - bias-disable
+  - bias-high-impedance
+  - bias-bus-hold
+  - bias-pull-up
+  - bias-pull-down
+  - input-schmitt-enable
+  - input-schmitt-disable
+  - drive-strength: Integer, control drive strength of pins in mA.
+      2: 2mA
+      4: 4mA
+      8: 8mA
+      12: 12mA
+  - low-power-enable: Flag, power-on-start weak pull-down for invalid power.
+  - low-power-disable: Flag, power-on-start weak pull-down disabled.
+
+Note that many of these properties are only valid for certain specific pins
+or groups. See the TZ1090 TRM for complete details regarding which groups
+support which functionality. The Linux pinctrl driver may also be a useful
+reference.
+
+Valid values for pin and group names are:
+
+  pins:
+
+    These all support bias-high-impediance, bias-pull-up, bias-pull-down, and
+    bias-bus-hold (which can also be provided to any of the groups below to set
+    it for all gpio pins in that group).
+
+    gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data, ext_power.
+
+  mux groups:
+
+    These all support function.
+
+    gpio0
+        pins:       gpio0.
+        function:   ir_mod_stable_out.
+    gpio1
+        pins:       gpio1.
+        function:   ir_mod_power_out.
+
+  drive groups:
+
+    These support input-schmitt-enable, input-schmitt-disable,
+    drive-strength, low-power-enable, and low-power-disable.
+
+    pdc
+        pins:   gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data,
+                ext_power.
+
+Example:
+
+	pinctrl_pdc: pinctrl@02006500 {
+		#gpio-range-cells = <3>;
+		compatible = "img,tz1090-pdc-pinctrl";
+		reg = <0x02006500 0x100>;
+	};
+
+Example board file extracts:
+
+	&pinctrl_pdc {
+		pinctrl-names = "default";
+		pinctrl-0 = <&syswake_default>;
+
+		syswake_default: syswakes {
+			syswake_cfg {
+				tz1090,pins =	"sys_wake0",
+						"sys_wake1",
+						"sys_wake2";
+				pull-up;
+			};
+		};
+		irmod_default: irmod {
+			gpio0_cfg {
+				tz1090,pins =	"gpio0";
+				tz1090,function = "ir_mod_stable_out";
+			};
+			gpio1_cfg {
+				tz1090,pins =	"gpio1";
+				tz1090,function = "ir_mod_power_out";
+			};
+		};
+	};
+
+	ir: ir@02006200 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&irmod_default>;
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt
new file mode 100644
index 000000000..509faa87a
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt
@@ -0,0 +1,227 @@
+ImgTec TZ1090 pin controller
+
+Required properties:
+- compatible: "img,tz1090-pinctrl"
+- reg: Should contain the register physical address and length of the pad
+  configuration registers (CR_PADS_* and CR_IF_CTL0).
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+TZ1090's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function. For this reason, even seemingly boolean
+values are actually tristates in this binding: unspecified, off, or on.
+Unspecified is represented as an absent property, and off/on are represented as
+integer values 0 and 1.
+
+Required subnode-properties:
+- tz1090,pins : An array of strings. Each string contains the name of a pin or
+  group. Valid values for these names are listed below.
+
+Optional subnode-properties:
+- tz1090,function: A string containing the name of the function to mux to the
+  pin or group. Valid values for function names are listed below, including
+  which pingroups can be muxed to them.
+- supported generic pinconfig properties (for further details see
+  Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt):
+  - bias-disable
+  - bias-high-impedance
+  - bias-bus-hold
+  - bias-pull-up
+  - bias-pull-down
+  - input-schmitt-enable
+  - input-schmitt-disable
+  - drive-strength: Integer, control drive strength of pins in mA.
+      2: 2mA
+      4: 4mA
+      8: 8mA
+      12: 12mA
+
+
+Note that many of these properties are only valid for certain specific pins
+or groups. See the TZ1090 TRM for complete details regarding which groups
+support which functionality. The Linux pinctrl driver may also be a useful
+reference.
+
+Valid values for pin and group names are:
+
+  gpio pins:
+
+    These all support bias-high-impediance, bias-pull-up, bias-pull-down, and
+    bias-bus-hold (which can also be provided to any of the groups below to set
+    it for all pins in that group).
+
+    They also all support the some form of muxing. Any pins which are contained
+    in one of the mux groups (see below) can be muxed only to the functions
+    supported by the mux group. All other pins can be muxed to the "perip"
+    function which enables them with their intended peripheral.
+
+    Different pins in the same mux group cannot be muxed to different functions,
+    however it is possible to mux only a subset of the pins in a mux group to a
+    particular function and leave the remaining pins unmuxed. This is useful if
+    the board connects certain pins in a group to other devices to be controlled
+    by GPIO, and you don't want the usual peripheral to have any control of the
+    pin.
+
+    ant_sel0, ant_sel1, gain0, gain1, gain2, gain3, gain4, gain5, gain6, gain7,
+    i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, i2s_lrclk_out,
+    i2s_mclk, pa_on, pdm_a, pdm_b, pdm_c, pdm_d, pll_on, rx_hp, rx_on,
+    scb0_sclk, scb0_sdat, scb1_sclk, scb1_sdat, scb2_sclk, scb2_sdat, sdh_cd,
+    sdh_clk_in, sdh_wp, sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
+    spi0_cs0, spi0_cs1, spi0_cs2, spi0_din, spi0_dout, spi0_mclk, spi1_cs0,
+    spi1_cs1, spi1_cs2, spi1_din, spi1_dout, spi1_mclk, tft_blank_ls, tft_blue0,
+    tft_blue1, tft_blue2, tft_blue3, tft_blue4, tft_blue5, tft_blue6, tft_blue7,
+    tft_green0, tft_green1, tft_green2, tft_green3, tft_green4, tft_green5,
+    tft_green6, tft_green7, tft_hsync_nr, tft_panelclk, tft_pwrsave, tft_red0,
+    tft_red1, tft_red2, tft_red3, tft_red4, tft_red5, tft_red6, tft_red7,
+    tft_vd12acb, tft_vdden_gd, tft_vsync_ns, tx_on, uart0_cts, uart0_rts,
+    uart0_rxd, uart0_txd, uart1_rxd, uart1_txd.
+
+        bias-high-impediance:  supported.
+        bias-pull-up:          supported.
+        bias-pull-down:        supported.
+        bias-bus-hold:         supported.
+        function:              perip or those supported by pin's mux group.
+
+  other pins:
+
+    These other pins are part of various pin groups below, but can't be
+    controlled as GPIOs. They do however support bias-high-impediance,
+    bias-pull-up, bias-pull-down, and bias-bus-hold (which can also be provided
+    to any of the groups below to set it for all pins in that group).
+
+    clk_out0, clk_out1, tck, tdi, tdo, tms, trst.
+
+        bias-high-impediance:  supported.
+        bias-pull-up:          supported.
+        bias-pull-down:        supported.
+        bias-bus-hold:         supported.
+
+  mux groups:
+
+    These all support function, and some support drive configs.
+
+    afe
+        pins:                  tx_on, rx_on, pll_on, pa_on, rx_hp, ant_sel0,
+                               ant_sel1, gain0, gain1, gain2, gain3, gain4,
+                               gain5, gain6, gain7.
+        function:              afe, ts_out_0.
+        input-schmitt-enable:  supported.
+        input-schmitt-disable: supported.
+        drive-strength:        supported.
+    pdm_d
+        pins:                  pdm_d.
+        function:              pdm_dac, usb_vbus.
+    sdh
+        pins:                  sdh_cd, sdh_wp, sdh_clk_in.
+        function:              sdh, sdio.
+    sdio
+        pins:                  sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2,
+                               sdio_d3.
+        function:              sdio, sdh.
+    spi1_cs2
+        pins:                  spi1_cs2.
+        function:              spi1_cs2, usb_vbus.
+    tft
+        pins:                  tft_red0, tft_red1, tft_red2, tft_red3,
+                               tft_red4, tft_red5, tft_red6, tft_red7,
+                               tft_green0, tft_green1, tft_green2, tft_green3,
+                               tft_green4, tft_green5, tft_green6, tft_green7,
+                               tft_blue0, tft_blue1, tft_blue2, tft_blue3,
+                               tft_blue4, tft_blue5, tft_blue6, tft_blue7,
+                               tft_vdden_gd, tft_panelclk, tft_blank_ls,
+                               tft_vsync_ns, tft_hsync_nr, tft_vd12acb,
+                               tft_pwrsave.
+        function:              tft, ext_dac, not_iqadc_stb, iqdac_stb, ts_out_1,
+                               lcd_trace, phy_ringosc.
+        input-schmitt-enable:  supported.
+        input-schmitt-disable: supported.
+        drive-strength:        supported.
+
+  drive groups:
+
+    These all support input-schmitt-enable, input-schmitt-disable,
+    and drive-strength.
+
+    jtag
+        pins:   tck, trst, tdi, tdo, tms.
+    scb1
+        pins:   scb1_sdat, scb1_sclk.
+    scb2
+        pins:   scb2_sdat, scb2_sclk.
+    spi0
+        pins:   spi0_mclk, spi0_cs0, spi0_cs1, spi0_cs2, spi0_dout, spi0_din.
+    spi1
+        pins:   spi1_mclk, spi1_cs0, spi1_cs1, spi1_cs2, spi1_dout, spi1_din.
+    uart
+        pins:   uart0_txd, uart0_rxd, uart0_rts, uart0_cts,
+                uart1_txd, uart1_rxd.
+    drive_i2s
+        pins:   clk_out1, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
+                i2s_lrclk_out, i2s_bclk_out, i2s_mclk.
+    drive_pdm
+        pins:   clk_out0, pdm_b, pdm_a.
+    drive_scb0
+        pins:   scb0_sclk, scb0_sdat, pdm_d, pdm_c.
+    drive_sdio
+        pins:   sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3,
+                sdh_wp, sdh_cd, sdh_clk_in.
+
+  convenience groups:
+
+    These are just convenient groupings of pins and don't support any drive
+    configs.
+
+    uart0
+        pins:   uart0_cts, uart0_rts, uart0_rxd, uart0_txd.
+    uart1
+        pins:   uart1_rxd, uart1_txd.
+    scb0
+        pins:   scb0_sclk, scb0_sdat.
+    i2s
+        pins:   i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2,
+                i2s_lrclk_out, i2s_mclk.
+
+Example:
+
+	pinctrl: pinctrl@02005800 {
+		#gpio-range-cells = <3>;
+		compatible = "img,tz1090-pinctrl";
+		reg = <0x02005800 0xe4>;
+	};
+
+Example board file extract:
+
+	&pinctrl {
+		uart0_default: uart0 {
+			uart0_cfg {
+				tz1090,pins =	"uart0_rxd",
+						"uart0_txd";
+				tz1090,function = "perip";
+			};
+		};
+		tft_default: tft {
+			tft_cfg {
+				tz1090,pins =	"tft";
+				tz1090,function = "tft";
+			};
+		};
+	};
+
+	uart@02004b00 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart0_default>;
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt
new file mode 100644
index 000000000..ac4da9fe0
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/lantiq,falcon-pinumx.txt
@@ -0,0 +1,83 @@
+Lantiq FALCON pinmux controller
+
+Required properties:
+- compatible: "lantiq,pinctrl-falcon"
+- reg: Should contain the physical address and length of the gpio/pinmux
+  register range
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Lantiq's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those group(s), and two pin configuration parameters:
+pull-up and open-drain
+
+The name of each subnode is not important as long as it is unique; all subnodes
+should be enumerated and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+We support 2 types of nodes.
+
+Definition of mux function groups:
+
+Required subnode-properties:
+- lantiq,groups : An array of strings. Each string contains the name of a group.
+  Valid values for these names are listed below.
+- lantiq,function: A string containing the name of the function to mux to the
+  group. Valid values for function names are listed below.
+
+Valid values for group and function names:
+
+  mux groups:
+    por, ntr, ntr8k, hrst, mdio, bootled, asc0, spi, spi cs0, spi cs1, i2c,
+    jtag, slic, pcm, asc1
+
+  functions:
+    rst, ntr, mdio, led, asc, spi, i2c, jtag, slic, pcm
+
+
+Definition of pin configurations:
+
+Required subnode-properties:
+- lantiq,pins : An array of strings. Each string contains the name of a pin.
+  Valid values for these names are listed below.
+
+Optional subnode-properties:
+- lantiq,pull: Integer, representing the pull-down/up to apply to the pin.
+    0: none, 1: down
+- lantiq,drive-current: Boolean, enables drive-current
+- lantiq,slew-rate: Boolean, enables slew-rate
+
+Example:
+	pinmux0 {
+		compatible = "lantiq,pinctrl-falcon";
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			asc0 {
+				lantiq,groups = "asc0";
+				lantiq,function = "asc";
+			};
+			ntr {
+				lantiq,groups = "ntr8k";
+				lantiq,function = "ntr";
+			};
+			i2c {
+				lantiq,groups = "i2c";
+				lantiq,function = "i2c";
+			};
+			hrst {
+				lantiq,groups = "hrst";
+				lantiq,function = "rst";
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt
new file mode 100644
index 000000000..e89b46775
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/lantiq,xway-pinumx.txt
@@ -0,0 +1,97 @@
+Lantiq XWAY pinmux controller
+
+Required properties:
+- compatible: "lantiq,pinctrl-xway" or "lantiq,pinctrl-xr9"
+- reg: Should contain the physical address and length of the gpio/pinmux
+  register range
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Lantiq's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those group(s), and two pin configuration parameters:
+pull-up and open-drain
+
+The name of each subnode is not important as long as it is unique; all subnodes
+should be enumerated and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+We support 2 types of nodes.
+
+Definition of mux function groups:
+
+Required subnode-properties:
+- lantiq,groups : An array of strings. Each string contains the name of a group.
+  Valid values for these names are listed below.
+- lantiq,function: A string containing the name of the function to mux to the
+  group. Valid values for function names are listed below.
+
+Valid values for group and function names:
+
+  mux groups:
+    exin0, exin1, exin2, jtag, ebu a23, ebu a24, ebu a25, ebu clk, ebu cs1,
+    ebu wait, nand ale, nand cs1, nand cle, spi, spi_cs1, spi_cs2, spi_cs3,
+    spi_cs4, spi_cs5, spi_cs6, asc0, asc0 cts rts, stp, nmi , gpt1, gpt2,
+    gpt3, clkout0, clkout1, clkout2, clkout3, gnt1, gnt2, gnt3, req1, req2,
+    req3
+
+  additional mux groups (XR9 only):
+    mdio, nand rdy, nand rd, exin3, exin4, gnt4, req4
+
+  functions:
+    spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu, mdio
+
+
+
+Definition of pin configurations:
+
+Required subnode-properties:
+- lantiq,pins : An array of strings. Each string contains the name of a pin.
+  Valid values for these names are listed below.
+
+Optional subnode-properties:
+- lantiq,pull: Integer, representing the pull-down/up to apply to the pin.
+    0: none, 1: down, 2: up.
+- lantiq,open-drain: Boolean, enables open-drain on the defined pin.
+
+Valid values for XWAY pin names:
+  Pinconf pins can be referenced via the names io0-io31.
+
+Valid values for XR9 pin names:
+  Pinconf pins can be referenced via the names io0-io55.
+
+Example:
+	gpio: pinmux@E100B10 {
+		compatible = "lantiq,pinctrl-xway";
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0xE100B10 0xA0>;
+
+		state_default: pinmux {
+			stp {
+				lantiq,groups = "stp";
+				lantiq,function = "stp";
+			};
+			pci {
+				lantiq,groups = "gnt1";
+				lantiq,function = "pci";
+			};
+			conf_out {
+				lantiq,pins = "io4", "io5", "io6"; /* stp */
+				lantiq,open-drain;
+				lantiq,pull = <0>;
+			};
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt
new file mode 100644
index 000000000..e357b0208
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-370-pinctrl.txt
@@ -0,0 +1,96 @@
+* Marvell Armada 370 SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,88f6710-pinctrl"
+- reg: register specifier of MPP registers
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, uart0(rxd)
+mpp1          1        gpo, uart0(txd)
+mpp2          2        gpio, i2c0(sck), uart0(txd)
+mpp3          3        gpio, i2c0(sda), uart0(rxd)
+mpp4          4        gpio, cpu_pd(vdd)
+mpp5          5        gpo, ge0(txclko), uart1(txd), spi1(clk), audio(mclk)
+mpp6          6        gpio, ge0(txd0), sata0(prsnt), tdm(rst), audio(sdo)
+mpp7          7        gpo, ge0(txd1), tdm(tdx), audio(lrclk)
+mpp8          8        gpio, ge0(txd2), uart0(rts), tdm(drx), audio(bclk)
+mpp9          9        gpo, ge0(txd3), uart1(txd), sd0(clk), audio(spdifo)
+mpp10         10       gpio, ge0(txctl), uart0(cts), tdm(fsync), audio(sdi)
+mpp11         11       gpio, ge0(rxd0), uart1(rxd), sd0(cmd), spi0(cs1),
+                       sata1(prsnt), spi1(cs1)
+mpp12         12       gpio, ge0(rxd1), i2c1(sda), sd0(d0), spi1(cs0),
+                       audio(spdifi)
+mpp13         13       gpio, ge0(rxd2), i2c1(sck), sd0(d1), tdm(pclk),
+                       audio(rmclk)
+mpp14         14       gpio, ge0(rxd3), pcie(clkreq0), sd0(d2), spi1(mosi),
+                       spi0(cs2)
+mpp15         15       gpio, ge0(rxctl), pcie(clkreq1), sd0(d3), spi1(miso),
+                       spi0(cs3)
+mpp16         16       gpio, ge0(rxclk), uart1(rxd), tdm(int), audio(extclk)
+mpp17         17       gpo, ge(mdc)
+mpp18         18       gpio, ge(mdio)
+mpp19         19       gpio, ge0(txclk), ge1(txclkout), tdm(pclk)
+mpp20         20       gpo, ge0(txd4), ge1(txd0)
+mpp21         21       gpo, ge0(txd5), ge1(txd1), uart1(txd)
+mpp22         22       gpo, ge0(txd6), ge1(txd2), uart0(rts)
+mpp23         23       gpo, ge0(txd7), ge1(txd3), spi1(mosi)
+mpp24         24       gpio, ge0(col), ge1(txctl), spi1(cs0)
+mpp25         25       gpio, ge0(rxerr), ge1(rxd0), uart1(rxd)
+mpp26         26       gpio, ge0(crs), ge1(rxd1), spi1(miso)
+mpp27         27       gpio, ge0(rxd4), ge1(rxd2), uart0(cts)
+mpp28         28       gpio, ge0(rxd5), ge1(rxd3)
+mpp29         29       gpio, ge0(rxd6), ge1(rxctl), i2c1(sda)
+mpp30         30       gpio, ge0(rxd7), ge1(rxclk), i2c1(sck)
+mpp31         31       gpio, tclk, ge0(txerr)
+mpp32         32       gpio, spi0(cs0)
+mpp33         33       gpio, dev(bootcs), spi0(cs0)
+mpp34         34       gpo, dev(wen0), spi0(mosi)
+mpp35         35       gpo, dev(oen), spi0(sck)
+mpp36         36       gpo, dev(a1), spi0(miso)
+mpp37         37       gpo, dev(a0), sata0(prsnt)
+mpp38         38       gpio, dev(ready), uart1(cts), uart0(cts)
+mpp39         39       gpo, dev(ad0), audio(spdifo)
+mpp40         40       gpio, dev(ad1), uart1(rts), uart0(rts)
+mpp41         41       gpio, dev(ad2), uart1(rxd)
+mpp42         42       gpo, dev(ad3), uart1(txd)
+mpp43         43       gpo, dev(ad4), audio(bclk)
+mpp44         44       gpo, dev(ad5), audio(mclk)
+mpp45         45       gpo, dev(ad6), audio(lrclk)
+mpp46         46       gpo, dev(ad7), audio(sdo)
+mpp47         47       gpo, dev(ad8), sd0(clk), audio(spdifo)
+mpp48         48       gpio, dev(ad9), uart0(rts), sd0(cmd), sata1(prsnt),
+                       spi0(cs1)
+mpp49         49       gpio, dev(ad10), pcie(clkreq1), sd0(d0), spi1(cs0),
+                       audio(spdifi)
+mpp50         50       gpio, dev(ad11), uart0(cts), sd0(d1), spi1(miso),
+                       audio(rmclk)
+mpp51         51       gpio, dev(ad12), i2c1(sda), sd0(d2), spi1(mosi)
+mpp52         52       gpio, dev(ad13), i2c1(sck), sd0(d3), spi1(sck)
+mpp53         53       gpio, dev(ad14), sd0(clk), tdm(pclk), spi0(cs2),
+                       pcie(clkreq1)
+mpp54         54       gpo, dev(ad15), tdm(dtx)
+mpp55         55       gpio, dev(cs1), uart1(txd), tdm(rst), sata1(prsnt),
+                       sata0(prsnt)
+mpp56         56       gpio, dev(cs2), uart1(cts), uart0(cts), spi0(cs3),
+                       pcie(clkreq0), spi1(cs1)
+mpp57         57       gpio, dev(cs3), uart1(rxd), tdm(fsync), sata0(prsnt),
+                       audio(sdo)
+mpp58         58       gpio, dev(cs0), uart1(rts), tdm(int), audio(extclk),
+                       uart0(rts)
+mpp59         59       gpo, dev(ale0), uart1(rts), uart0(rts), audio(bclk)
+mpp60         60       gpio, dev(ale1), uart1(rxd), sata0(prsnt), pcie(rst-out),
+                       audio(sdi)
+mpp61         61       gpo, dev(wen1), uart1(txd), audio(rclk)
+mpp62         62       gpio, dev(a2), uart1(cts), tdm(drx), pcie(clkreq0),
+                       audio(mclk), uart0(cts)
+mpp63         63       gpo, spi0(sck), tclk
+mpp64         64       gpio, spi0(miso), spi0(cs1)
+mpp65         65       gpio, spi0(mosi), spi0(cs2)
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-375-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-375-pinctrl.txt
new file mode 100644
index 000000000..bedbe42c8
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-375-pinctrl.txt
@@ -0,0 +1,82 @@
+* Marvell Armada 375 SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,88f6720-pinctrl"
+- reg: register specifier of MPP registers
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, dev(ad2), spi0(cs1), spi1(cs1)
+mpp1          1        gpio, dev(ad3), spi0(mosi), spi1(mosi)
+mpp2          2        gpio, dev(ad4), ptp(eventreq), led(c0), audio(sdi)
+mpp3          3        gpio, dev(ad5), ptp(triggen), led(p3), audio(mclk)
+mpp4          4        gpio, dev(ad6), spi0(miso), spi1(miso)
+mpp5          5        gpio, dev(ad7), spi0(cs2), spi1(cs2)
+mpp6          6        gpio, dev(ad0), led(p1), audio(rclk)
+mpp7          7        gpio, dev(ad1), ptp(clk), led(p2), audio(extclk)
+mpp8          8        gpio, dev (bootcs), spi0(cs0), spi1(cs0)
+mpp9          9        gpio, spi0(sck), spi1(sck), nand(we)
+mpp10        10        gpio, dram(vttctrl), led(c1), nand(re)
+mpp11        11        gpio, dev(a0), led(c2), audio(sdo)
+mpp12        12        gpio, dev(a1), audio(bclk)
+mpp13        13        gpio, dev(readyn), pcie0(rstoutn), pcie1(rstoutn)
+mpp14        14        gpio, i2c0(sda), uart1(txd)
+mpp15        15        gpio, i2c0(sck), uart1(rxd)
+mpp16        16        gpio, uart0(txd)
+mpp17        17        gpio, uart0(rxd)
+mpp18        18        gpio, tdm(intn)
+mpp19        19        gpio, tdm(rstn)
+mpp20        20        gpio, tdm(pclk)
+mpp21        21        gpio, tdm(fsync)
+mpp22        22        gpio, tdm(drx)
+mpp23        23        gpio, tdm(dtx)
+mpp24        24        gpio, led(p0), ge1(rxd0), sd(cmd), uart0(rts)
+mpp25        25        gpio, led(p2), ge1(rxd1), sd(d0), uart0(cts)
+mpp26        26        gpio, pcie0(clkreq), ge1(rxd2), sd(d2), uart1(rts)
+mpp27        27        gpio, pcie1(clkreq), ge1(rxd3), sd(d1), uart1(cts)
+mpp28        28        gpio, led(p3), ge1(txctl), sd(clk)
+mpp29        29        gpio, pcie1(clkreq), ge1(rxclk), sd(d3)
+mpp30        30        gpio, ge1(txd0), spi1(cs0)
+mpp31        31        gpio, ge1(txd1), spi1(mosi)
+mpp32        32        gpio, ge1(txd2), spi1(sck), ptp(triggen)
+mpp33        33        gpio, ge1(txd3), spi1(miso)
+mpp34        34        gpio, ge1(txclkout), spi1(sck)
+mpp35        35        gpio, ge1(rxctl), spi1(cs1), spi0(cs2)
+mpp36        36        gpio, pcie0(clkreq)
+mpp37        37        gpio, pcie0(clkreq), tdm(intn), ge(mdc)
+mpp38        38        gpio, pcie1(clkreq), ge(mdio)
+mpp39        39        gpio, ref(clkout)
+mpp40        40        gpio, uart1(txd)
+mpp41        41        gpio, uart1(rxd)
+mpp42        42        gpio, spi1(cs2), led(c0)
+mpp43        43        gpio, sata0(prsnt), dram(vttctrl)
+mpp44        44        gpio, sata0(prsnt)
+mpp45        45        gpio, spi0(cs2), pcie0(rstoutn)
+mpp46        46        gpio, led(p0), ge0(txd0), ge1(txd0)
+mpp47        47        gpio, led(p1), ge0(txd1), ge1(txd1)
+mpp48        48        gpio, led(p2), ge0(txd2), ge1(txd2)
+mpp49        49        gpio, led(p3), ge0(txd3), ge1(txd3)
+mpp50        50        gpio, led(c0), ge0(rxd0), ge1(rxd0)
+mpp51        51        gpio, led(c1), ge0(rxd1), ge1(rxd1)
+mpp52        52        gpio, led(c2), ge0(rxd2), ge1(rxd2)
+mpp53        53        gpio, pcie1(rstoutn), ge0(rxd3), ge1(rxd3)
+mpp54        54        gpio, pcie0(rstoutn), ge0(rxctl), ge1(rxctl)
+mpp55        55        gpio, ge0(rxclk), ge1(rxclk)
+mpp56        56        gpio, ge0(txclkout), ge1(txclkout)
+mpp57        57        gpio, ge0(txctl), ge1(txctl)
+mpp58        58        gpio, led(c0)
+mpp59        59        gpio, led(c1)
+mpp60        60        gpio, uart1(txd), led(c2)
+mpp61        61        gpio, i2c1(sda), uart1(rxd), spi1(cs2), led(p0)
+mpp62        62        gpio, i2c1(sck), led(p1)
+mpp63        63        gpio, ptp(triggen), led(p2)
+mpp64        64        gpio, dram(vttctrl), led(p3)
+mpp65        65        gpio, sata1(prsnt)
+mpp66        66        gpio, ptp(eventreq), spi1(cs3)
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-38x-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-38x-pinctrl.txt
new file mode 100644
index 000000000..4ac138aaa
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-38x-pinctrl.txt
@@ -0,0 +1,80 @@
+* Marvell Armada 380/385 SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,88f6810-pinctrl", "marvell,88f6820-pinctrl" or
+  "marvell,88f6828-pinctrl" depending on the specific variant of the
+  SoC being used.
+- reg: register specifier of MPP registers
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, ua0(rxd)
+mpp1          1        gpio, ua0(txd)
+mpp2          2        gpio, i2c0(sck)
+mpp3          3        gpio, i2c0(sda)
+mpp4          4        gpio, ge(mdc), ua1(txd), ua0(rts)
+mpp5          5        gpio, ge(mdio), ua1(rxd), ua0(cts)
+mpp6          6        gpio, ge0(txclkout), ge0(crs), dev(cs3)
+mpp7          7        gpio, ge0(txd0), dev(ad9)
+mpp8          8        gpio, ge0(txd1), dev(ad10)
+mpp9          9        gpio, ge0(txd2), dev(ad11)
+mpp10         10       gpio, ge0(txd3), dev(ad12)
+mpp11         11       gpio, ge0(txctl), dev(ad13)
+mpp12         12       gpio, ge0(rxd0), pcie0(rstout), spi0(cs1), dev(ad14), pcie3(clkreq)
+mpp13         13       gpio, ge0(rxd1), pcie0(clkreq), pcie1(clkreq) [1], spi0(cs2), dev(ad15), pcie2(clkreq)
+mpp14         14       gpio, ge0(rxd2), ptp(clk), m(vtt_ctrl), spi0(cs3), dev(wen1), pcie3(clkreq)
+mpp15         15       gpio, ge0(rxd3), ge(mdc slave), pcie0(rstout), spi0(mosi)
+mpp16         16       gpio, ge0(rxctl), ge(mdio slave), m(decc_err), spi0(miso), pcie0(clkreq), pcie1(clkreq) [1]
+mpp17         17       gpio, ge0(rxclk), ptp(clk), ua1(rxd), spi0(sck), sata1(prsnt)
+mpp18         18       gpio, ge0(rxerr), ptp(trig_gen), ua1(txd), spi0(cs0)
+mpp19         19       gpio, ge0(col), ptp(event_req), ge0(txerr), sata1(prsnt), ua0(cts)
+mpp20         20       gpio, ge0(txclk), ptp(clk), sata0(prsnt), ua0(rts)
+mpp21         21       gpio, spi0(cs1), ge1(rxd0), sata0(prsnt), sd0(cmd), dev(bootcs)
+mpp22         22       gpio, spi0(mosi), dev(ad0)
+mpp23         23       gpio, spi0(sck), dev(ad2)
+mpp24         24       gpio, spi0(miso), ua0(cts), ua1(rxd), sd0(d4), dev(ready)
+mpp25         25       gpio, spi0(cs0), ua0(rts), ua1(txd), sd0(d5), dev(cs0)
+mpp26         26       gpio, spi0(cs2), i2c1(sck), sd0(d6), dev(cs1)
+mpp27         27       gpio, spi0(cs3), ge1(txclkout), i2c1(sda), sd0(d7), dev(cs2)
+mpp28         28       gpio, ge1(txd0), sd0(clk), dev(ad5)
+mpp29         29       gpio, ge1(txd1), dev(ale0)
+mpp30         30       gpio, ge1(txd2), dev(oen)
+mpp31         31       gpio, ge1(txd3), dev(ale1)
+mpp32         32       gpio, ge1(txctl), dev(wen0)
+mpp33         33       gpio, m(decc_err), dev(ad3)
+mpp34         34       gpio, dev(ad1)
+mpp35         35       gpio, ref(clk_out1), dev(a1)
+mpp36         36       gpio, ptp(trig_gen), dev(a0)
+mpp37         37       gpio, ptp(clk), ge1(rxclk), sd0(d3), dev(ad8)
+mpp38         38       gpio, ptp(event_req), ge1(rxd1), ref(clk_out0), sd0(d0), dev(ad4)
+mpp39         39       gpio, i2c1(sck), ge1(rxd2), ua0(cts), sd0(d1), dev(a2)
+mpp40         40       gpio, i2c1(sda), ge1(rxd3), ua0(rts), sd0(d2), dev(ad6)
+mpp41         41       gpio, ua1(rxd), ge1(rxctl), ua0(cts), spi1(cs3), dev(burst/last)
+mpp42         42       gpio, ua1(txd), ua0(rts), dev(ad7)
+mpp43         43       gpio, pcie0(clkreq), m(vtt_ctrl), m(decc_err), spi1(cs2), dev(clkout)
+mpp44         44       gpio, sata0(prsnt), sata1(prsnt), sata2(prsnt) [2], sata3(prsnt) [3]
+mpp45         45       gpio, ref(clk_out0), pcie0(rstout)
+mpp46         46       gpio, ref(clk_out1), pcie0(rstout)
+mpp47         47       gpio, sata0(prsnt), sata1(prsnt), sata2(prsnt) [2], sata3(prsnt) [2]
+mpp48         48       gpio, sata0(prsnt), m(vtt_ctrl), tdm2c(pclk), audio(mclk), sd0(d4), pcie0(clkreq)
+mpp49         49       gpio, sata2(prsnt) [2], sata3(prsnt) [2], tdm2c(fsync), audio(lrclk), sd0(d5), pcie1(clkreq)
+mpp50         50       gpio, pcie0(rstout), tdm2c(drx), audio(extclk), sd0(cmd)
+mpp51         51       gpio, tdm2c(dtx), audio(sdo), m(decc_err)
+mpp52         52       gpio, pcie0(rstout), tdm2c(intn), audio(sdi), sd0(d6)
+mpp53         53       gpio, sata1(prsnt), sata0(prsnt), tdm2c(rstn), audio(bclk), sd0(d7)
+mpp54         54       gpio, sata0(prsnt), sata1(prsnt), pcie0(rstout), ge0(txerr), sd0(d3)
+mpp55         55       gpio, ua1(cts), ge(mdio), pcie1(clkreq) [1], spi1(cs1), sd0(d0)
+mpp56         56       gpio, ua1(rts), ge(mdc), m(decc_err), spi1(mosi)
+mpp57         57       gpio, spi1(sck), sd0(clk)
+mpp58         58       gpio, pcie1(clkreq) [1], i2c1(sck), pcie2(clkreq), spi1(miso), sd0(d1)
+mpp59         59       gpio, pcie0(rstout), i2c1(sda), spi1(cs0), sd0(d2)
+
+[1]: only available on 88F6820 and 88F6828
+[2]: only available on 88F6828
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
new file mode 100644
index 000000000..5b1a9dc00
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
@@ -0,0 +1,78 @@
+* Marvell Armada 39x SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,88f6920-pinctrl", "marvell,88f6928-pinctrl"
+  depending on the specific variant of the SoC being used.
+- reg: register specifier of MPP registers
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+name    pins    functions
+================================================================================
+mpp0	0	gpio, ua0(rxd)
+mpp1	1	gpio, ua0(txd)
+mpp2	2	gpio, i2c0(sck)
+mpp3	3	gpio, i2c0(sda)
+mpp4	4	gpio, ua1(txd), ua0(rts), smi(mdc)
+mpp5	5	gpio, ua1(rxd), ua0(cts), smi(mdio)
+mpp6	6	gpio, dev(cs3), xsmi(mdio)
+mpp7	7	gpio, dev(ad9), xsmi(mdc)
+mpp8	8	gpio, dev(ad10), ptp(trig)
+mpp9	9	gpio, dev(ad11), ptp(clk)
+mpp10	10	gpio, dev(ad12), ptp(event)
+mpp11	11	gpio, dev(ad13), led(clk)
+mpp12	12	gpio, pcie0(rstout), dev(ad14), led(stb)
+mpp13	13	gpio, dev(ad15), led(data)
+mpp14	14	gpio, m(vtt), dev(wen1), ua1(txd)
+mpp15	15	gpio, pcie0(rstout), spi0(mosi), i2c1(sck)
+mpp16	16	gpio, m(decc), spi0(miso), i2c1(sda)
+mpp17	17	gpio, ua1(rxd), spi0(sck), smi(mdio)
+mpp18	18	gpio, ua1(txd), spi0(cs0), i2c2(sck)
+mpp19	19	gpio, sata1(present) [1], ua0(cts), ua1(rxd), i2c2(sda)
+mpp20	20	gpio, sata0(present) [1], ua0(rts), ua1(txd), smi(mdc)
+mpp21	21	gpio, spi0(cs1), sata0(present) [1], sd(cmd), dev(bootcs), ge(rxd0)
+mpp22	22	gpio, spi0(mosi), dev(ad0)
+mpp23	23	gpio, spi0(sck), dev(ad2)
+mpp24	24	gpio, spi0(miso), ua0(cts), ua1(rxd), sd(d4), dev(readyn)
+mpp25	25	gpio, spi0(cs0), ua0(rts), ua1(txd), sd(d5), dev(cs0)
+mpp26	26	gpio, spi0(cs2), i2c1(sck), sd(d6), dev(cs1)
+mpp27	27	gpio, spi0(cs3), i2c1(sda), sd(d7), dev(cs2), ge(txclkout)
+mpp28	28	gpio, sd(clk), dev(ad5), ge(txd0)
+mpp29	29	gpio, dev(ale0), ge(txd1)
+mpp30	30	gpio, dev(oen), ge(txd2)
+mpp31	31	gpio, dev(ale1), ge(txd3)
+mpp32	32	gpio, dev(wen0), ge(txctl)
+mpp33	33	gpio, m(decc), dev(ad3)
+mpp34	34	gpio, dev(ad1)
+mpp35	35	gpio, ref(clk), dev(a1)
+mpp36	36	gpio, dev(a0)
+mpp37	37	gpio, sd(d3), dev(ad8), ge(rxclk)
+mpp38	38	gpio, ref(clk), sd(d0), dev(ad4), ge(rxd1)
+mpp39	39	gpio, i2c1(sck), ua0(cts), sd(d1), dev(a2), ge(rxd2)
+mpp40	40	gpio, i2c1(sda), ua0(rts), sd(d2), dev(ad6), ge(rxd3)
+mpp41	41	gpio, ua1(rxd), ua0(cts), spi1(cs3), dev(burstn), nd(rbn0), ge(rxctl)
+mpp42	42	gpio, ua1(txd), ua0(rts), dev(ad7)
+mpp43	43	gpio, pcie0(clkreq), m(vtt), m(decc), spi1(cs2), dev(clkout), nd(rbn1)
+mpp44	44	gpio, sata0(present) [1], sata1(present) [1], led(clk)
+mpp45	45	gpio, ref(clk), pcie0(rstout), ua1(rxd)
+mpp46	46	gpio, ref(clk), pcie0(rstout), ua1(txd), led(stb)
+mpp47	47	gpio, sata0(present) [1], sata1(present) [1], led(data)
+mpp48	48	gpio, sata0(present) [1], m(vtt), tdm(pclk) [1], audio(mclk) [1], sd(d4), pcie0(clkreq), ua1(txd)
+mpp49	49	gpio, tdm(fsync) [1], audio(lrclk) [1], sd(d5), ua2(rxd)
+mpp50	50	gpio, pcie0(rstout), tdm(drx) [1], audio(extclk) [1], sd(cmd), ua2(rxd)
+mpp51	51	gpio, tdm(dtx) [1], audio(sdo) [1], m(decc), ua2(txd)
+mpp52	52	gpio, pcie0(rstout), tdm(intn) [1], audio(sdi) [1], sd(d6), i2c3(sck)
+mpp53	53	gpio, sata1(present) [1], sata0(present) [1], tdm(rstn) [1], audio(bclk) [1], sd(d7), i2c3(sda)
+mpp54	54	gpio, sata0(present) [1], sata1(present) [1], pcie0(rstout), sd(d3), ua3(txd)
+mpp55	55	gpio, ua1(cts), spi1(cs1), sd(d0), ua1(rxd), ua3(rxd)
+mpp56	56	gpio, ua1(rts), m(decc), spi1(mosi), ua1(txd)
+mpp57	57	gpio, spi1(sck), sd(clk), ua1(txd)
+mpp58	58	gpio, i2c1(sck), pcie2(clkreq), spi1(miso), sd(d1), ua1(rxd)
+mpp59	59	gpio, pcie0(rstout), i2c1(sda), spi1(cs0), sd(d2)
+
+[1]: only available on 88F6928
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt
new file mode 100644
index 000000000..96e7744ca
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-xp-pinctrl.txt
@@ -0,0 +1,95 @@
+* Marvell Armada XP SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,mv78230-pinctrl", "marvell,mv78260-pinctrl",
+              "marvell,mv78460-pinctrl"
+- reg: register specifier of MPP registers
+
+This driver supports all Armada XP variants, i.e. mv78230, mv78260, and mv78460.
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+* Marvell Armada XP (all variants)
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, ge0(txclko), lcd(d0)
+mpp1          1        gpio, ge0(txd0), lcd(d1)
+mpp2          2        gpio, ge0(txd1), lcd(d2)
+mpp3          3        gpio, ge0(txd2), lcd(d3)
+mpp4          4        gpio, ge0(txd3), lcd(d4)
+mpp5          5        gpio, ge0(txctl), lcd(d5)
+mpp6          6        gpio, ge0(rxd0), lcd(d6)
+mpp7          7        gpio, ge0(rxd1), lcd(d7)
+mpp8          8        gpio, ge0(rxd2), lcd(d8)
+mpp9          9        gpio, ge0(rxd3), lcd(d9)
+mpp10         10       gpio, ge0(rxctl), lcd(d10)
+mpp11         11       gpio, ge0(rxclk), lcd(d11)
+mpp12         12       gpio, ge0(txd4), ge1(txd0), lcd(d12)
+mpp13         13       gpio, ge0(txd5), ge1(txd1), lcd(d13)
+mpp14         14       gpio, ge0(txd6), ge1(txd2), lcd(d15)
+mpp15         15       gpio, ge0(txd7), ge1(txd3), lcd(d16)
+mpp16         16       gpio, ge0(txd7), ge1(txd3), lcd(d16)
+mpp17         17       gpio, ge0(col), ge1(txctl), lcd(d17)
+mpp18         18       gpio, ge0(rxerr), ge1(rxd0), lcd(d18), ptp(trig)
+mpp19         19       gpio, ge0(crs), ge1(rxd1), lcd(d19), ptp(evreq)
+mpp20         20       gpio, ge0(rxd4), ge1(rxd2), lcd(d20), ptp(clk)
+mpp21         21       gpio, ge0(rxd5), ge1(rxd3), lcd(d21), mem(bat)
+mpp22         22       gpio, ge0(rxd6), ge1(rxctl), lcd(d22), sata0(prsnt)
+mpp23         23       gpio, ge0(rxd7), ge1(rxclk), lcd(d23), sata1(prsnt)
+mpp24         24       gpio, lcd(hsync), sata1(prsnt), tdm(rst)
+mpp25         25       gpio, lcd(vsync), sata0(prsnt), tdm(pclk)
+mpp26         26       gpio, lcd(clk), tdm(fsync)
+mpp27         27       gpio, lcd(e), tdm(dtx), ptp(trig)
+mpp28         28       gpio, lcd(pwm), tdm(drx), ptp(evreq)
+mpp29         29       gpio, lcd(ref-clk), tdm(int0), ptp(clk)
+mpp30         30       gpio, tdm(int1), sd0(clk)
+mpp31         31       gpio, tdm(int2), sd0(cmd)
+mpp32         32       gpio, tdm(int3), sd0(d0)
+mpp33         33       gpio, tdm(int4), sd0(d1), mem(bat)
+mpp34         34       gpio, tdm(int5), sd0(d2), sata0(prsnt)
+mpp35         35       gpio, tdm(int6), sd0(d3), sata1(prsnt)
+mpp36         36       gpio, spi(mosi)
+mpp37         37       gpio, spi(miso)
+mpp38         38       gpio, spi(sck)
+mpp39         39       gpio, spi(cs0)
+mpp40         40       gpio, spi(cs1), uart2(cts), lcd(vga-hsync), pcie(clkreq0)
+mpp41         41       gpio, spi(cs2), uart2(rts), lcd(vga-vsync), sata1(prsnt),
+                       pcie(clkreq1)
+mpp42         42       gpio, uart2(rxd), uart0(cts), tdm(int7), tdm-1(timer)
+mpp43         43       gpio, uart2(txd), uart0(rts), spi(cs3), pcie(rstout)
+mpp44         44       gpio, uart2(cts), uart3(rxd), spi(cs4), pcie(clkreq2),
+                       mem(bat)
+mpp45         45       gpio, uart2(rts), uart3(txd), spi(cs5), sata1(prsnt)
+mpp46         46       gpio, uart3(rts), uart1(rts), spi(cs6), sata0(prsnt)
+mpp47         47       gpio, uart3(cts), uart1(cts), spi(cs7), pcie(clkreq3),
+                       ref(clkout)
+mpp48         48       gpio, dev(clkout), dev(burst/last)
+
+* Marvell Armada XP (mv78260 and mv78460 only)
+
+name          pins     functions
+================================================================================
+mpp49         49       gpio, dev(we3)
+mpp50         50       gpio, dev(we2)
+mpp51         51       gpio, dev(ad16)
+mpp52         52       gpio, dev(ad17)
+mpp53         53       gpio, dev(ad18)
+mpp54         54       gpio, dev(ad19)
+mpp55         55       gpio, dev(ad20)
+mpp56         56       gpio, dev(ad21)
+mpp57         57       gpio, dev(ad22)
+mpp58         58       gpio, dev(ad23)
+mpp59         59       gpio, dev(ad24)
+mpp60         60       gpio, dev(ad25)
+mpp61         61       gpio, dev(ad26)
+mpp62         62       gpio, dev(ad27)
+mpp63         63       gpio, dev(ad28)
+mpp64         64       gpio, dev(ad29)
+mpp65         65       gpio, dev(ad30)
+mpp66         66       gpio, dev(ad31)
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt
new file mode 100644
index 000000000..cf52477cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt
@@ -0,0 +1,90 @@
+* Marvell Dove SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,dove-pinctrl"
+- clocks: (optional) phandle of pdma clock
+- reg: register specifiers of MPP, MPP4, and PMU MPP registers
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+Note: pmu* also allows for Power Management functions listed below
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, pmu, uart2(rts), sdio0(cd), lcd0(pwm), pmu*
+mpp1          1        gpio, pmu, uart2(cts), sdio0(wp), lcd1(pwm), pmu*
+mpp2          2        gpio, pmu, uart2(txd), sdio0(buspwr), sata(prsnt),
+                       uart1(rts), pmu*
+mpp3          3        gpio, pmu, uart2(rxd), sdio0(ledctrl), sata(act),
+                       uart1(cts), lcd-spi(cs1), pmu*
+mpp4          4        gpio, pmu, uart3(rts), sdio1(cd), spi1(miso), pmu*
+mpp5          5        gpio, pmu, uart3(cts), sdio1(wp), spi1(cs), pmu*
+mpp6          6        gpio, pmu, uart3(txd), sdio1(buspwr), spi1(mosi), pmu*
+mpp7          7        gpio, pmu, uart3(rxd), sdio1(ledctrl), spi1(sck), pmu*
+mpp8          8        gpio, pmu, watchdog(rstout), pmu*
+mpp9          9        gpio, pmu, pex1(clkreq), pmu*
+mpp10         10       gpio, pmu, ssp(sclk), pmu*
+mpp11         11       gpio, pmu, sata(prsnt), sata-1(act), sdio0(ledctrl),
+                       sdio1(ledctrl), pex0(clkreq), pmu*
+mpp12         12       gpio, pmu, uart2(rts), audio0(extclk), sdio1(cd),
+                       sata(act), pmu*
+mpp13         13       gpio, pmu, uart2(cts), audio1(extclk), sdio1(wp),
+                       ssp(extclk), pmu*
+mpp14         14       gpio, pmu, uart2(txd), sdio1(buspwr), ssp(rxd), pmu*
+mpp15         15       gpio, pmu, uart2(rxd), sdio1(ledctrl), ssp(sfrm), pmu*
+mpp16         16       gpio, uart3(rts), sdio0(cd), ac97(sdi1), lcd-spi(cs1)
+mpp17         17       gpio, uart3(cts), sdio0(wp), ac97(sdi2), twsi(sda),
+                       ac97-1(sysclko)
+mpp18         18       gpio, uart3(txd), sdio0(buspwr), ac97(sdi3), lcd0(pwm)
+mpp19         19       gpio, uart3(rxd), sdio0(ledctrl), twsi(sck)
+mpp20         20       gpio, sdio0(cd), sdio1(cd), spi1(miso), lcd-spi(miso),
+                       ac97(sysclko)
+mpp21         21       gpio, sdio0(wp), sdio1(wp), spi1(cs), lcd-spi(cs0),
+                       uart1(cts), ssp(sfrm)
+mpp22         22       gpio, sdio0(buspwr), sdio1(buspwr), spi1(mosi),
+                       lcd-spi(mosi), uart1(cts), ssp(txd)
+mpp23         23       gpio, sdio0(ledctrl), sdio1(ledctrl), spi1(sck),
+                       lcd-spi(sck), ssp(sclk)
+mpp_camera    24-39    gpio, camera
+mpp_sdio0     40-45    gpio, sdio0
+mpp_sdio1     46-51    gpio, sdio1
+mpp_audio1    52-57    gpio, i2s1/spdifo, i2s1, spdifo, twsi, ssp/spdifo, ssp,
+                       ssp/twsi
+mpp_spi0      58-61    gpio, spi0
+mpp_uart1     62-63    gpio, uart1
+mpp_nand      64-71    gpo, nand
+audio0        -        i2s, ac97
+twsi          -        none, opt1, opt2, opt3
+
+Power Management functions (pmu*):
+pmu-nc               Pin not driven by any PM function
+pmu-low              Pin driven low (0)
+pmu-high             Pin driven high (1)
+pmic(sdi)            Pin is used for PMIC SDI
+cpu-pwr-down         Pin is used for CPU_PWRDWN
+standby-pwr-down     Pin is used for STBY_PWRDWN
+core-pwr-good        Pin is used for CORE_PWR_GOOD (Pins 0-7 only)
+cpu-pwr-good         Pin is used for CPU_PWR_GOOD (Pins 8-15 only)
+bat-fault            Pin is used for BATTERY_FAULT
+ext0-wakeup          Pin is used for EXT0_WU
+ext1-wakeup          Pin is used for EXT0_WU
+ext2-wakeup          Pin is used for EXT0_WU
+pmu-blink            Pin is used for blink function
+
+Notes:
+* group "mpp_audio1" allows the following functions and gpio pins:
+  - gpio          : gpio on pins 52-57
+  - i2s1/spdifo   : audio1 i2s on pins 52-55 and spdifo on 57, no gpios
+  - i2s1          : audio1 i2s on pins 52-55, gpio on pins 56,57
+  - spdifo        : spdifo on pin 57, gpio on pins 52-55
+  - twsi          : twsi on pins 56,57, gpio on pins 52-55
+  - ssp/spdifo    : ssp on pins 52-55, spdifo on pin 57, no gpios
+  - ssp           : ssp on pins 52-55, gpio on pins 56,57
+  - ssp/twsi      : ssp on pins 52-55, twsi on pins 56,57, no gpios
+* group "audio0" internally muxes i2s0 or ac97 controller to the dedicated
+  audio0 pins.
+* group "twsi" internally muxes twsi controller to the dedicated or option pins.
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt
new file mode 100644
index 000000000..730444a9a
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,kirkwood-pinctrl.txt
@@ -0,0 +1,319 @@
+* Marvell Kirkwood SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,88f6180-pinctrl",
+              "marvell,88f6190-pinctrl", "marvell,88f6192-pinctrl",
+              "marvell,88f6281-pinctrl", "marvell,88f6282-pinctrl"
+              "marvell,98dx4122-pinctrl"
+- reg: register specifier of MPP registers
+
+This driver supports all kirkwood variants, i.e. 88f6180, 88f619x, and 88f628x.
+It also support the 88f6281-based variant in the 98dx412x Bobcat SoCs.
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+* Marvell Kirkwood 88f6180
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, nand(io2), spi(cs)
+mpp1          1        gpo, nand(io3), spi(mosi)
+mpp2          2        gpo, nand(io4), spi(sck)
+mpp3          3        gpo, nand(io5), spi(miso)
+mpp4          4        gpio, nand(io6), uart0(rxd), ptp(clk)
+mpp5          5        gpo, nand(io7), uart0(txd), ptp(trig)
+mpp6          6        sysrst(out), spi(mosi), ptp(trig)
+mpp7          7        gpo, pex(rsto), spi(cs), ptp(trig)
+mpp8          8        gpio, twsi0(sda), uart0(rts), uart1(rts), ptp(clk),
+                       mii(col)
+mpp9          9        gpio, twsi(sck), uart0(cts), uart1(cts), ptp(evreq),
+                       mii(crs)
+mpp10         10       gpo, spi(sck), uart0(txd), ptp(trig)
+mpp11         11       gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq),
+                       ptp-2(trig)
+mpp12         12       gpo, sdio(clk)
+mpp13         13       gpio, sdio(cmd), uart1(txd)
+mpp14         14       gpio, sdio(d0), uart1(rxd), mii(col)
+mpp15         15       gpio, sdio(d1), uart0(rts), uart1(txd)
+mpp16         16       gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs)
+mpp17         17       gpio, sdio(d3)
+mpp18         18       gpo, nand(io0)
+mpp19         19       gpo, nand(io1)
+mpp20         20       gpio, mii(rxerr)
+mpp21         21       gpio, audio(spdifi)
+mpp22         22       gpio, audio(spdifo)
+mpp23         23       gpio, audio(rmclk)
+mpp24         24       gpio, audio(bclk)
+mpp25         25       gpio, audio(sdo)
+mpp26         26       gpio, audio(lrclk)
+mpp27         27       gpio, audio(mclk)
+mpp28         28       gpio, audio(sdi)
+mpp29         29       gpio, audio(extclk)
+
+* Marvell Kirkwood 88f6190
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, nand(io2), spi(cs)
+mpp1          1        gpo, nand(io3), spi(mosi)
+mpp2          2        gpo, nand(io4), spi(sck)
+mpp3          3        gpo, nand(io5), spi(miso)
+mpp4          4        gpio, nand(io6), uart0(rxd), ptp(clk)
+mpp5          5        gpo, nand(io7), uart0(txd), ptp(trig), sata0(act)
+mpp6          6        sysrst(out), spi(mosi), ptp(trig)
+mpp7          7        gpo, pex(rsto), spi(cs), ptp(trig)
+mpp8          8        gpio, twsi0(sda), uart0(rts), uart1(rts), ptp(clk),
+                       mii(col), mii-1(rxerr)
+mpp9          9        gpio, twsi(sck), uart0(cts), uart1(cts), ptp(evreq),
+                       mii(crs), sata0(prsnt)
+mpp10         10       gpo, spi(sck), uart0(txd), ptp(trig)
+mpp11         11       gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq),
+                       ptp-2(trig), sata0(act)
+mpp12         12       gpo, sdio(clk)
+mpp13         13       gpio, sdio(cmd), uart1(txd)
+mpp14         14       gpio, sdio(d0), uart1(rxd), mii(col)
+mpp15         15       gpio, sdio(d1), uart0(rts), uart1(txd), sata0(act)
+mpp16         16       gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs)
+mpp17         17       gpio, sdio(d3), sata0(prsnt)
+mpp18         18       gpo, nand(io0)
+mpp19         19       gpo, nand(io1)
+mpp20         20       gpio, ge1(txd0)
+mpp21         21       gpio, ge1(txd1), sata0(act)
+mpp22         22       gpio, ge1(txd2)
+mpp23         23       gpio, ge1(txd3), sata0(prsnt)
+mpp24         24       gpio, ge1(rxd0)
+mpp25         25       gpio, ge1(rxd1)
+mpp26         26       gpio, ge1(rxd2)
+mpp27         27       gpio, ge1(rxd3)
+mpp28         28       gpio, ge1(col)
+mpp29         29       gpio, ge1(txclk)
+mpp30         30       gpio, ge1(rxclk)
+mpp31         31       gpio, ge1(rxclk)
+mpp32         32       gpio, ge1(txclko)
+mpp33         33       gpo, ge1(txclk)
+mpp34         34       gpio, ge1(txen)
+mpp35         35       gpio, ge1(rxerr), sata0(act), mii(rxerr)
+
+* Marvell Kirkwood 88f6192
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, nand(io2), spi(cs)
+mpp1          1        gpo, nand(io3), spi(mosi)
+mpp2          2        gpo, nand(io4), spi(sck)
+mpp3          3        gpo, nand(io5), spi(miso)
+mpp4          4        gpio, nand(io6), uart0(rxd), ptp(clk), sata1(act)
+mpp5          5        gpo, nand(io7), uart0(txd), ptp(trig), sata0(act)
+mpp6          6        sysrst(out), spi(mosi), ptp(trig)
+mpp7          7        gpo, pex(rsto), spi(cs), ptp(trig)
+mpp8          8        gpio, twsi0(sda), uart0(rts), uart1(rts), ptp(clk),
+                       mii(col), mii-1(rxerr), sata1(prsnt)
+mpp9          9        gpio, twsi(sck), uart0(cts), uart1(cts), ptp(evreq),
+                       mii(crs), sata0(prsnt)
+mpp10         10       gpo, spi(sck), uart0(txd), ptp(trig), sata1(act)
+mpp11         11       gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq),
+                       ptp-2(trig), sata0(act)
+mpp12         12       gpo, sdio(clk)
+mpp13         13       gpio, sdio(cmd), uart1(txd)
+mpp14         14       gpio, sdio(d0), uart1(rxd), mii(col), sata1(prsnt)
+mpp15         15       gpio, sdio(d1), uart0(rts), uart1(txd), sata0(act)
+mpp16         16       gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs),
+                       sata1(act)
+mpp17         17       gpio, sdio(d3), sata0(prsnt)
+mpp18         18       gpo, nand(io0)
+mpp19         19       gpo, nand(io1)
+mpp20         20       gpio, ge1(txd0), ts(mp0), tdm(tx0ql), audio(spdifi),
+                       sata1(act)
+mpp21         21       gpio, ge1(txd1), sata0(act), ts(mp1), tdm(rx0ql),
+                       audio(spdifo)
+mpp22         22       gpio, ge1(txd2), ts(mp2), tdm(tx2ql), audio(rmclk),
+                       sata1(prsnt)
+mpp23         23       gpio, ge1(txd3), sata0(prsnt), ts(mp3), tdm(rx2ql),
+                       audio(bclk)
+mpp24         24       gpio, ge1(rxd0), ts(mp4), tdm(spi-cs0), audio(sdo)
+mpp25         25       gpio, ge1(rxd1), ts(mp5), tdm(spi-sck), audio(lrclk)
+mpp26         26       gpio, ge1(rxd2), ts(mp6), tdm(spi-miso), audio(mclk)
+mpp27         27       gpio, ge1(rxd3), ts(mp7), tdm(spi-mosi), audio(sdi)
+mpp28         28       gpio, ge1(col), ts(mp8), tdm(int), audio(extclk)
+mpp29         29       gpio, ge1(txclk), ts(mp9), tdm(rst)
+mpp30         30       gpio, ge1(rxclk), ts(mp10), tdm(pclk)
+mpp31         31       gpio, ge1(rxclk), ts(mp11), tdm(fs)
+mpp32         32       gpio, ge1(txclko), ts(mp12), tdm(drx)
+mpp33         33       gpo, ge1(txclk), tdm(drx)
+mpp34         34       gpio, ge1(txen), tdm(spi-cs1)
+mpp35         35       gpio, ge1(rxerr), sata0(act), mii(rxerr), tdm(tx0ql)
+
+* Marvell Kirkwood 88f6281
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, nand(io2), spi(cs)
+mpp1          1        gpo, nand(io3), spi(mosi)
+mpp2          2        gpo, nand(io4), spi(sck)
+mpp3          3        gpo, nand(io5), spi(miso)
+mpp4          4        gpio, nand(io6), uart0(rxd), ptp(clk), sata1(act)
+mpp5          5        gpo, nand(io7), uart0(txd), ptp(trig), sata0(act)
+mpp6          6        sysrst(out), spi(mosi), ptp(trig)
+mpp7          7        gpo, pex(rsto), spi(cs), ptp(trig)
+mpp8          8        gpio, twsi0(sda), uart0(rts), uart1(rts), ptp(clk),
+                       mii(col), mii-1(rxerr), sata1(prsnt)
+mpp9          9        gpio, twsi(sck), uart0(cts), uart1(cts), ptp(evreq),
+                       mii(crs), sata0(prsnt)
+mpp10         10       gpo, spi(sck), uart0(txd), ptp(trig), sata1(act)
+mpp11         11       gpio, spi(miso), uart0(rxd), ptp(clk), ptp-1(evreq),
+                       ptp-2(trig), sata0(act)
+mpp12         12       gpio, sdio(clk)
+mpp13         13       gpio, sdio(cmd), uart1(txd)
+mpp14         14       gpio, sdio(d0), uart1(rxd), mii(col), sata1(prsnt)
+mpp15         15       gpio, sdio(d1), uart0(rts), uart1(txd), sata0(act)
+mpp16         16       gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs),
+                       sata1(act)
+mpp17         17       gpio, sdio(d3), sata0(prsnt)
+mpp18         18       gpo, nand(io0)
+mpp19         19       gpo, nand(io1)
+mpp20         20       gpio, ge1(txd0), ts(mp0), tdm(tx0ql), audio(spdifi),
+                       sata1(act)
+mpp21         21       gpio, ge1(txd1), sata0(act), ts(mp1), tdm(rx0ql),
+                       audio(spdifo)
+mpp22         22       gpio, ge1(txd2), ts(mp2), tdm(tx2ql), audio(rmclk),
+                       sata1(prsnt)
+mpp23         23       gpio, ge1(txd3), sata0(prsnt), ts(mp3), tdm(rx2ql),
+                       audio(bclk)
+mpp24         24       gpio, ge1(rxd0), ts(mp4), tdm(spi-cs0), audio(sdo)
+mpp25         25       gpio, ge1(rxd1), ts(mp5), tdm(spi-sck), audio(lrclk)
+mpp26         26       gpio, ge1(rxd2), ts(mp6), tdm(spi-miso), audio(mclk)
+mpp27         27       gpio, ge1(rxd3), ts(mp7), tdm(spi-mosi), audio(sdi)
+mpp28         28       gpio, ge1(col), ts(mp8), tdm(int), audio(extclk)
+mpp29         29       gpio, ge1(txclk), ts(mp9), tdm(rst)
+mpp30         30       gpio, ge1(rxclk), ts(mp10), tdm(pclk)
+mpp31         31       gpio, ge1(rxclk), ts(mp11), tdm(fs)
+mpp32         32       gpio, ge1(txclko), ts(mp12), tdm(drx)
+mpp33         33       gpo, ge1(txclk), tdm(drx)
+mpp34         34       gpio, ge1(txen), tdm(spi-cs1), sata1(act)
+mpp35         35       gpio, ge1(rxerr), sata0(act), mii(rxerr), tdm(tx0ql)
+mpp36         36       gpio, ts(mp0), tdm(spi-cs1), audio(spdifi)
+mpp37         37       gpio, ts(mp1), tdm(tx2ql), audio(spdifo)
+mpp38         38       gpio, ts(mp2), tdm(rx2ql), audio(rmclk)
+mpp39         39       gpio, ts(mp3), tdm(spi-cs0), audio(bclk)
+mpp40         40       gpio, ts(mp4), tdm(spi-sck), audio(sdo)
+mpp41         41       gpio, ts(mp5), tdm(spi-miso), audio(lrclk)
+mpp42         42       gpio, ts(mp6), tdm(spi-mosi), audio(mclk)
+mpp43         43       gpio, ts(mp7), tdm(int), audio(sdi)
+mpp44         44       gpio, ts(mp8), tdm(rst), audio(extclk)
+mpp45         45       gpio, ts(mp9), tdm(pclk)
+mpp46         46       gpio, ts(mp10), tdm(fs)
+mpp47         47       gpio, ts(mp11), tdm(drx)
+mpp48         48       gpio, ts(mp12), tdm(dtx)
+mpp49         49       gpio, ts(mp9), tdm(rx0ql), ptp(clk)
+
+* Marvell Kirkwood 88f6282
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, nand(io2), spi(cs)
+mpp1          1        gpo, nand(io3), spi(mosi)
+mpp2          2        gpo, nand(io4), spi(sck)
+mpp3          3        gpo, nand(io5), spi(miso)
+mpp4          4        gpio, nand(io6), uart0(rxd), sata1(act), lcd(hsync)
+mpp5          5        gpo, nand(io7), uart0(txd), sata0(act), lcd(vsync)
+mpp6          6        sysrst(out), spi(mosi)
+mpp7          7        gpo, spi(cs), lcd(pwm)
+mpp8          8        gpio, twsi0(sda), uart0(rts), uart1(rts), mii(col),
+                       mii-1(rxerr), sata1(prsnt)
+mpp9          9        gpio, twsi(sck), uart0(cts), uart1(cts), mii(crs),
+                       sata0(prsnt)
+mpp10         10       gpo, spi(sck), uart0(txd), sata1(act)
+mpp11         11       gpio, spi(miso), uart0(rxd), sata0(act)
+mpp12         12       gpo, sdio(clk), audio(spdifo), spi(mosi), twsi(sda)
+mpp13         13       gpio, sdio(cmd), uart1(txd), audio(rmclk), lcd(pwm)
+mpp14         14       gpio, sdio(d0), uart1(rxd), mii(col), sata1(prsnt),
+                       audio(spdifi), audio-1(sdi)
+mpp15         15       gpio, sdio(d1), uart0(rts), uart1(txd), sata0(act),
+                       spi(cs)
+mpp16         16       gpio, sdio(d2), uart0(cts), uart1(rxd), mii(crs),
+                       sata1(act), lcd(extclk)
+mpp17         17       gpio, sdio(d3), sata0(prsnt), sata1(act), twsi1(sck)
+mpp18         18       gpo, nand(io0), pex(clkreq)
+mpp19         19       gpo, nand(io1)
+mpp20         20       gpio, ge1(txd0), ts(mp0), tdm(tx0ql), audio(spdifi),
+                       sata1(act), lcd(d0)
+mpp21         21       gpio, ge1(txd1), sata0(act), ts(mp1), tdm(rx0ql),
+                       audio(spdifo), lcd(d1)
+mpp22         22       gpio, ge1(txd2), ts(mp2), tdm(tx2ql), audio(rmclk),
+                       sata1(prsnt), lcd(d2)
+mpp23         23       gpio, ge1(txd3), sata0(prsnt), ts(mp3), tdm(rx2ql),
+                       audio(bclk), lcd(d3)
+mpp24         24       gpio, ge1(rxd0), ts(mp4), tdm(spi-cs0), audio(sdo),
+                       lcd(d4)
+mpp25         25       gpio, ge1(rxd1), ts(mp5), tdm(spi-sck), audio(lrclk),
+                       lcd(d5)
+mpp26         26       gpio, ge1(rxd2), ts(mp6), tdm(spi-miso), audio(mclk),
+                       lcd(d6)
+mpp27         27       gpio, ge1(rxd3), ts(mp7), tdm(spi-mosi), audio(sdi),
+                       lcd(d7)
+mpp28         28       gpio, ge1(col), ts(mp8), tdm(int), audio(extclk),
+                       lcd(d8)
+mpp29         29       gpio, ge1(txclk), ts(mp9), tdm(rst), lcd(d9)
+mpp30         30       gpio, ge1(rxclk), ts(mp10), tdm(pclk), lcd(d10)
+mpp31         31       gpio, ge1(rxclk), ts(mp11), tdm(fs), lcd(d11)
+mpp32         32       gpio, ge1(txclko), ts(mp12), tdm(drx), lcd(d12)
+mpp33         33       gpo, ge1(txclk), tdm(drx), lcd(d13)
+mpp34         34       gpio, ge1(txen), tdm(spi-cs1), sata1(act), lcd(d14)
+mpp35         35       gpio, ge1(rxerr), sata0(act), mii(rxerr), tdm(tx0ql),
+                       lcd(d15)
+mpp36         36       gpio, ts(mp0), tdm(spi-cs1), audio(spdifi), twsi1(sda)
+mpp37         37       gpio, ts(mp1), tdm(tx2ql), audio(spdifo), twsi1(sck)
+mpp38         38       gpio, ts(mp2), tdm(rx2ql), audio(rmclk), lcd(d18)
+mpp39         39       gpio, ts(mp3), tdm(spi-cs0), audio(bclk), lcd(d19)
+mpp40         40       gpio, ts(mp4), tdm(spi-sck), audio(sdo), lcd(d20)
+mpp41         41       gpio, ts(mp5), tdm(spi-miso), audio(lrclk), lcd(d21)
+mpp42         42       gpio, ts(mp6), tdm(spi-mosi), audio(mclk), lcd(d22)
+mpp43         43       gpio, ts(mp7), tdm(int), audio(sdi), lcd(d23)
+mpp44         44       gpio, ts(mp8), tdm(rst), audio(extclk), lcd(clk)
+mpp45         45       gpio, ts(mp9), tdm(pclk), lcd(e)
+mpp46         46       gpio, ts(mp10), tdm(fs), lcd(hsync)
+mpp47         47       gpio, ts(mp11), tdm(drx), lcd(vsync)
+mpp48         48       gpio, ts(mp12), tdm(dtx), lcd(d16)
+mpp49         49       gpo, tdm(rx0ql), pex(clkreq), lcd(d17)
+
+* Marvell Bobcat 98dx4122
+
+name          pins     functions
+================================================================================
+mpp0          0        gpio, nand(io2), spi(cs)
+mpp1          1        gpo, nand(io3), spi(mosi)
+mpp2          2        gpo, nand(io4), spi(sck)
+mpp3          3        gpo, nand(io5), spi(miso)
+mpp4          4        gpio, nand(io6), uart0(rxd)
+mpp5          5        gpo, nand(io7), uart0(txd)
+mpp6          6        sysrst(out), spi(mosi)
+mpp7          7        gpo, pex(rsto), spi(cs)
+mpp8          8        gpio, twsi0(sda), uart0(rts), uart1(rts)
+mpp9          9        gpio, twsi(sck), uart0(cts), uart1(cts)
+mpp10         10       gpo, spi(sck), uart0(txd)
+mpp11         11       gpio, spi(miso), uart0(rxd)
+mpp13         13       gpio, uart1(txd)
+mpp14         14       gpio, uart1(rxd)
+mpp15         15       gpio, uart0(rts)
+mpp16         16       gpio, uart0(cts)
+mpp18         18       gpo, nand(io0)
+mpp19         19       gpo, nand(io1)
+mpp34         34       gpio
+mpp35         35       gpio
+mpp36         36       gpio
+mpp37         37       gpio
+mpp38         38       gpio
+mpp39         39       gpio
+mpp40         40       gpio
+mpp41         41       gpio
+mpp42         42       gpio
+mpp43         43       gpio
+mpp44         44       gpio
+mpp45         45       gpio
+mpp49         49       gpio
+
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt
new file mode 100644
index 000000000..0c09f4eb2
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,mvebu-pinctrl.txt
@@ -0,0 +1,46 @@
+* Marvell SoC pinctrl core driver for mpp
+
+The pinctrl driver enables Marvell SoCs to configure the multi-purpose pins
+(mpp) to a specific function. For each SoC family there is a SoC specific
+driver using this core driver.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+A Marvell SoC pin configuration node is a node of a group of pins which can
+be used for a specific device or function. Each node requires one or more
+mpp pins or group of pins and a mpp function common to all pins.
+
+Required properties for pinctrl driver:
+- compatible: "marvell,<soc>-pinctrl"
+  Please refer to each marvell,<soc>-pinctrl.txt binding doc for supported SoCs.
+
+Required properties for pin configuration node:
+- marvell,pins: string array of mpp pins or group of pins to be muxed.
+- marvell,function: string representing a function to mux to for all
+    marvell,pins given in this pin configuration node. The function has to be
+    common for all marvell,pins. Please refer to marvell,<soc>-pinctrl.txt for
+    valid pin/pin group names and available function names for each SoC.
+
+Examples:
+
+uart1: serial@12100 {
+	compatible = "ns16550a";
+	reg = <0x12100 0x100>;
+	reg-shift = <2>;
+	interrupts = <7>;
+
+	pinctrl-0 = <&pmx_uart1_sw>;
+	pinctrl-names = "default";
+};
+
+pinctrl: pinctrl@d0200 {
+	compatible = "marvell,dove-pinctrl";
+	reg = <0xd0200 0x14>, <0xd0440 0x04>, <0xd802c 0x08>;
+
+	pmx_uart1_sw: pmx-uart1-sw {
+		marvell,pins = "mpp_uart1";
+		marvell,function = "uart1";
+	};
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt
new file mode 100644
index 000000000..27570a3a1
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,orion-pinctrl.txt
@@ -0,0 +1,91 @@
+* Marvell Orion SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,88f5181l-pinctrl", "marvell,88f5182-pinctrl",
+              "marvell,88f5281-pinctrl"
+
+- reg: two register areas, the first one describing the first two
+  contiguous MPP registers, and the second one describing the single
+  final MPP register, separated from the previous one.
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+* Marvell Orion 88f5181l
+
+name          pins     functions
+================================================================================
+mpp0          0        pcie(rstout), pci(req2), gpio
+mpp1          1        gpio, pci(gnt2)
+mpp2          2        gpio, pci(req3), pci-1(pme)
+mpp3          3        gpio, pci(gnt3)
+mpp4          4        gpio, pci(req4)
+mpp5          5        gpio, pci(gnt4)
+mpp6          6        gpio, pci(req5), pci-1(clk)
+mpp7          7        gpio, pci(gnt5), pci-1(clk)
+mpp8          8        gpio, ge(col)
+mpp9          9        gpio, ge(rxerr)
+mpp10         10       gpio, ge(crs)
+mpp11         11       gpio, ge(txerr)
+mpp12         12       gpio, ge(txd4)
+mpp13         13       gpio, ge(txd5)
+mpp14         14       gpio, ge(txd6)
+mpp15         15       gpio, ge(txd7)
+mpp16         16       ge(rxd4)
+mpp17         17       ge(rxd5)
+mpp18         18       ge(rxd6)
+mpp19         19       ge(rxd7)
+
+* Marvell Orion 88f5182
+
+name          pins     functions
+================================================================================
+mpp0          0        pcie(rstout), pci(req2), gpio
+mpp1          1        gpio, pci(gnt2)
+mpp2          2        gpio, pci(req3), pci-1(pme)
+mpp3          3        gpio, pci(gnt3)
+mpp4          4        gpio, pci(req4), bootnand(re), sata0(prsnt)
+mpp5          5        gpio, pci(gnt4), bootnand(we), sata1(prsnt)
+mpp6          6        gpio, pci(req5), nand(re0), sata0(act)
+mpp7          7        gpio, pci(gnt5), nand(we0), sata1(act)
+mpp8          8        gpio, ge(col)
+mpp9          9        gpio, ge(rxerr)
+mpp10         10       gpio, ge(crs)
+mpp11         11       gpio, ge(txerr)
+mpp12         12       gpio, ge(txd4), nand(re1), sata0(ledprsnt)
+mpp13         13       gpio, ge(txd5), nand(we1), sata1(ledprsnt)
+mpp14         14       gpio, ge(txd6), nand(re2), sata0(ledact)
+mpp15         15       gpio, ge(txd7), nand(we2), sata1(ledact)
+mpp16         16       uart1(rxd), ge(rxd4), gpio
+mpp17         17       uart1(txd), ge(rxd5), gpio
+mpp18         18       uart1(cts), ge(rxd6), gpio
+mpp19         19       uart1(rts), ge(rxd7), gpio
+
+* Marvell Orion 88f5281
+
+name          pins     functions
+================================================================================
+mpp0          0        pcie(rstout), pci(req2), gpio
+mpp1          1        gpio, pci(gnt2)
+mpp2          2        gpio, pci(req3), pci(pme)
+mpp3          3        gpio, pci(gnt3)
+mpp4          4        gpio, pci(req4), bootnand(re)
+mpp5          5        gpio, pci(gnt4), bootnand(we)
+mpp6          6        gpio, pci(req5), nand(re0)
+mpp7          7        gpio, pci(gnt5), nand(we0)
+mpp8          8        gpio, ge(col)
+mpp9          9        gpio, ge(rxerr)
+mpp10         10       gpio, ge(crs)
+mpp11         11       gpio, ge(txerr)
+mpp12         12       gpio, ge(txd4), nand(re1)
+mpp13         13       gpio, ge(txd5), nand(we1)
+mpp14         14       gpio, ge(txd6), nand(re2)
+mpp15         15       gpio, ge(txd7), nand(we2)
+mpp16         16       uart1(rxd), ge(rxd4)
+mpp17         17       uart1(txd), ge(rxd5)
+mpp18         18       uart1(cts), ge(rxd6)
+mpp19         19       uart1(rts), ge(rxd7)
diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
new file mode 100644
index 000000000..3f6a524cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
@@ -0,0 +1,96 @@
+== Amlogic Meson pinmux controller ==
+
+Required properties for the root node:
+ - compatible: "amlogic,meson8-pinctrl" or "amlogic,meson8b-pinctrl"
+ - reg: address and size of registers controlling irq functionality
+
+=== GPIO sub-nodes ===
+
+The 2 power domains of the controller (regular and always-on) are
+represented as sub-nodes and each of them acts as a GPIO controller.
+
+Required properties for sub-nodes are:
+ - reg: should contain address and size for mux, pull-enable, pull and
+   gpio register sets
+ - reg-names: an array of strings describing the "reg" entries. Must
+   contain "mux", "pull" and "gpio". "pull-enable" is optional and
+   when it is missing the "pull" registers are used instead
+ - gpio-controller: identifies the node as a gpio controller
+ - #gpio-cells: must be 2
+
+Valid sub-node names are:
+ - "banks" for the regular domain
+ - "ao-bank" for the always-on domain
+
+=== Other sub-nodes ===
+
+Child nodes without the "gpio-controller" represent some desired
+configuration for a pin or a group. Those nodes can be pinmux nodes or
+configuration nodes.
+
+Required properties for pinmux nodes are:
+ - groups: a list of pinmux groups. The list of all available groups
+   depends on the SoC and can be found in driver sources.
+ - function: the name of a function to activate for the specified set
+   of groups. The list of all available functions depends on the SoC
+   and can be found in driver sources.
+
+Required properties for configuration nodes:
+ - pins: a list of pin names
+
+Configuration nodes support the generic properties "bias-disable",
+"bias-pull-up" and "bias-pull-down", described in file
+pinctrl-bindings.txt
+
+=== Example ===
+
+	pinctrl: pinctrl@c1109880 {
+		compatible = "amlogic,meson8-pinctrl";
+		reg = <0xc1109880 0x10>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio: banks@c11080b0 {
+			reg = <0xc11080b0 0x28>,
+			      <0xc11080e8 0x18>,
+			      <0xc1108120 0x18>,
+			      <0xc1108030 0x30>;
+			reg-names = "mux", "pull", "pull-enable", "gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+               };
+
+		gpio_ao: ao-bank@c1108030 {
+			reg = <0xc8100014 0x4>,
+			      <0xc810002c 0x4>,
+			      <0xc8100024 0x8>;
+			reg-names = "mux", "pull", "gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		nand {
+			mux {
+				groups = "nand_io", "nand_io_ce0", "nand_io_ce1",
+					 "nand_io_rb0", "nand_ale", "nand_cle",
+					 "nand_wen_clk", "nand_ren_clk", "nand_dqs",
+					 "nand_ce2", "nand_ce3";
+				function = "nand";
+			};
+		};
+
+		uart_ao_a {
+			mux {
+				groups = "uart_tx_ao_a", "uart_rx_ao_a",
+					 "uart_cts_ao_a", "uart_rts_ao_a";
+				function = "uart_ao";
+			};
+
+			conf {
+				pins = "GPIOAO_0", "GPIOAO_1",
+				       "GPIOAO_2", "GPIOAO_3";
+				bias-disable;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt
new file mode 100644
index 000000000..fb70856c5
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt
@@ -0,0 +1,131 @@
+NVIDIA Tegra114 pinmux controller
+
+The Tegra114 pinctrl binding is very similar to the Tegra20 and Tegra30
+pinctrl binding, as described in nvidia,tegra20-pinmux.txt and
+nvidia,tegra30-pinmux.txt. In fact, this document assumes that binding as
+a baseline, and only documents the differences between the two bindings.
+
+Required properties:
+- compatible: "nvidia,tegra114-pinmux"
+- reg: Should contain the register physical address and length for each of
+  the pad control and mux registers. The first bank of address must be the
+  driver strength pad control register address and second bank address must
+  be pinmux register address.
+
+Tegra114 adds the following optional properties for pin configuration subnodes:
+- nvidia,enable-input: Integer. Enable the pin's input path. 0: no, 1: yes.
+- nvidia,open-drain: Integer. Enable open drain mode. 0: no, 1: yes.
+- nvidia,lock: Integer. Lock the pin configuration against further changes
+    until reset. 0: no, 1: yes.
+- nvidia,io-reset: Integer. Reset the IO path. 0: no, 1: yes.
+- nvidia,rcv-sel: Integer. Select VIL/VIH receivers. 0: normal, 1: high.
+- nvidia,drive-type: Integer. Valid range 0...3.
+
+As with Tegra20 and Terga30, see the Tegra TRM for complete details regarding
+which groups support which functionality.
+
+Valid values for pin and group names are:
+
+  per-pin mux groups:
+
+    These all support nvidia,function, nvidia,tristate, nvidia,pull,
+    nvidia,enable-input, nvidia,lock. Some support nvidia,open-drain,
+    nvidia,io-reset and nvidia,rcv-sel.
+
+    ulpi_data0_po1, ulpi_data1_po2, ulpi_data2_po3, ulpi_data3_po4,
+    ulpi_data4_po5, ulpi_data5_po6, ulpi_data6_po7, ulpi_data7_po0,
+    ulpi_clk_py0, ulpi_dir_py1, ulpi_nxt_py2, ulpi_stp_py3, dap3_fs_pp0,
+    dap3_din_pp1, dap3_dout_pp2, dap3_sclk_pp3, pv0, pv1, sdmmc1_clk_pz0,
+    sdmmc1_cmd_pz1, sdmmc1_dat3_py4, sdmmc1_dat2_py5, sdmmc1_dat1_py6,
+    sdmmc1_dat0_py7, clk2_out_pw5, clk2_req_pcc5, hdmi_int_pn7, ddc_scl_pv4,
+    ddc_sda_pv5, uart2_rxd_pc3, uart2_txd_pc2, uart2_rts_n_pj6,
+    uart2_cts_n_pj5, uart3_txd_pw6, uart3_rxd_pw7, uart3_cts_n_pa1,
+    uart3_rts_n_pc0, pu0, pu1, pu2, pu3, pu4, pu5, pu6, gen1_i2c_sda_pc5,
+    gen1_i2c_scl_pc4, dap4_fs_pp4, dap4_din_pp5, dap4_dout_pp6, dap4_sclk_pp7,
+    clk3_out_pee0, clk3_req_pee1, gmi_wp_n_pc7, gmi_iordy_pi5, gmi_wait_pi7,
+    gmi_adv_n_pk0, gmi_clk_pk1, gmi_cs0_n_pj0, gmi_cs1_n_pj2, gmi_cs2_n_pk3,
+    gmi_cs3_n_pk4, gmi_cs4_n_pk2, gmi_cs6_n_pi3, gmi_cs7_n_pi6, gmi_ad0_pg0,
+    gmi_ad1_pg1, gmi_ad2_pg2, gmi_ad3_pg3, gmi_ad4_pg4, gmi_ad5_pg5,
+    gmi_ad6_pg6, gmi_ad7_pg7, gmi_ad8_ph0, gmi_ad9_ph1, gmi_ad10_ph2,
+    gmi_ad11_ph3, gmi_ad12_ph4, gmi_ad13_ph5, gmi_ad14_ph6, gmi_ad15_ph7,
+    gmi_a16_pj7, gmi_a17_pb0, gmi_a18_pb1, gmi_a19_pk7, gmi_wr_n_pi0,
+    gmi_oe_n_pi1, gmi_dqs_p_pj3, gmi_rst_n_pi4, gen2_i2c_scl_pt5,
+    gen2_i2c_sda_pt6, sdmmc4_clk_pcc4, sdmmc4_cmd_pt7, sdmmc4_dat0_paa0,
+    sdmmc4_dat1_paa1, sdmmc4_dat2_paa2, sdmmc4_dat3_paa3, sdmmc4_dat4_paa4,
+    sdmmc4_dat5_paa5, sdmmc4_dat6_paa6, sdmmc4_dat7_paa7, cam_mclk_pcc0,
+    pcc1, pbb0, cam_i2c_scl_pbb1, cam_i2c_sda_pbb2, pbb3, pbb4, pbb5, pbb6,
+    pbb7, pcc2, pwr_i2c_scl_pz6, pwr_i2c_sda_pz7, kb_row0_pr0, kb_row1_pr1,
+    kb_row2_pr2, kb_row3_pr3, kb_row4_pr4, kb_row5_pr5, kb_row6_pr6,
+    kb_row7_pr7, kb_row8_ps0, kb_row9_ps1, kb_row10_ps2, kb_col0_pq0,
+    kb_col1_pq1, kb_col2_pq2, kb_col3_pq3, kb_col4_pq4, kb_col5_pq5,
+    kb_col6_pq6, kb_col7_pq7, clk_32k_out_pa0, sys_clk_req_pz5, core_pwr_req,
+    cpu_pwr_req, pwr_int_n, owr, dap1_fs_pn0, dap1_din_pn1, dap1_dout_pn2,
+    dap1_sclk_pn3, clk1_req_pee2, clk1_out_pw4, spdif_in_pk6, spdif_out_pk5,
+    dap2_fs_pa2, dap2_din_pa4, dap2_dout_pa5, dap2_sclk_pa3, dvfs_pwm_px0,
+    gpio_x1_aud_px1, gpio_x3_aud_px3, dvfs_clk_px2, gpio_x4_aud_px4,
+    gpio_x5_aud_px5, gpio_x6_aud_px6, gpio_x7_aud_px7, sdmmc3_clk_pa6,
+    sdmmc3_cmd_pa7, sdmmc3_dat0_pb7, sdmmc3_dat1_pb6, sdmmc3_dat2_pb5,
+    sdmmc3_dat3_pb4, hdmi_cec_pee3, sdmmc1_wp_n_pv3, sdmmc3_cd_n_pv2,
+    gpio_w2_aud_pw2, gpio_w3_aud_pw3, usb_vbus_en0_pn4, usb_vbus_en1_pn5,
+    sdmmc3_clk_lb_in_pee5, sdmmc3_clk_lb_out_pee4, reset_out_n.
+
+  drive groups:
+
+    These all support nvidia,pull-down-strength, nvidia,pull-up-strength,
+    nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all
+    support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode
+    and nvidia,drive-type.
+
+    ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, dap1, dap2, dap3, dap4,
+    dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg,
+    gmh, owr, uda.
+
+Valid values for nvidia,functions are:
+
+  blink, cec, cldvfs, clk12, cpu, dap, dap1, dap2, dev3, displaya,
+  displaya_alt, displayb, dtv, emc_dll, extperiph1, extperiph2,
+  extperiph3, gmi, gmi_alt, hda, hsi, i2c1, i2c2, i2c3, i2c4, i2cpwr,
+  i2s0, i2s1, i2s2, i2s3, i2s4, irda, kbc, nand, nand_alt, owr, pmi,
+  pwm0, pwm1, pwm2, pwm3, pwron, reset_out_n, rsvd1, rsvd2, rsvd3,
+  rsvd4, sdmmc1, sdmmc2, sdmmc3, sdmmc4, soc, spdif, spi1, spi2, spi3,
+  spi4, spi5, spi6, sysclk, trace, uarta, uartb, uartc, uartd, ulpi,
+  usb, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6, vi, vi_alt1, vi_alt3
+
+Example:
+
+	pinmux: pinmux {
+		compatible = "nvidia,tegra114-pinmux";
+		reg = <0x70000868 0x148		/* Pad control registers */
+		       0x70003000 0x40c>;	/* PinMux registers */
+	};
+
+Example board file extract:
+
+	pinctrl {
+		sdmmc4_default: pinmux {
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4",
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+			};
+			sdmmc4_dat0_paa0 {
+				nvidia,pins = "sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+			};
+		};
+	};
+
+	sdhci@78000400 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc4_default>;
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt
new file mode 100644
index 000000000..ecb5c0d25
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt
@@ -0,0 +1,153 @@
+NVIDIA Tegra124 pinmux controller
+
+The Tegra124 pinctrl binding is very similar to the Tegra20 and Tegra30
+pinctrl binding, as described in nvidia,tegra20-pinmux.txt and
+nvidia,tegra30-pinmux.txt. In fact, this document assumes that binding as
+a baseline, and only documents the differences between the two bindings.
+
+Required properties:
+- compatible: For Tegra124, must contain "nvidia,tegra124-pinmux".  For
+  Tegra132, must contain '"nvidia,tegra132-pinmux", "nvidia-tegra124-pinmux"'.
+- reg: Should contain a list of base address and size pairs for:
+    -- first entry - the drive strength and pad control registers.
+    -- second entry - the pinmux registers
+    -- third entry - the MIPI_PAD_CTRL register
+
+Tegra124 adds the following optional properties for pin configuration subnodes.
+The macros for options are defined in the
+	include/dt-binding/pinctrl/pinctrl-tegra.h.
+- nvidia,enable-input: Integer. Enable the pin's input path.
+		enable :TEGRA_PIN_ENABLE0 and
+		disable or output only: TEGRA_PIN_DISABLE.
+- nvidia,open-drain: Integer.
+		enable: TEGRA_PIN_ENABLE.
+		disable: TEGRA_PIN_DISABLE.
+- nvidia,lock: Integer. Lock the pin configuration against further changes
+    until reset.
+		enable: TEGRA_PIN_ENABLE.
+		disable: TEGRA_PIN_DISABLE.
+- nvidia,io-reset: Integer. Reset the IO path.
+		enable: TEGRA_PIN_ENABLE.
+		disable: TEGRA_PIN_DISABLE.
+- nvidia,rcv-sel: Integer. Select VIL/VIH receivers.
+		normal: TEGRA_PIN_DISABLE
+		high: TEGRA_PIN_ENABLE
+
+Please refer the Tegra TRM for complete details regarding which groups
+support which functionality.
+
+Valid values for pin and group names are:
+
+  per-pin mux groups:
+
+    These all support nvidia,function, nvidia,tristate, nvidia,pull,
+    nvidia,enable-input. Some support nvidia,lock nvidia,open-drain,
+    nvidia,io-reset and nvidia,rcv-sel.
+
+	ulpi_data0_po1, ulpi_data1_po2, ulpi_data2_po3, ulpi_data3_po4,
+	ulpi_data4_po5, ulpi_data5_po6, ulpi_data6_po7, ulpi_data7_po0,
+	ulpi_clk_py0, ulpi_dir_py1, ulpi_nxt_py2, ulpi_stp_py3, dap3_fs_pp0,
+	dap3_din_pp1, dap3_dout_pp2, dap3_sclk_pp3, pv0, pv1, sdmmc1_clk_pz0,
+	sdmmc1_cmd_pz1, sdmmc1_dat3_py4, sdmmc1_dat2_py5, sdmmc1_dat1_py6,
+	sdmmc1_dat0_py7, clk2_out_pw5, clk2_req_pcc5, hdmi_int_pn7, ddc_scl_pv4,
+	ddc_sda_pv5, uart2_rxd_pc3, uart2_txd_pc2, uart2_rts_n_pj6,
+	uart2_cts_n_pj5, uart3_txd_pw6, uart3_rxd_pw7, uart3_cts_n_pa1,
+	uart3_rts_n_pc0, pu0, pu1, pu2, pu3, pu4, pu5, pu6, gen1_i2c_scl_pc4,
+	gen1_i2c_sda_pc5, dap4_fs_pp4, dap4_din_pp5, dap4_dout_pp6,
+	dap4_sclk_pp7, clk3_out_pee0, clk3_req_pee1, pc7, pi5, pi7, pk0, pk1,
+	pj0, pj2, pk3, pk4, pk2, pi3, pi6, pg0, pg1, pg2, pg3, pg4, pg5, pg6,
+	pg7, ph0, ph1, ph2, ph3, ph4, ph5, ph6, ph7, pj7, pb0, pb1, pk7, pi0,
+	pi1, pi2, pi4, gen2_i2c_scl_pt5, gen2_i2c_sda_pt6, sdmmc4_clk_pcc4,
+	sdmmc4_cmd_pt7, sdmmc4_dat0_paa0, sdmmc4_dat1_paa1, sdmmc4_dat2_paa2,
+	sdmmc4_dat3_paa3, sdmmc4_dat4_paa4, sdmmc4_dat5_paa5, sdmmc4_dat6_paa6,
+	sdmmc4_dat7_paa7, cam_mclk_pcc0, pcc1, pbb0, cam_i2c_scl_pbb1,
+	cam_i2c_sda_pbb2, pbb3, pbb4, pbb5, pbb6, pbb7, pcc2, jtag_rtck,
+	pwr_i2c_scl_pz6, pwr_i2c_sda_pz7, kb_row0_pr0, kb_row1_pr1, kb_row2_pr2,
+	kb_row3_pr3, kb_row4_pr4, kb_row5_pr5, kb_row6_pr6, kb_row7_pr7,
+	kb_row8_ps0, kb_row9_ps1, kb_row10_ps2, kb_row11_ps3, kb_row12_ps4,
+	kb_row13_ps5, kb_row14_ps6, kb_row15_ps7, kb_col0_pq0, kb_col1_pq1,
+	kb_col2_pq2, kb_col3_pq3, kb_col4_pq4, kb_col5_pq5, kb_col6_pq6,
+	kb_col7_pq7, clk_32k_out_pa0, core_pwr_req, cpu_pwr_req, pwr_int_n,
+	clk_32k_in, owr, dap1_fs_pn0, dap1_din_pn1, dap1_dout_pn2,
+	dap1_sclk_pn3, dap_mclk1_req_pee2, dap_mclk1_pw4, spdif_in_pk6,
+	spdif_out_pk5, dap2_fs_pa2, dap2_din_pa4, dap2_dout_pa5, dap2_sclk_pa3,
+	dvfs_pwm_px0, gpio_x1_aud_px1, gpio_x3_aud_px3, dvfs_clk_px2,
+	gpio_x4_aud_px4, gpio_x5_aud_px5, gpio_x6_aud_px6, gpio_x7_aud_px7,
+	sdmmc3_clk_pa6, sdmmc3_cmd_pa7, sdmmc3_dat0_pb7, sdmmc3_dat1_pb6,
+	sdmmc3_dat2_pb5, sdmmc3_dat3_pb4, pex_l0_rst_n_pdd1,
+	pex_l0_clkreq_n_pdd2, pex_wake_n_pdd3, pex_l1_rst_n_pdd5,
+	pex_l1_clkreq_n_pdd6, hdmi_cec_pee3, sdmmc1_wp_n_pv3,
+	sdmmc3_cd_n_pv2, gpio_w2_aud_pw2, gpio_w3_aud_pw3, usb_vbus_en0_pn4,
+	usb_vbus_en1_pn5, sdmmc3_clk_lb_out_pee4, sdmmc3_clk_lb_in_pee5,
+	gmi_clk_lb, reset_out_n, kb_row16_pt0, kb_row17_pt1, usb_vbus_en2_pff1,
+	pff2, dp_hpd_pff0,
+
+  drive groups:
+
+    These all support nvidia,pull-down-strength, nvidia,pull-up-strength,
+    nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all
+    support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode
+    and nvidia,drive-type.
+
+    ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, dap1, dap2, dap3, dap4,
+    dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg,
+    gmh, owr, uda, gpv, dev3, cec, usb_vbus_en, ao3, ao0, hv0, sdio4, ao4.
+
+  MIPI pad control groups:
+
+    These support only the nvidia,function property.
+
+    dsi_b
+
+Valid values for nvidia,functions are:
+
+  blink, cec, cldvfs, clk12, cpu, dap, dap1, dap2, dev3, displaya,
+  displaya_alt, displayb, dtv, extperiph1, extperiph2, extperiph3,
+  gmi, gmi_alt, hda, hsi, i2c1, i2c2, i2c3, i2c4, i2cpwr, i2s0,
+  i2s1, i2s2, i2s3, i2s4, irda, kbc, owr, pmi, pwm0, pwm1, pwm2, pwm3,
+  pwron, reset_out_n, rsvd1, rsvd2, rsvd3, rsvd4, sdmmc1, sdmmc2, sdmmc3,
+  sdmmc4, soc, spdif, spi1, spi2, spi3, spi4, spi5, spi6, trace, uarta,
+  uartb, uartc, uartd, ulpi, usb, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6,
+  vi, vi_alt1, vi_alt3, vimclk2, vimclk2_alt, sata, ccla, pe0, pe, pe1,
+  dp, rtck, sys, clk tmds, csi, dsi_b
+
+Example:
+
+	pinmux: pinmux {
+		compatible = "nvidia,tegra124-pinmux";
+		reg = <0x0 0x70000868 0x0 0x164>, /* Pad control registers */
+		      <0x0 0x70003000 0x0 0x434>, /* Mux registers */
+		      <0x0 0x70000820 0x0 0x8>;   /* MIPI pad control */
+	};
+
+Example pinmux entries:
+
+	pinctrl {
+		sdmmc4_default: pinmux {
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4",
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat0_paa0 {
+				nvidia,pins = "sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+		};
+	};
+
+	sdhci@78000400 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc4_default>;
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt
new file mode 100644
index 000000000..30676ded8
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt
@@ -0,0 +1,129 @@
+Device tree binding for NVIDIA Tegra XUSB pad controller
+========================================================
+
+The Tegra XUSB pad controller manages a set of lanes, each of which can be
+assigned to one out of a set of different pads. Some of these pads have an
+associated PHY that must be powered up before the pad can be used.
+
+This document defines the device-specific binding for the XUSB pad controller.
+
+Refer to pinctrl-bindings.txt in this directory for generic information about
+pin controller device tree bindings and ../phy/phy-bindings.txt for details on
+how to describe and reference PHYs in device trees.
+
+Required properties:
+--------------------
+- compatible: For Tegra124, must contain "nvidia,tegra124-xusb-padctl".
+  Otherwise, must contain '"nvidia,<chip>-xusb-padctl",
+  "nvidia-tegra124-xusb-padctl"', where <chip> is tegra132 or tegra210.
+- reg: Physical base address and length of the controller's registers.
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - padctl
+- #phy-cells: Should be 1. The specifier is the index of the PHY to reference.
+  See <dt-bindings/pinctrl/pinctrl-tegra-xusb.h> for the list of valid values.
+
+Lane muxing:
+------------
+
+Child nodes contain the pinmux configurations following the conventions from
+the pinctrl-bindings.txt document. Typically a single, static configuration is
+given and applied at boot time.
+
+Each subnode describes groups of lanes along with parameters and pads that
+they should be assigned to. The name of these subnodes is not important. All
+subnodes should be parsed solely based on their content.
+
+Each subnode only applies the parameters that are explicitly listed. In other
+words, if a subnode that lists a function but no pin configuration parameters
+implies no information about any pin configuration parameters. Similarly, a
+subnode that describes only an IDDQ parameter implies no information about
+what function the pins are assigned to. For this reason even seemingly boolean
+values are actually tristates in this binding: unspecified, off or on.
+Unspecified is represented as an absent property, and off/on are represented
+as integer values 0 and 1.
+
+Required properties:
+- nvidia,lanes: An array of strings. Each string is the name of a lane.
+
+Optional properties:
+- nvidia,function: A string that is the name of the function (pad) that the
+  pin or group should be assigned to. Valid values for function names are
+  listed below.
+- nvidia,iddq: Enables IDDQ mode of the lane. (0: no, 1: yes)
+
+Note that not all of these properties are valid for all lanes. Lanes can be
+divided into three groups:
+
+  - otg-0, otg-1, otg-2:
+
+    Valid functions for this group are: "snps", "xusb", "uart", "rsvd".
+
+    The nvidia,iddq property does not apply to this group.
+
+  - ulpi-0, hsic-0, hsic-1:
+
+    Valid functions for this group are: "snps", "xusb".
+
+    The nvidia,iddq property does not apply to this group.
+
+  - pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, sata-0:
+
+    Valid functions for this group are: "pcie", "usb3", "sata", "rsvd".
+
+
+Example:
+========
+
+SoC file extract:
+-----------------
+
+	padctl@0,7009f000 {
+		compatible = "nvidia,tegra124-xusb-padctl";
+		reg = <0x0 0x7009f000 0x0 0x1000>;
+		resets = <&tegra_car 142>;
+		reset-names = "padctl";
+
+		#phy-cells = <1>;
+	};
+
+Board file extract:
+-------------------
+
+	pcie-controller@0,01003000 {
+		...
+
+		phys = <&padctl 0>;
+		phy-names = "pcie";
+
+		...
+	};
+
+	...
+
+	padctl: padctl@0,7009f000 {
+		pinctrl-0 = <&padctl_default>;
+		pinctrl-names = "default";
+
+		padctl_default: pinmux {
+			usb3 {
+				nvidia,lanes = "pcie-0", "pcie-1";
+				nvidia,function = "usb3";
+				nvidia,iddq = <0>;
+			};
+
+			pcie {
+				nvidia,lanes = "pcie-2", "pcie-3",
+					       "pcie-4";
+				nvidia,function = "pcie";
+				nvidia,iddq = <0>;
+			};
+
+			sata {
+				nvidia,lanes = "sata-0";
+				nvidia,function = "sata";
+				nvidia,iddq = <0>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt
new file mode 100644
index 000000000..3c8ce28ba
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt
@@ -0,0 +1,143 @@
+NVIDIA Tegra20 pinmux controller
+
+Required properties:
+- compatible: "nvidia,tegra20-pinmux"
+- reg: Should contain the register physical address and length for each of
+  the tri-state, mux, pull-up/down, and pad control register sets.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Tegra's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, tristate, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function or tristate parameter. For this
+reason, even seemingly boolean values are actually tristates in this binding:
+unspecified, off, or on. Unspecified is represented as an absent property,
+and off/on are represented as integer values 0 and 1.
+
+Required subnode-properties:
+- nvidia,pins : An array of strings. Each string contains the name of a pin or
+    group. Valid values for these names are listed below.
+
+Optional subnode-properties:
+- nvidia,function: A string containing the name of the function to mux to the
+  pin or group. Valid values for function names are listed below. See the Tegra
+  TRM to determine which are valid for each pin or group.
+- nvidia,pull: Integer, representing the pull-down/up to apply to the pin.
+    0: none, 1: down, 2: up.
+- nvidia,tristate: Integer.
+    0: drive, 1: tristate.
+- nvidia,high-speed-mode: Integer. Enable high speed mode the pins.
+    0: no, 1: yes.
+- nvidia,schmitt: Integer. Enables Schmitt Trigger on the input.
+    0: no, 1: yes.
+- nvidia,low-power-mode: Integer. Valid values 0-3. 0 is least power, 3 is
+    most power. Controls the drive power or current. See "Low Power Mode"
+    or "LPMD1" and "LPMD0" in the Tegra TRM.
+- nvidia,pull-down-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVDN" in the
+    Tegra TRM.
+- nvidia,pull-up-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVUP" in the
+    Tegra TRM.
+- nvidia,slew-rate-rising: Integer. Controls rising signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVDN_SLWR" in the Tegra TRM.
+- nvidia,slew-rate-falling: Integer. Controls falling signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVUP_SLWF" in the Tegra TRM.
+
+Note that many of these properties are only valid for certain specific pins
+or groups. See the Tegra TRM and various pinmux spreadsheets for complete
+details regarding which groups support which functionality. The Linux pinctrl
+driver may also be a useful reference, since it consolidates, disambiguates,
+and corrects data from all those sources.
+
+Valid values for pin and group names are:
+
+  mux groups:
+
+    These all support nvidia,function, nvidia,tristate, and many support
+    nvidia,pull.
+
+    ata, atb, atc, atd, ate, cdev1, cdev2, crtp, csus, dap1, dap2, dap3, dap4,
+    ddc, dta, dtb, dtc, dtd, dte, dtf, gma, gmb, gmc, gmd, gme, gpu, gpu7,
+    gpv, hdint, i2cp, irrx, irtx, kbca, kbcb, kbcc, kbcd, kbce, kbcf, lcsn,
+    ld0, ld1, ld2, ld3, ld4, ld5, ld6, ld7, ld8, ld9, ld10, ld11, ld12, ld13,
+    ld14, ld15, ld16, ld17, ldc, ldi, lhp0, lhp1, lhp2, lhs, lm0, lm1, lpp,
+    lpw0, lpw1, lpw2, lsc0, lsc1, lsck, lsda, lsdi, lspi, lvp0, lvp1, lvs,
+    owc, pmc, pta, rm, sdb, sdc, sdd, sdio1, slxa, slxc, slxd, slxk, spdi,
+    spdo, spia, spib, spic, spid, spie, spif, spig, spih, uaa, uab, uac, uad,
+    uca, ucb, uda.
+
+  tristate groups:
+
+    These only support nvidia,pull.
+
+    ck32, ddrc, pmca, pmcb, pmcc, pmcd, pmce, xm2c, xm2d, ls, lc, ld17_0,
+    ld19_18, ld21_20, ld23_22.
+
+  drive groups:
+
+    With some exceptions, these support nvidia,high-speed-mode,
+    nvidia,schmitt, nvidia,low-power-mode, nvidia,pull-down-strength,
+    nvidia,pull-up-strength, nvidia,slew-rate-rising, nvidia,slew-rate-falling.
+
+    drive_ao1, drive_ao2, drive_at1, drive_at2, drive_cdev1, drive_cdev2,
+    drive_csus, drive_dap1, drive_dap2, drive_dap3, drive_dap4, drive_dbg,
+    drive_lcd1, drive_lcd2, drive_sdmmc2, drive_sdmmc3, drive_spi, drive_uaa,
+    drive_uab, drive_uart2, drive_uart3, drive_vi1, drive_vi2, drive_xm2a,
+    drive_xm2c, drive_xm2d, drive_xm2clk, drive_sdio1, drive_crt, drive_ddc,
+    drive_gma, drive_gmb, drive_gmc, drive_gmd, drive_gme, drive_owr,
+    drive_uda.
+
+Valid values for nvidia,functions are:
+
+  ahb_clk, apb_clk, audio_sync, crt, dap1, dap2, dap3, dap4, dap5,
+  displaya, displayb, emc_test0_dll, emc_test1_dll, gmi, gmi_int,
+  hdmi, i2cp, i2c1, i2c2, i2c3, ide, irda, kbc, mio, mipi_hs, nand,
+  osc, owr, pcie, plla_out, pllc_out1, pllm_out1, pllp_out2, pllp_out3,
+  pllp_out4, pwm, pwr_intr, pwr_on, rsvd1, rsvd2, rsvd3, rsvd4, rtck,
+  sdio1, sdio2, sdio3, sdio4, sflash, spdif, spi1, spi2, spi2_alt,
+  spi3, spi4, trace, twc, uarta, uartb, uartc, uartd, uarte, ulpi,
+  vi, vi_sensor_clk, xio
+
+Example:
+
+	pinctrl@70000000 {
+		compatible = "nvidia,tegra20-pinmux";
+		reg = < 0x70000014 0x10    /* Tri-state registers */
+			0x70000080 0x20    /* Mux registers */
+			0x700000a0 0x14    /* Pull-up/down registers */
+			0x70000868 0xa8 >; /* Pad control registers */
+	};
+
+Example board file extract:
+
+	pinctrl@70000000 {
+		sdio4_default: sdio4_default {
+			atb {
+				nvidia,pins = "atb", "gma", "gme";
+				nvidia,function = "sdio4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+			};
+		};
+	};
+
+	sdhci@c8000600 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdio4_default>;
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt
new file mode 100644
index 000000000..a62d82d5f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt
@@ -0,0 +1,166 @@
+NVIDIA Tegra210 pinmux controller
+
+Required properties:
+- compatible: "nvidia,tegra210-pinmux"
+- reg: Should contain a list of base address and size pairs for:
+  - first entry: The APB_MISC_GP_*_PADCTRL registers (pad control)
+  - second entry: The PINMUX_AUX_* registers (pinmux)
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Tegra's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, tristate, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function or tristate parameter. For this
+reason, even seemingly boolean values are actually tristates in this binding:
+unspecified, off, or on. Unspecified is represented as an absent property,
+and off/on are represented as integer values 0 and 1.
+
+See the TRM to determine which properties and values apply to each pin/group.
+Macro values for property values are defined in
+include/dt-binding/pinctrl/pinctrl-tegra.h.
+
+Required subnode-properties:
+- nvidia,pins : An array of strings. Each string contains the name of a pin or
+    group. Valid values for these names are listed below.
+
+Optional subnode-properties:
+- nvidia,function: A string containing the name of the function to mux to the
+    pin or group.
+- nvidia,pull: Integer, representing the pull-down/up to apply to the pin.
+    0: none, 1: down, 2: up.
+- nvidia,tristate: Integer.
+    0: drive, 1: tristate.
+- nvidia,enable-input: Integer. Enable the pin's input path.
+    enable :TEGRA_PIN_ENABLE0 and
+    disable or output only: TEGRA_PIN_DISABLE.
+- nvidia,open-drain: Integer.
+    enable: TEGRA_PIN_ENABLE.
+    disable: TEGRA_PIN_DISABLE.
+- nvidia,lock: Integer. Lock the pin configuration against further changes
+    until reset.
+    enable: TEGRA_PIN_ENABLE.
+    disable: TEGRA_PIN_DISABLE.
+- nvidia,io-hv: Integer. Select high-voltage receivers.
+    normal: TEGRA_PIN_DISABLE
+    high: TEGRA_PIN_ENABLE
+- nvidia,high-speed-mode: Integer. Enable high speed mode the pins.
+    normal: TEGRA_PIN_DISABLE
+    high: TEGRA_PIN_ENABLE
+- nvidia,schmitt: Integer. Enables Schmitt Trigger on the input.
+    normal: TEGRA_PIN_DISABLE
+    high: TEGRA_PIN_ENABLE
+- nvidia,drive-type: Integer. Valid range 0...3.
+- nvidia,pull-down-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVDN" in the
+    Tegra TRM.
+- nvidia,pull-up-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVUP" in the
+    Tegra TRM.
+- nvidia,slew-rate-rising: Integer. Controls rising signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVDN_SLWR" in the Tegra TRM.
+- nvidia,slew-rate-falling: Integer. Controls falling signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVUP_SLWF" in the Tegra TRM.
+
+Valid values for pin and group names (nvidia,pin) are:
+
+  Mux groups:
+
+    These correspond to Tegra PINMUX_AUX_* (pinmux) registers. Any property
+    that exists in those registers may be set for the following pin names.
+
+    In Tegra210, many pins also have a dedicated APB_MISC_GP_*_PADCTRL
+    register. Where that is true, and property that exists in that register
+    may also be set on the following pin names.
+
+    als_prox_int_px3, ap_ready_pv5, ap_wake_bt_ph3, ap_wake_nfc_ph7,
+    aud_mclk_pbb0, batt_bcl, bt_rst_ph4, bt_wake_ap_ph5, button_home_py1,
+    button_power_on_px5, button_slide_sw_py0, button_vol_down_px7,
+    button_vol_up_px6, cam1_mclk_ps0, cam1_pwdn_ps7, cam1_strobe_pt1,
+    cam2_mclk_ps1, cam2_pwdn_pt0, cam_af_en_ps5, cam_flash_en_ps6,
+    cam_i2c_scl_ps2, cam_i2c_sda_ps3, cam_rst_ps4cam_rst_ps4, clk_32k_in,
+    clk_32k_out_py5, clk_req, core_pwr_req, cpu_pwr_req, dap1_din_pb1,
+    dap1_dout_pb2, dap1_fs_pb0, dap1_sclk_pb3, dap2_din_paa2, dap2_dout_paa3,
+    dap2_fs_paa0, dap2_sclk_paa1, dap4_din_pj5, dap4_dout_pj6, dap4_fs_pj4,
+    dap4_sclk_pj7, dmic1_clk_pe0, dmic1_dat_pe1, dmic2_clk_pe2, dmic2_dat_pe3,
+    dmic3_clk_pe4, dmic3_dat_pe5, dp_hpd0_pcc6, dvfs_clk_pbb2, dvfs_pwm_pbb1,
+    gen1_i2c_scl_pj1, gen1_i2c_sda_pj0, gen2_i2c_scl_pj2, gen2_i2c_sda_pj3,
+    gen3_i2c_scl_pf0, gen3_i2c_sda_pf1, gpio_x1_aud_pbb3, gpio_x3_aud_pbb4,
+    gps_en_pi2, gps_rst_pi3, hdmi_cec_pcc0, hdmi_int_dp_hpd_pcc1, jtag_rtck,
+    lcd_bl_en_pv1, lcd_bl_pwm_pv0, lcd_gpio1_pv3, lcd_gpio2_pv4, lcd_rst_pv2,
+    lcd_te_py2, modem_wake_ap_px0, motion_int_px2, nfc_en_pi0, nfc_int_pi1,
+    pa6, pcc7, pe6, pe7, pex_l0_clkreq_n_pa1, pex_l0_rst_n_pa0,
+    pex_l1_clkreq_n_pa4, pex_l1_rst_n_pa3, pex_wake_n_pa2, ph6, pk0, pk1, pk2,
+    pk3, pk4, pk5, pk6, pk7, pl0, pl1, pwr_i2c_scl_py3, pwr_i2c_sda_py4,
+    pwr_int_n, pz0, pz1, pz2, pz3, pz4, pz5, qspi_cs_n_pee1, qspi_io0_pee2,
+    qspi_io1_pee3, qspi_io2_pee4, qspi_io3_pee5, qspi_sck_pee0,
+    sata_led_active_pa5, sdmmc1_clk_pm0, sdmmc1_cmd_pm1, sdmmc1_dat0_pm5,
+    sdmmc1_dat1_pm4, sdmmc1_dat2_pm3, sdmmc1_dat3_pm2, sdmmc3_clk_pp0,
+    sdmmc3_cmd_pp1, sdmmc3_dat0_pp5, sdmmc3_dat1_pp4, sdmmc3_dat2_pp3,
+    sdmmc3_dat3_pp2, shutdown, spdif_in_pcc3, spdif_out_pcc2, spi1_cs0_pc3,
+    spi1_cs1_pc4, spi1_miso_pc1, spi1_mosi_pc0, spi1_sck_pc2, spi2_cs0_pb7,
+    spi2_cs1_pdd0, spi2_miso_pb5, spi2_mosi_pb4, spi2_sck_pb6, spi4_cs0_pc6,
+    spi4_miso_pd0, spi4_mosi_pc7, spi4_sck_pc5, temp_alert_px4, touch_clk_pv7,
+    touch_int_px1, touch_rst_pv6, uart1_cts_pu3, uart1_rts_pu2, uart1_rx_pu1,
+    uart1_tx_pu0, uart2_cts_pg3, uart2_rts_pg2, uart2_rx_pg1, uart2_tx_pg0,
+    uart3_cts_pd4, uart3_rts_pd3, uart3_rx_pd2, uart3_tx_pd1, uart4_cts_pi7,
+    uart4_rts_pi6, uart4_rx_pi5, uart4_tx_pi4, usb_vbus_en0_pcc4,
+    usb_vbus_en1_pcc5, wifi_en_ph0, wifi_rst_ph1, wifi_wake_ap_ph2
+
+  Drive groups:
+
+    These correspond to the Tegra APB_MISC_GP_*_PADCTRL (pad control)
+    registers. Note that where one of these registers controls a single pin
+    for which a PINMUX_AUX_* exists, see the list above for the pin name to
+    use when configuring the pinmux.
+
+    pa6, pcc7, pe6, pe7, ph6, pk0, pk1, pk2, pk3, pk4, pk5, pk6, pk7, pl0, pl1,
+    pz0, pz1, pz2, pz3, pz4, pz5, sdmmc1, sdmmc2, sdmmc3, sdmmc4
+
+Valid values for nvidia,functions are:
+
+    aud, bcl, blink, ccla, cec, cldvfs, clk, core, cpu, displaya, displayb,
+    dmic1, dmic2, dmic3, dp, dtv, extperiph3, i2c1, i2c2, i2c3, i2cpmu, i2cvi,
+    i2s1, i2s2, i2s3, i2s4a, i2s4b, i2s5a, i2s5b, iqc0, iqc1, jtag, pe, pe0,
+    pe1, pmi, pwm0, pwm1, pwm2, pwm3, qspi, rsvd0, rsvd1, rsvd2, rsvd3, sata,
+    sdmmc1, sdmmc3, shutdown, soc, sor0, sor1, spdif, spi1, spi2, spi3, spi4,
+    sys, touch, uart, uarta, uartb, uartc, uartd, usb, vgp1, vgp2, vgp3, vgp4,
+    vgp5, vgp6, vimclk, vimclk2
+
+Example:
+
+	pinmux: pinmux@70000800 {
+		compatible = "nvidia,tegra210-pinmux";
+		reg = <0x0 0x700008d4 0x0 0x2a8>, /* Pad control registers */
+		      <0x0 0x70003000 0x0 0x1000>; /* Mux registers */
+
+		pinctrl-names = "boot";
+		pinctrl-0 = <&state_boot>;
+
+		state_boot: pinmux {
+			gen1_i2c_scl_pj1 {
+				nvidia,pins = "gen1_i2c_scl_pj1",
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,io-hv = <TEGRA_PIN_ENABLE>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt
new file mode 100644
index 000000000..0e6354c11
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt
@@ -0,0 +1,144 @@
+NVIDIA Tegra30 pinmux controller
+
+The Tegra30 pinctrl binding is very similar to the Tegra20 pinctrl binding,
+as described in nvidia,tegra20-pinmux.txt. In fact, this document assumes
+that binding as a baseline, and only documents the differences between the
+two bindings.
+
+Required properties:
+- compatible: "nvidia,tegra30-pinmux"
+- reg: Should contain the register physical address and length for each of
+  the pad control and mux registers.
+
+Tegra30 adds the following optional properties for pin configuration subnodes:
+- nvidia,enable-input: Integer. Enable the pin's input path. 0: no, 1: yes.
+- nvidia,open-drain: Integer. Enable open drain mode. 0: no, 1: yes.
+- nvidia,lock: Integer. Lock the pin configuration against further changes
+    until reset. 0: no, 1: yes.
+- nvidia,io-reset: Integer. Reset the IO path. 0: no, 1: yes.
+
+As with Tegra20, see the Tegra TRM for complete details regarding which groups
+support which functionality.
+
+Valid values for pin and group names are:
+
+  per-pin mux groups:
+
+    These all support nvidia,function, nvidia,tristate, nvidia,pull,
+    nvidia,enable-input, nvidia,lock. Some support nvidia,open-drain,
+    nvidia,io-reset.
+
+    clk_32k_out_pa0, uart3_cts_n_pa1, dap2_fs_pa2, dap2_sclk_pa3,
+    dap2_din_pa4, dap2_dout_pa5, sdmmc3_clk_pa6, sdmmc3_cmd_pa7, gmi_a17_pb0,
+    gmi_a18_pb1, lcd_pwr0_pb2, lcd_pclk_pb3, sdmmc3_dat3_pb4, sdmmc3_dat2_pb5,
+    sdmmc3_dat1_pb6, sdmmc3_dat0_pb7, uart3_rts_n_pc0, lcd_pwr1_pc1,
+    uart2_txd_pc2, uart2_rxd_pc3, gen1_i2c_scl_pc4, gen1_i2c_sda_pc5,
+    lcd_pwr2_pc6, gmi_wp_n_pc7, sdmmc3_dat5_pd0, sdmmc3_dat4_pd1, lcd_dc1_pd2,
+    sdmmc3_dat6_pd3, sdmmc3_dat7_pd4, vi_d1_pd5, vi_vsync_pd6, vi_hsync_pd7,
+    lcd_d0_pe0, lcd_d1_pe1, lcd_d2_pe2, lcd_d3_pe3, lcd_d4_pe4, lcd_d5_pe5,
+    lcd_d6_pe6, lcd_d7_pe7, lcd_d8_pf0, lcd_d9_pf1, lcd_d10_pf2, lcd_d11_pf3,
+    lcd_d12_pf4, lcd_d13_pf5, lcd_d14_pf6, lcd_d15_pf7, gmi_ad0_pg0,
+    gmi_ad1_pg1, gmi_ad2_pg2, gmi_ad3_pg3, gmi_ad4_pg4, gmi_ad5_pg5,
+    gmi_ad6_pg6, gmi_ad7_pg7, gmi_ad8_ph0, gmi_ad9_ph1, gmi_ad10_ph2,
+    gmi_ad11_ph3, gmi_ad12_ph4, gmi_ad13_ph5, gmi_ad14_ph6, gmi_ad15_ph7,
+    gmi_wr_n_pi0, gmi_oe_n_pi1, gmi_dqs_pi2, gmi_cs6_n_pi3, gmi_rst_n_pi4,
+    gmi_iordy_pi5, gmi_cs7_n_pi6, gmi_wait_pi7, gmi_cs0_n_pj0, lcd_de_pj1,
+    gmi_cs1_n_pj2, lcd_hsync_pj3, lcd_vsync_pj4, uart2_cts_n_pj5,
+    uart2_rts_n_pj6, gmi_a16_pj7, gmi_adv_n_pk0, gmi_clk_pk1, gmi_cs4_n_pk2,
+    gmi_cs2_n_pk3, gmi_cs3_n_pk4, spdif_out_pk5, spdif_in_pk6, gmi_a19_pk7,
+    vi_d2_pl0, vi_d3_pl1, vi_d4_pl2, vi_d5_pl3, vi_d6_pl4, vi_d7_pl5,
+    vi_d8_pl6, vi_d9_pl7, lcd_d16_pm0, lcd_d17_pm1, lcd_d18_pm2, lcd_d19_pm3,
+    lcd_d20_pm4, lcd_d21_pm5, lcd_d22_pm6, lcd_d23_pm7, dap1_fs_pn0,
+    dap1_din_pn1, dap1_dout_pn2, dap1_sclk_pn3, lcd_cs0_n_pn4, lcd_sdout_pn5,
+    lcd_dc0_pn6, hdmi_int_pn7, ulpi_data7_po0, ulpi_data0_po1, ulpi_data1_po2,
+    ulpi_data2_po3, ulpi_data3_po4, ulpi_data4_po5, ulpi_data5_po6,
+    ulpi_data6_po7, dap3_fs_pp0, dap3_din_pp1, dap3_dout_pp2, dap3_sclk_pp3,
+    dap4_fs_pp4, dap4_din_pp5, dap4_dout_pp6, dap4_sclk_pp7, kb_col0_pq0,
+    kb_col1_pq1, kb_col2_pq2, kb_col3_pq3, kb_col4_pq4, kb_col5_pq5,
+    kb_col6_pq6, kb_col7_pq7, kb_row0_pr0, kb_row1_pr1, kb_row2_pr2,
+    kb_row3_pr3, kb_row4_pr4, kb_row5_pr5, kb_row6_pr6, kb_row7_pr7,
+    kb_row8_ps0, kb_row9_ps1, kb_row10_ps2, kb_row11_ps3, kb_row12_ps4,
+    kb_row13_ps5, kb_row14_ps6, kb_row15_ps7, vi_pclk_pt0, vi_mclk_pt1,
+    vi_d10_pt2, vi_d11_pt3, vi_d0_pt4, gen2_i2c_scl_pt5, gen2_i2c_sda_pt6,
+    sdmmc4_cmd_pt7, pu0, pu1, pu2, pu3, pu4, pu5, pu6, jtag_rtck_pu7, pv0,
+    pv1, pv2, pv3, ddc_scl_pv4, ddc_sda_pv5, crt_hsync_pv6, crt_vsync_pv7,
+    lcd_cs1_n_pw0, lcd_m1_pw1, spi2_cs1_n_pw2, spi2_cs2_n_pw3, clk1_out_pw4,
+    clk2_out_pw5, uart3_txd_pw6, uart3_rxd_pw7, spi2_mosi_px0, spi2_miso_px1,
+    spi2_sck_px2, spi2_cs0_n_px3, spi1_mosi_px4, spi1_sck_px5, spi1_cs0_n_px6,
+    spi1_miso_px7, ulpi_clk_py0, ulpi_dir_py1, ulpi_nxt_py2, ulpi_stp_py3,
+    sdmmc1_dat3_py4, sdmmc1_dat2_py5, sdmmc1_dat1_py6, sdmmc1_dat0_py7,
+    sdmmc1_clk_pz0, sdmmc1_cmd_pz1, lcd_sdin_pz2, lcd_wr_n_pz3, lcd_sck_pz4,
+    sys_clk_req_pz5, pwr_i2c_scl_pz6, pwr_i2c_sda_pz7, sdmmc4_dat0_paa0,
+    sdmmc4_dat1_paa1, sdmmc4_dat2_paa2, sdmmc4_dat3_paa3, sdmmc4_dat4_paa4,
+    sdmmc4_dat5_paa5, sdmmc4_dat6_paa6, sdmmc4_dat7_paa7, pbb0,
+    cam_i2c_scl_pbb1, cam_i2c_sda_pbb2, pbb3, pbb4, pbb5, pbb6, pbb7,
+    cam_mclk_pcc0, pcc1, pcc2, sdmmc4_rst_n_pcc3, sdmmc4_clk_pcc4,
+    clk2_req_pcc5, pex_l2_rst_n_pcc6, pex_l2_clkreq_n_pcc7,
+    pex_l0_prsnt_n_pdd0, pex_l0_rst_n_pdd1, pex_l0_clkreq_n_pdd2,
+    pex_wake_n_pdd3, pex_l1_prsnt_n_pdd4, pex_l1_rst_n_pdd5,
+    pex_l1_clkreq_n_pdd6, pex_l2_prsnt_n_pdd7, clk3_out_pee0, clk3_req_pee1,
+    clk1_req_pee2, hdmi_cec_pee3, clk_32k_in, core_pwr_req, cpu_pwr_req, owr,
+    pwr_int_n.
+
+  drive groups:
+
+    These all support nvidia,pull-down-strength, nvidia,pull-up-strength,
+    nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all
+    support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode.
+
+    ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, cec, crt, csus, dap1,
+    dap2, dap3, dap4, dbg, ddc, dev3, gma, gmb, gmc, gmd, gme, gmf, gmg,
+    gmh, gpv, lcd1, lcd2, owr, sdio1, sdio2, sdio3, spi, uaa, uab, uart2,
+    uart3, uda, vi1.
+
+Valid values for nvidia,functions are:
+
+  blink, cec, clk_12m_out, clk_32k_in, core_pwr_req, cpu_pwr_req, crt,
+  dap, ddr, dev3, displaya, displayb, dtv, extperiph1, extperiph2,
+  extperiph3, gmi, gmi_alt, hda, hdcp, hdmi, hsi, i2c1, i2c2, i2c3,
+  i2c4, i2cpwr, i2s0, i2s1, i2s2, i2s3, i2s4, invalid, kbc, mio, nand,
+  nand_alt, owr, pcie, pwm0, pwm1, pwm2, pwm3, pwr_int_n, rsvd1, rsvd2,
+  rsvd3, rsvd4, rtck, sata, sdmmc1, sdmmc2, sdmmc3, sdmmc4, spdif, spi1,
+  spi2, spi2_alt, spi3, spi4, spi5, spi6, sysclk, test, trace, uarta,
+  uartb, uartc, uartd, uarte, ulpi, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6,
+  vi, vi_alt1, vi_alt2, vi_alt3
+
+Example:
+
+	pinctrl@70000000 {
+		compatible = "nvidia,tegra30-pinmux";
+		reg = < 0x70000868 0xd0     /* Pad control registers */
+			0x70003000 0x3e0 >; /* Mux registers */
+	};
+
+Example board file extract:
+
+	pinctrl@70000000 {
+		sdmmc4_default: pinmux {
+			sdmmc4_clk_pcc4 {
+				nvidia,pins =	"sdmmc4_clk_pcc4",
+						"sdmmc4_rst_n_pcc3";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <0>;
+				nvidia,tristate = <0>;
+			};
+			sdmmc4_dat0_paa0 {
+				nvidia,pins =	"sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <2>;
+				nvidia,tristate = <0>;
+			};
+		};
+	};
+
+	sdhci@78000400 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc4_default>;
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
new file mode 100644
index 000000000..b73c96d24
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
@@ -0,0 +1,236 @@
+== Introduction ==
+
+Hardware modules that control pin multiplexing or configuration parameters
+such as pull-up/down, tri-state, drive-strength etc are designated as pin
+controllers. Each pin controller must be represented as a node in device tree,
+just like any other hardware module.
+
+Hardware modules whose signals are affected by pin configuration are
+designated client devices. Again, each client device must be represented as a
+node in device tree, just like any other hardware module.
+
+For a client device to operate correctly, certain pin controllers must
+set up certain specific pin configurations. Some client devices need a
+single static pin configuration, e.g. set up during initialization. Others
+need to reconfigure pins at run-time, for example to tri-state pins when the
+device is inactive. Hence, each client device can define a set of named
+states. The number and names of those states is defined by the client device's
+own binding.
+
+The common pinctrl bindings defined in this file provide an infrastructure
+for client device device tree nodes to map those state names to the pin
+configuration used by those states.
+
+Note that pin controllers themselves may also be client devices of themselves.
+For example, a pin controller may set up its own "active" state when the
+driver loads. This would allow representing a board's static pin configuration
+in a single place, rather than splitting it across multiple client device
+nodes. The decision to do this or not somewhat rests with the author of
+individual board device tree files, and any requirements imposed by the
+bindings for the individual client devices in use by that board, i.e. whether
+they require certain specific named states for dynamic pin configuration.
+
+== Pinctrl client devices ==
+
+For each client device individually, every pin state is assigned an integer
+ID. These numbers start at 0, and are contiguous. For each state ID, a unique
+property exists to define the pin configuration. Each state may also be
+assigned a name. When names are used, another property exists to map from
+those names to the integer IDs.
+
+Each client device's own binding determines the set of states that must be
+defined in its device tree node, and whether to define the set of state
+IDs that must be provided, or whether to define the set of state names that
+must be provided.
+
+Required properties:
+pinctrl-0:	List of phandles, each pointing at a pin configuration
+		node. These referenced pin configuration nodes must be child
+		nodes of the pin controller that they configure. Multiple
+		entries may exist in this list so that multiple pin
+		controllers may be configured, or so that a state may be built
+		from multiple nodes for a single pin controller, each
+		contributing part of the overall configuration. See the next
+		section of this document for details of the format of these
+		pin configuration nodes.
+
+		In some cases, it may be useful to define a state, but for it
+		to be empty. This may be required when a common IP block is
+		used in an SoC either without a pin controller, or where the
+		pin controller does not affect the HW module in question. If
+		the binding for that IP block requires certain pin states to
+		exist, they must still be defined, but may be left empty.
+
+Optional properties:
+pinctrl-1:	List of phandles, each pointing at a pin configuration
+		node within a pin controller.
+...
+pinctrl-n:	List of phandles, each pointing at a pin configuration
+		node within a pin controller.
+pinctrl-names:	The list of names to assign states. List entry 0 defines the
+		name for integer state ID 0, list entry 1 for state ID 1, and
+		so on.
+
+For example:
+
+	/* For a client device requiring named states */
+	device {
+		pinctrl-names = "active", "idle";
+		pinctrl-0 = <&state_0_node_a>;
+		pinctrl-1 = <&state_1_node_a &state_1_node_b>;
+	};
+
+	/* For the same device if using state IDs */
+	device {
+		pinctrl-0 = <&state_0_node_a>;
+		pinctrl-1 = <&state_1_node_a &state_1_node_b>;
+	};
+
+	/*
+	 * For an IP block whose binding supports pin configuration,
+	 * but in use on an SoC that doesn't have any pin control hardware
+	 */
+	device {
+		pinctrl-names = "active", "idle";
+		pinctrl-0 = <>;
+		pinctrl-1 = <>;
+	};
+
+== Pin controller devices ==
+
+Pin controller devices should contain the pin configuration nodes that client
+devices reference.
+
+For example:
+
+	pincontroller {
+		... /* Standard DT properties for the device itself elided */
+
+		state_0_node_a {
+			...
+		};
+		state_1_node_a {
+			...
+		};
+		state_1_node_b {
+			...
+		};
+	}
+
+The contents of each of those pin configuration child nodes is defined
+entirely by the binding for the individual pin controller device. There
+exists no common standard for this content.
+
+The pin configuration nodes need not be direct children of the pin controller
+device; they may be grandchildren, for example. Whether this is legal, and
+whether there is any interaction between the child and intermediate parent
+nodes, is again defined entirely by the binding for the individual pin
+controller device.
+
+== Generic pin multiplexing node content ==
+
+pin multiplexing nodes:
+
+function		- the mux function to select
+groups			- the list of groups to select with this function
+			  (either this or "pins" must be specified)
+pins			- the list of pins to select with this function (either
+			  this or "groups" must be specified)
+
+Example:
+
+state_0_node_a {
+	uart0 {
+		function = "uart0";
+		groups = "u0rxtx", "u0rtscts";
+	};
+};
+state_1_node_a {
+	spi0 {
+		function = "spi0";
+		groups = "spi0pins";
+	};
+};
+state_2_node_a {
+	function = "i2c0";
+	pins = "mfio29", "mfio30";
+};
+
+== Generic pin configuration node content ==
+
+Many data items that are represented in a pin configuration node are common
+and generic. Pin control bindings should use the properties defined below
+where they are applicable; not all of these properties are relevant or useful
+for all hardware or binding structures. Each individual binding document
+should state which of these generic properties, if any, are used, and the
+structure of the DT nodes that contain these properties.
+
+Supported generic properties are:
+
+pins			- the list of pins that properties in the node
+			  apply to (either this or "group" has to be
+			  specified)
+group			- the group to apply the properties to, if the driver
+			  supports configuration of whole groups rather than
+			  individual pins (either this or "pins" has to be
+			  specified)
+bias-disable		- disable any pin bias
+bias-high-impedance	- high impedance mode ("third-state", "floating")
+bias-bus-hold		- latch weakly
+bias-pull-up		- pull up the pin
+bias-pull-down		- pull down the pin
+bias-pull-pin-default	- use pin-default pull state
+drive-push-pull		- drive actively high and low
+drive-open-drain	- drive with open drain
+drive-open-source	- drive with open source
+drive-strength		- sink or source at most X mA
+input-enable		- enable input on pin (no effect on output)
+input-disable		- disable input on pin (no effect on output)
+input-schmitt-enable	- enable schmitt-trigger mode
+input-schmitt-disable	- disable schmitt-trigger mode
+input-debounce		- debounce mode with debound time X
+power-source		- select between different power supplies
+low-power-enable	- enable low power mode
+low-power-disable	- disable low power mode
+output-low		- set the pin to output mode with low level
+output-high		- set the pin to output mode with high level
+slew-rate		- set the slew rate
+
+For example:
+
+state_0_node_a {
+	cts_rxd {
+		pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+		bias-pull-up;
+	};
+};
+state_1_node_a {
+	rts_txd {
+		pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */
+		output-high;
+	};
+};
+state_2_node_a {
+	foo {
+		group = "foo-group";
+		bias-pull-up;
+	};
+};
+
+Some of the generic properties take arguments. For those that do, the
+arguments are described below.
+
+- pins takes a list of pin names or IDs as a required argument. The specific
+  binding for the hardware defines:
+  - Whether the entries are integers or strings, and their meaning.
+
+- bias-pull-up, -down and -pin-default take as optional argument on hardware
+  supporting it the pull strength in Ohm. bias-disable will disable the pull.
+
+- drive-strength takes as argument the target strength in mA.
+
+- input-debounce takes the debounce time in usec as argument
+  or 0 to disable debouncing
+
+More in-depth documentation on these parameters can be found in
+<include/linux/pinctrl/pinconf-generic.h>
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt
new file mode 100644
index 000000000..5868a0f72
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt
@@ -0,0 +1,145 @@
+* Mediatek MT65XX Pin Controller
+
+The Mediatek's Pin controller is used to control SoC pins.
+
+Required properties:
+- compatible: value should be either of the following.
+    (a) "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl.
+- mediatek,pctl-regmap: Should be a phandle of the syscfg node.
+- pins-are-numbered: Specify the subnodes are using numbered pinmux to
+  specify pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+  binding is used, the amount of cells must be specified as 2. See the below
+  mentioned gpio binding representation for description of particular cells.
+
+	Eg: <&pio 6 0>
+	<[phandle of the gpio controller node]
+	[line number within the gpio controller]
+	[flags]>
+
+	Values for gpio specifier:
+	- Line number: is a value between 0 to 202.
+	- Flags:  bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
+            Only the following flags are supported:
+            0 - GPIO_ACTIVE_HIGH
+            1 - GPIO_ACTIVE_LOW
+- reg: physicall address base for EINT registers
+- interrupt-controller: Marks the device node as an interrupt controller
+- #interrupt-cells: Should be two.
+- interrupts : The interrupt outputs from the controller.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices.
+
+Subnode format
+A pinctrl node should contain at least one subnodes representing the
+pinctrl groups available on the machine. Each subnode will list the
+pins it needs, and how they should be configured, with regard to muxer
+configuration, pullups, drive strength, input enable/disable and input schmitt.
+
+    node {
+	pinmux = <PIN_NUMBER_PINMUX>;
+	GENERIC_PINCONFIG;
+    };
+
+Required properties:
+- pinmux: integer array, represents gpio pin number and mux setting.
+    Supported pin number and mux varies for different SoCs, and are defined
+    as macros in boot/dts/<soc>-pinfunc.h directly.
+
+Optional properties:
+- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
+    bias-pull-down, bias-pull-up, input-enable, input-disable, output-low, output-high,
+    input-schmitt-enable, input-schmitt-disable and drive-strength are valid.
+
+    Some special pins have extra pull up strength, there are R0 and R1 pull-up
+    resistors available, but for user, it's only need to set R1R0 as 00, 01, 10 or 11.
+    So when config bias-pull-up, it support arguments for those special pins.
+    Some macros have been defined for this usage, such as MTK_PUPD_SET_R1R0_00.
+    See dt-bindings/pinctrl/mt65xx.h.
+
+    When config drive-strength, it can support some arguments, such as
+    MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h.
+
+Examples:
+
+#include "mt8135-pinfunc.h"
+
+...
+{
+	syscfg_pctl_a: syscfg_pctl_a@10005000 {
+		compatible = "mediatek,mt8135-pctl-a-syscfg", "syscon";
+		reg = <0 0x10005000 0 0x1000>;
+	};
+
+	syscfg_pctl_b: syscfg_pctl_b@1020C020 {
+		compatible = "mediatek,mt8135-pctl-b-syscfg", "syscon";
+		reg = <0 0x1020C020 0 0x1000>;
+	};
+
+	pinctrl@01c20800 {
+		compatible = "mediatek,mt8135-pinctrl";
+		reg = <0 0x1000B000 0 0x1000>;
+		mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>;
+		pins-are-numbered;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+
+		i2c0_pins_a: i2c0@0 {
+			pins1 {
+				pinmux = <MT8135_PIN_100_SDA0__FUNC_SDA0>,
+					 <MT8135_PIN_101_SCL0__FUNC_SCL0>;
+				bias-disable;
+			};
+		};
+
+		i2c1_pins_a: i2c1@0 {
+			pins {
+				pinmux = <MT8135_PIN_195_SDA1__FUNC_SDA1>,
+					 <MT8135_PIN_196_SCL1__FUNC_SCL1>;
+				bias-pull-up = <55>;
+			};
+		};
+
+		i2c2_pins_a: i2c2@0 {
+			pins1 {
+				pinmux = <MT8135_PIN_193_SDA2__FUNC_SDA2>;
+				bias-pull-down;
+			};
+
+			pins2 {
+				pinmux = <MT8135_PIN_49_WATCHDOG__FUNC_GPIO49>;
+				bias-pull-up;
+			};
+		};
+
+		i2c3_pins_a: i2c3@0 {
+			pins1 {
+				pinmux = <MT8135_PIN_40_DAC_CLK__FUNC_GPIO40>,
+					 <MT8135_PIN_41_DAC_WS__FUNC_GPIO41>;
+				bias-pull-up = <55>;
+			};
+
+			pins2 {
+				pinmux = <MT8135_PIN_35_SCL3__FUNC_SCL3>,
+					 <MT8135_PIN_36_SDA3__FUNC_SDA3>;
+				output-low;
+				bias-pull-up = <55>;
+			};
+
+			pins3 {
+				pinmux = <MT8135_PIN_57_JTCK__FUNC_GPIO57>,
+					 <MT8135_PIN_60_JTDI__FUNC_JTDI>;
+				drive-strength = <32>;
+			};
+		};
+
+		...
+	}
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt
new file mode 100644
index 000000000..caf297bee
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt
@@ -0,0 +1,96 @@
+Palmas Pincontrol bindings
+
+The pins of Palmas device can be set on different option and provides
+the configuration for Pull UP/DOWN, open drain etc.
+
+Required properties:
+- compatible: It must be one of following:
+  - "ti,palmas-pinctrl" for Palma series of the pincontrol.
+  - "ti,tps65913-pinctrl" for Palma series device TPS65913.
+  - "ti,tps80036-pinctrl" for Palma series device TPS80036.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Palmas's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+list of pins. This configuration can include the mux function to select on
+those pin(s), and various pin configuration parameters, such as pull-up,
+open drain.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+Optional properties:
+- ti,palmas-enable-dvfs1: Enable DVFS1. Configure pins for DVFS1 mode.
+	Selection primary or secondary function associated to I2C2_SCL_SCE,
+	I2C2_SDA_SDO pin/pad for DVFS1 interface
+- ti,palmas-enable-dvfs2: Enable DVFS2. Configure pins for DVFS2 mode.
+	Selection primary or secondary function associated to GPADC_START
+	and SYSEN2 pin/pad for DVFS2 interface
+
+This binding uses the following generic properties as defined in
+pinctrl-bindings.txt:
+
+Required: pins
+Options: function, bias-disable, bias-pull-up, bias-pull-down,
+	 drive-open-drain.
+
+Note that many of these properties are only valid for certain specific pins.
+See the Palmas device datasheet for complete details regarding which pins
+support which functionality.
+
+Valid values for pin names are:
+	gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7, gpio8, gpio9,
+	gpio10, gpio11, gpio12, gpio13, gpio14, gpio15, vac, powergood,
+	nreswarm, pwrdown, gpadc_start, reset_in, nsleep, enable1, enable2,
+	int.
+
+Valid value of function names are:
+	gpio, led, pwm, regen, sysen, clk32kgaudio, id, vbus_det, chrg_det,
+	vac, vacok, powergood, usb_psel, msecure, pwrhold, int, nreswarm,
+	simrsto, simrsti, low_vbat, wireless_chrg1, rcm, pwrdown, gpadc_start,
+	reset_in, nsleep, enable.
+
+There are 4 special functions: opt0, opt1, opt2 and opt3. If any of these
+functions is selected then directly pins register will be written with 0, 1, 2
+or 3 respectively if it is valid for that pins or list of pins.
+
+Example:
+	palmas: tps65913 {
+		....
+		pinctrl {
+			compatible = "ti,tps65913-pinctrl";
+			ti,palmas-enable-dvfs1;
+			pinctrl-names = "default";
+			pinctrl-0 = <&palmas_pins_state>;
+
+			palmas_pins_state: pinmux {
+				gpio0 {
+					pins = "gpio0";
+					function = "id";
+					bias-pull-up;
+				};
+
+				vac {
+					pins = "vac";
+					function = "vacok";
+					bias-pull-down;
+				};
+
+				gpio5 {
+					pins = "gpio5";
+					function = "opt0";
+					drive-open-drain = <1>;
+				};
+			};
+		};
+		....
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
new file mode 100644
index 000000000..66dcaa9ef
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt
@@ -0,0 +1,252 @@
+One-register-per-pin type device tree based pinctrl driver
+
+Required properties:
+- compatible : "pinctrl-single" or "pinconf-single".
+  "pinctrl-single" means that pinconf isn't supported.
+  "pinconf-single" means that generic pinconf is supported.
+
+- reg : offset and length of the register set for the mux registers
+
+- pinctrl-single,register-width : pinmux register access width in bits
+
+- pinctrl-single,function-mask : mask of allowed pinmux function bits
+  in the pinmux register
+
+Optional properties:
+- pinctrl-single,function-off : function off mode for disabled state if
+  available and same for all registers; if not specified, disabling of
+  pin functions is ignored
+
+- pinctrl-single,bit-per-mux : boolean to indicate that one register controls
+  more than one pin, for which "pinctrl-single,function-mask" property specifies
+ position mask of pin.
+
+- pinctrl-single,drive-strength : array of value that are used to configure
+  drive strength in the pinmux register. They're value of drive strength
+  current and drive strength mask.
+
+		/* drive strength current, mask */
+		pinctrl-single,power-source = <0x30 0xf0>;
+
+- pinctrl-single,bias-pullup : array of value that are used to configure the
+  input bias pullup in the pinmux register.
+
+		/* input, enabled pullup bits, disabled pullup bits, mask */
+		pinctrl-single,bias-pullup = <0 1 0 1>;
+
+- pinctrl-single,bias-pulldown : array of value that are used to configure the
+  input bias pulldown in the pinmux register.
+
+		/* input, enabled pulldown bits, disabled pulldown bits, mask */
+		pinctrl-single,bias-pulldown = <2 2 0 2>;
+
+  * Two bits to control input bias pullup and pulldown: User should use
+    pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. One bit means
+    pullup, and the other one bit means pulldown.
+  * Three bits to control input bias enable, pullup and pulldown. User should
+    use pinctrl-single,bias-pullup & pinctrl-single,bias-pulldown. Input bias
+    enable bit should be included in pullup or pulldown bits.
+  * Although driver could set PIN_CONFIG_BIAS_DISABLE, there's no property as
+    pinctrl-single,bias-disable. Because pinctrl single driver could implement
+    it by calling pulldown, pullup disabled.
+
+- pinctrl-single,input-schmitt : array of value that are used to configure
+  input schmitt in the pinmux register. In some silicons, there're two input
+  schmitt value (rising-edge & falling-edge) in the pinmux register.
+
+		/* input schmitt value, mask */
+		pinctrl-single,input-schmitt = <0x30 0x70>;
+
+- pinctrl-single,input-schmitt-enable : array of value that are used to
+  configure input schmitt enable or disable in the pinmux register.
+
+		/* input, enable bits, disable bits, mask */
+		pinctrl-single,input-schmitt-enable = <0x30 0x40 0 0x70>;
+
+- pinctrl-single,low-power-mode : array of value that are used to configure
+  low power mode of this pin. For some silicons, the low power mode will
+  control the output of the pin when the pad including the pin enter low
+  power mode.
+		/* low power mode value, mask */
+		pinctrl-single,low-power-mode = <0x288 0x388>;
+
+- pinctrl-single,gpio-range : list of value that are used to configure a GPIO
+  range. They're value of subnode phandle, pin base in pinctrl device, pin
+  number in this range, GPIO function value of this GPIO range.
+  The number of parameters is depend on #pinctrl-single,gpio-range-cells
+  property.
+
+		/* pin base, nr pins & gpio function */
+		pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1>;
+
+- interrupt-controller : standard interrupt controller binding if using
+  interrupts for wake-up events for example. In this case pinctrl-single
+  is set up as a chained interrupt controller and the wake-up interrupts
+  can be requested by the drivers using request_irq().
+
+- #interrupt-cells : standard interrupt binding if using interrupts
+
+This driver assumes that there is only one register for each pin (unless the
+pinctrl-single,bit-per-mux is set), and uses the common pinctrl bindings as
+specified in the pinctrl-bindings.txt document in this directory.
+
+The pin configuration nodes for pinctrl-single are specified as pinctrl
+register offset and value pairs using pinctrl-single,pins. Only the bits
+specified in pinctrl-single,function-mask are updated. For example, setting
+a pin for a device could be done with:
+
+	pinctrl-single,pins = <0xdc 0x118>;
+
+Where 0xdc is the offset from the pinctrl register base address for the
+device pinctrl register, and 0x118 contains the desired value of the
+pinctrl register. See the device example and static board pins example
+below for more information.
+
+In case when one register changes more than one pin's mux the
+pinctrl-single,bits need to be used which takes three parameters:
+
+	pinctrl-single,bits = <0xdc 0x18 0xff>;
+
+Where 0xdc is the offset from the pinctrl register base address for the
+device pinctrl register, 0x18 is the desired value, and 0xff is the sub mask to
+be used when applying this change to the register.
+
+
+Optional sub-node: In case some pins could be configured as GPIO in the pinmux
+register, those pins could be defined as a GPIO range. This sub-node is required
+by pinctrl-single,gpio-range property.
+
+Required properties in sub-node:
+- #pinctrl-single,gpio-range-cells : the number of parameters after phandle in
+  pinctrl-single,gpio-range property.
+
+	range: gpio-range {
+		#pinctrl-single,gpio-range-cells = <3>;
+	};
+
+
+Example:
+
+/* SoC common file */
+
+/* first controller instance for pins in core domain */
+pmx_core: pinmux@4a100040 {
+	compatible = "pinctrl-single";
+	reg = <0x4a100040 0x0196>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	#interrupt-cells = <1>;
+	interrupt-controller;
+	pinctrl-single,register-width = <16>;
+	pinctrl-single,function-mask = <0xffff>;
+};
+
+/* second controller instance for pins in wkup domain */
+pmx_wkup: pinmux@4a31e040 {
+	compatible = "pinctrl-single";
+	reg = <0x4a31e040 0x0038>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	#interrupt-cells = <1>;
+	interrupt-controller;
+	pinctrl-single,register-width = <16>;
+	pinctrl-single,function-mask = <0xffff>;
+};
+
+control_devconf0: pinmux@48002274 {
+	compatible = "pinctrl-single";
+	reg = <0x48002274 4>;	/* Single register */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-single,bit-per-mux;
+	pinctrl-single,register-width = <32>;
+	pinctrl-single,function-mask = <0x5F>;
+};
+
+/* third controller instance for pins in gpio domain */
+pmx_gpio: pinmux@d401e000 {
+	compatible = "pinconf-single";
+	reg = <0xd401e000 0x0330>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	pinctrl-single,register-width = <32>;
+	pinctrl-single,function-mask = <7>;
+
+	/* sparse GPIO range could be supported */
+	pinctrl-single,gpio-range = <&range 0 3 0 &range 3 9 1
+				&range 12 1 0 &range 13 29 1
+				&range 43 1 0 &range 44 49 1
+				&range 94 1 1 &range 96 2 1>;
+
+	range: gpio-range {
+		#pinctrl-single,gpio-range-cells = <3>;
+	};
+};
+
+
+/* board specific .dts file */
+
+&pmx_core {
+
+	/*
+	 * map all board specific static pins enabled by the pinctrl driver
+	 * itself during the boot (or just set them up in the bootloader)
+	 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&board_pins>;
+
+	board_pins: pinmux_board_pins {
+		pinctrl-single,pins = <
+			0x6c 0xf
+			0x6e 0xf
+			0x70 0xf
+			0x72 0xf
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			0x208 0		/* UART0_RXD (IOCFG138) */
+			0x20c 0		/* UART0_TXD (IOCFG139) */
+		>;
+		pinctrl-single,bias-pulldown = <0 2 2>;
+		pinctrl-single,bias-pullup = <0 1 1>;
+	};
+
+	/* map uart2 pins */
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			0xd8 0x118
+			0xda 0
+			0xdc 0x118
+			0xde 0
+		>;
+	};
+};
+
+&control_devconf0 {
+	mcbsp1_pins: pinmux_mcbsp1_pins {
+		pinctrl-single,bits = <
+			0x00 0x18 0x18 /* FSR/CLKR signal from FSX/CLKX pin */
+		>;
+	};
+
+	mcbsp2_clks_pins: pinmux_mcbsp2_clks_pins {
+		pinctrl-single,bits = <
+			0x00 0x40 0x40 /* McBSP2 CLKS from McBSP_CLKS pin */
+		>;
+	};
+
+};
+
+&uart1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_pins>;
+};
+
+&uart2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart2_pins>;
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt
new file mode 100644
index 000000000..5f55be59d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt
@@ -0,0 +1,47 @@
+CSR SiRFprimaII pinmux controller
+
+Required properties:
+- compatible	: "sirf,prima2-pinctrl"
+- reg		: Address range of the pinctrl registers
+- interrupts    : Interrupts used by every GPIO group
+- gpio-controller : Indicates this device is a GPIO controller
+- interrupt-controller  : Marks the device node as an interrupt controller
+Optional properties:
+- sirf,pullups : if n-th bit of m-th bank is set, set a pullup on GPIO-n of bank m
+- sirf,pulldowns : if n-th bit of m-th bank is set, set a pulldown on GPIO-n of bank m
+
+Please refer to pinctrl-bindings.txt in this directory for details of the common
+pinctrl bindings used by client devices.
+
+SiRFprimaII's pinmux nodes act as a container for an arbitrary number of subnodes.
+Each of these subnodes represents some desired configuration for a group of pins.
+
+Required subnode-properties:
+- sirf,pins : An array of strings. Each string contains the name of a group.
+- sirf,function: A string containing the name of the function to mux to the
+  group.
+
+  Valid values for group and function names can be found from looking at the
+  group and function arrays in driver files:
+  drivers/pinctrl/pinctrl-sirf.c
+
+For example, pinctrl might have subnodes like the following:
+ uart2_pins_a: uart2@0 {
+         uart {
+                 sirf,pins = "uart2grp";
+                 sirf,function = "uart2";
+         };
+ };
+ uart2_noflow_pins_a: uart2@1 {
+         uart {
+                 sirf,pins = "uart2_nostreamctrlgrp";
+                 sirf,function = "uart2_nostreamctrl";
+         };
+ };
+
+For a specific board, if it wants to use uart2 without hardware flow control,
+it can add the following to its board-specific .dts file.
+uart2: uart@0xb0070000 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_noflow_pins_a>;
+}
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt
new file mode 100644
index 000000000..26bcb18f4
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt
@@ -0,0 +1,171 @@
+*ST pin controller.
+
+Each multi-function pin is controlled, driven and routed through the
+PIO multiplexing block. Each pin supports GPIO functionality (ALT0)
+and multiple alternate functions(ALT1 - ALTx) that directly connect
+the pin to different hardware blocks.
+
+When a pin is in GPIO mode, Output Enable (OE), Open Drain(OD), and
+Pull Up (PU) are driven by the related PIO block.
+
+ST pinctrl driver controls PIO multiplexing block and also interacts with
+gpio driver to configure a pin.
+
+GPIO bank can have one of the two possible types of interrupt-wirings.
+
+First type is via irqmux, single interrupt is used by multiple gpio banks. This
+reduces number of overall interrupts numbers required. All these banks belong to
+a single pincontroller.
+		  _________
+		 |	   |----> [gpio-bank (n)    ]
+		 |	   |----> [gpio-bank (n + 1)]
+	[irqN]-- | irq-mux |----> [gpio-bank (n + 2)]
+		 |	   |----> [gpio-bank (...  )]
+		 |_________|----> [gpio-bank (n + 7)]
+
+Second type has a dedicated interrupt per gpio bank.
+
+	[irqN]----> [gpio-bank (n)]
+
+
+Pin controller node:
+Required properties:
+- compatible	: should be "st,<SOC>-<pio-block>-pinctrl"
+	like st,stih415-sbc-pinctrl, st,stih415-front-pinctrl and so on.
+- st,syscfg		: Should be a phandle of the syscfg node.
+- st,retime-pin-mask	: Should be mask to specify which pins can be retimed.
+	If the property is not present, it is assumed that all the pins in the
+	bank are capable of retiming. Retiming is mainly used to improve the
+	IO timing margins of external synchronous interfaces.
+- ranges : defines mapping between pin controller node (parent) to gpio-bank
+  node (children).
+
+Optional properties:
+- interrupts	: Interrupt number of the irqmux. If the interrupt is shared
+  with other gpio banks via irqmux.
+  a irqline and gpio banks.
+- reg		: irqmux memory resource. If irqmux is present.
+- reg-names	: irqmux resource should be named as "irqmux".
+
+GPIO controller/bank node.
+Required properties:
+- gpio-controller : Indicates this device is a GPIO controller
+- #gpio-cells	  : Should be one. The first cell is the pin number.
+- st,bank-name	  : Should be a name string for this bank as specified in
+  datasheet.
+
+Optional properties:
+- interrupts	: Interrupt number for this gpio bank. If there is a dedicated
+  interrupt wired up for this gpio bank.
+
+- interrupt-controller : Indicates this device is a interrupt controller. GPIO
+  bank can be an interrupt controller iff one of the interrupt type either via
+irqmux or a dedicated interrupt per bank is specified.
+
+- #interrupt-cells: the value of this property should be 2.
+     - First Cell: represents the external gpio interrupt number local to the
+       gpio interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+for related macros look in:
+include/dt-bindings/interrupt-controller/irq.h
+
+Example:
+	pin-controller-sbc {
+		#address-cells	= <1>;
+		#size-cells	= <1>;
+		compatible	= "st,stih415-sbc-pinctrl";
+		st,syscfg	= <&syscfg_sbc>;
+		reg 		= <0xfe61f080 0x4>;
+		reg-names	= "irqmux";
+		interrupts 	= <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names	= "irqmux";
+		ranges 		= <0 0xfe610000 0x5000>;
+
+		PIO0: gpio@fe610000 {
+			gpio-controller;
+			#gpio-cells	= <1>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg		= <0 0x100>;
+			st,bank-name	= "PIO0";
+		};
+		...
+		pin-functions nodes follow...
+	};
+
+
+Contents of function subnode node:
+----------------------
+Required properties for pin configuration node:
+- st,pins	: Child node with list of pins with configuration.
+
+Below is the format of how each pin conf should look like.
+
+<bank offset mux mode rt_type rt_delay rt_clk>
+
+Every PIO is represented with 4-7 parameters depending on retime configuration.
+Each parameter is explained as below.
+
+-bank		: Should be bank phandle to which this PIO belongs.
+-offset		: Offset in the PIO bank.
+-mux		: Should be alternate function number associated this pin.
+		Use same numbers from datasheet.
+-mode		:pin configuration is selected from one of the below values.
+		IN
+		IN_PU
+		OUT
+		BIDIR
+		BIDIR_PU
+
+-rt_type	Retiming Configuration for the pin.
+		Possible retime configuration are:
+
+		-------		-------------
+		value		args
+		-------		-------------
+		NICLK		<delay> <clk>
+		ICLK_IO		<delay> <clk>
+		BYPASS		<delay>
+		DE_IO		<delay> <clk>
+		SE_ICLK_IO	<delay> <clk>
+		SE_NICLK_IO	<delay> <clk>
+
+- delay	is retime delay in pico seconds as mentioned in data sheet.
+
+- rt_clk	:clk to be use for retime.
+		Possible values are:
+		CLK_A
+		CLK_B
+		CLK_C
+		CLK_D
+
+Example of mmcclk pin which is a bi-direction pull pu with retime config
+as non inverted clock retimed with CLK_B and delay of 0 pico seconds:
+
+pin-controller {
+	...
+	mmc0 {
+		pinctrl_mmc: mmc {
+			st,pins {
+				mmcclk = <&PIO13 4 ALT4 BIDIR_PU NICLK 0 CLK_B>;
+				...
+			};
+		};
+	...
+	};
+};
+
+sdhci0:sdhci@fe810000{
+	...
+	interrupt-parent = <&PIO3>;
+	#interrupt-cells = <2>;
+	interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; /* Interrupt line via PIO3-3 */
+	interrupt-names = "card-detect";
+	pinctrl-names = "default";
+	pinctrl-0	= <&pinctrl_mmc>;
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-vt8500.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-vt8500.txt
new file mode 100644
index 000000000..b3aa90f0c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-vt8500.txt
@@ -0,0 +1,57 @@
+VIA VT8500 and Wondermedia WM8xxx-series pinmux/gpio controller
+
+These SoCs contain a combined Pinmux/GPIO module. Each pin may operate as
+either a GPIO in, GPIO out or as an alternate function (I2C, SPI etc).
+
+Required properties:
+- compatible: "via,vt8500-pinctrl", "wm,wm8505-pinctrl", "wm,wm8650-pinctrl",
+	"wm8750-pinctrl" or "wm,wm8850-pinctrl"
+- reg: Should contain the physical address of the module's registers.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be two.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters.
+	bit 0 - active low
+
+Please refer to ../gpio/gpio.txt for a general description of GPIO bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Each pin configuration node lists the pin(s) to which it applies, and one or
+more of the mux functions to select on those pin(s), and pull-up/down
+configuration. Each subnode only affects those parameters that are explicitly
+listed. In other words, a subnode that lists only a mux function implies no
+information about any pull configuration. Similarly, a subnode that lists only
+a pull parameter implies no information about the mux function.
+
+Required subnode-properties:
+- wm,pins: An array of cells. Each cell contains the ID of a pin.
+
+Optional subnode-properties:
+- wm,function: Integer, containing the function to mux to the pin(s):
+  0: GPIO in
+  1: GPIO out
+  2: alternate
+
+- wm,pull: Integer, representing the pull-down/up to apply to the pin(s):
+  0: none
+  1: down
+  2: up
+
+Each of wm,function and wm,pull may contain either a single value which
+will be applied to all pins in wm,pins, or one value for each entry in
+wm,pins.
+
+Example:
+
+	pinctrl: pinctrl {
+		compatible = "wm,wm8505-pinctrl";
+		reg = <0xD8110000 0x10000>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt
new file mode 100644
index 000000000..458615596
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl_spear.txt
@@ -0,0 +1,155 @@
+ST Microelectronics, SPEAr pinmux controller
+
+Required properties:
+- compatible	: "st,spear300-pinmux"
+		: "st,spear310-pinmux"
+		: "st,spear320-pinmux"
+		: "st,spear1310-pinmux"
+		: "st,spear1340-pinmux"
+- reg		: Address range of the pinctrl registers
+- st,pinmux-mode: Mandatory for SPEAr300 and SPEAr320 and invalid for others.
+	- Its values for SPEAr300:
+		- NAND_MODE		: <0>
+		- NOR_MODE		: <1>
+		- PHOTO_FRAME_MODE	: <2>
+		- LEND_IP_PHONE_MODE	: <3>
+		- HEND_IP_PHONE_MODE	: <4>
+		- LEND_WIFI_PHONE_MODE	: <5>
+		- HEND_WIFI_PHONE_MODE	: <6>
+		- ATA_PABX_WI2S_MODE	: <7>
+		- ATA_PABX_I2S_MODE	: <8>
+		- CAML_LCDW_MODE	: <9>
+		- CAMU_LCD_MODE		: <10>
+		- CAMU_WLCD_MODE	: <11>
+		- CAML_LCD_MODE		: <12>
+	- Its values for SPEAr320:
+		- AUTO_NET_SMII_MODE	: <0>
+		- AUTO_NET_MII_MODE	: <1>
+		- AUTO_EXP_MODE		: <2>
+		- SMALL_PRINTERS_MODE	: <3>
+		- EXTENDED_MODE		: <4>
+
+Please refer to pinctrl-bindings.txt in this directory for details of the common
+pinctrl bindings used by client devices.
+
+SPEAr's pinmux nodes act as a container for an arbitrary number of subnodes. Each
+of these subnodes represents muxing for a pin, a group, or a list of pins or
+groups.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Required subnode-properties:
+- st,pins : An array of strings. Each string contains the name of a pin or
+  group.
+- st,function: A string containing the name of the function to mux to the pin or
+  group. See the SPEAr's TRM to determine which are valid for each pin or group.
+
+  Valid values for group and function names can be found from looking at the
+  group and function arrays in driver files:
+  drivers/pinctrl/spear/pinctrl-spear3*0.c
+
+Valid values for group names are:
+For All SPEAr3xx machines:
+	"firda_grp", "i2c0_grp", "ssp_cs_grp", "ssp0_grp", "mii0_grp",
+	"gpio0_pin0_grp", "gpio0_pin1_grp", "gpio0_pin2_grp", "gpio0_pin3_grp",
+	"gpio0_pin4_grp", "gpio0_pin5_grp", "uart0_ext_grp", "uart0_grp",
+	"timer_0_1_grp", timer_0_1_pins, "timer_2_3_grp"
+
+For SPEAr300 machines:
+	"fsmc_2chips_grp", "fsmc_4chips_grp", "clcd_lcdmode_grp",
+	"clcd_pfmode_grp", "tdm_grp", "i2c_clk_grp_grp", "caml_grp", "camu_grp",
+	"dac_grp", "i2s_grp", "sdhci_4bit_grp", "sdhci_8bit_grp",
+	"gpio1_0_to_3_grp", "gpio1_4_to_7_grp"
+
+For SPEAr310 machines:
+	"emi_cs_0_to_5_grp", "uart1_grp", "uart2_grp", "uart3_grp", "uart4_grp",
+	"uart5_grp", "fsmc_grp", "rs485_0_grp", "rs485_1_grp", "tdm_grp"
+
+For SPEAr320 machines:
+	"clcd_grp", "emi_grp", "fsmc_8bit_grp", "fsmc_16bit_grp", "spp_grp",
+	"sdhci_led_grp", "sdhci_cd_12_grp", "sdhci_cd_51_grp", "i2s_grp",
+	"uart1_grp", "uart1_modem_2_to_7_grp", "uart1_modem_31_to_36_grp",
+	"uart1_modem_34_to_45_grp", "uart1_modem_80_to_85_grp", "uart2_grp",
+	"uart3_8_9_grp", "uart3_15_16_grp", "uart3_41_42_grp",
+	"uart3_52_53_grp", "uart3_73_74_grp", "uart3_94_95_grp",
+	"uart3_98_99_grp", "uart4_6_7_grp", "uart4_13_14_grp",
+	"uart4_39_40_grp", "uart4_71_72_grp", "uart4_92_93_grp",
+	"uart4_100_101_grp", "uart5_4_5_grp", "uart5_37_38_grp",
+	"uart5_69_70_grp", "uart5_90_91_grp", "uart6_2_3_grp",
+	"uart6_88_89_grp", "rs485_grp", "touchscreen_grp", "can0_grp",
+	"can1_grp", "pwm0_1_pin_8_9_grp", "pwm0_1_pin_14_15_grp",
+	"pwm0_1_pin_30_31_grp", "pwm0_1_pin_37_38_grp", "pwm0_1_pin_42_43_grp",
+	"pwm0_1_pin_59_60_grp", "pwm0_1_pin_88_89_grp", "pwm2_pin_7_grp",
+	"pwm2_pin_13_grp", "pwm2_pin_29_grp", "pwm2_pin_34_grp",
+	"pwm2_pin_41_grp", "pwm2_pin_58_grp", "pwm2_pin_87_grp",
+	"pwm3_pin_6_grp", "pwm3_pin_12_grp", "pwm3_pin_28_grp",
+	"pwm3_pin_40_grp", "pwm3_pin_57_grp", "pwm3_pin_86_grp",
+	"ssp1_17_20_grp", "ssp1_36_39_grp", "ssp1_48_51_grp", "ssp1_65_68_grp",
+	"ssp1_94_97_grp", "ssp2_13_16_grp", "ssp2_32_35_grp", "ssp2_44_47_grp",
+	"ssp2_61_64_grp", "ssp2_90_93_grp", "mii2_grp", "smii0_1_grp",
+	"rmii0_1_grp", "i2c1_8_9_grp", "i2c1_98_99_grp", "i2c2_0_1_grp",
+	"i2c2_2_3_grp", "i2c2_19_20_grp", "i2c2_75_76_grp", "i2c2_96_97_grp"
+
+For SPEAr1310 machines:
+	"i2c0_grp", "ssp0_grp", "ssp0_cs0_grp", "ssp0_cs1_2_grp", "i2s0_grp",
+	"i2s1_grp", "clcd_grp", "clcd_high_res_grp", "arm_gpio_grp",
+	"smi_2_chips_grp", "smi_4_chips_grp", "gmii_grp", "rgmii_grp",
+	"smii_0_1_2_grp", "ras_mii_txclk_grp", "nand_8bit_grp",
+	"nand_16bit_grp", "nand_4_chips_grp", "keyboard_6x6_grp",
+	"keyboard_rowcol6_8_grp", "uart0_grp", "uart0_modem_grp",
+	"gpt0_tmr0_grp", "gpt0_tmr1_grp", "gpt1_tmr0_grp", "gpt1_tmr1_grp",
+	"sdhci_grp", "cf_grp", "xd_grp", "touch_xy_grp",
+	"uart1_disable_i2c_grp", "uart1_disable_sd_grp", "uart2_3_grp",
+	"uart4_grp", "uart5_grp", "rs485_0_1_tdm_0_1_grp", "i2c_1_2_grp",
+	"i2c3_dis_smi_clcd_grp", "i2c3_dis_sd_i2s0_grp", "i2c_4_5_dis_smi_grp",
+	"i2c4_dis_sd_grp", "i2c5_dis_sd_grp", "i2c_6_7_dis_kbd_grp",
+	"i2c6_dis_sd_grp", "i2c7_dis_sd_grp", "can0_dis_nor_grp",
+	"can0_dis_sd_grp", "can1_dis_sd_grp", "can1_dis_kbd_grp", "pcie0_grp",
+	"pcie1_grp", "pcie2_grp", "sata0_grp", "sata1_grp", "sata2_grp",
+	"ssp1_dis_kbd_grp", "ssp1_dis_sd_grp", "gpt64_grp"
+
+For SPEAr1340 machines:
+	"pads_as_gpio_grp", "fsmc_8bit_grp", "fsmc_16bit_grp", "fsmc_pnor_grp",
+	"keyboard_row_col_grp", "keyboard_col5_grp", "spdif_in_grp",
+	"spdif_out_grp", "gpt_0_1_grp", "pwm0_grp", "pwm1_grp", "pwm2_grp",
+	"pwm3_grp", "vip_mux_grp", "vip_mux_cam0_grp", "vip_mux_cam1_grp",
+	"vip_mux_cam2_grp", "vip_mux_cam3_grp", "cam0_grp", "cam1_grp",
+	"cam2_grp", "cam3_grp", "smi_grp", "ssp0_grp", "ssp0_cs1_grp",
+	"ssp0_cs2_grp", "ssp0_cs3_grp", "uart0_grp", "uart0_enh_grp",
+	"uart1_grp", "i2s_in_grp", "i2s_out_grp", "gmii_grp", "rgmii_grp",
+	"rmii_grp", "sgmii_grp", "i2c0_grp", "i2c1_grp", "cec0_grp", "cec1_grp",
+	"sdhci_grp", "cf_grp", "xd_grp", "clcd_grp", "arm_trace_grp",
+	"miphy_dbg_grp", "pcie_grp", "sata_grp"
+
+Valid values for function names are:
+For All SPEAr3xx machines:
+	"firda", "i2c0", "ssp_cs", "ssp0", "mii0", "gpio0", "uart0_ext",
+	"uart0", "timer_0_1", "timer_2_3"
+
+For SPEAr300 machines:
+	"fsmc", "clcd", "tdm", "i2c1", "cam", "dac", "i2s", "sdhci", "gpio1"
+
+For SPEAr310 machines:
+	"emi", "uart1", "uart2", "uart3", "uart4", "uart5", "fsmc", "rs485_0",
+	"rs485_1", "tdm"
+
+For SPEAr320 machines:
+	"clcd", "emi", "fsmc", "spp", "sdhci", "i2s", "uart1", "uart1_modem",
+	"uart2", "uart3", "uart4", "uart5", "uart6", "rs485", "touchscreen",
+	"can0", "can1", "pwm0_1", "pwm2", "pwm3", "ssp1", "ssp2", "mii2",
+	"mii0_1", "i2c1", "i2c2"
+
+
+For SPEAr1310 machines:
+	"i2c0", "ssp0", "i2s0", "i2s1", "clcd", "arm_gpio", "smi", "gmii",
+	"rgmii", "smii_0_1_2", "ras_mii_txclk", "nand", "keyboard", "uart0",
+	"gpt0", "gpt1", "sdhci", "cf", "xd", "touchscreen", "uart1", "uart2_3",
+	"uart4", "uart5", "rs485_0_1_tdm_0_1", "i2c_1_2", "i2c3_i2s1",
+	"i2c_4_5", "i2c_6_7", "can0", "can1", "pci", "sata", "ssp1", "gpt64"
+
+For SPEAr1340 machines:
+	"pads_as_gpio", "fsmc", "keyboard", "spdif_in", "spdif_out", "gpt_0_1",
+	"pwm", "vip", "cam0", "cam1", "cam2", "cam3", "smi", "ssp0", "uart0",
+	"uart1", "i2s", "gmac", "i2c0", "i2c1", "cec0", "cec1", "sdhci", "cf",
+	"xd", "clcd", "arm_trace", "miphy_dbg", "pcie", "sata"
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
new file mode 100644
index 000000000..a7bde6479
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt
@@ -0,0 +1,88 @@
+Qualcomm APQ8064 TLMM block
+
+Required properties:
+- compatible: "qcom,apq8064-pinctrl"
+- reg: Should be the base address and length of the TLMM block.
+- interrupts: Should be the parent IRQ of the TLMM block.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be two.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two.
+                The first cell is the gpio pin number and the
+                second cell is used for optional parameters.
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Qualcomm's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+ pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength,
+ output-low, output-high.
+
+Non-empty subnodes must specify the 'pins' property.
+
+Valid values for pins are:
+  gpio0-gpio89
+
+Valid values for function are:
+  cam_mclk, codec_mic_i2s, codec_spkr_i2s, gpio, gsbi1, gsbi2, gsbi3, gsbi4,
+  gsbi4_cam_i2c, gsbi5, gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6,
+  gsbi6_spi_cs1, gsbi6_spi_cs2, gsbi6_spi_cs3, gsbi7, gsbi7_spi_cs1,
+  gsbi7_spi_cs2, gsbi7_spi_cs3, gsbi_cam_i2c, hdmi, mi2s, riva_bt, riva_fm,
+  riva_wlan, sdc2, sdc4, slimbus, spkr_i2s, tsif1, tsif2, usb2_hsic, ps_hold
+
+Example:
+
+	msmgpio: pinctrl@800000 {
+		compatible = "qcom,apq8064-pinctrl";
+		reg = <0x800000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 16 0x4>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gsbi5_uart_default>;
+
+		gsbi5_uart_default: gsbi5_uart_default {
+			mux {
+				pins = "gpio51", "gpio52";
+				function = "gsbi5";
+			};
+
+			tx {
+				pins = "gpio51";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio52";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt
new file mode 100644
index 000000000..c4ea61ac5
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8084-pinctrl.txt
@@ -0,0 +1,179 @@
+Qualcomm APQ8084 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MSM8960 platform.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be "qcom,apq8084-pinctrl"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.  Valid pins are:
+		    gpio0-gpio146,
+		    sdc1_clk,
+		    sdc1_cmd,
+		    sdc1_data
+		    sdc2_clk,
+		    sdc2_cmd,
+		    sdc2_data
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins. Functions are only valid for gpio pins.
+		    Valid values are:
+		    adsp_ext, audio_ref, blsp_i2c1, blsp_i2c2, blsp_i2c3,
+		    blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8,
+		    blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12,
+		    blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5,
+		    blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10,
+		    blsp_spi11, blsp_spi12, blsp_uart1, blsp_uart2, blsp_uart3,
+		    blsp_uart4, blsp_uart5, blsp_uart6, blsp_uart7, blsp_uart8,
+		    blsp_uart9, blsp_uart10, blsp_uart11, blsp_uart12,
+		    blsp_uim1, blsp_uim2, blsp_uim3, blsp_uim4, blsp_uim5,
+		    blsp_uim6, blsp_uim7, blsp_uim8, blsp_uim9, blsp_uim10,
+		    blsp_uim11, blsp_uim12, cam_mclk0, cam_mclk1, cam_mclk2,
+		    cam_mclk3, cci_async, cci_async_in0, cci_i2c0, cci_i2c1,
+		    cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4,
+		    edp_hpd, gcc_gp1, gcc_gp2, gcc_gp3, gcc_obt, gcc_vtt,i
+		    gp_mn, gp_pdm0, gp_pdm1, gp_pdm2, gp0_clk, gp1_clk, gpio,
+		    hdmi_cec, hdmi_ddc, hdmi_dtest, hdmi_hpd, hdmi_rcv, hsic,
+		    ldo_en, ldo_update, mdp_vsync, pci_e0, pci_e0_n, pci_e0_rst,
+		    pci_e1, pci_e1_rst, pci_e1_rst_n, pci_e1_clkreq_n, pri_mi2s,
+		    qua_mi2s, sata_act, sata_devsleep, sata_devsleep_n,
+		    sd_write, sdc_emmc_mode, sdc3, sdc4, sec_mi2s, slimbus,
+		    spdif_tx, spkr_i2s, spkr_i2s_ws, spss_geni, ter_mi2s, tsif1,
+		    tsif2, uim, uim_batt_alarm
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull up.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+		    Not valid for sdc pins.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+		    Not valid for sdc pins.
+
+- drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins, in mA.
+		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+	tlmm: pinctrl@fd510000 {
+		compatible = "qcom,apq8084-pinctrl";
+		reg = <0xfd510000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 208 0>;
+
+		uart2: uart2-default {
+			mux {
+				pins = "gpio4", "gpio5";
+				function = "blsp_uart2";
+			};
+
+			tx {
+				pins = "gpio4";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio5";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
new file mode 100644
index 000000000..6e88e91fe
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt
@@ -0,0 +1,95 @@
+Qualcomm IPQ8064 TLMM block
+
+Required properties:
+- compatible: "qcom,ipq8064-pinctrl"
+- reg: Should be the base address and length of the TLMM block.
+- interrupts: Should be the parent IRQ of the TLMM block.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be two.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two.
+                The first cell is the gpio pin number and the
+                second cell is used for optional parameters.
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Qualcomm's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+ pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength,
+ output-low, output-high.
+
+Non-empty subnodes must specify the 'pins' property.
+
+Valid values for qcom,pins are:
+  gpio0-gpio68
+   Supports mux, bias, and drive-strength
+
+  sdc3_clk, sdc3_cmd, sdc3_data
+   Supports bias and drive-strength
+
+
+Valid values for function are:
+  mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gpio, gsbi1, gsbi2, gsbi4, gsbi5,
+  gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1,
+  spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata,
+  pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt,
+  pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren,
+  pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n,
+  pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold
+
+Example:
+
+	pinmux: pinctrl@800000 {
+		compatible = "qcom,ipq8064-pinctrl";
+		reg = <0x800000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 32 0x4>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gsbi5_uart_default>;
+
+		gsbi5_uart_default: gsbi5_uart_default {
+			mux {
+				pins = "gpio18", "gpio19";
+				function = "gsbi5";
+			};
+
+			tx {
+				pins = "gpio18";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio19";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt
new file mode 100644
index 000000000..498caff60
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt
@@ -0,0 +1,186 @@
+Qualcomm MSM8916 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MSM8916 platform.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be "qcom,msm8916-pinctrl"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.  Valid pins are:
+		    gpio0-gpio121,
+		    sdc1_clk,
+		    sdc1_cmd,
+		    sdc1_data
+		    sdc2_clk,
+		    sdc2_cmd,
+		    sdc2_data,
+		    qdsd_cmd,
+		    qdsd_data0,
+		    qdsd_data1,
+		    qdsd_data2,
+		    qdsd_data3
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins. Functions are only valid for gpio pins.
+		    Valid values are:
+	adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1, atest_char, atest_char0,
+	atest_char1, atest_char2, atest_char3, atest_combodac, atest_gpsadc0,
+	atest_gpsadc1, atest_tsens, atest_wlan0, atest_wlan1, backlight_en,
+	bimc_dte0,bimc_dte1, blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4,
+	blsp_i2c5, blsp_i2c6, blsp_spi1, blsp_spi1_cs1, blsp_spi1_cs2,
+	blsp_spi1_cs3, blsp_spi2, blsp_spi2_cs1, blsp_spi2_cs2, blsp_spi2_cs3,
+	blsp_spi3, blsp_spi3_cs1, blsp_spi3_cs2, blsp_spi3_cs3, blsp_spi4,
+	blsp_spi5, blsp_spi6, blsp_uart1, blsp_uart2, blsp_uim1, blsp_uim2,
+	cam1_rst, cam1_standby, cam_mclk0, cam_mclk1, cci_async, cci_i2c,
+	cci_timer0, cci_timer1, cci_timer2, cdc_pdm0, codec_mad, dbg_out,
+	display_5v, dmic0_clk, dmic0_data, dsi_rst, ebi0_wrcdc, euro_us,
+	ext_lpass, flash_strobe, gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a,
+	gcc_gp2_clk_b, gcc_gp3_clk_a, gcc_gp3_clk_b, gpio, gsm0_tx0, gsm0_tx1,
+	gsm1_tx0, gsm1_tx1, gyro_accl, kpsns0, kpsns1, kpsns2, ldo_en,
+	ldo_update, mag_int, mdp_vsync, modem_tsync, m_voc, nav_pps, nav_tsync,
+	pa_indicator, pbs0, pbs1, pbs2, pri_mi2s, pri_mi2s_ws, prng_rosc,
+	pwr_crypto_enabled_a, pwr_crypto_enabled_b, pwr_modem_enabled_a,
+	pwr_modem_enabled_b, pwr_nav_enabled_a, pwr_nav_enabled_b,
+	qdss_ctitrig_in_a0, qdss_ctitrig_in_a1, qdss_ctitrig_in_b0,
+	qdss_ctitrig_in_b1, qdss_ctitrig_out_a0, qdss_ctitrig_out_a1,
+	qdss_ctitrig_out_b0, qdss_ctitrig_out_b1, qdss_traceclk_a,
+	qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a,
+	qdss_tracedata_b, reset_n, sd_card, sd_write, sec_mi2s, smb_int,
+	ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3, uim_batt, wcss_bt, wcss_fm,
+	wcss_wlan, webcam1_rst
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull up.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+		    Not valid for sdc pins.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+		    Not valid for sdc pins.
+
+- drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins, in mA.
+		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+	tlmm: pinctrl@1000000 {
+		compatible = "qcom,msm8916-pinctrl";
+		reg = <0x1000000 0x300000>;
+		interrupts = <0 208 0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		uart2: uart2-default {
+			mux {
+				pins = "gpio4", "gpio5";
+				function = "blsp_uart2";
+			};
+
+			tx {
+				pins = "gpio4";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio5";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt
new file mode 100644
index 000000000..eb8d8aa41
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.txt
@@ -0,0 +1,181 @@
+Qualcomm MSM8960 TLMM block
+
+This binding describes the Top Level Mode Multiplexer block found in the
+MSM8960 platform.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be "qcom,msm8960-pinctrl"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: the base address and size of the TLMM register space.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: should specify the TLMM summary IRQ.
+
+- interrupt-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as an interrupt controller
+
+- #interrupt-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/interrupt-controller/irq.h>
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: identifies this node as a gpio controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: must be 2. Specifying the pin number and flags, as defined
+		    in <dt-bindings/gpio/gpio.h>
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+
+PIN CONFIGURATION NODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.  Valid pins are:
+		    gpio0-gpio151,
+		    sdc1_clk,
+		    sdc1_cmd,
+		    sdc1_data
+		    sdc3_clk,
+		    sdc3_cmd,
+		    sdc3_data
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins. Functions are only valid for gpio pins.
+		    Valid values are:
+		    audio_pcm, bt, cam_mclk0, cam_mclk1, cam_mclk2,
+		    codec_mic_i2s, codec_spkr_i2s, ext_gps, fm, gps_blanking,
+		    gps_pps_in, gps_pps_out, gp_clk_0a, gp_clk_0b, gp_clk_1a,
+		    gp_clk_1b, gp_clk_2a, gp_clk_2b, gp_mn, gp_pdm_0a,
+		    gp_pdm_0b, gp_pdm_1a, gp_pdm_1b, gp_pdm_2a, gp_pdm_2b, gpio,
+		    gsbi1, gsbi1_spi_cs1_n, gsbi1_spi_cs2a_n, gsbi1_spi_cs2b_n,
+		    gsbi1_spi_cs3_n, gsbi2, gsbi2_spi_cs1_n, gsbi2_spi_cs2_n,
+		    gsbi2_spi_cs3_n, gsbi3, gsbi4, gsbi4_3d_cam_i2c_l,
+		    gsbi4_3d_cam_i2c_r, gsbi5, gsbi5_3d_cam_i2c_l,
+		    gsbi5_3d_cam_i2c_r, gsbi6, gsbi7, gsbi8, gsbi9, gsbi10,
+		    gsbi11, gsbi11_spi_cs1a_n, gsbi11_spi_cs1b_n,
+		    gsbi11_spi_cs2a_n, gsbi11_spi_cs2b_n, gsbi11_spi_cs3_n,
+		    gsbi12, hdmi_cec, hdmi_ddc_clock, hdmi_ddc_data,
+		    hdmi_hot_plug_detect, hsic, mdp_vsync, mi2s, mic_i2s,
+		    pmb_clk, pmb_ext_ctrl, ps_hold, rpm_wdog, sdc2, sdc4, sdc5,
+		    slimbus1, slimbus2, spkr_i2s, ssbi1, ssbi2, ssbi_ext_gps,
+		    ssbi_pmic2, ssbi_qpa1, ssbi_ts, tsif1, tsif2, ts_eoc,
+		    usb_fs1, usb_fs1_oe, usb_fs1_oe_n, usb_fs2, usb_fs2_oe,
+		    usb_fs2_oe_n, vfe_camif_timer1_a, vfe_camif_timer1_b,
+		    vfe_camif_timer2, vfe_camif_timer3_a, vfe_camif_timer3_b,
+		    vfe_camif_timer4_a, vfe_camif_timer4_b, vfe_camif_timer4_c,
+		    vfe_camif_timer5_a, vfe_camif_timer5_b, vfe_camif_timer6_a,
+		    vfe_camif_timer6_b, vfe_camif_timer6_c, vfe_camif_timer7_a,
+		    vfe_camif_timer7_b, vfe_camif_timer7_c, wlan
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configued as pull up.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+		    Not valid for sdc pins.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+		    Not valid for sdc pins.
+
+- drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins, in mA.
+		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
+
+Example:
+
+	msmgpio: pinctrl@800000 {
+		compatible = "qcom,msm8960-pinctrl";
+		reg = <0x800000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 16 0x4>;
+
+		gsbi8_uart: gsbi8-uart {
+			mux {
+				pins = "gpio34", "gpio35";
+				function = "gsbi8";
+			};
+
+			tx {
+				pins = "gpio34";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio35";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
new file mode 100644
index 000000000..e4d6a9d20
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt
@@ -0,0 +1,112 @@
+Qualcomm MSM8974 TLMM block
+
+Required properties:
+- compatible: "qcom,msm8974-pinctrl"
+- reg: Should be the base address and length of the TLMM block.
+- interrupts: Should be the parent IRQ of the TLMM block.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Should be two.
+- gpio-controller: Marks the device node as a GPIO controller.
+- #gpio-cells : Should be two.
+                The first cell is the gpio pin number and the
+                second cell is used for optional parameters.
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Qualcomm's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+ pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength.
+
+Non-empty subnodes must specify the 'pins' property.
+Note that not all properties are valid for all pins.
+
+
+Valid values for pins are:
+  gpio0-gpio145
+    Supports mux, bias and drive-strength
+
+  sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data
+    Supports bias and drive-strength
+
+Valid values for function are:
+  cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm,
+  blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1,
+  blsp_uim2, blsp_uart2, blsp_i2c2, blsp_spi2,
+  blsp_uim3, blsp_uart3, blsp_i2c3, blsp_spi3,
+  blsp_uim4, blsp_uart4, blsp_i2c4, blsp_spi4,
+  blsp_uim5, blsp_uart5, blsp_i2c5, blsp_spi5,
+  blsp_uim6, blsp_uart6, blsp_i2c6, blsp_spi6,
+  blsp_uim7, blsp_uart7, blsp_i2c7, blsp_spi7,
+  blsp_uim8, blsp_uart8, blsp_i2c8, blsp_spi8,
+  blsp_uim9, blsp_uart9, blsp_i2c9, blsp_spi9,
+  blsp_uim10, blsp_uart10, blsp_i2c10, blsp_spi10,
+  blsp_uim11, blsp_uart11, blsp_i2c11, blsp_spi11,
+  blsp_uim12, blsp_uart12, blsp_i2c12, blsp_spi12,
+  blsp_spi1_cs1, blsp_spi2_cs2, blsp_spi_cs3, blsp_spi2_cs1, blsp_spi2_cs2
+  blsp_spi2_cs3, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3,
+  sdc3, sdc4, gcc_gp_clk1, gcc_gp_clk2, gcc_gp_clk3, cci_timer0, cci_timer1,
+  cci_timer2, cci_timer3, cci_async_in0, cci_async_in1, cci_async_in2,
+  cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc,
+  hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk,
+  gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s,
+  ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, gpio
+
+  (Note that this is not yet the complete list of functions)
+
+
+
+Example:
+
+	msmgpio: pinctrl@fd510000 {
+		compatible = "qcom,msm8974-pinctrl";
+		reg = <0xfd510000 0x4000>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <0 208 0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart2_default>;
+
+		uart2_default: uart2_default {
+			mux {
+				pins = "gpio4", "gpio5";
+				function = "blsp_uart2";
+			};
+
+			tx {
+				pins = "gpio4";
+				drive-strength = <4>;
+				bias-disable;
+			};
+
+			rx {
+				pins = "gpio5";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
new file mode 100644
index 000000000..1ae63c0ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
@@ -0,0 +1,217 @@
+Qualcomm PMIC GPIO block
+
+This binding describes the GPIO block(s) found in the 8xxx series of
+PMIC's from Qualcomm.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,pm8018-gpio"
+		    "qcom,pm8038-gpio"
+		    "qcom,pm8058-gpio"
+		    "qcom,pm8916-gpio"
+		    "qcom,pm8917-gpio"
+		    "qcom,pm8921-gpio"
+		    "qcom,pm8941-gpio"
+		    "qcom,pma8084-gpio"
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Register base of the GPIO block and length.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Must contain an array of encoded interrupt specifiers for
+		    each available GPIO
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: Mark the device node as a GPIO controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: Must be 2;
+		    the first cell will be used to define gpio number and the
+		    second denotes the flags for this gpio
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin or a list of pins. This configuration can include the
+mux function to select on those pin(s), and various pin configuration
+parameters, as listed below.
+
+
+SUBNODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of gpio pins affected by the properties specified in
+		    this subnode.  Valid pins are:
+		    gpio1-gpio6 for pm8018
+		    gpio1-gpio12 for pm8038
+		    gpio1-gpio40 for pm8058
+		    gpio1-gpio4 for pm8916
+		    gpio1-gpio38 for pm8917
+		    gpio1-gpio44 for pm8921
+		    gpio1-gpio36 for pm8941
+		    gpio1-gpio22 for pma8084
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins.  Valid values are:
+		    "normal",
+		    "paired",
+		    "func1",
+		    "func2",
+		    "dtest1",
+		    "dtest2",
+		    "dtest3",
+		    "dtest4"
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configured as no pull.
+
+- bias-pull-down:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configured as pull down.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <empty>
+	Definition: The specified pins should be configured as pull up.
+
+- qcom,pull-up-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Specifies the strength to use for pull up, if selected.
+		    Valid values are; as defined in
+		    <dt-bindings/pinctrl/qcom,pmic-gpio.h>:
+		    1: 30uA                     (PMIC_GPIO_PULL_UP_30)
+		    2: 1.5uA                    (PMIC_GPIO_PULL_UP_1P5)
+		    3: 31.5uA                   (PMIC_GPIO_PULL_UP_31P5)
+		    4: 1.5uA + 30uA boost       (PMIC_GPIO_PULL_UP_1P5_30)
+		    If this property is ommited 30uA strength will be used if
+		    pull up is selected
+
+- bias-high-impedance:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins will put in high-Z mode and disabled.
+
+- input-enable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are put in input mode.
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+
+- power-source:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the power source for the specified pins. Valid
+		    power sources are defined per chip in
+		    <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+- qcom,drive-strength:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the drive strength for the specified pins. Value
+		    drive strengths are:
+		    0: no (PMIC_GPIO_STRENGTH_NO)
+		    1: high (PMIC_GPIO_STRENGTH_HIGH) 0.9mA @ 1.8V - 1.9mA @ 2.6V
+		    2: medium (PMIC_GPIO_STRENGTH_MED) 0.6mA @ 1.8V - 1.25mA @ 2.6V
+		    3: low (PMIC_GPIO_STRENGTH_LOW) 0.15mA @ 1.8V - 0.3mA @ 2.6V
+		    as defined in <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+- drive-push-pull:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in push-pull mode.
+
+- drive-open-drain:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in open-drain mode.
+
+- drive-open-source:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in open-source mode.
+
+Example:
+
+	pm8921_gpio: gpio@150 {
+		compatible = "qcom,pm8921-gpio";
+		reg = <0x150 0x160>;
+		interrupts = <192 1>, <193 1>, <194 1>,
+			     <195 1>, <196 1>, <197 1>,
+			     <198 1>, <199 1>, <200 1>,
+			     <201 1>, <202 1>, <203 1>,
+			     <204 1>, <205 1>, <206 1>,
+			     <207 1>, <208 1>, <209 1>,
+			     <210 1>, <211 1>, <212 1>,
+			     <213 1>, <214 1>, <215 1>,
+			     <216 1>, <217 1>, <218 1>,
+			     <219 1>, <220 1>, <221 1>,
+			     <222 1>, <223 1>, <224 1>,
+			     <225 1>, <226 1>, <227 1>,
+			     <228 1>, <229 1>, <230 1>,
+			     <231 1>, <232 1>, <233 1>,
+			     <234 1>, <235 1>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		pm8921_gpio_keys: gpio-keys {
+			volume-keys {
+				pins = "gpio20", "gpio21";
+				function = "normal";
+
+				input-enable;
+				bias-pull-up;
+				drive-push-pull;
+				qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+				power-source = <PM8921_GPIO_S4>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
new file mode 100644
index 000000000..ed19991aa
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
@@ -0,0 +1,164 @@
+Qualcomm PMIC Multi-Purpose Pin (MPP) block
+
+This binding describes the MPP block(s) found in the 8xxx series
+of PMIC's from Qualcomm.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: Should contain one of:
+		    "qcom,pm8841-mpp",
+		    "qcom,pm8916-mpp",
+		    "qcom,pm8941-mpp",
+		    "qcom,pma8084-mpp",
+
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Register base of the MPP block and length.
+
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Must contain an array of encoded interrupt specifiers for
+		    each available MPP
+
+- gpio-controller:
+	Usage: required
+	Value type: <none>
+	Definition: Mark the device node as a GPIO controller
+
+- #gpio-cells:
+	Usage: required
+	Value type: <u32>
+	Definition: Must be 2;
+		    the first cell will be used to define MPP number and the
+		    second denotes the flags for this MPP
+
+Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
+a general description of GPIO and interrupt bindings.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin or a list of pins. This configuration can include the
+mux function to select on those pin(s), and various pin configuration
+parameters, as listed below.
+
+SUBNODES:
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pin configuration subnode:
+
+- pins:
+	Usage: required
+	Value type: <string-array>
+	Definition: List of MPP pins affected by the properties specified in
+		    this subnode.  Valid pins are:
+		    mpp1-mpp4 for pm8841
+		    mpp1-mpp4 for pm8916
+		    mpp1-mpp8 for pm8941
+		    mpp1-mpp4 for pma8084
+
+- function:
+	Usage: required
+	Value type: <string>
+	Definition: Specify the alternative function to be configured for the
+		    specified pins.  Valid values are:
+		    "normal",
+		    "paired",
+		    "dtest1",
+		    "dtest2",
+		    "dtest3",
+		    "dtest4"
+
+- bias-disable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins should be configured as no pull.
+
+- bias-pull-up:
+	Usage: optional
+	Value type: <u32>
+	Definition: The specified pins should be configured as pull up.
+		    Valid values are 600, 10000 and 30000 in bidirectional mode
+		    only, i.e. when operating in qcom,analog-mode and input and
+		    outputs are enabled. The hardware ignores the configuration
+		    when operating in other modes.
+
+- bias-high-impedance:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins will put in high-Z mode and disabled.
+
+- input-enable:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are put in input mode, i.e. their input
+		    buffer is enabled
+
+- output-high:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    high.
+
+- output-low:
+	Usage: optional
+	Value type: <none>
+	Definition: The specified pins are configured in output mode, driven
+		    low.
+
+- power-source:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the power source for the specified pins. Valid power
+		    sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+- qcom,analog-mode:
+	Usage: optional
+	Value type: <none>
+	Definition: Selects Analog mode of operation: combined with input-enable
+		    and/or output-high, output-low MPP could operate as
+		    Bidirectional Logic, Analog Input, Analog Output.
+
+- qcom,amux-route:
+	Usage: optional
+	Value type: <u32>
+	Definition: Selects the source for analog input. Valid values are
+		    defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+		    PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6...
+
+Example:
+
+	mpps@a000 {
+		compatible = "qcom,pm8841-mpp";
+		reg = <0xa000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupts = <4 0xa0 0 0>, <4 0xa1 0 0>, <4 0xa2 0 0>, <4 0xa3 0 0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pm8841_default>;
+
+		pm8841_default: default {
+			gpio {
+				pins = "mpp1", "mpp2", "mpp3", "mpp4";
+				function = "normal";
+				input-enable;
+				power-source = <PM8841_MPP_S3>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
new file mode 100644
index 000000000..bfe72ec05
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
@@ -0,0 +1,167 @@
+* Renesas Pin Function Controller (GPIO and Pin Mux/Config)
+
+The Pin Function Controller (PFC) is a Pin Mux/Config controller. On SH73A0,
+R8A73A4 and R8A7740 it also acts as a GPIO controller.
+
+
+Pin Control
+-----------
+
+Required Properties:
+
+  - compatible: should be one of the following.
+    - "renesas,pfc-emev2": for EMEV2 (EMMA Mobile EV2) compatible pin-controller.
+    - "renesas,pfc-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible pin-controller.
+    - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller.
+    - "renesas,pfc-r8a7778": for R8A7778 (R-Mobile M1) compatible pin-controller.
+    - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller.
+    - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller.
+    - "renesas,pfc-r8a7791": for R8A7791 (R-Car M2) compatible pin-controller.
+    - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller.
+
+  - reg: Base address and length of each memory resource used by the pin
+    controller hardware module.
+
+Optional properties:
+
+  - #gpio-range-cells: Mandatory when the PFC doesn't handle GPIO, forbidden
+    otherwise. Should be 3.
+
+  - interrupts-extended: Specify the interrupts associated with external
+    IRQ pins. This property is mandatory when the PFC handles GPIOs and
+    forbidden otherwise. When specified, it must contain one interrupt per
+    external IRQ, sorted by external IRQ number.
+
+The PFC node also acts as a container for pin configuration nodes. Please refer
+to pinctrl-bindings.txt in this directory for the definition of the term "pin
+configuration node" and for the common pinctrl bindings used by client devices.
+
+Each pin configuration node represents a desired configuration for a pin, a
+pin group, or a list of pins or pin groups. The configuration can include the
+function to select on those pin(s) and pin configuration parameters (such as
+pull-up and pull-down).
+
+Pin configuration nodes contain pin configuration properties, either directly
+or grouped in child subnodes. Both pin muxing and configuration parameters can
+be grouped in that way and referenced as a single pin configuration node by
+client devices.
+
+A configuration node or subnode must reference at least one pin (through the
+pins or pin groups properties) and contain at least a function or one
+configuration parameter. When the function is present only pin groups can be
+used to reference pins.
+
+All pin configuration nodes and subnodes names are ignored. All of those nodes
+are parsed through phandles and processed purely based on their content.
+
+Pin Configuration Node Properties:
+
+- renesas,pins : An array of strings, each string containing the name of a pin.
+- renesas,groups : An array of strings, each string containing the name of a pin
+  group.
+
+- renesas,function: A string containing the name of the function to mux to the
+  pin group(s) specified by the renesas,groups property
+
+  Valid values for pin, group and function names can be found in the group and
+  function arrays of the PFC data file corresponding to the SoC
+  (drivers/pinctrl/sh-pfc/pfc-*.c)
+
+The pin configuration parameters use the generic pinconf bindings defined in
+pinctrl-bindings.txt in this directory. The supported parameters are
+bias-disable, bias-pull-up and bias-pull-down.
+
+
+GPIO
+----
+
+On SH73A0, R8A73A4 and R8A7740 the PFC node is also a GPIO controller node.
+
+Required Properties:
+
+  - gpio-controller: Marks the device node as a gpio controller.
+
+  - #gpio-cells: Should be 2. The first cell is the GPIO number and the second
+    cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the
+    GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
+
+The syntax of the gpio specifier used by client nodes should be the following
+with values derived from the SoC user manual.
+
+  <[phandle of the gpio controller node]
+   [pin number within the gpio controller]
+   [flags]>
+
+On other mach-shmobile platforms GPIO is handled by the gpio-rcar driver.
+Please refer to Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt
+for documentation of the GPIO device tree bindings on those platforms.
+
+
+Examples
+--------
+
+Example 1: SH73A0 (SH-Mobile AG5) pin controller node
+
+	pfc: pfc@e6050000 {
+		compatible = "renesas,pfc-sh73a0";
+		reg = <0xe6050000 0x8000>,
+		      <0xe605801c 0x1c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupts-extended =
+			<&irqpin0 0 0>, <&irqpin0 1 0>, <&irqpin0 2 0>, <&irqpin0 3 0>,
+			<&irqpin0 4 0>, <&irqpin0 5 0>, <&irqpin0 6 0>, <&irqpin0 7 0>,
+			<&irqpin1 0 0>, <&irqpin1 1 0>, <&irqpin1 2 0>, <&irqpin1 3 0>,
+			<&irqpin1 4 0>, <&irqpin1 5 0>, <&irqpin1 6 0>, <&irqpin1 7 0>,
+			<&irqpin2 0 0>, <&irqpin2 1 0>, <&irqpin2 2 0>, <&irqpin2 3 0>,
+			<&irqpin2 4 0>, <&irqpin2 5 0>, <&irqpin2 6 0>, <&irqpin2 7 0>,
+			<&irqpin3 0 0>, <&irqpin3 1 0>, <&irqpin3 2 0>, <&irqpin3 3 0>,
+			<&irqpin3 4 0>, <&irqpin3 5 0>, <&irqpin3 6 0>, <&irqpin3 7 0>;
+	};
+
+Example 2: A GPIO LED node that references a GPIO
+
+	#include <dt-bindings/gpio/gpio.h>
+
+	leds {
+		compatible = "gpio-leds";
+		led1 {
+			gpios = <&pfc 20 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+Example 3: KZM-A9-GT (SH-Mobile AG5) default pin state hog and pin control maps
+           for the MMCIF and SCIFA4 devices
+
+	&pfc {
+		pinctrl-0 = <&scifa4_pins>;
+		pinctrl-names = "default";
+
+		mmcif_pins: mmcif {
+			mux {
+				renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0";
+				renesas,function = "mmc0";
+			};
+			cfg {
+				renesas,groups = "mmc0_data8_0";
+				renesas,pins = "PORT279";
+				bias-pull-up;
+			};
+		};
+
+		scifa4_pins: scifa4 {
+			renesas,groups = "scifa4_data", "scifa4_ctrl";
+			renesas,function = "scifa4";
+		};
+	};
+
+Example 4: KZM-A9-GT (SH-Mobile AG5) default pin state for the MMCIF device
+
+	&mmcif {
+		pinctrl-0 = <&mmcif_pins>;
+		pinctrl-names = "default";
+
+		bus-width = <8>;
+		vmmc-supply = <&reg_1p8v>;
+		status = "okay";
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
new file mode 100644
index 000000000..388b21324
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt
@@ -0,0 +1,157 @@
+* Rockchip Pinmux Controller
+
+The Rockchip Pinmux Controller, enables the IC
+to share one PAD to several functional blocks. The sharing is done by
+multiplexing the PAD input/output signals. For each PAD there are several
+muxing options with option 0 being the use as a GPIO.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+The Rockchip pin configuration node is a node of a group of pins which can be
+used for a specific device or function. This node represents both mux and
+config of the pins in that group. The 'pins' selects the function mode(also
+named pin mode) this pin can work on and the 'config' configures various pad
+settings such as pull-up, etc.
+
+The pins are grouped into up to 5 individual pin banks which need to be
+defined as gpio sub-nodes of the pinmux controller.
+
+Required properties for iomux controller:
+  - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl"
+		       "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl"
+		       "rockchip,rk3288-pinctrl"
+  - rockchip,grf: phandle referencing a syscon providing the
+	 "general register files"
+
+Optional properties for iomux controller:
+  - rockchip,pmu: phandle referencing a syscon providing the pmu registers
+	 as some SoCs carry parts of the iomux controller registers there.
+	 Required for at least rk3188 and rk3288.
+
+Deprecated properties for iomux controller:
+  - reg: first element is the general register space of the iomux controller
+	 It should be large enough to contain also separate pull registers.
+	 second element is the separate pull register space of the rk3188.
+	 Use rockchip,grf and rockchip,pmu described above instead.
+
+Required properties for gpio sub nodes:
+  - compatible: "rockchip,gpio-bank"
+  - reg: register of the gpio bank (different than the iomux registerset)
+  - interrupts: base interrupt of the gpio bank in the interrupt controller
+  - clocks: clock that drives this bank
+  - gpio-controller: identifies the node as a gpio controller and pin bank.
+  - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+    binding is used, the amount of cells must be specified as 2. See generic
+    GPIO binding documentation for description of particular cells.
+  - interrupt-controller: identifies the controller node as interrupt-parent.
+  - #interrupt-cells: the value of this property should be 2 and the interrupt
+    cells should use the standard two-cell scheme described in
+    bindings/interrupt-controller/interrupts.txt
+
+Deprecated properties for gpio sub nodes:
+  - compatible: "rockchip,rk3188-gpio-bank0"
+  - reg: second element: separate pull register for rk3188 bank0, use
+	 rockchip,pmu described above instead
+
+Required properties for pin configuration node:
+  - rockchip,pins: 3 integers array, represents a group of pins mux and config
+    setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>.
+    The MUX 0 means gpio and MUX 1 to N mean the specific device function.
+    The phandle of a node containing the generic pinconfig options
+    to use, as described in pinctrl-bindings.txt in this directory.
+
+Examples:
+
+#include <dt-bindings/pinctrl/rockchip.h>
+
+...
+
+pinctrl@20008000 {
+	compatible = "rockchip,rk3066a-pinctrl";
+	rockchip,grf = <&grf>;
+
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	gpio0: gpio0@20034000 {
+		compatible = "rockchip,gpio-bank";
+		reg = <0x20034000 0x100>;
+		interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_gates8 9>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	...
+
+	pcfg_pull_default: pcfg_pull_default {
+		bias-pull-pin-default
+	};
+
+	uart2 {
+		uart2_xfer: uart2-xfer {
+			rockchip,pins = <RK_GPIO1 8 1 &pcfg_pull_default>,
+					<RK_GPIO1 9 1 &pcfg_pull_default>;
+		};
+	};
+};
+
+uart2: serial@20064000 {
+	compatible = "snps,dw-apb-uart";
+	reg = <0x20064000 0x400>;
+	interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+	reg-shift = <2>;
+	reg-io-width = <1>;
+	clocks = <&mux_uart2>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_xfer>;
+};
+
+Example for rk3188:
+
+	pinctrl@20008000 {
+		compatible = "rockchip,rk3188-pinctrl";
+		rockchip,grf = <&grf>;
+		rockchip,pmu = <&pmu>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio0: gpio0@0x2000a000 {
+			compatible = "rockchip,rk3188-gpio-bank0";
+			reg = <0x2000a000 0x100>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_gates8 9>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio1@0x2003c000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x2003c000 0x100>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_gates8 10>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		...
+
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
new file mode 100644
index 000000000..9d2a99529
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -0,0 +1,356 @@
+Samsung GPIO and Pin Mux/Config controller
+
+Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
+controller. It controls the input/output settings on the available pads/pins
+and also provides ability to multiplex and configure the output of various
+on-chip controllers onto these pads.
+
+Required Properties:
+- compatible: should be one of the following.
+  - "samsung,s3c2412-pinctrl": for S3C2412-compatible pin-controller,
+  - "samsung,s3c2416-pinctrl": for S3C2416-compatible pin-controller,
+  - "samsung,s3c2440-pinctrl": for S3C2440-compatible pin-controller,
+  - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller,
+  - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller,
+  - "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller,
+  - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller.
+  - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller.
+  - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller.
+  - "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller.
+  - "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller.
+  - "samsung,exynos7-pinctrl": for Exynos7 compatible pin-controller.
+
+- reg: Base address of the pin controller hardware module and length of
+  the address space it occupies.
+
+- Pin banks as child nodes: Pin banks of the controller are represented by child
+  nodes of the controller node. Bank name is taken from name of the node. Each
+  bank node must contain following properties:
+
+  - gpio-controller: identifies the node as a gpio controller and pin bank.
+  - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+    binding is used, the amount of cells must be specified as 2. See the below
+    mentioned gpio binding representation for description of particular cells.
+
+	Eg: <&gpx2 6 0>
+	<[phandle of the gpio controller node]
+	[pin number within the gpio controller]
+	[flags]>
+
+	Values for gpio specifier:
+	- Pin number: is a value between 0 to 7.
+	- Flags: 0 - Active High
+		 1 - Active Low
+
+- Pin mux/config groups as child nodes: The pin mux (selecting pin function
+  mode) and pin config (pull up/down, driver strength) settings are represented
+  as child nodes of the pin-controller node. There should be atleast one
+  child node and there is no limit on the count of these child nodes. It is
+  also possible for a child node to consist of several further child nodes
+  to allow grouping multiple pinctrl groups into one. The format of second
+  level child nodes is exactly the same as for first level ones and is
+  described below.
+
+  The child node should contain a list of pin(s) on which a particular pin
+  function selection or pin configuration (or both) have to applied. This
+  list of pins is specified using the property name "samsung,pins". There
+  should be atleast one pin specfied for this property and there is no upper
+  limit on the count of pins that can be specified. The pins are specified
+  using pin names which are derived from the hardware manual of the SoC. As
+  an example, the pins in GPA0 bank of the pin controller can be represented
+  as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
+  The format of the pin names should be (as per the hardware manual)
+  "[pin bank name]-[pin number within the bank]".
+
+  The pin function selection that should be applied on the pins listed in the
+  child node is specified using the "samsung,pin-function" property. The value
+  of this property that should be applied to each of the pins listed in the
+  "samsung,pins" property should be picked from the hardware manual of the SoC
+  for the specified pin group. This property is optional in the child node if
+  no specific function selection is desired for the pins listed in the child
+  node. The value of this property is used as-is to program the pin-controller
+  function selector register of the pin-bank.
+
+  The child node can also optionally specify one or more of the pin
+  configuration that should be applied on all the pins listed in the
+  "samsung,pins" property of the child node. The following pin configuration
+  properties are supported.
+
+  - samsung,pin-val: Initial value of pin output buffer.
+  - samsung,pin-pud: Pull up/down configuration.
+  - samsung,pin-drv: Drive strength configuration.
+  - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
+  - samsung,pin-drv-pdn: Drive strength configuration in power down mode.
+
+  The values specified by these config properties should be derived from the
+  hardware manual and these values are programmed as-is into the pin
+  pull up/down and driver strength register of the pin-controller.
+
+  Note: A child should include atleast a pin function selection property or
+  pin configuration property (one or more) or both.
+
+  The client nodes that require a particular pin function selection and/or
+  pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
+  file.
+
+External GPIO and Wakeup Interrupts:
+
+The controller supports two types of external interrupts over gpio. The first
+is the external gpio interrupt and second is the external wakeup interrupts.
+The difference between the two is that the external wakeup interrupts can be
+used as system wakeup events.
+
+A. External GPIO Interrupts: For supporting external gpio interrupts, the
+   following properties should be specified in the pin-controller device node.
+
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     GPIO interrupts are forwarded to.
+   - interrupts: interrupt specifier for the controller. The format and value of
+     the interrupt specifier depends on the interrupt parent for the controller.
+
+   In addition, following properties must be present in node of every bank
+   of pins supporting GPIO interrupts:
+
+   - interrupt-controller: identifies the controller node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2.
+     - First Cell: represents the external gpio interrupt number local to the
+       external gpio interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+
+B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
+   child node representing the external wakeup interrupt controller should be
+   included in the pin-controller device node. This child node should include
+   the following properties.
+
+   - compatible: identifies the type of the external wakeup interrupt controller
+     The possible values are:
+     - samsung,s3c2410-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung S3C24xx SoCs except S3C2412 and S3C2413,
+     - samsung,s3c2412-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung S3C2412 and S3C2413 SoCs,
+     - samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung S3C64xx SoCs,
+     - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung Exynos4210 and S5PC110/S5PV210 SoCs.
+     - samsung,exynos7-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung Exynos7 SoC.
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     wakeup interrupts are forwarded to.
+   - interrupts: interrupt used by multiplexed wakeup interrupts.
+
+   In addition, following properties must be present in node of every bank
+   of pins supporting wake-up interrupts:
+
+   - interrupt-controller: identifies the node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2
+     - First Cell: represents the external wakeup interrupt number local to
+       the external wakeup interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+
+   Node of every bank of pins supporting direct wake-up interrupts (without
+   multiplexing) must contain following properties:
+
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     wakeup interrupts are forwarded to.
+   - interrupts: interrupts of the interrupt parent which are used for external
+     wakeup interrupts from pins of the bank, must contain interrupts for all
+     pins of the bank.
+
+Aliases:
+
+All the pin controller nodes should be represented in the aliases node using
+the following format 'pinctrl{n}' where n is a unique number for the alias.
+
+Aliases for controllers compatible with "samsung,exynos7-pinctrl":
+- pinctrl0: pin controller of ALIVE block,
+- pinctrl1: pin controller of BUS0 block,
+- pinctrl2: pin controller of NFC block,
+- pinctrl3: pin controller of TOUCH block,
+- pinctrl4: pin controller of FF block,
+- pinctrl5: pin controller of ESE block,
+- pinctrl6: pin controller of FSYS0 block,
+- pinctrl7: pin controller of FSYS1 block,
+- pinctrl8: pin controller of BUS1 block,
+- pinctrl9: pin controller of AUDIO block,
+
+Example: A pin-controller node with pin banks:
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,exynos4210-pinctrl";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		/* ... */
+
+		/* Pin bank without external interrupts */
+		gpy0: gpy0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		/* ... */
+
+		/* Pin bank with external GPIO or muxed wake-up interrupts */
+		gpj0: gpj0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		/* ... */
+
+		/* Pin bank with external direct wake-up interrupts */
+		gpx0: gpx0 {
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+				     <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>;
+			#interrupt-cells = <2>;
+		};
+
+		/* ... */
+	};
+
+Example 1: A pin-controller node with pin groups.
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,exynos4210-pinctrl";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		/* ... */
+
+		uart0_data: uart0-data {
+			samsung,pins = "gpa0-0", "gpa0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart0_fctl: uart0-fctl {
+			samsung,pins = "gpa0-2", "gpa0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_data: uart1-data {
+			samsung,pins = "gpa0-4", "gpa0-5";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_fctl: uart1-fctl {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c2_bus: i2c2-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_bus8: sd4-bus-width8 {
+			part-1 {
+				samsung,pins = "gpk0-3", "gpk0-4",
+						"gpk0-5", "gpk0-6";
+				samsung,pin-function = <3>;
+				samsung,pin-pud = <3>;
+				samsung,pin-drv = <3>;
+			};
+			part-2 {
+				samsung,pins = "gpk1-3", "gpk1-4",
+						"gpk1-5", "gpk1-6";
+				samsung,pin-function = <4>;
+				samsung,pin-pud = <4>;
+				samsung,pin-drv = <3>;
+			};
+		};
+	};
+
+Example 2: A pin-controller node with external wakeup interrupt controller node.
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,exynos4210-pinctrl";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>
+
+		/* ... */
+
+		wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupts = <0 32 0>;
+		};
+	};
+
+Example 3: A uart client node that supports 'default' and 'flow-control' states.
+
+	uart@13800000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13800000 0x100>;
+		interrupts = <0 52 0>;
+		pinctrl-names = "default", "flow-control;
+		pinctrl-0 = <&uart0_data>;
+		pinctrl-1 = <&uart0_data &uart0_fctl>;
+	};
+
+Example 4: Set up the default pin state for uart controller.
+
+	static int s3c24xx_serial_probe(struct platform_device *pdev) {
+		struct pinctrl *pinctrl;
+
+		/* ... */
+
+		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
+	}
+
+Example 5: A display port client node that supports 'default' pinctrl state
+	   and gpio binding.
+
+	display-port-controller {
+		/* ... */
+
+		samsung,hpd-gpio = <&gpx2 6 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dp_hpd>;
+	};
+
+Example 6: Request the gpio for display port controller
+
+	static int exynos_dp_probe(struct platform_device *pdev)
+	{
+		int hpd_gpio, ret;
+		struct device *dev = &pdev->dev;
+		struct device_node *dp_node = dev->of_node;
+
+		/* ... */
+
+		hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0);
+
+		/* ... */
+
+		ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN,
+					    "hpd_gpio");
+		/* ... */
+	}
diff --git a/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt b/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt
new file mode 100644
index 000000000..876974204
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt
@@ -0,0 +1,318 @@
+ST Ericsson abx500 pinmux controller
+
+Required properties:
+- compatible: "stericsson,ab8500-gpio",  "stericsson,ab8540-gpio",
+	      "stericsson,ab8505-gpio", "stericsson,ab9540-gpio",
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+ST Ericsson's pin configuration nodes use the generic pin multiplexing
+and pin configuration bindings, see pinctrl-bindings.txt
+
+Example board file extract:
+
+&pinctrl_abx500 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sysclkreq2_default_mode>, <&sysclkreq3_default_mode>, <&gpio3_default_mode>, <&sysclkreq6_default_mode>, <&pwmout1_default_mode>, <&pwmout2_default_mode>, <&pwmout3_default_mode>, <&adi1_default_mode>, <&dmic12_default_mode>, <&dmic34_default_mode>, <&dmic56_default_mode>, <&sysclkreq5_default_mode>, <&batremn_default_mode>, <&service_default_mode>, <&pwrctrl0_default_mode>, <&pwrctrl1_default_mode>, <&pwmextvibra1_default_mode>, <&pwmextvibra2_default_mode>, <&gpio51_default_mode>, <&gpio52_default_mode>, <&gpio53_default_mode>, <&gpio54_default_mode>, <&pdmclkdat_default_mode>;
+
+	sysclkreq2 {
+		sysclkreq2_default_mode: sysclkreq2_default {
+			default_mux {
+				function = "sysclkreq";
+				groups = "sysclkreq2_d_1";
+			};
+			default_cfg {
+				pins = "GPIO1";
+				bias-disable;
+			};
+		};
+	};
+	sysclkreq3 {
+		sysclkreq3_default_mode: sysclkreq3_default {
+			default_mux {
+				function = "sysclkreq";
+				groups = "sysclkreq3_d_1";
+			};
+			default_cfg {
+				pins = "GPIO2";
+				output-low;
+			};
+		};
+	};
+	gpio3 {
+		gpio3_default_mode: gpio3_default {
+			default_mux {
+				function = "gpio";
+				groups = "gpio3_a_1";
+			};
+			default_cfg {
+				pins = "GPIO3";
+				output-low;
+			};
+		};
+	};
+	sysclkreq6 {
+		sysclkreq6_default_mode: sysclkreq6_default {
+			default_mux {
+				function = "sysclkreq";
+				groups = "sysclkreq6_d_1";
+			};
+			default_cfg {
+				pins = "GPIO4";
+				bias-disable;
+			};
+		};
+	};
+	pwmout1 {
+		pwmout1_default_mode: pwmout1_default {
+			default_mux {
+				function = "pwmout";
+				groups = "pwmout1_d_1";
+			};
+			default_cfg {
+				pins = "GPIO14";
+				output-low;
+			};
+		};
+	};
+	pwmout2 {
+		pwmout2_default_mode: pwmout2_default {
+			pwmout2_default_mux {
+				function = "pwmout";
+				groups = "pwmout2_d_1";
+			};
+			pwmout2_default_cfg {
+				pins = "GPIO15";
+				output-low;
+			};
+		};
+	};
+	pwmout3 {
+		pwmout3_default_mode: pwmout3_default {
+			pwmout3_default_mux {
+				function = "pwmout";
+				groups = "pwmout3_d_1";
+			};
+			pwmout3_default_cfg {
+				pins = "GPIO16";
+				output-low;
+			};
+		};
+	};
+	adi1 {
+
+		adi1_default_mode: adi1_default {
+			adi1_default_mux {
+				function = "adi1";
+				groups = "adi1_d_1";
+			};
+			adi1_default_cfg1 {
+				pins = "GPIO17","GPIO19","GPIO20";
+				bias-disable;
+			};
+			adi1_default_cfg2 {
+				pins = "GPIO18";
+				output-low;
+			};
+		};
+	};
+	dmic12 {
+		dmic12_default_mode: dmic12_default {
+			dmic12_default_mux {
+				function = "dmic";
+				groups = "dmic12_d_1";
+			};
+			dmic12_default_cfg1 {
+				pins = "GPIO27";
+				output-low;
+			};
+			dmic12_default_cfg2 {
+				pins = "GPIO28";
+				bias-disable;
+			};
+		};
+	};
+	dmic34 {
+		dmic34_default_mode: dmic34_default {
+			dmic34_default_mux {
+				function = "dmic";
+				groups = "dmic34_d_1";
+			};
+			dmic34_default_cfg1 {
+				pins = "GPIO29";
+				output-low;
+			};
+			dmic34_default_cfg2 {
+				pins = "GPIO30";
+				bias-disable;{
+
+			};
+		};
+	};
+	dmic56 {
+		dmic56_default_mode: dmic56_default {
+			dmic56_default_mux {
+				function = "dmic";
+				groups = "dmic56_d_1";
+			};
+			dmic56_default_cfg1 {
+				pins = "GPIO31";
+				output-low;
+			};
+			dmic56_default_cfg2 {
+				pins = "GPIO32";
+				bias-disable;
+			};
+		};
+	};
+	sysclkreq5 {
+		sysclkreq5_default_mode: sysclkreq5_default {
+			sysclkreq5_default_mux {
+				function = "sysclkreq";
+				groups = "sysclkreq5_d_1";
+			};
+			sysclkreq5_default_cfg {
+				pins = "GPIO42";
+				output-low;
+			};
+		};
+	};
+	batremn {
+		batremn_default_mode: batremn_default {
+			batremn_default_mux {
+				function = "batremn";
+				groups = "batremn_d_1";
+			};
+			batremn_default_cfg {
+				pins = "GPIO43";
+				bias-disable;
+			};
+		};
+	};
+	service {
+		service_default_mode: service_default {
+			service_default_mux {
+				function = "service";
+				groups = "service_d_1";
+			};
+			service_default_cfg {
+				pins = "GPIO44";
+				bias-disable;
+			};
+		};
+	};
+	pwrctrl0 {
+		pwrctrl0_default_mux: pwrctrl0_mux {
+			pwrctrl0_default_mux {
+				function = "pwrctrl";
+				groups = "pwrctrl0_d_1";
+			};
+		};
+		pwrctrl0_default_mode: pwrctrl0_default {
+			pwrctrl0_default_cfg {
+				pins = "GPIO45";
+				bias-disable;
+			};
+		};
+	};
+	pwrctrl1 {
+		pwrctrl1_default_mux: pwrctrl1_mux {
+			pwrctrl1_default_mux {
+				function = "pwrctrl";
+				groups = "pwrctrl1_d_1";
+			};
+		};
+		pwrctrl1_default_mode: pwrctrl1_default {
+			pwrctrl1_default_cfg {
+				pins = "GPIO46";
+				bias-disable;
+			};
+		};
+	};
+	pwmextvibra1 {
+		pwmextvibra1_default_mode: pwmextvibra1_default {
+			pwmextvibra1_default_mux {
+				function = "pwmextvibra";
+				groups = "pwmextvibra1_d_1";
+			};
+			pwmextvibra1_default_cfg {
+				pins = "GPIO47";
+				bias-disable;
+			};
+		};
+	};
+	pwmextvibra2 {
+		pwmextvibra2_default_mode: pwmextvibra2_default {
+			pwmextvibra2_default_mux {
+				function = "pwmextvibra";
+				groups = "pwmextvibra2_d_1";
+			};
+			pwmextvibra1_default_cfg {
+				pins = "GPIO48";
+				bias-disable;
+			};
+		};
+	};
+	gpio51 {
+		gpio51_default_mode: gpio51_default {
+				gpio51_default_mux {
+				function = "gpio";
+				groups = "gpio51_a_1";
+			};
+			gpio51_default_cfg {
+				pins = "GPIO51";
+				output-low;
+			};
+		};
+	};
+	gpio52 {
+		gpio52_default_mode: gpio52_default {
+			gpio52_default_mux {
+				function = "gpio";
+				groups = "gpio52_a_1";
+			};
+			gpio52_default_cfg {
+				pins = "GPIO52";
+				bias-pull-down;
+			};
+		};
+	};
+	gpio53 {
+		gpio53_default_mode: gpio53_default {
+			gpio53_default_mux {
+				function = "gpio";
+				groups = "gpio53_a_1";
+			};
+			gpio53_default_cfg {
+				pins = "GPIO53";
+				bias-pull-down;
+			};
+		};
+	};
+	gpio54 {
+		gpio54_default_mode: gpio54_default {
+			gpio54_default_mux {
+				function = "gpio";
+				groups = "gpio54_a_1";
+			};
+			gpio54_default_cfg {
+				pins = "GPIO54";
+				output-low;
+			};
+		};
+	};
+	pdmclkdat {
+		pdmclkdat_default_mode: pdmclkdat_default {
+			pdmclkdat_default_mux {
+				function = "pdm";
+				groups = "pdmclkdat_d_1";
+			};
+			pdmclkdat_default_cfg {
+				pins = "GPIO55", "GPIO56";
+				bias-disable;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt
new file mode 100644
index 000000000..f63fcb3ed
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt
@@ -0,0 +1,145 @@
+ST Ericsson Nomadik pinmux controller
+
+Required properties:
+- compatible: "stericsson,db8500-pinctrl", "stericsson,db8540-pinctrl",
+              "stericsson,stn8815-pinctrl"
+- reg: Should contain the register physical address and length of the PRCMU.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+ST Ericsson's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as input, output, pull up, pull down...
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content. The subnodes use the generic
+pin multiplexing node layout from the standard pin control bindings
+(see pinctrl-bindings.txt):
+
+Required pin multiplexing subnode properties:
+- function: A string containing the name of the function to mux to the
+  pin or group.
+- groups : An array of strings. Each string contains the name of a pin
+  group that will be combined with the function to form a multiplexing
+  set-up.
+
+Required pin configuration subnode properties:
+- pins: A string array describing the pins affected by the configuration
+  in the node.
+- ste,config: Handle of pin configuration node
+  (e.g. ste,config = <&slpm_in_wkup_pdis>)
+
+- ste,input : <0/1/2>
+	0: input with no pull
+	1: input with pull up,
+	2: input with pull down,
+
+- ste,output: <0/1/2>
+	0: output low,
+	1: output high,
+	2: output (value is not specified).
+
+- ste,sleep: <0/1>
+	0: sleep mode disable,
+	1: sleep mode enable.
+
+- ste,sleep-input: <0/1/2/3>
+	0: sleep input with no pull,
+	1: sleep input with pull up,
+	2: sleep input with pull down.
+	3: sleep input and keep last input configuration (no pull, pull up or pull down).
+
+- ste,sleep-output: <0/1/2>
+	0: sleep output low,
+	1: sleep output high,
+	2: sleep output (value is not specified).
+
+- ste,sleep-gpio: <0/1>
+	0: disable sleep gpio mode,
+	1: enable sleep gpio mode.
+
+- ste,sleep-wakeup: <0/1>
+	0: wake-up detection enabled,
+	1: wake-up detection disabled.
+
+- ste,sleep-pull-disable: <0/1>
+	0: GPIO pull-up or pull-down resistor is enabled, when pin is an input,
+	1: GPIO pull-up and pull-down resistor are disabled.
+
+Example board file extract:
+
+	pinctrl@80157000 {
+		compatible = "stericsson,db8500-pinctrl";
+		reg = <0x80157000 0x2000>;
+
+		pinctrl-names = "default";
+
+		slpm_in_wkup_pdis: slpm_in_wkup_pdis {
+			ste,sleep = <1>;
+			ste,sleep-input = <3>;
+			ste,sleep-wakeup = <1>;
+			ste,sleep-pull-disable = <0>;
+		};
+
+		slpm_out_hi_wkup_pdis: slpm_out_hi_wkup_pdis {
+			ste,sleep = <1>;
+			ste,sleep-output = <1>;
+			ste,sleep-wakeup = <1>;
+			ste,sleep-pull-disable = <0>;
+		};
+
+		slpm_out_wkup_pdis: slpm_out_wkup_pdis {
+			ste,sleep = <1>;
+			ste,sleep-output = <2>;
+			ste,sleep-wakeup = <1>;
+			ste,sleep-pull-disable = <0>;
+		};
+
+		uart0 {
+			uart0_default_mux: uart0_mux {
+				u0_default_mux {
+					function = "u0";
+					pins = "u0_a_1";
+				};
+			};
+			uart0_default_mode: uart0_default {
+				uart0_default_cfg1 {
+					pins = "GPIO0", "GPIO2";
+					ste,input = <1>;
+				};
+
+				uart0_default_cfg2 {
+					pins = "GPIO1", "GPIO3";
+					ste,output = <1>;
+				};
+			};
+			uart0_sleep_mode: uart0_sleep {
+				uart0_sleep_cfg1 {
+					pins = "GPIO0", "GPIO2";
+					ste,config = <&slpm_in_wkup_pdis>;
+				};
+				uart0_sleep_cfg2 {
+					pins = "GPIO1";
+					ste,config = <&slpm_out_hi_wkup_pdis>;
+				};
+				uart0_sleep_cfg3 {
+					pins = "GPIO3";
+					ste,config = <&slpm_out_wkup_pdis>;
+				};
+			};
+		};
+	};
+
+	uart@80120000 {
+		compatible = "arm,pl011", "arm,primecell";
+		reg = <0x80120000 0x1000>;
+		interrupts = <0 11 0x4>;
+
+		pinctrl-names = "default","sleep";
+		pinctrl-0 = <&uart0_default_mux>, <&uart0_default_mode>;
+		pinctrl-1 = <&uart0_sleep_mode>;
+	};
diff --git a/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt
new file mode 100644
index 000000000..88c80273d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/ti,omap-pinctrl.txt
@@ -0,0 +1,13 @@
+OMAP Pinctrl definitions
+
+Required properties:
+- compatible : Should be one of:
+  "ti,omap2420-padconf" - OMAP2420 compatible pinctrl
+  "ti,omap2430-padconf" - OMAP2430 compatible pinctrl
+  "ti,omap3-padconf" - OMAP3 compatible pinctrl
+  "ti,omap4-padconf" - OMAP4 compatible pinctrl
+  "ti,omap5-padconf" - OMAP5 compatible pinctrl
+  "ti,dra7-padconf" - DRA7 compatible pinctrl
+  "ti,am437-padconf" - AM437x compatible pinctrl
+
+See Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt for further details.
diff --git a/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt
new file mode 100644
index 000000000..b7b55a964
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.txt
@@ -0,0 +1,104 @@
+	Binding for Xilinx Zynq Pinctrl
+
+Required properties:
+- compatible: "xlnx,zynq-pinctrl"
+- syscon: phandle to SLCR
+- reg: Offset and length of pinctrl space in SLCR
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Zynq's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, slew rate, etc.
+
+Each configuration node can consist of multiple nodes describing the pinmux and
+pinconf options. Those nodes can be pinmux nodes or pinconf nodes.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Required properties for pinmux nodes are:
+ - groups: A list of pinmux groups.
+ - function: The name of a pinmux function to activate for the specified set
+   of groups.
+
+Required properties for configuration nodes:
+One of:
+ - pins: a list of pin names
+ - groups: A list of pinmux groups.
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pinmux subnode:
+ groups, function
+
+The following generic properties as defined in pinctrl-bindings.txt are valid
+to specify in a pinconf subnode:
+ groups, pins, bias-disable, bias-high-impedance, bias-pull-up, slew-rate,
+ low-power-disable, low-power-enable
+
+ Valid arguments for 'slew-rate' are '0' and '1' to select between slow and fast
+ respectively.
+
+ Valid values for groups are:
+   ethernet0_0_grp, ethernet1_0_grp, mdio0_0_grp, mdio1_0_grp,
+   qspi0_0_grp, qspi1_0_grp, qspi_fbclk, qspi_cs1_grp, spi0_0_grp,
+   spi0_1_grp - spi0_2_grp, spi1_0_grp - spi1_3_grp, sdio0_0_grp - sdio0_2_grp,
+   sdio1_0_grp - sdio1_3_grp, sdio0_emio_wp, sdio0_emio_cd, sdio1_emio_wp,
+   sdio1_emio_cd, smc0_nor, smc0_nor_cs1_grp, smc0_nor_addr25_grp, smc0_nand,
+   can0_0_grp - can0_10_grp, can1_0_grp - can1_11_grp, uart0_0_grp - uart0_10_grp,
+   uart1_0_grp - uart1_11_grp, i2c0_0_grp - i2c0_10_grp, i2c1_0_grp - i2c1_10_grp,
+   ttc0_0_grp - ttc0_2_grp, ttc1_0_grp - ttc1_2_grp, swdt0_0_grp - swdt0_4_grp,
+   gpio0_0_grp - gpio0_53_grp, usb0_0_grp, usb1_0_grp
+
+ Valid values for pins are:
+   MIO0 - MIO53
+
+ Valid values for function are:
+   ethernet0, ethernet1, mdio0, mdio1, qspi0, qspi1, qspi_fbclk, qspi_cs1,
+   spi0, spi1, sdio0, sdio0_pc, sdio0_cd, sdio0_wp,
+   sdio1, sdio1_pc, sdio1_cd, sdio1_wp,
+   smc0_nor, smc0_nor_cs1, smc0_nor_addr25, smc0_nand, can0, can1, uart0, uart1,
+   i2c0, i2c1, ttc0, ttc1, swdt0, gpio0, usb0, usb1
+
+The following driver-specific properties as defined here are valid to specify in
+a pin configuration subnode:
+ - io-standard: Configure the pin to use the selected IO standard according to
+   this mapping:
+    1: LVCMOS18
+    2: LVCMOS25
+    3: LVCMOS33
+    4: HSTL
+
+Example:
+	pinctrl0: pinctrl@700 {
+		compatible = "xlnx,pinctrl-zynq";
+		reg = <0x700 0x200>;
+		syscon = <&slcr>;
+
+		pinctrl_uart1_default: uart1-default {
+			mux {
+				groups = "uart1_10_grp";
+				function = "uart1";
+			};
+
+			conf {
+				groups = "uart1_10_grp";
+				slew-rate = <0>;
+				io-standard = <1>;
+			};
+
+			conf-rx {
+				pins = "MIO49";
+				bias-high-impedance;
+			};
+
+			conf-tx {
+				pins = "MIO48";
+				bias-disable;
+			};
+		};
+	};