Initial import

1 files changed, 1066 insertions, 0 deletions

diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
new file mode 100644
index 000000000..3ba843f5c
--- /dev/null
+++ b/drivers/ata/pata_hpt37x.c
@@ -0,0 +1,1066 @@
+/*
+ * Libata driver for the highpoint 37x and 30x UDMA66 ATA controllers.
+ *
+ * This driver is heavily based upon:
+ *
+ * linux/drivers/ide/pci/hpt366.c		Version 0.36	April 25, 2003
+ *
+ * Copyright (C) 1999-2003		Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 2001	        Sun Microsystems, Inc.
+ * Portions Copyright (C) 2003		Red Hat Inc
+ * Portions Copyright (C) 2005-2010	MontaVista Software, Inc.
+ *
+ * TODO
+ *	Look into engine reset on timeout errors. Should not be	required.
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME	"pata_hpt37x"
+#define DRV_VERSION	"0.6.23"
+
+struct hpt_clock {
+	u8	xfer_speed;
+	u32	timing;
+};
+
+struct hpt_chip {
+	const char *name;
+	unsigned int base;
+	struct hpt_clock const *clocks[4];
+};
+
+/* key for bus clock timings
+ * bit
+ * 0:3    data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
+ *        cycles = value + 1
+ * 4:8    data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
+ *        cycles = value + 1
+ * 9:12   cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 13:17  cmd_low_time. Active time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 18:20  udma_cycle_time. Clock cycles for UDMA xfer.
+ * 21     CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
+ * 22:24  pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
+ * 25:27  cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
+ *        register access.
+ * 28     UDMA enable.
+ * 29     DMA  enable.
+ * 30     PIO_MST enable. If set, the chip is in bus master mode during
+ *        PIO xfer.
+ * 31     FIFO enable. Only for PIO.
+ */
+
+static struct hpt_clock hpt37x_timings_33[] = {
+	{ XFER_UDMA_6,		0x12446231 },	/* 0x12646231 ?? */
+	{ XFER_UDMA_5,		0x12446231 },
+	{ XFER_UDMA_4,		0x12446231 },
+	{ XFER_UDMA_3,		0x126c6231 },
+	{ XFER_UDMA_2,		0x12486231 },
+	{ XFER_UDMA_1,		0x124c6233 },
+	{ XFER_UDMA_0,		0x12506297 },
+
+	{ XFER_MW_DMA_2,	0x22406c31 },
+	{ XFER_MW_DMA_1,	0x22406c33 },
+	{ XFER_MW_DMA_0,	0x22406c97 },
+
+	{ XFER_PIO_4,		0x06414e31 },
+	{ XFER_PIO_3,		0x06414e42 },
+	{ XFER_PIO_2,		0x06414e53 },
+	{ XFER_PIO_1,		0x06814e93 },
+	{ XFER_PIO_0,		0x06814ea7 }
+};
+
+static struct hpt_clock hpt37x_timings_50[] = {
+	{ XFER_UDMA_6,		0x12848242 },
+	{ XFER_UDMA_5,		0x12848242 },
+	{ XFER_UDMA_4,		0x12ac8242 },
+	{ XFER_UDMA_3,		0x128c8242 },
+	{ XFER_UDMA_2,		0x120c8242 },
+	{ XFER_UDMA_1,		0x12148254 },
+	{ XFER_UDMA_0,		0x121882ea },
+
+	{ XFER_MW_DMA_2,	0x22808242 },
+	{ XFER_MW_DMA_1,	0x22808254 },
+	{ XFER_MW_DMA_0,	0x228082ea },
+
+	{ XFER_PIO_4,		0x0a81f442 },
+	{ XFER_PIO_3,		0x0a81f443 },
+	{ XFER_PIO_2,		0x0a81f454 },
+	{ XFER_PIO_1,		0x0ac1f465 },
+	{ XFER_PIO_0,		0x0ac1f48a }
+};
+
+static struct hpt_clock hpt37x_timings_66[] = {
+	{ XFER_UDMA_6,		0x1c869c62 },
+	{ XFER_UDMA_5,		0x1cae9c62 },	/* 0x1c8a9c62 */
+	{ XFER_UDMA_4,		0x1c8a9c62 },
+	{ XFER_UDMA_3,		0x1c8e9c62 },
+	{ XFER_UDMA_2,		0x1c929c62 },
+	{ XFER_UDMA_1,		0x1c9a9c62 },
+	{ XFER_UDMA_0,		0x1c829c62 },
+
+	{ XFER_MW_DMA_2,	0x2c829c62 },
+	{ XFER_MW_DMA_1,	0x2c829c66 },
+	{ XFER_MW_DMA_0,	0x2c829d2e },
+
+	{ XFER_PIO_4,		0x0c829c62 },
+	{ XFER_PIO_3,		0x0c829c84 },
+	{ XFER_PIO_2,		0x0c829ca6 },
+	{ XFER_PIO_1,		0x0d029d26 },
+	{ XFER_PIO_0,		0x0d029d5e }
+};
+
+
+static const struct hpt_chip hpt370 = {
+	"HPT370",
+	48,
+	{
+		hpt37x_timings_33,
+		NULL,
+		NULL,
+		NULL
+	}
+};
+
+static const struct hpt_chip hpt370a = {
+	"HPT370A",
+	48,
+	{
+		hpt37x_timings_33,
+		NULL,
+		hpt37x_timings_50,
+		NULL
+	}
+};
+
+static const struct hpt_chip hpt372 = {
+	"HPT372",
+	55,
+	{
+		hpt37x_timings_33,
+		NULL,
+		hpt37x_timings_50,
+		hpt37x_timings_66
+	}
+};
+
+static const struct hpt_chip hpt302 = {
+	"HPT302",
+	66,
+	{
+		hpt37x_timings_33,
+		NULL,
+		hpt37x_timings_50,
+		hpt37x_timings_66
+	}
+};
+
+static const struct hpt_chip hpt371 = {
+	"HPT371",
+	66,
+	{
+		hpt37x_timings_33,
+		NULL,
+		hpt37x_timings_50,
+		hpt37x_timings_66
+	}
+};
+
+static const struct hpt_chip hpt372a = {
+	"HPT372A",
+	66,
+	{
+		hpt37x_timings_33,
+		NULL,
+		hpt37x_timings_50,
+		hpt37x_timings_66
+	}
+};
+
+static const struct hpt_chip hpt374 = {
+	"HPT374",
+	48,
+	{
+		hpt37x_timings_33,
+		NULL,
+		NULL,
+		NULL
+	}
+};
+
+/**
+ *	hpt37x_find_mode	-	reset the hpt37x bus
+ *	@ap: ATA port
+ *	@speed: transfer mode
+ *
+ *	Return the 32bit register programming information for this channel
+ *	that matches the speed provided.
+ */
+
+static u32 hpt37x_find_mode(struct ata_port *ap, int speed)
+{
+	struct hpt_clock *clocks = ap->host->private_data;
+
+	while (clocks->xfer_speed) {
+		if (clocks->xfer_speed == speed)
+			return clocks->timing;
+		clocks++;
+	}
+	BUG();
+	return 0xffffffffU;	/* silence compiler warning */
+}
+
+static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr,
+			       const char * const list[])
+{
+	unsigned char model_num[ATA_ID_PROD_LEN + 1];
+	int i = 0;
+
+	ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
+
+	while (list[i] != NULL) {
+		if (!strcmp(list[i], model_num)) {
+			pr_warn("%s is not supported for %s\n",
+				modestr, list[i]);
+			return 1;
+		}
+		i++;
+	}
+	return 0;
+}
+
+static const char * const bad_ata33[] = {
+	"Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3",
+	"Maxtor 90845U3", "Maxtor 90650U2",
+	"Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5",
+	"Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
+	"Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6",
+	"Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
+	"Maxtor 90510D4",
+	"Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
+	"Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7",
+	"Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
+	"Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5",
+	"Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
+	NULL
+};
+
+static const char * const bad_ata100_5[] = {
+	"IBM-DTLA-307075",
+	"IBM-DTLA-307060",
+	"IBM-DTLA-307045",
+	"IBM-DTLA-307030",
+	"IBM-DTLA-307020",
+	"IBM-DTLA-307015",
+	"IBM-DTLA-305040",
+	"IBM-DTLA-305030",
+	"IBM-DTLA-305020",
+	"IC35L010AVER07-0",
+	"IC35L020AVER07-0",
+	"IC35L030AVER07-0",
+	"IC35L040AVER07-0",
+	"IC35L060AVER07-0",
+	"WDC AC310200R",
+	NULL
+};
+
+/**
+ *	hpt370_filter	-	mode selection filter
+ *	@adev: ATA device
+ *
+ *	Block UDMA on devices that cause trouble with this controller.
+ */
+
+static unsigned long hpt370_filter(struct ata_device *adev, unsigned long mask)
+{
+	if (adev->class == ATA_DEV_ATA) {
+		if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33))
+			mask &= ~ATA_MASK_UDMA;
+		if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5))
+			mask &= ~(0xE0 << ATA_SHIFT_UDMA);
+	}
+	return mask;
+}
+
+/**
+ *	hpt370a_filter	-	mode selection filter
+ *	@adev: ATA device
+ *
+ *	Block UDMA on devices that cause trouble with this controller.
+ */
+
+static unsigned long hpt370a_filter(struct ata_device *adev, unsigned long mask)
+{
+	if (adev->class == ATA_DEV_ATA) {
+		if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5))
+			mask &= ~(0xE0 << ATA_SHIFT_UDMA);
+	}
+	return mask;
+}
+
+/**
+ *	hpt372_filter	-	mode selection filter
+ *	@adev: ATA device
+ *	@mask: mode mask
+ *
+ *	The Marvell bridge chips used on the HighPoint SATA cards do not seem
+ *	to support the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes...
+ */
+static unsigned long hpt372_filter(struct ata_device *adev, unsigned long mask)
+{
+	if (ata_id_is_sata(adev->id))
+		mask &= ~((0xE << ATA_SHIFT_UDMA) | ATA_MASK_MWDMA);
+
+	return mask;
+}
+
+/**
+ *	hpt37x_cable_detect	-	Detect the cable type
+ *	@ap: ATA port to detect on
+ *
+ *	Return the cable type attached to this port
+ */
+
+static int hpt37x_cable_detect(struct ata_port *ap)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u8 scr2, ata66;
+
+	pci_read_config_byte(pdev, 0x5B, &scr2);
+	pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
+
+	udelay(10); /* debounce */
+
+	/* Cable register now active */
+	pci_read_config_byte(pdev, 0x5A, &ata66);
+	/* Restore state */
+	pci_write_config_byte(pdev, 0x5B, scr2);
+
+	if (ata66 & (2 >> ap->port_no))
+		return ATA_CBL_PATA40;
+	else
+		return ATA_CBL_PATA80;
+}
+
+/**
+ *	hpt374_fn1_cable_detect	-	Detect the cable type
+ *	@ap: ATA port to detect on
+ *
+ *	Return the cable type attached to this port
+ */
+
+static int hpt374_fn1_cable_detect(struct ata_port *ap)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	unsigned int mcrbase = 0x50 + 4 * ap->port_no;
+	u16 mcr3;
+	u8 ata66;
+
+	/* Do the extra channel work */
+	pci_read_config_word(pdev, mcrbase + 2, &mcr3);
+	/* Set bit 15 of 0x52 to enable TCBLID as input */
+	pci_write_config_word(pdev, mcrbase + 2, mcr3 | 0x8000);
+	pci_read_config_byte(pdev, 0x5A, &ata66);
+	/* Reset TCBLID/FCBLID to output */
+	pci_write_config_word(pdev, mcrbase + 2, mcr3);
+
+	if (ata66 & (2 >> ap->port_no))
+		return ATA_CBL_PATA40;
+	else
+		return ATA_CBL_PATA80;
+}
+
+/**
+ *	hpt37x_pre_reset	-	reset the hpt37x bus
+ *	@link: ATA link to reset
+ *	@deadline: deadline jiffies for the operation
+ *
+ *	Perform the initial reset handling for the HPT37x.
+ */
+
+static int hpt37x_pre_reset(struct ata_link *link, unsigned long deadline)
+{
+	struct ata_port *ap = link->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	static const struct pci_bits hpt37x_enable_bits[] = {
+		{ 0x50, 1, 0x04, 0x04 },
+		{ 0x54, 1, 0x04, 0x04 }
+	};
+
+	if (!pci_test_config_bits(pdev, &hpt37x_enable_bits[ap->port_no]))
+		return -ENOENT;
+
+	/* Reset the state machine */
+	pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+	udelay(100);
+
+	return ata_sff_prereset(link, deadline);
+}
+
+static void hpt370_set_mode(struct ata_port *ap, struct ata_device *adev,
+			    u8 mode)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 addr1, addr2;
+	u32 reg, timing, mask;
+	u8 fast;
+
+	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+	addr2 = 0x51 + 4 * ap->port_no;
+
+	/* Fast interrupt prediction disable, hold off interrupt disable */
+	pci_read_config_byte(pdev, addr2, &fast);
+	fast &= ~0x02;
+	fast |= 0x01;
+	pci_write_config_byte(pdev, addr2, fast);
+
+	/* Determine timing mask and find matching mode entry */
+	if (mode < XFER_MW_DMA_0)
+		mask = 0xcfc3ffff;
+	else if (mode < XFER_UDMA_0)
+		mask = 0x31c001ff;
+	else
+		mask = 0x303c0000;
+
+	timing = hpt37x_find_mode(ap, mode);
+
+	pci_read_config_dword(pdev, addr1, &reg);
+	reg = (reg & ~mask) | (timing & mask);
+	pci_write_config_dword(pdev, addr1, reg);
+}
+/**
+ *	hpt370_set_piomode		-	PIO setup
+ *	@ap: ATA interface
+ *	@adev: device on the interface
+ *
+ *	Perform PIO mode setup.
+ */
+
+static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	hpt370_set_mode(ap, adev, adev->pio_mode);
+}
+
+/**
+ *	hpt370_set_dmamode		-	DMA timing setup
+ *	@ap: ATA interface
+ *	@adev: Device being configured
+ *
+ *	Set up the channel for MWDMA or UDMA modes.
+ */
+
+static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+	hpt370_set_mode(ap, adev, adev->dma_mode);
+}
+
+/**
+ *	hpt370_bmdma_end		-	DMA engine stop
+ *	@qc: ATA command
+ *
+ *	Work around the HPT370 DMA engine.
+ */
+
+static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	void __iomem *bmdma = ap->ioaddr.bmdma_addr;
+	u8 dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
+	u8 dma_cmd;
+
+	if (dma_stat & ATA_DMA_ACTIVE) {
+		udelay(20);
+		dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
+	}
+	if (dma_stat & ATA_DMA_ACTIVE) {
+		/* Clear the engine */
+		pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+		udelay(10);
+		/* Stop DMA */
+		dma_cmd = ioread8(bmdma + ATA_DMA_CMD);
+		iowrite8(dma_cmd & ~ATA_DMA_START, bmdma + ATA_DMA_CMD);
+		/* Clear Error */
+		dma_stat = ioread8(bmdma + ATA_DMA_STATUS);
+		iowrite8(dma_stat | ATA_DMA_INTR | ATA_DMA_ERR,
+			 bmdma + ATA_DMA_STATUS);
+		/* Clear the engine */
+		pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+		udelay(10);
+	}
+	ata_bmdma_stop(qc);
+}
+
+static void hpt372_set_mode(struct ata_port *ap, struct ata_device *adev,
+			    u8 mode)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 addr1, addr2;
+	u32 reg, timing, mask;
+	u8 fast;
+
+	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+	addr2 = 0x51 + 4 * ap->port_no;
+
+	/* Fast interrupt prediction disable, hold off interrupt disable */
+	pci_read_config_byte(pdev, addr2, &fast);
+	fast &= ~0x07;
+	pci_write_config_byte(pdev, addr2, fast);
+
+	/* Determine timing mask and find matching mode entry */
+	if (mode < XFER_MW_DMA_0)
+		mask = 0xcfc3ffff;
+	else if (mode < XFER_UDMA_0)
+		mask = 0x31c001ff;
+	else
+		mask = 0x303c0000;
+
+	timing = hpt37x_find_mode(ap, mode);
+
+	pci_read_config_dword(pdev, addr1, &reg);
+	reg = (reg & ~mask) | (timing & mask);
+	pci_write_config_dword(pdev, addr1, reg);
+}
+
+/**
+ *	hpt372_set_piomode		-	PIO setup
+ *	@ap: ATA interface
+ *	@adev: device on the interface
+ *
+ *	Perform PIO mode setup.
+ */
+
+static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	hpt372_set_mode(ap, adev, adev->pio_mode);
+}
+
+/**
+ *	hpt372_set_dmamode		-	DMA timing setup
+ *	@ap: ATA interface
+ *	@adev: Device being configured
+ *
+ *	Set up the channel for MWDMA or UDMA modes.
+ */
+
+static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+	hpt372_set_mode(ap, adev, adev->dma_mode);
+}
+
+/**
+ *	hpt37x_bmdma_end		-	DMA engine stop
+ *	@qc: ATA command
+ *
+ *	Clean up after the HPT372 and later DMA engine
+ */
+
+static void hpt37x_bmdma_stop(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	int mscreg = 0x50 + 4 * ap->port_no;
+	u8 bwsr_stat, msc_stat;
+
+	pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
+	pci_read_config_byte(pdev, mscreg, &msc_stat);
+	if (bwsr_stat & (1 << ap->port_no))
+		pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);
+	ata_bmdma_stop(qc);
+}
+
+
+static struct scsi_host_template hpt37x_sht = {
+	ATA_BMDMA_SHT(DRV_NAME),
+};
+
+/*
+ *	Configuration for HPT370
+ */
+
+static struct ata_port_operations hpt370_port_ops = {
+	.inherits	= &ata_bmdma_port_ops,
+
+	.bmdma_stop	= hpt370_bmdma_stop,
+
+	.mode_filter	= hpt370_filter,
+	.cable_detect	= hpt37x_cable_detect,
+	.set_piomode	= hpt370_set_piomode,
+	.set_dmamode	= hpt370_set_dmamode,
+	.prereset	= hpt37x_pre_reset,
+};
+
+/*
+ *	Configuration for HPT370A. Close to 370 but less filters
+ */
+
+static struct ata_port_operations hpt370a_port_ops = {
+	.inherits	= &hpt370_port_ops,
+	.mode_filter	= hpt370a_filter,
+};
+
+/*
+ *	Configuration for HPT371 and HPT302. Slightly different PIO and DMA
+ *	mode setting functionality.
+ */
+
+static struct ata_port_operations hpt302_port_ops = {
+	.inherits	= &ata_bmdma_port_ops,
+
+	.bmdma_stop	= hpt37x_bmdma_stop,
+
+	.cable_detect	= hpt37x_cable_detect,
+	.set_piomode	= hpt372_set_piomode,
+	.set_dmamode	= hpt372_set_dmamode,
+	.prereset	= hpt37x_pre_reset,
+};
+
+/*
+ *	Configuration for HPT372. Mode setting works like 371 and 302
+ *	but we have a mode filter.
+ */
+
+static struct ata_port_operations hpt372_port_ops = {
+	.inherits	= &hpt302_port_ops,
+	.mode_filter	= hpt372_filter,
+};
+
+/*
+ *	Configuration for HPT374. Mode setting and filtering works like 372
+ *	but we have a different cable detection procedure for function 1.
+ */
+
+static struct ata_port_operations hpt374_fn1_port_ops = {
+	.inherits	= &hpt372_port_ops,
+	.cable_detect	= hpt374_fn1_cable_detect,
+};
+
+/**
+ *	hpt37x_clock_slot	-	Turn timing to PC clock entry
+ *	@freq: Reported frequency timing
+ *	@base: Base timing
+ *
+ *	Turn the timing data intoa clock slot (0 for 33, 1 for 40, 2 for 50
+ *	and 3 for 66Mhz)
+ */
+
+static int hpt37x_clock_slot(unsigned int freq, unsigned int base)
+{
+	unsigned int f = (base * freq) / 192;	/* Mhz */
+	if (f < 40)
+		return 0;	/* 33Mhz slot */
+	if (f < 45)
+		return 1;	/* 40Mhz slot */
+	if (f < 55)
+		return 2;	/* 50Mhz slot */
+	return 3;		/* 60Mhz slot */
+}
+
+/**
+ *	hpt37x_calibrate_dpll		-	Calibrate the DPLL loop
+ *	@dev: PCI device
+ *
+ *	Perform a calibration cycle on the HPT37x DPLL. Returns 1 if this
+ *	succeeds
+ */
+
+static int hpt37x_calibrate_dpll(struct pci_dev *dev)
+{
+	u8 reg5b;
+	u32 reg5c;
+	int tries;
+
+	for (tries = 0; tries < 0x5000; tries++) {
+		udelay(50);
+		pci_read_config_byte(dev, 0x5b, &reg5b);
+		if (reg5b & 0x80) {
+			/* See if it stays set */
+			for (tries = 0; tries < 0x1000; tries++) {
+				pci_read_config_byte(dev, 0x5b, &reg5b);
+				/* Failed ? */
+				if ((reg5b & 0x80) == 0)
+					return 0;
+			}
+			/* Turn off tuning, we have the DPLL set */
+			pci_read_config_dword(dev, 0x5c, &reg5c);
+			pci_write_config_dword(dev, 0x5c, reg5c & ~0x100);
+			return 1;
+		}
+	}
+	/* Never went stable */
+	return 0;
+}
+
+static u32 hpt374_read_freq(struct pci_dev *pdev)
+{
+	u32 freq;
+	unsigned long io_base = pci_resource_start(pdev, 4);
+
+	if (PCI_FUNC(pdev->devfn) & 1) {
+		struct pci_dev *pdev_0;
+
+		pdev_0 = pci_get_slot(pdev->bus, pdev->devfn - 1);
+		/* Someone hot plugged the controller on us ? */
+		if (pdev_0 == NULL)
+			return 0;
+		io_base = pci_resource_start(pdev_0, 4);
+		freq = inl(io_base + 0x90);
+		pci_dev_put(pdev_0);
+	} else
+		freq = inl(io_base + 0x90);
+	return freq;
+}
+
+/**
+ *	hpt37x_init_one		-	Initialise an HPT37X/302
+ *	@dev: PCI device
+ *	@id: Entry in match table
+ *
+ *	Initialise an HPT37x device. There are some interesting complications
+ *	here. Firstly the chip may report 366 and be one of several variants.
+ *	Secondly all the timings depend on the clock for the chip which we must
+ *	detect and look up
+ *
+ *	This is the known chip mappings. It may be missing a couple of later
+ *	releases.
+ *
+ *	Chip version		PCI		Rev	Notes
+ *	HPT366			4 (HPT366)	0	Other driver
+ *	HPT366			4 (HPT366)	1	Other driver
+ *	HPT368			4 (HPT366)	2	Other driver
+ *	HPT370			4 (HPT366)	3	UDMA100
+ *	HPT370A			4 (HPT366)	4	UDMA100
+ *	HPT372			4 (HPT366)	5	UDMA133 (1)
+ *	HPT372N			4 (HPT366)	6	Other driver
+ *	HPT372A			5 (HPT372)	1	UDMA133 (1)
+ *	HPT372N			5 (HPT372)	2	Other driver
+ *	HPT302			6 (HPT302)	1	UDMA133
+ *	HPT302N			6 (HPT302)	2	Other driver
+ *	HPT371			7 (HPT371)	*	UDMA133
+ *	HPT374			8 (HPT374)	*	UDMA133 4 channel
+ *	HPT372N			9 (HPT372N)	*	Other driver
+ *
+ *	(1) UDMA133 support depends on the bus clock
+ */
+
+static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	/* HPT370 - UDMA100 */
+	static const struct ata_port_info info_hpt370 = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA5,
+		.port_ops = &hpt370_port_ops
+	};
+	/* HPT370A - UDMA100 */
+	static const struct ata_port_info info_hpt370a = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA5,
+		.port_ops = &hpt370a_port_ops
+	};
+	/* HPT370 - UDMA66 */
+	static const struct ata_port_info info_hpt370_33 = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA4,
+		.port_ops = &hpt370_port_ops
+	};
+	/* HPT370A - UDMA66 */
+	static const struct ata_port_info info_hpt370a_33 = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA4,
+		.port_ops = &hpt370a_port_ops
+	};
+	/* HPT372 - UDMA133 */
+	static const struct ata_port_info info_hpt372 = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA6,
+		.port_ops = &hpt372_port_ops
+	};
+	/* HPT371, 302 - UDMA133 */
+	static const struct ata_port_info info_hpt302 = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA6,
+		.port_ops = &hpt302_port_ops
+	};
+	/* HPT374 - UDMA100, function 1 uses different cable_detect method */
+	static const struct ata_port_info info_hpt374_fn0 = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA5,
+		.port_ops = &hpt372_port_ops
+	};
+	static const struct ata_port_info info_hpt374_fn1 = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA5,
+		.port_ops = &hpt374_fn1_port_ops
+	};
+
+	static const int MHz[4] = { 33, 40, 50, 66 };
+	void *private_data = NULL;
+	const struct ata_port_info *ppi[] = { NULL, NULL };
+	u8 rev = dev->revision;
+	u8 irqmask;
+	u8 mcr1;
+	u32 freq;
+	int prefer_dpll = 1;
+
+	unsigned long iobase = pci_resource_start(dev, 4);
+
+	const struct hpt_chip *chip_table;
+	int clock_slot;
+	int rc;
+
+	rc = pcim_enable_device(dev);
+	if (rc)
+		return rc;
+
+	switch (dev->device) {
+	case PCI_DEVICE_ID_TTI_HPT366:
+		/* May be a later chip in disguise. Check */
+		/* Older chips are in the HPT366 driver. Ignore them */
+		if (rev < 3)
+			return -ENODEV;
+		/* N series chips have their own driver. Ignore */
+		if (rev == 6)
+			return -ENODEV;
+
+		switch (rev) {
+		case 3:
+			ppi[0] = &info_hpt370;
+			chip_table = &hpt370;
+			prefer_dpll = 0;
+			break;
+		case 4:
+			ppi[0] = &info_hpt370a;
+			chip_table = &hpt370a;
+			prefer_dpll = 0;
+			break;
+		case 5:
+			ppi[0] = &info_hpt372;
+			chip_table = &hpt372;
+			break;
+		default:
+			pr_err("Unknown HPT366 subtype, please report (%d)\n",
+			       rev);
+			return -ENODEV;
+		}
+		break;
+	case PCI_DEVICE_ID_TTI_HPT372:
+		/* 372N if rev >= 2 */
+		if (rev >= 2)
+			return -ENODEV;
+		ppi[0] = &info_hpt372;
+		chip_table = &hpt372a;
+		break;
+	case PCI_DEVICE_ID_TTI_HPT302:
+		/* 302N if rev > 1 */
+		if (rev > 1)
+			return -ENODEV;
+		ppi[0] = &info_hpt302;
+		/* Check this */
+		chip_table = &hpt302;
+		break;
+	case PCI_DEVICE_ID_TTI_HPT371:
+		if (rev > 1)
+			return -ENODEV;
+		ppi[0] = &info_hpt302;
+		chip_table = &hpt371;
+		/*
+		 * Single channel device, master is not present but the BIOS
+		 * (or us for non x86) must mark it absent
+		 */
+		pci_read_config_byte(dev, 0x50, &mcr1);
+		mcr1 &= ~0x04;
+		pci_write_config_byte(dev, 0x50, mcr1);
+		break;
+	case PCI_DEVICE_ID_TTI_HPT374:
+		chip_table = &hpt374;
+		if (!(PCI_FUNC(dev->devfn) & 1))
+			*ppi = &info_hpt374_fn0;
+		else
+			*ppi = &info_hpt374_fn1;
+		break;
+	default:
+		pr_err("PCI table is bogus, please report (%d)\n", dev->device);
+		return -ENODEV;
+	}
+	/* Ok so this is a chip we support */
+
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+	pci_read_config_byte(dev, 0x5A, &irqmask);
+	irqmask &= ~0x10;
+	pci_write_config_byte(dev, 0x5a, irqmask);
+
+	/*
+	 * default to pci clock. make sure MA15/16 are set to output
+	 * to prevent drives having problems with 40-pin cables. Needed
+	 * for some drives such as IBM-DTLA which will not enter ready
+	 * state on reset when PDIAG is a input.
+	 */
+
+	pci_write_config_byte(dev, 0x5b, 0x23);
+
+	/*
+	 * HighPoint does this for HPT372A.
+	 * NOTE: This register is only writeable via I/O space.
+	 */
+	if (chip_table == &hpt372a)
+		outb(0x0e, iobase + 0x9c);
+
+	/*
+	 * Some devices do not let this value be accessed via PCI space
+	 * according to the old driver. In addition we must use the value
+	 * from FN 0 on the HPT374.
+	 */
+
+	if (chip_table == &hpt374) {
+		freq = hpt374_read_freq(dev);
+		if (freq == 0)
+			return -ENODEV;
+	} else
+		freq = inl(iobase + 0x90);
+
+	if ((freq >> 12) != 0xABCDE) {
+		int i;
+		u8 sr;
+		u32 total = 0;
+
+		pr_warn("BIOS has not set timing clocks\n");
+
+		/* This is the process the HPT371 BIOS is reported to use */
+		for (i = 0; i < 128; i++) {
+			pci_read_config_byte(dev, 0x78, &sr);
+			total += sr & 0x1FF;
+			udelay(15);
+		}
+		freq = total / 128;
+	}
+	freq &= 0x1FF;
+
+	/*
+	 *	Turn the frequency check into a band and then find a timing
+	 *	table to match it.
+	 */
+
+	clock_slot = hpt37x_clock_slot(freq, chip_table->base);
+	if (chip_table->clocks[clock_slot] == NULL || prefer_dpll) {
+		/*
+		 *	We need to try PLL mode instead
+		 *
+		 *	For non UDMA133 capable devices we should
+		 *	use a 50MHz DPLL by choice
+		 */
+		unsigned int f_low, f_high;
+		int dpll, adjust;
+
+		/* Compute DPLL */
+		dpll = (ppi[0]->udma_mask & 0xC0) ? 3 : 2;
+
+		f_low = (MHz[clock_slot] * 48) / MHz[dpll];
+		f_high = f_low + 2;
+		if (clock_slot > 1)
+			f_high += 2;
+
+		/* Select the DPLL clock. */
+		pci_write_config_byte(dev, 0x5b, 0x21);
+		pci_write_config_dword(dev, 0x5C,
+				       (f_high << 16) | f_low | 0x100);
+
+		for (adjust = 0; adjust < 8; adjust++) {
+			if (hpt37x_calibrate_dpll(dev))
+				break;
+			/*
+			 * See if it'll settle at a fractionally
+			 * different clock
+			 */
+			if (adjust & 1)
+				f_low -= adjust >> 1;
+			else
+				f_high += adjust >> 1;
+			pci_write_config_dword(dev, 0x5C,
+					       (f_high << 16) | f_low | 0x100);
+		}
+		if (adjust == 8) {
+			pr_err("DPLL did not stabilize!\n");
+			return -ENODEV;
+		}
+		if (dpll == 3)
+			private_data = (void *)hpt37x_timings_66;
+		else
+			private_data = (void *)hpt37x_timings_50;
+
+		pr_info("bus clock %dMHz, using %dMHz DPLL\n",
+			MHz[clock_slot], MHz[dpll]);
+	} else {
+		private_data = (void *)chip_table->clocks[clock_slot];
+		/*
+		 *	Perform a final fixup. Note that we will have used the
+		 *	DPLL on the HPT372 which means we don't have to worry
+		 *	about lack of UDMA133 support on lower clocks
+		 */
+
+		if (clock_slot < 2 && ppi[0] == &info_hpt370)
+			ppi[0] = &info_hpt370_33;
+		if (clock_slot < 2 && ppi[0] == &info_hpt370a)
+			ppi[0] = &info_hpt370a_33;
+
+		pr_info("%s using %dMHz bus clock\n",
+			chip_table->name, MHz[clock_slot]);
+	}
+
+	/* Now kick off ATA set up */
+	return ata_pci_bmdma_init_one(dev, ppi, &hpt37x_sht, private_data, 0);
+}
+
+static const struct pci_device_id hpt37x[] = {
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT374), },
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), },
+
+	{ },
+};
+
+static struct pci_driver hpt37x_pci_driver = {
+	.name		= DRV_NAME,
+	.id_table	= hpt37x,
+	.probe		= hpt37x_init_one,
+	.remove		= ata_pci_remove_one
+};
+
+module_pci_driver(hpt37x_pci_driver);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt37x);
+MODULE_VERSION(DRV_VERSION);