Initial import

1 files changed, 297 insertions, 0 deletions

diff --git a/Documentation/video4linux/cx2341x/fw-decoder-api.txt b/Documentation/video4linux/cx2341x/fw-decoder-api.txt
new file mode 100644
index 000000000..8c317b7a4
--- /dev/null
+++ b/Documentation/video4linux/cx2341x/fw-decoder-api.txt
@@ -0,0 +1,297 @@
+Decoder firmware API description
+================================
+
+Note: this API is part of the decoder firmware, so it's cx23415 only.
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_PING_FW
+Enum 	0/0x00
+Description
+	This API call does nothing. It may be used to check if the firmware
+	is responding.
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_START_PLAYBACK
+Enum 	1/0x01
+Description
+	Begin or resume playback.
+Param[0]
+	0 based frame number in GOP to begin playback from.
+Param[1]
+	Specifies the number of muted audio frames to play before normal
+	audio resumes. (This is not implemented in the firmware, leave at 0)
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_STOP_PLAYBACK
+Enum 	2/0x02
+Description
+	Ends playback and clears all decoder buffers. If PTS is not zero,
+	playback stops at specified PTS.
+Param[0]
+	Display 0=last frame, 1=black
+	Note: this takes effect immediately, so if you want to wait for a PTS,
+	then use '0', otherwise the screen goes to black at once.
+	You can call this later (even if there is no playback) with a 1 value
+	to set the screen to black.
+Param[1]
+	PTS low
+Param[2]
+	PTS high
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_SET_PLAYBACK_SPEED
+Enum 	3/0x03
+Description
+	Playback stream at speed other than normal. There are two modes of
+	operation:
+	    Smooth: host transfers entire stream and firmware drops unused
+		    frames.
+	    Coarse: host drops frames based on indexing as required to achieve
+		    desired speed.
+Param[0]
+	Bitmap:
+	    0:7  0 normal
+		 1 fast only "1.5 times"
+		 n nX fast, 1/nX slow
+	    30   Framedrop:
+		     '0' during 1.5 times play, every other B frame is dropped
+		     '1' during 1.5 times play, stream is unchanged (bitrate
+			 must not exceed 8mbps)
+	    31   Speed:
+		     '0' slow
+		     '1' fast
+	Note: n is limited to 2. Anything higher does not result in
+	faster playback. Instead the host should start dropping frames.
+Param[1]
+	Direction: 0=forward, 1=reverse
+	Note: to make reverse playback work you have to write full GOPs in
+	reverse order.
+Param[2]
+	Picture mask:
+	    1=I frames
+	    3=I, P frames
+	    7=I, P, B frames
+Param[3]
+	B frames per GOP (for reverse play only)
+	Note: for reverse playback the Picture Mask should be set to I or I, P.
+	Adding B frames to the mask will result in corrupt video. This field
+	has to be set to the correct value in order to keep the timing correct.
+Param[4]
+	Mute audio: 0=disable, 1=enable
+Param[5]
+	Display 0=frame, 1=field
+Param[6]
+	Specifies the number of muted audio frames to play before normal audio
+	resumes. (Not implemented in the firmware, leave at 0)
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_STEP_VIDEO
+Enum 	5/0x05
+Description
+	Each call to this API steps the playback to the next unit defined below
+	in the current playback direction.
+Param[0]
+	0=frame, 1=top field, 2=bottom field
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_SET_DMA_BLOCK_SIZE
+Enum 	8/0x08
+Description
+	Set DMA transfer block size. Counterpart to API 0xC9
+Param[0]
+	DMA transfer block size in bytes. A different size may be specified
+	when issuing the DMA transfer command.
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_GET_XFER_INFO
+Enum 	9/0x09
+Description
+	This API call may be used to detect an end of stream condition.
+Result[0]
+	Stream type
+Result[1]
+	Address offset
+Result[2]
+	Maximum bytes to transfer
+Result[3]
+	Buffer fullness
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_GET_DMA_STATUS
+Enum 	10/0x0A
+Description
+	Status of the last DMA transfer
+Result[0]
+	Bit 1 set means transfer complete
+	Bit 2 set means DMA error
+	Bit 3 set means linked list error
+Result[1]
+	DMA type: 0=MPEG, 1=OSD, 2=YUV
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_SCHED_DMA_FROM_HOST
+Enum 	11/0x0B
+Description
+	Setup DMA from host operation. Counterpart to API 0xCC
+Param[0]
+	Memory address of link list
+Param[1]
+	Total # of bytes to transfer
+Param[2]
+	DMA type (0=MPEG, 1=OSD, 2=YUV)
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_PAUSE_PLAYBACK
+Enum 	13/0x0D
+Description
+	Freeze playback immediately. In this mode, when internal buffers are
+	full, no more data will be accepted and data request IRQs will be
+	masked.
+Param[0]
+	Display: 0=last frame, 1=black
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_HALT_FW
+Enum 	14/0x0E
+Description
+	The firmware is halted and no further API calls are serviced until
+	the firmware is uploaded again.
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_SET_STANDARD
+Enum 	16/0x10
+Description
+	Selects display standard
+Param[0]
+	0=NTSC, 1=PAL
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_GET_VERSION
+Enum 	17/0x11
+Description
+	Returns decoder firmware version information
+Result[0]
+	Version bitmask:
+	    Bits  0:15 build
+	    Bits 16:23 minor
+	    Bits 24:31 major
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_SET_STREAM_INPUT
+Enum 	20/0x14
+Description
+	Select decoder stream input port
+Param[0]
+	0=memory (default), 1=streaming
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_GET_TIMING_INFO
+Enum 	21/0x15
+Description
+	Returns timing information from start of playback
+Result[0]
+	Frame count by decode order
+Result[1]
+	Video PTS bits 0:31 by display order
+Result[2]
+	Video PTS bit 32 by display order
+Result[3]
+	SCR bits 0:31 by display order
+Result[4]
+	SCR bit 32 by display order
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_SET_AUDIO_MODE
+Enum 	22/0x16
+Description
+	Select audio mode
+Param[0]
+	Dual mono mode action
+	    0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
+Param[1]
+	Stereo mode action:
+	    0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_SET_EVENT_NOTIFICATION
+Enum 	23/0x17
+Description
+	Setup firmware to notify the host about a particular event.
+	Counterpart to API 0xD5
+Param[0]
+	Event: 0=Audio mode change between mono, (joint) stereo and dual channel.
+	Event: 3=Decoder started
+	Event: 4=Unknown: goes off 10-15 times per second while decoding.
+	Event: 5=Some sync event: goes off once per frame.
+Param[1]
+	Notification 0=disabled, 1=enabled
+Param[2]
+	Interrupt bit
+Param[3]
+	Mailbox slot, -1 if no mailbox required.
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_SET_DISPLAY_BUFFERS
+Enum 	24/0x18
+Description
+	Number of display buffers. To decode all frames in reverse playback you
+	must use nine buffers.
+Param[0]
+	0=six buffers, 1=nine buffers
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_EXTRACT_VBI
+Enum 	25/0x19
+Description
+	Extracts VBI data
+Param[0]
+	0=extract from extension & user data, 1=extract from private packets
+Result[0]
+	VBI table location
+Result[1]
+	VBI table size
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_SET_DECODER_SOURCE
+Enum 	26/0x1A
+Description
+	Selects decoder source. Ensure that the parameters passed to this
+	API match the encoder settings.
+Param[0]
+	Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host
+Param[1]
+	YUV picture width
+Param[2]
+	YUV picture height
+Param[3]
+	Bitmap: see Param[0] of API 0xBD
+
+-------------------------------------------------------------------------------
+
+Name 	CX2341X_DEC_SET_PREBUFFERING
+Enum 	30/0x1E
+Description
+	Decoder prebuffering, when enabled up to 128KB are buffered for
+	streams <8mpbs or 640KB for streams >8mbps
+Param[0]
+	0=off, 1=on