Initial import

8 files changed, 1012 insertions, 0 deletions

diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig
new file mode 100644
index 000000000..8dc48214f
--- /dev/null
+++ b/arch/avr32/boards/atstk1000/Kconfig
@@ -0,0 +1,109 @@
+# STK1000 customization
+
+if BOARD_ATSTK1000
+
+choice
+	prompt "ATSTK1000 CPU daughterboard type"
+	default BOARD_ATSTK1002
+
+config BOARD_ATSTK1002
+	bool "ATSTK1002"
+	select CPU_AT32AP7000
+
+config BOARD_ATSTK1003
+	bool "ATSTK1003"
+	select CPU_AT32AP7001
+
+config BOARD_ATSTK1004
+	bool "ATSTK1004"
+	select CPU_AT32AP7002
+
+config BOARD_ATSTK1006
+	bool "ATSTK1006"
+	select CPU_AT32AP7000
+
+endchoice
+
+
+config BOARD_ATSTK100X_CUSTOM
+	bool "Non-default STK1002/STK1003/STK1004 jumper settings"
+	help
+	  You will normally leave the jumpers on the CPU card at their
+	  default settings.  If you need to use certain peripherals,
+	  you will need to change some of those jumpers.
+
+if BOARD_ATSTK100X_CUSTOM
+
+config BOARD_ATSTK100X_SW1_CUSTOM
+	bool "SW1: use SSC1 (not SPI0)"
+	help
+	  This also prevents using the external DAC as an audio interface,
+	  and means you can't initialize the on-board QVGA display.
+
+config BOARD_ATSTK100X_SW2_CUSTOM
+	bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)"
+	help
+	  If you change this you'll want an updated boot loader putting
+	  the console on UART-C not UART-A.
+
+config BOARD_ATSTK100X_SW3_CUSTOM
+	bool "SW3: use TIMER1 (not SSC0 and GCLK)"
+	help
+	  This also prevents using the external DAC as an audio interface.
+
+config BOARD_ATSTK100X_SW4_CUSTOM
+	bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)"
+	help
+	  To use the camera interface you'll need a custom card (on the
+	  PCI-format connector) connect a video sensor.
+
+config BOARD_ATSTK1002_SW5_CUSTOM
+	bool "SW5: use MACB1 (not LCDC)"
+	depends on BOARD_ATSTK1002
+
+config BOARD_ATSTK1002_SW6_CUSTOM
+	bool "SW6: more GPIOs (not MACB0)"
+	depends on BOARD_ATSTK1002
+
+endif	# custom
+
+config BOARD_ATSTK100X_SPI1
+	bool "Configure SPI1 controller"
+	depends on !BOARD_ATSTK100X_SW4_CUSTOM
+	help
+	  All the signals for the second SPI controller are available on
+	  GPIO lines and accessed through the J1 jumper block.  Say "y"
+	  here to configure that SPI controller.
+
+config BOARD_ATSTK1000_J2_LED
+	bool
+	default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB
+
+choice
+	prompt "LEDs connected to J2:"
+	depends on LEDS_GPIO && !BOARD_ATSTK100X_SW4_CUSTOM
+	optional
+	help
+	  Select this if you have jumpered the J2 jumper block to the
+	  LED0..LED7 amber leds, or to the RGB leds, using a ten-pin
+	  IDC cable.  A default "heartbeat" trigger is provided, but
+	  you can of course override this.
+
+config BOARD_ATSTK1000_J2_LED8
+	bool "LED0..LED7"
+	help
+	  Select this if J2 is jumpered to LED0..LED7 amber leds.
+
+config BOARD_ATSTK1000_J2_RGB
+	bool "RGB leds"
+	help
+	  Select this if J2 is jumpered to the RGB leds.
+
+endchoice
+
+config BOARD_ATSTK1000_EXTDAC
+	bool
+	depends on !BOARD_ATSTK100X_SW1_CUSTOM && !BOARD_ATSTK100X_SW3_CUSTOM
+	default y
+
+endif	# stk 1000
diff --git a/arch/avr32/boards/atstk1000/Makefile b/arch/avr32/boards/atstk1000/Makefile
new file mode 100644
index 000000000..edecee037
--- /dev/null
+++ b/arch/avr32/boards/atstk1000/Makefile
@@ -0,0 +1,5 @@
+obj-y				+= setup.o flash.o
+obj-$(CONFIG_BOARD_ATSTK1002)	+= atstk1002.o
+obj-$(CONFIG_BOARD_ATSTK1003)	+= atstk1003.o
+obj-$(CONFIG_BOARD_ATSTK1004)	+= atstk1004.o
+obj-$(CONFIG_BOARD_ATSTK1006)	+= atstk1002.o
diff --git a/arch/avr32/boards/atstk1000/atstk1000.h b/arch/avr32/boards/atstk1000/atstk1000.h
new file mode 100644
index 000000000..653cc09e5
--- /dev/null
+++ b/arch/avr32/boards/atstk1000/atstk1000.h
@@ -0,0 +1,17 @@
+/*
+ * ATSTK1000 setup code: Daughterboard interface
+ *
+ * Copyright (C) 2007 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
+#define __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H
+
+extern struct atmel_lcdfb_pdata atstk1000_lcdc_data;
+
+void atstk1000_setup_j2_leds(void);
+
+#endif /* __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H */
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
new file mode 100644
index 000000000..6c80aba7b
--- /dev/null
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -0,0 +1,330 @@
+/*
+ * ATSTK1002/ATSTK1006 daughterboard-specific init code
+ *
+ * Copyright (C) 2005-2007 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/etherdevice.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/string.h>
+#include <linux/types.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/at73c213.h>
+#include <linux/atmel-mci.h>
+
+#include <video/atmel_lcdc.h>
+
+#include <asm/io.h>
+#include <asm/setup.h>
+
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/init.h>
+#include <mach/portmux.h>
+
+#include "atstk1000.h"
+
+/* Oscillator frequencies. These are board specific */
+unsigned long at32_board_osc_rates[3] = {
+	[0] = 32768,	/* 32.768 kHz on RTC osc */
+	[1] = 20000000,	/* 20 MHz on osc0 */
+	[2] = 12000000,	/* 12 MHz on osc1 */
+};
+
+/*
+ * The ATSTK1006 daughterboard is very similar to the ATSTK1002. Both
+ * have the AT32AP7000 chip on board; the difference is that the
+ * STK1006 has 128 MB SDRAM (the STK1002 uses the 8 MB SDRAM chip on
+ * the STK1000 motherboard) and 256 MB NAND flash (the STK1002 has
+ * none.)
+ *
+ * The RAM difference is handled by the boot loader, so the only
+ * difference we end up handling here is the NAND flash.
+ */
+#ifdef CONFIG_BOARD_ATSTK1006
+#include <linux/mtd/partitions.h>
+#include <mach/smc.h>
+
+static struct smc_timing nand_timing __initdata = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 10,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 10,
+
+	.ncs_read_pulse		= 30,
+	.nrd_pulse		= 15,
+	.ncs_write_pulse	= 30,
+	.nwe_pulse		= 15,
+
+	.read_cycle		= 30,
+	.write_cycle		= 30,
+
+	.ncs_read_recover	= 0,
+	.nrd_recover		= 15,
+	.ncs_write_recover	= 0,
+	/* WE# high -> RE# low min 60 ns */
+	.nwe_recover		= 50,
+};
+
+static struct smc_config nand_config __initdata = {
+	.bus_width		= 1,
+	.nrd_controlled		= 1,
+	.nwe_controlled		= 1,
+	.nwait_mode		= 0,
+	.byte_write		= 0,
+	.tdf_cycles		= 2,
+	.tdf_mode		= 0,
+};
+
+static struct mtd_partition nand_partitions[] = {
+	{
+		.name		= "main",
+		.offset		= 0x00000000,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct atmel_nand_data atstk1006_nand_data __initdata = {
+	.cle		= 21,
+	.ale		= 22,
+	.rdy_pin	= GPIO_PIN_PB(30),
+	.enable_pin	= GPIO_PIN_PB(29),
+	.ecc_mode	= NAND_ECC_SOFT,
+	.parts		= nand_partitions,
+	.num_parts	= ARRAY_SIZE(nand_partitions),
+};
+#endif
+
+struct eth_addr {
+	u8 addr[6];
+};
+
+static struct eth_addr __initdata hw_addr[2];
+static struct macb_platform_data __initdata eth_data[2] = {
+	{
+		/*
+		 * The MDIO pullups on STK1000 are a bit too weak for
+		 * the autodetection to work properly, so we have to
+		 * mask out everything but the correct address.
+		 */
+		.phy_mask	= ~(1U << 16),
+	},
+	{
+		.phy_mask	= ~(1U << 17),
+	},
+};
+
+#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
+static struct at73c213_board_info at73c213_data = {
+	.ssc_id		= 0,
+	.shortname	= "AVR32 STK1000 external DAC",
+};
+#endif
+
+#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM
+static struct spi_board_info spi0_board_info[] __initdata = {
+#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
+	{
+		/* AT73C213 */
+		.modalias	= "at73c213",
+		.max_speed_hz	= 200000,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_1,
+		.platform_data	= &at73c213_data,
+	},
+#endif
+	{
+		/* QVGA display */
+		.modalias	= "ltv350qv",
+		.max_speed_hz	= 16000000,
+		.chip_select	= 1,
+		.mode		= SPI_MODE_3,
+	},
+};
+#endif
+
+#ifdef CONFIG_BOARD_ATSTK100X_SPI1
+static struct spi_board_info spi1_board_info[] __initdata = { {
+	/* patch in custom entries here */
+} };
+#endif
+
+/*
+ * The next two functions should go away as the boot loader is
+ * supposed to initialize the macb address registers with a valid
+ * ethernet address. But we need to keep it around for a while until
+ * we can be reasonably sure the boot loader does this.
+ *
+ * The phy_id is ignored as the driver will probe for it.
+ */
+static int __init parse_tag_ethernet(struct tag *tag)
+{
+	int i;
+
+	i = tag->u.ethernet.mac_index;
+	if (i < ARRAY_SIZE(hw_addr))
+		memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address,
+		       sizeof(hw_addr[i].addr));
+
+	return 0;
+}
+__tagtable(ATAG_ETHERNET, parse_tag_ethernet);
+
+static void __init set_hw_addr(struct platform_device *pdev)
+{
+	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	const u8 *addr;
+	void __iomem *regs;
+	struct clk *pclk;
+
+	if (!res)
+		return;
+	if (pdev->id >= ARRAY_SIZE(hw_addr))
+		return;
+
+	addr = hw_addr[pdev->id].addr;
+	if (!is_valid_ether_addr(addr))
+		return;
+
+	/*
+	 * Since this is board-specific code, we'll cheat and use the
+	 * physical address directly as we happen to know that it's
+	 * the same as the virtual address.
+	 */
+	regs = (void __iomem __force *)res->start;
+	pclk = clk_get(&pdev->dev, "pclk");
+	if (IS_ERR(pclk))
+		return;
+
+	clk_enable(pclk);
+	__raw_writel((addr[3] << 24) | (addr[2] << 16)
+		     | (addr[1] << 8) | addr[0], regs + 0x98);
+	__raw_writel((addr[5] << 8) | addr[4], regs + 0x9c);
+	clk_disable(pclk);
+	clk_put(pclk);
+}
+
+#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
+static void __init atstk1002_setup_extdac(void)
+{
+	struct clk *gclk;
+	struct clk *pll;
+
+	gclk = clk_get(NULL, "gclk0");
+	if (IS_ERR(gclk))
+		goto err_gclk;
+	pll = clk_get(NULL, "pll0");
+	if (IS_ERR(pll))
+		goto err_pll;
+
+	if (clk_set_parent(gclk, pll)) {
+		pr_debug("STK1000: failed to set pll0 as parent for DAC clock\n");
+		goto err_set_clk;
+	}
+
+	at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0);
+	at73c213_data.dac_clk = gclk;
+
+err_set_clk:
+	clk_put(pll);
+err_pll:
+	clk_put(gclk);
+err_gclk:
+	return;
+}
+#else
+static void __init atstk1002_setup_extdac(void)
+{
+
+}
+#endif /* CONFIG_BOARD_ATSTK1000_EXTDAC */
+
+void __init setup_board(void)
+{
+#ifdef	CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+	at32_map_usart(0, 1, 0);	/* USART 0/B: /dev/ttyS1, IRDA */
+#else
+	at32_map_usart(1, 0, 0);	/* USART 1/A: /dev/ttyS0, DB9 */
+#endif
+	/* USART 2/unused: expansion connector */
+	at32_map_usart(3, 2, 0);	/* USART 3/C: /dev/ttyS2, DB9 */
+
+	at32_setup_serial_console(0);
+}
+
+#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+
+/* MMC card detect requires MACB0 *NOT* be used */
+#ifdef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM
+		.detect_pin	= GPIO_PIN_PC(14), /* gpio30/sdcd */
+		.wp_pin		= GPIO_PIN_PC(15), /* gpio31/sdwp */
+#else
+		.detect_pin	= -ENODEV,
+		.wp_pin		= -ENODEV,
+#endif	/* SW6 for sd{cd,wp} routing */
+	},
+};
+
+#endif	/* SW2 for MMC signal routing */
+
+static int __init atstk1002_init(void)
+{
+	/*
+	 * ATSTK1000 uses 32-bit SDRAM interface. Reserve the
+	 * SDRAM-specific pins so that nobody messes with them.
+	 */
+	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
+
+#ifdef CONFIG_BOARD_ATSTK1006
+	smc_set_timing(&nand_config, &nand_timing);
+	smc_set_configuration(3, &nand_config);
+	at32_add_device_nand(0, &atstk1006_nand_data);
+#endif
+
+#ifdef	CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+	at32_add_device_usart(1);
+#else
+	at32_add_device_usart(0);
+#endif
+	at32_add_device_usart(2);
+
+#ifndef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM
+	set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
+#endif
+#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM
+	at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
+#endif
+#ifdef CONFIG_BOARD_ATSTK100X_SPI1
+	at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
+#endif
+#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+	at32_add_device_mci(0, &mci0_data);
+#endif
+#ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM
+	set_hw_addr(at32_add_device_eth(1, &eth_data[1]));
+#else
+	at32_add_device_lcdc(0, &atstk1000_lcdc_data,
+			     fbmem_start, fbmem_size,
+			     ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL);
+#endif
+	at32_add_device_usba(0, NULL);
+#ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM
+	at32_add_device_ssc(0, ATMEL_SSC_TX);
+#endif
+
+	atstk1000_setup_j2_leds();
+	atstk1002_setup_extdac();
+
+	return 0;
+}
+postcore_initcall(atstk1002_init);
diff --git a/arch/avr32/boards/atstk1000/atstk1003.c b/arch/avr32/boards/atstk1000/atstk1003.c
new file mode 100644
index 000000000..ff7e23298
--- /dev/null
+++ b/arch/avr32/boards/atstk1000/atstk1003.c
@@ -0,0 +1,162 @@
+/*
+ * ATSTK1003 daughterboard-specific init code
+ *
+ * Copyright (C) 2007 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/string.h>
+#include <linux/types.h>
+
+#include <linux/spi/at73c213.h>
+#include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
+
+#include <asm/setup.h>
+
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/init.h>
+#include <mach/portmux.h>
+
+#include "atstk1000.h"
+
+/* Oscillator frequencies. These are board specific */
+unsigned long at32_board_osc_rates[3] = {
+	[0] = 32768,	/* 32.768 kHz on RTC osc */
+	[1] = 20000000,	/* 20 MHz on osc0 */
+	[2] = 12000000,	/* 12 MHz on osc1 */
+};
+
+#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
+static struct at73c213_board_info at73c213_data = {
+	.ssc_id		= 0,
+	.shortname	= "AVR32 STK1000 external DAC",
+};
+#endif
+
+#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM
+static struct spi_board_info spi0_board_info[] __initdata = {
+#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
+	{
+		/* AT73C213 */
+		.modalias	= "at73c213",
+		.max_speed_hz	= 200000,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_1,
+		.platform_data	= &at73c213_data,
+	},
+#endif
+	/*
+	 * We can control the LTV350QV LCD panel, but it isn't much
+	 * point since we don't have an LCD controller...
+	 */
+};
+#endif
+
+#ifdef CONFIG_BOARD_ATSTK100X_SPI1
+static struct spi_board_info spi1_board_info[] __initdata = { {
+	/* patch in custom entries here */
+} };
+#endif
+
+#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -ENODEV,
+		.wp_pin		= -ENODEV,
+	},
+};
+#endif
+
+#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
+static void __init atstk1003_setup_extdac(void)
+{
+	struct clk *gclk;
+	struct clk *pll;
+
+	gclk = clk_get(NULL, "gclk0");
+	if (IS_ERR(gclk))
+		goto err_gclk;
+	pll = clk_get(NULL, "pll0");
+	if (IS_ERR(pll))
+		goto err_pll;
+
+	if (clk_set_parent(gclk, pll)) {
+		pr_debug("STK1000: failed to set pll0 as parent for DAC clock\n");
+		goto err_set_clk;
+	}
+
+	at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0);
+	at73c213_data.dac_clk = gclk;
+
+err_set_clk:
+	clk_put(pll);
+err_pll:
+	clk_put(gclk);
+err_gclk:
+	return;
+}
+#else
+static void __init atstk1003_setup_extdac(void)
+{
+
+}
+#endif /* CONFIG_BOARD_ATSTK1000_EXTDAC */
+
+void __init setup_board(void)
+{
+#ifdef	CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+	at32_map_usart(0, 1, 0);	/* USART 0/B: /dev/ttyS1, IRDA */
+#else
+	at32_map_usart(1, 0, 0);	/* USART 1/A: /dev/ttyS0, DB9 */
+#endif
+	/* USART 2/unused: expansion connector */
+	at32_map_usart(3, 2, 0);	/* USART 3/C: /dev/ttyS2, DB9 */
+
+	at32_setup_serial_console(0);
+}
+
+static int __init atstk1003_init(void)
+{
+	/*
+	 * ATSTK1000 uses 32-bit SDRAM interface. Reserve the
+	 * SDRAM-specific pins so that nobody messes with them.
+	 */
+	at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
+
+#ifdef	CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+	at32_add_device_usart(1);
+#else
+	at32_add_device_usart(0);
+#endif
+	at32_add_device_usart(2);
+
+#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM
+	at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
+#endif
+#ifdef CONFIG_BOARD_ATSTK100X_SPI1
+	at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
+#endif
+#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+	at32_add_device_mci(0, &mci0_data);
+#endif
+	at32_add_device_usba(0, NULL);
+#ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM
+	at32_add_device_ssc(0, ATMEL_SSC_TX);
+#endif
+
+	atstk1000_setup_j2_leds();
+	atstk1003_setup_extdac();
+
+	return 0;
+}
+postcore_initcall(atstk1003_init);
diff --git a/arch/avr32/boards/atstk1000/atstk1004.c b/arch/avr32/boards/atstk1000/atstk1004.c
new file mode 100644
index 000000000..69a9f0f08
--- /dev/null
+++ b/arch/avr32/boards/atstk1000/atstk1004.c
@@ -0,0 +1,164 @@
+/*
+ * ATSTK1003 daughterboard-specific init code
+ *
+ * Copyright (C) 2007 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/string.h>
+#include <linux/types.h>
+
+#include <linux/spi/at73c213.h>
+#include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
+
+#include <video/atmel_lcdc.h>
+
+#include <asm/setup.h>
+
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/init.h>
+#include <mach/portmux.h>
+
+#include "atstk1000.h"
+
+/* Oscillator frequencies. These are board specific */
+unsigned long at32_board_osc_rates[3] = {
+	[0] = 32768,	/* 32.768 kHz on RTC osc */
+	[1] = 20000000,	/* 20 MHz on osc0 */
+	[2] = 12000000,	/* 12 MHz on osc1 */
+};
+
+#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
+static struct at73c213_board_info at73c213_data = {
+	.ssc_id		= 0,
+	.shortname	= "AVR32 STK1000 external DAC",
+};
+#endif
+
+#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM
+static struct spi_board_info spi0_board_info[] __initdata = {
+#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
+	{
+		/* AT73C213 */
+		.modalias	= "at73c213",
+		.max_speed_hz	= 200000,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_1,
+		.platform_data	= &at73c213_data,
+	},
+#endif
+	{
+		/* QVGA display */
+		.modalias	= "ltv350qv",
+		.max_speed_hz	= 16000000,
+		.chip_select	= 1,
+		.mode		= SPI_MODE_3,
+	},
+};
+#endif
+
+#ifdef CONFIG_BOARD_ATSTK100X_SPI1
+static struct spi_board_info spi1_board_info[] __initdata = { {
+	/* patch in custom entries here */
+} };
+#endif
+
+#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -ENODEV,
+		.wp_pin		= -ENODEV,
+	},
+};
+#endif
+
+#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
+static void __init atstk1004_setup_extdac(void)
+{
+	struct clk *gclk;
+	struct clk *pll;
+
+	gclk = clk_get(NULL, "gclk0");
+	if (IS_ERR(gclk))
+		goto err_gclk;
+	pll = clk_get(NULL, "pll0");
+	if (IS_ERR(pll))
+		goto err_pll;
+
+	if (clk_set_parent(gclk, pll)) {
+		pr_debug("STK1000: failed to set pll0 as parent for DAC clock\n");
+		goto err_set_clk;
+	}
+
+	at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0);
+	at73c213_data.dac_clk = gclk;
+
+err_set_clk:
+	clk_put(pll);
+err_pll:
+	clk_put(gclk);
+err_gclk:
+	return;
+}
+#else
+static void __init atstk1004_setup_extdac(void)
+{
+
+}
+#endif /* CONFIG_BOARD_ATSTK1000_EXTDAC */
+
+void __init setup_board(void)
+{
+#ifdef	CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+	at32_map_usart(0, 1, 0);	/* USART 0/B: /dev/ttyS1, IRDA */
+#else
+	at32_map_usart(1, 0, 0);	/* USART 1/A: /dev/ttyS0, DB9 */
+#endif
+	/* USART 2/unused: expansion connector */
+	at32_map_usart(3, 2, 0);	/* USART 3/C: /dev/ttyS2, DB9 */
+
+	at32_setup_serial_console(0);
+}
+
+static int __init atstk1004_init(void)
+{
+#ifdef	CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+	at32_add_device_usart(1);
+#else
+	at32_add_device_usart(0);
+#endif
+	at32_add_device_usart(2);
+
+#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM
+	at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
+#endif
+#ifdef CONFIG_BOARD_ATSTK100X_SPI1
+	at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
+#endif
+#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
+	at32_add_device_mci(0, &mci0_data);
+#endif
+	at32_add_device_lcdc(0, &atstk1000_lcdc_data,
+			     fbmem_start, fbmem_size,
+			     ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL);
+	at32_add_device_usba(0, NULL);
+#ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM
+	at32_add_device_ssc(0, ATMEL_SSC_TX);
+#endif
+
+	atstk1000_setup_j2_leds();
+	atstk1004_setup_extdac();
+
+	return 0;
+}
+postcore_initcall(atstk1004_init);
diff --git a/arch/avr32/boards/atstk1000/flash.c b/arch/avr32/boards/atstk1000/flash.c
new file mode 100644
index 000000000..6e4d56197
--- /dev/null
+++ b/arch/avr32/boards/atstk1000/flash.c
@@ -0,0 +1,98 @@
+/*
+ * ATSTK1000 board-specific flash initialization
+ *
+ * Copyright (C) 2005-2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <mach/smc.h>
+
+static struct smc_timing flash_timing __initdata = {
+	.ncs_read_setup		= 0,
+	.nrd_setup		= 40,
+	.ncs_write_setup	= 0,
+	.nwe_setup		= 10,
+
+	.ncs_read_pulse		= 80,
+	.nrd_pulse		= 40,
+	.ncs_write_pulse	= 65,
+	.nwe_pulse		= 55,
+
+	.read_cycle		= 120,
+	.write_cycle		= 120,
+};
+
+static struct smc_config flash_config __initdata = {
+	.bus_width		= 2,
+	.nrd_controlled		= 1,
+	.nwe_controlled		= 1,
+	.byte_write		= 1,
+};
+
+static struct mtd_partition flash_parts[] = {
+	{
+		.name           = "u-boot",
+		.offset         = 0x00000000,
+		.size           = 0x00020000,           /* 128 KiB */
+		.mask_flags     = MTD_WRITEABLE,
+	},
+	{
+		.name           = "root",
+		.offset         = 0x00020000,
+		.size           = 0x007d0000,
+	},
+	{
+		.name           = "env",
+		.offset         = 0x007f0000,
+		.size           = 0x00010000,
+		.mask_flags     = MTD_WRITEABLE,
+	},
+};
+
+static struct physmap_flash_data flash_data = {
+	.width		= 2,
+	.nr_parts	= ARRAY_SIZE(flash_parts),
+	.parts		= flash_parts,
+};
+
+static struct resource flash_resource = {
+	.start		= 0x00000000,
+	.end		= 0x007fffff,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device flash_device = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.resource	= &flash_resource,
+	.num_resources	= 1,
+	.dev		= {
+		.platform_data = &flash_data,
+	},
+};
+
+/* This needs to be called after the SMC has been initialized */
+static int __init atstk1000_flash_init(void)
+{
+	int ret;
+
+	smc_set_timing(&flash_config, &flash_timing);
+	ret = smc_set_configuration(0, &flash_config);
+	if (ret < 0) {
+		printk(KERN_ERR "atstk1000: failed to set NOR flash timing\n");
+		return ret;
+	}
+
+	platform_device_register(&flash_device);
+
+	return 0;
+}
+device_initcall(atstk1000_flash_init);
diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c
new file mode 100644
index 000000000..b6b88f5e0
--- /dev/null
+++ b/arch/avr32/boards/atstk1000/setup.c
@@ -0,0 +1,127 @@
+/*
+ * ATSTK1000 board-specific setup code.
+ *
+ * Copyright (C) 2005-2006 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/bootmem.h>
+#include <linux/fb.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+#include <linux/linkage.h>
+
+#include <video/atmel_lcdc.h>
+
+#include <asm/setup.h>
+
+#include <mach/at32ap700x.h>
+#include <mach/board.h>
+#include <mach/portmux.h>
+
+#include "atstk1000.h"
+
+/* Initialized by bootloader-specific startup code. */
+struct tag *bootloader_tags __initdata;
+
+static struct fb_videomode __initdata ltv350qv_modes[] = {
+	{
+		.name		= "320x240 @ 75",
+		.refresh	= 75,
+		.xres		= 320,		.yres		= 240,
+		.pixclock	= KHZ2PICOS(6891),
+
+		.left_margin	= 17,		.right_margin	= 33,
+		.upper_margin	= 10,		.lower_margin	= 10,
+		.hsync_len	= 16,		.vsync_len	= 1,
+
+		.sync		= 0,
+		.vmode		= FB_VMODE_NONINTERLACED,
+	},
+};
+
+static struct fb_monspecs __initdata atstk1000_default_monspecs = {
+	.manufacturer		= "SNG",
+	.monitor		= "LTV350QV",
+	.modedb			= ltv350qv_modes,
+	.modedb_len		= ARRAY_SIZE(ltv350qv_modes),
+	.hfmin			= 14820,
+	.hfmax			= 22230,
+	.vfmin			= 60,
+	.vfmax			= 90,
+	.dclkmax		= 30000000,
+};
+
+struct atmel_lcdfb_pdata __initdata atstk1000_lcdc_data = {
+	.default_bpp		= 24,
+	.default_dmacon		= ATMEL_LCDC_DMAEN | ATMEL_LCDC_DMA2DEN,
+	.default_lcdcon2	= (ATMEL_LCDC_DISTYPE_TFT
+				   | ATMEL_LCDC_INVCLK
+				   | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE
+				   | ATMEL_LCDC_MEMOR_BIG),
+	.default_monspecs	= &atstk1000_default_monspecs,
+	.guard_time		= 2,
+};
+
+#ifdef CONFIG_BOARD_ATSTK1000_J2_LED
+#include <linux/leds.h>
+
+static struct gpio_led stk1000_j2_led[] = {
+#ifdef CONFIG_BOARD_ATSTK1000_J2_LED8
+#define LEDSTRING "J2 jumpered to LED8"
+	{ .name = "led0:amber", .gpio = GPIO_PIN_PB( 8), },
+	{ .name = "led1:amber", .gpio = GPIO_PIN_PB( 9), },
+	{ .name = "led2:amber", .gpio = GPIO_PIN_PB(10), },
+	{ .name = "led3:amber", .gpio = GPIO_PIN_PB(13), },
+	{ .name = "led4:amber", .gpio = GPIO_PIN_PB(14), },
+	{ .name = "led5:amber", .gpio = GPIO_PIN_PB(15), },
+	{ .name = "led6:amber", .gpio = GPIO_PIN_PB(16), },
+	{ .name = "led7:amber", .gpio = GPIO_PIN_PB(30),
+			.default_trigger = "heartbeat", },
+#else	/* RGB */
+#define LEDSTRING "J2 jumpered to RGB LEDs"
+	{ .name = "r1:red",     .gpio = GPIO_PIN_PB( 8), },
+	{ .name = "g1:green",   .gpio = GPIO_PIN_PB(10), },
+	{ .name = "b1:blue",    .gpio = GPIO_PIN_PB(14), },
+
+	{ .name = "r2:red",     .gpio = GPIO_PIN_PB( 9),
+			.default_trigger = "heartbeat", },
+	{ .name = "g2:green",   .gpio = GPIO_PIN_PB(13), },
+	{ .name = "b2:blue",    .gpio = GPIO_PIN_PB(15),
+			.default_trigger = "heartbeat", },
+	/* PB16, PB30 unused */
+#endif
+};
+
+static struct gpio_led_platform_data stk1000_j2_led_data = {
+	.num_leds	= ARRAY_SIZE(stk1000_j2_led),
+	.leds		= stk1000_j2_led,
+};
+
+static struct platform_device stk1000_j2_led_dev = {
+	.name		= "leds-gpio",
+	.id		= 2,	/* gpio block J2 */
+	.dev		= {
+		.platform_data	= &stk1000_j2_led_data,
+	},
+};
+
+void __init atstk1000_setup_j2_leds(void)
+{
+	unsigned	i;
+
+	for (i = 0; i < ARRAY_SIZE(stk1000_j2_led); i++)
+		at32_select_gpio(stk1000_j2_led[i].gpio, AT32_GPIOF_OUTPUT);
+
+	printk("STK1000: " LEDSTRING "\n");
+	platform_device_register(&stk1000_j2_led_dev);
+}
+#else /* CONFIG_BOARD_ATSTK1000_J2_LED */
+void __init atstk1000_setup_j2_leds(void)
+{
+
+}
+#endif /* CONFIG_BOARD_ATSTK1000_J2_LED */