Linux-libre 4.6.2-gnu

5 files changed, 110 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt b/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt
new file mode 100644
index 000000000..8a18d71e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt
@@ -0,0 +1,31 @@
+Analog Devices AXI SPI Engine controller Device Tree Bindings
+
+Required properties:
+- compatible		: Must be "adi,axi-spi-engine-1.00.a""
+- reg			: Physical base address and size of the register map.
+- interrupts		: Property with a value describing the interrupt
+			  number.
+- clock-names		: List of input clock names - "s_axi_aclk", "spi_clk"
+- clocks		: Clock phandles and specifiers (See clock bindings for
+			  details on clock-names and clocks).
+- #address-cells	: Must be <1>
+- #size-cells		: Must be <0>
+
+Optional subnodes:
+	Subnodes are use to represent the SPI slave devices connected to the SPI
+	master. They follow the generic SPI bindings as outlined in spi-bus.txt.
+
+Example:
+
+    spi@@44a00000 {
+		compatible = "adi,axi-spi-engine-1.00.a";
+		reg = <0x44a00000 0x1000>;
+		interrupts = <0 56 4>;
+		clocks = <&clkc 15 &clkc 15>;
+		clock-names = "s_axi_aclk", "spi_clk";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* SPI devices */
+    };
diff --git a/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt b/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt
new file mode 100644
index 000000000..852b651f3
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt
@@ -0,0 +1,54 @@
+* ICP DAS LP-8841 SPI Controller for RTC
+
+ICP DAS LP-8841 contains a DS-1302 RTC. RTC is connected to an IO
+memory register, which acts as an SPI master device.
+
+The device uses the standard MicroWire half-duplex transfer timing.
+Master output is set on low clock and sensed by the RTC on the rising
+edge. Master input is set by the RTC on the trailing edge and is sensed
+by the master on low clock.
+
+Required properties:
+
+- #address-cells: should be 1
+
+- #size-cells: should be 0
+
+- compatible: should be "icpdas,lp8841-spi-rtc"
+
+- reg: should provide IO memory address
+
+Requirements to SPI slave nodes:
+
+- There can be only one slave device.
+
+- The spi slave node should claim the following flags which are
+  required by the spi controller.
+
+  - spi-3wire: The master itself has only 3 wire. It cannor work in
+    full duplex mode.
+
+  - spi-cs-high: DS-1302 has active high chip select line. The master
+    doesn't support active low.
+
+  - spi-lsb-first: DS-1302 requires least significant bit first
+    transfers. The master only support this type of bit ordering.
+
+
+Example:
+
+spi@901c {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "icpdas,lp8841-spi-rtc";
+	reg = <0x901c 0x1>;
+
+	rtc@0 {
+		compatible = "maxim,ds1302";
+		reg = <0>;
+		spi-max-frequency = <500000>;
+		spi-3wire;
+		spi-lsb-first;
+		spi-cs-high;
+	};
+};
diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt
index bbaa857dd..42d595425 100644
--- a/Documentation/devicetree/bindings/spi/spi-bus.txt
+++ b/Documentation/devicetree/bindings/spi/spi-bus.txt
@@ -61,6 +61,8 @@ contain the following properties.
                       used for MOSI. Defaults to 1 if not present.
 - spi-rx-bus-width - (optional) The bus width(number of data wires) that
                       used for MISO. Defaults to 1 if not present.
+- spi-rx-delay-us  - (optional) Microsecond delay after a read transfer.
+- spi-tx-delay-us  - (optional) Microsecond delay after a write transfer.
 
 Some SPI controllers and devices support Dual and Quad SPI transfer mode.
 It allows data in the SPI system to be transferred in 2 wires(DUAL) or 4 wires(QUAD).
diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt
index 0c491bda4..1b14d69d8 100644
--- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt
+++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt
@@ -9,6 +9,7 @@ Required Properties:
     "rockchip,rk3066-spi" for rk3066.
     "rockchip,rk3188-spi", "rockchip,rk3066-spi" for rk3188.
     "rockchip,rk3288-spi", "rockchip,rk3066-spi" for rk3288.
+    "rockchip,rk3399-spi", "rockchip,rk3066-spi" for rk3399.
 - reg: physical base address of the controller and length of memory mapped
        region.
 - interrupts: The interrupt number to the cpu. The interrupt specifier format
diff --git a/Documentation/devicetree/bindings/spi/spi-xilinx.txt b/Documentation/devicetree/bindings/spi/spi-xilinx.txt
new file mode 100644
index 000000000..c7b7856bd
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-xilinx.txt
@@ -0,0 +1,22 @@
+Xilinx SPI controller Device Tree Bindings
+-------------------------------------------------
+
+Required properties:
+- compatible		: Should be "xlnx,xps-spi-2.00.a" or "xlnx,xps-spi-2.00.b"
+- reg			: Physical base address and size of SPI registers map.
+- interrupts		: Property with a value describing the interrupt
+			  number.
+- interrupt-parent	: Must be core interrupt controller
+
+Optional properties:
+- xlnx,num-ss-bits	: Number of chip selects used.
+
+Example:
+	axi_quad_spi@41e00000 {
+			compatible = "xlnx,xps-spi-2.00.a";
+			interrupt-parent = <&intc>;
+			interrupts = <0 31 1>;
+			reg = <0x41e00000 0x10000>;
+			xlnx,num-ss-bits = <0x1>;
+	};
+