Linux-libre 4.3.2-gnu

4 files changed, 147 insertions, 81 deletions

diff --git a/arch/arm/mach-gemini/gpio.c b/arch/arm/mach-gemini/gpio.c
index 3292f2e6e..2478d9f4d 100644
--- a/arch/arm/mach-gemini/gpio.c
+++ b/arch/arm/mach-gemini/gpio.c
@@ -126,7 +126,7 @@ static int gpio_set_irq_type(struct irq_data *d, unsigned int type)
 	return 0;
 }
 
-static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void gpio_irq_handler(struct irq_desc *desc)
 {
 	unsigned int port = (unsigned int)irq_desc_get_handler_data(desc);
 	unsigned int gpio_irq_no, irq_stat;
@@ -220,7 +220,7 @@ void __init gemini_gpio_init(void)
 		     j < GPIO_IRQ_BASE + (i + 1) * 32; j++) {
 			irq_set_chip_and_handler(j, &gpio_irq_chip,
 						 handle_edge_irq);
-			set_irq_flags(j, IRQF_VALID);
+			irq_clear_status_flags(j, IRQ_NOREQUEST);
 		}
 
 		irq_set_chained_handler_and_data(IRQ_GPIO(i), gpio_irq_handler,
diff --git a/arch/arm/mach-gemini/include/mach/hardware.h b/arch/arm/mach-gemini/include/mach/hardware.h
index 98e7b0f28..f0390f184 100644
--- a/arch/arm/mach-gemini/include/mach/hardware.h
+++ b/arch/arm/mach-gemini/include/mach/hardware.h
@@ -57,9 +57,6 @@
 #define GEMINI_USB1_BASE	0x69000000
 #define GEMINI_BIG_ENDIAN_BASE	0x80000000
 
-#define GEMINI_TIMER1_BASE	GEMINI_TIMER_BASE
-#define GEMINI_TIMER2_BASE	(GEMINI_TIMER_BASE + 0x10)
-#define GEMINI_TIMER3_BASE	(GEMINI_TIMER_BASE + 0x20)
 
 /*
  * UART Clock when System clk is 150MHz
diff --git a/arch/arm/mach-gemini/irq.c b/arch/arm/mach-gemini/irq.c
index 44f50dcb6..d929b3ff1 100644
--- a/arch/arm/mach-gemini/irq.c
+++ b/arch/arm/mach-gemini/irq.c
@@ -92,7 +92,7 @@ void __init gemini_init_irq(void)
 		} else {			
 			irq_set_handler(i, handle_level_irq);
 		}
-		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(i, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 
 	/* Disable all interrupts */
diff --git a/arch/arm/mach-gemini/time.c b/arch/arm/mach-gemini/time.c
index 0a63c4d25..f5f18df5a 100644
--- a/arch/arm/mach-gemini/time.c
+++ b/arch/arm/mach-gemini/time.c
@@ -15,93 +15,147 @@
 #include <asm/mach/time.h>
 #include <linux/clockchips.h>
 #include <linux/clocksource.h>
+#include <linux/sched_clock.h>
 
 /*
  * Register definitions for the timers
  */
-#define TIMER_COUNT(BASE_ADDR)		(BASE_ADDR  + 0x00)
-#define TIMER_LOAD(BASE_ADDR)		(BASE_ADDR  + 0x04)
-#define TIMER_MATCH1(BASE_ADDR)		(BASE_ADDR  + 0x08)
-#define TIMER_MATCH2(BASE_ADDR)		(BASE_ADDR  + 0x0C)
-#define TIMER_CR(BASE_ADDR)		(BASE_ADDR  + 0x30)
-
-#define TIMER_1_CR_ENABLE		(1 << 0)
-#define TIMER_1_CR_CLOCK		(1 << 1)
-#define TIMER_1_CR_INT			(1 << 2)
-#define TIMER_2_CR_ENABLE		(1 << 3)
-#define TIMER_2_CR_CLOCK		(1 << 4)
-#define TIMER_2_CR_INT			(1 << 5)
-#define TIMER_3_CR_ENABLE		(1 << 6)
-#define TIMER_3_CR_CLOCK		(1 << 7)
-#define TIMER_3_CR_INT			(1 << 8)
+
+#define TIMER1_BASE		GEMINI_TIMER_BASE
+#define TIMER2_BASE		(GEMINI_TIMER_BASE + 0x10)
+#define TIMER3_BASE		(GEMINI_TIMER_BASE + 0x20)
+
+#define TIMER_COUNT(BASE)	(IO_ADDRESS(BASE) + 0x00)
+#define TIMER_LOAD(BASE)	(IO_ADDRESS(BASE) + 0x04)
+#define TIMER_MATCH1(BASE)	(IO_ADDRESS(BASE) + 0x08)
+#define TIMER_MATCH2(BASE)	(IO_ADDRESS(BASE) + 0x0C)
+#define TIMER_CR		(IO_ADDRESS(GEMINI_TIMER_BASE) + 0x30)
+#define TIMER_INTR_STATE	(IO_ADDRESS(GEMINI_TIMER_BASE) + 0x34)
+#define TIMER_INTR_MASK		(IO_ADDRESS(GEMINI_TIMER_BASE) + 0x38)
+
+#define TIMER_1_CR_ENABLE	(1 << 0)
+#define TIMER_1_CR_CLOCK	(1 << 1)
+#define TIMER_1_CR_INT		(1 << 2)
+#define TIMER_2_CR_ENABLE	(1 << 3)
+#define TIMER_2_CR_CLOCK	(1 << 4)
+#define TIMER_2_CR_INT		(1 << 5)
+#define TIMER_3_CR_ENABLE	(1 << 6)
+#define TIMER_3_CR_CLOCK	(1 << 7)
+#define TIMER_3_CR_INT		(1 << 8)
+#define TIMER_1_CR_UPDOWN	(1 << 9)
+#define TIMER_2_CR_UPDOWN	(1 << 10)
+#define TIMER_3_CR_UPDOWN	(1 << 11)
+#define TIMER_DEFAULT_FLAGS	(TIMER_1_CR_UPDOWN | \
+				 TIMER_3_CR_ENABLE | \
+				 TIMER_3_CR_UPDOWN)
+
+#define TIMER_1_INT_MATCH1	(1 << 0)
+#define TIMER_1_INT_MATCH2	(1 << 1)
+#define TIMER_1_INT_OVERFLOW	(1 << 2)
+#define TIMER_2_INT_MATCH1	(1 << 3)
+#define TIMER_2_INT_MATCH2	(1 << 4)
+#define TIMER_2_INT_OVERFLOW	(1 << 5)
+#define TIMER_3_INT_MATCH1	(1 << 6)
+#define TIMER_3_INT_MATCH2	(1 << 7)
+#define TIMER_3_INT_OVERFLOW	(1 << 8)
+#define TIMER_INT_ALL_MASK	0x1ff
+
 
 static unsigned int tick_rate;
 
+static u64 notrace gemini_read_sched_clock(void)
+{
+	return readl(TIMER_COUNT(TIMER3_BASE));
+}
+
 static int gemini_timer_set_next_event(unsigned long cycles,
 				       struct clock_event_device *evt)
 {
 	u32 cr;
 
-	cr = readl(TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
+	/* Setup the match register */
+	cr = readl(TIMER_COUNT(TIMER1_BASE));
+	writel(cr + cycles, TIMER_MATCH1(TIMER1_BASE));
+	if (readl(TIMER_COUNT(TIMER1_BASE)) - cr > cycles)
+		return -ETIME;
 
-	/* This may be overdoing it, feel free to test without this */
-	cr &= ~TIMER_2_CR_ENABLE;
-	cr &= ~TIMER_2_CR_INT;
-	writel(cr, TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
+	return 0;
+}
 
-	/* Set next event */
-	writel(cycles, TIMER_COUNT(IO_ADDRESS(GEMINI_TIMER2_BASE)));
-	writel(cycles, TIMER_LOAD(IO_ADDRESS(GEMINI_TIMER2_BASE)));
-	cr |= TIMER_2_CR_ENABLE;
-	cr |= TIMER_2_CR_INT;
-	writel(cr, TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
+static int gemini_timer_shutdown(struct clock_event_device *evt)
+{
+	u32 cr;
+
+	/*
+	 * Disable also for oneshot: the set_next() call will arm the timer
+	 * instead.
+	 */
+	/* Stop timer and interrupt. */
+	cr = readl(TIMER_CR);
+	cr &= ~(TIMER_1_CR_ENABLE | TIMER_1_CR_INT);
+	writel(cr, TIMER_CR);
+
+	/* Setup counter start from 0 */
+	writel(0, TIMER_COUNT(TIMER1_BASE));
+	writel(0, TIMER_LOAD(TIMER1_BASE));
+
+	/* enable interrupt */
+	cr = readl(TIMER_INTR_MASK);
+	cr &= ~(TIMER_1_INT_OVERFLOW | TIMER_1_INT_MATCH2);
+	cr |= TIMER_1_INT_MATCH1;
+	writel(cr, TIMER_INTR_MASK);
+
+	/* start the timer */
+	cr = readl(TIMER_CR);
+	cr |= TIMER_1_CR_ENABLE;
+	writel(cr, TIMER_CR);
 
 	return 0;
 }
 
-static void gemini_timer_set_mode(enum clock_event_mode mode,
-				  struct clock_event_device *evt)
+static int gemini_timer_set_periodic(struct clock_event_device *evt)
 {
 	u32 period = DIV_ROUND_CLOSEST(tick_rate, HZ);
 	u32 cr;
 
-	switch (mode) {
-        case CLOCK_EVT_MODE_PERIODIC:
-		/* Start the timer */
-		writel(period,
-		       TIMER_COUNT(IO_ADDRESS(GEMINI_TIMER2_BASE)));
-		writel(period,
-		       TIMER_LOAD(IO_ADDRESS(GEMINI_TIMER2_BASE)));
-		cr = readl(TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
-		cr |= TIMER_2_CR_ENABLE;
-		cr |= TIMER_2_CR_INT;
-		writel(cr, TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
-		break;
-	case CLOCK_EVT_MODE_ONESHOT:
-	case CLOCK_EVT_MODE_UNUSED:
-        case CLOCK_EVT_MODE_SHUTDOWN:
-	case CLOCK_EVT_MODE_RESUME:
-		/*
-		 * Disable also for oneshot: the set_next() call will
-		 * arm the timer instead.
-		 */
-		cr = readl(TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
-		cr &= ~TIMER_2_CR_ENABLE;
-		cr &= ~TIMER_2_CR_INT;
-		writel(cr, TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
-		break;
-	default:
-                break;
-	}
+	/* Stop timer and interrupt */
+	cr = readl(TIMER_CR);
+	cr &= ~(TIMER_1_CR_ENABLE | TIMER_1_CR_INT);
+	writel(cr, TIMER_CR);
+
+	/* Setup timer to fire at 1/HT intervals. */
+	cr = 0xffffffff - (period - 1);
+	writel(cr, TIMER_COUNT(TIMER1_BASE));
+	writel(cr, TIMER_LOAD(TIMER1_BASE));
+
+	/* enable interrupt on overflow */
+	cr = readl(TIMER_INTR_MASK);
+	cr &= ~(TIMER_1_INT_MATCH1 | TIMER_1_INT_MATCH2);
+	cr |= TIMER_1_INT_OVERFLOW;
+	writel(cr, TIMER_INTR_MASK);
+
+	/* Start the timer */
+	cr = readl(TIMER_CR);
+	cr |= TIMER_1_CR_ENABLE;
+	cr |= TIMER_1_CR_INT;
+	writel(cr, TIMER_CR);
+
+	return 0;
 }
 
-/* Use TIMER2 as clock event */
+/* Use TIMER1 as clock event */
 static struct clock_event_device gemini_clockevent = {
-	.name		= "TIMER2",
-	.rating		= 300, /* Reasonably fast and accurate clock event */
-	.features	= CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
-	.set_next_event	= gemini_timer_set_next_event,
-	.set_mode	= gemini_timer_set_mode,
+	.name			= "TIMER1",
+	/* Reasonably fast and accurate clock event */
+	.rating			= 300,
+	.shift                  = 32,
+	.features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT,
+	.set_next_event		= gemini_timer_set_next_event,
+	.set_state_shutdown	= gemini_timer_shutdown,
+	.set_state_periodic	= gemini_timer_set_periodic,
+	.set_state_oneshot	= gemini_timer_shutdown,
+	.tick_resume		= gemini_timer_shutdown,
 };
 
 /*
@@ -151,20 +205,35 @@ void __init gemini_timer_init(void)
 	}
 
 	/*
-	 * Make irqs happen for the system timer
+	 * Reset the interrupt mask and status
 	 */
-	setup_irq(IRQ_TIMER2, &gemini_timer_irq);
-
-	/* Enable and use TIMER1 as clock source */
-	writel(0xffffffff, TIMER_COUNT(IO_ADDRESS(GEMINI_TIMER1_BASE)));
-	writel(0xffffffff, TIMER_LOAD(IO_ADDRESS(GEMINI_TIMER1_BASE)));
-	writel(TIMER_1_CR_ENABLE, TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
-	if (clocksource_mmio_init(TIMER_COUNT(IO_ADDRESS(GEMINI_TIMER1_BASE)),
-				  "TIMER1", tick_rate, 300, 32,
-				  clocksource_mmio_readl_up))
-		pr_err("timer: failed to initialize gemini clock source\n");
-
-	/* Configure and register the clockevent */
+	writel(TIMER_INT_ALL_MASK, TIMER_INTR_MASK);
+	writel(0, TIMER_INTR_STATE);
+	writel(TIMER_DEFAULT_FLAGS, TIMER_CR);
+
+	/*
+	 * Setup free-running clocksource timer (interrupts
+	 * disabled.)
+	 */
+	writel(0, TIMER_COUNT(TIMER3_BASE));
+	writel(0, TIMER_LOAD(TIMER3_BASE));
+	writel(0, TIMER_MATCH1(TIMER3_BASE));
+	writel(0, TIMER_MATCH2(TIMER3_BASE));
+	clocksource_mmio_init(TIMER_COUNT(TIMER3_BASE),
+			      "gemini_clocksource", tick_rate,
+			      300, 32, clocksource_mmio_readl_up);
+	sched_clock_register(gemini_read_sched_clock, 32, tick_rate);
+
+	/*
+	 * Setup clockevent timer (interrupt-driven.)
+	*/
+	writel(0, TIMER_COUNT(TIMER1_BASE));
+	writel(0, TIMER_LOAD(TIMER1_BASE));
+	writel(0, TIMER_MATCH1(TIMER1_BASE));
+	writel(0, TIMER_MATCH2(TIMER1_BASE));
+	setup_irq(IRQ_TIMER1, &gemini_timer_irq);
+	gemini_clockevent.cpumask = cpumask_of(0);
 	clockevents_config_and_register(&gemini_clockevent, tick_rate,
 					1, 0xffffffff);
+
 }