diff options
| author | André Fabian Silva Delgado <emulatorman@parabola.nu> | 2015-08-05 17:04:01 -0300 |
|---|---|---|
| committer | André Fabian Silva Delgado <emulatorman@parabola.nu> | 2015-08-05 17:04:01 -0300 |
| commit | 57f0f512b273f60d52568b8c6b77e17f5636edc0 (patch) | |
| tree | 5e910f0e82173f4ef4f51111366a3f1299037a7b /Documentation/devicetree/bindings/spi | |
Initial import
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
37 files changed, 1549 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt b/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt new file mode 100644 index 000000000..f11f295c8 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt @@ -0,0 +1,22 @@ +Broadcom BCM2835 SPI0 controller + +The BCM2835 contains two forms of SPI master controller, one known simply as +SPI0, and the other known as the "Universal SPI Master"; part of the +auxiliary block. This binding applies to the SPI0 controller. + +Required properties: +- compatible: Should be "brcm,bcm2835-spi". +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks: The clock feeding the SPI controller. + +Example: + +spi@20204000 { + compatible = "brcm,bcm2835-spi"; + reg = <0x7e204000 0x1000>; + interrupts = <2 22>; + clocks = <&clk_spi>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/efm32-spi.txt b/Documentation/devicetree/bindings/spi/efm32-spi.txt new file mode 100644 index 000000000..750e29aff --- /dev/null +++ b/Documentation/devicetree/bindings/spi/efm32-spi.txt @@ -0,0 +1,41 @@ +* Energy Micro EFM32 SPI + +Required properties: +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- compatible: should be "energymicro,efm32-spi" +- reg: Offset and length of the register set for the controller +- interrupts: pair specifying rx and tx irq +- clocks: phandle to the spi clock +- cs-gpios: see spi-bus.txt + +Recommended properties : +- energymicro,location: Value to write to the ROUTE register's LOCATION + bitfield to configure the pinmux for the device, see + datasheet for values. + If this property is not provided, keeping what is + already configured in the hardware, so its either the + reset default 0 or whatever the bootloader did. + +Example: + +spi1: spi@0x4000c400 { /* USART1 */ + #address-cells = <1>; + #size-cells = <0>; + compatible = "energymicro,efm32-spi"; + reg = <0x4000c400 0x400>; + interrupts = <15 16>; + clocks = <&cmu 20>; + cs-gpios = <&gpio 51 1>; // D3 + energymicro,location = <1>; + status = "ok"; + + ks8851@0 { + compatible = "ks8851"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&boardfpga>; + interrupts = <4>; + status = "ok"; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt new file mode 100644 index 000000000..523341a0e --- /dev/null +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -0,0 +1,37 @@ +* Freescale (Enhanced) Configurable Serial Peripheral Interface + (CSPI/eCSPI) for i.MX + +Required properties: +- compatible : + - "fsl,imx1-cspi" for SPI compatible with the one integrated on i.MX1 + - "fsl,imx21-cspi" for SPI compatible with the one integrated on i.MX21 + - "fsl,imx27-cspi" for SPI compatible with the one integrated on i.MX27 + - "fsl,imx31-cspi" for SPI compatible with the one integrated on i.MX31 + - "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35 + - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 +- reg : Offset and length of the register set for the device +- interrupts : Should contain CSPI/eCSPI interrupt +- fsl,spi-num-chipselects : Contains the number of the chipselect +- cs-gpios : Specifies the gpio pins to be used for chipselects. +- clocks : Clock specifiers for both ipg and per clocks. +- clock-names : Clock names should include both "ipg" and "per" +See the clock consumer binding, + Documentation/devicetree/bindings/clock/clock-bindings.txt +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: DMA request names should include "tx" and "rx" if present. + +Example: + +ecspi@70010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx51-ecspi"; + reg = <0x70010000 0x4000>; + interrupts = <36>; + fsl,spi-num-chipselects = <2>; + cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */ + <&gpio3 25 0>; /* GPIO3_25 */ + dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/spi/fsl-spi.txt b/Documentation/devicetree/bindings/spi/fsl-spi.txt new file mode 100644 index 000000000..a23313720 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/fsl-spi.txt @@ -0,0 +1,60 @@ +* SPI (Serial Peripheral Interface) + +Required properties: +- cell-index : QE SPI subblock index. + 0: QE subblock SPI1 + 1: QE subblock SPI2 +- compatible : should be "fsl,spi" or "aeroflexgaisler,spictrl". +- mode : the SPI operation mode, it can be "cpu" or "cpu-qe". +- reg : Offset and length of the register set for the device +- interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. +- interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. +- clock-frequency : input clock frequency to non FSL_SOC cores + +Optional properties: +- gpios : specifies the gpio pins to be used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child nodes. + If unspecified, a single SPI device without a chip select can be used. + +Example: + spi@4c0 { + cell-index = <0>; + compatible = "fsl,spi"; + reg = <4c0 40>; + interrupts = <82 0>; + interrupt-parent = <700>; + mode = "cpu"; + gpios = <&gpio 18 1 // device reg=<0> + &gpio 19 1>; // device reg=<1> + }; + + +* eSPI (Enhanced Serial Peripheral Interface) + +Required properties: +- compatible : should be "fsl,mpc8536-espi". +- reg : Offset and length of the register set for the device. +- interrupts : should contain eSPI interrupt, the device has one interrupt. +- fsl,espi-num-chipselects : the number of the chipselect signals. + +Optional properties: +- fsl,csbef: chip select assertion time in bits before frame starts +- fsl,csaft: chip select negation time in bits after frame ends + +Example: + spi@110000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc8536-espi"; + reg = <0x110000 0x1000>; + interrupts = <53 0x2>; + interrupt-parent = <&mpic>; + fsl,espi-num-chipselects = <4>; + fsl,csbef = <1>; + fsl,csaft = <1>; + }; diff --git a/Documentation/devicetree/bindings/spi/mxs-spi.txt b/Documentation/devicetree/bindings/spi/mxs-spi.txt new file mode 100644 index 000000000..3499b7329 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/mxs-spi.txt @@ -0,0 +1,26 @@ +* Freescale MX233/MX28 SSP/SPI + +Required properties: +- compatible: Should be "fsl,<soc>-spi", where soc is "imx23" or "imx28" +- reg: Offset and length of the register set for the device +- interrupts: Should contain SSP ERROR interrupt +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and SSP DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: Must be "rx-tx". + +Optional properties: +- clock-frequency : Input clock frequency to the SPI block in Hz. + Default is 160000000 Hz. + +Example: + +ssp0: ssp@80010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-spi"; + reg = <0x80010000 0x2000>; + interrupts = <96>; + dmas = <&dma_apbh 0>; + dma-names = "rx-tx"; +}; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt new file mode 100644 index 000000000..b785976fe --- /dev/null +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra114-spi.txt @@ -0,0 +1,42 @@ +NVIDIA Tegra114 SPI controller. + +Required properties: +- compatible : For Tegra114, must contain "nvidia,tegra114-spi". + Otherwise, must contain '"nvidia,<chip>-spi", "nvidia,tegra114-spi"' where + <chip> is tegra124, tegra132, or tegra210. +- reg: Should contain SPI registers location and length. +- interrupts: Should contain SPI interrupts. +- clock-names : Must include the following entries: + - spi +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - spi +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt +Example: + +spi@7000d600 { + compatible = "nvidia,tegra114-spi"; + reg = <0x7000d600 0x200>; + interrupts = <0 82 0x04>; + spi-max-frequency = <25000000>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&tegra_car 44>; + clock-names = "spi"; + resets = <&tegra_car 44>; + reset-names = "spi"; + dmas = <&apbdma 16>, <&apbdma 16>; + dma-names = "rx", "tx"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt new file mode 100644 index 000000000..bdf08e6de --- /dev/null +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-sflash.txt @@ -0,0 +1,38 @@ +NVIDIA Tegra20 SFLASH controller. + +Required properties: +- compatible : should be "nvidia,tegra20-sflash". +- reg: Should contain SFLASH registers location and length. +- interrupts: Should contain SFLASH interrupts. +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - spi +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +spi@7000c380 { + compatible = "nvidia,tegra20-sflash"; + reg = <0x7000c380 0x80>; + interrupts = <0 39 0x04>; + spi-max-frequency = <25000000>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&tegra_car 43>; + resets = <&tegra_car 43>; + reset-names = "spi"; + dmas = <&apbdma 11>, <&apbdma 11>; + dma-names = "rx", "tx"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt new file mode 100644 index 000000000..5db9144a3 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/nvidia,tegra20-slink.txt @@ -0,0 +1,38 @@ +NVIDIA Tegra20/Tegra30 SLINK controller. + +Required properties: +- compatible : should be "nvidia,tegra20-slink", "nvidia,tegra30-slink". +- reg: Should contain SLINK registers location and length. +- interrupts: Should contain SLINK interrupts. +- clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - spi +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +spi@7000d600 { + compatible = "nvidia,tegra20-slink"; + reg = <0x7000d600 0x200>; + interrupts = <0 82 0x04>; + spi-max-frequency = <25000000>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&tegra_car 44>; + resets = <&tegra_car 44>; + reset-names = "spi"; + dmas = <&apbdma 16>, <&apbdma 16>; + dma-names = "rx", "tx"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/spi/omap-spi.txt b/Documentation/devicetree/bindings/spi/omap-spi.txt new file mode 100644 index 000000000..2ba5f9c02 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/omap-spi.txt @@ -0,0 +1,47 @@ +OMAP2+ McSPI device + +Required properties: +- compatible : + - "ti,omap2-mcspi" for OMAP2 & OMAP3. + - "ti,omap4-mcspi" for OMAP4+. +- ti,spi-num-cs : Number of chipselect supported by the instance. +- ti,hwmods: Name of the hwmod associated to the McSPI +- ti,pindir-d0-out-d1-in: Select the D0 pin as output and D1 as + input. The default is D0 as input and + D1 as output. + +Optional properties: +- dmas: List of DMA specifiers with the controller specific format + as described in the generic DMA client binding. A tx and rx + specifier is required for each chip select. +- dma-names: List of DMA request names. These strings correspond + 1:1 with the DMA specifiers listed in dmas. The string naming + is to be "rxN" and "txN" for RX and TX requests, + respectively, where N equals the chip select number. + +Examples: + +[hwmod populated DMA resources] + +mcspi1: mcspi@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,omap4-mcspi"; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <4>; +}; + +[generic DMA request binding] + +mcspi1: mcspi@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,omap4-mcspi"; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <2>; + dmas = <&edma 42 + &edma 43 + &edma 44 + &edma 45>; + dma-names = "tx0", "rx0", "tx1", "rx1"; +}; diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt new file mode 100644 index 000000000..5c090771c --- /dev/null +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt @@ -0,0 +1,103 @@ +Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI) + +The QUP core is an AHB slave that provides a common data path (an output FIFO +and an input FIFO) for serial peripheral interface (SPI) mini-core. + +SPI in master mode supports up to 50MHz, up to four chip selects, programmable +data path from 4 bits to 32 bits and numerous protocol variants. + +Required properties: +- compatible: Should contain: + "qcom,spi-qup-v1.1.1" for 8660, 8960 and 8064. + "qcom,spi-qup-v2.1.1" for 8974 and later + "qcom,spi-qup-v2.2.1" for 8974 v2 and later. + +- reg: Should contain base register location and length +- interrupts: Interrupt number used by this controller + +- clocks: Should contain the core clock and the AHB clock. +- clock-names: Should be "core" for the core clock and "iface" for the + AHB clock. + +- #address-cells: Number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: Should be zero. + +Optional properties: +- spi-max-frequency: Specifies maximum SPI clock frequency, + Units - Hz. Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt +- num-cs: total number of chipselects +- cs-gpios: should specify GPIOs used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child + nodes. If unspecified, a single SPI device without a chip + select can be used. + +- dmas: Two DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt +- dma-names: Names for the dma channels, if present. There must be at + least one channel named "tx" for transmit and named "rx" for + receive. + +SPI slave nodes must be children of the SPI master node and can contain +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + spi_8: spi@f9964000 { /* BLSP2 QUP2 */ + + compatible = "qcom,spi-qup-v2"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xf9964000 0x1000>; + interrupts = <0 102 0>; + spi-max-frequency = <19200000>; + + clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + + dmas = <&blsp1_bam 13>, <&blsp1_bam 12>; + dma-names = "rx", "tx"; + + pinctrl-names = "default"; + pinctrl-0 = <&spi8_default>; + + device@0 { + compatible = "arm,pl022-dummy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <19200000>; + spi-cpol; + }; + + device@1 { + compatible = "arm,pl022-dummy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <1>; /* Chip select 1 */ + spi-max-frequency = <9600000>; + spi-cpha; + }; + + device@2 { + compatible = "arm,pl022-dummy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <2>; /* Chip select 2 */ + spi-max-frequency = <19200000>; + spi-cpol; + spi-cpha; + }; + + device@3 { + compatible = "arm,pl022-dummy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <3>; /* Chip select 3 */ + spi-max-frequency = <19200000>; + spi-cpol; + spi-cpha; + spi-cs-high; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/sh-hspi.txt b/Documentation/devicetree/bindings/spi/sh-hspi.txt new file mode 100644 index 000000000..319bad4af --- /dev/null +++ b/Documentation/devicetree/bindings/spi/sh-hspi.txt @@ -0,0 +1,29 @@ +Renesas HSPI. + +Required properties: +- compatible : "renesas,hspi-<soctype>", "renesas,hspi" as fallback. + Examples with soctypes are: + - "renesas,hspi-r8a7778" (R-Car M1) + - "renesas,hspi-r8a7779" (R-Car H1) +- reg : Offset and length of the register set for the device +- interrupt-parent : The phandle for the interrupt controller that + services interrupts for this device +- interrupts : Interrupt specifier +- #address-cells : Must be <1> +- #size-cells : Must be <0> + +Pinctrl properties might be needed, too. See +Documentation/devicetree/bindings/pinctrl/renesas,*. + +Example: + + hspi0: spi@fffc7000 { + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; + reg = <0xfffc7000 0x18>; + interrupt-parent = <&gic>; + interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt new file mode 100644 index 000000000..4c388bb2f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -0,0 +1,71 @@ +Renesas MSIOF spi controller + +Required properties: +- compatible : "renesas,msiof-<soctype>" for SoCs, + "renesas,sh-msiof" for SuperH, or + "renesas,sh-mobile-msiof" for SH Mobile series. + Examples with soctypes are: + "renesas,msiof-r8a7790" (R-Car H2) + "renesas,msiof-r8a7791" (R-Car M2-W) + "renesas,msiof-r8a7792" (R-Car V2H) + "renesas,msiof-r8a7793" (R-Car M2-N) + "renesas,msiof-r8a7794" (R-Car E2) +- reg : A list of offsets and lengths of the register sets for + the device. + If only one register set is present, it is to be used + by both the CPU and the DMA engine. + If two register sets are present, the first is to be + used by the CPU, and the second is to be used by the + DMA engine. +- interrupt-parent : The phandle for the interrupt controller that + services interrupts for this device +- interrupts : Interrupt specifier +- #address-cells : Must be <1> +- #size-cells : Must be <0> + +Optional properties: +- clocks : Must contain a reference to the functional clock. +- num-cs : Total number of chip-selects (default is 1) +- dmas : Must contain a list of two references to DMA + specifiers, one for transmission, and one for + reception. +- dma-names : Must contain a list of two DMA names, "tx" and "rx". +- renesas,dtdl : delay sync signal (setup) in transmit mode. + Must contain one of the following values: + 0 (no bit delay) + 50 (0.5-clock-cycle delay) + 100 (1-clock-cycle delay) + 150 (1.5-clock-cycle delay) + 200 (2-clock-cycle delay) + +- renesas,syncdl : delay sync signal (hold) in transmit mode. + Must contain one of the following values: + 0 (no bit delay) + 50 (0.5-clock-cycle delay) + 100 (1-clock-cycle delay) + 150 (1.5-clock-cycle delay) + 200 (2-clock-cycle delay) + 300 (3-clock-cycle delay) + +Optional properties, deprecated for soctype-specific bindings: +- renesas,tx-fifo-size : Overrides the default tx fifo size given in words + (default is 64) +- renesas,rx-fifo-size : Overrides the default rx fifo size given in words + (default is 64, or 256 on R-Car Gen2) + +Pinctrl properties might be needed, too. See +Documentation/devicetree/bindings/pinctrl/renesas,*. + +Example: + + msiof0: spi@e6e20000 { + compatible = "renesas,msiof-r8a7791"; + reg = <0 0xe6e20000 0 0x0064>, <0 0xe7e20000 0 0x0064>; + interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>; + dmas = <&dmac0 0x51>, <&dmac0 0x52>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt new file mode 100644 index 000000000..bd99193e8 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt @@ -0,0 +1,28 @@ +Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface. + +Required properties: +- compatible : "snps,dw-apb-ssi" +- reg : The register base for the controller. +- interrupts : One interrupt, used by the controller. +- #address-cells : <1>, as required by generic SPI binding. +- #size-cells : <0>, also as required by generic SPI binding. + +Optional properties: +- cs-gpios : Specifies the gpio pis to be used for chipselects. +- num-cs : The number of chipselects. If omitted, this will default to 4. + +Child nodes as per the generic SPI binding. + +Example: + + spi@fff00000 { + compatible = "snps,dw-apb-ssi"; + reg = <0xfff00000 0x1000>; + interrupts = <0 154 4>; + #address-cells = <1>; + #size-cells = <0>; + num-cs = <2>; + cs-gpios = <&gpio0 13 0>, + <&gpio0 14 0>; + }; + diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt new file mode 100644 index 000000000..bbaa857dd --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -0,0 +1,94 @@ +SPI (Serial Peripheral Interface) busses + +SPI busses can be described with a node for the SPI master device +and a set of child nodes for each SPI slave on the bus. For this +discussion, it is assumed that the system's SPI controller is in +SPI master mode. This binding does not describe SPI controllers +in slave mode. + +The SPI master node requires the following properties: +- #address-cells - number of cells required to define a chip select + address on the SPI bus. +- #size-cells - should be zero. +- compatible - name of SPI bus controller following generic names + recommended practice. +- cs-gpios - (optional) gpios chip select. +No other properties are required in the SPI bus node. It is assumed +that a driver for an SPI bus device will understand that it is an SPI bus. +However, the binding does not attempt to define the specific method for +assigning chip select numbers. Since SPI chip select configuration is +flexible and non-standardized, it is left out of this binding with the +assumption that board specific platform code will be used to manage +chip selects. Individual drivers can define additional properties to +support describing the chip select layout. + +Optional property: +- num-cs : total number of chipselects + +If cs-gpios is used the number of chip select will automatically increased +with max(cs-gpios > hw cs) + +So if for example the controller has 2 CS lines, and the cs-gpios +property looks like this: + +cs-gpios = <&gpio1 0 0> <0> <&gpio1 1 0> <&gpio1 2 0>; + +Then it should be configured so that num_chipselect = 4 with the +following mapping: + +cs0 : &gpio1 0 0 +cs1 : native +cs2 : &gpio1 1 0 +cs3 : &gpio1 2 0 + +SPI slave nodes must be children of the SPI master node and can +contain the following properties. +- reg - (required) chip select address of device. +- compatible - (required) name of SPI device following generic names + recommended practice +- spi-max-frequency - (required) Maximum SPI clocking speed of device in Hz +- spi-cpol - (optional) Empty property indicating device requires + inverse clock polarity (CPOL) mode +- spi-cpha - (optional) Empty property indicating device requires + shifted clock phase (CPHA) mode +- spi-cs-high - (optional) Empty property indicating device requires + chip select active high +- spi-3wire - (optional) Empty property indicating device requires + 3-wire mode. +- spi-lsb-first - (optional) Empty property indicating device requires + LSB first mode. +- spi-tx-bus-width - (optional) The bus width(number of data wires) that + used for MOSI. Defaults to 1 if not present. +- spi-rx-bus-width - (optional) The bus width(number of data wires) that + used for MISO. Defaults to 1 if not present. + +Some SPI controllers and devices support Dual and Quad SPI transfer mode. +It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD). +Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is +only 1(SINGLE), 2(DUAL) and 4(QUAD). +Dual/Quad mode is not allowed when 3-wire mode is used. + +If a gpio chipselect is used for the SPI slave the gpio number will be passed +via the SPI master node cs-gpios property. + +SPI example for an MPC5200 SPI bus: + spi@f00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + + codec@1 { + compatible = "ti,tlv320aic26"; + spi-max-frequency = <100000>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-cadence.txt b/Documentation/devicetree/bindings/spi/spi-cadence.txt new file mode 100644 index 000000000..94f09141a --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-cadence.txt @@ -0,0 +1,31 @@ +Cadence SPI controller Device Tree Bindings +------------------------------------------- + +Required properties: +- compatible : Should be "cdns,spi-r1p6" or "xlnx,zynq-spi-r1p6". +- reg : Physical base address and size of SPI registers map. +- interrupts : Property with a value describing the interrupt + number. +- interrupt-parent : Must be core interrupt controller +- clock-names : List of input clock names - "ref_clk", "pclk" + (See clock bindings for details). +- clocks : Clock phandles (see clock bindings for details). + +Optional properties: +- num-cs : Number of chip selects used. + If a decoder is used, this will be the number of + chip selects after the decoder. +- is-decoded-cs : Flag to indicate whether decoder is used or not. + +Example: + + spi@e0007000 { + compatible = "xlnx,zynq-spi-r1p6"; + clock-names = "ref_clk", "pclk"; + clocks = <&clkc 26>, <&clkc 35>; + interrupt-parent = <&intc>; + interrupts = <0 49 4>; + num-cs = <4>; + is-decoded-cs = <0>; + reg = <0xe0007000 0x1000>; + } ; diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt new file mode 100644 index 000000000..12ecfe9e3 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -0,0 +1,88 @@ +Davinci SPI controller device bindings + +Links on DM: +Keystone 2 - http://www.ti.com/lit/ug/sprugp2a/sprugp2a.pdf +dm644x - http://www.ti.com/lit/ug/sprue32a/sprue32a.pdf +OMAP-L138/da830 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf + +Required properties: +- #address-cells: number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: should be zero. +- compatible: + - "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family + - "ti,da830-spi" for SPI used similar to that on DA8xx SoC family +- reg: Offset and length of SPI controller register space +- num-cs: Number of chip selects. This includes internal as well as + GPIO chip selects. +- ti,davinci-spi-intr-line: interrupt line used to connect the SPI + IP to the interrupt controller within the SoC. Possible values + are 0 and 1. Manual says one of the two possible interrupt + lines can be tied to the interrupt controller. Set this + based on a specifc SoC configuration. +- interrupts: interrupt number mapped to CPU. +- clocks: spi clk phandle + +Optional: +- cs-gpios: gpio chip selects + For example to have 3 internal CS and 2 GPIO CS, user could define + cs-gpios = <0>, <0>, <0>, <&gpio1 30 0>, <&gpio1 31 0>; + where first three are internal CS and last two are GPIO CS. + +Optional properties for slave devices: +SPI slave nodes can contain the following properties. +Not all SPI Peripherals from Texas Instruments support this. +Please check SPI peripheral documentation for a device before using these. + +- ti,spi-wdelay : delay between transmission of words + (SPIFMTn.WDELAY, SPIDAT1.WDEL) must be specified in number of SPI module + clock periods. + + delay = WDELAY * SPI_module_clock_period + 2 * SPI_module_clock_period + +Below is timing diagram which shows functional meaning of +"ti,spi-wdelay" parameter. + + +-+ +-+ +-+ +-+ +-+ +-+ +-+ +-+ +SPI_CLK | | | | | | | | | | | | | | | | + +----------+ +-+ +-+ +-+ +-+ +---------------------------+ +-+ +-+ +- + +SPI_SOMI/SIMO+-----------------+ +----------- + +----------+ word1 +---------------------------+word2 + +-----------------+ +----------- + WDELAY + <--------------------------> + +Example of a NOR flash slave device (n25q032) connected to DaVinci +SPI controller device over the SPI bus. + +spi0:spi@20BF0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,dm6446-spi"; + reg = <0x20BF0000 0x1000>; + num-cs = <4>; + ti,davinci-spi-intr-line = <0>; + interrupts = <338>; + clocks = <&clkspi>; + + flash: n25q032@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p32"; + spi-max-frequency = <25000000>; + reg = <0>; + ti,spi-wdelay = <8>; + + partition@0 { + label = "u-boot-spl"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@1 { + label = "test"; + reg = <0x80000 0x380000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-dw.txt b/Documentation/devicetree/bindings/spi/spi-dw.txt new file mode 100644 index 000000000..7b63ed601 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-dw.txt @@ -0,0 +1,24 @@ +Synopsys DesignWare SPI master + +Required properties: +- compatible: should be "snps,designware-spi" +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- reg: address and length of the spi master registers +- interrupts: should contain one interrupt +- clocks: spi clock phandle +- num-cs: see spi-bus.txt + +Optional properties: +- cs-gpios: see spi-bus.txt + +Example: + +spi: spi@4020a000 { + compatible = "snps,designware-spi"; + interrupts = <11 1>; + reg = <0x4020a000 0x1000>; + clocks = <&pclk>; + num-cs = <2>; + cs-gpios = <&banka 0 0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt new file mode 100644 index 000000000..70af78a91 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -0,0 +1,57 @@ +ARM Freescale DSPI controller + +Required properties: +- compatible : "fsl,vf610-dspi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI controller interrupt +- clocks: from common clock binding: handle to dspi clock. +- clock-names: from common clock binding: Shall be "dspi". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must contain a "default" entry. +- spi-num-chipselects : the number of the chipselect signals. +- bus-num : the slave chip chipselect signal number. + +Optional property: +- big-endian: If present the dspi device's registers are implemented + in big endian mode, otherwise in native mode(same with CPU), for more + detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. + +Optional SPI slave node properties: +- fsl,spi-cs-sck-delay: a delay in nanoseconds between activating chip + select and the start of clock signal, at the start of a transfer. +- fsl,spi-sck-cs-delay: a delay in nanoseconds between stopping the clock + signal and deactivating chip select, at the end of a transfer. + +Example: + +dspi0@4002c000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,vf610-dspi"; + reg = <0x4002c000 0x1000>; + interrupts = <0 67 0x04>; + clocks = <&clks VF610_CLK_DSPI0>; + clock-names = "dspi"; + spi-num-chipselects = <5>; + bus-num = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dspi0_1>; + big-endian; + status = "okay"; + + sflash: at26df081a@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "atmel,at26df081a"; + spi-max-frequency = <16000000>; + spi-cpol; + spi-cpha; + reg = <0>; + linux,modalias = "m25p80"; + modal = "at26df081a"; + fsl,spi-cs-sck-delay = <100>; + fsl,spi-sck-cs-delay = <50>; + }; +}; + + diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.txt b/Documentation/devicetree/bindings/spi/spi-gpio.txt new file mode 100644 index 000000000..a95603bcf --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-gpio.txt @@ -0,0 +1,31 @@ +SPI-GPIO devicetree bindings + +Required properties: + + - compatible: should be set to "spi-gpio" + - #address-cells: should be set to <0x1> + - ranges + - gpio-sck: GPIO spec for the SCK line to use + - gpio-miso: GPIO spec for the MISO line to use + - gpio-mosi: GPIO spec for the MOSI line to use + - cs-gpios: GPIOs to use for chipselect lines. + Not needed if num-chipselects = <0>. + - num-chipselects: Number of chipselect lines. Should be <0> if a single device + with no chip select is connected. + +Example: + + spi { + compatible = "spi-gpio"; + #address-cells = <0x1>; + ranges; + + gpio-sck = <&gpio 95 0>; + gpio-miso = <&gpio 98 0>; + gpio-mosi = <&gpio 97 0>; + cs-gpios = <&gpio 125 0>; + num-chipselects = <1>; + + /* clients */ + }; + diff --git a/Documentation/devicetree/bindings/spi/spi-img-spfi.txt b/Documentation/devicetree/bindings/spi/spi-img-spfi.txt new file mode 100644 index 000000000..e02fbf18c --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-img-spfi.txt @@ -0,0 +1,38 @@ +IMG Synchronous Peripheral Flash Interface (SPFI) controller + +Required properties: +- compatible: Must be "img,spfi". +- reg: Must contain the base address and length of the SPFI registers. +- interrupts: Must contain the SPFI interrupt. +- clocks: Must contain an entry for each entry in clock-names. + See ../clock/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - spfi: SPI operating clock + - sys: SPI system interface clock +- dmas: Must contain an entry for each entry in dma-names. + See ../dma/dma.txt for details. +- dma-names: Must include the following entries: + - rx + - tx +- cs-gpios: Must specify the GPIOs used for chipselect lines. +- #address-cells: Must be 1. +- #size-cells: Must be 0. + +Optional properties: +- img,supports-quad-mode: Should be set if the interface supports quad mode + SPI transfers. + +Example: + +spi@18100f00 { + compatible = "img,spfi"; + reg = <0x18100f00 0x100>; + interrupts = <GIC_SHARED 22 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&spi_clk>, <&system_clk>; + clock-names = "spfi", "sys"; + dmas = <&mdc 9 0xffffffff 0>, <&mdc 10 0xffffffff 0>; + dma-names = "rx", "tx"; + + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt new file mode 100644 index 000000000..bb52a86f3 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-meson.txt @@ -0,0 +1,22 @@ +Amlogic Meson SPI controllers + +* SPIFC (SPI Flash Controller) + +The Meson SPIFC is a controller optimized for communication with SPI +NOR memories, without DMA support and a 64-byte unified transmit / +receive buffer. + +Required properties: + - compatible: should be "amlogic,meson6-spifc" + - reg: physical base address and length of the controller registers + - clocks: phandle of the input clock for the baud rate generator + - #address-cells: should be 1 + - #size-cells: should be 0 + + spi@c1108c80 { + compatible = "amlogic,meson6-spifc"; + reg = <0xc1108c80 0x80>; + clocks = <&clk81>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-octeon.txt b/Documentation/devicetree/bindings/spi/spi-octeon.txt new file mode 100644 index 000000000..431add192 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-octeon.txt @@ -0,0 +1,33 @@ +Cavium, Inc. OCTEON SOC SPI master controller. + +Required properties: +- compatible : "cavium,octeon-3010-spi" +- reg : The register base for the controller. +- interrupts : One interrupt, used by the controller. +- #address-cells : <1>, as required by generic SPI binding. +- #size-cells : <0>, also as required by generic SPI binding. + +Child nodes as per the generic SPI binding. + +Example: + + spi@1070000001000 { + compatible = "cavium,octeon-3010-spi"; + reg = <0x10700 0x00001000 0x0 0x100>; + interrupts = <0 58>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + compatible = "st,m95256", "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; + + pagesize = <64>; + size = <32768>; + address-width = <16>; + }; + }; + diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt new file mode 100644 index 000000000..50c3a3de6 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -0,0 +1,19 @@ +Marvell Orion SPI device + +Required properties: +- compatible : should be "marvell,orion-spi" or "marvell,armada-370-spi". +- reg : offset and length of the register set for the device +- cell-index : Which of multiple SPI controllers is this. +Optional properties: +- interrupts : Is currently not used. + +Example: + spi@10600 { + compatible = "marvell,orion-spi"; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + reg = <0x10600 0x28>; + interrupts = <23>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt new file mode 100644 index 000000000..0c491bda4 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -0,0 +1,45 @@ +* Rockchip SPI Controller + +The Rockchip SPI controller is used to interface with various devices such as flash +and display controllers using the SPI communication interface. + +Required Properties: + +- compatible: should be one of the following. + "rockchip,rk3066-spi" for rk3066. + "rockchip,rk3188-spi", "rockchip,rk3066-spi" for rk3188. + "rockchip,rk3288-spi", "rockchip,rk3066-spi" for rk3288. +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Shall be "spiclk" for the transfer-clock, and "apb_pclk" for + the peripheral clock. +- #address-cells: should be 1. +- #size-cells: should be 0. + +Optional Properties: + +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, + Documentation/devicetree/bindings/dma/dma.txt +- dma-names: DMA request names should include "tx" and "rx" if present. +- rx-sample-delay-ns: nanoseconds to delay after the SCLK edge before sampling + Rx data (may need to be fine tuned for high capacitance lines). + No delay (0) by default. + + +Example: + + spi0: spi@ff110000 { + compatible = "rockchip,rk3066-spi"; + reg = <0xff110000 0x1000>; + dmas = <&pdma1 11>, <&pdma1 12>; + dma-names = "tx", "rx"; + rx-sample-delay-ns = <10>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; + clock-names = "spiclk", "apb_pclk"; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-rspi.txt b/Documentation/devicetree/bindings/spi/spi-rspi.txt new file mode 100644 index 000000000..8f4169f63 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-rspi.txt @@ -0,0 +1,69 @@ +Device tree configuration for Renesas RSPI/QSPI driver + +Required properties: +- compatible : For Renesas Serial Peripheral Interface on legacy SH: + "renesas,rspi-<soctype>", "renesas,rspi" as fallback. + For Renesas Serial Peripheral Interface on RZ/A1H: + "renesas,rspi-<soctype>", "renesas,rspi-rz" as fallback. + For Quad Serial Peripheral Interface on R-Car Gen2: + "renesas,qspi-<soctype>", "renesas,qspi" as fallback. + Examples with soctypes are: + - "renesas,rspi-sh7757" (SH) + - "renesas,rspi-r7s72100" (RZ/A1H) + - "renesas,qspi-r8a7790" (R-Car H2) + - "renesas,qspi-r8a7791" (R-Car M2-W) + - "renesas,qspi-r8a7792" (R-Car V2H) + - "renesas,qspi-r8a7793" (R-Car M2-N) + - "renesas,qspi-r8a7794" (R-Car E2) +- reg : Address start and address range size of the device +- interrupts : A list of interrupt-specifiers, one for each entry in + interrupt-names. + If interrupt-names is not present, an interrupt specifier + for a single muxed interrupt. +- interrupt-names : A list of interrupt names. Should contain (if present): + - "error" for SPEI, + - "rx" for SPRI, + - "tx" to SPTI, + - "mux" for a single muxed interrupt. +- interrupt-parent : The phandle for the interrupt controller that + services interrupts for this device. +- num-cs : Number of chip selects. Some RSPI cores have more than 1. +- #address-cells : Must be <1> +- #size-cells : Must be <0> + +Optional properties: +- clocks : Must contain a reference to the functional clock. +- dmas : Must contain a list of two references to DMA specifiers, + one for transmission, and one for reception. +- dma-names : Must contain a list of two DMA names, "tx" and "rx". + +Pinctrl properties might be needed, too. See +Documentation/devicetree/bindings/pinctrl/renesas,*. + +Examples: + + spi0: spi@e800c800 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800c800 0x24>; + interrupts = <0 238 IRQ_TYPE_LEVEL_HIGH>, + <0 239 IRQ_TYPE_LEVEL_HIGH>, + <0 240 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + interrupt-parent = <&gic>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi: spi@e6b10000 { + compatible = "renesas,qspi-r8a7791", "renesas,qspi"; + reg = <0 0xe6b10000 0 0x2c>; + interrupt-parent = <&gic>; + interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&dmac0 0x17>, <&dmac0 0x18>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt new file mode 100644 index 000000000..6dbdeb3c3 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -0,0 +1,109 @@ +* Samsung SPI Controller + +The Samsung SPI controller is used to interface with various devices such as flash +and display controllers using the SPI communication interface. + +Required SoC Specific Properties: + +- compatible: should be one of the following. + - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms + - samsung,s3c6410-spi: for s3c6410 platforms + - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms + - samsung,exynos7-spi: for exynos7 platforms + +- reg: physical base address of the controller and length of memory mapped + region. + +- interrupts: The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. + +- dmas : Two or more DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt + +- dma-names: Names for the dma channels. There must be at least one channel + named "tx" for transmit and named "rx" for receive. + +Required Board Specific Properties: + +- #address-cells: should be 1. +- #size-cells: should be 0. + +Optional Board Specific Properties: + +- samsung,spi-src-clk: If the spi controller includes a internal clock mux to + select the clock source for the spi bus clock, this property can be used to + indicate the clock to be used for driving the spi bus clock. If not specified, + the clock number 0 is used as default. + +- num-cs: Specifies the number of chip select lines supported. If + not specified, the default number of chip select lines is set to 1. + +- cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt) + +SPI Controller specific data in SPI slave nodes: + +- The spi slave nodes should provide the following information which is required + by the spi controller. + + - samsung,spi-feedback-delay: The sampling phase shift to be applied on the + miso line (to account for any lag in the miso line). The following are the + valid values. + + - 0: No phase shift. + - 1: 90 degree phase shift sampling. + - 2: 180 degree phase shift sampling. + - 3: 270 degree phase shift sampling. + +Aliases: + +- All the SPI controller nodes should be represented in the aliases node using + the following format 'spi{n}' where n is a unique number for the alias. + + +Example: + +- SoC Specific Portion: + + spi_0: spi@12d20000 { + compatible = "samsung,exynos4210-spi"; + reg = <0x12d20000 0x100>; + interrupts = <0 66 0>; + dmas = <&pdma0 5 + &pdma0 4>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + }; + +- Board Specific Portion: + + spi_0: spi@12d20000 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&spi0_bus>; + cs-gpios = <&gpa2 5 0>; + + w25q80bw@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "w25x80"; + reg = <0>; + spi-max-frequency = <10000>; + + controller-data { + samsung,spi-feedback-delay = <0>; + }; + + partition@0 { + label = "U-Boot"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "Kernel"; + reg = <0x40000 0xc0000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-sc18is602.txt b/Documentation/devicetree/bindings/spi/spi-sc18is602.txt new file mode 100644 index 000000000..02f903327 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sc18is602.txt @@ -0,0 +1,23 @@ +NXP SC18IS602/SCIS603 + +Required properties: + - compatible : Should be one of + "nxp,sc18is602" + "nxp,sc18is602b" + "nxp,sc18is603" + - reg: I2C bus address + +Optional properties: + - clock-frequency : external oscillator clock frequency. If not + specified, the SC18IS602 default frequency (7372000) will be used. + +The clock-frequency property is relevant and needed only if the chip has an +external oscillator (SC18IS603). + +Example: + + sc18is603@28 { + compatible = "nxp,sc18is603"; + reg = <0x28>; + clock-frequency = <14744000>; + } diff --git a/Documentation/devicetree/bindings/spi/spi-sirf.txt b/Documentation/devicetree/bindings/spi/spi-sirf.txt new file mode 100644 index 000000000..4c7adb8f7 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sirf.txt @@ -0,0 +1,41 @@ +* CSR SiRFprimaII Serial Peripheral Interface + +Required properties: +- compatible : Should be "sirf,prima2-spi" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI interrupt +- resets: phandle to the reset controller asserting this device in + reset + See ../reset/reset.txt for details. +- dmas : Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names : Must include the following entries: + - rx + - tx +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + +- #address-cells: Number of cells required to define a chip select + address on the SPI bus. Should be set to 1. +- #size-cells: Should be zero. + +Optional properties: +- spi-max-frequency: Specifies maximum SPI clock frequency, + Units - Hz. Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt +- cs-gpios: should specify GPIOs used for chipselects. + +Example: + +spi0: spi@b00d0000 { + compatible = "sirf,prima2-spi"; + reg = <0xb00d0000 0x10000>; + interrupts = <15>; + dmas = <&dmac1 9>, + <&dmac1 4>; + dma-names = "rx", "tx"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clks 19>; + resets = <&rstc 26>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-st-ssc.txt b/Documentation/devicetree/bindings/spi/spi-st-ssc.txt new file mode 100644 index 000000000..fe54959ec --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-st-ssc.txt @@ -0,0 +1,40 @@ +STMicroelectronics SSC (SPI) Controller +--------------------------------------- + +Required properties: +- compatible : "st,comms-ssc4-spi" +- reg : Offset and length of the device's register set +- interrupts : The interrupt specifier +- clock-names : Must contain "ssc" +- clocks : Must contain an entry for each name in clock-names + See ../clk/* +- pinctrl-names : Uses "default", can use "sleep" if provided + See ../pinctrl/pinctrl-binding.txt + +Optional properties: +- cs-gpios : List of GPIO chip selects + See ../spi/spi-bus.txt + +Child nodes represent devices on the SPI bus + See ../spi/spi-bus.txt + +Example: + spi@9840000 { + compatible = "st,comms-ssc4-spi"; + reg = <0x9840000 0x110>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_s_c0_flexgen CLK_EXT2F_A9>; + clock-names = "ssc"; + pinctrl-0 = <&pinctrl_spi0_default>; + pinctrl-names = "default"; + cs-gpios = <&pio17 5 0>; + #address-cells = <1>; + #size-cells = <0>; + + st95hf@0{ + compatible = "st,st95hf"; + reg = <0>; + spi-max-frequency = <1000000>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-sun4i.txt b/Documentation/devicetree/bindings/spi/spi-sun4i.txt new file mode 100644 index 000000000..de827f5a3 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sun4i.txt @@ -0,0 +1,24 @@ +Allwinner A10 SPI controller + +Required properties: +- compatible: Should be "allwinner,sun4-a10-spi". +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks: phandle to the clocks feeding the SPI controller. Two are + needed: + - "ahb": the gated AHB parent clock + - "mod": the parent module clock +- clock-names: Must contain the clock names described just above + +Example: + +spi1: spi@01c06000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c06000 0x1000>; + interrupts = <11>; + clocks = <&ahb_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-sun6i.txt b/Documentation/devicetree/bindings/spi/spi-sun6i.txt new file mode 100644 index 000000000..21de73db6 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-sun6i.txt @@ -0,0 +1,24 @@ +Allwinner A31 SPI controller + +Required properties: +- compatible: Should be "allwinner,sun6i-a31-spi". +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks: phandle to the clocks feeding the SPI controller. Two are + needed: + - "ahb": the gated AHB parent clock + - "mod": the parent module clock +- clock-names: Must contain the clock names described just above +- resets: phandle to the reset controller asserting this device in + reset + +Example: + +spi1: spi@01c69000 { + compatible = "allwinner,sun6i-a31-spi"; + reg = <0x01c69000 0x1000>; + interrupts = <0 66 4>; + clocks = <&ahb1_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + resets = <&ahb1_rst 21>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-xtensa-xtfpga.txt b/Documentation/devicetree/bindings/spi/spi-xtensa-xtfpga.txt new file mode 100644 index 000000000..b6ebe2bc7 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-xtensa-xtfpga.txt @@ -0,0 +1,9 @@ +Cadence Xtensa XTFPGA platform SPI controller. + +This simple SPI master controller is built into xtfpga bitstreams and is used +to control daughterboard audio codec. + +Required properties: +- compatible: should be "cdns,xtfpga-spi". +- reg: physical base address of the controller and length of memory mapped + region. diff --git a/Documentation/devicetree/bindings/spi/spi_altera.txt b/Documentation/devicetree/bindings/spi/spi_altera.txt new file mode 100644 index 000000000..31319dcf3 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_altera.txt @@ -0,0 +1,5 @@ +Altera SPI + +Required properties: +- compatible : should be "ALTR,spi-1.0". <DEPRECATED> +- compatible : should be "altr,spi-1.0". diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt new file mode 100644 index 000000000..4f8184d06 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt @@ -0,0 +1,31 @@ +Atmel SPI device + +Required properties: +- compatible : should be "atmel,at91rm9200-spi". +- reg: Address and length of the register set for the device +- interrupts: Should contain spi interrupt +- cs-gpios: chipselects +- clock-names: tuple listing input clock names. + Required elements: "spi_clk" +- clocks: phandles to input clocks. + +Example: + +spi1: spi@fffcc000 { + compatible = "atmel,at91rm9200-spi"; + reg = <0xfffcc000 0x4000>; + interrupts = <13 4 5>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&spi1_clk>; + clock-names = "spi_clk"; + cs-gpios = <&pioB 3 0>; + status = "okay"; + + mmc-slot@0 { + compatible = "mmc-spi-slot"; + reg = <0>; + gpios = <&pioC 4 0>; /* CD */ + spi-max-frequency = <25000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt b/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt new file mode 100644 index 000000000..d95c0b367 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_oc_tiny.txt @@ -0,0 +1,12 @@ +OpenCores tiny SPI + +Required properties: +- compatible : should be "opencores,tiny-spi-rtlsvn2". +- gpios : should specify GPIOs used for chipselect. +Optional properties: +- clock-frequency : input clock frequency to the core. +- baud-width: width, in bits, of the programmable divider used to scale + the input clock to SCLK. + +The clock-frequency and baud-width properties are needed only if the divider +is programmable. They are not needed if the divider is fixed. diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt new file mode 100644 index 000000000..4d1673ca8 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi_pl022.txt @@ -0,0 +1,70 @@ +ARM PL022 SPI controller + +Required properties: +- compatible : "arm,pl022", "arm,primecell" +- reg : Offset and length of the register set for the device +- interrupts : Should contain SPI controller interrupt +- num-cs : total number of chipselects + +Optional properties: +- cs-gpios : should specify GPIOs used for chipselects. + The gpios will be referred to as reg = <index> in the SPI child nodes. + If unspecified, a single SPI device without a chip select can be used. +- pl022,autosuspend-delay : delay in ms following transfer completion before + the runtime power management system suspends the + device. A setting of 0 indicates no delay and the + device will be suspended immediately +- pl022,rt : indicates the controller should run the message pump with realtime + priority to minimise the transfer latency on the bus (boolean) +- dmas : Two or more DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt +- dma-names: Names for the dma channels, if present. There must be at + least one channel named "tx" for transmit and named "rx" for + receive. + + +SPI slave nodes must be children of the SPI master node and can +contain the following properties. + +- pl022,interface : interface type: + 0: SPI + 1: Texas Instruments Synchronous Serial Frame Format + 2: Microwire (Half Duplex) +- pl022,com-mode : polling, interrupt or dma +- pl022,rx-level-trig : Rx FIFO watermark level +- pl022,tx-level-trig : Tx FIFO watermark level +- pl022,ctrl-len : Microwire interface: Control length +- pl022,wait-state : Microwire interface: Wait state +- pl022,duplex : Microwire interface: Full/Half duplex + + +Example: + + spi@e0100000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0xe0100000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 31 0x4>; + dmas = <&dma-controller 23 1>, + <&dma-controller 24 0>; + dma-names = "rx", "tx"; + + m25p80@1 { + compatible = "st,m25p80"; + reg = <1>; + spi-max-frequency = <12000000>; + spi-cpol; + spi-cpha; + pl022,hierarchy = <0>; + pl022,interface = <0>; + pl022,slave-tx-disable; + pl022,com-mode = <0x2>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + }; + }; + diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt new file mode 100644 index 000000000..601a36053 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -0,0 +1,28 @@ +TI QSPI controller. + +Required properties: +- compatible : should be "ti,dra7xxx-qspi" or "ti,am4372-qspi". +- reg: Should contain QSPI registers location and length. +- reg-names: Should contain the resource reg names. + - qspi_base: Qspi configuration register Address space + - qspi_mmap: Memory mapped Address space + - (optional) qspi_ctrlmod: Control module Address space +- interrupts: should contain the qspi interrupt number. +- #address-cells, #size-cells : Must be present if the device has sub-nodes +- ti,hwmods: Name of the hwmod associated to the QSPI + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +qspi: qspi@4b300000 { + compatible = "ti,dra7xxx-qspi"; + reg = <0x47900000 0x100>, <0x30000000 0x3ffffff>; + reg-names = "qspi_base", "qspi_mmap"; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <25000000>; + ti,hwmods = "qspi"; +}; |