Initial import

1 files changed, 82 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/sound/samsung-i2s.txt b/Documentation/devicetree/bindings/sound/samsung-i2s.txt
new file mode 100644
index 000000000..09e0e1859
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/samsung-i2s.txt
@@ -0,0 +1,82 @@
+* Samsung I2S controller
+
+Required SoC Specific Properties:
+
+- compatible : should be one of the following.
+   - samsung,s3c6410-i2s: for 8/16/24bit stereo I2S.
+   - samsung,s5pv210-i2s: for 8/16/24bit multichannel(5.1) I2S with
+     secondary fifo, s/w reset control and internal mux for root clk src.
+   - samsung,exynos5420-i2s: for 8/16/24bit multichannel(5.1) I2S for
+     playback, sterio channel capture, secondary fifo using internal
+     or external dma, s/w reset control, internal mux for root clk src
+     and 7.1 channel TDM support for playback. TDM (Time division multiplexing)
+     is to allow transfer of multiple channel audio data on single data line.
+   - samsung,exynos7-i2s: with all the available features of exynos5 i2s,
+     exynos7 I2S has 7.1 channel TDM support for capture, secondary fifo
+     with only external dma and more no.of root clk sampling frequencies.
+   - samsung,exynos7-i2s1: I2S1 on previous samsung platforms supports
+     stereo channels. exynos7 i2s1 upgraded to 5.1 multichannel with
+     slightly modified bit offsets.
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- dmas: list of DMA controller phandle and DMA request line ordered pairs.
+- dma-names: identifier string for each DMA request line in the dmas property.
+  These strings correspond 1:1 with the ordered pairs in dmas.
+- clocks: Handle to iis clock and RCLK source clk.
+- clock-names:
+  i2s0 uses some base clks from CMU and some are from audio subsystem internal
+  clock controller. The clock names for i2s0 should be "iis", "i2s_opclk0" and
+  "i2s_opclk1" as shown in the example below.
+  i2s1 and i2s2 uses clocks from CMU. The clock names for i2s1 and i2s2 should
+  be "iis" and "i2s_opclk0".
+  "iis" is the i2s bus clock and i2s_opclk0, i2s_opclk1 are sources of the root
+  clk. i2s0 has internal mux to select the source of root clk and i2s1 and i2s2
+  doesn't have any such mux.
+- #clock-cells: should be 1, this property must be present if the I2S device
+  is a clock provider in terms of the common clock bindings, described in
+  ../clock/clock-bindings.txt.
+- clock-output-names: from the common clock bindings, names of the CDCLK
+  I2S output clocks, suggested values are "i2s_cdclk0", "i2s_cdclk1",
+  "i2s_cdclk3" for the I2S0, I2S1, I2S2 devices recpectively.
+
+There are following clocks available at the I2S device nodes:
+ CLK_I2S_CDCLK    - the CDCLK (CODECLKO) gate clock,
+ CLK_I2S_RCLK_PSR - the RCLK prescaler divider clock (corresponding to the
+		    IISPSR register),
+ CLK_I2S_RCLK_SRC - the RCLKSRC mux clock (corresponding to RCLKSRC bit in
+		    IISMOD register).
+
+Refer to the SoC datasheet for availability of the above clocks.
+The CLK_I2S_RCLK_PSR and CLK_I2S_RCLK_SRC clocks are usually only available
+in the IIS Multi Audio Interface (I2S0).
+Note: Old DTs may not have the #clock-cells, clock-output-names properties
+and then not use the I2S node as a clock supplier.
+
+Optional SoC Specific Properties:
+
+- samsung,idma-addr: Internal DMA register base address of the audio
+  sub system(used in secondary sound source).
+- pinctrl-0: Should specify pin control groups used for this controller.
+- pinctrl-names: Should contain only one value - "default".
+
+
+Example:
+
+i2s0: i2s@03830000 {
+	compatible = "samsung,s5pv210-i2s";
+	reg = <0x03830000 0x100>;
+	dmas = <&pdma0 10
+		&pdma0 9
+		&pdma0 8>;
+	dma-names = "tx", "rx", "tx-sec";
+	clocks = <&clock_audss EXYNOS_I2S_BUS>,
+		<&clock_audss EXYNOS_I2S_BUS>,
+		<&clock_audss EXYNOS_SCLK_I2S>;
+	clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
+	#clock-cells;
+	clock-output-names = "i2s_cdclk0";
+	samsung,idma-addr = <0x03000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s0_bus>;
+};