Initial import

17 files changed, 678 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/power/bq2415x.txt b/Documentation/devicetree/bindings/power/bq2415x.txt
new file mode 100644
index 000000000..d0327f0b5
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/bq2415x.txt
@@ -0,0 +1,47 @@
+Binding for TI bq2415x Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "ti,bq24150"
+ * "ti,bq24150"
+ * "ti,bq24150a"
+ * "ti,bq24151"
+ * "ti,bq24151a"
+ * "ti,bq24152"
+ * "ti,bq24153"
+ * "ti,bq24153a"
+ * "ti,bq24155"
+ * "ti,bq24156"
+ * "ti,bq24156a"
+ * "ti,bq24158"
+- reg:			   integer, i2c address of the device.
+- ti,current-limit:	   integer, initial maximum current charger can pull
+			   from power supply in mA.
+- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV.
+			   The chip will use slow precharge if battery voltage
+			   is below this value.
+- ti,battery-regulation-voltage: integer, maximum charging voltage in mV.
+- ti,charge-current:	   integer, maximum charging current in mA.
+- ti,termination-current:  integer, charge will be terminated when current in
+			   constant-voltage phase drops below this value (in mA).
+- ti,resistor-sense:	   integer, value of sensing resistor in milliohm.
+
+Optional properties:
+- ti,usb-charger-detection: phandle to usb charger detection device.
+			    (required for auto mode)
+
+Example from Nokia N900:
+
+bq24150a {
+	compatible = "ti,bq24150a";
+	reg = <0x6b>;
+
+	ti,current-limit = <100>;
+	ti,weak-battery-voltage = <3400>;
+	ti,battery-regulation-voltage = <4200>;
+	ti,charge-current = <650>;
+	ti,termination-current = <100>;
+	ti,resistor-sense = <68>;
+
+	ti,usb-charger-detection = <&isp1704>;
+};
diff --git a/Documentation/devicetree/bindings/power/da9150-charger.txt b/Documentation/devicetree/bindings/power/da9150-charger.txt
new file mode 100644
index 000000000..f3906663c
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/da9150-charger.txt
@@ -0,0 +1,26 @@
+Dialog Semiconductor DA9150 Charger Power Supply bindings
+
+Required properties:
+- compatible: "dlg,da9150-charger" for DA9150 Charger Power Supply
+
+Optional properties:
+- io-channels: List of phandle and IIO specifier pairs
+- io-channel-names: List of channel names used by charger
+      ["CHAN_IBUS", "CHAN_VBUS", "CHAN_TJUNC", "CHAN_VBAT"]
+  (See Documentation/devicetree/bindings/iio/iio-bindings.txt for further info)
+
+
+Example:
+
+	da9150-charger {
+		compatible = "dlg,da9150-charger";
+
+		io-channels = <&gpadc 0>,
+			      <&gpadc 2>,
+			      <&gpadc 8>,
+			      <&gpadc 5>;
+		io-channel-names = "CHAN_IBUS",
+				   "CHAN_VBUS",
+				   "CHAN_TJUNC",
+				   "CHAN_VBAT";
+	};
diff --git a/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt b/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt
new file mode 100644
index 000000000..65cc03457
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/fsl,imx-gpc.txt
@@ -0,0 +1,59 @@
+Freescale i.MX General Power Controller
+=======================================
+
+The i.MX6Q General Power Control (GPC) block contains DVFS load tracking
+counters and Power Gating Control (PGC) for the CPU and PU (GPU/VPU) power
+domains.
+
+Required properties:
+- compatible: Should be "fsl,imx6q-gpc" or "fsl,imx6sl-gpc"
+- reg: should be register base and length as documented in the
+  datasheet
+- interrupts: Should contain GPC interrupt request 1
+- pu-supply: Link to the LDO regulator powering the PU power domain
+- clocks: Clock phandles to devices in the PU power domain that need
+	  to be enabled during domain power-up for reset propagation.
+- #power-domain-cells: Should be 1, see below:
+
+The gpc node is a power-controller as documented by the generic power domain
+bindings in Documentation/devicetree/bindings/power/power_domain.txt.
+
+Example:
+
+	gpc: gpc@020dc000 {
+		compatible = "fsl,imx6q-gpc";
+		reg = <0x020dc000 0x4000>;
+		interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 90 IRQ_TYPE_LEVEL_HIGH>;
+		pu-supply = <&reg_pu>;
+		clocks = <&clks IMX6QDL_CLK_GPU3D_CORE>,
+			 <&clks IMX6QDL_CLK_GPU3D_SHADER>,
+			 <&clks IMX6QDL_CLK_GPU2D_CORE>,
+			 <&clks IMX6QDL_CLK_GPU2D_AXI>,
+			 <&clks IMX6QDL_CLK_OPENVG_AXI>,
+			 <&clks IMX6QDL_CLK_VPU_AXI>;
+		#power-domain-cells = <1>;
+	};
+
+
+Specifying power domain for IP modules
+======================================
+
+IP cores belonging to a power domain should contain a 'power-domains' property
+that is a phandle pointing to the gpc device node and a DOMAIN_INDEX specifying
+the power domain the device belongs to.
+
+Example of a device that is part of the PU power domain:
+
+	vpu: vpu@02040000 {
+		reg = <0x02040000 0x3c000>;
+		/* ... */
+		power-domains = <&gpc 1>;
+		/* ... */
+	};
+
+The following DOMAIN_INDEX values are valid for i.MX6Q:
+ARM_DOMAIN     0
+PU_DOMAIN      1
+The following additional DOMAIN_INDEX value is valid for i.MX6SL:
+DISPLAY_DOMAIN 2
diff --git a/Documentation/devicetree/bindings/power/isp1704.txt b/Documentation/devicetree/bindings/power/isp1704.txt
new file mode 100644
index 000000000..fa3596907
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/isp1704.txt
@@ -0,0 +1,17 @@
+Binding for NXP ISP1704 USB Charger Detection
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "nxp,isp1704"
+- nxp,enable-gpio: Should contain a phandle + gpio-specifier
+  to the GPIO pin connected to the chip's enable pin.
+- usb-phy: Should contain a phandle to the USB PHY
+  the ISP1704 is connected to.
+
+Example:
+
+isp1704 {
+	compatible = "nxp,isp1704";
+	nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
+	usb-phy = <&usb2_phy>;
+};
diff --git a/Documentation/devicetree/bindings/power/ltc2941.txt b/Documentation/devicetree/bindings/power/ltc2941.txt
new file mode 100644
index 000000000..ea42ae12d
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/ltc2941.txt
@@ -0,0 +1,27 @@
+binding for LTC2941 and LTC2943 battery gauges
+
+Both the LTC2941 and LTC2943 measure battery capacity.
+The LTC2943 is compatible with the LTC2941, it adds voltage and
+temperature monitoring, and uses a slightly different conversion
+formula for the charge counter.
+
+Required properties:
+- compatible: Should contain "ltc2941" or "ltc2943" which also indicates the
+    type of I2C chip attached.
+- reg: The 7-bit I2C address.
+- lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit
+    negative value when the battery has been connected to the wrong end of the
+    resistor.
+- lltc,prescaler-exponent: The prescaler exponent as explained in the datasheet.
+    This determines the range and accuracy of the gauge. The value is programmed
+    into the chip only if it differs from the current setting. The setting is
+    lost when the battery is disconnected.
+
+Example from the Topic Miami Florida board:
+
+	fuelgauge: ltc2943@64 {
+		compatible = "ltc2943";
+		reg = <0x64>;
+		lltc,resistor-sense = <15>;
+		lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */
+	};
diff --git a/Documentation/devicetree/bindings/power/opp.txt b/Documentation/devicetree/bindings/power/opp.txt
new file mode 100644
index 000000000..74499e503
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/opp.txt
@@ -0,0 +1,25 @@
+* Generic OPP Interface
+
+SoCs have a standard set of tuples consisting of frequency and
+voltage pairs that the device will support per voltage domain. These
+are called Operating Performance Points or OPPs.
+
+Properties:
+- operating-points: An array of 2-tuples items, and each item consists
+  of frequency and voltage like <freq-kHz vol-uV>.
+	freq: clock frequency in kHz
+	vol: voltage in microvolt
+
+Examples:
+
+cpu@0 {
+	compatible = "arm,cortex-a9";
+	reg = <0>;
+	next-level-cache = <&L2>;
+	operating-points = <
+		/* kHz    uV */
+		792000  1100000
+		396000  950000
+		198000  850000
+	>;
+};
diff --git a/Documentation/devicetree/bindings/power/power-controller.txt b/Documentation/devicetree/bindings/power/power-controller.txt
new file mode 100644
index 000000000..4f7a3bc9c
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/power-controller.txt
@@ -0,0 +1,18 @@
+* Generic system power control capability
+
+Power-management integrated circuits or miscellaneous hardware components are
+sometimes able to control the system power. The device driver associated with these
+components might need to define this capability, which tells the kernel that
+it can be used to switch off the system. The corresponding device must have the
+standard property "system-power-controller" in its device node. This property
+marks the device as able to control the system power. In order to test if this
+property is found programmatically, use the helper function
+"of_device_is_system_power_controller" from of.h .
+
+Example:
+
+act8846: act8846@5 {
+	 compatible = "active-semi,act8846";
+	 status = "okay";
+	 system-power-controller;
+}
diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt
new file mode 100644
index 000000000..0f8ed3710
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/power_domain.txt
@@ -0,0 +1,78 @@
+* Generic PM domains
+
+System on chip designs are often divided into multiple PM domains that can be
+used for power gating of selected IP blocks for power saving by reduced leakage
+current.
+
+This device tree binding can be used to bind PM domain consumer devices with
+their PM domains provided by PM domain providers. A PM domain provider can be
+represented by any node in the device tree and can provide one or more PM
+domains. A consumer node can refer to the provider by a phandle and a set of
+phandle arguments (so called PM domain specifiers) of length specified by the
+#power-domain-cells property in the PM domain provider node.
+
+==PM domain providers==
+
+Required properties:
+ - #power-domain-cells : Number of cells in a PM domain specifier;
+   Typically 0 for nodes representing a single PM domain and 1 for nodes
+   providing multiple PM domains (e.g. power controllers), but can be any value
+   as specified by device tree binding documentation of particular provider.
+
+Optional properties:
+ - power-domains : A phandle and PM domain specifier as defined by bindings of
+                   the power controller specified by phandle.
+   Some power domains might be powered from another power domain (or have
+   other hardware specific dependencies). For representing such dependency
+   a standard PM domain consumer binding is used. When provided, all domains
+   created by the given provider should be subdomains of the domain
+   specified by this binding. More details about power domain specifier are
+   available in the next section.
+
+Example:
+
+	power: power-controller@12340000 {
+		compatible = "foo,power-controller";
+		reg = <0x12340000 0x1000>;
+		#power-domain-cells = <1>;
+	};
+
+The node above defines a power controller that is a PM domain provider and
+expects one cell as its phandle argument.
+
+Example 2:
+
+	parent: power-controller@12340000 {
+		compatible = "foo,power-controller";
+		reg = <0x12340000 0x1000>;
+		#power-domain-cells = <1>;
+	};
+
+	child: power-controller@12340000 {
+		compatible = "foo,power-controller";
+		reg = <0x12341000 0x1000>;
+		power-domains = <&parent 0>;
+		#power-domain-cells = <1>;
+	};
+
+The nodes above define two power controllers: 'parent' and 'child'.
+Domains created by the 'child' power controller are subdomains of '0' power
+domain provided by the 'parent' power controller.
+
+==PM domain consumers==
+
+Required properties:
+ - power-domains : A phandle and PM domain specifier as defined by bindings of
+                   the power controller specified by phandle.
+
+Example:
+
+	leaky-device@12350000 {
+		compatible = "foo,i-leak-current";
+		reg = <0x12350000 0x1000>;
+		power-domains = <&power 0>;
+	};
+
+The node above defines a typical PM domain consumer device, which is located
+inside a PM domain with index 0 of a power controller represented by a node
+with the label "power".
diff --git a/Documentation/devicetree/bindings/power/renesas,sysc-rmobile.txt b/Documentation/devicetree/bindings/power/renesas,sysc-rmobile.txt
new file mode 100644
index 000000000..beda7d2ef
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/renesas,sysc-rmobile.txt
@@ -0,0 +1,100 @@
+DT bindings for the Renesas R-Mobile System Controller
+
+== System Controller Node ==
+
+The R-Mobile System Controller provides the following functions:
+  - Boot mode management,
+  - Reset generation,
+  - Power management.
+
+Required properties:
+- compatible: Should be "renesas,sysc-<soctype>", "renesas,sysc-rmobile" as
+	      fallback.
+	      Examples with soctypes are:
+		- "renesas,sysc-r8a73a4" (R-Mobile APE6)
+		- "renesas,sysc-r8a7740" (R-Mobile A1)
+		- "renesas,sysc-sh73a0" (SH-Mobile AG5)
+- reg: Two address start and address range blocks for the device:
+         - The first block refers to the normally accessible registers,
+         - the second block refers to the registers protected by the HPB
+	   semaphore.
+
+Optional nodes:
+- pm-domains: This node contains a hierarchy of PM domain nodes, which should
+  match the Power Area Hierarchy in the Power Domain Specifications section of
+  the device's datasheet.
+
+
+== PM Domain Nodes ==
+
+Each of the PM domain nodes represents a PM domain, as documented by the
+generic PM domain bindings in
+Documentation/devicetree/bindings/power/power_domain.txt.
+
+The nodes should be named by the real power area names, and thus their names
+should be unique.
+
+Required properties:
+  - #power-domain-cells: Must be 0.
+
+Optional properties:
+- reg: If the PM domain is not always-on, this property must contain the bit
+       index number for the corresponding power area in the various Power
+       Control and Status Registers. The parent's node must contain the
+       following two properties:
+	 - #address-cells: Must be 1,
+	 - #size-cells: Must be 0.
+       If the PM domain is always-on, this property must be omitted.
+
+
+Example:
+
+This shows a subset of the r8a7740 PM domain hierarchy, containing the
+C5 "always-on" domain, 2 of its subdomains (A4S and A4SU), and the A3SP domain,
+which is a subdomain of A4S.
+
+	sysc: system-controller@e6180000 {
+		compatible = "renesas,sysc-r8a7740", "renesas,sysc-rmobile";
+		reg = <0xe6180000 0x8000>, <0xe6188000 0x8000>;
+
+		pm-domains {
+			pd_c5: c5 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				#power-domain-cells = <0>;
+
+				pd_a4s: a4s@10 {
+					reg = <10>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#power-domain-cells = <0>;
+
+					pd_a3sp: a3sp@11 {
+						reg = <11>;
+						#power-domain-cells = <0>;
+					};
+				};
+
+				pd_a4su: a4su@20 {
+					reg = <20>;
+					#power-domain-cells = <0>;
+				};
+			};
+		};
+	};
+
+
+== PM Domain Consumers ==
+
+Hardware blocks belonging to a PM domain should contain a "power-domains"
+property that is a phandle pointing to the corresponding PM domain node.
+
+Example:
+
+	tpu: pwm@e6600000 {
+		compatible = "renesas,tpu-r8a7740", "renesas,tpu";
+		reg = <0xe6600000 0x100>;
+		clocks = <&mstp3_clks R8A7740_CLK_TPU0>;
+		power-domains = <&pd_a3sp>;
+		#pwm-cells = <3>;
+	};
diff --git a/Documentation/devicetree/bindings/power/reset/keystone-reset.txt b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt
new file mode 100644
index 000000000..c82f12e2d
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/keystone-reset.txt
@@ -0,0 +1,67 @@
+* Device tree bindings for Texas Instruments keystone reset
+
+This node is intended to allow SoC reset in case of software reset
+of selected watchdogs.
+
+The Keystone SoCs can contain up to 4 watchdog timers to reset
+SoC. Each watchdog timer event input is connected to the Reset Mux
+block. The Reset Mux block can be configured to cause reset or not.
+
+Additionally soft or hard reset can be configured.
+
+Required properties:
+
+- compatible:		ti,keystone-reset
+
+- ti,syscon-pll:	phandle/offset pair. The phandle to syscon used to
+			access pll controller registers and the offset to use
+			reset control registers.
+
+- ti,syscon-dev:	phandle/offset pair. The phandle to syscon used to
+			access device state control registers and the offset
+			in order to use mux block registers for all watchdogs.
+
+Optional properties:
+
+- ti,soft-reset:	Boolean option indicating soft reset.
+			By default hard reset is used.
+
+- ti,wdt-list:		WDT list that can cause SoC reset. It's not related
+			to WDT driver, it's just needed to enable a SoC related
+			reset that's triggered by one of WDTs. The list is
+			in format: <0>, <2>; It can be in random order and
+			begins from 0 to 3, as keystone can contain up to 4 SoC
+			reset watchdogs and can be in random order.
+
+Example 1:
+Setup keystone reset so that in case software reset or
+WDT0 is triggered it issues hard reset for SoC.
+
+pllctrl: pll-controller@02310000 {
+	compatible = "ti,keystone-pllctrl", "syscon";
+	reg = <0x02310000 0x200>;
+};
+
+devctrl: device-state-control@02620000 {
+	compatible = "ti,keystone-devctrl", "syscon";
+	reg = <0x02620000 0x1000>;
+};
+
+rstctrl: reset-controller {
+	compatible = "ti,keystone-reset";
+	ti,syscon-pll = <&pllctrl 0xe4>;
+	ti,syscon-dev = <&devctrl 0x328>;
+	ti,wdt-list = <0>;
+};
+
+Example 2:
+Setup keystone reset so that in case of software reset or
+WDT0 or WDT2 is triggered it issues soft reset for SoC.
+
+rstctrl: reset-controller {
+	compatible = "ti,keystone-reset";
+	ti,syscon-pll = <&pllctrl 0xe4>;
+	ti,syscon-dev = <&devctrl 0x328>;
+	ti,wdt-list = <0>, <2>;
+	ti,soft-reset;
+};
diff --git a/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt
new file mode 100644
index 000000000..cd2d7f58a
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/ltc2952-poweroff.txt
@@ -0,0 +1,29 @@
+Binding for the LTC2952 PowerPath controller
+
+This chip is used to externally trigger a system shut down. Once the trigger has
+been sent, the chip's watchdog has to be reset to gracefully shut down.
+A full powerdown can be triggered via the kill signal.
+
+Required properties:
+
+- compatible:		Must contain: "lltc,ltc2952"
+- watchdog-gpios:	phandle + gpio-specifier for the GPIO connected to the
+			chip's watchdog line
+- kill-gpios:		phandle + gpio-specifier for the GPIO connected to the
+			chip's kill line
+
+Optional properties:
+- trigger-gpios:	phandle + gpio-specifier for the GPIO connected to the
+			chip's trigger line. If this property is not set, the
+			trigger function is ignored and the chip is kept alive
+			until an explicit kill signal is received
+
+Example:
+
+ltc2952 {
+	compatible = "lltc,ltc2952";
+
+	trigger-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+	watchdog-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	kill-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+};
diff --git a/Documentation/devicetree/bindings/power/reset/st-reset.txt b/Documentation/devicetree/bindings/power/reset/st-reset.txt
new file mode 100644
index 000000000..809af54f0
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/st-reset.txt
@@ -0,0 +1,11 @@
+*Device-Tree bindings for ST SW reset functionality
+
+Required properties:
+- compatible: should be "st,<chip>-restart".
+- st,syscfg: should be a phandle of the syscfg node.
+
+Example node:
+	restart {
+		compatible = "st,stih416-restart";
+		st,syscfg = <&syscfg_sbc>;
+	};
diff --git a/Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt b/Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt
new file mode 100644
index 000000000..1e2546f8b
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt
@@ -0,0 +1,23 @@
+Generic SYSCON mapped register poweroff driver
+
+This is a generic poweroff driver using syscon to map the poweroff register.
+The poweroff is generally performed with a write to the poweroff register
+defined by the register map pointed by syscon reference plus the offset
+with the mask defined in the poweroff node.
+
+Required properties:
+- compatible: should contain "syscon-poweroff"
+- regmap: this is phandle to the register map node
+- offset: offset in the register map for the poweroff register (in bytes)
+- mask: the poweroff value written to the poweroff register (32 bit access)
+
+Default will be little endian mode, 32 bit access only.
+
+Examples:
+
+	poweroff {
+	   compatible = "syscon-poweroff";
+	   regmap = <&regmapnode>;
+	   offset = <0x0>;
+	   mask = <0x7a>;
+	};
diff --git a/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt b/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt
new file mode 100644
index 000000000..11906316b
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/syscon-reboot.txt
@@ -0,0 +1,23 @@
+Generic SYSCON mapped register reset driver
+
+This is a generic reset driver using syscon to map the reset register.
+The reset is generally performed with a write to the reset register
+defined by the register map pointed by syscon reference plus the offset
+with the mask defined in the reboot node.
+
+Required properties:
+- compatible: should contain "syscon-reboot"
+- regmap: this is phandle to the register map node
+- offset: offset in the register map for the reboot register (in bytes)
+- mask: the reset value written to the reboot register (32 bit access)
+
+Default will be little endian mode, 32 bit access only.
+
+Examples:
+
+	reboot {
+	   compatible = "syscon-reboot";
+	   regmap = <&regmapnode>;
+	   offset = <0x0>;
+	   mask = <0x1>;
+	};
diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt
new file mode 100644
index 000000000..8b70db103
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt
@@ -0,0 +1,83 @@
+Rockchip SRAM for IO Voltage Domains:
+-------------------------------------
+
+IO domain voltages on some Rockchip SoCs are variable but need to be
+kept in sync between the regulators and the SoC using a special
+register.
+
+A specific example using rk3288:
+- If the regulator hooked up to a pin like SDMMC0_VDD is 3.3V then
+  bit 7 of GRF_IO_VSEL needs to be 0.  If the regulator hooked up to
+  that same pin is 1.8V then bit 7 of GRF_IO_VSEL needs to be 1.
+
+Said another way, this driver simply handles keeping bits in the SoC's
+general register file (GRF) in sync with the actual value of a voltage
+hooked up to the pins.
+
+Note that this driver specifically doesn't include:
+- any logic for deciding what voltage we should set regulators to
+- any logic for deciding whether regulators (or internal SoC blocks)
+  should have power or not have power
+
+If there were some other software that had the smarts of making
+decisions about regulators, it would work in conjunction with this
+driver.  When that other software adjusted a regulator's voltage then
+this driver would handle telling the SoC about it.  A good example is
+vqmmc for SD.  In that case the dw_mmc driver simply is told about a
+regulator.  It changes the regulator between 3.3V and 1.8V at the
+right time.  This driver notices the change and makes sure that the
+SoC is on the same page.
+
+
+Required properties:
+- compatible: should be one of:
+  - "rockchip,rk3188-io-voltage-domain" for rk3188
+  - "rockchip,rk3288-io-voltage-domain" for rk3288
+- rockchip,grf: phandle to the syscon managing the "general register files"
+
+
+You specify supplies using the standard regulator bindings by including
+a phandle the relevant regulator.  All specified supplies must be able
+to report their voltage.  The IO Voltage Domain for any non-specified
+supplies will be not be touched.
+
+Possible supplies for rk3188:
+- ap0-supply:    The supply connected to AP0_VCC.
+- ap1-supply:    The supply connected to AP1_VCC.
+- cif-supply:    The supply connected to CIF_VCC.
+- flash-supply:  The supply connected to FLASH_VCC.
+- lcdc0-supply:  The supply connected to LCD0_VCC.
+- lcdc1-supply:  The supply connected to LCD1_VCC.
+- vccio0-supply: The supply connected to VCCIO0.
+- vccio1-supply: The supply connected to VCCIO1.
+                 Sometimes also labeled VCCIO1 and VCCIO2.
+
+Possible supplies for rk3288:
+- audio-supply:  The supply connected to APIO4_VDD.
+- bb-supply:     The supply connected to APIO5_VDD.
+- dvp-supply:    The supply connected to DVPIO_VDD.
+- flash0-supply: The supply connected to FLASH0_VDD.  Typically for eMMC
+- flash1-supply: The supply connected to FLASH1_VDD.  Also known as SDIO1.
+- gpio30-supply: The supply connected to APIO1_VDD.
+- gpio1830       The supply connected to APIO2_VDD.
+- lcdc-supply:   The supply connected to LCDC_VDD.
+- sdcard-supply: The supply connected to SDMMC0_VDD.
+- wifi-supply:   The supply connected to APIO3_VDD.  Also known as SDIO0.
+
+
+Example:
+
+	io-domains {
+		compatible = "rockchip,rk3288-io-voltage-domain";
+		rockchip,grf = <&grf>;
+
+		audio-supply = <&vcc18_codec>;
+		bb-supply = <&vcc33_io>;
+		dvp-supply = <&vcc_18>;
+		flash0-supply = <&vcc18_flashio>;
+		gpio1830-supply = <&vcc33_io>;
+		gpio30-supply = <&vcc33_pmuio>;
+		lcdc-supply = <&vcc33_lcd>;
+		sdcard-supply = <&vccio_sd>;
+		wifi-supply = <&vcc18_wl>;
+	};
diff --git a/Documentation/devicetree/bindings/power/rx51-battery.txt b/Documentation/devicetree/bindings/power/rx51-battery.txt
new file mode 100644
index 000000000..90438453d
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/rx51-battery.txt
@@ -0,0 +1,25 @@
+Binding for Nokia N900 battery
+
+The Nokia N900 battery status can be read via the TWL4030's A/D converter.
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "nokia,n900-battery"
+- io-channels: Should contain IIO channel specifiers
+               for each element in io-channel-names.
+- io-channel-names: Should contain the following values:
+ * "temp" - The ADC channel for temperature reading
+ * "bsi"  - The ADC channel for battery size identification
+ * "vbat" - The ADC channel to measure the battery voltage
+
+Example from Nokia N900:
+
+battery: n900-battery {
+	compatible = "nokia,n900-battery";
+	io-channels = <&twl4030_madc 0>,
+		      <&twl4030_madc 4>,
+		      <&twl4030_madc 12>;
+	io-channel-names = "temp",
+			   "bsi",
+			   "vbat";
+};
diff --git a/Documentation/devicetree/bindings/power/twl-charger.txt b/Documentation/devicetree/bindings/power/twl-charger.txt
new file mode 100644
index 000000000..d5c706216
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/twl-charger.txt
@@ -0,0 +1,20 @@
+TWL BCI (Battery Charger Interface)
+
+Required properties:
+- compatible:
+  - "ti,twl4030-bci"
+- interrupts: two interrupt lines from the TWL SIH (secondary
+  interrupt handler) - interrupts 9 and 2.
+
+Optional properties:
+- ti,bb-uvolt: microvolts for charging the backup battery.
+- ti,bb-uamp: microamps for charging the backup battery.
+
+Examples:
+
+bci {
+   compatible = "ti,twl4030-bci";
+   interrupts = <9>, <2>;
+   ti,bb-uvolt = <3200000>;
+   ti,bb-uamp = <150>;
+};