Initial import

28 files changed, 806 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt
new file mode 100644
index 000000000..cfda0d57d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/atmel-hlcdc-pwm.txt
@@ -0,0 +1,29 @@
+Device-Tree bindings for Atmel's HLCDC (High-end LCD Controller) PWM driver
+
+The Atmel HLCDC PWM is subdevice of the HLCDC MFD device.
+See ../mfd/atmel-hlcdc.txt for more details.
+
+Required properties:
+ - compatible: value should be one of the following:
+   "atmel,hlcdc-pwm"
+ - pinctr-names: the pin control state names. Should contain "default".
+ - pinctrl-0: should contain the pinctrl states described by pinctrl
+   default.
+ - #pwm-cells: should be set to 3. This PWM chip use the default 3 cells
+   bindings defined in pwm.txt in this directory.
+
+Example:
+
+	hlcdc: hlcdc@f0030000 {
+		compatible = "atmel,sama5d3-hlcdc";
+		reg = <0xf0030000 0x2000>;
+		clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+		clock-names = "periph_clk","sys_clk", "slow_clk";
+
+		hlcdc_pwm: hlcdc-pwm {
+			compatible = "atmel,hlcdc-pwm";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_lcd_pwm>;
+			#pwm-cells = <3>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt
new file mode 100644
index 000000000..02331b904
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt
@@ -0,0 +1,33 @@
+Atmel PWM controller
+
+Required properties:
+  - compatible: should be one of:
+    - "atmel,at91sam9rl-pwm"
+    - "atmel,sama5d3-pwm"
+  - reg: physical base address and length of the controller's registers
+  - #pwm-cells: Should be 3. See pwm.txt in this directory for a
+    description of the cells format.
+
+Example:
+
+	pwm0: pwm@f8034000 {
+		compatible = "atmel,at91sam9rl-pwm";
+		reg = <0xf8034000 0x400>;
+		#pwm-cells = <3>;
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+
+		d1 {
+			label = "d1";
+			pwms = <&pwm0 3 5000 0>
+			max-brightness = <255>;
+		};
+
+		d2 {
+			label = "d2";
+			pwms = <&pwm0 1 5000 1>
+			max-brightness = <255>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
new file mode 100644
index 000000000..8031148bc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt
@@ -0,0 +1,16 @@
+Atmel TCB PWM controller
+
+Required properties:
+- compatible: should be "atmel,tcb-pwm"
+- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+  the cells format. The only third cell flag supported by this binding is
+  PWM_POLARITY_INVERTED.
+- tc-block: The Timer Counter block to use as a PWM chip.
+
+Example:
+
+pwm {
+	compatible = "atmel,tcb-pwm";
+	#pwm-cells = <3>;
+	tc-block = <1>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt
new file mode 100644
index 000000000..8eae9fe78
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/brcm,kona-pwm.txt
@@ -0,0 +1,21 @@
+Broadcom Kona PWM controller device tree bindings
+
+This controller has 6 channels.
+
+Required Properties :
+- compatible: should contain "brcm,kona-pwm"
+- reg: physical base address and length of the controller's registers
+- clocks: phandle + clock specifier pair for the external clock
+- #pwm-cells: Should be 3. See pwm.txt in this directory for a
+  description of the cells format.
+
+Refer to clocks/clock-bindings.txt for generic clock consumer properties.
+
+Example:
+
+pwm: pwm@3e01a000 {
+	compatible = "brcm,bcm11351-pwm", "brcm,kona-pwm";
+	reg = <0x3e01a000 0xc4>;
+	clocks = <&pwm_clk>;
+	#pwm-cells = <3>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt
new file mode 100644
index 000000000..a183db48f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt
@@ -0,0 +1,16 @@
+* Cirris Logic CLPS711X PWM controller
+
+Required properties:
+- compatible: Shall contain "cirrus,clps711x-pwm".
+- reg: Physical base address and length of the controller's registers.
+- clocks: phandle + clock specifier pair of the PWM reference clock.
+- #pwm-cells: Should be 1. The cell specifies the index of the channel.
+
+Example:
+	pwm: pwm@80000400 {
+		compatible = "cirrus,ep7312-pwm",
+			     "cirrus,clps711x-pwm";
+		reg = <0x80000400 0x4>;
+		clocks = <&clks 8>;
+		#pwm-cells = <1>;
+	};
diff --git a/Documentation/devicetree/bindings/pwm/img-pwm.txt b/Documentation/devicetree/bindings/pwm/img-pwm.txt
new file mode 100644
index 000000000..fade5f26f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/img-pwm.txt
@@ -0,0 +1,24 @@
+*Imagination Technologies PWM DAC driver
+
+Required properties:
+  - compatible: Should be "img,pistachio-pwm"
+  - reg: Should contain physical base address and length of pwm registers.
+  - clocks: Must contain an entry for each entry in clock-names.
+	See ../clock/clock-bindings.txt for details.
+  - clock-names: Must include the following entries.
+    - pwm: PWM operating clock.
+    - sys: PWM system interface clock.
+  - #pwm-cells: Should be 2. See pwm.txt in this directory for the
+	description of the cells format.
+  - img,cr-periph: Must contain a phandle to the peripheral control
+	syscon node which contains PWM control registers.
+
+Example:
+	pwm: pwm@18101300 {
+		compatible = "img,pistachio-pwm";
+		reg = <0x18101300 0x100>;
+		clocks = <&pwm_clk>, <&system_clk>;
+		clock-names = "pwm", "sys";
+		#pwm-cells = <2>;
+		img,cr-periph = <&cr_periph>;
+	};
diff --git a/Documentation/devicetree/bindings/pwm/imx-pwm.txt b/Documentation/devicetree/bindings/pwm/imx-pwm.txt
new file mode 100644
index 000000000..e00c2e9f4
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/imx-pwm.txt
@@ -0,0 +1,27 @@
+Freescale i.MX PWM controller
+
+Required properties:
+- compatible : should be "fsl,<soc>-pwm" and one of the following
+   compatible strings:
+  - "fsl,imx1-pwm" for PWM compatible with the one integrated on i.MX1
+  - "fsl,imx27-pwm" for PWM compatible with the one integrated on i.MX27
+- reg: physical base address and length of the controller's registers
+- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+  the cells format.
+- clocks : Clock specifiers for both ipg and per clocks.
+- clock-names : Clock names should include both "ipg" and "per"
+See the clock consumer binding,
+	Documentation/devicetree/bindings/clock/clock-bindings.txt
+- interrupts: The interrupt for the pwm controller
+
+Example:
+
+pwm1: pwm@53fb4000 {
+	#pwm-cells = <2>;
+	compatible = "fsl,imx53-pwm", "fsl,imx27-pwm";
+	reg = <0x53fb4000 0x4000>;
+	clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>,
+		 <&clks IMX5_CLK_PWM1_HF_GATE>;
+	clock-names = "ipg", "per";
+	interrupts = <61>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt b/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt
new file mode 100644
index 000000000..cfe1db3bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/lpc32xx-pwm.txt
@@ -0,0 +1,12 @@
+LPC32XX PWM controller
+
+Required properties:
+- compatible: should be "nxp,lpc3220-pwm"
+- reg: physical base address and length of the controller's registers
+
+Examples:
+
+pwm@0x4005C000 {
+	compatible = "nxp,lpc3220-pwm";
+	reg = <0x4005C000 0x8>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/mxs-pwm.txt b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt
new file mode 100644
index 000000000..96cdde5f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/mxs-pwm.txt
@@ -0,0 +1,17 @@
+Freescale MXS PWM controller
+
+Required properties:
+- compatible: should be "fsl,imx23-pwm"
+- reg: physical base address and length of the controller's registers
+- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+  the cells format.
+- fsl,pwm-number: the number of PWM devices
+
+Example:
+
+pwm: pwm@80064000 {
+	compatible = "fsl,imx28-pwm", "fsl,imx23-pwm";
+	reg = <0x80064000 0x2000>;
+	#pwm-cells = <2>;
+	fsl,pwm-number = <8>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt
new file mode 100644
index 000000000..c52f03b50
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt
@@ -0,0 +1,27 @@
+Tegra SoC PWFM controller
+
+Required properties:
+- compatible: For Tegra20, must contain "nvidia,tegra20-pwm".  For Tegra30,
+  must contain "nvidia,tegra30-pwm".  Otherwise, must contain
+  "nvidia,<chip>-pwm", plus one of the above, where <chip> is tegra114,
+  tegra124, tegra132, or tegra210.
+- reg: physical base address and length of the controller's registers
+- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+  the cells format.
+- clocks: Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - pwm
+
+Example:
+
+	pwm: pwm@7000a000 {
+		compatible = "nvidia,tegra20-pwm";
+		reg = <0x7000a000 0x100>;
+		#pwm-cells = <2>;
+		clocks = <&tegra_car 17>;
+		resets = <&tegra_car 17>;
+		reset-names = "pwm";
+	};
diff --git a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt
new file mode 100644
index 000000000..f84ec9d29
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt
@@ -0,0 +1,27 @@
+NXP PCA9685 16-channel 12-bit PWM LED controller
+================================================
+
+Required properties:
+  - compatible: "nxp,pca9685-pwm"
+  - #pwm-cells: Should be 2. See pwm.txt in this directory for a description of
+    the cells format.
+    The index 16 is the ALLCALL channel, that sets all PWM channels at the same
+    time.
+
+Optional properties:
+  - invert (bool): boolean to enable inverted logic
+  - open-drain (bool): boolean to configure outputs with open-drain structure;
+		       if omitted use totem-pole structure
+
+Example:
+
+For LEDs that are directly connected to the PCA, the following setting is
+applicable:
+
+pca: pca@41 {
+	compatible = "nxp,pca9685-pwm";
+	#pwm-cells = <2>;
+	reg = <0x41>;
+	invert;
+	open-drain;
+};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt
new file mode 100644
index 000000000..fb6fb31bc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-bcm2835.txt
@@ -0,0 +1,30 @@
+BCM2835 PWM controller (Raspberry Pi controller)
+
+Required properties:
+- compatible: should be "brcm,bcm2835-pwm"
+- reg: physical base address and length of the controller's registers
+- clock: This clock defines the base clock frequency of the PWM hardware
+  system, the period and the duty_cycle of the PWM signal is a multiple of
+  the base period.
+- #pwm-cells: Should be 2. See pwm.txt in this directory for a description of
+  the cells format.
+
+Examples:
+
+pwm@2020c000 {
+	compatible = "brcm,bcm2835-pwm";
+	reg = <0x2020c000 0x28>;
+	clocks = <&clk_pwm>;
+	#pwm-cells = <2>;
+};
+
+clocks {
+	....
+		clk_pwm: pwm {
+			compatible = "fixed-clock";
+			reg = <3>;
+			#clock-cells = <0>;
+			clock-frequency = <9200000>;
+		};
+	....
+};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt
new file mode 100644
index 000000000..3899d6a55
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-fsl-ftm.txt
@@ -0,0 +1,52 @@
+Freescale FlexTimer Module (FTM) PWM controller
+
+The same FTM PWM device can have a different endianness on different SoCs. The
+device tree provides a property to describing this so that an operating system
+device driver can handle all variants of the device. Refer to the table below
+for the endianness of the FTM PWM block as integrated into the existing SoCs:
+
+	SoC     | FTM-PWM endianness
+	--------+-------------------
+	Vybrid  | LE
+	LS1     | BE
+	LS2     | LE
+
+Please see ../regmap/regmap.txt for more detail about how to specify endian
+modes in device tree.
+
+
+Required properties:
+- compatible: Should be "fsl,vf610-ftm-pwm".
+- reg: Physical base address and length of the controller's registers
+- #pwm-cells: Should be 3. See pwm.txt in this directory for a description of
+  the cells format.
+- clock-names: Should include the following module clock source entries:
+    "ftm_sys" (module clock, also can be used as counter clock),
+    "ftm_ext" (external counter clock),
+    "ftm_fix" (fixed counter clock),
+    "ftm_cnt_clk_en" (external and fixed counter clock enable/disable).
+- clocks: Must contain a phandle and clock specifier for each entry in
+  clock-names, please see clock/clock-bindings.txt for details of the property
+  values.
+- pinctrl-names: Must contain a "default" entry.
+- pinctrl-NNN: One property must exist for each entry in pinctrl-names.
+  See pinctrl/pinctrl-bindings.txt for details of the property values.
+- big-endian: Boolean property, required if the FTM PWM registers use a big-
+  endian rather than little-endian layout.
+
+Example:
+
+pwm0: pwm@40038000 {
+		compatible = "fsl,vf610-ftm-pwm";
+		reg = <0x40038000 0x1000>;
+		#pwm-cells = <3>;
+		clock-names = "ftm_sys", "ftm_ext",
+				"ftm_fix", "ftm_cnt_clk_en";
+		clocks = <&clks VF610_CLK_FTM0>,
+			<&clks VF610_CLK_FTM0_EXT_SEL>,
+			<&clks VF610_CLK_FTM0_FIX_SEL>,
+			<&clks VF610_CLK_FTM0_EXT_FIX_EN>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pwm0_1>;
+		big-endian;
+};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt
new file mode 100644
index 000000000..7bd9d3b12
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-lp3943.txt
@@ -0,0 +1,58 @@
+TI/National Semiconductor LP3943 PWM controller
+
+Required properties:
+  - compatible: "ti,lp3943-pwm"
+  - #pwm-cells: Should be 2. See pwm.txt in this directory for a
+                description of the cells format.
+                Note that this hardware limits the period length to the
+                range 6250~1600000.
+  - ti,pwm0 or ti,pwm1: Output pin number(s) for PWM channel 0 or 1.
+    0 = output 0
+    1 = output 1
+    .
+    .
+    15 = output 15
+
+Example:
+PWM 0 is for RGB LED brightness control
+PWM 1 is for brightness control of LP8557 backlight device
+
+&i2c3 {
+	lp3943@60 {
+		compatible = "ti,lp3943";
+		reg = <0x60>;
+
+		/*
+		 * PWM 0 : output 8, 9 and 10
+		 * PWM 1 : output 15
+		 */
+		pwm3943: pwm {
+			compatible = "ti,lp3943-pwm";
+			#pwm-cells = <2>;
+			ti,pwm0 = <8 9 10>;
+			ti,pwm1 = <15>;
+		};
+	};
+
+};
+
+/* LEDs control with PWM 0 of LP3943 */
+pwmleds {
+	compatible = "pwm-leds";
+	rgb {
+		label = "indi::rgb";
+		pwms = <&pwm3943 0 10000>;
+		max-brightness = <255>;
+	};
+};
+
+&i2c4 {
+	/* Backlight control with PWM 1 of LP3943 */
+	backlight@2c {
+		compatible = "ti,lp8557";
+		reg = <0x2c>;
+
+		pwms = <&pwm3943 1 10000>;
+		pwm-names = "lp8557";
+	};
+};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt
new file mode 100644
index 000000000..b8be3d09e
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-rockchip.txt
@@ -0,0 +1,20 @@
+Rockchip PWM controller
+
+Required properties:
+ - compatible: should be "rockchip,<name>-pwm"
+   "rockchip,rk2928-pwm": found on RK29XX,RK3066 and RK3188 SoCs
+   "rockchip,rk3288-pwm": found on RK3288 SoC
+   "rockchip,vop-pwm": found integrated in VOP on RK3288 SoC
+ - reg: physical base address and length of the controller's registers
+ - clocks: phandle and clock specifier of the PWM reference clock
+ - #pwm-cells: must be 2 (rk2928) or 3 (rk3288). See pwm.txt in this directory
+   for a description of the cell format.
+
+Example:
+
+	pwm0: pwm@20030000 {
+		compatible = "rockchip,rk2928-pwm";
+		reg = <0x20030000 0x10>;
+		clocks = <&cru PCLK_PWM01>;
+		#pwm-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-samsung.txt b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt
new file mode 100644
index 000000000..5538de9c2
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-samsung.txt
@@ -0,0 +1,51 @@
+* Samsung PWM timers
+
+Samsung SoCs contain PWM timer blocks which can be used for system clock source
+and clock event timers, as well as to drive SoC outputs with PWM signal. Each
+PWM timer block provides 5 PWM channels (not all of them can drive physical
+outputs - see SoC and board manual).
+
+Be aware that the clocksource driver supports only uniprocessor systems.
+
+Required properties:
+- compatible : should be one of following:
+    samsung,s3c2410-pwm - for 16-bit timers present on S3C24xx SoCs
+    samsung,s3c6400-pwm - for 32-bit timers present on S3C64xx SoCs
+    samsung,s5p6440-pwm - for 32-bit timers present on S5P64x0 SoCs
+    samsung,s5pc100-pwm - for 32-bit timers present on S5PC100, S5PV210,
+			  Exynos4210 rev0 SoCs
+    samsung,exynos4210-pwm - for 32-bit timers present on Exynos4210,
+                          Exynos4x12, Exynos5250 and Exynos5420 SoCs
+- reg: base address and size of register area
+- interrupts: list of timer interrupts (one interrupt per timer, starting at
+  timer 0)
+- clock-names: should contain all following required clock names:
+    - "timers" - PWM base clock used to generate PWM signals,
+  and any subset of following optional clock names:
+    - "pwm-tclk0" - first external PWM clock source,
+    - "pwm-tclk1" - second external PWM clock source.
+  Note that not all IP variants allow using all external clock sources.
+  Refer to SoC documentation to learn which clock source configurations
+  are available.
+- clocks: should contain clock specifiers of all clocks, which input names
+  have been specified in clock-names property, in same order.
+- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+  the cells format. The only third cell flag supported by this binding is
+  PWM_POLARITY_INVERTED.
+
+Optional properties:
+- samsung,pwm-outputs: list of PWM channels used as PWM outputs on particular
+    platform - an array of up to 5 elements being indices of PWM channels
+    (from 0 to 4), the order does not matter.
+
+Example:
+	pwm@7f006000 {
+		compatible = "samsung,s3c6400-pwm";
+		reg = <0x7f006000 0x1000>;
+		interrupt-parent = <&vic0>;
+		interrupts = <23>, <24>, <25>, <27>, <28>;
+		clocks = <&clock 67>;
+		clock-names = "timers";
+		samsung,pwm-outputs = <0>, <1>;
+		#pwm-cells = <3>;
+	}
diff --git a/Documentation/devicetree/bindings/pwm/pwm-st.txt b/Documentation/devicetree/bindings/pwm/pwm-st.txt
new file mode 100644
index 000000000..84d2fb807
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-st.txt
@@ -0,0 +1,41 @@
+STMicroelectronics PWM driver bindings
+--------------------------------------
+
+Required parameters:
+- compatible :		"st,pwm"
+- #pwm-cells : 		Number of cells used to specify a PWM. First cell
+			specifies the per-chip index of the PWM to use and the
+			second cell is the period in nanoseconds - fixed to 2
+			for STiH41x.
+- reg :			Physical base address and length of the controller's
+			registers.
+- pinctrl-names: 	Set to "default".
+- pinctrl-0: 		List of phandles pointing to pin configuration nodes
+			for PWM module.
+			For Pinctrl properties, please refer to [1].
+- clock-names: 		Set to "pwm".
+- clocks: 		phandle of the clock used by the PWM module.
+			For Clk properties, please refer to [2].
+
+Optional properties:
+- st,pwm-num-chan:	Number of available channels. If not passed, the driver
+			will consider single channel by default.
+
+[1] Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+[2] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Example:
+
+pwm1: pwm@fe510000 {
+	compatible = "st,pwm";
+	reg = <0xfe510000 0x68>;
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1_chan0_default
+		     &pinctrl_pwm1_chan1_default
+		     &pinctrl_pwm1_chan2_default
+		     &pinctrl_pwm1_chan3_default>;
+	clocks = <&clk_sysin>;
+	clock-names = "pwm";
+	st,pwm-num-chan = <4>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt
new file mode 100644
index 000000000..ae0273e19
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-sun4i.txt
@@ -0,0 +1,20 @@
+Allwinner sun4i and sun7i SoC PWM controller
+
+Required properties:
+  - compatible: should be one of:
+    - "allwinner,sun4i-a10-pwm"
+    - "allwinner,sun7i-a20-pwm"
+  - reg: physical base address and length of the controller's registers
+  - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+    the cells format.
+  - clocks: From common clock binding, handle to the parent clock.
+
+Example:
+
+	pwm: pwm@01c20e00 {
+		compatible = "allwinner,sun7i-a20-pwm";
+		reg = <0x01c20e00 0xc>;
+		clocks = <&osc24M>;
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
new file mode 100644
index 000000000..fb81179dc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiecap.txt
@@ -0,0 +1,29 @@
+TI SOC ECAP based APWM controller
+
+Required properties:
+- compatible: Must be "ti,<soc>-ecap".
+  for am33xx - compatible = "ti,am33xx-ecap";
+  for da850  - compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+  the cells format. The PWM channel index ranges from 0 to 4. The only third
+  cell flag supported by this binding is PWM_POLARITY_INVERTED.
+- reg: physical base address and size of the registers map.
+
+Optional properties:
+- ti,hwmods: Name of the hwmod associated to the ECAP:
+  "ecap<x>", <x> being the 0-based instance number from the HW spec
+
+Example:
+
+ecap0: ecap@0 { /* ECAP on am33xx */
+	compatible = "ti,am33xx-ecap";
+	#pwm-cells = <3>;
+	reg = <0x48300100 0x80>;
+	ti,hwmods = "ecap0";
+};
+
+ecap0: ecap@0 { /* ECAP on da850 */
+	compatible = "ti,da850-ecap", "ti,am33xx-ecap";
+	#pwm-cells = <3>;
+	reg = <0x306000 0x80>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
new file mode 100644
index 000000000..9c100b2c5
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-tiehrpwm.txt
@@ -0,0 +1,29 @@
+TI SOC EHRPWM based PWM controller
+
+Required properties:
+- compatible: Must be "ti,<soc>-ehrpwm".
+  for am33xx - compatible = "ti,am33xx-ehrpwm";
+  for da850  - compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+  the cells format. The only third cell flag supported by this binding is
+  PWM_POLARITY_INVERTED.
+- reg: physical base address and size of the registers map.
+
+Optional properties:
+- ti,hwmods: Name of the hwmod associated to the EHRPWM:
+  "ehrpwm<x>", <x> being the 0-based instance number from the HW spec
+
+Example:
+
+ehrpwm0: ehrpwm@0 { /* EHRPWM on am33xx */
+	compatible = "ti,am33xx-ehrpwm";
+	#pwm-cells = <3>;
+	reg = <0x48300200 0x100>;
+	ti,hwmods = "ehrpwm0";
+};
+
+ehrpwm0: ehrpwm@0 { /* EHRPWM on da850 */
+	compatible = "ti,da850-ehrpwm", "ti,am33xx-ehrpwm";
+	#pwm-cells = <3>;
+	reg = <0x300000 0x2000>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt
new file mode 100644
index 000000000..f7eae77f8
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm-tipwmss.txt
@@ -0,0 +1,31 @@
+TI SOC based PWM Subsystem
+
+Required properties:
+- compatible: Must be "ti,am33xx-pwmss";
+- reg: physical base address and size of the registers map.
+- address-cells: Specify the number of u32 entries needed in child nodes.
+		  Should set to 1.
+- size-cells: specify number of u32 entries needed to specify child nodes size
+		in reg property. Should set to 1.
+- ranges: describes the address mapping of a memory-mapped bus. Should set to
+	   physical address map of child's base address, physical address within
+	   parent's address  space and length of the address map. For am33xx,
+	   3 set of child register maps present, ECAP register space, EQEP
+	   register space, EHRPWM register space.
+
+Also child nodes should also populated under PWMSS DT node.
+
+Example:
+pwmss0: pwmss@48300000 {
+	compatible = "ti,am33xx-pwmss";
+	reg = <0x48300000 0x10>;
+	ti,hwmods = "epwmss0";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	status = "disabled";
+	ranges = <0x48300100 0x48300100 0x80   /* ECAP */
+		  0x48300180 0x48300180 0x80   /* EQEP */
+		  0x48300200 0x48300200 0x80>; /* EHRPWM */
+
+	/* child nodes go here */
+};
diff --git a/Documentation/devicetree/bindings/pwm/pwm.txt b/Documentation/devicetree/bindings/pwm/pwm.txt
new file mode 100644
index 000000000..8556263b8
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pwm.txt
@@ -0,0 +1,69 @@
+Specifying PWM information for devices
+======================================
+
+1) PWM user nodes
+-----------------
+
+PWM users should specify a list of PWM devices that they want to use
+with a property containing a 'pwm-list':
+
+	pwm-list ::= <single-pwm> [pwm-list]
+	single-pwm ::= <pwm-phandle> <pwm-specifier>
+	pwm-phandle : phandle to PWM controller node
+	pwm-specifier : array of #pwm-cells specifying the given PWM
+			(controller specific)
+
+PWM properties should be named "pwms". The exact meaning of each pwms
+property must be documented in the device tree binding for each device.
+An optional property "pwm-names" may contain a list of strings to label
+each of the PWM devices listed in the "pwms" property. If no "pwm-names"
+property is given, the name of the user node will be used as fallback.
+
+Drivers for devices that use more than a single PWM device can use the
+"pwm-names" property to map the name of the PWM device requested by the
+pwm_get() call to an index into the list given by the "pwms" property.
+
+The following example could be used to describe a PWM-based backlight
+device:
+
+	pwm: pwm {
+		#pwm-cells = <2>;
+	};
+
+	[...]
+
+	bl: backlight {
+		pwms = <&pwm 0 5000000>;
+		pwm-names = "backlight";
+	};
+
+Note that in the example above, specifying the "pwm-names" is redundant
+because the name "backlight" would be used as fallback anyway.
+
+pwm-specifier typically encodes the chip-relative PWM number and the PWM
+period in nanoseconds.
+
+Optionally, the pwm-specifier can encode a number of flags (defined in
+<dt-bindings/pwm/pwm.h>) in a third cell:
+- PWM_POLARITY_INVERTED: invert the PWM signal polarity
+
+Example with optional PWM specifier for inverse polarity
+
+	bl: backlight {
+		pwms = <&pwm 0 5000000 PWM_POLARITY_INVERTED>;
+		pwm-names = "backlight";
+	};
+
+2) PWM controller nodes
+-----------------------
+
+PWM controller nodes must specify the number of cells used for the
+specifier using the '#pwm-cells' property.
+
+An example PWM controller might look like this:
+
+	pwm: pwm@7000a000 {
+		compatible = "nvidia,tegra20-pwm";
+		reg = <0x7000a000 0x100>;
+		#pwm-cells = <2>;
+	};
diff --git a/Documentation/devicetree/bindings/pwm/pxa-pwm.txt b/Documentation/devicetree/bindings/pwm/pxa-pwm.txt
new file mode 100644
index 000000000..5ae9f1e3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/pxa-pwm.txt
@@ -0,0 +1,30 @@
+Marvell PWM controller
+
+Required properties:
+- compatible: should be one or more of:
+  - "marvell,pxa250-pwm"
+  - "marvell,pxa270-pwm"
+  - "marvell,pxa168-pwm"
+  - "marvell,pxa910-pwm"
+- reg: Physical base address and length of the registers used by the PWM channel
+  Note that one device instance must be created for each PWM that is used, so the
+  length covers only the register window for one PWM output, not that of the
+  entire PWM controller.  Currently length is 0x10 for all supported devices.
+- #pwm-cells: Should be 1.  This cell is used to specify the period in
+  nanoseconds.
+
+Example PWM device node:
+
+pwm0: pwm@40b00000 {
+	compatible = "marvell,pxa250-pwm";
+	reg = <0x40b00000 0x10>;
+	#pwm-cells = <1>;
+};
+
+Example PWM client node:
+
+backlight {
+	compatible = "pwm-backlight";
+	pwms = <&pwm0 5000000>;
+	...
+}
diff --git a/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
new file mode 100644
index 000000000..b067e84a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/renesas,tpu-pwm.txt
@@ -0,0 +1,28 @@
+* Renesas R-Car Timer Pulse Unit PWM Controller
+
+Required Properties:
+
+  - compatible: should be one of the following.
+    - "renesas,tpu-r8a73a4": for R8A77A4 (R-Mobile APE6) compatible PWM controller.
+    - "renesas,tpu-r8a7740": for R8A7740 (R-Mobile A1) compatible PWM controller.
+    - "renesas,tpu-r8a7790": for R8A7790 (R-Car H2) compatible PWM controller.
+    - "renesas,tpu-sh7372": for SH7372 (SH-Mobile AP4) compatible PWM controller.
+    - "renesas,tpu": for generic R-Car TPU PWM controller.
+
+  - reg: Base address and length of each memory resource used by the PWM
+    controller hardware module.
+
+  - #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+    the cells format. The only third cell flag supported by this binding is
+    PWM_POLARITY_INVERTED.
+
+Please refer to pwm.txt in this directory for details of the common PWM bindings
+used by client devices.
+
+Example: R8A7740 (R-Car A1) TPU controller node
+
+	tpu: pwm@e6600000 {
+		compatible = "renesas,tpu-r8a7740", "renesas,tpu";
+		reg = <0xe6600000 0x100>;
+		#pwm-cells = <3>;
+	};
diff --git a/Documentation/devicetree/bindings/pwm/spear-pwm.txt b/Documentation/devicetree/bindings/pwm/spear-pwm.txt
new file mode 100644
index 000000000..b486de2c3
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/spear-pwm.txt
@@ -0,0 +1,17 @@
+== ST SPEAr SoC PWM controller ==
+
+Required properties:
+- compatible: should be one of:
+  - "st,spear320-pwm"
+  - "st,spear1340-pwm"
+- reg: physical base address and length of the controller's registers
+- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+  the cells format.
+
+Example:
+
+        pwm: pwm@a8000000 {
+            compatible ="st,spear320-pwm";
+            reg = <0xa8000000 0x1000>;
+            #pwm-cells = <2>;
+        };
diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt
new file mode 100644
index 000000000..4e32bee11
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwm.txt
@@ -0,0 +1,17 @@
+Texas Instruments TWL series PWM drivers
+
+Supported PWMs:
+On TWL4030 series: PWM1 and PWM2
+On TWL6030 series: PWM0 and PWM1
+
+Required properties:
+- compatible: "ti,twl4030-pwm" or "ti,twl6030-pwm"
+- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+  the cells format.
+
+Example:
+
+twl_pwm: pwm {
+	compatible = "ti,twl6030-pwm";
+	#pwm-cells = <2>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt
new file mode 100644
index 000000000..9f4b46090
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/ti,twl-pwmled.txt
@@ -0,0 +1,17 @@
+Texas Instruments TWL series PWM drivers connected to LED terminals
+
+Supported PWMs:
+On TWL4030 series: PWMA and PWMB (connected to LEDA and LEDB terminals)
+On TWL6030 series: LED PWM (mainly used as charging indicator LED)
+
+Required properties:
+- compatible: "ti,twl4030-pwmled" or "ti,twl6030-pwmled"
+- #pwm-cells: should be 2. See pwm.txt in this directory for a description of
+  the cells format.
+
+Example:
+
+twl_pwmled: pwmled {
+	compatible = "ti,twl6030-pwmled";
+	#pwm-cells = <2>;
+};
diff --git a/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt
new file mode 100644
index 000000000..a76390e6d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pwm/vt8500-pwm.txt
@@ -0,0 +1,18 @@
+VIA/Wondermedia VT8500/WM8xxx series SoC PWM controller
+
+Required properties:
+- compatible: should be "via,vt8500-pwm"
+- reg: physical base address and length of the controller's registers
+- #pwm-cells: should be 3. See pwm.txt in this directory for a description of
+  the cells format. The only third cell flag supported by this binding is
+  PWM_POLARITY_INVERTED.
+- clocks: phandle to the PWM source clock
+
+Example:
+
+pwm1: pwm@d8220000 {
+	#pwm-cells = <3>;
+	compatible = "via,vt8500-pwm";
+	reg = <0xd8220000 0x1000>;
+	clocks = <&clkpwm>;
+};