Initial import

56 files changed, 6651 insertions, 0 deletions

diff --git a/arch/arm/plat-samsung/Kconfig b/arch/arm/plat-samsung/Kconfig
new file mode 100644
index 000000000..cb8e3d655
--- /dev/null
+++ b/arch/arm/plat-samsung/Kconfig
@@ -0,0 +1,323 @@
+# arch/arm/plat-samsung/Kconfig
+#
+# Copyright 2009 Simtec Electronics
+#
+# Licensed under GPLv2
+
+config PLAT_SAMSUNG
+	bool
+	depends on PLAT_S3C24XX || ARCH_S3C64XX || ARCH_EXYNOS || ARCH_S5PV210
+	default y
+	select GENERIC_IRQ_CHIP
+	select NO_IOPORT_MAP
+	help
+	  Base platform code for all Samsung SoC based systems
+
+config SAMSUNG_PM
+	bool
+	depends on PM && (PLAT_S3C24XX || ARCH_S3C64XX)
+	default y
+	help
+	  Base platform power management code for samsung code
+
+if PLAT_SAMSUNG
+menu "Samsung Common options"
+
+# boot configurations
+
+comment "Boot options"
+
+config S3C_LOWLEVEL_UART_PORT
+	int "S3C UART to use for low-level messages"
+	depends on ARCH_S3C64XX
+	default 0
+	help
+	  Choice of which UART port to use for the low-level messages,
+	  such as the `Uncompressing...` at start time. The value of
+	  this configuration should be between zero and two. The port
+	  must have been initialised by the boot-loader before use.
+
+config SAMSUNG_ATAGS
+	def_bool n
+	depends on !ARCH_MULTIPLATFORM
+	depends on ATAGS
+	help
+	   This option enables ATAGS based boot support code for
+	   Samsung platforms, including static platform devices, legacy
+	   clock, timer and interrupt initialization, etc.
+
+	   Platforms that support only DT based boot need not to select
+	   this option.
+
+if SAMSUNG_ATAGS
+
+config S3C_GPIO_SPACE
+	int "Space between gpio banks"
+	default 0
+	help
+	  Add a number of spare GPIO entries between each bank for debugging
+	  purposes. This allows any problems where an counter overflows from
+	  one bank to another to be caught, at the expense of using a little
+	  more memory.
+
+config S3C_GPIO_TRACK
+	bool
+	help
+	  Internal configuration option to enable the s3c specific gpio
+	  chip tracking if the platform requires it.
+
+# ADC driver
+
+config S3C_ADC
+	bool "ADC common driver support"
+	help
+	  Core support for the ADC block found in the Samsung SoC systems
+	  for drivers such as the touchscreen and hwmon to use to share
+	  this resource.
+
+# device definitions to compile in
+
+config S3C_DEV_HSMMC
+	bool
+	help
+	  Compile in platform device definitions for HSMMC code
+
+config S3C_DEV_HSMMC1
+	bool
+	help
+	  Compile in platform device definitions for HSMMC channel 1
+
+config S3C_DEV_HSMMC2
+	bool
+	help
+	  Compile in platform device definitions for HSMMC channel 2
+
+config S3C_DEV_HSMMC3
+	bool
+	help
+	  Compile in platform device definitions for HSMMC channel 3
+
+config S3C_DEV_HWMON
+	bool
+	help
+	    Compile in platform device definitions for HWMON
+
+config S3C_DEV_I2C1
+	bool
+	help
+	  Compile in platform device definitions for I2C channel 1
+
+config S3C_DEV_I2C2
+	bool
+	help
+	  Compile in platform device definitions for I2C channel 2
+
+config S3C_DEV_I2C3
+	bool
+	help
+	  Compile in platform device definition for I2C controller 3
+
+config S3C_DEV_I2C4
+	bool
+	help
+	  Compile in platform device definition for I2C controller 4
+
+config S3C_DEV_I2C5
+	bool
+	help
+	  Compile in platform device definition for I2C controller 5
+
+config S3C_DEV_I2C6
+	bool
+	help
+	  Compile in platform device definition for I2C controller 6
+
+config S3C_DEV_I2C7
+	bool
+	help
+	  Compile in platform device definition for I2C controller 7
+
+config S3C_DEV_FB
+	bool
+	help
+	  Compile in platform device definition for framebuffer
+
+config S3C_DEV_USB_HOST
+	bool
+	help
+	  Compile in platform device definition for USB host.
+
+config S3C_DEV_USB_HSOTG
+	bool
+	help
+	  Compile in platform device definition for USB high-speed OtG
+
+config S3C_DEV_WDT
+	bool
+	default y if ARCH_S3C24XX
+	help
+	  Complie in platform device definition for Watchdog Timer
+
+config S3C_DEV_NAND
+	bool
+	help
+	  Compile in platform device definition for NAND controller
+
+config S3C_DEV_ONENAND
+	bool
+	help
+	  Compile in platform device definition for OneNAND controller
+
+config S3C_DEV_RTC
+	bool
+	help
+	  Complie in platform device definition for RTC
+
+config SAMSUNG_DEV_ADC
+	bool
+	help
+	  Compile in platform device definition for ADC controller
+
+config SAMSUNG_DEV_IDE
+	bool
+	help
+	  Compile in platform device definitions for IDE
+
+config S3C64XX_DEV_SPI0
+	bool
+	help
+	  Compile in platform device definitions for S3C64XX's type
+	  SPI controller 0
+
+config S3C64XX_DEV_SPI1
+	bool
+	help
+	  Compile in platform device definitions for S3C64XX's type
+	  SPI controller 1
+
+config S3C64XX_DEV_SPI2
+	bool
+	help
+	  Compile in platform device definitions for S3C64XX's type
+	  SPI controller 2
+
+config SAMSUNG_DEV_TS
+	bool
+	help
+	    Common in platform device definitions for touchscreen device
+
+config SAMSUNG_DEV_KEYPAD
+	bool
+	help
+	  Compile in platform device definitions for keypad
+
+config SAMSUNG_DEV_PWM
+	bool
+	default y if ARCH_S3C24XX
+	help
+	  Compile in platform device definition for PWM Timer
+
+config SAMSUNG_DEV_BACKLIGHT
+	bool
+	depends on SAMSUNG_DEV_PWM
+	help
+	  Compile in platform device definition LCD backlight with PWM Timer
+
+config S3C24XX_PWM
+	bool "PWM device support"
+	select PWM
+	select PWM_SAMSUNG
+	help
+	  Support for exporting the PWM timer blocks via the pwm device
+	  system
+
+config S3C_SETUP_CAMIF
+	bool
+	help
+	  Compile in common setup code for S3C CAMIF devices
+
+config SAMSUNG_PM_GPIO
+	bool
+	default y if GPIO_SAMSUNG && PM
+	help
+	  Include legacy GPIO power management code for platforms not using
+	  pinctrl-samsung driver.
+
+endif
+
+config S5P_DEV_MFC
+	bool
+	help
+	  Compile in setup memory (init) code for MFC
+
+comment "Power management"
+
+config SAMSUNG_PM_DEBUG
+	bool "Samsung PM Suspend debug"
+	depends on PM && DEBUG_KERNEL
+	depends on DEBUG_EXYNOS_UART || DEBUG_S3C24XX_UART || DEBUG_S3C2410_UART
+	help
+	  Say Y here if you want verbose debugging from the PM Suspend and
+	  Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
+	  for more information.
+
+config S3C_PM_DEBUG_LED_SMDK
+       bool "SMDK LED suspend/resume debugging"
+       depends on PM && (MACH_SMDK6410)
+       help
+         Say Y here to enable the use of the SMDK LEDs on the baseboard
+	 for debugging of the state of the suspend and resume process.
+
+	 Note, this currently only works for S3C64XX based SMDK boards.
+
+config SAMSUNG_PM_CHECK
+	bool "S3C2410 PM Suspend Memory CRC"
+	depends on PM
+	select CRC32
+	help
+	  Enable the PM code's memory area checksum over sleep. This option
+	  will generate CRCs of all blocks of memory, and store them before
+	  going to sleep. The blocks are then checked on resume for any
+	  errors.
+
+	  Note, this can take several seconds depending on memory size
+	  and CPU speed.
+
+	  See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
+
+config SAMSUNG_PM_CHECK_CHUNKSIZE
+	int "S3C2410 PM Suspend CRC Chunksize (KiB)"
+	depends on PM && SAMSUNG_PM_CHECK
+	default 64
+	help
+	  Set the chunksize in Kilobytes of the CRC for checking memory
+	  corruption over suspend and resume. A smaller value will mean that
+	  the CRC data block will take more memory, but wil identify any
+	  faults with better precision.
+
+	  See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
+
+config SAMSUNG_WAKEMASK
+	bool
+	depends on PM
+	help
+	  Compile support for wakeup-mask controls found on the S3C6400
+	  and above. This code allows a set of interrupt to wakeup-mask
+	  mappings. See <plat/wakeup-mask.h>
+
+config SAMSUNG_WDT_RESET
+	bool
+	help
+	  Compile support for system restart by triggering watchdog reset.
+	  Used on SoCs that do not provide dedicated reset control.
+
+config DEBUG_S3C_UART
+	depends on PLAT_SAMSUNG
+	int
+	default "0" if DEBUG_S3C_UART0
+	default "1" if DEBUG_S3C_UART1
+	default "2" if DEBUG_S3C_UART2
+	default "3" if DEBUG_S3C_UART3
+
+endmenu
+endif
diff --git a/arch/arm/plat-samsung/Makefile b/arch/arm/plat-samsung/Makefile
new file mode 100644
index 000000000..1a29ab1f4
--- /dev/null
+++ b/arch/arm/plat-samsung/Makefile
@@ -0,0 +1,39 @@
+# arch/arm/plat-samsung/Makefile
+#
+# Copyright 2009 Simtec Electronics
+#
+# Licensed under GPLv2
+
+ccflags-$(CONFIG_ARCH_MULTI_V7) += -I$(srctree)/$(src)/include
+
+# Objects we always build independent of SoC choice
+
+obj-y				+= init.o cpu.o
+
+# ADC
+
+obj-$(CONFIG_S3C_ADC)	+= adc.o
+
+# devices
+
+obj-$(CONFIG_SAMSUNG_ATAGS)	+= platformdata.o
+
+obj-$(CONFIG_SAMSUNG_ATAGS)	+= devs.o
+obj-$(CONFIG_SAMSUNG_ATAGS)	+= dev-uart.o
+obj-$(CONFIG_S5P_DEV_MFC)	+= s5p-dev-mfc.o
+
+obj-$(CONFIG_SAMSUNG_DEV_BACKLIGHT)	+= dev-backlight.o
+
+obj-$(CONFIG_S3C_SETUP_CAMIF)	+= setup-camif.o
+
+# PM support
+
+obj-$(CONFIG_PM_SLEEP)		+= pm-common.o
+obj-$(CONFIG_EXYNOS_CPU_SUSPEND) += pm-common.o
+obj-$(CONFIG_SAMSUNG_PM)	+= pm.o
+obj-$(CONFIG_SAMSUNG_PM_GPIO)	+= pm-gpio.o
+obj-$(CONFIG_SAMSUNG_PM_CHECK)	+= pm-check.o
+obj-$(CONFIG_SAMSUNG_PM_DEBUG)	+= pm-debug.o
+
+obj-$(CONFIG_SAMSUNG_WAKEMASK)	+= wakeup-mask.o
+obj-$(CONFIG_SAMSUNG_WDT_RESET)	+= watchdog-reset.o
diff --git a/arch/arm/plat-samsung/adc.c b/arch/arm/plat-samsung/adc.c
new file mode 100644
index 000000000..e2be70df0
--- /dev/null
+++ b/arch/arm/plat-samsung/adc.c
@@ -0,0 +1,525 @@
+/* arch/arm/plat-samsung/adc.c
+ *
+ * Copyright (c) 2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>, <ben-linux@fluff.org>
+ *
+ * Samsung ADC device core
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+*/
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/sched.h>
+#include <linux/list.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/regulator/consumer.h>
+
+#include <plat/regs-adc.h>
+#include <plat/adc.h>
+
+/* This driver is designed to control the usage of the ADC block between
+ * the touchscreen and any other drivers that may need to use it, such as
+ * the hwmon driver.
+ *
+ * Priority will be given to the touchscreen driver, but as this itself is
+ * rate limited it should not starve other requests which are processed in
+ * order that they are received.
+ *
+ * Each user registers to get a client block which uniquely identifies it
+ * and stores information such as the necessary functions to callback when
+ * action is required.
+ */
+
+enum s3c_cpu_type {
+	TYPE_ADCV1, /* S3C24XX */
+	TYPE_ADCV11, /* S3C2443 */
+	TYPE_ADCV12, /* S3C2416, S3C2450 */
+	TYPE_ADCV2, /* S3C64XX */
+	TYPE_ADCV3, /* S5PV210, S5PC110, EXYNOS4210 */
+};
+
+struct s3c_adc_client {
+	struct platform_device	*pdev;
+	struct list_head	 pend;
+	wait_queue_head_t	*wait;
+
+	unsigned int		 nr_samples;
+	int			 result;
+	unsigned char		 is_ts;
+	unsigned char		 channel;
+
+	void	(*select_cb)(struct s3c_adc_client *c, unsigned selected);
+	void	(*convert_cb)(struct s3c_adc_client *c,
+			      unsigned val1, unsigned val2,
+			      unsigned *samples_left);
+};
+
+struct adc_device {
+	struct platform_device	*pdev;
+	struct platform_device	*owner;
+	struct clk		*clk;
+	struct s3c_adc_client	*cur;
+	struct s3c_adc_client	*ts_pend;
+	void __iomem		*regs;
+	spinlock_t		 lock;
+
+	unsigned int		 prescale;
+
+	int			 irq;
+	struct regulator	*vdd;
+};
+
+static struct adc_device *adc_dev;
+
+static LIST_HEAD(adc_pending);	/* protected by adc_device.lock */
+
+#define adc_dbg(_adc, msg...) dev_dbg(&(_adc)->pdev->dev, msg)
+
+static inline void s3c_adc_convert(struct adc_device *adc)
+{
+	unsigned con = readl(adc->regs + S3C2410_ADCCON);
+
+	con |= S3C2410_ADCCON_ENABLE_START;
+	writel(con, adc->regs + S3C2410_ADCCON);
+}
+
+static inline void s3c_adc_select(struct adc_device *adc,
+				  struct s3c_adc_client *client)
+{
+	unsigned con = readl(adc->regs + S3C2410_ADCCON);
+	enum s3c_cpu_type cpu = platform_get_device_id(adc->pdev)->driver_data;
+
+	client->select_cb(client, 1);
+
+	if (cpu == TYPE_ADCV1 || cpu == TYPE_ADCV2)
+		con &= ~S3C2410_ADCCON_MUXMASK;
+	con &= ~S3C2410_ADCCON_STDBM;
+	con &= ~S3C2410_ADCCON_STARTMASK;
+
+	if (!client->is_ts) {
+		if (cpu == TYPE_ADCV3)
+			writel(client->channel & 0xf, adc->regs + S5P_ADCMUX);
+		else if (cpu == TYPE_ADCV11 || cpu == TYPE_ADCV12)
+			writel(client->channel & 0xf,
+						adc->regs + S3C2443_ADCMUX);
+		else
+			con |= S3C2410_ADCCON_SELMUX(client->channel);
+	}
+
+	writel(con, adc->regs + S3C2410_ADCCON);
+}
+
+static void s3c_adc_dbgshow(struct adc_device *adc)
+{
+	adc_dbg(adc, "CON=%08x, TSC=%08x, DLY=%08x\n",
+		readl(adc->regs + S3C2410_ADCCON),
+		readl(adc->regs + S3C2410_ADCTSC),
+		readl(adc->regs + S3C2410_ADCDLY));
+}
+
+static void s3c_adc_try(struct adc_device *adc)
+{
+	struct s3c_adc_client *next = adc->ts_pend;
+
+	if (!next && !list_empty(&adc_pending)) {
+		next = list_first_entry(&adc_pending,
+					struct s3c_adc_client, pend);
+		list_del(&next->pend);
+	} else
+		adc->ts_pend = NULL;
+
+	if (next) {
+		adc_dbg(adc, "new client is %p\n", next);
+		adc->cur = next;
+		s3c_adc_select(adc, next);
+		s3c_adc_convert(adc);
+		s3c_adc_dbgshow(adc);
+	}
+}
+
+int s3c_adc_start(struct s3c_adc_client *client,
+		  unsigned int channel, unsigned int nr_samples)
+{
+	struct adc_device *adc = adc_dev;
+	unsigned long flags;
+
+	if (!adc) {
+		printk(KERN_ERR "%s: failed to find adc\n", __func__);
+		return -EINVAL;
+	}
+
+	spin_lock_irqsave(&adc->lock, flags);
+
+	if (client->is_ts && adc->ts_pend) {
+		spin_unlock_irqrestore(&adc->lock, flags);
+		return -EAGAIN;
+	}
+
+	client->channel = channel;
+	client->nr_samples = nr_samples;
+
+	if (client->is_ts)
+		adc->ts_pend = client;
+	else
+		list_add_tail(&client->pend, &adc_pending);
+
+	if (!adc->cur)
+		s3c_adc_try(adc);
+
+	spin_unlock_irqrestore(&adc->lock, flags);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(s3c_adc_start);
+
+static void s3c_convert_done(struct s3c_adc_client *client,
+			     unsigned v, unsigned u, unsigned *left)
+{
+	client->result = v;
+	wake_up(client->wait);
+}
+
+int s3c_adc_read(struct s3c_adc_client *client, unsigned int ch)
+{
+	DECLARE_WAIT_QUEUE_HEAD_ONSTACK(wake);
+	int ret;
+
+	client->convert_cb = s3c_convert_done;
+	client->wait = &wake;
+	client->result = -1;
+
+	ret = s3c_adc_start(client, ch, 1);
+	if (ret < 0)
+		goto err;
+
+	ret = wait_event_timeout(wake, client->result >= 0, HZ / 2);
+	if (client->result < 0) {
+		ret = -ETIMEDOUT;
+		goto err;
+	}
+
+	client->convert_cb = NULL;
+	return client->result;
+
+err:
+	return ret;
+}
+EXPORT_SYMBOL_GPL(s3c_adc_read);
+
+static void s3c_adc_default_select(struct s3c_adc_client *client,
+				   unsigned select)
+{
+}
+
+struct s3c_adc_client *s3c_adc_register(struct platform_device *pdev,
+					void (*select)(struct s3c_adc_client *client,
+						       unsigned int selected),
+					void (*conv)(struct s3c_adc_client *client,
+						     unsigned d0, unsigned d1,
+						     unsigned *samples_left),
+					unsigned int is_ts)
+{
+	struct s3c_adc_client *client;
+
+	WARN_ON(!pdev);
+
+	if (!select)
+		select = s3c_adc_default_select;
+
+	if (!pdev)
+		return ERR_PTR(-EINVAL);
+
+	client = kzalloc(sizeof(struct s3c_adc_client), GFP_KERNEL);
+	if (!client) {
+		dev_err(&pdev->dev, "no memory for adc client\n");
+		return ERR_PTR(-ENOMEM);
+	}
+
+	client->pdev = pdev;
+	client->is_ts = is_ts;
+	client->select_cb = select;
+	client->convert_cb = conv;
+
+	return client;
+}
+EXPORT_SYMBOL_GPL(s3c_adc_register);
+
+void s3c_adc_release(struct s3c_adc_client *client)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&adc_dev->lock, flags);
+
+	/* We should really check that nothing is in progress. */
+	if (adc_dev->cur == client)
+		adc_dev->cur = NULL;
+	if (adc_dev->ts_pend == client)
+		adc_dev->ts_pend = NULL;
+	else {
+		struct list_head *p, *n;
+		struct s3c_adc_client *tmp;
+
+		list_for_each_safe(p, n, &adc_pending) {
+			tmp = list_entry(p, struct s3c_adc_client, pend);
+			if (tmp == client)
+				list_del(&tmp->pend);
+		}
+	}
+
+	if (adc_dev->cur == NULL)
+		s3c_adc_try(adc_dev);
+
+	spin_unlock_irqrestore(&adc_dev->lock, flags);
+	kfree(client);
+}
+EXPORT_SYMBOL_GPL(s3c_adc_release);
+
+static irqreturn_t s3c_adc_irq(int irq, void *pw)
+{
+	struct adc_device *adc = pw;
+	struct s3c_adc_client *client = adc->cur;
+	enum s3c_cpu_type cpu = platform_get_device_id(adc->pdev)->driver_data;
+	unsigned data0, data1;
+
+	if (!client) {
+		dev_warn(&adc->pdev->dev, "%s: no adc pending\n", __func__);
+		goto exit;
+	}
+
+	data0 = readl(adc->regs + S3C2410_ADCDAT0);
+	data1 = readl(adc->regs + S3C2410_ADCDAT1);
+	adc_dbg(adc, "read %d: 0x%04x, 0x%04x\n", client->nr_samples, data0, data1);
+
+	client->nr_samples--;
+
+	if (cpu == TYPE_ADCV1 || cpu == TYPE_ADCV11) {
+		data0 &= 0x3ff;
+		data1 &= 0x3ff;
+	} else {
+		/* S3C2416/S3C64XX/S5P ADC resolution is 12-bit */
+		data0 &= 0xfff;
+		data1 &= 0xfff;
+	}
+
+	if (client->convert_cb)
+		(client->convert_cb)(client, data0, data1, &client->nr_samples);
+
+	if (client->nr_samples > 0) {
+		/* fire another conversion for this */
+
+		client->select_cb(client, 1);
+		s3c_adc_convert(adc);
+	} else {
+		spin_lock(&adc->lock);
+		(client->select_cb)(client, 0);
+		adc->cur = NULL;
+
+		s3c_adc_try(adc);
+		spin_unlock(&adc->lock);
+	}
+
+exit:
+	if (cpu == TYPE_ADCV2 || cpu == TYPE_ADCV3) {
+		/* Clear ADC interrupt */
+		writel(0, adc->regs + S3C64XX_ADCCLRINT);
+	}
+	return IRQ_HANDLED;
+}
+
+static int s3c_adc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct adc_device *adc;
+	struct resource *regs;
+	enum s3c_cpu_type cpu = platform_get_device_id(pdev)->driver_data;
+	int ret;
+	unsigned tmp;
+
+	adc = devm_kzalloc(dev, sizeof(struct adc_device), GFP_KERNEL);
+	if (adc == NULL) {
+		dev_err(dev, "failed to allocate adc_device\n");
+		return -ENOMEM;
+	}
+
+	spin_lock_init(&adc->lock);
+
+	adc->pdev = pdev;
+	adc->prescale = S3C2410_ADCCON_PRSCVL(49);
+
+	adc->vdd = devm_regulator_get(dev, "vdd");
+	if (IS_ERR(adc->vdd)) {
+		dev_err(dev, "operating without regulator \"vdd\" .\n");
+		return PTR_ERR(adc->vdd);
+	}
+
+	adc->irq = platform_get_irq(pdev, 1);
+	if (adc->irq <= 0) {
+		dev_err(dev, "failed to get adc irq\n");
+		return -ENOENT;
+	}
+
+	ret = devm_request_irq(dev, adc->irq, s3c_adc_irq, 0, dev_name(dev),
+				adc);
+	if (ret < 0) {
+		dev_err(dev, "failed to attach adc irq\n");
+		return ret;
+	}
+
+	adc->clk = devm_clk_get(dev, "adc");
+	if (IS_ERR(adc->clk)) {
+		dev_err(dev, "failed to get adc clock\n");
+		return PTR_ERR(adc->clk);
+	}
+
+	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	adc->regs = devm_ioremap_resource(dev, regs);
+	if (IS_ERR(adc->regs))
+		return PTR_ERR(adc->regs);
+
+	ret = regulator_enable(adc->vdd);
+	if (ret)
+		return ret;
+
+	clk_enable(adc->clk);
+
+	tmp = adc->prescale | S3C2410_ADCCON_PRSCEN;
+
+	/* Enable 12-bit ADC resolution */
+	if (cpu == TYPE_ADCV12)
+		tmp |= S3C2416_ADCCON_RESSEL;
+	if (cpu == TYPE_ADCV2 || cpu == TYPE_ADCV3)
+		tmp |= S3C64XX_ADCCON_RESSEL;
+
+	writel(tmp, adc->regs + S3C2410_ADCCON);
+
+	dev_info(dev, "attached adc driver\n");
+
+	platform_set_drvdata(pdev, adc);
+	adc_dev = adc;
+
+	return 0;
+}
+
+static int s3c_adc_remove(struct platform_device *pdev)
+{
+	struct adc_device *adc = platform_get_drvdata(pdev);
+
+	clk_disable(adc->clk);
+	regulator_disable(adc->vdd);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int s3c_adc_suspend(struct device *dev)
+{
+	struct platform_device *pdev = container_of(dev,
+			struct platform_device, dev);
+	struct adc_device *adc = platform_get_drvdata(pdev);
+	unsigned long flags;
+	u32 con;
+
+	spin_lock_irqsave(&adc->lock, flags);
+
+	con = readl(adc->regs + S3C2410_ADCCON);
+	con |= S3C2410_ADCCON_STDBM;
+	writel(con, adc->regs + S3C2410_ADCCON);
+
+	disable_irq(adc->irq);
+	spin_unlock_irqrestore(&adc->lock, flags);
+	clk_disable(adc->clk);
+	regulator_disable(adc->vdd);
+
+	return 0;
+}
+
+static int s3c_adc_resume(struct device *dev)
+{
+	struct platform_device *pdev = container_of(dev,
+			struct platform_device, dev);
+	struct adc_device *adc = platform_get_drvdata(pdev);
+	enum s3c_cpu_type cpu = platform_get_device_id(pdev)->driver_data;
+	int ret;
+	unsigned long tmp;
+
+	ret = regulator_enable(adc->vdd);
+	if (ret)
+		return ret;
+	clk_enable(adc->clk);
+	enable_irq(adc->irq);
+
+	tmp = adc->prescale | S3C2410_ADCCON_PRSCEN;
+
+	/* Enable 12-bit ADC resolution */
+	if (cpu == TYPE_ADCV12)
+		tmp |= S3C2416_ADCCON_RESSEL;
+	if (cpu == TYPE_ADCV2 || cpu == TYPE_ADCV3)
+		tmp |= S3C64XX_ADCCON_RESSEL;
+
+	writel(tmp, adc->regs + S3C2410_ADCCON);
+
+	return 0;
+}
+
+#else
+#define s3c_adc_suspend NULL
+#define s3c_adc_resume NULL
+#endif
+
+static struct platform_device_id s3c_adc_driver_ids[] = {
+	{
+		.name           = "s3c24xx-adc",
+		.driver_data    = TYPE_ADCV1,
+	}, {
+		.name		= "s3c2443-adc",
+		.driver_data	= TYPE_ADCV11,
+	}, {
+		.name		= "s3c2416-adc",
+		.driver_data	= TYPE_ADCV12,
+	}, {
+		.name           = "s3c64xx-adc",
+		.driver_data    = TYPE_ADCV2,
+	}, {
+		.name		= "samsung-adc-v3",
+		.driver_data	= TYPE_ADCV3,
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(platform, s3c_adc_driver_ids);
+
+static const struct dev_pm_ops adc_pm_ops = {
+	.suspend	= s3c_adc_suspend,
+	.resume		= s3c_adc_resume,
+};
+
+static struct platform_driver s3c_adc_driver = {
+	.id_table	= s3c_adc_driver_ids,
+	.driver		= {
+		.name	= "s3c-adc",
+		.pm	= &adc_pm_ops,
+	},
+	.probe		= s3c_adc_probe,
+	.remove		= s3c_adc_remove,
+};
+
+static int __init adc_init(void)
+{
+	int ret;
+
+	ret = platform_driver_register(&s3c_adc_driver);
+	if (ret)
+		printk(KERN_ERR "%s: failed to add adc driver\n", __func__);
+
+	return ret;
+}
+
+module_init(adc_init);
diff --git a/arch/arm/plat-samsung/cpu.c b/arch/arm/plat-samsung/cpu.c
new file mode 100644
index 000000000..71333bb61
--- /dev/null
+++ b/arch/arm/plat-samsung/cpu.c
@@ -0,0 +1,53 @@
+/* linux/arch/arm/plat-samsung/cpu.c
+ *
+ * Copyright (c) 2009-2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung CPU Support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+
+#include <plat/map-base.h>
+#include <plat/cpu.h>
+
+unsigned long samsung_cpu_id;
+static unsigned int samsung_cpu_rev;
+
+unsigned int samsung_rev(void)
+{
+	return samsung_cpu_rev;
+}
+EXPORT_SYMBOL(samsung_rev);
+
+void __init s3c64xx_init_cpu(void)
+{
+	samsung_cpu_id = __raw_readl(S3C_VA_SYS + 0x118);
+	if (!samsung_cpu_id) {
+		/*
+		 * S3C6400 has the ID register in a different place,
+		 * and needs a write before it can be read.
+		 */
+		__raw_writel(0x0, S3C_VA_SYS + 0xA1C);
+		samsung_cpu_id = __raw_readl(S3C_VA_SYS + 0xA1C);
+	}
+
+	samsung_cpu_rev = 0;
+
+	pr_info("Samsung CPU ID: 0x%08lx\n", samsung_cpu_id);
+}
+
+void __init s5p_init_cpu(void __iomem *cpuid_addr)
+{
+	samsung_cpu_id = __raw_readl(cpuid_addr);
+	samsung_cpu_rev = samsung_cpu_id & 0xFF;
+
+	pr_info("Samsung CPU ID: 0x%08lx\n", samsung_cpu_id);
+}
diff --git a/arch/arm/plat-samsung/dev-backlight.c b/arch/arm/plat-samsung/dev-backlight.c
new file mode 100644
index 000000000..2157c5b53
--- /dev/null
+++ b/arch/arm/plat-samsung/dev-backlight.c
@@ -0,0 +1,152 @@
+/* linux/arch/arm/plat-samsung/dev-backlight.c
+ *
+ * Copyright (c) 2011 Samsung Electronics Co., Ltd.
+ *              http://www.samsung.com
+ *
+ * Common infrastructure for PWM Backlight for Samsung boards
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/io.h>
+#include <linux/pwm_backlight.h>
+
+#include <plat/devs.h>
+#include <plat/gpio-cfg.h>
+#include <plat/backlight.h>
+
+struct samsung_bl_drvdata {
+	struct platform_pwm_backlight_data plat_data;
+	struct samsung_bl_gpio_info *gpio_info;
+};
+
+static int samsung_bl_init(struct device *dev)
+{
+	int ret = 0;
+	struct platform_pwm_backlight_data *pdata = dev->platform_data;
+	struct samsung_bl_drvdata *drvdata = container_of(pdata,
+					struct samsung_bl_drvdata, plat_data);
+	struct samsung_bl_gpio_info *bl_gpio_info = drvdata->gpio_info;
+
+	ret = gpio_request(bl_gpio_info->no, "Backlight");
+	if (ret) {
+		printk(KERN_ERR "failed to request GPIO for LCD Backlight\n");
+		return ret;
+	}
+
+	/* Configure GPIO pin with specific GPIO function for PWM timer */
+	s3c_gpio_cfgpin(bl_gpio_info->no, bl_gpio_info->func);
+
+	return 0;
+}
+
+static void samsung_bl_exit(struct device *dev)
+{
+	struct platform_pwm_backlight_data *pdata = dev->platform_data;
+	struct samsung_bl_drvdata *drvdata = container_of(pdata,
+					struct samsung_bl_drvdata, plat_data);
+	struct samsung_bl_gpio_info *bl_gpio_info = drvdata->gpio_info;
+
+	s3c_gpio_cfgpin(bl_gpio_info->no, S3C_GPIO_OUTPUT);
+	gpio_free(bl_gpio_info->no);
+}
+
+/* Initialize few important fields of platform_pwm_backlight_data
+ * structure with default values. These fields can be overridden by
+ * board-specific values sent from machine file.
+ * For ease of operation, these fields are initialized with values
+ * used by most samsung boards.
+ * Users has the option of sending info about other parameters
+ * for their specific boards
+ */
+
+static struct samsung_bl_drvdata samsung_dfl_bl_data __initdata = {
+	.plat_data = {
+		.max_brightness = 255,
+		.dft_brightness = 255,
+		.pwm_period_ns  = 78770,
+		.enable_gpio    = -1,
+		.init           = samsung_bl_init,
+		.exit           = samsung_bl_exit,
+	},
+};
+
+static struct platform_device samsung_dfl_bl_device __initdata = {
+	.name		= "pwm-backlight",
+};
+
+/* samsung_bl_set - Set board specific data (if any) provided by user for
+ * PWM Backlight control and register specific PWM and backlight device.
+ * @gpio_info:	structure containing GPIO info for PWM timer
+ * @bl_data:	structure containing Backlight control data
+ */
+void __init samsung_bl_set(struct samsung_bl_gpio_info *gpio_info,
+	struct platform_pwm_backlight_data *bl_data)
+{
+	int ret = 0;
+	struct platform_device *samsung_bl_device;
+	struct samsung_bl_drvdata *samsung_bl_drvdata;
+	struct platform_pwm_backlight_data *samsung_bl_data;
+
+	samsung_bl_device = kmemdup(&samsung_dfl_bl_device,
+			sizeof(struct platform_device), GFP_KERNEL);
+	if (!samsung_bl_device) {
+		printk(KERN_ERR "%s: no memory for platform dev\n", __func__);
+		return;
+	}
+
+	samsung_bl_drvdata = kmemdup(&samsung_dfl_bl_data,
+				sizeof(samsung_dfl_bl_data), GFP_KERNEL);
+	if (!samsung_bl_drvdata) {
+		printk(KERN_ERR "%s: no memory for platform dev\n", __func__);
+		goto err_data;
+	}
+	samsung_bl_device->dev.platform_data = &samsung_bl_drvdata->plat_data;
+	samsung_bl_drvdata->gpio_info = gpio_info;
+	samsung_bl_data = &samsung_bl_drvdata->plat_data;
+
+	/* Copy board specific data provided by user */
+	samsung_bl_data->pwm_id = bl_data->pwm_id;
+	samsung_bl_device->dev.parent = &samsung_device_pwm.dev;
+
+	if (bl_data->max_brightness)
+		samsung_bl_data->max_brightness = bl_data->max_brightness;
+	if (bl_data->dft_brightness)
+		samsung_bl_data->dft_brightness = bl_data->dft_brightness;
+	if (bl_data->lth_brightness)
+		samsung_bl_data->lth_brightness = bl_data->lth_brightness;
+	if (bl_data->pwm_period_ns)
+		samsung_bl_data->pwm_period_ns = bl_data->pwm_period_ns;
+	if (bl_data->enable_gpio >= 0)
+		samsung_bl_data->enable_gpio = bl_data->enable_gpio;
+	if (bl_data->init)
+		samsung_bl_data->init = bl_data->init;
+	if (bl_data->notify)
+		samsung_bl_data->notify = bl_data->notify;
+	if (bl_data->notify_after)
+		samsung_bl_data->notify_after = bl_data->notify_after;
+	if (bl_data->exit)
+		samsung_bl_data->exit = bl_data->exit;
+	if (bl_data->check_fb)
+		samsung_bl_data->check_fb = bl_data->check_fb;
+
+	/* Register the Backlight dev */
+	ret = platform_device_register(samsung_bl_device);
+	if (ret) {
+		printk(KERN_ERR "failed to register backlight device: %d\n", ret);
+		goto err_plat_reg2;
+	}
+
+	return;
+
+err_plat_reg2:
+	kfree(samsung_bl_data);
+err_data:
+	kfree(samsung_bl_device);
+	return;
+}
diff --git a/arch/arm/plat-samsung/dev-uart.c b/arch/arm/plat-samsung/dev-uart.c
new file mode 100644
index 000000000..592810549
--- /dev/null
+++ b/arch/arm/plat-samsung/dev-uart.c
@@ -0,0 +1,46 @@
+/* linux/arch/arm/plat-samsung/dev-uart.c
+ *	originally from arch/arm/plat-s3c24xx/devs.c
+ *x
+ * Copyright (c) 2004 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Base S3C24XX platform device definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+
+#include <plat/devs.h>
+
+/* uart devices */
+
+static struct platform_device s3c24xx_uart_device0 = {
+	.id		= 0,
+};
+
+static struct platform_device s3c24xx_uart_device1 = {
+	.id		= 1,
+};
+
+static struct platform_device s3c24xx_uart_device2 = {
+	.id		= 2,
+};
+
+static struct platform_device s3c24xx_uart_device3 = {
+	.id		= 3,
+};
+
+struct platform_device *s3c24xx_uart_src[4] = {
+	&s3c24xx_uart_device0,
+	&s3c24xx_uart_device1,
+	&s3c24xx_uart_device2,
+	&s3c24xx_uart_device3,
+};
+
+struct platform_device *s3c24xx_uart_devs[4] = {
+};
diff --git a/arch/arm/plat-samsung/devs.c b/arch/arm/plat-samsung/devs.c
new file mode 100644
index 000000000..83c7d154b
--- /dev/null
+++ b/arch/arm/plat-samsung/devs.c
@@ -0,0 +1,1229 @@
+/* linux/arch/arm/plat-samsung/devs.c
+ *
+ * Copyright (c) 2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Base SAMSUNG platform device definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/amba/pl330.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/dma-mapping.h>
+#include <linux/fb.h>
+#include <linux/gfp.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/onenand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mmc/host.h>
+#include <linux/ioport.h>
+#include <linux/sizes.h>
+#include <linux/platform_data/s3c-hsudc.h>
+#include <linux/platform_data/s3c-hsotg.h>
+#include <linux/platform_data/dma-s3c24xx.h>
+
+#include <media/s5p_hdmi.h>
+
+#include <asm/irq.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/dma.h>
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+#include <plat/cpu.h>
+#include <plat/devs.h>
+#include <plat/adc.h>
+#include <linux/platform_data/ata-samsung_cf.h>
+#include <plat/fb.h>
+#include <plat/fb-s3c2410.h>
+#include <linux/platform_data/hwmon-s3c.h>
+#include <linux/platform_data/i2c-s3c2410.h>
+#include <plat/keypad.h>
+#include <linux/platform_data/mmc-s3cmci.h>
+#include <linux/platform_data/mtd-nand-s3c2410.h>
+#include <plat/pwm-core.h>
+#include <plat/sdhci.h>
+#include <linux/platform_data/touchscreen-s3c2410.h>
+#include <linux/platform_data/usb-s3c2410_udc.h>
+#include <linux/platform_data/usb-ohci-s3c2410.h>
+#include <plat/usb-phy.h>
+#include <plat/regs-spi.h>
+#include <linux/platform_data/spi-s3c64xx.h>
+
+static u64 samsung_device_dma_mask = DMA_BIT_MASK(32);
+
+/* AC97 */
+#ifdef CONFIG_CPU_S3C2440
+static struct resource s3c_ac97_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C2440_PA_AC97, S3C2440_SZ_AC97),
+	[1] = DEFINE_RES_IRQ(IRQ_S3C244X_AC97),
+	[2] = DEFINE_RES_DMA_NAMED(DMACH_PCM_OUT, "PCM out"),
+	[3] = DEFINE_RES_DMA_NAMED(DMACH_PCM_IN, "PCM in"),
+	[4] = DEFINE_RES_DMA_NAMED(DMACH_MIC_IN, "Mic in"),
+};
+
+struct platform_device s3c_device_ac97 = {
+	.name		= "samsung-ac97",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_ac97_resource),
+	.resource	= s3c_ac97_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	}
+};
+#endif /* CONFIG_CPU_S3C2440 */
+
+/* ADC */
+
+#ifdef CONFIG_PLAT_S3C24XX
+static struct resource s3c_adc_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C24XX_PA_ADC, S3C24XX_SZ_ADC),
+	[1] = DEFINE_RES_IRQ(IRQ_TC),
+	[2] = DEFINE_RES_IRQ(IRQ_ADC),
+};
+
+struct platform_device s3c_device_adc = {
+	.name		= "s3c24xx-adc",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_adc_resource),
+	.resource	= s3c_adc_resource,
+};
+#endif /* CONFIG_PLAT_S3C24XX */
+
+#if defined(CONFIG_SAMSUNG_DEV_ADC)
+static struct resource s3c_adc_resource[] = {
+	[0] = DEFINE_RES_MEM(SAMSUNG_PA_ADC, SZ_256),
+	[1] = DEFINE_RES_IRQ(IRQ_TC),
+	[2] = DEFINE_RES_IRQ(IRQ_ADC),
+};
+
+struct platform_device s3c_device_adc = {
+	.name		= "samsung-adc",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_adc_resource),
+	.resource	= s3c_adc_resource,
+};
+#endif /* CONFIG_SAMSUNG_DEV_ADC */
+
+/* Camif Controller */
+
+#ifdef CONFIG_CPU_S3C2440
+static struct resource s3c_camif_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C2440_PA_CAMIF, S3C2440_SZ_CAMIF),
+	[1] = DEFINE_RES_IRQ(IRQ_S3C2440_CAM_C),
+	[2] = DEFINE_RES_IRQ(IRQ_S3C2440_CAM_P),
+};
+
+struct platform_device s3c_device_camif = {
+	.name		= "s3c2440-camif",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_camif_resource),
+	.resource	= s3c_camif_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	}
+};
+#endif /* CONFIG_CPU_S3C2440 */
+
+/* FB */
+
+#ifdef CONFIG_S3C_DEV_FB
+static struct resource s3c_fb_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_FB, SZ_16K),
+	[1] = DEFINE_RES_IRQ(IRQ_LCD_VSYNC),
+	[2] = DEFINE_RES_IRQ(IRQ_LCD_FIFO),
+	[3] = DEFINE_RES_IRQ(IRQ_LCD_SYSTEM),
+};
+
+struct platform_device s3c_device_fb = {
+	.name		= "s3c-fb",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_fb_resource),
+	.resource	= s3c_fb_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+void __init s3c_fb_set_platdata(struct s3c_fb_platdata *pd)
+{
+	s3c_set_platdata(pd, sizeof(struct s3c_fb_platdata),
+			 &s3c_device_fb);
+}
+#endif /* CONFIG_S3C_DEV_FB */
+
+/* HWMON */
+
+#ifdef CONFIG_S3C_DEV_HWMON
+struct platform_device s3c_device_hwmon = {
+	.name		= "s3c-hwmon",
+	.id		= -1,
+	.dev.parent	= &s3c_device_adc.dev,
+};
+
+void __init s3c_hwmon_set_platdata(struct s3c_hwmon_pdata *pd)
+{
+	s3c_set_platdata(pd, sizeof(struct s3c_hwmon_pdata),
+			 &s3c_device_hwmon);
+}
+#endif /* CONFIG_S3C_DEV_HWMON */
+
+/* HSMMC */
+
+#ifdef CONFIG_S3C_DEV_HSMMC
+static struct resource s3c_hsmmc_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_HSMMC0, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_HSMMC0),
+};
+
+struct s3c_sdhci_platdata s3c_hsmmc0_def_platdata = {
+	.max_width	= 4,
+	.host_caps	= (MMC_CAP_4_BIT_DATA |
+			   MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED),
+};
+
+struct platform_device s3c_device_hsmmc0 = {
+	.name		= "s3c-sdhci",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(s3c_hsmmc_resource),
+	.resource	= s3c_hsmmc_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &s3c_hsmmc0_def_platdata,
+	},
+};
+
+void s3c_sdhci0_set_platdata(struct s3c_sdhci_platdata *pd)
+{
+	s3c_sdhci_set_platdata(pd, &s3c_hsmmc0_def_platdata);
+}
+#endif /* CONFIG_S3C_DEV_HSMMC */
+
+#ifdef CONFIG_S3C_DEV_HSMMC1
+static struct resource s3c_hsmmc1_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_HSMMC1, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_HSMMC1),
+};
+
+struct s3c_sdhci_platdata s3c_hsmmc1_def_platdata = {
+	.max_width	= 4,
+	.host_caps	= (MMC_CAP_4_BIT_DATA |
+			   MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED),
+};
+
+struct platform_device s3c_device_hsmmc1 = {
+	.name		= "s3c-sdhci",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(s3c_hsmmc1_resource),
+	.resource	= s3c_hsmmc1_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &s3c_hsmmc1_def_platdata,
+	},
+};
+
+void s3c_sdhci1_set_platdata(struct s3c_sdhci_platdata *pd)
+{
+	s3c_sdhci_set_platdata(pd, &s3c_hsmmc1_def_platdata);
+}
+#endif /* CONFIG_S3C_DEV_HSMMC1 */
+
+/* HSMMC2 */
+
+#ifdef CONFIG_S3C_DEV_HSMMC2
+static struct resource s3c_hsmmc2_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_HSMMC2, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_HSMMC2),
+};
+
+struct s3c_sdhci_platdata s3c_hsmmc2_def_platdata = {
+	.max_width	= 4,
+	.host_caps	= (MMC_CAP_4_BIT_DATA |
+			   MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED),
+};
+
+struct platform_device s3c_device_hsmmc2 = {
+	.name		= "s3c-sdhci",
+	.id		= 2,
+	.num_resources	= ARRAY_SIZE(s3c_hsmmc2_resource),
+	.resource	= s3c_hsmmc2_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &s3c_hsmmc2_def_platdata,
+	},
+};
+
+void s3c_sdhci2_set_platdata(struct s3c_sdhci_platdata *pd)
+{
+	s3c_sdhci_set_platdata(pd, &s3c_hsmmc2_def_platdata);
+}
+#endif /* CONFIG_S3C_DEV_HSMMC2 */
+
+#ifdef CONFIG_S3C_DEV_HSMMC3
+static struct resource s3c_hsmmc3_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_HSMMC3, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_HSMMC3),
+};
+
+struct s3c_sdhci_platdata s3c_hsmmc3_def_platdata = {
+	.max_width	= 4,
+	.host_caps	= (MMC_CAP_4_BIT_DATA |
+			   MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED),
+};
+
+struct platform_device s3c_device_hsmmc3 = {
+	.name		= "s3c-sdhci",
+	.id		= 3,
+	.num_resources	= ARRAY_SIZE(s3c_hsmmc3_resource),
+	.resource	= s3c_hsmmc3_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+		.platform_data		= &s3c_hsmmc3_def_platdata,
+	},
+};
+
+void s3c_sdhci3_set_platdata(struct s3c_sdhci_platdata *pd)
+{
+	s3c_sdhci_set_platdata(pd, &s3c_hsmmc3_def_platdata);
+}
+#endif /* CONFIG_S3C_DEV_HSMMC3 */
+
+/* I2C */
+
+static struct resource s3c_i2c0_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_IIC, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_IIC),
+};
+
+struct platform_device s3c_device_i2c0 = {
+	.name		= "s3c2410-i2c",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(s3c_i2c0_resource),
+	.resource	= s3c_i2c0_resource,
+};
+
+struct s3c2410_platform_i2c default_i2c_data __initdata = {
+	.flags		= 0,
+	.slave_addr	= 0x10,
+	.frequency	= 100*1000,
+	.sda_delay	= 100,
+};
+
+void __init s3c_i2c0_set_platdata(struct s3c2410_platform_i2c *pd)
+{
+	struct s3c2410_platform_i2c *npd;
+
+	if (!pd) {
+		pd = &default_i2c_data;
+		pd->bus_num = 0;
+	}
+
+	npd = s3c_set_platdata(pd, sizeof(struct s3c2410_platform_i2c),
+			       &s3c_device_i2c0);
+
+	if (!npd->cfg_gpio)
+		npd->cfg_gpio = s3c_i2c0_cfg_gpio;
+}
+
+#ifdef CONFIG_S3C_DEV_I2C1
+static struct resource s3c_i2c1_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_IIC1, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_IIC1),
+};
+
+struct platform_device s3c_device_i2c1 = {
+	.name		= "s3c2410-i2c",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(s3c_i2c1_resource),
+	.resource	= s3c_i2c1_resource,
+};
+
+void __init s3c_i2c1_set_platdata(struct s3c2410_platform_i2c *pd)
+{
+	struct s3c2410_platform_i2c *npd;
+
+	if (!pd) {
+		pd = &default_i2c_data;
+		pd->bus_num = 1;
+	}
+
+	npd = s3c_set_platdata(pd, sizeof(struct s3c2410_platform_i2c),
+			       &s3c_device_i2c1);
+
+	if (!npd->cfg_gpio)
+		npd->cfg_gpio = s3c_i2c1_cfg_gpio;
+}
+#endif /* CONFIG_S3C_DEV_I2C1 */
+
+#ifdef CONFIG_S3C_DEV_I2C2
+static struct resource s3c_i2c2_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_IIC2, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_IIC2),
+};
+
+struct platform_device s3c_device_i2c2 = {
+	.name		= "s3c2410-i2c",
+	.id		= 2,
+	.num_resources	= ARRAY_SIZE(s3c_i2c2_resource),
+	.resource	= s3c_i2c2_resource,
+};
+
+void __init s3c_i2c2_set_platdata(struct s3c2410_platform_i2c *pd)
+{
+	struct s3c2410_platform_i2c *npd;
+
+	if (!pd) {
+		pd = &default_i2c_data;
+		pd->bus_num = 2;
+	}
+
+	npd = s3c_set_platdata(pd, sizeof(struct s3c2410_platform_i2c),
+			       &s3c_device_i2c2);
+
+	if (!npd->cfg_gpio)
+		npd->cfg_gpio = s3c_i2c2_cfg_gpio;
+}
+#endif /* CONFIG_S3C_DEV_I2C2 */
+
+#ifdef CONFIG_S3C_DEV_I2C3
+static struct resource s3c_i2c3_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_IIC3, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_IIC3),
+};
+
+struct platform_device s3c_device_i2c3 = {
+	.name		= "s3c2440-i2c",
+	.id		= 3,
+	.num_resources	= ARRAY_SIZE(s3c_i2c3_resource),
+	.resource	= s3c_i2c3_resource,
+};
+
+void __init s3c_i2c3_set_platdata(struct s3c2410_platform_i2c *pd)
+{
+	struct s3c2410_platform_i2c *npd;
+
+	if (!pd) {
+		pd = &default_i2c_data;
+		pd->bus_num = 3;
+	}
+
+	npd = s3c_set_platdata(pd, sizeof(struct s3c2410_platform_i2c),
+			       &s3c_device_i2c3);
+
+	if (!npd->cfg_gpio)
+		npd->cfg_gpio = s3c_i2c3_cfg_gpio;
+}
+#endif /*CONFIG_S3C_DEV_I2C3 */
+
+#ifdef CONFIG_S3C_DEV_I2C4
+static struct resource s3c_i2c4_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_IIC4, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_IIC4),
+};
+
+struct platform_device s3c_device_i2c4 = {
+	.name		= "s3c2440-i2c",
+	.id		= 4,
+	.num_resources	= ARRAY_SIZE(s3c_i2c4_resource),
+	.resource	= s3c_i2c4_resource,
+};
+
+void __init s3c_i2c4_set_platdata(struct s3c2410_platform_i2c *pd)
+{
+	struct s3c2410_platform_i2c *npd;
+
+	if (!pd) {
+		pd = &default_i2c_data;
+		pd->bus_num = 4;
+	}
+
+	npd = s3c_set_platdata(pd, sizeof(struct s3c2410_platform_i2c),
+			       &s3c_device_i2c4);
+
+	if (!npd->cfg_gpio)
+		npd->cfg_gpio = s3c_i2c4_cfg_gpio;
+}
+#endif /*CONFIG_S3C_DEV_I2C4 */
+
+#ifdef CONFIG_S3C_DEV_I2C5
+static struct resource s3c_i2c5_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_IIC5, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_IIC5),
+};
+
+struct platform_device s3c_device_i2c5 = {
+	.name		= "s3c2440-i2c",
+	.id		= 5,
+	.num_resources	= ARRAY_SIZE(s3c_i2c5_resource),
+	.resource	= s3c_i2c5_resource,
+};
+
+void __init s3c_i2c5_set_platdata(struct s3c2410_platform_i2c *pd)
+{
+	struct s3c2410_platform_i2c *npd;
+
+	if (!pd) {
+		pd = &default_i2c_data;
+		pd->bus_num = 5;
+	}
+
+	npd = s3c_set_platdata(pd, sizeof(struct s3c2410_platform_i2c),
+			       &s3c_device_i2c5);
+
+	if (!npd->cfg_gpio)
+		npd->cfg_gpio = s3c_i2c5_cfg_gpio;
+}
+#endif /*CONFIG_S3C_DEV_I2C5 */
+
+#ifdef CONFIG_S3C_DEV_I2C6
+static struct resource s3c_i2c6_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_IIC6, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_IIC6),
+};
+
+struct platform_device s3c_device_i2c6 = {
+	.name		= "s3c2440-i2c",
+	.id		= 6,
+	.num_resources	= ARRAY_SIZE(s3c_i2c6_resource),
+	.resource	= s3c_i2c6_resource,
+};
+
+void __init s3c_i2c6_set_platdata(struct s3c2410_platform_i2c *pd)
+{
+	struct s3c2410_platform_i2c *npd;
+
+	if (!pd) {
+		pd = &default_i2c_data;
+		pd->bus_num = 6;
+	}
+
+	npd = s3c_set_platdata(pd, sizeof(struct s3c2410_platform_i2c),
+			       &s3c_device_i2c6);
+
+	if (!npd->cfg_gpio)
+		npd->cfg_gpio = s3c_i2c6_cfg_gpio;
+}
+#endif /* CONFIG_S3C_DEV_I2C6 */
+
+#ifdef CONFIG_S3C_DEV_I2C7
+static struct resource s3c_i2c7_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_IIC7, SZ_4K),
+	[1] = DEFINE_RES_IRQ(IRQ_IIC7),
+};
+
+struct platform_device s3c_device_i2c7 = {
+	.name		= "s3c2440-i2c",
+	.id		= 7,
+	.num_resources	= ARRAY_SIZE(s3c_i2c7_resource),
+	.resource	= s3c_i2c7_resource,
+};
+
+void __init s3c_i2c7_set_platdata(struct s3c2410_platform_i2c *pd)
+{
+	struct s3c2410_platform_i2c *npd;
+
+	if (!pd) {
+		pd = &default_i2c_data;
+		pd->bus_num = 7;
+	}
+
+	npd = s3c_set_platdata(pd, sizeof(struct s3c2410_platform_i2c),
+			       &s3c_device_i2c7);
+
+	if (!npd->cfg_gpio)
+		npd->cfg_gpio = s3c_i2c7_cfg_gpio;
+}
+#endif /* CONFIG_S3C_DEV_I2C7 */
+
+/* I2S */
+
+#ifdef CONFIG_PLAT_S3C24XX
+static struct resource s3c_iis_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C24XX_PA_IIS, S3C24XX_SZ_IIS),
+};
+
+struct platform_device s3c_device_iis = {
+	.name		= "s3c24xx-iis",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_iis_resource),
+	.resource	= s3c_iis_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	}
+};
+#endif /* CONFIG_PLAT_S3C24XX */
+
+/* IDE CFCON */
+
+#ifdef CONFIG_SAMSUNG_DEV_IDE
+static struct resource s3c_cfcon_resource[] = {
+	[0] = DEFINE_RES_MEM(SAMSUNG_PA_CFCON, SZ_16K),
+	[1] = DEFINE_RES_IRQ(IRQ_CFCON),
+};
+
+struct platform_device s3c_device_cfcon = {
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(s3c_cfcon_resource),
+	.resource	= s3c_cfcon_resource,
+};
+
+void __init s3c_ide_set_platdata(struct s3c_ide_platdata *pdata)
+{
+	s3c_set_platdata(pdata, sizeof(struct s3c_ide_platdata),
+			 &s3c_device_cfcon);
+}
+#endif /* CONFIG_SAMSUNG_DEV_IDE */
+
+/* KEYPAD */
+
+#ifdef CONFIG_SAMSUNG_DEV_KEYPAD
+static struct resource samsung_keypad_resources[] = {
+	[0] = DEFINE_RES_MEM(SAMSUNG_PA_KEYPAD, SZ_32),
+	[1] = DEFINE_RES_IRQ(IRQ_KEYPAD),
+};
+
+struct platform_device samsung_device_keypad = {
+	.name		= "samsung-keypad",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(samsung_keypad_resources),
+	.resource	= samsung_keypad_resources,
+};
+
+void __init samsung_keypad_set_platdata(struct samsung_keypad_platdata *pd)
+{
+	struct samsung_keypad_platdata *npd;
+
+	npd = s3c_set_platdata(pd, sizeof(struct samsung_keypad_platdata),
+			&samsung_device_keypad);
+
+	if (!npd->cfg_gpio)
+		npd->cfg_gpio = samsung_keypad_cfg_gpio;
+}
+#endif /* CONFIG_SAMSUNG_DEV_KEYPAD */
+
+/* LCD Controller */
+
+#ifdef CONFIG_PLAT_S3C24XX
+static struct resource s3c_lcd_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C24XX_PA_LCD, S3C24XX_SZ_LCD),
+	[1] = DEFINE_RES_IRQ(IRQ_LCD),
+};
+
+struct platform_device s3c_device_lcd = {
+	.name		= "s3c2410-lcd",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_lcd_resource),
+	.resource	= s3c_lcd_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	}
+};
+
+void __init s3c24xx_fb_set_platdata(struct s3c2410fb_mach_info *pd)
+{
+	struct s3c2410fb_mach_info *npd;
+
+	npd = s3c_set_platdata(pd, sizeof(*npd), &s3c_device_lcd);
+	if (npd) {
+		npd->displays = kmemdup(pd->displays,
+			sizeof(struct s3c2410fb_display) * npd->num_displays,
+			GFP_KERNEL);
+		if (!npd->displays)
+			printk(KERN_ERR "no memory for LCD display data\n");
+	} else {
+		printk(KERN_ERR "no memory for LCD platform data\n");
+	}
+}
+#endif /* CONFIG_PLAT_S3C24XX */
+
+/* NAND */
+
+#ifdef CONFIG_S3C_DEV_NAND
+static struct resource s3c_nand_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_NAND, SZ_1M),
+};
+
+struct platform_device s3c_device_nand = {
+	.name		= "s3c2410-nand",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_nand_resource),
+	.resource	= s3c_nand_resource,
+};
+
+/*
+ * s3c_nand_copy_set() - copy nand set data
+ * @set: The new structure, directly copied from the old.
+ *
+ * Copy all the fields from the NAND set field from what is probably __initdata
+ * to new kernel memory. The code returns 0 if the copy happened correctly or
+ * an error code for the calling function to display.
+ *
+ * Note, we currently do not try and look to see if we've already copied the
+ * data in a previous set.
+ */
+static int __init s3c_nand_copy_set(struct s3c2410_nand_set *set)
+{
+	void *ptr;
+	int size;
+
+	size = sizeof(struct mtd_partition) * set->nr_partitions;
+	if (size) {
+		ptr = kmemdup(set->partitions, size, GFP_KERNEL);
+		set->partitions = ptr;
+
+		if (!ptr)
+			return -ENOMEM;
+	}
+
+	if (set->nr_map && set->nr_chips) {
+		size = sizeof(int) * set->nr_chips;
+		ptr = kmemdup(set->nr_map, size, GFP_KERNEL);
+		set->nr_map = ptr;
+
+		if (!ptr)
+			return -ENOMEM;
+	}
+
+	if (set->ecc_layout) {
+		ptr = kmemdup(set->ecc_layout,
+			      sizeof(struct nand_ecclayout), GFP_KERNEL);
+		set->ecc_layout = ptr;
+
+		if (!ptr)
+			return -ENOMEM;
+	}
+
+	return 0;
+}
+
+void __init s3c_nand_set_platdata(struct s3c2410_platform_nand *nand)
+{
+	struct s3c2410_platform_nand *npd;
+	int size;
+	int ret;
+
+	/* note, if we get a failure in allocation, we simply drop out of the
+	 * function. If there is so little memory available at initialisation
+	 * time then there is little chance the system is going to run.
+	 */
+
+	npd = s3c_set_platdata(nand, sizeof(struct s3c2410_platform_nand),
+				&s3c_device_nand);
+	if (!npd)
+		return;
+
+	/* now see if we need to copy any of the nand set data */
+
+	size = sizeof(struct s3c2410_nand_set) * npd->nr_sets;
+	if (size) {
+		struct s3c2410_nand_set *from = npd->sets;
+		struct s3c2410_nand_set *to;
+		int i;
+
+		to = kmemdup(from, size, GFP_KERNEL);
+		npd->sets = to;	/* set, even if we failed */
+
+		if (!to) {
+			printk(KERN_ERR "%s: no memory for sets\n", __func__);
+			return;
+		}
+
+		for (i = 0; i < npd->nr_sets; i++) {
+			ret = s3c_nand_copy_set(to);
+			if (ret) {
+				printk(KERN_ERR "%s: failed to copy set %d\n",
+				__func__, i);
+				return;
+			}
+			to++;
+		}
+	}
+}
+#endif /* CONFIG_S3C_DEV_NAND */
+
+/* ONENAND */
+
+#ifdef CONFIG_S3C_DEV_ONENAND
+static struct resource s3c_onenand_resources[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_ONENAND, SZ_1K),
+	[1] = DEFINE_RES_MEM(S3C_PA_ONENAND_BUF, S3C_SZ_ONENAND_BUF),
+	[2] = DEFINE_RES_IRQ(IRQ_ONENAND),
+};
+
+struct platform_device s3c_device_onenand = {
+	.name		= "samsung-onenand",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(s3c_onenand_resources),
+	.resource	= s3c_onenand_resources,
+};
+#endif /* CONFIG_S3C_DEV_ONENAND */
+
+#ifdef CONFIG_S3C64XX_DEV_ONENAND1
+static struct resource s3c64xx_onenand1_resources[] = {
+	[0] = DEFINE_RES_MEM(S3C64XX_PA_ONENAND1, SZ_1K),
+	[1] = DEFINE_RES_MEM(S3C64XX_PA_ONENAND1_BUF, S3C64XX_SZ_ONENAND1_BUF),
+	[2] = DEFINE_RES_IRQ(IRQ_ONENAND1),
+};
+
+struct platform_device s3c64xx_device_onenand1 = {
+	.name		= "samsung-onenand",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(s3c64xx_onenand1_resources),
+	.resource	= s3c64xx_onenand1_resources,
+};
+
+void __init s3c64xx_onenand1_set_platdata(struct onenand_platform_data *pdata)
+{
+	s3c_set_platdata(pdata, sizeof(struct onenand_platform_data),
+			 &s3c64xx_device_onenand1);
+}
+#endif /* CONFIG_S3C64XX_DEV_ONENAND1 */
+
+/* PWM Timer */
+
+#ifdef CONFIG_SAMSUNG_DEV_PWM
+static struct resource samsung_pwm_resource[] = {
+	DEFINE_RES_MEM(SAMSUNG_PA_TIMER, SZ_4K),
+};
+
+struct platform_device samsung_device_pwm = {
+	.name		= "samsung-pwm",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(samsung_pwm_resource),
+	.resource	= samsung_pwm_resource,
+};
+
+void __init samsung_pwm_set_platdata(struct samsung_pwm_variant *pd)
+{
+	samsung_device_pwm.dev.platform_data = pd;
+}
+#endif /* CONFIG_SAMSUNG_DEV_PWM */
+
+/* RTC */
+
+#ifdef CONFIG_PLAT_S3C24XX
+static struct resource s3c_rtc_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C24XX_PA_RTC, SZ_256),
+	[1] = DEFINE_RES_IRQ(IRQ_RTC),
+	[2] = DEFINE_RES_IRQ(IRQ_TICK),
+};
+
+struct platform_device s3c_device_rtc = {
+	.name		= "s3c2410-rtc",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_rtc_resource),
+	.resource	= s3c_rtc_resource,
+};
+#endif /* CONFIG_PLAT_S3C24XX */
+
+#ifdef CONFIG_S3C_DEV_RTC
+static struct resource s3c_rtc_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_RTC, SZ_256),
+	[1] = DEFINE_RES_IRQ(IRQ_RTC_ALARM),
+	[2] = DEFINE_RES_IRQ(IRQ_RTC_TIC),
+};
+
+struct platform_device s3c_device_rtc = {
+	.name		= "s3c64xx-rtc",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_rtc_resource),
+	.resource	= s3c_rtc_resource,
+};
+#endif /* CONFIG_S3C_DEV_RTC */
+
+/* SDI */
+
+#ifdef CONFIG_PLAT_S3C24XX
+static struct resource s3c_sdi_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C24XX_PA_SDI, S3C24XX_SZ_SDI),
+	[1] = DEFINE_RES_IRQ(IRQ_SDI),
+};
+
+struct platform_device s3c_device_sdi = {
+	.name		= "s3c2410-sdi",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_sdi_resource),
+	.resource	= s3c_sdi_resource,
+};
+
+void __init s3c24xx_mci_set_platdata(struct s3c24xx_mci_pdata *pdata)
+{
+	s3c_set_platdata(pdata, sizeof(struct s3c24xx_mci_pdata),
+			 &s3c_device_sdi);
+}
+#endif /* CONFIG_PLAT_S3C24XX */
+
+/* SPI */
+
+#ifdef CONFIG_PLAT_S3C24XX
+static struct resource s3c_spi0_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C24XX_PA_SPI, SZ_32),
+	[1] = DEFINE_RES_IRQ(IRQ_SPI0),
+};
+
+struct platform_device s3c_device_spi0 = {
+	.name		= "s3c2410-spi",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(s3c_spi0_resource),
+	.resource	= s3c_spi0_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	}
+};
+
+static struct resource s3c_spi1_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C24XX_PA_SPI1, SZ_32),
+	[1] = DEFINE_RES_IRQ(IRQ_SPI1),
+};
+
+struct platform_device s3c_device_spi1 = {
+	.name		= "s3c2410-spi",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(s3c_spi1_resource),
+	.resource	= s3c_spi1_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	}
+};
+#endif /* CONFIG_PLAT_S3C24XX */
+
+/* Touchscreen */
+
+#ifdef CONFIG_PLAT_S3C24XX
+static struct resource s3c_ts_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C24XX_PA_ADC, S3C24XX_SZ_ADC),
+	[1] = DEFINE_RES_IRQ(IRQ_TC),
+};
+
+struct platform_device s3c_device_ts = {
+	.name		= "s3c2410-ts",
+	.id		= -1,
+	.dev.parent	= &s3c_device_adc.dev,
+	.num_resources	= ARRAY_SIZE(s3c_ts_resource),
+	.resource	= s3c_ts_resource,
+};
+
+void __init s3c24xx_ts_set_platdata(struct s3c2410_ts_mach_info *hard_s3c2410ts_info)
+{
+	s3c_set_platdata(hard_s3c2410ts_info,
+			 sizeof(struct s3c2410_ts_mach_info), &s3c_device_ts);
+}
+#endif /* CONFIG_PLAT_S3C24XX */
+
+#ifdef CONFIG_SAMSUNG_DEV_TS
+static struct resource s3c_ts_resource[] = {
+	[0] = DEFINE_RES_MEM(SAMSUNG_PA_ADC, SZ_256),
+	[1] = DEFINE_RES_IRQ(IRQ_TC),
+};
+
+static struct s3c2410_ts_mach_info default_ts_data __initdata = {
+	.delay			= 10000,
+	.presc			= 49,
+	.oversampling_shift	= 2,
+};
+
+struct platform_device s3c_device_ts = {
+	.name		= "s3c64xx-ts",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_ts_resource),
+	.resource	= s3c_ts_resource,
+};
+
+void __init s3c24xx_ts_set_platdata(struct s3c2410_ts_mach_info *pd)
+{
+	if (!pd)
+		pd = &default_ts_data;
+
+	s3c_set_platdata(pd, sizeof(struct s3c2410_ts_mach_info),
+			 &s3c_device_ts);
+}
+#endif /* CONFIG_SAMSUNG_DEV_TS */
+
+/* USB */
+
+#ifdef CONFIG_S3C_DEV_USB_HOST
+static struct resource s3c_usb_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_USBHOST, SZ_256),
+	[1] = DEFINE_RES_IRQ(IRQ_USBH),
+};
+
+struct platform_device s3c_device_ohci = {
+	.name		= "s3c2410-ohci",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_usb_resource),
+	.resource	= s3c_usb_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	}
+};
+
+/*
+ * s3c_ohci_set_platdata - initialise OHCI device platform data
+ * @info: The platform data.
+ *
+ * This call copies the @info passed in and sets the device .platform_data
+ * field to that copy. The @info is copied so that the original can be marked
+ * __initdata.
+ */
+
+void __init s3c_ohci_set_platdata(struct s3c2410_hcd_info *info)
+{
+	s3c_set_platdata(info, sizeof(struct s3c2410_hcd_info),
+			 &s3c_device_ohci);
+}
+#endif /* CONFIG_S3C_DEV_USB_HOST */
+
+/* USB Device (Gadget) */
+
+#ifdef CONFIG_PLAT_S3C24XX
+static struct resource s3c_usbgadget_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C24XX_PA_USBDEV, S3C24XX_SZ_USBDEV),
+	[1] = DEFINE_RES_IRQ(IRQ_USBD),
+};
+
+struct platform_device s3c_device_usbgadget = {
+	.name		= "s3c2410-usbgadget",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_usbgadget_resource),
+	.resource	= s3c_usbgadget_resource,
+};
+
+void __init s3c24xx_udc_set_platdata(struct s3c2410_udc_mach_info *pd)
+{
+	s3c_set_platdata(pd, sizeof(*pd), &s3c_device_usbgadget);
+}
+#endif /* CONFIG_PLAT_S3C24XX */
+
+/* USB HSOTG */
+
+#ifdef CONFIG_S3C_DEV_USB_HSOTG
+static struct resource s3c_usb_hsotg_resources[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_USB_HSOTG, SZ_128K),
+	[1] = DEFINE_RES_IRQ(IRQ_OTG),
+};
+
+struct platform_device s3c_device_usb_hsotg = {
+	.name		= "s3c-hsotg",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_usb_hsotg_resources),
+	.resource	= s3c_usb_hsotg_resources,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+void __init s3c_hsotg_set_platdata(struct s3c_hsotg_plat *pd)
+{
+	struct s3c_hsotg_plat *npd;
+
+	npd = s3c_set_platdata(pd, sizeof(struct s3c_hsotg_plat),
+			&s3c_device_usb_hsotg);
+
+	if (!npd->phy_init)
+		npd->phy_init = s5p_usb_phy_init;
+	if (!npd->phy_exit)
+		npd->phy_exit = s5p_usb_phy_exit;
+}
+#endif /* CONFIG_S3C_DEV_USB_HSOTG */
+
+/* USB High Spped 2.0 Device (Gadget) */
+
+#ifdef CONFIG_PLAT_S3C24XX
+static struct resource s3c_hsudc_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C2416_PA_HSUDC, S3C2416_SZ_HSUDC),
+	[1] = DEFINE_RES_IRQ(IRQ_USBD),
+};
+
+struct platform_device s3c_device_usb_hsudc = {
+	.name		= "s3c-hsudc",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_hsudc_resource),
+	.resource	= s3c_hsudc_resource,
+	.dev		= {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+void __init s3c24xx_hsudc_set_platdata(struct s3c24xx_hsudc_platdata *pd)
+{
+	s3c_set_platdata(pd, sizeof(*pd), &s3c_device_usb_hsudc);
+}
+#endif /* CONFIG_PLAT_S3C24XX */
+
+/* WDT */
+
+#ifdef CONFIG_S3C_DEV_WDT
+static struct resource s3c_wdt_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_WDT, SZ_1K),
+	[1] = DEFINE_RES_IRQ(IRQ_WDT),
+};
+
+struct platform_device s3c_device_wdt = {
+	.name		= "s3c2410-wdt",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(s3c_wdt_resource),
+	.resource	= s3c_wdt_resource,
+};
+#endif /* CONFIG_S3C_DEV_WDT */
+
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+static struct resource s3c64xx_spi0_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_SPI0, SZ_256),
+	[1] = DEFINE_RES_DMA(DMACH_SPI0_TX),
+	[2] = DEFINE_RES_DMA(DMACH_SPI0_RX),
+	[3] = DEFINE_RES_IRQ(IRQ_SPI0),
+};
+
+struct platform_device s3c64xx_device_spi0 = {
+	.name		= "s3c6410-spi",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(s3c64xx_spi0_resource),
+	.resource	= s3c64xx_spi0_resource,
+	.dev = {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+void __init s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs)
+{
+	struct s3c64xx_spi_info pd;
+
+	/* Reject invalid configuration */
+	if (!num_cs || src_clk_nr < 0) {
+		pr_err("%s: Invalid SPI configuration\n", __func__);
+		return;
+	}
+
+	pd.num_cs = num_cs;
+	pd.src_clk_nr = src_clk_nr;
+	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi0_cfg_gpio;
+#if defined(CONFIG_PL330_DMA)
+	pd.filter = pl330_filter;
+#elif defined(CONFIG_S3C64XX_PL080)
+	pd.filter = pl08x_filter_id;
+#elif defined(CONFIG_S3C24XX_DMAC)
+	pd.filter = s3c24xx_dma_filter;
+#endif
+
+	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi0);
+}
+#endif /* CONFIG_S3C64XX_DEV_SPI0 */
+
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+static struct resource s3c64xx_spi1_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_SPI1, SZ_256),
+	[1] = DEFINE_RES_DMA(DMACH_SPI1_TX),
+	[2] = DEFINE_RES_DMA(DMACH_SPI1_RX),
+	[3] = DEFINE_RES_IRQ(IRQ_SPI1),
+};
+
+struct platform_device s3c64xx_device_spi1 = {
+	.name		= "s3c6410-spi",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(s3c64xx_spi1_resource),
+	.resource	= s3c64xx_spi1_resource,
+	.dev = {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+void __init s3c64xx_spi1_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs)
+{
+	struct s3c64xx_spi_info pd;
+
+	/* Reject invalid configuration */
+	if (!num_cs || src_clk_nr < 0) {
+		pr_err("%s: Invalid SPI configuration\n", __func__);
+		return;
+	}
+
+	pd.num_cs = num_cs;
+	pd.src_clk_nr = src_clk_nr;
+	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi1_cfg_gpio;
+#if defined(CONFIG_PL330_DMA)
+	pd.filter = pl330_filter;
+#elif defined(CONFIG_S3C64XX_PL080)
+	pd.filter = pl08x_filter_id;
+#endif
+
+	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi1);
+}
+#endif /* CONFIG_S3C64XX_DEV_SPI1 */
+
+#ifdef CONFIG_S3C64XX_DEV_SPI2
+static struct resource s3c64xx_spi2_resource[] = {
+	[0] = DEFINE_RES_MEM(S3C_PA_SPI2, SZ_256),
+	[1] = DEFINE_RES_DMA(DMACH_SPI2_TX),
+	[2] = DEFINE_RES_DMA(DMACH_SPI2_RX),
+	[3] = DEFINE_RES_IRQ(IRQ_SPI2),
+};
+
+struct platform_device s3c64xx_device_spi2 = {
+	.name		= "s3c6410-spi",
+	.id		= 2,
+	.num_resources	= ARRAY_SIZE(s3c64xx_spi2_resource),
+	.resource	= s3c64xx_spi2_resource,
+	.dev = {
+		.dma_mask		= &samsung_device_dma_mask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+};
+
+void __init s3c64xx_spi2_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs)
+{
+	struct s3c64xx_spi_info pd;
+
+	/* Reject invalid configuration */
+	if (!num_cs || src_clk_nr < 0) {
+		pr_err("%s: Invalid SPI configuration\n", __func__);
+		return;
+	}
+
+	pd.num_cs = num_cs;
+	pd.src_clk_nr = src_clk_nr;
+	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi2_cfg_gpio;
+#if defined(CONFIG_PL330_DMA)
+	pd.filter = pl330_filter;
+#elif defined(CONFIG_S3C64XX_PL080)
+	pd.filter = pl08x_filter_id;
+#endif
+
+	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi2);
+}
+#endif /* CONFIG_S3C64XX_DEV_SPI2 */
diff --git a/arch/arm/plat-samsung/include/plat/adc-core.h b/arch/arm/plat-samsung/include/plat/adc-core.h
new file mode 100644
index 000000000..a927bee55
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/adc-core.h
@@ -0,0 +1,28 @@
+/* linux/arch/arm/plat-samsung/include/plat/adc-core.h
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com/
+ *
+ * Samsung ADC Controller core functions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_ADC_CORE_H
+#define __ASM_PLAT_ADC_CORE_H __FILE__
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void s3c_adc_setname(char *name)
+{
+#if defined(CONFIG_SAMSUNG_DEV_ADC) || defined(CONFIG_PLAT_S3C24XX)
+	s3c_device_adc.name = name;
+#endif
+}
+
+#endif /* __ASM_PLAT_ADC_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/adc.h b/arch/arm/plat-samsung/include/plat/adc.h
new file mode 100644
index 000000000..2fc893155
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/adc.h
@@ -0,0 +1,36 @@
+/* arch/arm/plat-samsung/include/plat/adc.h
+ *
+ * Copyright (c) 2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/	
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C ADC driver information
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_ADC_H
+#define __ASM_PLAT_ADC_H __FILE__
+
+struct s3c_adc_client;
+struct platform_device;
+
+extern int s3c_adc_start(struct s3c_adc_client *client,
+			 unsigned int channel, unsigned int nr_samples);
+
+extern int s3c_adc_read(struct s3c_adc_client *client, unsigned int ch);
+
+extern struct s3c_adc_client *
+	s3c_adc_register(struct platform_device *pdev,
+			 void (*select)(struct s3c_adc_client *client,
+					unsigned selected),
+			 void (*conv)(struct s3c_adc_client *client,
+				      unsigned d0, unsigned d1,
+				      unsigned *samples_left),
+			 unsigned int is_ts);
+
+extern void s3c_adc_release(struct s3c_adc_client *client);
+
+#endif /* __ASM_PLAT_ADC_H */
diff --git a/arch/arm/plat-samsung/include/plat/ata-core.h b/arch/arm/plat-samsung/include/plat/ata-core.h
new file mode 100644
index 000000000..f5a4ec714
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/ata-core.h
@@ -0,0 +1,28 @@
+/* linux/arch/arm/plat-samsung/include/plat/ata-core.h
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Samsung CF-ATA Controller core functions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_ATA_CORE_H
+#define __ASM_PLAT_ATA_CORE_H __FILE__
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+*/
+
+/* re-define device name depending on support. */
+static inline void s3c_cfcon_setname(char *name)
+{
+#ifdef CONFIG_SAMSUNG_DEV_IDE
+	s3c_device_cfcon.name = name;
+#endif
+}
+
+#endif /* __ASM_PLAT_ATA_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/backlight.h b/arch/arm/plat-samsung/include/plat/backlight.h
new file mode 100644
index 000000000..ad530c78f
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/backlight.h
@@ -0,0 +1,26 @@
+/* linux/arch/arm/plat-samsung/include/plat/backlight.h
+ *
+ * Copyright (c) 2011 Samsung Electronics Co., Ltd.
+ *              http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_PLAT_BACKLIGHT_H
+#define __ASM_PLAT_BACKLIGHT_H __FILE__
+
+/* samsung_bl_gpio_info - GPIO info for PWM Backlight control
+ * @no:		GPIO number for PWM timer out
+ * @func:	Special function of GPIO line for PWM timer
+ */
+struct samsung_bl_gpio_info {
+	int no;
+	int func;
+};
+
+extern void __init samsung_bl_set(struct samsung_bl_gpio_info *gpio_info,
+	struct platform_pwm_backlight_data *bl_data);
+
+#endif /* __ASM_PLAT_BACKLIGHT_H */
diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq-core.h b/arch/arm/plat-samsung/include/plat/cpu-freq-core.h
new file mode 100644
index 000000000..317c52303
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/cpu-freq-core.h
@@ -0,0 +1,291 @@
+/* arch/arm/plat-samsung/include/plat/cpu-freq-core.h
+ *
+ * Copyright (c) 2006-2009 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C CPU frequency scaling support - core support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <plat/cpu-freq.h>
+
+struct seq_file;
+
+#define MAX_BANKS (8)
+#define S3C2412_MAX_IO	(8)
+
+/**
+ * struct s3c2410_iobank_timing - IO bank timings for S3C2410 style timings
+ * @bankcon: The cached version of settings in this structure.
+ * @tacp:
+ * @tacs: Time from address valid to nCS asserted.
+ * @tcos: Time from nCS asserted to nOE or nWE asserted.
+ * @tacc: Time that nOE or nWE is asserted.
+ * @tcoh: Time nCS is held after nOE or nWE are released.
+ * @tcah: Time address is held for after
+ * @nwait_en: Whether nWAIT is enabled for this bank.
+ *
+ * This structure represents the IO timings for a S3C2410 style IO bank
+ * used by the CPU frequency support if it needs to change the settings
+ * of the IO.
+ */
+struct s3c2410_iobank_timing {
+	unsigned long	bankcon;
+	unsigned int	tacp;
+	unsigned int	tacs;
+	unsigned int	tcos;
+	unsigned int	tacc;
+	unsigned int	tcoh;		/* nCS hold afrer nOE/nWE */
+	unsigned int	tcah;		/* Address hold after nCS */
+	unsigned char	nwait_en;	/* nWait enabled for bank. */
+};
+
+/**
+ * struct s3c2412_iobank_timing - io timings for PL092 (S3C2412) style IO
+ * @idcy: The idle cycle time between transactions.
+ * @wstrd: nCS release to end of read cycle.
+ * @wstwr: nCS release to end of write cycle.
+ * @wstoen: nCS assertion to nOE assertion time.
+ * @wstwen: nCS assertion to nWE assertion time.
+ * @wstbrd: Burst ready delay.
+ * @smbidcyr: Register cache for smbidcyr value.
+ * @smbwstrd: Register cache for smbwstrd value.
+ * @smbwstwr: Register cache for smbwstwr value.
+ * @smbwstoen: Register cache for smbwstoen value.
+ * @smbwstwen: Register cache for smbwstwen value.
+ * @smbwstbrd: Register cache for smbwstbrd value.
+ *
+ * Timing information for a IO bank on an S3C2412 or similar system which
+ * uses a PL093 block.
+ */
+struct s3c2412_iobank_timing {
+	unsigned int	idcy;
+	unsigned int	wstrd;
+	unsigned int	wstwr;
+	unsigned int	wstoen;
+	unsigned int	wstwen;
+	unsigned int	wstbrd;
+
+	/* register cache */
+	unsigned char	smbidcyr;
+	unsigned char	smbwstrd;
+	unsigned char	smbwstwr;
+	unsigned char	smbwstoen;
+	unsigned char	smbwstwen;
+	unsigned char	smbwstbrd;
+};
+
+union s3c_iobank {
+	struct s3c2410_iobank_timing	*io_2410;
+	struct s3c2412_iobank_timing	*io_2412;
+};
+
+/**
+ * struct s3c_iotimings - Chip IO timings holder
+ * @bank: The timings for each IO bank.
+ */
+struct s3c_iotimings {
+	union s3c_iobank	bank[MAX_BANKS];
+};
+
+/**
+ * struct s3c_plltab - PLL table information.
+ * @vals: List of PLL values.
+ * @size: Size of the PLL table @vals.
+ */
+struct s3c_plltab {
+	struct s3c_pllval	*vals;
+	int			 size;
+};
+
+/**
+ * struct s3c_cpufreq_config - current cpu frequency configuration
+ * @freq: The current settings for the core clocks.
+ * @max: Maxium settings, derived from core, board and user settings.
+ * @pll: The PLL table entry for the current PLL settings.
+ * @divs: The divisor settings for the core clocks.
+ * @info: The current core driver information.
+ * @board: The information for the board we are running on.
+ * @lock_pll: Set if the PLL settings cannot be changed.
+ *
+ * This is for the core drivers that need to know information about
+ * the current settings and values. It should not be needed by any
+ * device drivers.
+*/
+struct s3c_cpufreq_config {
+	struct s3c_freq		freq;
+	struct s3c_freq		max;
+	struct clk		*mpll;
+	struct cpufreq_frequency_table pll;
+	struct s3c_clkdivs	divs;
+	struct s3c_cpufreq_info *info;	/* for core, not drivers */
+	struct s3c_cpufreq_board *board;
+
+	unsigned int	lock_pll:1;
+};
+
+/**
+ * struct s3c_cpufreq_info - Information for the CPU frequency driver.
+ * @name: The name of this implementation.
+ * @max: The maximum frequencies for the system.
+ * @latency: Transition latency to give to cpufreq.
+ * @locktime_m: The lock-time in uS for the MPLL.
+ * @locktime_u: The lock-time in uS for the UPLL.
+ * @locttime_bits: The number of bits each LOCKTIME field.
+ * @need_pll: Set if this driver needs to change the PLL values to achieve
+ *	any frequency changes. This is really only need by devices like the
+ *	S3C2410 where there is no or limited divider between the PLL and the
+ *	ARMCLK.
+ * @get_iotiming: Get the current IO timing data, mainly for use at start.
+ * @set_iotiming: Update the IO timings from the cached copies calculated
+ *	from the @calc_iotiming entry when changing the frequency.
+ * @calc_iotiming: Calculate and update the cached copies of the IO timings
+ *	from the newly calculated frequencies.
+ * @calc_freqtable: Calculate (fill in) the given frequency table from the
+ *	current frequency configuration. If the table passed in is NULL,
+ *	then the return is the number of elements to be filled for allocation
+ *	of the table.
+ * @set_refresh: Set the memory refresh configuration.
+ * @set_fvco: Set the PLL frequencies.
+ * @set_divs: Update the clock divisors.
+ * @calc_divs: Calculate the clock divisors.
+ */
+struct s3c_cpufreq_info {
+	const char		*name;
+	struct s3c_freq		max;
+
+	unsigned int		latency;
+
+	unsigned int		locktime_m;
+	unsigned int		locktime_u;
+	unsigned char		locktime_bits;
+
+	unsigned int		need_pll:1;
+
+	/* driver routines */
+
+	int		(*get_iotiming)(struct s3c_cpufreq_config *cfg,
+					struct s3c_iotimings *timings);
+
+	void		(*set_iotiming)(struct s3c_cpufreq_config *cfg,
+					struct s3c_iotimings *timings);
+
+	int		(*calc_iotiming)(struct s3c_cpufreq_config *cfg,
+					 struct s3c_iotimings *timings);
+
+	int		(*calc_freqtable)(struct s3c_cpufreq_config *cfg,
+					  struct cpufreq_frequency_table *t,
+					  size_t table_size);
+
+	void		(*debug_io_show)(struct seq_file *seq,
+					 struct s3c_cpufreq_config *cfg,
+					 union s3c_iobank *iob);
+
+	void		(*set_refresh)(struct s3c_cpufreq_config *cfg);
+	void		(*set_fvco)(struct s3c_cpufreq_config *cfg);
+	void		(*set_divs)(struct s3c_cpufreq_config *cfg);
+	int		(*calc_divs)(struct s3c_cpufreq_config *cfg);
+};
+
+extern int s3c_cpufreq_register(struct s3c_cpufreq_info *info);
+
+extern int s3c_plltab_register(struct cpufreq_frequency_table *plls,
+			       unsigned int plls_no);
+
+/* exports and utilities for debugfs */
+extern struct s3c_cpufreq_config *s3c_cpufreq_getconfig(void);
+extern struct s3c_iotimings *s3c_cpufreq_getiotimings(void);
+
+#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_DEBUGFS
+#define s3c_cpufreq_debugfs_call(x) x
+#else
+#define s3c_cpufreq_debugfs_call(x) NULL
+#endif
+
+/* Useful utility functions. */
+
+extern struct clk *s3c_cpufreq_clk_get(struct device *, const char *);
+
+/* S3C2410 and compatible exported functions */
+
+extern void s3c2410_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg);
+extern void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg);
+
+#ifdef CONFIG_S3C2410_IOTIMING
+extern void s3c2410_iotiming_debugfs(struct seq_file *seq,
+				     struct s3c_cpufreq_config *cfg,
+				     union s3c_iobank *iob);
+
+extern int s3c2410_iotiming_calc(struct s3c_cpufreq_config *cfg,
+				 struct s3c_iotimings *iot);
+
+extern int s3c2410_iotiming_get(struct s3c_cpufreq_config *cfg,
+				struct s3c_iotimings *timings);
+
+extern void s3c2410_iotiming_set(struct s3c_cpufreq_config *cfg,
+				 struct s3c_iotimings *iot);
+#else
+#define s3c2410_iotiming_debugfs NULL
+#define s3c2410_iotiming_calc NULL
+#define s3c2410_iotiming_get NULL
+#define s3c2410_iotiming_set NULL
+#endif /* CONFIG_S3C2410_IOTIMING */
+
+/* S3C2412 compatible routines */
+
+#ifdef CONFIG_S3C2412_IOTIMING
+extern void s3c2412_iotiming_debugfs(struct seq_file *seq,
+				     struct s3c_cpufreq_config *cfg,
+				     union s3c_iobank *iob);
+
+extern int s3c2412_iotiming_get(struct s3c_cpufreq_config *cfg,
+				struct s3c_iotimings *timings);
+
+extern int s3c2412_iotiming_calc(struct s3c_cpufreq_config *cfg,
+				 struct s3c_iotimings *iot);
+
+extern void s3c2412_iotiming_set(struct s3c_cpufreq_config *cfg,
+				 struct s3c_iotimings *iot);
+#else
+#define s3c2412_iotiming_debugfs NULL
+#define s3c2412_iotiming_calc NULL
+#define s3c2412_iotiming_get NULL
+#define s3c2412_iotiming_set NULL
+#endif /* CONFIG_S3C2412_IOTIMING */
+
+#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_DEBUG
+#define s3c_freq_dbg(x...) printk(KERN_INFO x)
+#else
+#define s3c_freq_dbg(x...) do { if (0) printk(x); } while (0)
+#endif /* CONFIG_ARM_S3C24XX_CPUFREQ_DEBUG */
+
+#ifdef CONFIG_ARM_S3C24XX_CPUFREQ_IODEBUG
+#define s3c_freq_iodbg(x...) printk(KERN_INFO x)
+#else
+#define s3c_freq_iodbg(x...) do { if (0) printk(x); } while (0)
+#endif /* CONFIG_ARM_S3C24XX_CPUFREQ_IODEBUG */
+
+static inline int s3c_cpufreq_addfreq(struct cpufreq_frequency_table *table,
+				      int index, size_t table_size,
+				      unsigned int freq)
+{
+	if (index < 0)
+		return index;
+
+	if (table) {
+		if (index >= table_size)
+			return -ENOMEM;
+
+		s3c_freq_dbg("%s: { %d = %u kHz }\n",
+			     __func__, index, freq);
+
+		table[index].driver_data = index;
+		table[index].frequency = freq;
+	}
+
+	return index + 1;
+}
diff --git a/arch/arm/plat-samsung/include/plat/cpu-freq.h b/arch/arm/plat-samsung/include/plat/cpu-freq.h
new file mode 100644
index 000000000..85517ab96
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/cpu-freq.h
@@ -0,0 +1,145 @@
+/* arch/arm/plat-samsung/include/plat/cpu-freq.h
+ *
+ * Copyright (c) 2006-2007 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C CPU frequency scaling support - driver and board
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/cpufreq.h>
+
+struct s3c_cpufreq_info;
+struct s3c_cpufreq_board;
+struct s3c_iotimings;
+
+/**
+ * struct s3c_freq - frequency information (mainly for core drivers)
+ * @fclk: The FCLK frequency in Hz.
+ * @armclk: The ARMCLK frequency in Hz.
+ * @hclk_tns: HCLK cycle time in 10ths of nano-seconds.
+ * @hclk: The HCLK frequency in Hz.
+ * @pclk: The PCLK frequency in Hz.
+ *
+ * This contains the frequency information about the current configuration
+ * mainly for the core drivers to ensure we do not end up passing about
+ * a large number of parameters.
+ *
+ * The @hclk_tns field is a useful cache for the parts of the drivers that
+ * need to calculate IO timings and suchlike.
+ */
+struct s3c_freq {
+	unsigned long	fclk;
+	unsigned long	armclk;
+	unsigned long	hclk_tns;	/* in 10ths of ns */
+	unsigned long	hclk;
+	unsigned long	pclk;
+};
+
+/**
+ * struct s3c_cpufreq_freqs - s3c cpufreq notification information.
+ * @freqs: The cpufreq setting information.
+ * @old: The old clock settings.
+ * @new: The new clock settings.
+ * @pll_changing: Set if the PLL is changing.
+ *
+ * Wrapper 'struct cpufreq_freqs' so that any drivers receiving the
+ * notification can use this information that is not provided by just
+ * having the core frequency alone.
+ *
+ * The pll_changing flag is used to indicate if the PLL itself is
+ * being set during this change. This is important as the clocks
+ * will temporarily be set to the XTAL clock during this time, so
+ * drivers may want to close down their output during this time.
+ *
+ * Note, this is not being used by any current drivers and therefore
+ * may be removed in the future.
+ */
+struct s3c_cpufreq_freqs {
+	struct cpufreq_freqs	freqs;
+	struct s3c_freq		old;
+	struct s3c_freq		new;
+
+	unsigned int		pll_changing:1;
+};
+
+#define to_s3c_cpufreq(_cf) container_of(_cf, struct s3c_cpufreq_freqs, freqs)
+
+/**
+ * struct s3c_clkdivs - clock divisor information
+ * @p_divisor: Divisor from FCLK to PCLK.
+ * @h_divisor: Divisor from FCLK to HCLK.
+ * @arm_divisor: Divisor from FCLK to ARMCLK (not all CPUs).
+ * @dvs: Non-zero if using DVS mode for ARMCLK.
+ *
+ * Divisor settings for the core clocks.
+ */
+struct s3c_clkdivs {
+	int		p_divisor;
+	int		h_divisor;
+	int		arm_divisor;
+	unsigned char	dvs;
+};
+
+#define PLLVAL(_m, _p, _s) (((_m) << 12) | ((_p) << 4) | (_s))
+
+/**
+ * struct s3c_pllval - PLL value entry.
+ * @freq: The frequency for this entry in Hz.
+ * @pll_reg: The PLL register setting for this PLL value.
+ */
+struct s3c_pllval {
+	unsigned long		freq;
+	unsigned long		pll_reg;
+};
+
+/**
+ * struct s3c_cpufreq_board - per-board cpu frequency informatin
+ * @refresh: The SDRAM refresh period in nanoseconds.
+ * @auto_io: Set if the IO timing settings should be generated from the
+ *	initialisation time hardware registers.
+ * @need_io: Set if the board has external IO on any of the chipselect
+ *	lines that will require the hardware timing registers to be
+ *	updated on a clock change.
+ * @max: The maxium frequency limits for the system. Any field that
+ *	is left at zero will use the CPU's settings.
+ *
+ * This contains the board specific settings that affect how the CPU
+ * drivers chose settings. These include the memory refresh and IO
+ * timing information.
+ *
+ * Registration depends on the driver being used, the ARMCLK only
+ * implementation does not currently need this but the older style
+ * driver requires this to be available.
+ */
+struct s3c_cpufreq_board {
+	unsigned int	refresh;
+	unsigned int	auto_io:1;	/* automatically init io timings. */
+	unsigned int	need_io:1;	/* set if needs io timing support. */
+
+	/* any non-zero field in here is taken as an upper limit. */
+	struct s3c_freq	max;	/* frequency limits */
+};
+
+/* Things depending on frequency scaling. */
+#ifdef CONFIG_ARM_S3C_CPUFREQ
+#define __init_or_cpufreq
+#else
+#define __init_or_cpufreq __init
+#endif
+
+/* Board functions */
+
+#ifdef CONFIG_ARM_S3C_CPUFREQ
+extern int s3c_cpufreq_setboard(struct s3c_cpufreq_board *board);
+#else
+
+static inline int s3c_cpufreq_setboard(struct s3c_cpufreq_board *board)
+{
+	return 0;
+}
+#endif  /* CONFIG_ARM_S3C_CPUFREQ */
diff --git a/arch/arm/plat-samsung/include/plat/cpu.h b/arch/arm/plat-samsung/include/plat/cpu.h
new file mode 100644
index 000000000..61d14f3a0
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/cpu.h
@@ -0,0 +1,143 @@
+/* linux/arch/arm/plat-samsung/include/plat/cpu.h
+ *
+ * Copyright (c) 2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com/
+ *
+ * Copyright (c) 2004-2005 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Header file for Samsung CPU support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* todo - fix when rmk changes iodescs to use `void __iomem *` */
+
+#ifndef __SAMSUNG_PLAT_CPU_H
+#define __SAMSUNG_PLAT_CPU_H
+
+extern unsigned long samsung_cpu_id;
+
+#define S3C2410_CPU_ID		0x32410000
+#define S3C2410_CPU_MASK	0xFFFFFFFF
+
+#define S3C24XX_CPU_ID		0x32400000
+#define S3C24XX_CPU_MASK	0xFFF00000
+
+#define S3C2412_CPU_ID		0x32412000
+#define S3C2412_CPU_MASK	0xFFFFF000
+
+#define S3C6400_CPU_ID		0x36400000
+#define S3C6410_CPU_ID		0x36410000
+#define S3C64XX_CPU_MASK	0xFFFFF000
+
+#define S5PV210_CPU_ID		0x43110000
+#define S5PV210_CPU_MASK	0xFFFFF000
+
+#define IS_SAMSUNG_CPU(name, id, mask)		\
+static inline int is_samsung_##name(void)	\
+{						\
+	return ((samsung_cpu_id & mask) == (id & mask));	\
+}
+
+IS_SAMSUNG_CPU(s3c2410, S3C2410_CPU_ID, S3C2410_CPU_MASK)
+IS_SAMSUNG_CPU(s3c24xx, S3C24XX_CPU_ID, S3C24XX_CPU_MASK)
+IS_SAMSUNG_CPU(s3c2412, S3C2412_CPU_ID, S3C2412_CPU_MASK)
+IS_SAMSUNG_CPU(s3c6400, S3C6400_CPU_ID, S3C64XX_CPU_MASK)
+IS_SAMSUNG_CPU(s3c6410, S3C6410_CPU_ID, S3C64XX_CPU_MASK)
+
+#if defined(CONFIG_CPU_S3C2410) || defined(CONFIG_CPU_S3C2412) || \
+    defined(CONFIG_CPU_S3C2416) || defined(CONFIG_CPU_S3C2440) || \
+    defined(CONFIG_CPU_S3C2442) || defined(CONFIG_CPU_S3C244X) || \
+    defined(CONFIG_CPU_S3C2443)
+# define soc_is_s3c24xx()	is_samsung_s3c24xx()
+# define soc_is_s3c2410()	is_samsung_s3c2410()
+#else
+# define soc_is_s3c24xx()	0
+# define soc_is_s3c2410()	0
+#endif
+
+#if defined(CONFIG_CPU_S3C2412)
+# define soc_is_s3c2412()	is_samsung_s3c2412()
+#else
+# define soc_is_s3c2412()	0
+#endif
+
+#if defined(CONFIG_CPU_S3C6400) || defined(CONFIG_CPU_S3C6410)
+# define soc_is_s3c6400()	is_samsung_s3c6400()
+# define soc_is_s3c6410()	is_samsung_s3c6410()
+# define soc_is_s3c64xx()	(is_samsung_s3c6400() || is_samsung_s3c6410())
+#else
+# define soc_is_s3c6400()	0
+# define soc_is_s3c6410()	0
+# define soc_is_s3c64xx()	0
+#endif
+
+#define IODESC_ENT(x) { (unsigned long)S3C24XX_VA_##x, __phys_to_pfn(S3C24XX_PA_##x), S3C24XX_SZ_##x, MT_DEVICE }
+
+#ifndef KHZ
+#define KHZ (1000)
+#endif
+
+#ifndef MHZ
+#define MHZ (1000*1000)
+#endif
+
+#define print_mhz(m) ((m) / MHZ), (((m) / 1000) % 1000)
+
+/* forward declaration */
+struct s3c24xx_uart_resources;
+struct platform_device;
+struct s3c2410_uartcfg;
+struct map_desc;
+
+/* per-cpu initialisation function table. */
+
+struct cpu_table {
+	unsigned long	idcode;
+	unsigned long	idmask;
+	void		(*map_io)(void);
+	void		(*init_uarts)(struct s3c2410_uartcfg *cfg, int no);
+	void		(*init_clocks)(int xtal);
+	int		(*init)(void);
+	const char	*name;
+};
+
+extern void s3c_init_cpu(unsigned long idcode,
+			 struct cpu_table *cpus, unsigned int cputab_size);
+
+/* core initialisation functions */
+
+extern void s3c24xx_init_io(struct map_desc *mach_desc, int size);
+
+extern void s3c64xx_init_cpu(void);
+
+extern unsigned int samsung_rev(void);
+
+extern void s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no);
+
+extern void s3c24xx_init_clocks(int xtal);
+
+extern void s3c24xx_init_uartdevs(char *name,
+				  struct s3c24xx_uart_resources *res,
+				  struct s3c2410_uartcfg *cfg, int no);
+
+extern struct syscore_ops s3c2410_pm_syscore_ops;
+extern struct syscore_ops s3c2412_pm_syscore_ops;
+extern struct syscore_ops s3c2416_pm_syscore_ops;
+extern struct syscore_ops s3c244x_pm_syscore_ops;
+
+/* system device subsystems */
+
+extern struct bus_type s3c2410_subsys;
+extern struct bus_type s3c2410a_subsys;
+extern struct bus_type s3c2412_subsys;
+extern struct bus_type s3c2416_subsys;
+extern struct bus_type s3c2440_subsys;
+extern struct bus_type s3c2442_subsys;
+extern struct bus_type s3c2443_subsys;
+extern struct bus_type s3c6410_subsys;
+
+#endif
diff --git a/arch/arm/plat-samsung/include/plat/devs.h b/arch/arm/plat-samsung/include/plat/devs.h
new file mode 100644
index 000000000..e23fed311
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/devs.h
@@ -0,0 +1,100 @@
+/* arch/arm/plat-samsung/include/plat/devs.h
+ *
+ * Copyright (c) 2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Copyright (c) 2004 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ *
+ * Header file for s3c2410 standard platform devices
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __PLAT_DEVS_H
+#define __PLAT_DEVS_H __FILE__
+
+#include <linux/platform_device.h>
+
+struct s3c24xx_uart_resources {
+	struct resource		*resources;
+	unsigned long		 nr_resources;
+};
+
+extern struct s3c24xx_uart_resources s3c2410_uart_resources[];
+extern struct s3c24xx_uart_resources s3c64xx_uart_resources[];
+
+extern struct platform_device *s3c24xx_uart_devs[];
+extern struct platform_device *s3c24xx_uart_src[];
+
+extern struct platform_device s3c64xx_device_ac97;
+extern struct platform_device s3c64xx_device_iis0;
+extern struct platform_device s3c64xx_device_iis1;
+extern struct platform_device s3c64xx_device_iisv4;
+extern struct platform_device s3c64xx_device_onenand1;
+extern struct platform_device s3c64xx_device_pcm0;
+extern struct platform_device s3c64xx_device_pcm1;
+extern struct platform_device s3c64xx_device_spi0;
+extern struct platform_device s3c64xx_device_spi1;
+extern struct platform_device s3c64xx_device_spi2;
+
+extern struct platform_device s3c_device_adc;
+extern struct platform_device s3c_device_cfcon;
+extern struct platform_device s3c_device_fb;
+extern struct platform_device s3c_device_hwmon;
+extern struct platform_device s3c_device_hsmmc0;
+extern struct platform_device s3c_device_hsmmc1;
+extern struct platform_device s3c_device_hsmmc2;
+extern struct platform_device s3c_device_hsmmc3;
+extern struct platform_device s3c_device_i2c0;
+extern struct platform_device s3c_device_i2c1;
+extern struct platform_device s3c_device_i2c2;
+extern struct platform_device s3c_device_i2c3;
+extern struct platform_device s3c_device_i2c4;
+extern struct platform_device s3c_device_i2c5;
+extern struct platform_device s3c_device_i2c6;
+extern struct platform_device s3c_device_i2c7;
+extern struct platform_device s3c_device_iis;
+extern struct platform_device s3c_device_lcd;
+extern struct platform_device s3c_device_nand;
+extern struct platform_device s3c_device_ohci;
+extern struct platform_device s3c_device_onenand;
+extern struct platform_device s3c_device_rtc;
+extern struct platform_device s3c_device_sdi;
+extern struct platform_device s3c_device_spi0;
+extern struct platform_device s3c_device_spi1;
+extern struct platform_device s3c_device_ts;
+extern struct platform_device s3c_device_timer[];
+extern struct platform_device s3c_device_usbgadget;
+extern struct platform_device s3c_device_usb_hsotg;
+extern struct platform_device s3c_device_usb_hsudc;
+extern struct platform_device s3c_device_wdt;
+
+extern struct platform_device samsung_asoc_idma;
+extern struct platform_device samsung_device_keypad;
+extern struct platform_device samsung_device_pwm;
+
+/* s3c2440 specific devices */
+
+#ifdef CONFIG_CPU_S3C2440
+
+extern struct platform_device s3c_device_camif;
+extern struct platform_device s3c_device_ac97;
+
+#endif
+
+/**
+ * s3c_set_platdata() - helper for setting platform data
+ * @pd: The default platform data for this device.
+ * @pdsize: The size of the platform data.
+ * @pdev: Pointer to the device to fill in.
+ *
+ * This helper replaces a number of calls that copy and then set the
+ * platform data of the device.
+ */
+extern void *s3c_set_platdata(void *pd, size_t pdsize,
+			      struct platform_device *pdev);
+
+#endif /* __PLAT_DEVS_H */
diff --git a/arch/arm/plat-samsung/include/plat/fb-core.h b/arch/arm/plat-samsung/include/plat/fb-core.h
new file mode 100644
index 000000000..bca383efc
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/fb-core.h
@@ -0,0 +1,29 @@
+/*
+ * arch/arm/plat-samsung/include/plat/fb-core.h
+ *
+ * Copyright 2010 Samsung Electronics Co., Ltd.
+ *	Pawel Osciak <p.osciak@samsung.com>
+ *
+ * Samsung framebuffer driver core functions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_PLAT_FB_CORE_H
+#define __ASM_PLAT_FB_CORE_H __FILE__
+
+/*
+ * These functions are only for use with the core support code, such as
+ * the CPU-specific initialization code.
+ */
+
+/* Re-define device name depending on support. */
+static inline void s3c_fb_setname(char *name)
+{
+#ifdef CONFIG_S3C_DEV_FB
+	s3c_device_fb.name = name;
+#endif
+}
+
+#endif /* __ASM_PLAT_FB_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/fb-s3c2410.h b/arch/arm/plat-samsung/include/plat/fb-s3c2410.h
new file mode 100644
index 000000000..4e5d9588b
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/fb-s3c2410.h
@@ -0,0 +1,72 @@
+/* arch/arm/plat-samsung/include/plat/fb-s3c2410.h
+ *
+ * Copyright (c) 2004 Arnaud Patard <arnaud.patard@rtp-net.org>
+ *
+ * Inspired by pxafb.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_FB_S3C2410_H
+#define __ASM_PLAT_FB_S3C2410_H __FILE__
+
+struct s3c2410fb_hw {
+	unsigned long	lcdcon1;
+	unsigned long	lcdcon2;
+	unsigned long	lcdcon3;
+	unsigned long	lcdcon4;
+	unsigned long	lcdcon5;
+};
+
+/* LCD description */
+struct s3c2410fb_display {
+	/* LCD type */
+	unsigned type;
+
+	/* Screen size */
+	unsigned short width;
+	unsigned short height;
+
+	/* Screen info */
+	unsigned short xres;
+	unsigned short yres;
+	unsigned short bpp;
+
+	unsigned pixclock;		/* pixclock in picoseconds */
+	unsigned short left_margin;  /* value in pixels (TFT) or HCLKs (STN) */
+	unsigned short right_margin; /* value in pixels (TFT) or HCLKs (STN) */
+	unsigned short hsync_len;    /* value in pixels (TFT) or HCLKs (STN) */
+	unsigned short upper_margin;	/* value in lines (TFT) or 0 (STN) */
+	unsigned short lower_margin;	/* value in lines (TFT) or 0 (STN) */
+	unsigned short vsync_len;	/* value in lines (TFT) or 0 (STN) */
+
+	/* lcd configuration registers */
+	unsigned long	lcdcon5;
+};
+
+struct s3c2410fb_mach_info {
+
+	struct s3c2410fb_display *displays;	/* attached diplays info */
+	unsigned num_displays;			/* number of defined displays */
+	unsigned default_display;
+
+	/* GPIOs */
+
+	unsigned long	gpcup;
+	unsigned long	gpcup_mask;
+	unsigned long	gpccon;
+	unsigned long	gpccon_mask;
+	unsigned long	gpdup;
+	unsigned long	gpdup_mask;
+	unsigned long	gpdcon;
+	unsigned long	gpdcon_mask;
+
+	/* lpc3600 control register */
+	unsigned long	lpcsel;
+};
+
+extern void __init s3c24xx_fb_set_platdata(struct s3c2410fb_mach_info *);
+
+#endif /* __ASM_PLAT_FB_S3C2410_H */
diff --git a/arch/arm/plat-samsung/include/plat/fb.h b/arch/arm/plat-samsung/include/plat/fb.h
new file mode 100644
index 000000000..b89f8f208
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/fb.h
@@ -0,0 +1,35 @@
+/* arch/arm/plat-samsung/include/plat/fb.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C - FB platform data definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __PLAT_S3C_FB_H
+#define __PLAT_S3C_FB_H __FILE__
+
+#include <linux/platform_data/video_s3c.h>
+
+/**
+ * s3c_fb_set_platdata() - Setup the FB device with platform data.
+ * @pd: The platform data to set. The data is copied from the passed structure
+ *      so the machine data can mark the data __initdata so that any unused
+ *      machines will end up dumping their data at runtime.
+ */
+extern void s3c_fb_set_platdata(struct s3c_fb_platdata *pd);
+
+/**
+ * s3c64xx_fb_gpio_setup_24bpp() - S3C64XX setup function for 24bpp LCD
+ *
+ * Initialise the GPIO for an 24bpp LCD display on the RGB interface.
+ */
+extern void s3c64xx_fb_gpio_setup_24bpp(void);
+
+#endif /* __PLAT_S3C_FB_H */
diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h b/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h
new file mode 100644
index 000000000..a181d7ce8
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/gpio-cfg-helpers.h
@@ -0,0 +1,163 @@
+/* linux/arch/arm/plat-samsung/include/plat/gpio-cfg-helper.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Samsung Platform - GPIO pin configuration helper definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* This is meant for core cpu support, machine or other driver files
+ * should not be including this header.
+ */
+
+#ifndef __PLAT_GPIO_CFG_HELPERS_H
+#define __PLAT_GPIO_CFG_HELPERS_H __FILE__
+
+/* As a note, all gpio configuration functions are entered exclusively, either
+ * with the relevant lock held or the system prevented from doing anything else
+ * by disabling interrupts.
+*/
+
+static inline int samsung_gpio_do_setcfg(struct samsung_gpio_chip *chip,
+					 unsigned int off, unsigned int config)
+{
+	return (chip->config->set_config)(chip, off, config);
+}
+
+static inline unsigned samsung_gpio_do_getcfg(struct samsung_gpio_chip *chip,
+					      unsigned int off)
+{
+	return (chip->config->get_config)(chip, off);
+}
+
+static inline int samsung_gpio_do_setpull(struct samsung_gpio_chip *chip,
+					  unsigned int off, samsung_gpio_pull_t pull)
+{
+	return (chip->config->set_pull)(chip, off, pull);
+}
+
+static inline samsung_gpio_pull_t samsung_gpio_do_getpull(struct samsung_gpio_chip *chip,
+							  unsigned int off)
+{
+	return chip->config->get_pull(chip, off);
+}
+
+/* Pull-{up,down} resistor controls.
+ *
+ * S3C2410,S3C2440 = Pull-UP,
+ * S3C2412,S3C2413 = Pull-Down
+ * S3C6400,S3C6410 = Pull-Both [None,Down,Up,Undef]
+ * S3C2443 = Pull-Both [not same as S3C6400]
+ */
+
+/**
+ * s3c24xx_gpio_setpull_1up() - Pull configuration for choice of up or none.
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ * @param: pull: The pull mode being requested.
+ *
+ * This is a helper function for the case where we have GPIOs with one
+ * bit configuring the presence of a pull-up resistor.
+ */
+extern int s3c24xx_gpio_setpull_1up(struct samsung_gpio_chip *chip,
+				    unsigned int off, samsung_gpio_pull_t pull);
+
+/**
+ * s3c24xx_gpio_setpull_1down() - Pull configuration for choice of down or none
+ * @chip: The gpio chip that is being configured
+ * @off: The offset for the GPIO being configured
+ * @param: pull: The pull mode being requested
+ *
+ * This is a helper function for the case where we have GPIOs with one
+ * bit configuring the presence of a pull-down resistor.
+ */
+extern int s3c24xx_gpio_setpull_1down(struct samsung_gpio_chip *chip,
+				      unsigned int off, samsung_gpio_pull_t pull);
+
+/**
+ * samsung_gpio_setpull_upown() - Pull configuration for choice of up,
+ * down or none
+ *
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ * @param: pull: The pull mode being requested.
+ *
+ * This is a helper function for the case where we have GPIOs with two
+ * bits configuring the presence of a pull resistor, in the following
+ * order:
+ *	00 = No pull resistor connected
+ *	01 = Pull-up resistor connected
+ *	10 = Pull-down resistor connected
+ */
+extern int samsung_gpio_setpull_updown(struct samsung_gpio_chip *chip,
+				       unsigned int off, samsung_gpio_pull_t pull);
+
+/**
+ * samsung_gpio_getpull_updown() - Get configuration for choice of up,
+ * down or none
+ *
+ * @chip: The gpio chip that the GPIO pin belongs to
+ * @off: The offset to the pin to get the configuration of.
+ *
+ * This helper function reads the state of the pull-{up,down} resistor
+ * for the given GPIO in the same case as samsung_gpio_setpull_upown.
+*/
+extern samsung_gpio_pull_t samsung_gpio_getpull_updown(struct samsung_gpio_chip *chip,
+						       unsigned int off);
+
+/**
+ * s3c24xx_gpio_getpull_1up() - Get configuration for choice of up or none
+ * @chip: The gpio chip that the GPIO pin belongs to
+ * @off: The offset to the pin to get the configuration of.
+ *
+ * This helper function reads the state of the pull-up resistor for the
+ * given GPIO in the same case as s3c24xx_gpio_setpull_1up.
+*/
+extern samsung_gpio_pull_t s3c24xx_gpio_getpull_1up(struct samsung_gpio_chip *chip,
+						    unsigned int off);
+
+/**
+ * s3c24xx_gpio_getpull_1down() - Get configuration for choice of down or none
+ * @chip: The gpio chip that the GPIO pin belongs to
+ * @off: The offset to the pin to get the configuration of.
+ *
+ * This helper function reads the state of the pull-down resistor for the
+ * given GPIO in the same case as s3c24xx_gpio_setpull_1down.
+*/
+extern samsung_gpio_pull_t s3c24xx_gpio_getpull_1down(struct samsung_gpio_chip *chip,
+						      unsigned int off);
+
+/**
+ * s3c2443_gpio_setpull() - Pull configuration for s3c2443.
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ * @param: pull: The pull mode being requested.
+ *
+ * This is a helper function for the case where we have GPIOs with two
+ * bits configuring the presence of a pull resistor, in the following
+ * order:
+ *	00 = Pull-up resistor connected
+ *	10 = Pull-down resistor connected
+ *	x1 = No pull up resistor
+ */
+extern int s3c2443_gpio_setpull(struct samsung_gpio_chip *chip,
+				unsigned int off, samsung_gpio_pull_t pull);
+
+/**
+ * s3c2443_gpio_getpull() - Get configuration for s3c2443 pull resistors
+ * @chip: The gpio chip that the GPIO pin belongs to.
+ * @off: The offset to the pin to get the configuration of.
+ *
+ * This helper function reads the state of the pull-{up,down} resistor for the
+ * given GPIO in the same case as samsung_gpio_setpull_upown.
+*/
+extern samsung_gpio_pull_t s3c2443_gpio_getpull(struct samsung_gpio_chip *chip,
+						unsigned int off);
+
+#endif /* __PLAT_GPIO_CFG_HELPERS_H */
diff --git a/arch/arm/plat-samsung/include/plat/gpio-cfg.h b/arch/arm/plat-samsung/include/plat/gpio-cfg.h
new file mode 100644
index 000000000..b5294eff1
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/gpio-cfg.h
@@ -0,0 +1,182 @@
+/* linux/arch/arm/plat-s3c/include/plat/gpio-cfg.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C Platform - GPIO pin configuration
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* This file contains the necessary definitions to get the basic gpio
+ * pin configuration done such as setting a pin to input or output or
+ * changing the pull-{up,down} configurations.
+ */
+
+/* Note, this interface is being added to the s3c64xx arch first and will
+ * be added to the s3c24xx systems later.
+ */
+
+#ifndef __PLAT_GPIO_CFG_H
+#define __PLAT_GPIO_CFG_H __FILE__
+
+#include <linux/types.h>
+
+typedef unsigned int __bitwise__ samsung_gpio_pull_t;
+
+/* forward declaration if gpio-core.h hasn't been included */
+struct samsung_gpio_chip;
+
+/**
+ * struct samsung_gpio_cfg GPIO configuration
+ * @cfg_eint: Configuration setting when used for external interrupt source
+ * @get_pull: Read the current pull configuration for the GPIO
+ * @set_pull: Set the current pull configuraiton for the GPIO
+ * @set_config: Set the current configuration for the GPIO
+ * @get_config: Read the current configuration for the GPIO
+ *
+ * Each chip can have more than one type of GPIO bank available and some
+ * have different capabilites even when they have the same control register
+ * layouts. Provide an point to vector control routine and provide any
+ * per-bank configuration information that other systems such as the
+ * external interrupt code will need.
+ *
+ * @sa samsung_gpio_cfgpin
+ * @sa s3c_gpio_getcfg
+ * @sa s3c_gpio_setpull
+ * @sa s3c_gpio_getpull
+ */
+struct samsung_gpio_cfg {
+	unsigned int	cfg_eint;
+
+	samsung_gpio_pull_t	(*get_pull)(struct samsung_gpio_chip *chip, unsigned offs);
+	int		(*set_pull)(struct samsung_gpio_chip *chip, unsigned offs,
+				    samsung_gpio_pull_t pull);
+
+	unsigned (*get_config)(struct samsung_gpio_chip *chip, unsigned offs);
+	int	 (*set_config)(struct samsung_gpio_chip *chip, unsigned offs,
+			       unsigned config);
+};
+
+#define S3C_GPIO_SPECIAL_MARK	(0xfffffff0)
+#define S3C_GPIO_SPECIAL(x)	(S3C_GPIO_SPECIAL_MARK | (x))
+
+/* Defines for generic pin configurations */
+#define S3C_GPIO_INPUT	(S3C_GPIO_SPECIAL(0))
+#define S3C_GPIO_OUTPUT	(S3C_GPIO_SPECIAL(1))
+#define S3C_GPIO_SFN(x)	(S3C_GPIO_SPECIAL(x))
+
+#define samsung_gpio_is_cfg_special(_cfg) \
+	(((_cfg) & S3C_GPIO_SPECIAL_MARK) == S3C_GPIO_SPECIAL_MARK)
+
+/**
+ * s3c_gpio_cfgpin() - Change the GPIO function of a pin.
+ * @pin pin The pin number to configure.
+ * @to to The configuration for the pin's function.
+ *
+ * Configure which function is actually connected to the external
+ * pin, such as an gpio input, output or some form of special function
+ * connected to an internal peripheral block.
+ *
+ * The @to parameter can be one of the generic S3C_GPIO_INPUT, S3C_GPIO_OUTPUT
+ * or S3C_GPIO_SFN() to indicate one of the possible values that the helper
+ * will then generate the correct bit mask and shift for the configuration.
+ *
+ * If a bank of GPIOs all needs to be set to special-function 2, then
+ * the following code will work:
+ *
+ *	for (gpio = start; gpio < end; gpio++)
+ *		s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
+ *
+ * The @to parameter can also be a specific value already shifted to the
+ * correct position in the control register, although these are discouraged
+ * in newer kernels and are only being kept for compatibility.
+ */
+extern int s3c_gpio_cfgpin(unsigned int pin, unsigned int to);
+
+/**
+ * s3c_gpio_getcfg - Read the current function for a GPIO pin
+ * @pin: The pin to read the configuration value for.
+ *
+ * Read the configuration state of the given @pin, returning a value that
+ * could be passed back to s3c_gpio_cfgpin().
+ *
+ * @sa s3c_gpio_cfgpin
+ */
+extern unsigned s3c_gpio_getcfg(unsigned int pin);
+
+/**
+ * s3c_gpio_cfgpin_range() - Change the GPIO function for configuring pin range
+ * @start: The pin number to start at
+ * @nr: The number of pins to configure from @start.
+ * @cfg: The configuration for the pin's function
+ *
+ * Call s3c_gpio_cfgpin() for the @nr pins starting at @start.
+ *
+ * @sa s3c_gpio_cfgpin.
+ */
+extern int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr,
+				 unsigned int cfg);
+
+/* Define values for the pull-{up,down} available for each gpio pin.
+ *
+ * These values control the state of the weak pull-{up,down} resistors
+ * available on most pins on the S3C series. Not all chips support both
+ * up or down settings, and it may be dependent on the chip that is being
+ * used to whether the particular mode is available.
+ */
+#define S3C_GPIO_PULL_NONE	((__force samsung_gpio_pull_t)0x00)
+#define S3C_GPIO_PULL_DOWN	((__force samsung_gpio_pull_t)0x01)
+#define S3C_GPIO_PULL_UP	((__force samsung_gpio_pull_t)0x02)
+
+/**
+ * s3c_gpio_setpull() - set the state of a gpio pin pull resistor
+ * @pin: The pin number to configure the pull resistor.
+ * @pull: The configuration for the pull resistor.
+ *
+ * This function sets the state of the pull-{up,down} resistor for the
+ * specified pin. It will return 0 if successful, or a negative error
+ * code if the pin cannot support the requested pull setting.
+ *
+ * @pull is one of S3C_GPIO_PULL_NONE, S3C_GPIO_PULL_DOWN or S3C_GPIO_PULL_UP.
+*/
+extern int s3c_gpio_setpull(unsigned int pin, samsung_gpio_pull_t pull);
+
+/**
+ * s3c_gpio_getpull() - get the pull resistor state of a gpio pin
+ * @pin: The pin number to get the settings for
+ *
+ * Read the pull resistor value for the specified pin.
+*/
+extern samsung_gpio_pull_t s3c_gpio_getpull(unsigned int pin);
+
+/* configure `all` aspects of an gpio */
+
+/**
+ * s3c_gpio_cfgall_range() - configure range of gpio functtion and pull.
+ * @start: The gpio number to start at.
+ * @nr: The number of gpio to configure from @start.
+ * @cfg: The configuration to use
+ * @pull: The pull setting to use.
+ *
+ * Run s3c_gpio_cfgpin() and s3c_gpio_setpull() over the gpio range starting
+ * @gpio and running for @size.
+ *
+ * @sa s3c_gpio_cfgpin
+ * @sa s3c_gpio_setpull
+ * @sa s3c_gpio_cfgpin_range
+ */
+extern int s3c_gpio_cfgall_range(unsigned int start, unsigned int nr,
+				 unsigned int cfg, samsung_gpio_pull_t pull);
+
+static inline int s3c_gpio_cfgrange_nopull(unsigned int pin, unsigned int size,
+					   unsigned int cfg)
+{
+	return s3c_gpio_cfgall_range(pin, size, cfg, S3C_GPIO_PULL_NONE);
+}
+
+#endif /* __PLAT_GPIO_CFG_H */
diff --git a/arch/arm/plat-samsung/include/plat/gpio-core.h b/arch/arm/plat-samsung/include/plat/gpio-core.h
new file mode 100644
index 000000000..6ce11bfdc
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/gpio-core.h
@@ -0,0 +1,145 @@
+/* linux/arch/arm/plat-s3c/include/plat/gpio-core.h
+ *
+ * Copyright 2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C Platform - GPIO core
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __PLAT_SAMSUNG_GPIO_CORE_H
+#define __PLAT_SAMSUNG_GPIO_CORE_H
+
+/* Bring in machine-local definitions, especially S3C_GPIO_END */
+#include <mach/gpio-samsung.h>
+
+#define GPIOCON_OFF	(0x00)
+#define GPIODAT_OFF	(0x04)
+
+#define con_4bit_shift(__off) ((__off) * 4)
+
+/* Define the core gpiolib support functions that the s3c platforms may
+ * need to extend or change depending on the hardware and the s3c chip
+ * selected at build or found at run time.
+ *
+ * These definitions are not intended for driver inclusion, there is
+ * nothing here that should not live outside the platform and core
+ * specific code.
+*/
+
+struct samsung_gpio_chip;
+
+/**
+ * struct samsung_gpio_pm - power management (suspend/resume) information
+ * @save: Routine to save the state of the GPIO block
+ * @resume: Routine to resume the GPIO block.
+ */
+struct samsung_gpio_pm {
+	void (*save)(struct samsung_gpio_chip *chip);
+	void (*resume)(struct samsung_gpio_chip *chip);
+};
+
+struct samsung_gpio_cfg;
+
+/**
+ * struct samsung_gpio_chip - wrapper for specific implementation of gpio
+ * @chip: The chip structure to be exported via gpiolib.
+ * @base: The base pointer to the gpio configuration registers.
+ * @group: The group register number for gpio interrupt support.
+ * @irq_base: The base irq number.
+ * @config: special function and pull-resistor control information.
+ * @lock: Lock for exclusive access to this gpio bank.
+ * @pm_save: Save information for suspend/resume support.
+ * @bitmap_gpio_int: Bitmap for representing GPIO interrupt or not.
+ *
+ * This wrapper provides the necessary information for the Samsung
+ * specific gpios being registered with gpiolib.
+ *
+ * The lock protects each gpio bank from multiple access of the shared
+ * configuration registers, or from reading of data whilst another thread
+ * is writing to the register set.
+ *
+ * Each chip has its own lock to avoid any  contention between different
+ * CPU cores trying to get one lock for different GPIO banks, where each
+ * bank of GPIO has its own register space and configuration registers.
+ */
+struct samsung_gpio_chip {
+	struct gpio_chip	chip;
+	struct samsung_gpio_cfg	*config;
+	struct samsung_gpio_pm	*pm;
+	void __iomem		*base;
+	int			irq_base;
+	int			group;
+	spinlock_t		 lock;
+#ifdef CONFIG_PM
+	u32			pm_save[4];
+#endif
+	u32			bitmap_gpio_int;
+};
+
+static inline struct samsung_gpio_chip *to_samsung_gpio(struct gpio_chip *gpc)
+{
+	return container_of(gpc, struct samsung_gpio_chip, chip);
+}
+
+/**
+ * samsung_gpiolib_to_irq - convert gpio pin to irq number
+ * @chip: The gpio chip that the pin belongs to.
+ * @offset: The offset of the pin in the chip.
+ *
+ * This helper returns the irq number calculated from the chip->irq_base and
+ * the provided offset.
+ */
+extern int samsung_gpiolib_to_irq(struct gpio_chip *chip, unsigned int offset);
+
+/* exported for core SoC support to change */
+extern struct samsung_gpio_cfg s3c24xx_gpiocfg_default;
+
+#ifdef CONFIG_S3C_GPIO_TRACK
+extern struct samsung_gpio_chip *s3c_gpios[S3C_GPIO_END];
+
+static inline struct samsung_gpio_chip *samsung_gpiolib_getchip(unsigned int chip)
+{
+	return (chip < S3C_GPIO_END) ? s3c_gpios[chip] : NULL;
+}
+#else
+/* machine specific code should provide samsung_gpiolib_getchip */
+
+extern struct samsung_gpio_chip s3c24xx_gpios[];
+
+static inline struct samsung_gpio_chip *samsung_gpiolib_getchip(unsigned int pin)
+{
+	struct samsung_gpio_chip *chip;
+
+	if (pin > S3C_GPIO_END)
+		return NULL;
+
+	chip = &s3c24xx_gpios[pin/32];
+	return ((pin - chip->chip.base) < chip->chip.ngpio) ? chip : NULL;
+}
+
+static inline void s3c_gpiolib_track(struct samsung_gpio_chip *chip) { }
+#endif
+
+#ifdef CONFIG_PM
+extern struct samsung_gpio_pm samsung_gpio_pm_1bit;
+extern struct samsung_gpio_pm samsung_gpio_pm_2bit;
+extern struct samsung_gpio_pm samsung_gpio_pm_4bit;
+#define __gpio_pm(x) x
+#else
+#define samsung_gpio_pm_1bit NULL
+#define samsung_gpio_pm_2bit NULL
+#define samsung_gpio_pm_4bit NULL
+#define __gpio_pm(x) NULL
+
+#endif /* CONFIG_PM */
+
+/* locking wrappers to deal with multiple access to the same gpio bank */
+#define samsung_gpio_lock(_oc, _fl) spin_lock_irqsave(&(_oc)->lock, _fl)
+#define samsung_gpio_unlock(_oc, _fl) spin_unlock_irqrestore(&(_oc)->lock, _fl)
+
+#endif /* __PLAT_SAMSUNG_GPIO_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/iic-core.h b/arch/arm/plat-samsung/include/plat/iic-core.h
new file mode 100644
index 000000000..f182669b8
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/iic-core.h
@@ -0,0 +1,42 @@
+/* arch/arm/mach-s3c2410/include/mach/iic-core.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C - I2C Controller core functions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_IIC_CORE_H
+#define __ASM_ARCH_IIC_CORE_H __FILE__
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void s3c_i2c0_setname(char *name)
+{
+	/* currently this device is always compiled in */
+	s3c_device_i2c0.name = name;
+}
+
+static inline void s3c_i2c1_setname(char *name)
+{
+#ifdef CONFIG_S3C_DEV_I2C1
+	s3c_device_i2c1.name = name;
+#endif
+}
+
+static inline void s3c_i2c2_setname(char *name)
+{
+#ifdef CONFIG_S3C_DEV_I2C2
+	s3c_device_i2c2.name = name;
+#endif
+}
+
+#endif /* __ASM_ARCH_IIC_H */
diff --git a/arch/arm/plat-samsung/include/plat/irq-uart.h b/arch/arm/plat-samsung/include/plat/irq-uart.h
new file mode 100644
index 000000000..a9331e49b
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/irq-uart.h
@@ -0,0 +1,20 @@
+/* arch/arm/plat-samsung/include/plat/irq-uart.h
+ *
+ * Copyright (c) 2010 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Header file for Samsung SoC UART IRQ demux for S3C64XX and later
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+struct s3c_uart_irq {
+	void __iomem	*regs;
+	unsigned int	 base_irq;
+	unsigned int	 parent_irq;
+};
+
+extern void s3c_init_uart_irqs(struct s3c_uart_irq *irq, unsigned int nr_irqs);
+
diff --git a/arch/arm/plat-samsung/include/plat/keypad-core.h b/arch/arm/plat-samsung/include/plat/keypad-core.h
new file mode 100644
index 000000000..d513e1b3a
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/keypad-core.h
@@ -0,0 +1,31 @@
+/*
+ * linux/arch/arm/plat-samsung/include/plat/keypad-core.h
+ *
+ * Copyright (C) 2010 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ *
+ * Samsung keypad controller core function
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ */
+
+#ifndef __ASM_ARCH_KEYPAD_CORE_H
+#define __ASM_ARCH_KEYPAD_CORE_H
+
+/* These function are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void samsung_keypad_setname(char *name)
+{
+#ifdef CONFIG_SAMSUNG_DEV_KEYPAD
+	samsung_device_keypad.name = name;
+#endif
+}
+
+#endif /* __ASM_ARCH_KEYPAD_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/keypad.h b/arch/arm/plat-samsung/include/plat/keypad.h
new file mode 100644
index 000000000..c81ace332
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/keypad.h
@@ -0,0 +1,31 @@
+/*
+ * Samsung Platform - Keypad platform data definitions
+ *
+ * Copyright (C) 2010 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __PLAT_SAMSUNG_KEYPAD_H
+#define __PLAT_SAMSUNG_KEYPAD_H
+
+#include <linux/input/samsung-keypad.h>
+
+/**
+ * samsung_keypad_set_platdata - Set platform data for Samsung Keypad device.
+ * @pd: Platform data to register to device.
+ *
+ * Register the given platform data for use with Samsung Keypad device.
+ * The call will copy the platform data, so the board definitions can
+ * make the structure itself __initdata.
+ */
+extern void samsung_keypad_set_platdata(struct samsung_keypad_platdata *pd);
+
+/* defined by architecture to configure gpio. */
+extern void samsung_keypad_cfg_gpio(unsigned int rows, unsigned int cols);
+
+#endif /* __PLAT_SAMSUNG_KEYPAD_H */
diff --git a/arch/arm/plat-samsung/include/plat/map-base.h b/arch/arm/plat-samsung/include/plat/map-base.h
new file mode 100644
index 000000000..3ffac4d2e
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/map-base.h
@@ -0,0 +1,46 @@
+/* linux/include/asm-arm/plat-s3c/map.h
+ *
+ * Copyright 2003, 2007 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C - Memory map definitions (virtual addresses)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_MAP_H
+#define __ASM_PLAT_MAP_H __FILE__
+
+/* Fit all our registers in at 0xF6000000 upwards, trying to use as
+ * little of the VA space as possible so vmalloc and friends have a
+ * better chance of getting memory.
+ *
+ * we try to ensure stuff like the IRQ registers are available for
+ * an single MOVS instruction (ie, only 8 bits of set data)
+ */
+
+#define S3C_ADDR_BASE	0xF6000000
+
+#ifndef __ASSEMBLY__
+#define S3C_ADDR(x)	((void __iomem __force *)S3C_ADDR_BASE + (x))
+#else
+#define S3C_ADDR(x)	(S3C_ADDR_BASE + (x))
+#endif
+
+#define S3C_VA_IRQ	S3C_ADDR(0x00000000)	/* irq controller(s) */
+#define S3C_VA_SYS	S3C_ADDR(0x00100000)	/* system control */
+#define S3C_VA_MEM	S3C_ADDR(0x00200000)	/* memory control */
+#define S3C_VA_TIMER	S3C_ADDR(0x00300000)	/* timer block */
+#define S3C_VA_WATCHDOG	S3C_ADDR(0x00400000)	/* watchdog */
+#define S3C_VA_UART	S3C_ADDR(0x01000000)	/* UART */
+
+/* This is used for the CPU specific mappings that may be needed, so that
+ * they do not need to directly used S3C_ADDR() and thus make it easier to
+ * modify the space for mapping.
+ */
+#define S3C_ADDR_CPU(x)	S3C_ADDR(0x00500000 + (x))
+
+#endif /* __ASM_PLAT_MAP_H */
diff --git a/arch/arm/plat-samsung/include/plat/map-s3c.h b/arch/arm/plat-samsung/include/plat/map-s3c.h
new file mode 100644
index 000000000..c0c70a895
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/map-s3c.h
@@ -0,0 +1,84 @@
+/* linux/arch/arm/plat-samsung/include/plat/map-s3c.h
+ *
+ * Copyright (c) 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX - Memory map definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_MAP_S3C_H
+#define __ASM_PLAT_MAP_S3C_H __FILE__
+
+#define S3C24XX_VA_IRQ		S3C_VA_IRQ
+#define S3C24XX_VA_MEMCTRL	S3C_VA_MEM
+#define S3C24XX_VA_UART		S3C_VA_UART
+
+#define S3C24XX_VA_TIMER	S3C_VA_TIMER
+#define S3C24XX_VA_CLKPWR	S3C_VA_SYS
+#define S3C24XX_VA_WATCHDOG	S3C_VA_WATCHDOG
+
+#define S3C2412_VA_SSMC		S3C_ADDR_CPU(0x00000000)
+#define S3C2412_VA_EBI		S3C_ADDR_CPU(0x00100000)
+
+#define S3C2410_PA_UART		(0x50000000)
+#define S3C24XX_PA_UART		S3C2410_PA_UART
+
+#ifndef S3C_UART_OFFSET
+#define S3C_UART_OFFSET		(0x400)
+#endif
+
+/*
+ * GPIO ports
+ *
+ * the calculation for the VA of this must ensure that
+ * it is the same distance apart from the UART in the
+ * phsyical address space, as the initial mapping for the IO
+ * is done as a 1:1 mapping. This puts it (currently) at
+ * 0xFA800000, which is not in the way of any current mapping
+ * by the base system.
+*/
+
+#define S3C2410_PA_GPIO		(0x56000000)
+#define S3C24XX_PA_GPIO		S3C2410_PA_GPIO
+
+#define S3C24XX_VA_GPIO		((S3C24XX_PA_GPIO - S3C24XX_PA_UART) + S3C24XX_VA_UART)
+#define S3C64XX_VA_GPIO		S3C_ADDR_CPU(0x00000000)
+
+#define S3C64XX_VA_MODEM	S3C_ADDR_CPU(0x00100000)
+#define S3C64XX_VA_USB_HSPHY	S3C_ADDR_CPU(0x00200000)
+
+#define S3C_VA_USB_HSPHY	S3C64XX_VA_USB_HSPHY
+
+/*
+ * ISA style IO, for each machine to sort out mappings for,
+ * if it implements it. We reserve two 16M regions for ISA.
+ */
+
+#define S3C2410_ADDR(x)		S3C_ADDR(x)
+
+#define S3C24XX_VA_ISA_WORD	S3C2410_ADDR(0x02000000)
+#define S3C24XX_VA_ISA_BYTE	S3C2410_ADDR(0x03000000)
+
+/* deal with the registers that move under the 2412/2413 */
+
+#if defined(CONFIG_CPU_S3C2412) || defined(CONFIG_CPU_S3C2413)
+#ifndef __ASSEMBLY__
+extern void __iomem *s3c24xx_va_gpio2;
+#endif
+#ifdef CONFIG_CPU_S3C2412_ONLY
+#define S3C24XX_VA_GPIO2	(S3C24XX_VA_GPIO + 0x10)
+#else
+#define S3C24XX_VA_GPIO2 s3c24xx_va_gpio2
+#endif
+#else
+#define s3c24xx_va_gpio2 S3C24XX_VA_GPIO
+#define S3C24XX_VA_GPIO2 S3C24XX_VA_GPIO
+#endif
+
+#include <plat/map-s5p.h>
+
+#endif /* __ASM_PLAT_MAP_S3C_H */
diff --git a/arch/arm/plat-samsung/include/plat/map-s5p.h b/arch/arm/plat-samsung/include/plat/map-s5p.h
new file mode 100644
index 000000000..f5cf2bd20
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/map-s5p.h
@@ -0,0 +1,40 @@
+/* linux/arch/arm/plat-samsung/include/plat/map-s5p.h
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com/
+ *
+ * S5P - Memory map definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_MAP_S5P_H
+#define __ASM_PLAT_MAP_S5P_H __FILE__
+
+#define S5P_VA_CHIPID		S3C_ADDR(0x02000000)
+#define S5P_VA_CMU		S3C_ADDR(0x02100000)
+
+#define S5P_VA_DMC0		S3C_ADDR(0x02440000)
+#define S5P_VA_DMC1		S3C_ADDR(0x02480000)
+#define S5P_VA_SROMC		S3C_ADDR(0x024C0000)
+
+#define S5P_VA_COREPERI_BASE	S3C_ADDR(0x02800000)
+#define S5P_VA_COREPERI(x)	(S5P_VA_COREPERI_BASE + (x))
+#define S5P_VA_SCU		S5P_VA_COREPERI(0x0)
+#define S5P_VA_TWD		S5P_VA_COREPERI(0x600)
+
+#define VA_VIC(x)		(S3C_VA_IRQ + ((x) * 0x10000))
+#define VA_VIC0			VA_VIC(0)
+#define VA_VIC1			VA_VIC(1)
+#define VA_VIC2			VA_VIC(2)
+#define VA_VIC3			VA_VIC(3)
+
+#ifndef S3C_UART_OFFSET
+#define S3C_UART_OFFSET		(0x400)
+#endif
+
+#include <plat/map-s3c.h>
+
+#endif /* __ASM_PLAT_MAP_S5P_H */
diff --git a/arch/arm/plat-samsung/include/plat/nand-core.h b/arch/arm/plat-samsung/include/plat/nand-core.h
new file mode 100644
index 000000000..6de20789a
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/nand-core.h
@@ -0,0 +1,28 @@
+/* arch/arm/plat-samsung/include/plat/nand-core.h
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com/
+ *
+ * S3C -  Nand Controller core functions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_NAND_CORE_H
+#define __ASM_ARCH_NAND_CORE_H __FILE__
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void s3c_nand_setname(char *name)
+{
+#ifdef CONFIG_S3C_DEV_NAND
+	s3c_device_nand.name = name;
+#endif
+}
+
+#endif /* __ASM_ARCH_NAND_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/onenand-core.h b/arch/arm/plat-samsung/include/plat/onenand-core.h
new file mode 100644
index 000000000..7701cb702
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/onenand-core.h
@@ -0,0 +1,37 @@
+/*
+ * linux/arch/arm/plat-samsung/onenand-core.h
+ *
+ *  Copyright (c) 2010 Samsung Electronics
+ *  Kyungmin Park <kyungmin.park@samsung.com>
+ *  Marek Szyprowski <m.szyprowski@samsung.com>
+ *
+ * Samsung OneNAD Controller core functions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_ONENAND_CORE_H
+#define __ASM_ARCH_ONENAND_CORE_H __FILE__
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void s3c_onenand_setname(char *name)
+{
+#ifdef CONFIG_S3C_DEV_ONENAND
+	s3c_device_onenand.name = name;
+#endif
+}
+
+static inline void s3c64xx_onenand1_setname(char *name)
+{
+#ifdef CONFIG_S3C64XX_DEV_ONENAND1
+	s3c64xx_device_onenand1.name = name;
+#endif
+}
+
+#endif /* __ASM_ARCH_ONENAND_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/pm-common.h b/arch/arm/plat-samsung/include/plat/pm-common.h
new file mode 100644
index 000000000..8705f9e0e
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/pm-common.h
@@ -0,0 +1,110 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ *	Tomasz Figa <t.figa@samsung.com>
+ * Copyright (c) 2004 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Written by Ben Dooks, <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __PLAT_SAMSUNG_PM_COMMON_H
+#define __PLAT_SAMSUNG_PM_COMMON_H __FILE__
+
+#include <linux/irq.h>
+
+/* sleep save info */
+
+/**
+ * struct sleep_save - save information for shared peripherals.
+ * @reg: Pointer to the register to save.
+ * @val: Holder for the value saved from reg.
+ *
+ * This describes a list of registers which is used by the pm core and
+ * other subsystem to save and restore register values over suspend.
+ */
+struct sleep_save {
+	void __iomem	*reg;
+	unsigned long	val;
+};
+
+#define SAVE_ITEM(x) \
+	{ .reg = (x) }
+
+/* helper functions to save/restore lists of registers. */
+
+extern void s3c_pm_do_save(struct sleep_save *ptr, int count);
+extern void s3c_pm_do_restore(const struct sleep_save *ptr, int count);
+extern void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count);
+
+/* PM debug functions */
+
+/**
+ * struct pm_uart_save - save block for core UART
+ * @ulcon: Save value for S3C2410_ULCON
+ * @ucon: Save value for S3C2410_UCON
+ * @ufcon: Save value for S3C2410_UFCON
+ * @umcon: Save value for S3C2410_UMCON
+ * @ubrdiv: Save value for S3C2410_UBRDIV
+ *
+ * Save block for UART registers to be held over sleep and restored if they
+ * are needed (say by debug).
+*/
+struct pm_uart_save {
+	u32	ulcon;
+	u32	ucon;
+	u32	ufcon;
+	u32	umcon;
+	u32	ubrdiv;
+	u32	udivslot;
+};
+
+#ifdef CONFIG_SAMSUNG_PM_DEBUG
+/**
+ * s3c_pm_dbg() - low level debug function for use in suspend/resume.
+ * @msg: The message to print.
+ *
+ * This function is used mainly to debug the resume process before the system
+ * can rely on printk/console output. It uses the low-level debugging output
+ * routine printascii() to do its work.
+ */
+extern void s3c_pm_dbg(const char *msg, ...);
+
+/**
+ * s3c_pm_debug_init() - suspend/resume low level debug initialization.
+ * @base: Virtual base of UART to use for suspend/resume debugging.
+ *
+ * This function needs to be called before S3C_PMDBG() can be used, to set up
+ * UART port base address and configuration.
+ */
+extern void s3c_pm_debug_init(void);
+
+#define S3C_PMDBG(fmt...) s3c_pm_dbg(fmt)
+
+extern void s3c_pm_save_uarts(void);
+extern void s3c_pm_restore_uarts(void);
+#else
+#define S3C_PMDBG(fmt...) pr_debug(fmt)
+#define s3c_pm_debug_init() do { } while (0)
+
+static inline void s3c_pm_save_uarts(void) { }
+static inline void s3c_pm_restore_uarts(void) { }
+#endif
+
+/* suspend memory checking */
+
+#ifdef CONFIG_SAMSUNG_PM_CHECK
+extern void s3c_pm_check_prepare(void);
+extern void s3c_pm_check_restore(void);
+extern void s3c_pm_check_cleanup(void);
+extern void s3c_pm_check_store(void);
+#else
+#define s3c_pm_check_prepare() do { } while (0)
+#define s3c_pm_check_restore() do { } while (0)
+#define s3c_pm_check_cleanup() do { } while (0)
+#define s3c_pm_check_store()   do { } while (0)
+#endif
+
+#endif
diff --git a/arch/arm/plat-samsung/include/plat/pm.h b/arch/arm/plat-samsung/include/plat/pm.h
new file mode 100644
index 000000000..7f415ce74
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/pm.h
@@ -0,0 +1,121 @@
+/* arch/arm/plat-samsung/include/plat/pm.h
+ *
+ * Copyright (c) 2004 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Written by Ben Dooks, <ben@simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* s3c_pm_init
+ *
+ * called from board at initialisation time to setup the power
+ * management
+*/
+
+#include <plat/pm-common.h>
+
+struct device;
+
+#ifdef CONFIG_SAMSUNG_PM
+
+extern __init int s3c_pm_init(void);
+extern __init int s3c64xx_pm_init(void);
+
+#else
+
+static inline int s3c_pm_init(void)
+{
+	return 0;
+}
+
+static inline int s3c64xx_pm_init(void)
+{
+	return 0;
+}
+#endif
+
+/* configuration for the IRQ mask over sleep */
+extern unsigned long s3c_irqwake_intmask;
+extern unsigned long s3c_irqwake_eintmask;
+
+/* IRQ masks for IRQs allowed to go to sleep (see irq.c) */
+extern unsigned long s3c_irqwake_intallow;
+#ifdef CONFIG_PM_SLEEP
+extern unsigned long s3c_irqwake_eintallow;
+#else
+#define s3c_irqwake_eintallow 0
+#endif
+
+/* per-cpu sleep functions */
+
+extern void (*pm_cpu_prep)(void);
+extern int (*pm_cpu_sleep)(unsigned long);
+
+/* Flags for PM Control */
+
+extern unsigned long s3c_pm_flags;
+
+/* from sleep.S */
+
+extern int s3c2410_cpu_suspend(unsigned long);
+
+#ifdef CONFIG_PM_SLEEP
+extern int s3c_irq_wake(struct irq_data *data, unsigned int state);
+extern void s3c_cpu_resume(void);
+#else
+#define s3c_irq_wake NULL
+#define s3c_cpu_resume NULL
+#endif
+
+#ifdef CONFIG_SAMSUNG_PM
+extern int s3c_irqext_wake(struct irq_data *data, unsigned int state);
+#else
+#define s3c_irqext_wake NULL
+#endif
+
+#ifdef CONFIG_S3C_PM_DEBUG_LED_SMDK
+/**
+ * s3c_pm_debug_smdkled() - Debug PM suspend/resume via SMDK Board LEDs
+ * @set: set bits for the state of the LEDs
+ * @clear: clear bits for the state of the LEDs.
+ */
+extern void s3c_pm_debug_smdkled(u32 set, u32 clear);
+
+#else
+static inline void s3c_pm_debug_smdkled(u32 set, u32 clear) { }
+#endif /* CONFIG_S3C_PM_DEBUG_LED_SMDK */
+
+/**
+ * s3c_pm_configure_extint() - ensure pins are correctly set for IRQ
+ *
+ * Setup all the necessary GPIO pins for waking the system on external
+ * interrupt.
+ */
+extern void s3c_pm_configure_extint(void);
+
+#ifdef CONFIG_GPIO_SAMSUNG
+/**
+ * samsung_pm_restore_gpios() - restore the state of the gpios after sleep.
+ *
+ * Restore the state of the GPIO pins after sleep, which may involve ensuring
+ * that we do not glitch the state of the pins from that the bootloader's
+ * resume code has done.
+*/
+extern void samsung_pm_restore_gpios(void);
+
+/**
+ * samsung_pm_save_gpios() - save the state of the GPIOs for restoring after sleep.
+ *
+ * Save the GPIO states for resotration on resume. See samsung_pm_restore_gpios().
+ */
+extern void samsung_pm_save_gpios(void);
+#else
+static inline void samsung_pm_restore_gpios(void) {}
+static inline void samsung_pm_save_gpios(void) {}
+#endif
+
+extern void s3c_pm_save_core(void);
+extern void s3c_pm_restore_core(void);
diff --git a/arch/arm/plat-samsung/include/plat/pwm-core.h b/arch/arm/plat-samsung/include/plat/pwm-core.h
new file mode 100644
index 000000000..5bff1facb
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/pwm-core.h
@@ -0,0 +1,22 @@
+/*
+ * Copyright 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Samsung PWM controller platform data helpers.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __ASM_ARCH_PWM_CORE_H
+#define __ASM_ARCH_PWM_CORE_H __FILE__
+
+#include <clocksource/samsung_pwm.h>
+
+#ifdef CONFIG_SAMSUNG_DEV_PWM
+extern void samsung_pwm_set_platdata(struct samsung_pwm_variant *pd);
+#else
+static inline void samsung_pwm_set_platdata(struct samsung_pwm_variant *pd) { }
+#endif
+
+#endif /* __ASM_ARCH_PWM_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/regs-adc.h b/arch/arm/plat-samsung/include/plat/regs-adc.h
new file mode 100644
index 000000000..706121001
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/regs-adc.h
@@ -0,0 +1,68 @@
+/* arch/arm/mach-s3c2410/include/mach/regs-adc.h
+ *
+ * Copyright (c) 2004 Shannon Holland <holland@loser.net>
+ *
+ * This program is free software; yosu can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * S3C2410 ADC registers
+*/
+
+#ifndef __ASM_ARCH_REGS_ADC_H
+#define __ASM_ARCH_REGS_ADC_H "regs-adc.h"
+
+#define S3C2410_ADCREG(x) (x)
+
+#define S3C2410_ADCCON	   S3C2410_ADCREG(0x00)
+#define S3C2410_ADCTSC	   S3C2410_ADCREG(0x04)
+#define S3C2410_ADCDLY	   S3C2410_ADCREG(0x08)
+#define S3C2410_ADCDAT0	   S3C2410_ADCREG(0x0C)
+#define S3C2410_ADCDAT1	   S3C2410_ADCREG(0x10)
+#define S3C64XX_ADCUPDN		S3C2410_ADCREG(0x14)
+#define S3C2443_ADCMUX		S3C2410_ADCREG(0x18)
+#define S3C64XX_ADCCLRINT	S3C2410_ADCREG(0x18)
+#define S5P_ADCMUX		S3C2410_ADCREG(0x1C)
+#define S3C64XX_ADCCLRINTPNDNUP	S3C2410_ADCREG(0x20)
+
+
+/* ADCCON Register Bits */
+#define S3C64XX_ADCCON_RESSEL		(1<<16)
+#define S3C2410_ADCCON_ECFLG		(1<<15)
+#define S3C2410_ADCCON_PRSCEN		(1<<14)
+#define S3C2410_ADCCON_PRSCVL(x)	(((x)&0xFF)<<6)
+#define S3C2410_ADCCON_PRSCVLMASK	(0xFF<<6)
+#define S3C2410_ADCCON_SELMUX(x)	(((x)&0x7)<<3)
+#define S3C2410_ADCCON_MUXMASK		(0x7<<3)
+#define S3C2416_ADCCON_RESSEL		(1 << 3)
+#define S3C2410_ADCCON_STDBM		(1<<2)
+#define S3C2410_ADCCON_READ_START	(1<<1)
+#define S3C2410_ADCCON_ENABLE_START	(1<<0)
+#define S3C2410_ADCCON_STARTMASK	(0x3<<0)
+
+
+/* ADCTSC Register Bits */
+#define S3C2443_ADCTSC_UD_SEN		(1 << 8)
+#define S3C2410_ADCTSC_YM_SEN		(1<<7)
+#define S3C2410_ADCTSC_YP_SEN		(1<<6)
+#define S3C2410_ADCTSC_XM_SEN		(1<<5)
+#define S3C2410_ADCTSC_XP_SEN		(1<<4)
+#define S3C2410_ADCTSC_PULL_UP_DISABLE	(1<<3)
+#define S3C2410_ADCTSC_AUTO_PST		(1<<2)
+#define S3C2410_ADCTSC_XY_PST(x)	(((x)&0x3)<<0)
+
+/* ADCDAT0 Bits */
+#define S3C2410_ADCDAT0_UPDOWN		(1<<15)
+#define S3C2410_ADCDAT0_AUTO_PST	(1<<14)
+#define S3C2410_ADCDAT0_XY_PST		(0x3<<12)
+#define S3C2410_ADCDAT0_XPDATA_MASK	(0x03FF)
+
+/* ADCDAT1 Bits */
+#define S3C2410_ADCDAT1_UPDOWN		(1<<15)
+#define S3C2410_ADCDAT1_AUTO_PST	(1<<14)
+#define S3C2410_ADCDAT1_XY_PST		(0x3<<12)
+#define S3C2410_ADCDAT1_YPDATA_MASK	(0x03FF)
+
+#endif /* __ASM_ARCH_REGS_ADC_H */
+
+
diff --git a/arch/arm/plat-samsung/include/plat/regs-irqtype.h b/arch/arm/plat-samsung/include/plat/regs-irqtype.h
new file mode 100644
index 000000000..c63cd3fc5
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/regs-irqtype.h
@@ -0,0 +1,21 @@
+/* arch/arm/plat-s3c/include/plat/regs-irqtype.h
+ *
+ * Copyright 2008 Simtec Electronics
+ *      Ben Dooks <ben@simtec.co.uk>
+ *      http://armlinux.simtec.co.uk/
+ *
+ * S3C - IRQ detection types.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* values for S3C2410_EXTINT0/1/2 and other cpus in the series, including
+ * the S3C64XX
+*/
+#define S3C2410_EXTINT_LOWLEV	 (0x00)
+#define S3C2410_EXTINT_HILEV	 (0x01)
+#define S3C2410_EXTINT_FALLEDGE	 (0x02)
+#define S3C2410_EXTINT_RISEEDGE	 (0x04)
+#define S3C2410_EXTINT_BOTHEDGE	 (0x06)
diff --git a/arch/arm/plat-samsung/include/plat/regs-spi.h b/arch/arm/plat-samsung/include/plat/regs-spi.h
new file mode 100644
index 000000000..552fe7cfe
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/regs-spi.h
@@ -0,0 +1,48 @@
+/* arch/arm/plat-samsung/include/plat/regs-spi.h
+ *
+ * Copyright (c) 2004 Fetron GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * S3C2410 SPI register definition
+*/
+
+#ifndef __ASM_ARCH_REGS_SPI_H
+#define __ASM_ARCH_REGS_SPI_H
+
+#define S3C2410_SPI1		(0x20)
+#define S3C2412_SPI1		(0x100)
+
+#define S3C2410_SPCON		(0x00)
+
+#define S3C2410_SPCON_SMOD_DMA	(2 << 5)	/* DMA mode */
+#define S3C2410_SPCON_SMOD_INT	(1 << 5)	/* interrupt mode */
+#define S3C2410_SPCON_SMOD_POLL	(0 << 5)	/* polling mode */
+#define S3C2410_SPCON_ENSCK	(1 << 4)	/* Enable SCK */
+#define S3C2410_SPCON_MSTR	(1 << 3)	/* Master:1, Slave:0 select */
+#define S3C2410_SPCON_CPOL_HIGH	(1 << 2)	/* Clock polarity select */
+#define S3C2410_SPCON_CPOL_LOW	(0 << 2)	/* Clock polarity select */
+
+#define S3C2410_SPCON_CPHA_FMTB	(1 << 1)	/* Clock Phase Select */
+#define S3C2410_SPCON_CPHA_FMTA	(0 << 1)	/* Clock Phase Select */
+
+#define S3C2410_SPSTA		(0x04)
+
+#define S3C2410_SPSTA_DCOL	(1 << 2)	/* Data Collision Error */
+#define S3C2410_SPSTA_MULD	(1 << 1)	/* Multi Master Error */
+#define S3C2410_SPSTA_READY	(1 << 0)	/* Data Tx/Rx ready */
+#define S3C2412_SPSTA_READY_ORG	(1 << 3)
+
+#define S3C2410_SPPIN		(0x08)
+
+#define S3C2410_SPPIN_ENMUL	(1 << 2)	/* Multi Master Error detect */
+#define S3C2410_SPPIN_RESERVED	(1 << 1)
+#define S3C2410_SPPIN_KEEP	(1 << 0)	/* Master Out keep */
+
+#define S3C2410_SPPRE		(0x0C)
+#define S3C2410_SPTDAT		(0x10)
+#define S3C2410_SPRDAT		(0x14)
+
+#endif /* __ASM_ARCH_REGS_SPI_H */
diff --git a/arch/arm/plat-samsung/include/plat/regs-srom.h b/arch/arm/plat-samsung/include/plat/regs-srom.h
new file mode 100644
index 000000000..9b6729c81
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/regs-srom.h
@@ -0,0 +1,54 @@
+/* linux/arch/arm/plat-samsung/include/plat/regs-srom.h
+ *
+ * Copyright (c) 2010 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * S5P SROMC register definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __PLAT_SAMSUNG_REGS_SROM_H
+#define __PLAT_SAMSUNG_REGS_SROM_H __FILE__
+
+#include <mach/map.h>
+
+#define S5P_SROMREG(x)		(S5P_VA_SROMC + (x))
+
+#define S5P_SROM_BW		S5P_SROMREG(0x0)
+#define S5P_SROM_BC0		S5P_SROMREG(0x4)
+#define S5P_SROM_BC1		S5P_SROMREG(0x8)
+#define S5P_SROM_BC2		S5P_SROMREG(0xc)
+#define S5P_SROM_BC3		S5P_SROMREG(0x10)
+#define S5P_SROM_BC4		S5P_SROMREG(0x14)
+#define S5P_SROM_BC5		S5P_SROMREG(0x18)
+
+/* one register BW holds 4 x 4-bit packed settings for NCS0 - NCS3 */
+
+#define S5P_SROM_BW__DATAWIDTH__SHIFT		0
+#define S5P_SROM_BW__ADDRMODE__SHIFT		1
+#define S5P_SROM_BW__WAITENABLE__SHIFT		2
+#define S5P_SROM_BW__BYTEENABLE__SHIFT		3
+
+#define S5P_SROM_BW__CS_MASK			0xf
+
+#define S5P_SROM_BW__NCS0__SHIFT		0
+#define S5P_SROM_BW__NCS1__SHIFT		4
+#define S5P_SROM_BW__NCS2__SHIFT		8
+#define S5P_SROM_BW__NCS3__SHIFT		12
+#define S5P_SROM_BW__NCS4__SHIFT		16
+#define S5P_SROM_BW__NCS5__SHIFT		20
+
+/* applies to same to BCS0 - BCS3 */
+
+#define S5P_SROM_BCX__PMC__SHIFT		0
+#define S5P_SROM_BCX__TACP__SHIFT		4
+#define S5P_SROM_BCX__TCAH__SHIFT		8
+#define S5P_SROM_BCX__TCOH__SHIFT		12
+#define S5P_SROM_BCX__TACC__SHIFT		16
+#define S5P_SROM_BCX__TCOS__SHIFT		24
+#define S5P_SROM_BCX__TACS__SHIFT		28
+
+#endif /* __PLAT_SAMSUNG_REGS_SROM_H */
diff --git a/arch/arm/plat-samsung/include/plat/regs-udc.h b/arch/arm/plat-samsung/include/plat/regs-udc.h
new file mode 100644
index 000000000..4003d3dab
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/regs-udc.h
@@ -0,0 +1,151 @@
+/* arch/arm/plat-samsung/include/plat/regs-udc.h
+ *
+ * Copyright (C) 2004 Herbert Poetzl <herbert@13thfloor.at>
+ *
+ * This include file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+*/
+
+#ifndef __ASM_ARCH_REGS_UDC_H
+#define __ASM_ARCH_REGS_UDC_H
+
+#define S3C2410_USBDREG(x) (x)
+
+#define S3C2410_UDC_FUNC_ADDR_REG	S3C2410_USBDREG(0x0140)
+#define S3C2410_UDC_PWR_REG		S3C2410_USBDREG(0x0144)
+#define S3C2410_UDC_EP_INT_REG		S3C2410_USBDREG(0x0148)
+
+#define S3C2410_UDC_USB_INT_REG		S3C2410_USBDREG(0x0158)
+#define S3C2410_UDC_EP_INT_EN_REG	S3C2410_USBDREG(0x015c)
+
+#define S3C2410_UDC_USB_INT_EN_REG	S3C2410_USBDREG(0x016c)
+
+#define S3C2410_UDC_FRAME_NUM1_REG	S3C2410_USBDREG(0x0170)
+#define S3C2410_UDC_FRAME_NUM2_REG	S3C2410_USBDREG(0x0174)
+
+#define S3C2410_UDC_EP0_FIFO_REG	S3C2410_USBDREG(0x01c0)
+#define S3C2410_UDC_EP1_FIFO_REG	S3C2410_USBDREG(0x01c4)
+#define S3C2410_UDC_EP2_FIFO_REG	S3C2410_USBDREG(0x01c8)
+#define S3C2410_UDC_EP3_FIFO_REG	S3C2410_USBDREG(0x01cc)
+#define S3C2410_UDC_EP4_FIFO_REG	S3C2410_USBDREG(0x01d0)
+
+#define S3C2410_UDC_EP1_DMA_CON		S3C2410_USBDREG(0x0200)
+#define S3C2410_UDC_EP1_DMA_UNIT	S3C2410_USBDREG(0x0204)
+#define S3C2410_UDC_EP1_DMA_FIFO	S3C2410_USBDREG(0x0208)
+#define S3C2410_UDC_EP1_DMA_TTC_L	S3C2410_USBDREG(0x020c)
+#define S3C2410_UDC_EP1_DMA_TTC_M	S3C2410_USBDREG(0x0210)
+#define S3C2410_UDC_EP1_DMA_TTC_H	S3C2410_USBDREG(0x0214)
+
+#define S3C2410_UDC_EP2_DMA_CON		S3C2410_USBDREG(0x0218)
+#define S3C2410_UDC_EP2_DMA_UNIT	S3C2410_USBDREG(0x021c)
+#define S3C2410_UDC_EP2_DMA_FIFO	S3C2410_USBDREG(0x0220)
+#define S3C2410_UDC_EP2_DMA_TTC_L	S3C2410_USBDREG(0x0224)
+#define S3C2410_UDC_EP2_DMA_TTC_M	S3C2410_USBDREG(0x0228)
+#define S3C2410_UDC_EP2_DMA_TTC_H	S3C2410_USBDREG(0x022c)
+
+#define S3C2410_UDC_EP3_DMA_CON		S3C2410_USBDREG(0x0240)
+#define S3C2410_UDC_EP3_DMA_UNIT	S3C2410_USBDREG(0x0244)
+#define S3C2410_UDC_EP3_DMA_FIFO	S3C2410_USBDREG(0x0248)
+#define S3C2410_UDC_EP3_DMA_TTC_L	S3C2410_USBDREG(0x024c)
+#define S3C2410_UDC_EP3_DMA_TTC_M	S3C2410_USBDREG(0x0250)
+#define S3C2410_UDC_EP3_DMA_TTC_H	S3C2410_USBDREG(0x0254)
+
+#define S3C2410_UDC_EP4_DMA_CON		S3C2410_USBDREG(0x0258)
+#define S3C2410_UDC_EP4_DMA_UNIT	S3C2410_USBDREG(0x025c)
+#define S3C2410_UDC_EP4_DMA_FIFO	S3C2410_USBDREG(0x0260)
+#define S3C2410_UDC_EP4_DMA_TTC_L	S3C2410_USBDREG(0x0264)
+#define S3C2410_UDC_EP4_DMA_TTC_M	S3C2410_USBDREG(0x0268)
+#define S3C2410_UDC_EP4_DMA_TTC_H	S3C2410_USBDREG(0x026c)
+
+#define S3C2410_UDC_INDEX_REG		S3C2410_USBDREG(0x0178)
+
+/* indexed registers */
+
+#define S3C2410_UDC_MAXP_REG		S3C2410_USBDREG(0x0180)
+
+#define S3C2410_UDC_EP0_CSR_REG		S3C2410_USBDREG(0x0184)
+
+#define S3C2410_UDC_IN_CSR1_REG		S3C2410_USBDREG(0x0184)
+#define S3C2410_UDC_IN_CSR2_REG		S3C2410_USBDREG(0x0188)
+
+#define S3C2410_UDC_OUT_CSR1_REG	S3C2410_USBDREG(0x0190)
+#define S3C2410_UDC_OUT_CSR2_REG	S3C2410_USBDREG(0x0194)
+#define S3C2410_UDC_OUT_FIFO_CNT1_REG	S3C2410_USBDREG(0x0198)
+#define S3C2410_UDC_OUT_FIFO_CNT2_REG	S3C2410_USBDREG(0x019c)
+
+#define S3C2410_UDC_FUNCADDR_UPDATE	(1 << 7)
+
+#define S3C2410_UDC_PWR_ISOUP		(1 << 7) /* R/W */
+#define S3C2410_UDC_PWR_RESET		(1 << 3) /* R   */
+#define S3C2410_UDC_PWR_RESUME		(1 << 2) /* R/W */
+#define S3C2410_UDC_PWR_SUSPEND		(1 << 1) /* R   */
+#define S3C2410_UDC_PWR_ENSUSPEND	(1 << 0) /* R/W */
+
+#define S3C2410_UDC_PWR_DEFAULT		(0x00)
+
+#define S3C2410_UDC_INT_EP4		(1 << 4) /* R/W (clear only) */
+#define S3C2410_UDC_INT_EP3		(1 << 3) /* R/W (clear only) */
+#define S3C2410_UDC_INT_EP2		(1 << 2) /* R/W (clear only) */
+#define S3C2410_UDC_INT_EP1		(1 << 1) /* R/W (clear only) */
+#define S3C2410_UDC_INT_EP0		(1 << 0) /* R/W (clear only) */
+
+#define S3C2410_UDC_USBINT_RESET	(1 << 2) /* R/W (clear only) */
+#define S3C2410_UDC_USBINT_RESUME	(1 << 1) /* R/W (clear only) */
+#define S3C2410_UDC_USBINT_SUSPEND	(1 << 0) /* R/W (clear only) */
+
+#define S3C2410_UDC_INTE_EP4		(1 << 4) /* R/W */
+#define S3C2410_UDC_INTE_EP3		(1 << 3) /* R/W */
+#define S3C2410_UDC_INTE_EP2		(1 << 2) /* R/W */
+#define S3C2410_UDC_INTE_EP1		(1 << 1) /* R/W */
+#define S3C2410_UDC_INTE_EP0		(1 << 0) /* R/W */
+
+#define S3C2410_UDC_USBINTE_RESET	(1 << 2) /* R/W */
+#define S3C2410_UDC_USBINTE_SUSPEND	(1 << 0) /* R/W */
+
+#define S3C2410_UDC_INDEX_EP0		(0x00)
+#define S3C2410_UDC_INDEX_EP1		(0x01)
+#define S3C2410_UDC_INDEX_EP2		(0x02)
+#define S3C2410_UDC_INDEX_EP3		(0x03)
+#define S3C2410_UDC_INDEX_EP4		(0x04)
+
+#define S3C2410_UDC_ICSR1_CLRDT		(1 << 6) /* R/W */
+#define S3C2410_UDC_ICSR1_SENTSTL	(1 << 5) /* R/W (clear only) */
+#define S3C2410_UDC_ICSR1_SENDSTL	(1 << 4) /* R/W */
+#define S3C2410_UDC_ICSR1_FFLUSH	(1 << 3) /* W   (set only) */
+#define S3C2410_UDC_ICSR1_UNDRUN	(1 << 2) /* R/W (clear only) */
+#define S3C2410_UDC_ICSR1_PKTRDY	(1 << 0) /* R/W (set only) */
+
+#define S3C2410_UDC_ICSR2_AUTOSET	(1 << 7) /* R/W */
+#define S3C2410_UDC_ICSR2_ISO		(1 << 6) /* R/W */
+#define S3C2410_UDC_ICSR2_MODEIN	(1 << 5) /* R/W */
+#define S3C2410_UDC_ICSR2_DMAIEN	(1 << 4) /* R/W */
+
+#define S3C2410_UDC_OCSR1_CLRDT		(1 << 7) /* R/W */
+#define S3C2410_UDC_OCSR1_SENTSTL	(1 << 6) /* R/W (clear only) */
+#define S3C2410_UDC_OCSR1_SENDSTL	(1 << 5) /* R/W */
+#define S3C2410_UDC_OCSR1_FFLUSH	(1 << 4) /* R/W */
+#define S3C2410_UDC_OCSR1_DERROR	(1 << 3) /* R   */
+#define S3C2410_UDC_OCSR1_OVRRUN	(1 << 2) /* R/W (clear only) */
+#define S3C2410_UDC_OCSR1_PKTRDY	(1 << 0) /* R/W (clear only) */
+
+#define S3C2410_UDC_OCSR2_AUTOCLR	(1 << 7) /* R/W */
+#define S3C2410_UDC_OCSR2_ISO		(1 << 6) /* R/W */
+#define S3C2410_UDC_OCSR2_DMAIEN	(1 << 5) /* R/W */
+
+#define S3C2410_UDC_EP0_CSR_OPKRDY	(1 << 0)
+#define S3C2410_UDC_EP0_CSR_IPKRDY	(1 << 1)
+#define S3C2410_UDC_EP0_CSR_SENTSTL	(1 << 2)
+#define S3C2410_UDC_EP0_CSR_DE		(1 << 3)
+#define S3C2410_UDC_EP0_CSR_SE		(1 << 4)
+#define S3C2410_UDC_EP0_CSR_SENDSTL	(1 << 5)
+#define S3C2410_UDC_EP0_CSR_SOPKTRDY	(1 << 6)
+#define S3C2410_UDC_EP0_CSR_SSE		(1 << 7)
+
+#define S3C2410_UDC_MAXP_8		(1 << 0)
+#define S3C2410_UDC_MAXP_16		(1 << 1)
+#define S3C2410_UDC_MAXP_32		(1 << 2)
+#define S3C2410_UDC_MAXP_64		(1 << 3)
+
+#endif
diff --git a/arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h b/arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h
new file mode 100644
index 000000000..fcf279662
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h
@@ -0,0 +1,51 @@
+/* arch/arm/plat-s3c/include/plat/regs-usb-hsotg-phy.h
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *      http://armlinux.simtec.co.uk/
+ *      Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C - USB2.0 Highspeed/OtG device PHY registers
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* Note, this is a separate header file as some of the clock framework
+ * needs to touch this if the clk_48m is used as the USB OHCI or other
+ * peripheral source.
+*/
+
+#ifndef __PLAT_S3C64XX_REGS_USB_HSOTG_PHY_H
+#define __PLAT_S3C64XX_REGS_USB_HSOTG_PHY_H __FILE__
+
+/* S3C64XX_PA_USB_HSPHY */
+
+#define S3C_HSOTG_PHYREG(x)	((x) + S3C_VA_USB_HSPHY)
+
+#define S3C_PHYPWR				S3C_HSOTG_PHYREG(0x00)
+#define S3C_PHYPWR_NORMAL_MASK			(0x19 << 0)
+#define S3C_PHYPWR_OTG_DISABLE			(1 << 4)
+#define S3C_PHYPWR_ANALOG_POWERDOWN		(1 << 3)
+#define SRC_PHYPWR_FORCE_SUSPEND		(1 << 1)
+
+#define S3C_PHYCLK				S3C_HSOTG_PHYREG(0x04)
+#define S3C_PHYCLK_MODE_USB11			(1 << 6)
+#define S3C_PHYCLK_EXT_OSC			(1 << 5)
+#define S3C_PHYCLK_CLK_FORCE			(1 << 4)
+#define S3C_PHYCLK_ID_PULL			(1 << 2)
+#define S3C_PHYCLK_CLKSEL_MASK			(0x3 << 0)
+#define S3C_PHYCLK_CLKSEL_SHIFT			(0)
+#define S3C_PHYCLK_CLKSEL_48M			(0x0 << 0)
+#define S3C_PHYCLK_CLKSEL_12M			(0x2 << 0)
+#define S3C_PHYCLK_CLKSEL_24M			(0x3 << 0)
+
+#define S3C_RSTCON				S3C_HSOTG_PHYREG(0x08)
+#define S3C_RSTCON_PHYCLK			(1 << 2)
+#define S3C_RSTCON_HCLK				(1 << 1)
+#define S3C_RSTCON_PHY				(1 << 0)
+
+#define S3C_PHYTUNE				S3C_HSOTG_PHYREG(0x20)
+
+#endif /* __PLAT_S3C64XX_REGS_USB_HSOTG_PHY_H */
diff --git a/arch/arm/plat-samsung/include/plat/samsung-time.h b/arch/arm/plat-samsung/include/plat/samsung-time.h
new file mode 100644
index 000000000..209464ade
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/samsung-time.h
@@ -0,0 +1,30 @@
+/* linux/arch/arm/plat-samsung/include/plat/samsung-time.h
+ *
+ * Copyright 2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com/
+ *
+ * Header file for samsung s3c and s5p time support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_PLAT_SAMSUNG_TIME_H
+#define __ASM_PLAT_SAMSUNG_TIME_H __FILE__
+
+/* SAMSUNG HR-Timer Clock mode */
+enum samsung_timer_mode {
+	SAMSUNG_PWM0,
+	SAMSUNG_PWM1,
+	SAMSUNG_PWM2,
+	SAMSUNG_PWM3,
+	SAMSUNG_PWM4,
+};
+
+extern void __init samsung_set_timer_source(enum samsung_timer_mode event,
+					enum samsung_timer_mode source);
+
+extern void __init samsung_timer_init(void);
+
+#endif /* __ASM_PLAT_SAMSUNG_TIME_H */
diff --git a/arch/arm/plat-samsung/include/plat/sdhci.h b/arch/arm/plat-samsung/include/plat/sdhci.h
new file mode 100644
index 000000000..2787553c3
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/sdhci.h
@@ -0,0 +1,166 @@
+/* linux/arch/arm/plat-samsung/include/plat/sdhci.h
+ *
+ * Copyright (c) 2011 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C Platform - SDHCI (HSMMC) platform data definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __PLAT_S3C_SDHCI_H
+#define __PLAT_S3C_SDHCI_H __FILE__
+
+#include <linux/platform_data/mmc-sdhci-s3c.h>
+#include <plat/devs.h>
+
+/* s3c_sdhci_set_platdata() - common helper for setting SDHCI platform data
+ * @pd: The default platform data for this device.
+ * @set: Pointer to the platform data to fill in.
+ */
+extern void s3c_sdhci_set_platdata(struct s3c_sdhci_platdata *pd,
+				    struct s3c_sdhci_platdata *set);
+
+/**
+ * s3c_sdhci0_set_platdata - Set platform data for S3C SDHCI device.
+ * @pd: Platform data to register to device.
+ *
+ * Register the given platform data for use withe S3C SDHCI device.
+ * The call will copy the platform data, so the board definitions can
+ * make the structure itself __initdata.
+ */
+extern void s3c_sdhci0_set_platdata(struct s3c_sdhci_platdata *pd);
+extern void s3c_sdhci1_set_platdata(struct s3c_sdhci_platdata *pd);
+extern void s3c_sdhci2_set_platdata(struct s3c_sdhci_platdata *pd);
+extern void s3c_sdhci3_set_platdata(struct s3c_sdhci_platdata *pd);
+
+/* Default platform data, exported so that per-cpu initialisation can
+ * set the correct one when there are more than one cpu type selected.
+*/
+
+extern struct s3c_sdhci_platdata s3c_hsmmc0_def_platdata;
+extern struct s3c_sdhci_platdata s3c_hsmmc1_def_platdata;
+extern struct s3c_sdhci_platdata s3c_hsmmc2_def_platdata;
+extern struct s3c_sdhci_platdata s3c_hsmmc3_def_platdata;
+
+/* Helper function availability */
+
+extern void s3c2416_setup_sdhci0_cfg_gpio(struct platform_device *, int w);
+extern void s3c2416_setup_sdhci1_cfg_gpio(struct platform_device *, int w);
+extern void s3c64xx_setup_sdhci0_cfg_gpio(struct platform_device *, int w);
+extern void s3c64xx_setup_sdhci1_cfg_gpio(struct platform_device *, int w);
+extern void s3c64xx_setup_sdhci2_cfg_gpio(struct platform_device *, int w);
+
+/* S3C2416 SDHCI setup */
+
+#ifdef CONFIG_S3C2416_SETUP_SDHCI
+static inline void s3c2416_default_sdhci0(void)
+{
+#ifdef CONFIG_S3C_DEV_HSMMC
+	s3c_hsmmc0_def_platdata.cfg_gpio = s3c2416_setup_sdhci0_cfg_gpio;
+#endif /* CONFIG_S3C_DEV_HSMMC */
+}
+
+static inline void s3c2416_default_sdhci1(void)
+{
+#ifdef CONFIG_S3C_DEV_HSMMC1
+	s3c_hsmmc1_def_platdata.cfg_gpio = s3c2416_setup_sdhci1_cfg_gpio;
+#endif /* CONFIG_S3C_DEV_HSMMC1 */
+}
+
+#else
+static inline void s3c2416_default_sdhci0(void) { }
+static inline void s3c2416_default_sdhci1(void) { }
+
+#endif /* CONFIG_S3C2416_SETUP_SDHCI */
+
+/* S3C64XX SDHCI setup */
+
+#ifdef CONFIG_S3C64XX_SETUP_SDHCI
+static inline void s3c6400_default_sdhci0(void)
+{
+#ifdef CONFIG_S3C_DEV_HSMMC
+	s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio;
+#endif
+}
+
+static inline void s3c6400_default_sdhci1(void)
+{
+#ifdef CONFIG_S3C_DEV_HSMMC1
+	s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio;
+#endif
+}
+
+static inline void s3c6400_default_sdhci2(void)
+{
+#ifdef CONFIG_S3C_DEV_HSMMC2
+	s3c_hsmmc2_def_platdata.cfg_gpio = s3c64xx_setup_sdhci2_cfg_gpio;
+#endif
+}
+
+static inline void s3c6410_default_sdhci0(void)
+{
+#ifdef CONFIG_S3C_DEV_HSMMC
+	s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio;
+#endif
+}
+
+static inline void s3c6410_default_sdhci1(void)
+{
+#ifdef CONFIG_S3C_DEV_HSMMC1
+	s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio;
+#endif
+}
+
+static inline void s3c6410_default_sdhci2(void)
+{
+#ifdef CONFIG_S3C_DEV_HSMMC2
+	s3c_hsmmc2_def_platdata.cfg_gpio = s3c64xx_setup_sdhci2_cfg_gpio;
+#endif
+}
+
+#else
+static inline void s3c6410_default_sdhci0(void) { }
+static inline void s3c6410_default_sdhci1(void) { }
+static inline void s3c6410_default_sdhci2(void) { }
+static inline void s3c6400_default_sdhci0(void) { }
+static inline void s3c6400_default_sdhci1(void) { }
+static inline void s3c6400_default_sdhci2(void) { }
+
+#endif /* CONFIG_S3C64XX_SETUP_SDHCI */
+
+static inline void s3c_sdhci_setname(int id, char *name)
+{
+	switch (id) {
+#ifdef CONFIG_S3C_DEV_HSMMC
+	case 0:
+		s3c_device_hsmmc0.name = name;
+		break;
+#endif
+#ifdef CONFIG_S3C_DEV_HSMMC1
+	case 1:
+		s3c_device_hsmmc1.name = name;
+		break;
+#endif
+#ifdef CONFIG_S3C_DEV_HSMMC2
+	case 2:
+		s3c_device_hsmmc2.name = name;
+		break;
+#endif
+#ifdef CONFIG_S3C_DEV_HSMMC3
+	case 3:
+		s3c_device_hsmmc3.name = name;
+		break;
+#endif
+	default:
+		break;
+	}
+}
+#endif /* __PLAT_S3C_SDHCI_H */
diff --git a/arch/arm/plat-samsung/include/plat/spi-core.h b/arch/arm/plat-samsung/include/plat/spi-core.h
new file mode 100644
index 000000000..0b9428ab3
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/spi-core.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2012 Heiko Stuebner <heiko@sntech.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __PLAT_S3C_SPI_CORE_H
+#define __PLAT_S3C_SPI_CORE_H
+
+/* These functions are only for use with the core support code, such as
+ * the cpu specific initialisation code
+ */
+
+/* re-define device name depending on support. */
+static inline void s3c64xx_spi_setname(char *name)
+{
+#ifdef CONFIG_S3C64XX_DEV_SPI0
+	s3c64xx_device_spi0.name = name;
+#endif
+#ifdef CONFIG_S3C64XX_DEV_SPI1
+	s3c64xx_device_spi1.name = name;
+#endif
+#ifdef CONFIG_S3C64XX_DEV_SPI2
+	s3c64xx_device_spi2.name = name;
+#endif
+}
+
+#endif /* __PLAT_S3C_SPI_CORE_H */
diff --git a/arch/arm/plat-samsung/include/plat/usb-phy.h b/arch/arm/plat-samsung/include/plat/usb-phy.h
new file mode 100644
index 000000000..ab34dfadb
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/usb-phy.h
@@ -0,0 +1,19 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __PLAT_SAMSUNG_USB_PHY_H
+#define __PLAT_SAMSUNG_USB_PHY_H __FILE__
+
+#include <linux/usb/samsung_usb_phy.h>
+
+extern int s5p_usb_phy_init(struct platform_device *pdev, int type);
+extern int s5p_usb_phy_exit(struct platform_device *pdev, int type);
+
+#endif /* __PLAT_SAMSUNG_USB_PHY_H */
diff --git a/arch/arm/plat-samsung/include/plat/wakeup-mask.h b/arch/arm/plat-samsung/include/plat/wakeup-mask.h
new file mode 100644
index 000000000..43e4acd2e
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/wakeup-mask.h
@@ -0,0 +1,44 @@
+/* arch/arm/plat-samsung/include/plat/wakeup-mask.h
+ *
+ * Copyright 2010 Ben Dooks <ben-linux@fluff.org>
+ *
+ * Support for wakeup mask interrupts on newer SoCs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#ifndef __PLAT_WAKEUP_MASK_H
+#define __PLAT_WAKEUP_MASK_H __file__
+
+/* if no irq yet defined, but still want to mask */
+#define NO_WAKEUP_IRQ (0x90000000)
+
+/**
+ * struct samsung_wakeup_mask - wakeup mask information
+ * @irq: The interrupt associated with this wakeup.
+ * @bit: The bit, as a (1 << bitno) controlling this source.
+ */ 
+struct samsung_wakeup_mask {
+	unsigned int	irq;
+	u32		bit;
+};
+
+/**
+ * samsung_sync_wakemask - sync wakeup mask information for pm
+ * @reg: The register that is used.
+ * @masks: The list of masks to use.
+ * @nr_masks: The number of entries pointed to buy @masks.
+ *
+ * Synchronise the wakeup mask information at suspend time from the list
+ * of interrupts and control bits in @masks. We do this at suspend time
+ * as overriding the relevant irq chips is harder and the register is only
+ * required to be correct before we enter sleep.
+ */
+extern void samsung_sync_wakemask(void __iomem *reg,
+				  struct samsung_wakeup_mask *masks,
+				  int nr_masks);
+
+#endif /* __PLAT_WAKEUP_MASK_H */
diff --git a/arch/arm/plat-samsung/include/plat/watchdog-reset.h b/arch/arm/plat-samsung/include/plat/watchdog-reset.h
new file mode 100644
index 000000000..0386b8f76
--- /dev/null
+++ b/arch/arm/plat-samsung/include/plat/watchdog-reset.h
@@ -0,0 +1,20 @@
+/* arch/arm/plat-s3c/include/plat/watchdog-reset.h
+ *
+ * Copyright (c) 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2410 - System define for arch_reset() function
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __PLAT_SAMSUNG_WATCHDOG_RESET_H
+#define __PLAT_SAMSUNG_WATCHDOG_RESET_H
+
+extern void samsung_wdt_reset(void);
+extern void samsung_wdt_reset_of_init(void);
+extern void samsung_wdt_reset_init(void __iomem *base);
+
+#endif /* __PLAT_SAMSUNG_WATCHDOG_RESET_H */
diff --git a/arch/arm/plat-samsung/init.c b/arch/arm/plat-samsung/init.c
new file mode 100644
index 000000000..11fbbc26e
--- /dev/null
+++ b/arch/arm/plat-samsung/init.c
@@ -0,0 +1,173 @@
+/* linux/arch/arm/plat-s3c/init.c
+ *
+ * Copyright (c) 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C series CPU initialisation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/*
+ * NOTE: Code in this file is not used on S3C64xx when booting with
+ * Device Tree support.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <plat/cpu.h>
+#include <plat/devs.h>
+
+static struct cpu_table *cpu;
+
+static struct cpu_table * __init s3c_lookup_cpu(unsigned long idcode,
+						struct cpu_table *tab,
+						unsigned int count)
+{
+	for (; count != 0; count--, tab++) {
+		if ((idcode & tab->idmask) == (tab->idcode & tab->idmask))
+			return tab;
+	}
+
+	return NULL;
+}
+
+void __init s3c_init_cpu(unsigned long idcode,
+			 struct cpu_table *cputab, unsigned int cputab_size)
+{
+	cpu = s3c_lookup_cpu(idcode, cputab, cputab_size);
+
+	if (cpu == NULL) {
+		printk(KERN_ERR "Unknown CPU type 0x%08lx\n", idcode);
+		panic("Unknown S3C24XX CPU");
+	}
+
+	printk("CPU %s (id 0x%08lx)\n", cpu->name, idcode);
+
+	if (cpu->init == NULL) {
+		printk(KERN_ERR "CPU %s support not enabled\n", cpu->name);
+		panic("Unsupported Samsung CPU");
+	}
+
+	if (cpu->map_io)
+		cpu->map_io();
+}
+
+/* s3c24xx_init_clocks
+ *
+ * Initialise the clock subsystem and associated information from the
+ * given master crystal value.
+ *
+ * xtal  = 0 -> use default PLL crystal value (normally 12MHz)
+ *      != 0 -> PLL crystal value in Hz
+*/
+
+void __init s3c24xx_init_clocks(int xtal)
+{
+	if (xtal == 0)
+		xtal = 12*1000*1000;
+
+	if (cpu == NULL)
+		panic("s3c24xx_init_clocks: no cpu setup?\n");
+
+	if (cpu->init_clocks == NULL)
+		panic("s3c24xx_init_clocks: cpu has no clock init\n");
+	else
+		(cpu->init_clocks)(xtal);
+}
+
+/* uart management */
+#if IS_ENABLED(CONFIG_SAMSUNG_ATAGS)
+static int nr_uarts __initdata = 0;
+
+#ifdef CONFIG_SERIAL_SAMSUNG_UARTS
+static struct s3c2410_uartcfg uart_cfgs[CONFIG_SERIAL_SAMSUNG_UARTS];
+#endif
+
+/* s3c24xx_init_uartdevs
+ *
+ * copy the specified platform data and configuration into our central
+ * set of devices, before the data is thrown away after the init process.
+ *
+ * This also fills in the array passed to the serial driver for the
+ * early initialisation of the console.
+*/
+
+void __init s3c24xx_init_uartdevs(char *name,
+				  struct s3c24xx_uart_resources *res,
+				  struct s3c2410_uartcfg *cfg, int no)
+{
+#ifdef CONFIG_SERIAL_SAMSUNG_UARTS
+	struct platform_device *platdev;
+	struct s3c2410_uartcfg *cfgptr = uart_cfgs;
+	struct s3c24xx_uart_resources *resp;
+	int uart;
+
+	memcpy(cfgptr, cfg, sizeof(struct s3c2410_uartcfg) * no);
+
+	for (uart = 0; uart < no; uart++, cfg++, cfgptr++) {
+		platdev = s3c24xx_uart_src[cfgptr->hwport];
+
+		resp = res + cfgptr->hwport;
+
+		s3c24xx_uart_devs[uart] = platdev;
+
+		platdev->name = name;
+		platdev->resource = resp->resources;
+		platdev->num_resources = resp->nr_resources;
+
+		platdev->dev.platform_data = cfgptr;
+	}
+
+	nr_uarts = no;
+#endif
+}
+
+void __init s3c24xx_init_uarts(struct s3c2410_uartcfg *cfg, int no)
+{
+	if (cpu == NULL)
+		return;
+
+	if (cpu->init_uarts == NULL && IS_ENABLED(CONFIG_SAMSUNG_ATAGS)) {
+		printk(KERN_ERR "s3c24xx_init_uarts: cpu has no uart init\n");
+	} else
+		(cpu->init_uarts)(cfg, no);
+}
+#endif
+
+static int __init s3c_arch_init(void)
+{
+	int ret;
+
+	// do the correct init for cpu
+
+	if (cpu == NULL) {
+		/* Not needed when booting with device tree. */
+		if (of_have_populated_dt())
+			return 0;
+		panic("s3c_arch_init: NULL cpu\n");
+	}
+
+	ret = (cpu->init)();
+	if (ret != 0)
+		return ret;
+#if IS_ENABLED(CONFIG_SAMSUNG_ATAGS)
+	ret = platform_add_devices(s3c24xx_uart_devs, nr_uarts);
+#endif
+	return ret;
+}
+
+arch_initcall(s3c_arch_init);
diff --git a/arch/arm/plat-samsung/platformdata.c b/arch/arm/plat-samsung/platformdata.c
new file mode 100644
index 000000000..b430e9946
--- /dev/null
+++ b/arch/arm/plat-samsung/platformdata.c
@@ -0,0 +1,60 @@
+/* linux/arch/arm/plat-samsung/platformdata.c
+ *
+ * Copyright 2010 Ben Dooks <ben-linux <at> fluff.org>
+ *
+ * Helper for platform data setting
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+
+#include <plat/devs.h>
+#include <plat/sdhci.h>
+
+void __init *s3c_set_platdata(void *pd, size_t pdsize,
+			      struct platform_device *pdev)
+{
+	void *npd;
+
+	if (!pd) {
+		/* too early to use dev_name(), may not be registered */
+		printk(KERN_ERR "%s: no platform data supplied\n", pdev->name);
+		return NULL;
+	}
+
+	npd = kmemdup(pd, pdsize, GFP_KERNEL);
+	if (!npd) {
+		printk(KERN_ERR "%s: cannot clone platform data\n", pdev->name);
+		return NULL;
+	}
+
+	pdev->dev.platform_data = npd;
+	return npd;
+}
+
+void s3c_sdhci_set_platdata(struct s3c_sdhci_platdata *pd,
+			     struct s3c_sdhci_platdata *set)
+{
+	set->cd_type = pd->cd_type;
+	set->ext_cd_init = pd->ext_cd_init;
+	set->ext_cd_cleanup = pd->ext_cd_cleanup;
+	set->ext_cd_gpio = pd->ext_cd_gpio;
+	set->ext_cd_gpio_invert = pd->ext_cd_gpio_invert;
+
+	if (pd->max_width)
+		set->max_width = pd->max_width;
+	if (pd->cfg_gpio)
+		set->cfg_gpio = pd->cfg_gpio;
+	if (pd->host_caps)
+		set->host_caps |= pd->host_caps;
+	if (pd->host_caps2)
+		set->host_caps2 |= pd->host_caps2;
+	if (pd->pm_caps)
+		set->pm_caps |= pd->pm_caps;
+}
diff --git a/arch/arm/plat-samsung/pm-check.c b/arch/arm/plat-samsung/pm-check.c
new file mode 100644
index 000000000..04aff2c31
--- /dev/null
+++ b/arch/arm/plat-samsung/pm-check.c
@@ -0,0 +1,237 @@
+/* linux/arch/arm/plat-s3c/pm-check.c
+ *  originally in linux/arch/arm/plat-s3c24xx/pm.c
+ *
+ * Copyright (c) 2004-2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C Power Mangament - suspend/resume memory corruptiuon check.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/suspend.h>
+#include <linux/init.h>
+#include <linux/crc32.h>
+#include <linux/ioport.h>
+#include <linux/slab.h>
+
+#include <plat/pm-common.h>
+
+#if CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE < 1
+#error CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE must be a positive non-zero value
+#endif
+
+/* suspend checking code...
+ *
+ * this next area does a set of crc checks over all the installed
+ * memory, so the system can verify if the resume was ok.
+ *
+ * CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE defines the block-size for the CRC,
+ * increasing it will mean that the area corrupted will be less easy to spot,
+ * and reducing the size will cause the CRC save area to grow
+*/
+
+#define CHECK_CHUNKSIZE (CONFIG_SAMSUNG_PM_CHECK_CHUNKSIZE * 1024)
+
+static u32 crc_size;	/* size needed for the crc block */
+static u32 *crcs;	/* allocated over suspend/resume */
+
+typedef u32 *(run_fn_t)(struct resource *ptr, u32 *arg);
+
+/* s3c_pm_run_res
+ *
+ * go through the given resource list, and look for system ram
+*/
+
+static void s3c_pm_run_res(struct resource *ptr, run_fn_t fn, u32 *arg)
+{
+	while (ptr != NULL) {
+		if (ptr->child != NULL)
+			s3c_pm_run_res(ptr->child, fn, arg);
+
+		if ((ptr->flags & IORESOURCE_MEM) &&
+		    strcmp(ptr->name, "System RAM") == 0) {
+			S3C_PMDBG("Found system RAM at %08lx..%08lx\n",
+				  (unsigned long)ptr->start,
+				  (unsigned long)ptr->end);
+			arg = (fn)(ptr, arg);
+		}
+
+		ptr = ptr->sibling;
+	}
+}
+
+static void s3c_pm_run_sysram(run_fn_t fn, u32 *arg)
+{
+	s3c_pm_run_res(&iomem_resource, fn, arg);
+}
+
+static u32 *s3c_pm_countram(struct resource *res, u32 *val)
+{
+	u32 size = (u32)resource_size(res);
+
+	size += CHECK_CHUNKSIZE-1;
+	size /= CHECK_CHUNKSIZE;
+
+	S3C_PMDBG("Area %08lx..%08lx, %d blocks\n",
+		  (unsigned long)res->start, (unsigned long)res->end, size);
+
+	*val += size * sizeof(u32);
+	return val;
+}
+
+/* s3c_pm_prepare_check
+ *
+ * prepare the necessary information for creating the CRCs. This
+ * must be done before the final save, as it will require memory
+ * allocating, and thus touching bits of the kernel we do not
+ * know about.
+*/
+
+void s3c_pm_check_prepare(void)
+{
+	crc_size = 0;
+
+	s3c_pm_run_sysram(s3c_pm_countram, &crc_size);
+
+	S3C_PMDBG("s3c_pm_prepare_check: %u checks needed\n", crc_size);
+
+	crcs = kmalloc(crc_size+4, GFP_KERNEL);
+	if (crcs == NULL)
+		printk(KERN_ERR "Cannot allocated CRC save area\n");
+}
+
+static u32 *s3c_pm_makecheck(struct resource *res, u32 *val)
+{
+	unsigned long addr, left;
+
+	for (addr = res->start; addr < res->end;
+	     addr += CHECK_CHUNKSIZE) {
+		left = res->end - addr;
+
+		if (left > CHECK_CHUNKSIZE)
+			left = CHECK_CHUNKSIZE;
+
+		*val = crc32_le(~0, phys_to_virt(addr), left);
+		val++;
+	}
+
+	return val;
+}
+
+/* s3c_pm_check_store
+ *
+ * compute the CRC values for the memory blocks before the final
+ * sleep.
+*/
+
+void s3c_pm_check_store(void)
+{
+	if (crcs != NULL)
+		s3c_pm_run_sysram(s3c_pm_makecheck, crcs);
+}
+
+/* in_region
+ *
+ * return TRUE if the area defined by ptr..ptr+size contains the
+ * what..what+whatsz
+*/
+
+static inline int in_region(void *ptr, int size, void *what, size_t whatsz)
+{
+	if ((what+whatsz) < ptr)
+		return 0;
+
+	if (what > (ptr+size))
+		return 0;
+
+	return 1;
+}
+
+/**
+ * s3c_pm_runcheck() - helper to check a resource on restore.
+ * @res: The resource to check
+ * @vak: Pointer to list of CRC32 values to check.
+ *
+ * Called from the s3c_pm_check_restore() via s3c_pm_run_sysram(), this
+ * function runs the given memory resource checking it against the stored
+ * CRC to ensure that memory is restored. The function tries to skip as
+ * many of the areas used during the suspend process.
+ */
+static u32 *s3c_pm_runcheck(struct resource *res, u32 *val)
+{
+	unsigned long addr;
+	unsigned long left;
+	void *stkpage;
+	void *ptr;
+	u32 calc;
+
+	stkpage = (void *)((u32)&calc & ~PAGE_MASK);
+
+	for (addr = res->start; addr < res->end;
+	     addr += CHECK_CHUNKSIZE) {
+		left = res->end - addr;
+
+		if (left > CHECK_CHUNKSIZE)
+			left = CHECK_CHUNKSIZE;
+
+		ptr = phys_to_virt(addr);
+
+		if (in_region(ptr, left, stkpage, 4096)) {
+			S3C_PMDBG("skipping %08lx, has stack in\n", addr);
+			goto skip_check;
+		}
+
+		if (in_region(ptr, left, crcs, crc_size)) {
+			S3C_PMDBG("skipping %08lx, has crc block in\n", addr);
+			goto skip_check;
+		}
+
+		/* calculate and check the checksum */
+
+		calc = crc32_le(~0, ptr, left);
+		if (calc != *val) {
+			printk(KERN_ERR "Restore CRC error at "
+			       "%08lx (%08x vs %08x)\n", addr, calc, *val);
+
+			S3C_PMDBG("Restore CRC error at %08lx (%08x vs %08x)\n",
+			    addr, calc, *val);
+		}
+
+	skip_check:
+		val++;
+	}
+
+	return val;
+}
+
+/**
+ * s3c_pm_check_restore() - memory check called on resume
+ *
+ * check the CRCs after the restore event and free the memory used
+ * to hold them
+*/
+void s3c_pm_check_restore(void)
+{
+	if (crcs != NULL)
+		s3c_pm_run_sysram(s3c_pm_runcheck, crcs);
+}
+
+/**
+ * s3c_pm_check_cleanup() - free memory resources
+ *
+ * Free the resources that where allocated by the suspend
+ * memory check code. We do this separately from the
+ * s3c_pm_check_restore() function as we cannot call any
+ * functions that might sleep during that resume.
+ */
+void s3c_pm_check_cleanup(void)
+{
+	kfree(crcs);
+	crcs = NULL;
+}
+
diff --git a/arch/arm/plat-samsung/pm-common.c b/arch/arm/plat-samsung/pm-common.c
new file mode 100644
index 000000000..515cd5337
--- /dev/null
+++ b/arch/arm/plat-samsung/pm-common.c
@@ -0,0 +1,75 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ *	Tomasz Figa <t.figa@samsung.com>
+ * Copyright (C) 2008 Openmoko, Inc.
+ * Copyright (C) 2004-2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * Samsung common power management helper functions.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+
+#include <plat/pm-common.h>
+
+/* helper functions to save and restore register state */
+
+/**
+ * s3c_pm_do_save() - save a set of registers for restoration on resume.
+ * @ptr: Pointer to an array of registers.
+ * @count: Size of the ptr array.
+ *
+ * Run through the list of registers given, saving their contents in the
+ * array for later restoration when we wakeup.
+ */
+void s3c_pm_do_save(struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++) {
+		ptr->val = __raw_readl(ptr->reg);
+		S3C_PMDBG("saved %p value %08lx\n", ptr->reg, ptr->val);
+	}
+}
+
+/**
+ * s3c_pm_do_restore() - restore register values from the save list.
+ * @ptr: Pointer to an array of registers.
+ * @count: Size of the ptr array.
+ *
+ * Restore the register values saved from s3c_pm_do_save().
+ *
+ * Note, we do not use S3C_PMDBG() in here, as the system may not have
+ * restore the UARTs state yet
+*/
+
+void s3c_pm_do_restore(const struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++) {
+		pr_debug("restore %p (restore %08lx, was %08x)\n",
+				ptr->reg, ptr->val, __raw_readl(ptr->reg));
+
+		__raw_writel(ptr->val, ptr->reg);
+	}
+}
+
+/**
+ * s3c_pm_do_restore_core() - early restore register values from save list.
+ *
+ * This is similar to s3c_pm_do_restore() except we try and minimise the
+ * side effects of the function in case registers that hardware might need
+ * to work has been restored.
+ *
+ * WARNING: Do not put any debug in here that may effect memory or use
+ * peripherals, as things may be changing!
+*/
+
+void s3c_pm_do_restore_core(const struct sleep_save *ptr, int count)
+{
+	for (; count > 0; count--, ptr++)
+		__raw_writel(ptr->val, ptr->reg);
+}
diff --git a/arch/arm/plat-samsung/pm-debug.c b/arch/arm/plat-samsung/pm-debug.c
new file mode 100644
index 000000000..64e15da33
--- /dev/null
+++ b/arch/arm/plat-samsung/pm-debug.c
@@ -0,0 +1,99 @@
+/*
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ *	Tomasz Figa <t.figa@samsung.com>
+ * Copyright (C) 2008 Openmoko, Inc.
+ * Copyright (C) 2004-2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * Samsung common power management (suspend to RAM) debug support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/serial_core.h>
+#include <linux/serial_s3c.h>
+#include <linux/io.h>
+
+#include <asm/mach/map.h>
+
+#include <plat/cpu.h>
+#include <plat/pm-common.h>
+
+#ifdef CONFIG_SAMSUNG_ATAGS
+#include <plat/pm.h>
+#include <mach/pm-core.h>
+#else
+static inline void s3c_pm_debug_init_uart(void) {}
+static inline void s3c_pm_arch_update_uart(void __iomem *regs,
+					   struct pm_uart_save *save) {}
+#endif
+
+static struct pm_uart_save uart_save;
+
+extern void printascii(const char *);
+
+void s3c_pm_dbg(const char *fmt, ...)
+{
+	va_list va;
+	char buff[256];
+
+	va_start(va, fmt);
+	vsnprintf(buff, sizeof(buff), fmt, va);
+	va_end(va);
+
+	printascii(buff);
+}
+
+void s3c_pm_debug_init(void)
+{
+	/* restart uart clocks so we can use them to output */
+	s3c_pm_debug_init_uart();
+}
+
+static inline void __iomem *s3c_pm_uart_base(void)
+{
+	unsigned long paddr;
+	unsigned long vaddr;
+
+	debug_ll_addr(&paddr, &vaddr);
+
+	return (void __iomem *)vaddr;
+}
+
+void s3c_pm_save_uarts(void)
+{
+	void __iomem *regs = s3c_pm_uart_base();
+	struct pm_uart_save *save = &uart_save;
+
+	save->ulcon = __raw_readl(regs + S3C2410_ULCON);
+	save->ucon = __raw_readl(regs + S3C2410_UCON);
+	save->ufcon = __raw_readl(regs + S3C2410_UFCON);
+	save->umcon = __raw_readl(regs + S3C2410_UMCON);
+	save->ubrdiv = __raw_readl(regs + S3C2410_UBRDIV);
+
+	if (!soc_is_s3c2410())
+		save->udivslot = __raw_readl(regs + S3C2443_DIVSLOT);
+
+	S3C_PMDBG("UART[%p]: ULCON=%04x, UCON=%04x, UFCON=%04x, UBRDIV=%04x\n",
+		  regs, save->ulcon, save->ucon, save->ufcon, save->ubrdiv);
+}
+
+void s3c_pm_restore_uarts(void)
+{
+	void __iomem *regs = s3c_pm_uart_base();
+	struct pm_uart_save *save = &uart_save;
+
+	s3c_pm_arch_update_uart(regs, save);
+
+	__raw_writel(save->ulcon, regs + S3C2410_ULCON);
+	__raw_writel(save->ucon,  regs + S3C2410_UCON);
+	__raw_writel(save->ufcon, regs + S3C2410_UFCON);
+	__raw_writel(save->umcon, regs + S3C2410_UMCON);
+	__raw_writel(save->ubrdiv, regs + S3C2410_UBRDIV);
+
+	if (!soc_is_s3c2410())
+		__raw_writel(save->udivslot, regs + S3C2443_DIVSLOT);
+}
diff --git a/arch/arm/plat-samsung/pm-gpio.c b/arch/arm/plat-samsung/pm-gpio.c
new file mode 100644
index 000000000..f9a09262f
--- /dev/null
+++ b/arch/arm/plat-samsung/pm-gpio.c
@@ -0,0 +1,386 @@
+
+/* linux/arch/arm/plat-s3c/pm-gpio.c
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C series GPIO PM code
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+
+#include <mach/gpio-samsung.h>
+
+#include <plat/gpio-core.h>
+#include <plat/pm.h>
+
+/* PM GPIO helpers */
+
+#define OFFS_CON	(0x00)
+#define OFFS_DAT	(0x04)
+#define OFFS_UP		(0x08)
+
+static void samsung_gpio_pm_1bit_save(struct samsung_gpio_chip *chip)
+{
+	chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON);
+	chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT);
+}
+
+static void samsung_gpio_pm_1bit_resume(struct samsung_gpio_chip *chip)
+{
+	void __iomem *base = chip->base;
+	u32 old_gpcon = __raw_readl(base + OFFS_CON);
+	u32 old_gpdat = __raw_readl(base + OFFS_DAT);
+	u32 gps_gpcon = chip->pm_save[0];
+	u32 gps_gpdat = chip->pm_save[1];
+	u32 gpcon;
+
+	/* GPACON only has one bit per control / data and no PULLUPs.
+	 * GPACON[x] = 0 => Output, 1 => SFN */
+
+	/* first set all SFN bits to SFN */
+
+	gpcon = old_gpcon | gps_gpcon;
+	__raw_writel(gpcon, base + OFFS_CON);
+
+	/* now set all the other bits */
+
+	__raw_writel(gps_gpdat, base + OFFS_DAT);
+	__raw_writel(gps_gpcon, base + OFFS_CON);
+
+	S3C_PMDBG("%s: CON %08x => %08x, DAT %08x => %08x\n",
+		  chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat);
+}
+
+struct samsung_gpio_pm samsung_gpio_pm_1bit = {
+	.save	= samsung_gpio_pm_1bit_save,
+	.resume = samsung_gpio_pm_1bit_resume,
+};
+
+static void samsung_gpio_pm_2bit_save(struct samsung_gpio_chip *chip)
+{
+	chip->pm_save[0] = __raw_readl(chip->base + OFFS_CON);
+	chip->pm_save[1] = __raw_readl(chip->base + OFFS_DAT);
+	chip->pm_save[2] = __raw_readl(chip->base + OFFS_UP);
+}
+
+/* Test whether the given masked+shifted bits of an GPIO configuration
+ * are one of the SFN (special function) modes. */
+
+static inline int is_sfn(unsigned long con)
+{
+	return con >= 2;
+}
+
+/* Test if the given masked+shifted GPIO configuration is an input */
+
+static inline int is_in(unsigned long con)
+{
+	return con == 0;
+}
+
+/* Test if the given masked+shifted GPIO configuration is an output */
+
+static inline int is_out(unsigned long con)
+{
+	return con == 1;
+}
+
+/**
+ * samsung_gpio_pm_2bit_resume() - restore the given GPIO bank
+ * @chip: The chip information to resume.
+ *
+ * Restore one of the GPIO banks that was saved during suspend. This is
+ * not as simple as once thought, due to the possibility of glitches
+ * from the order that the CON and DAT registers are set in.
+ *
+ * The three states the pin can be are {IN,OUT,SFN} which gives us 9
+ * combinations of changes to check. Three of these, if the pin stays
+ * in the same configuration can be discounted. This leaves us with
+ * the following:
+ *
+ * { IN => OUT }  Change DAT first
+ * { IN => SFN }  Change CON first
+ * { OUT => SFN } Change CON first, so new data will not glitch
+ * { OUT => IN }  Change CON first, so new data will not glitch
+ * { SFN => IN }  Change CON first
+ * { SFN => OUT } Change DAT first, so new data will not glitch [1]
+ *
+ * We do not currently deal with the UP registers as these control
+ * weak resistors, so a small delay in change should not need to bring
+ * these into the calculations.
+ *
+ * [1] this assumes that writing to a pin DAT whilst in SFN will set the
+ *     state for when it is next output.
+ */
+static void samsung_gpio_pm_2bit_resume(struct samsung_gpio_chip *chip)
+{
+	void __iomem *base = chip->base;
+	u32 old_gpcon = __raw_readl(base + OFFS_CON);
+	u32 old_gpdat = __raw_readl(base + OFFS_DAT);
+	u32 gps_gpcon = chip->pm_save[0];
+	u32 gps_gpdat = chip->pm_save[1];
+	u32 gpcon, old, new, mask;
+	u32 change_mask = 0x0;
+	int nr;
+
+	/* restore GPIO pull-up settings */
+	__raw_writel(chip->pm_save[2], base + OFFS_UP);
+
+	/* Create a change_mask of all the items that need to have
+	 * their CON value changed before their DAT value, so that
+	 * we minimise the work between the two settings.
+	 */
+
+	for (nr = 0, mask = 0x03; nr < 32; nr += 2, mask <<= 2) {
+		old = (old_gpcon & mask) >> nr;
+		new = (gps_gpcon & mask) >> nr;
+
+		/* If there is no change, then skip */
+
+		if (old == new)
+			continue;
+
+		/* If both are special function, then skip */
+
+		if (is_sfn(old) && is_sfn(new))
+			continue;
+
+		/* Change is IN => OUT, do not change now */
+
+		if (is_in(old) && is_out(new))
+			continue;
+
+		/* Change is SFN => OUT, do not change now */
+
+		if (is_sfn(old) && is_out(new))
+			continue;
+
+		/* We should now be at the case of IN=>SFN,
+		 * OUT=>SFN, OUT=>IN, SFN=>IN. */
+
+		change_mask |= mask;
+	}
+
+
+	/* Write the new CON settings */
+
+	gpcon = old_gpcon & ~change_mask;
+	gpcon |= gps_gpcon & change_mask;
+
+	__raw_writel(gpcon, base + OFFS_CON);
+
+	/* Now change any items that require DAT,CON */
+
+	__raw_writel(gps_gpdat, base + OFFS_DAT);
+	__raw_writel(gps_gpcon, base + OFFS_CON);
+
+	S3C_PMDBG("%s: CON %08x => %08x, DAT %08x => %08x\n",
+		  chip->chip.label, old_gpcon, gps_gpcon, old_gpdat, gps_gpdat);
+}
+
+struct samsung_gpio_pm samsung_gpio_pm_2bit = {
+	.save	= samsung_gpio_pm_2bit_save,
+	.resume = samsung_gpio_pm_2bit_resume,
+};
+
+#if defined(CONFIG_ARCH_S3C64XX)
+static void samsung_gpio_pm_4bit_save(struct samsung_gpio_chip *chip)
+{
+	chip->pm_save[1] = __raw_readl(chip->base + OFFS_CON);
+	chip->pm_save[2] = __raw_readl(chip->base + OFFS_DAT);
+	chip->pm_save[3] = __raw_readl(chip->base + OFFS_UP);
+
+	if (chip->chip.ngpio > 8)
+		chip->pm_save[0] = __raw_readl(chip->base - 4);
+}
+
+static u32 samsung_gpio_pm_4bit_mask(u32 old_gpcon, u32 gps_gpcon)
+{
+	u32 old, new, mask;
+	u32 change_mask = 0x0;
+	int nr;
+
+	for (nr = 0, mask = 0x0f; nr < 16; nr += 4, mask <<= 4) {
+		old = (old_gpcon & mask) >> nr;
+		new = (gps_gpcon & mask) >> nr;
+
+		/* If there is no change, then skip */
+
+		if (old == new)
+			continue;
+
+		/* If both are special function, then skip */
+
+		if (is_sfn(old) && is_sfn(new))
+			continue;
+
+		/* Change is IN => OUT, do not change now */
+
+		if (is_in(old) && is_out(new))
+			continue;
+
+		/* Change is SFN => OUT, do not change now */
+
+		if (is_sfn(old) && is_out(new))
+			continue;
+
+		/* We should now be at the case of IN=>SFN,
+		 * OUT=>SFN, OUT=>IN, SFN=>IN. */
+
+		change_mask |= mask;
+	}
+
+	return change_mask;
+}
+
+static void samsung_gpio_pm_4bit_con(struct samsung_gpio_chip *chip, int index)
+{
+	void __iomem *con = chip->base + (index * 4);
+	u32 old_gpcon = __raw_readl(con);
+	u32 gps_gpcon = chip->pm_save[index + 1];
+	u32 gpcon, mask;
+
+	mask = samsung_gpio_pm_4bit_mask(old_gpcon, gps_gpcon);
+
+	gpcon = old_gpcon & ~mask;
+	gpcon |= gps_gpcon & mask;
+
+	__raw_writel(gpcon, con);
+}
+
+static void samsung_gpio_pm_4bit_resume(struct samsung_gpio_chip *chip)
+{
+	void __iomem *base = chip->base;
+	u32 old_gpcon[2];
+	u32 old_gpdat = __raw_readl(base + OFFS_DAT);
+	u32 gps_gpdat = chip->pm_save[2];
+
+	/* First, modify the CON settings */
+
+	old_gpcon[0] = 0;
+	old_gpcon[1] = __raw_readl(base + OFFS_CON);
+
+	samsung_gpio_pm_4bit_con(chip, 0);
+	if (chip->chip.ngpio > 8) {
+		old_gpcon[0] = __raw_readl(base - 4);
+		samsung_gpio_pm_4bit_con(chip, -1);
+	}
+
+	/* Now change the configurations that require DAT,CON */
+
+	__raw_writel(chip->pm_save[2], base + OFFS_DAT);
+	__raw_writel(chip->pm_save[1], base + OFFS_CON);
+	if (chip->chip.ngpio > 8)
+		__raw_writel(chip->pm_save[0], base - 4);
+
+	__raw_writel(chip->pm_save[2], base + OFFS_DAT);
+	__raw_writel(chip->pm_save[3], base + OFFS_UP);
+
+	if (chip->chip.ngpio > 8) {
+		S3C_PMDBG("%s: CON4 %08x,%08x => %08x,%08x, DAT %08x => %08x\n",
+			  chip->chip.label, old_gpcon[0], old_gpcon[1],
+			  __raw_readl(base - 4),
+			  __raw_readl(base + OFFS_CON),
+			  old_gpdat, gps_gpdat);
+	} else
+		S3C_PMDBG("%s: CON4 %08x => %08x, DAT %08x => %08x\n",
+			  chip->chip.label, old_gpcon[1],
+			  __raw_readl(base + OFFS_CON),
+			  old_gpdat, gps_gpdat);
+}
+
+struct samsung_gpio_pm samsung_gpio_pm_4bit = {
+	.save	= samsung_gpio_pm_4bit_save,
+	.resume = samsung_gpio_pm_4bit_resume,
+};
+#endif /* CONFIG_ARCH_S3C64XX */
+
+/**
+ * samsung_pm_save_gpio() - save gpio chip data for suspend
+ * @ourchip: The chip for suspend.
+ */
+static void samsung_pm_save_gpio(struct samsung_gpio_chip *ourchip)
+{
+	struct samsung_gpio_pm *pm = ourchip->pm;
+
+	if (pm == NULL || pm->save == NULL)
+		S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label);
+	else
+		pm->save(ourchip);
+}
+
+/**
+ * samsung_pm_save_gpios() - Save the state of the GPIO banks.
+ *
+ * For all the GPIO banks, save the state of each one ready for going
+ * into a suspend mode.
+ */
+void samsung_pm_save_gpios(void)
+{
+	struct samsung_gpio_chip *ourchip;
+	unsigned int gpio_nr;
+
+	for (gpio_nr = 0; gpio_nr < S3C_GPIO_END;) {
+		ourchip = samsung_gpiolib_getchip(gpio_nr);
+		if (!ourchip) {
+			gpio_nr++;
+			continue;
+		}
+
+		samsung_pm_save_gpio(ourchip);
+
+		S3C_PMDBG("%s: save %08x,%08x,%08x,%08x\n",
+			  ourchip->chip.label,
+			  ourchip->pm_save[0],
+			  ourchip->pm_save[1],
+			  ourchip->pm_save[2],
+			  ourchip->pm_save[3]);
+
+		gpio_nr += ourchip->chip.ngpio;
+		gpio_nr += CONFIG_S3C_GPIO_SPACE;
+	}
+}
+
+/**
+ * samsung_pm_resume_gpio() - restore gpio chip data after suspend
+ * @ourchip: The suspended chip.
+ */
+static void samsung_pm_resume_gpio(struct samsung_gpio_chip *ourchip)
+{
+	struct samsung_gpio_pm *pm = ourchip->pm;
+
+	if (pm == NULL || pm->resume == NULL)
+		S3C_PMDBG("%s: no pm for %s\n", __func__, ourchip->chip.label);
+	else
+		pm->resume(ourchip);
+}
+
+void samsung_pm_restore_gpios(void)
+{
+	struct samsung_gpio_chip *ourchip;
+	unsigned int gpio_nr;
+
+	for (gpio_nr = 0; gpio_nr < S3C_GPIO_END;) {
+		ourchip = samsung_gpiolib_getchip(gpio_nr);
+		if (!ourchip) {
+			gpio_nr++;
+			continue;
+		}
+
+		samsung_pm_resume_gpio(ourchip);
+
+		gpio_nr += ourchip->chip.ngpio;
+		gpio_nr += CONFIG_S3C_GPIO_SPACE;
+	}
+}
diff --git a/arch/arm/plat-samsung/pm.c b/arch/arm/plat-samsung/pm.c
new file mode 100644
index 000000000..82777c649
--- /dev/null
+++ b/arch/arm/plat-samsung/pm.c
@@ -0,0 +1,208 @@
+/* linux/arch/arm/plat-s3c/pm.c
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2004-2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C common power management (suspend to ram) support.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/init.h>
+#include <linux/suspend.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/of.h>
+#include <linux/serial_s3c.h>
+#include <linux/io.h>
+
+#include <asm/cacheflush.h>
+#include <asm/suspend.h>
+
+#ifdef CONFIG_SAMSUNG_ATAGS
+#include <mach/map.h>
+#ifndef CONFIG_ARCH_EXYNOS
+#include <mach/regs-clock.h>
+#include <mach/regs-irq.h>
+#endif
+#include <mach/irqs.h>
+#endif
+
+#include <asm/irq.h>
+
+#include <plat/pm.h>
+#include <mach/pm-core.h>
+
+/* for external use */
+
+unsigned long s3c_pm_flags;
+
+/* The IRQ ext-int code goes here, it is too small to currently bother
+ * with its own file. */
+
+unsigned long s3c_irqwake_intmask	= 0xffffffffL;
+unsigned long s3c_irqwake_eintmask	= 0xffffffffL;
+
+int s3c_irqext_wake(struct irq_data *data, unsigned int state)
+{
+	unsigned long bit = 1L << IRQ_EINT_BIT(data->irq);
+
+	if (!(s3c_irqwake_eintallow & bit))
+		return -ENOENT;
+
+	printk(KERN_INFO "wake %s for irq %d\n",
+	       state ? "enabled" : "disabled", data->irq);
+
+	if (!state)
+		s3c_irqwake_eintmask |= bit;
+	else
+		s3c_irqwake_eintmask &= ~bit;
+
+	return 0;
+}
+
+void (*pm_cpu_prep)(void);
+int (*pm_cpu_sleep)(unsigned long);
+
+#define any_allowed(mask, allow) (((mask) & (allow)) != (allow))
+
+/* s3c_pm_enter
+ *
+ * central control for sleep/resume process
+*/
+
+static int s3c_pm_enter(suspend_state_t state)
+{
+	int ret;
+	/* ensure the debug is initialised (if enabled) */
+
+	s3c_pm_debug_init();
+
+	S3C_PMDBG("%s(%d)\n", __func__, state);
+
+	if (pm_cpu_prep == NULL || pm_cpu_sleep == NULL) {
+		printk(KERN_ERR "%s: error: no cpu sleep function\n", __func__);
+		return -EINVAL;
+	}
+
+	/* check if we have anything to wake-up with... bad things seem
+	 * to happen if you suspend with no wakeup (system will often
+	 * require a full power-cycle)
+	*/
+
+	if (!of_have_populated_dt() &&
+	    !any_allowed(s3c_irqwake_intmask, s3c_irqwake_intallow) &&
+	    !any_allowed(s3c_irqwake_eintmask, s3c_irqwake_eintallow)) {
+		printk(KERN_ERR "%s: No wake-up sources!\n", __func__);
+		printk(KERN_ERR "%s: Aborting sleep\n", __func__);
+		return -EINVAL;
+	}
+
+	/* save all necessary core registers not covered by the drivers */
+
+	if (!of_have_populated_dt()) {
+		samsung_pm_save_gpios();
+		samsung_pm_saved_gpios();
+	}
+
+	s3c_pm_save_uarts();
+	s3c_pm_save_core();
+
+	/* set the irq configuration for wake */
+
+	s3c_pm_configure_extint();
+
+	S3C_PMDBG("sleep: irq wakeup masks: %08lx,%08lx\n",
+	    s3c_irqwake_intmask, s3c_irqwake_eintmask);
+
+	s3c_pm_arch_prepare_irqs();
+
+	/* call cpu specific preparation */
+
+	pm_cpu_prep();
+
+	/* flush cache back to ram */
+
+	flush_cache_all();
+
+	s3c_pm_check_store();
+
+	/* send the cpu to sleep... */
+
+	s3c_pm_arch_stop_clocks();
+
+	/* this will also act as our return point from when
+	 * we resume as it saves its own register state and restores it
+	 * during the resume.  */
+
+	ret = cpu_suspend(0, pm_cpu_sleep);
+	if (ret)
+		return ret;
+
+	/* restore the system state */
+
+	s3c_pm_restore_core();
+	s3c_pm_restore_uarts();
+
+	if (!of_have_populated_dt()) {
+		samsung_pm_restore_gpios();
+		s3c_pm_restored_gpios();
+	}
+
+	s3c_pm_debug_init();
+
+	/* check what irq (if any) restored the system */
+
+	s3c_pm_arch_show_resume_irqs();
+
+	S3C_PMDBG("%s: post sleep, preparing to return\n", __func__);
+
+	/* LEDs should now be 1110 */
+	s3c_pm_debug_smdkled(1 << 1, 0);
+
+	s3c_pm_check_restore();
+
+	/* ok, let's return from sleep */
+
+	S3C_PMDBG("S3C PM Resume (post-restore)\n");
+	return 0;
+}
+
+static int s3c_pm_prepare(void)
+{
+	/* prepare check area if configured */
+
+	s3c_pm_check_prepare();
+	return 0;
+}
+
+static void s3c_pm_finish(void)
+{
+	s3c_pm_check_cleanup();
+}
+
+static const struct platform_suspend_ops s3c_pm_ops = {
+	.enter		= s3c_pm_enter,
+	.prepare	= s3c_pm_prepare,
+	.finish		= s3c_pm_finish,
+	.valid		= suspend_valid_only_mem,
+};
+
+/* s3c_pm_init
+ *
+ * Attach the power management functions. This should be called
+ * from the board specific initialisation if the board supports
+ * it.
+*/
+
+int __init s3c_pm_init(void)
+{
+	printk("S3C Power Management, Copyright 2004 Simtec Electronics\n");
+
+	suspend_set_ops(&s3c_pm_ops);
+	return 0;
+}
diff --git a/arch/arm/plat-samsung/s5p-dev-mfc.c b/arch/arm/plat-samsung/s5p-dev-mfc.c
new file mode 100644
index 000000000..0b04b6b0f
--- /dev/null
+++ b/arch/arm/plat-samsung/s5p-dev-mfc.c
@@ -0,0 +1,94 @@
+/*
+ * Copyright (C) 2010-2011 Samsung Electronics Co.Ltd
+ *
+ * Base S5P MFC resource and device definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/memblock.h>
+#include <linux/ioport.h>
+#include <linux/of_fdt.h>
+#include <linux/of.h>
+
+static struct platform_device s5p_device_mfc_l;
+static struct platform_device s5p_device_mfc_r;
+
+struct s5p_mfc_dt_meminfo {
+	unsigned long	loff;
+	unsigned long	lsize;
+	unsigned long	roff;
+	unsigned long	rsize;
+	char		*compatible;
+};
+
+struct s5p_mfc_reserved_mem {
+	phys_addr_t	base;
+	unsigned long	size;
+	struct device	*dev;
+};
+
+static struct s5p_mfc_reserved_mem s5p_mfc_mem[2] __initdata;
+
+
+static void __init s5p_mfc_reserve_mem(phys_addr_t rbase, unsigned int rsize,
+				phys_addr_t lbase, unsigned int lsize)
+{
+	int i;
+
+	s5p_mfc_mem[0].dev = &s5p_device_mfc_r.dev;
+	s5p_mfc_mem[0].base = rbase;
+	s5p_mfc_mem[0].size = rsize;
+
+	s5p_mfc_mem[1].dev = &s5p_device_mfc_l.dev;
+	s5p_mfc_mem[1].base = lbase;
+	s5p_mfc_mem[1].size = lsize;
+
+	for (i = 0; i < ARRAY_SIZE(s5p_mfc_mem); i++) {
+		struct s5p_mfc_reserved_mem *area = &s5p_mfc_mem[i];
+		if (memblock_remove(area->base, area->size)) {
+			printk(KERN_ERR "Failed to reserve memory for MFC device (%ld bytes at 0x%08lx)\n",
+			       area->size, (unsigned long) area->base);
+			area->base = 0;
+		}
+	}
+}
+
+int __init s5p_fdt_alloc_mfc_mem(unsigned long node, const char *uname,
+				int depth, void *data)
+{
+	const __be32 *prop;
+	int len;
+	struct s5p_mfc_dt_meminfo mfc_mem;
+
+	if (!data)
+		return 0;
+
+	if (!of_flat_dt_is_compatible(node, data))
+		return 0;
+
+	prop = of_get_flat_dt_prop(node, "samsung,mfc-l", &len);
+	if (!prop || (len != 2 * sizeof(unsigned long)))
+		return 0;
+
+	mfc_mem.loff = be32_to_cpu(prop[0]);
+	mfc_mem.lsize = be32_to_cpu(prop[1]);
+
+	prop = of_get_flat_dt_prop(node, "samsung,mfc-r", &len);
+	if (!prop || (len != 2 * sizeof(unsigned long)))
+		return 0;
+
+	mfc_mem.roff = be32_to_cpu(prop[0]);
+	mfc_mem.rsize = be32_to_cpu(prop[1]);
+
+	s5p_mfc_reserve_mem(mfc_mem.roff, mfc_mem.rsize,
+			mfc_mem.loff, mfc_mem.lsize);
+
+	return 1;
+}
diff --git a/arch/arm/plat-samsung/setup-camif.c b/arch/arm/plat-samsung/setup-camif.c
new file mode 100644
index 000000000..72d8edb89
--- /dev/null
+++ b/arch/arm/plat-samsung/setup-camif.c
@@ -0,0 +1,71 @@
+/*
+ * Copyright (C) 2012 Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
+ *
+ * Helper functions for S3C24XX/S3C64XX SoC series CAMIF driver
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <plat/gpio-cfg.h>
+#include <mach/gpio-samsung.h>
+
+/* Number of camera port pins, without FIELD */
+#define S3C_CAMIF_NUM_GPIOS	13
+
+/* Default camera port configuration helpers. */
+
+static void camif_get_gpios(int *gpio_start, int *gpio_reset)
+{
+#ifdef CONFIG_ARCH_S3C24XX
+	*gpio_start = S3C2410_GPJ(0);
+	*gpio_reset = S3C2410_GPJ(12);
+#else
+	/* s3c64xx */
+	*gpio_start = S3C64XX_GPF(0);
+	*gpio_reset = S3C64XX_GPF(3);
+#endif
+}
+
+int s3c_camif_gpio_get(void)
+{
+	int gpio_start, gpio_reset;
+	int ret, i;
+
+	camif_get_gpios(&gpio_start, &gpio_reset);
+
+	for (i = 0; i < S3C_CAMIF_NUM_GPIOS; i++) {
+		int gpio = gpio_start + i;
+
+		if (gpio == gpio_reset)
+			continue;
+
+		ret = gpio_request(gpio, "camif");
+		if (!ret)
+			ret = s3c_gpio_cfgpin(gpio, S3C_GPIO_SFN(2));
+		if (ret) {
+			pr_err("failed to configure GPIO %d\n", gpio);
+			for (--i; i >= 0; i--)
+				gpio_free(gpio--);
+			return ret;
+		}
+		s3c_gpio_setpull(gpio, S3C_GPIO_PULL_NONE);
+	}
+
+	return 0;
+}
+
+void s3c_camif_gpio_put(void)
+{
+	int i, gpio_start, gpio_reset;
+
+	camif_get_gpios(&gpio_start, &gpio_reset);
+
+	for (i = 0; i < S3C_CAMIF_NUM_GPIOS; i++) {
+		int gpio = gpio_start + i;
+		if (gpio != gpio_reset)
+			gpio_free(gpio);
+	}
+}
diff --git a/arch/arm/plat-samsung/wakeup-mask.c b/arch/arm/plat-samsung/wakeup-mask.c
new file mode 100644
index 000000000..20c3d9117
--- /dev/null
+++ b/arch/arm/plat-samsung/wakeup-mask.c
@@ -0,0 +1,47 @@
+/* arch/arm/plat-samsung/wakeup-mask.c
+ *
+ * Copyright 2010 Ben Dooks <ben-linux@fluff.org>
+ *
+ * Support for wakeup mask interrupts on newer SoCs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/device.h>
+#include <linux/types.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+
+#include <plat/wakeup-mask.h>
+#include <plat/pm.h>
+
+void samsung_sync_wakemask(void __iomem *reg,
+			   struct samsung_wakeup_mask *mask, int nr_mask)
+{
+	struct irq_data *data;
+	u32 val;
+
+	val = __raw_readl(reg);
+
+	for (; nr_mask > 0; nr_mask--, mask++) {
+		if (mask->irq == NO_WAKEUP_IRQ) {
+			val |= mask->bit;
+			continue;
+		}
+
+		data = irq_get_irq_data(mask->irq);
+
+		/* bit of a liberty to read this directly from irq_data. */
+		if (irqd_is_wakeup_set(data))
+			val &= ~mask->bit;
+		else
+			val |= mask->bit;
+	}
+
+	printk(KERN_INFO "wakemask %08x => %08x\n", __raw_readl(reg), val);
+	__raw_writel(val, reg);
+}
diff --git a/arch/arm/plat-samsung/watchdog-reset.c b/arch/arm/plat-samsung/watchdog-reset.c
new file mode 100644
index 000000000..2ecb50bea
--- /dev/null
+++ b/arch/arm/plat-samsung/watchdog-reset.c
@@ -0,0 +1,97 @@
+/* arch/arm/plat-samsung/watchdog-reset.c
+ *
+ * Copyright (c) 2008 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Coyright (c) 2013 Tomasz Figa <tomasz.figa@gmail.com>
+ *
+ * Watchdog reset support for Samsung SoCs.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+
+#define S3C2410_WTCON			0x00
+#define S3C2410_WTDAT			0x04
+#define S3C2410_WTCNT			0x08
+
+#define S3C2410_WTCON_ENABLE		(1 << 5)
+#define S3C2410_WTCON_DIV16		(0 << 3)
+#define S3C2410_WTCON_RSTEN		(1 << 0)
+#define S3C2410_WTCON_PRESCALE(x)	((x) << 8)
+
+static void __iomem *wdt_base;
+static struct clk *wdt_clock;
+
+void samsung_wdt_reset(void)
+{
+	if (!wdt_base) {
+		pr_err("%s: wdt reset not initialized\n", __func__);
+		/* delay to allow the serial port to show the message */
+		mdelay(50);
+		return;
+	}
+
+	if (!IS_ERR(wdt_clock))
+		clk_prepare_enable(wdt_clock);
+
+	/* disable watchdog, to be safe  */
+	__raw_writel(0, wdt_base + S3C2410_WTCON);
+
+	/* put initial values into count and data */
+	__raw_writel(0x80, wdt_base + S3C2410_WTCNT);
+	__raw_writel(0x80, wdt_base + S3C2410_WTDAT);
+
+	/* set the watchdog to go and reset... */
+	__raw_writel(S3C2410_WTCON_ENABLE | S3C2410_WTCON_DIV16 |
+			S3C2410_WTCON_RSTEN | S3C2410_WTCON_PRESCALE(0x20),
+			wdt_base + S3C2410_WTCON);
+
+	/* wait for reset to assert... */
+	mdelay(500);
+
+	pr_err("Watchdog reset failed to assert reset\n");
+
+	/* delay to allow the serial port to show the message */
+	mdelay(50);
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id s3c2410_wdt_match[] = {
+	{ .compatible = "samsung,s3c2410-wdt" },
+	{},
+};
+
+void __init samsung_wdt_reset_of_init(void)
+{
+	struct device_node *np;
+
+	np = of_find_matching_node(NULL, s3c2410_wdt_match);
+	if (!np) {
+		pr_err("%s: failed to find watchdog node\n", __func__);
+		return;
+	}
+
+	wdt_base = of_iomap(np, 0);
+	if (!wdt_base) {
+		pr_err("%s: failed to map watchdog registers\n", __func__);
+		return;
+	}
+
+	wdt_clock = of_clk_get(np, 0);
+}
+#endif
+
+void __init samsung_wdt_reset_init(void __iomem *base)
+{
+	wdt_base = base;
+	wdt_clock = clk_get(NULL, "watchdog");
+}