Linux-libre 4.8.2-gnupck-4.8.2-gnu

6 files changed, 131 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/power/max8903-charger.txt b/Documentation/devicetree/bindings/power/max8903-charger.txt
new file mode 100644
index 000000000..f0f4e12b0
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/max8903-charger.txt
@@ -0,0 +1,25 @@
+Maxim Semiconductor MAX8903 Battery Charger bindings
+
+Required properties:
+- compatible: "maxim,max8903" for MAX8903 Battery Charger
+- dok-gpios: Valid DC power has been detected (active low, input), optional if uok-gpios is provided
+- uok-gpios: Valid USB power has been detected (active low, input), optional if dok-gpios is provided
+
+Optional properties:
+- cen-gpios: Charge enable pin (active low, output)
+- chg-gpios: Charger status pin (active low, input)
+- flt-gpios: Fault pin (active low, output)
+- dcm-gpios: Current limit mode setting (DC=1 or USB=0, output)
+- usus-gpios: USB suspend pin (active high, output)
+
+
+Example:
+
+	max8903-charger {
+		compatible = "maxim,max8903";
+		dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+		chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
+		cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+		status = "okay";
+	};
diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.txt b/Documentation/devicetree/bindings/power/renesas,apmu.txt
new file mode 100644
index 000000000..84404c9ed
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/renesas,apmu.txt
@@ -0,0 +1,31 @@
+DT bindings for the Renesas Advanced Power Management Unit
+
+Renesas R-Car line of SoCs utilize one or more APMU hardware units
+for CPU core power domain control including SMP boot and CPU Hotplug.
+
+Required properties:
+
+- compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback.
+	      Examples with soctypes are:
+		- "renesas,r8a7790-apmu" (R-Car H2)
+		- "renesas,r8a7791-apmu" (R-Car M2-W)
+		- "renesas,r8a7792-apmu" (R-Car V2H)
+		- "renesas,r8a7793-apmu" (R-Car M2-N)
+		- "renesas,r8a7794-apmu" (R-Car E2)
+
+- reg: Base address and length of the I/O registers used by the APMU.
+
+- cpus: This node contains a list of CPU cores, which should match the order
+  of CPU cores used by the WUPCR and PSTR registers in the Advanced Power
+  Management Unit section of the device's datasheet.
+
+
+Example:
+
+This shows the r8a7791 APMU that can control CPU0 and CPU1.
+
+	apmu@e6152000 {
+		compatible = "renesas,r8a7791-apmu", "renesas,apmu";
+		reg = <0 0xe6152000 0 0x188>;
+		cpus = <&cpu0 &cpu1>;
+	};
diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
index b74e4d478..0725fb37a 100644
--- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
+++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
@@ -14,6 +14,7 @@ Required properties:
       - "renesas,r8a7793-sysc" (R-Car M2-N)
       - "renesas,r8a7794-sysc" (R-Car E2)
       - "renesas,r8a7795-sysc" (R-Car H3)
+      - "renesas,r8a7796-sysc" (R-Car M3-W)
   - reg: Address start and address range for the device.
   - #power-domain-cells: Must be 1.
 
diff --git a/Documentation/devicetree/bindings/power/reset/brcm,bcm21664-resetmgr.txt b/Documentation/devicetree/bindings/power/reset/brcm,bcm21664-resetmgr.txt
new file mode 100644
index 000000000..93f31ca1e
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/brcm,bcm21664-resetmgr.txt
@@ -0,0 +1,14 @@
+Broadcom Kona Family Reset Manager
+----------------------------------
+
+The reset manager is used on the Broadcom BCM21664 SoC.
+
+Required properties:
+  - compatible: brcm,bcm21664-resetmgr
+  - reg: memory address & range
+
+Example:
+	brcm,resetmgr@35001f00 {
+		compatible = "brcm,bcm21664-resetmgr";
+		reg = <0x35001f00 0x24>;
+	};
diff --git a/Documentation/devicetree/bindings/power/reset/reboot-mode.txt b/Documentation/devicetree/bindings/power/reset/reboot-mode.txt
new file mode 100644
index 000000000..de34f27d5
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/reboot-mode.txt
@@ -0,0 +1,25 @@
+Generic reboot mode core map driver
+
+This driver get reboot mode arguments and call the write
+interface to store the magic value in special register
+or ram. Then the bootloader can read it and take different
+action according to the argument stored.
+
+All mode properties are vendor specific, it is a indication to tell
+the bootloader what to do when the system reboots, and should be named
+as mode-xxx = <magic> (xxx is mode name, magic should be a none-zero value).
+
+For example modes common on Android platform:
+- mode-normal: Normal reboot mode, system reboot with command "reboot".
+- mode-recovery: Android Recovery mode, it is a mode to format the device or update a new image.
+- mode-bootloader: Android fastboot mode, it's a mode to re-flash partitions on the Android based device.
+- mode-loader: A bootloader mode, it's a mode used to download image on Rockchip platform,
+	       usually used in development.
+
+Example:
+	reboot-mode {
+		mode-normal = <BOOT_NORMAL>;
+		mode-recovery = <BOOT_RECOVERY>;
+		mode-bootloader = <BOOT_FASTBOOT>;
+		mode-loader = <BOOT_BL_DOWNLOAD>;
+	}
diff --git a/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt b/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt
new file mode 100644
index 000000000..f7ce1d8af
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/reset/syscon-reboot-mode.txt
@@ -0,0 +1,35 @@
+SYSCON reboot mode driver
+
+This driver gets reboot mode magic value form reboot-mode driver
+and stores it in a SYSCON mapped register. Then the bootloader
+can read it and take different action according to the magic
+value stored.
+
+This DT node should be represented as a sub-node of a "syscon", "simple-mfd"
+node.
+
+Required properties:
+- compatible: should be "syscon-reboot-mode"
+- offset: offset in the register map for the storage register (in bytes)
+
+Optional property:
+- mask: bits mask of the bits in the register to store the reboot mode magic value,
+  default set to 0xffffffff if missing.
+
+The rest of the properties should follow the generic reboot-mode description
+found in reboot-mode.txt
+
+Example:
+	pmu: pmu@20004000 {
+		compatible = "rockchip,rk3066-pmu", "syscon", "simple-mfd";
+		reg = <0x20004000 0x100>;
+
+		reboot-mode {
+			compatible = "syscon-reboot-mode";
+			offset = <0x40>;
+			mode-normal = <BOOT_NORMAL>;
+			mode-recovery = <BOOT_RECOVERY>;
+			mode-bootloader = <BOOT_FASTBOOT>;
+			mode-loader = <BOOT_BL_DOWNLOAD>;
+		};
+	};