Initial import

1 files changed, 780 insertions, 0 deletions

diff --git a/drivers/crypto/caam/regs.h b/drivers/crypto/caam/regs.h
new file mode 100644
index 000000000..378ddc17f
--- /dev/null
+++ b/drivers/crypto/caam/regs.h
@@ -0,0 +1,780 @@
+/*
+ * CAAM hardware register-level view
+ *
+ * Copyright 2008-2011 Freescale Semiconductor, Inc.
+ */
+
+#ifndef REGS_H
+#define REGS_H
+
+#include <linux/types.h>
+#include <linux/io.h>
+
+/*
+ * Architecture-specific register access methods
+ *
+ * CAAM's bus-addressable registers are 64 bits internally.
+ * They have been wired to be safely accessible on 32-bit
+ * architectures, however. Registers were organized such
+ * that (a) they can be contained in 32 bits, (b) if not, then they
+ * can be treated as two 32-bit entities, or finally (c) if they
+ * must be treated as a single 64-bit value, then this can safely
+ * be done with two 32-bit cycles.
+ *
+ * For 32-bit operations on 64-bit values, CAAM follows the same
+ * 64-bit register access conventions as it's predecessors, in that
+ * writes are "triggered" by a write to the register at the numerically
+ * higher address, thus, a full 64-bit write cycle requires a write
+ * to the lower address, followed by a write to the higher address,
+ * which will latch/execute the write cycle.
+ *
+ * For example, let's assume a SW reset of CAAM through the master
+ * configuration register.
+ * - SWRST is in bit 31 of MCFG.
+ * - MCFG begins at base+0x0000.
+ * - Bits 63-32 are a 32-bit word at base+0x0000 (numerically-lower)
+ * - Bits 31-0 are a 32-bit word at base+0x0004 (numerically-higher)
+ *
+ * (and on Power, the convention is 0-31, 32-63, I know...)
+ *
+ * Assuming a 64-bit write to this MCFG to perform a software reset
+ * would then require a write of 0 to base+0x0000, followed by a
+ * write of 0x80000000 to base+0x0004, which would "execute" the
+ * reset.
+ *
+ * Of course, since MCFG 63-32 is all zero, we could cheat and simply
+ * write 0x8000000 to base+0x0004, and the reset would work fine.
+ * However, since CAAM does contain some write-and-read-intended
+ * 64-bit registers, this code defines 64-bit access methods for
+ * the sake of internal consistency and simplicity, and so that a
+ * clean transition to 64-bit is possible when it becomes necessary.
+ *
+ * There are limitations to this that the developer must recognize.
+ * 32-bit architectures cannot enforce an atomic-64 operation,
+ * Therefore:
+ *
+ * - On writes, since the HW is assumed to latch the cycle on the
+ *   write of the higher-numeric-address word, then ordered
+ *   writes work OK.
+ *
+ * - For reads, where a register contains a relevant value of more
+ *   that 32 bits, the hardware employs logic to latch the other
+ *   "half" of the data until read, ensuring an accurate value.
+ *   This is of particular relevance when dealing with CAAM's
+ *   performance counters.
+ *
+ */
+
+#ifdef __BIG_ENDIAN
+#define wr_reg32(reg, data) out_be32(reg, data)
+#define rd_reg32(reg) in_be32(reg)
+#ifdef CONFIG_64BIT
+#define wr_reg64(reg, data) out_be64(reg, data)
+#define rd_reg64(reg) in_be64(reg)
+#endif
+#else
+#ifdef __LITTLE_ENDIAN
+#define wr_reg32(reg, data) __raw_writel(data, reg)
+#define rd_reg32(reg) __raw_readl(reg)
+#ifdef CONFIG_64BIT
+#define wr_reg64(reg, data) __raw_writeq(data, reg)
+#define rd_reg64(reg) __raw_readq(reg)
+#endif
+#endif
+#endif
+
+#ifndef CONFIG_64BIT
+#ifdef __BIG_ENDIAN
+static inline void wr_reg64(u64 __iomem *reg, u64 data)
+{
+	wr_reg32((u32 __iomem *)reg, (data & 0xffffffff00000000ull) >> 32);
+	wr_reg32((u32 __iomem *)reg + 1, data & 0x00000000ffffffffull);
+}
+
+static inline u64 rd_reg64(u64 __iomem *reg)
+{
+	return (((u64)rd_reg32((u32 __iomem *)reg)) << 32) |
+		((u64)rd_reg32((u32 __iomem *)reg + 1));
+}
+#else
+#ifdef __LITTLE_ENDIAN
+static inline void wr_reg64(u64 __iomem *reg, u64 data)
+{
+	wr_reg32((u32 __iomem *)reg + 1, (data & 0xffffffff00000000ull) >> 32);
+	wr_reg32((u32 __iomem *)reg, data & 0x00000000ffffffffull);
+}
+
+static inline u64 rd_reg64(u64 __iomem *reg)
+{
+	return (((u64)rd_reg32((u32 __iomem *)reg + 1)) << 32) |
+		((u64)rd_reg32((u32 __iomem *)reg));
+}
+#endif
+#endif
+#endif
+
+/*
+ * jr_outentry
+ * Represents each entry in a JobR output ring
+ */
+struct jr_outentry {
+	dma_addr_t desc;/* Pointer to completed descriptor */
+	u32 jrstatus;	/* Status for completed descriptor */
+} __packed;
+
+/*
+ * caam_perfmon - Performance Monitor/Secure Memory Status/
+ *                CAAM Global Status/Component Version IDs
+ *
+ * Spans f00-fff wherever instantiated
+ */
+
+/* Number of DECOs */
+#define CHA_NUM_MS_DECONUM_SHIFT	24
+#define CHA_NUM_MS_DECONUM_MASK	(0xfull << CHA_NUM_MS_DECONUM_SHIFT)
+
+/* CHA Version IDs */
+#define CHA_ID_LS_AES_SHIFT	0
+#define CHA_ID_LS_AES_MASK		(0xfull << CHA_ID_LS_AES_SHIFT)
+
+#define CHA_ID_LS_DES_SHIFT	4
+#define CHA_ID_LS_DES_MASK		(0xfull << CHA_ID_LS_DES_SHIFT)
+
+#define CHA_ID_LS_ARC4_SHIFT	8
+#define CHA_ID_LS_ARC4_MASK	(0xfull << CHA_ID_LS_ARC4_SHIFT)
+
+#define CHA_ID_LS_MD_SHIFT	12
+#define CHA_ID_LS_MD_MASK	(0xfull << CHA_ID_LS_MD_SHIFT)
+
+#define CHA_ID_LS_RNG_SHIFT	16
+#define CHA_ID_LS_RNG_MASK	(0xfull << CHA_ID_LS_RNG_SHIFT)
+
+#define CHA_ID_LS_SNW8_SHIFT	20
+#define CHA_ID_LS_SNW8_MASK	(0xfull << CHA_ID_LS_SNW8_SHIFT)
+
+#define CHA_ID_LS_KAS_SHIFT	24
+#define CHA_ID_LS_KAS_MASK	(0xfull << CHA_ID_LS_KAS_SHIFT)
+
+#define CHA_ID_LS_PK_SHIFT	28
+#define CHA_ID_LS_PK_MASK	(0xfull << CHA_ID_LS_PK_SHIFT)
+
+#define CHA_ID_MS_CRC_SHIFT	0
+#define CHA_ID_MS_CRC_MASK	(0xfull << CHA_ID_MS_CRC_SHIFT)
+
+#define CHA_ID_MS_SNW9_SHIFT	4
+#define CHA_ID_MS_SNW9_MASK	(0xfull << CHA_ID_MS_SNW9_SHIFT)
+
+#define CHA_ID_MS_DECO_SHIFT	24
+#define CHA_ID_MS_DECO_MASK	(0xfull << CHA_ID_MS_DECO_SHIFT)
+
+#define CHA_ID_MS_JR_SHIFT	28
+#define CHA_ID_MS_JR_MASK	(0xfull << CHA_ID_MS_JR_SHIFT)
+
+struct sec_vid {
+	u16 ip_id;
+	u8 maj_rev;
+	u8 min_rev;
+};
+
+struct caam_perfmon {
+	/* Performance Monitor Registers			f00-f9f */
+	u64 req_dequeued;	/* PC_REQ_DEQ - Dequeued Requests	     */
+	u64 ob_enc_req;	/* PC_OB_ENC_REQ - Outbound Encrypt Requests */
+	u64 ib_dec_req;	/* PC_IB_DEC_REQ - Inbound Decrypt Requests  */
+	u64 ob_enc_bytes;	/* PC_OB_ENCRYPT - Outbound Bytes Encrypted  */
+	u64 ob_prot_bytes;	/* PC_OB_PROTECT - Outbound Bytes Protected  */
+	u64 ib_dec_bytes;	/* PC_IB_DECRYPT - Inbound Bytes Decrypted   */
+	u64 ib_valid_bytes;	/* PC_IB_VALIDATED Inbound Bytes Validated   */
+	u64 rsvd[13];
+
+	/* CAAM Hardware Instantiation Parameters		fa0-fbf */
+	u32 cha_rev_ms;		/* CRNR - CHA Rev No. Most significant half*/
+	u32 cha_rev_ls;		/* CRNR - CHA Rev No. Least significant half*/
+#define CTPR_MS_QI_SHIFT	25
+#define CTPR_MS_QI_MASK		(0x1ull << CTPR_MS_QI_SHIFT)
+#define CTPR_MS_VIRT_EN_INCL	0x00000001
+#define CTPR_MS_VIRT_EN_POR	0x00000002
+#define CTPR_MS_PG_SZ_MASK	0x10
+#define CTPR_MS_PG_SZ_SHIFT	4
+	u32 comp_parms_ms;	/* CTPR - Compile Parameters Register	*/
+	u32 comp_parms_ls;	/* CTPR - Compile Parameters Register	*/
+	u64 rsvd1[2];
+
+	/* CAAM Global Status					fc0-fdf */
+	u64 faultaddr;	/* FAR  - Fault Address		*/
+	u32 faultliodn;	/* FALR - Fault Address LIODN	*/
+	u32 faultdetail;	/* FADR - Fault Addr Detail	*/
+	u32 rsvd2;
+	u32 status;		/* CSTA - CAAM Status */
+	u64 rsvd3;
+
+	/* Component Instantiation Parameters			fe0-fff */
+	u32 rtic_id;		/* RVID - RTIC Version ID	*/
+	u32 ccb_id;		/* CCBVID - CCB Version ID	*/
+	u32 cha_id_ms;		/* CHAVID - CHA Version ID Most Significant*/
+	u32 cha_id_ls;		/* CHAVID - CHA Version ID Least Significant*/
+	u32 cha_num_ms;		/* CHANUM - CHA Number Most Significant	*/
+	u32 cha_num_ls;		/* CHANUM - CHA Number Least Significant*/
+	u32 caam_id_ms;		/* CAAMVID - CAAM Version ID MS	*/
+	u32 caam_id_ls;		/* CAAMVID - CAAM Version ID LS	*/
+};
+
+/* LIODN programming for DMA configuration */
+#define MSTRID_LOCK_LIODN	0x80000000
+#define MSTRID_LOCK_MAKETRUSTED	0x00010000	/* only for JR masterid */
+
+#define MSTRID_LIODN_MASK	0x0fff
+struct masterid {
+	u32 liodn_ms;	/* lock and make-trusted control bits */
+	u32 liodn_ls;	/* LIODN for non-sequence and seq access */
+};
+
+/* Partition ID for DMA configuration */
+struct partid {
+	u32 rsvd1;
+	u32 pidr;	/* partition ID, DECO */
+};
+
+/* RNGB test mode (replicated twice in some configurations) */
+/* Padded out to 0x100 */
+struct rngtst {
+	u32 mode;		/* RTSTMODEx - Test mode */
+	u32 rsvd1[3];
+	u32 reset;		/* RTSTRESETx - Test reset control */
+	u32 rsvd2[3];
+	u32 status;		/* RTSTSSTATUSx - Test status */
+	u32 rsvd3;
+	u32 errstat;		/* RTSTERRSTATx - Test error status */
+	u32 rsvd4;
+	u32 errctl;		/* RTSTERRCTLx - Test error control */
+	u32 rsvd5;
+	u32 entropy;		/* RTSTENTROPYx - Test entropy */
+	u32 rsvd6[15];
+	u32 verifctl;	/* RTSTVERIFCTLx - Test verification control */
+	u32 rsvd7;
+	u32 verifstat;	/* RTSTVERIFSTATx - Test verification status */
+	u32 rsvd8;
+	u32 verifdata;	/* RTSTVERIFDx - Test verification data */
+	u32 rsvd9;
+	u32 xkey;		/* RTSTXKEYx - Test XKEY */
+	u32 rsvd10;
+	u32 oscctctl;	/* RTSTOSCCTCTLx - Test osc. counter control */
+	u32 rsvd11;
+	u32 oscct;		/* RTSTOSCCTx - Test oscillator counter */
+	u32 rsvd12;
+	u32 oscctstat;	/* RTSTODCCTSTATx - Test osc counter status */
+	u32 rsvd13[2];
+	u32 ofifo[4];	/* RTSTOFIFOx - Test output FIFO */
+	u32 rsvd14[15];
+};
+
+/* RNG4 TRNG test registers */
+struct rng4tst {
+#define RTMCTL_PRGM	0x00010000	/* 1 -> program mode, 0 -> run mode */
+#define RTMCTL_SAMP_MODE_VON_NEUMANN_ES_SC	0 /* use von Neumann data in
+						     both entropy shifter and
+						     statistical checker */
+#define RTMCTL_SAMP_MODE_RAW_ES_SC		1 /* use raw data in both
+						     entropy shifter and
+						     statistical checker */
+#define RTMCTL_SAMP_MODE_VON_NEUMANN_ES_RAW_SC	2 /* use von Neumann data in
+						     entropy shifter, raw data
+						     in statistical checker */
+#define RTMCTL_SAMP_MODE_INVALID		3 /* invalid combination */
+	u32 rtmctl;		/* misc. control register */
+	u32 rtscmisc;		/* statistical check misc. register */
+	u32 rtpkrrng;		/* poker range register */
+	union {
+		u32 rtpkrmax;	/* PRGM=1: poker max. limit register */
+		u32 rtpkrsq;	/* PRGM=0: poker square calc. result register */
+	};
+#define RTSDCTL_ENT_DLY_SHIFT 16
+#define RTSDCTL_ENT_DLY_MASK (0xffff << RTSDCTL_ENT_DLY_SHIFT)
+#define RTSDCTL_ENT_DLY_MIN 3200
+#define RTSDCTL_ENT_DLY_MAX 12800
+	u32 rtsdctl;		/* seed control register */
+	union {
+		u32 rtsblim;	/* PRGM=1: sparse bit limit register */
+		u32 rttotsam;	/* PRGM=0: total samples register */
+	};
+	u32 rtfrqmin;		/* frequency count min. limit register */
+#define RTFRQMAX_DISABLE	(1 << 20)
+	union {
+		u32 rtfrqmax;	/* PRGM=1: freq. count max. limit register */
+		u32 rtfrqcnt;	/* PRGM=0: freq. count register */
+	};
+	u32 rsvd1[40];
+#define RDSTA_SKVT 0x80000000
+#define RDSTA_SKVN 0x40000000
+#define RDSTA_IF0 0x00000001
+#define RDSTA_IF1 0x00000002
+#define RDSTA_IFMASK (RDSTA_IF1 | RDSTA_IF0)
+	u32 rdsta;
+	u32 rsvd2[15];
+};
+
+/*
+ * caam_ctrl - basic core configuration
+ * starts base + 0x0000 padded out to 0x1000
+ */
+
+#define KEK_KEY_SIZE		8
+#define TKEK_KEY_SIZE		8
+#define TDSK_KEY_SIZE		8
+
+#define DECO_RESET	1	/* Use with DECO reset/availability regs */
+#define DECO_RESET_0	(DECO_RESET << 0)
+#define DECO_RESET_1	(DECO_RESET << 1)
+#define DECO_RESET_2	(DECO_RESET << 2)
+#define DECO_RESET_3	(DECO_RESET << 3)
+#define DECO_RESET_4	(DECO_RESET << 4)
+
+struct caam_ctrl {
+	/* Basic Configuration Section				000-01f */
+	/* Read/Writable					        */
+	u32 rsvd1;
+	u32 mcr;		/* MCFG      Master Config Register  */
+	u32 rsvd2;
+	u32 scfgr;		/* SCFGR, Security Config Register */
+
+	/* Bus Access Configuration Section			010-11f */
+	/* Read/Writable                                                */
+	struct masterid jr_mid[4];	/* JRxLIODNR - JobR LIODN setup */
+	u32 rsvd3[11];
+	u32 jrstart;			/* JRSTART - Job Ring Start Register */
+	struct masterid rtic_mid[4];	/* RTICxLIODNR - RTIC LIODN setup */
+	u32 rsvd4[5];
+	u32 deco_rsr;			/* DECORSR - Deco Request Source */
+	u32 rsvd11;
+	u32 deco_rq;			/* DECORR - DECO Request */
+	struct partid deco_mid[5];	/* DECOxLIODNR - 1 per DECO */
+	u32 rsvd5[22];
+
+	/* DECO Availability/Reset Section			120-3ff */
+	u32 deco_avail;		/* DAR - DECO availability */
+	u32 deco_reset;		/* DRR - DECO reset */
+	u32 rsvd6[182];
+
+	/* Key Encryption/Decryption Configuration              400-5ff */
+	/* Read/Writable only while in Non-secure mode                  */
+	u32 kek[KEK_KEY_SIZE];	/* JDKEKR - Key Encryption Key */
+	u32 tkek[TKEK_KEY_SIZE];	/* TDKEKR - Trusted Desc KEK */
+	u32 tdsk[TDSK_KEY_SIZE];	/* TDSKR - Trusted Desc Signing Key */
+	u32 rsvd7[32];
+	u64 sknonce;			/* SKNR - Secure Key Nonce */
+	u32 rsvd8[70];
+
+	/* RNG Test/Verification/Debug Access                   600-7ff */
+	/* (Useful in Test/Debug modes only...)                         */
+	union {
+		struct rngtst rtst[2];
+		struct rng4tst r4tst[2];
+	};
+
+	u32 rsvd9[448];
+
+	/* Performance Monitor                                  f00-fff */
+	struct caam_perfmon perfmon;
+};
+
+/*
+ * Controller master config register defs
+ */
+#define MCFGR_SWRESET		0x80000000 /* software reset */
+#define MCFGR_WDENABLE		0x40000000 /* DECO watchdog enable */
+#define MCFGR_WDFAIL		0x20000000 /* DECO watchdog force-fail */
+#define MCFGR_DMA_RESET		0x10000000
+#define MCFGR_LONG_PTR		0x00010000 /* Use >32-bit desc addressing */
+#define SCFGR_RDBENABLE		0x00000400
+#define SCFGR_VIRT_EN		0x00008000
+#define DECORR_RQD0ENABLE	0x00000001 /* Enable DECO0 for direct access */
+#define DECORSR_JR0		0x00000001 /* JR to supply TZ, SDID, ICID */
+#define DECORSR_VALID		0x80000000
+#define DECORR_DEN0		0x00010000 /* DECO0 available for access*/
+
+/* AXI read cache control */
+#define MCFGR_ARCACHE_SHIFT	12
+#define MCFGR_ARCACHE_MASK	(0xf << MCFGR_ARCACHE_SHIFT)
+
+/* AXI write cache control */
+#define MCFGR_AWCACHE_SHIFT	8
+#define MCFGR_AWCACHE_MASK	(0xf << MCFGR_AWCACHE_SHIFT)
+
+/* AXI pipeline depth */
+#define MCFGR_AXIPIPE_SHIFT	4
+#define MCFGR_AXIPIPE_MASK	(0xf << MCFGR_AXIPIPE_SHIFT)
+
+#define MCFGR_AXIPRI		0x00000008 /* Assert AXI priority sideband */
+#define MCFGR_BURST_64		0x00000001 /* Max burst size */
+
+/* JRSTART register offsets */
+#define JRSTART_JR0_START       0x00000001 /* Start Job ring 0 */
+#define JRSTART_JR1_START       0x00000002 /* Start Job ring 1 */
+#define JRSTART_JR2_START       0x00000004 /* Start Job ring 2 */
+#define JRSTART_JR3_START       0x00000008 /* Start Job ring 3 */
+
+/*
+ * caam_job_ring - direct job ring setup
+ * 1-4 possible per instantiation, base + 1000/2000/3000/4000
+ * Padded out to 0x1000
+ */
+struct caam_job_ring {
+	/* Input ring */
+	u64 inpring_base;	/* IRBAx -  Input desc ring baseaddr */
+	u32 rsvd1;
+	u32 inpring_size;	/* IRSx - Input ring size */
+	u32 rsvd2;
+	u32 inpring_avail;	/* IRSAx - Input ring room remaining */
+	u32 rsvd3;
+	u32 inpring_jobadd;	/* IRJAx - Input ring jobs added */
+
+	/* Output Ring */
+	u64 outring_base;	/* ORBAx - Output status ring base addr */
+	u32 rsvd4;
+	u32 outring_size;	/* ORSx - Output ring size */
+	u32 rsvd5;
+	u32 outring_rmvd;	/* ORJRx - Output ring jobs removed */
+	u32 rsvd6;
+	u32 outring_used;	/* ORSFx - Output ring slots full */
+
+	/* Status/Configuration */
+	u32 rsvd7;
+	u32 jroutstatus;	/* JRSTAx - JobR output status */
+	u32 rsvd8;
+	u32 jrintstatus;	/* JRINTx - JobR interrupt status */
+	u32 rconfig_hi;	/* JRxCFG - Ring configuration */
+	u32 rconfig_lo;
+
+	/* Indices. CAAM maintains as "heads" of each queue */
+	u32 rsvd9;
+	u32 inp_rdidx;	/* IRRIx - Input ring read index */
+	u32 rsvd10;
+	u32 out_wtidx;	/* ORWIx - Output ring write index */
+
+	/* Command/control */
+	u32 rsvd11;
+	u32 jrcommand;	/* JRCRx - JobR command */
+
+	u32 rsvd12[932];
+
+	/* Performance Monitor                                  f00-fff */
+	struct caam_perfmon perfmon;
+};
+
+#define JR_RINGSIZE_MASK	0x03ff
+/*
+ * jrstatus - Job Ring Output Status
+ * All values in lo word
+ * Also note, same values written out as status through QI
+ * in the command/status field of a frame descriptor
+ */
+#define JRSTA_SSRC_SHIFT            28
+#define JRSTA_SSRC_MASK             0xf0000000
+
+#define JRSTA_SSRC_NONE             0x00000000
+#define JRSTA_SSRC_CCB_ERROR        0x20000000
+#define JRSTA_SSRC_JUMP_HALT_USER   0x30000000
+#define JRSTA_SSRC_DECO             0x40000000
+#define JRSTA_SSRC_JRERROR          0x60000000
+#define JRSTA_SSRC_JUMP_HALT_CC     0x70000000
+
+#define JRSTA_DECOERR_JUMP          0x08000000
+#define JRSTA_DECOERR_INDEX_SHIFT   8
+#define JRSTA_DECOERR_INDEX_MASK    0xff00
+#define JRSTA_DECOERR_ERROR_MASK    0x00ff
+
+#define JRSTA_DECOERR_NONE          0x00
+#define JRSTA_DECOERR_LINKLEN       0x01
+#define JRSTA_DECOERR_LINKPTR       0x02
+#define JRSTA_DECOERR_JRCTRL        0x03
+#define JRSTA_DECOERR_DESCCMD       0x04
+#define JRSTA_DECOERR_ORDER         0x05
+#define JRSTA_DECOERR_KEYCMD        0x06
+#define JRSTA_DECOERR_LOADCMD       0x07
+#define JRSTA_DECOERR_STORECMD      0x08
+#define JRSTA_DECOERR_OPCMD         0x09
+#define JRSTA_DECOERR_FIFOLDCMD     0x0a
+#define JRSTA_DECOERR_FIFOSTCMD     0x0b
+#define JRSTA_DECOERR_MOVECMD       0x0c
+#define JRSTA_DECOERR_JUMPCMD       0x0d
+#define JRSTA_DECOERR_MATHCMD       0x0e
+#define JRSTA_DECOERR_SHASHCMD      0x0f
+#define JRSTA_DECOERR_SEQCMD        0x10
+#define JRSTA_DECOERR_DECOINTERNAL  0x11
+#define JRSTA_DECOERR_SHDESCHDR     0x12
+#define JRSTA_DECOERR_HDRLEN        0x13
+#define JRSTA_DECOERR_BURSTER       0x14
+#define JRSTA_DECOERR_DESCSIGNATURE 0x15
+#define JRSTA_DECOERR_DMA           0x16
+#define JRSTA_DECOERR_BURSTFIFO     0x17
+#define JRSTA_DECOERR_JRRESET       0x1a
+#define JRSTA_DECOERR_JOBFAIL       0x1b
+#define JRSTA_DECOERR_DNRERR        0x80
+#define JRSTA_DECOERR_UNDEFPCL      0x81
+#define JRSTA_DECOERR_PDBERR        0x82
+#define JRSTA_DECOERR_ANRPLY_LATE   0x83
+#define JRSTA_DECOERR_ANRPLY_REPLAY 0x84
+#define JRSTA_DECOERR_SEQOVF        0x85
+#define JRSTA_DECOERR_INVSIGN       0x86
+#define JRSTA_DECOERR_DSASIGN       0x87
+
+#define JRSTA_CCBERR_JUMP           0x08000000
+#define JRSTA_CCBERR_INDEX_MASK     0xff00
+#define JRSTA_CCBERR_INDEX_SHIFT    8
+#define JRSTA_CCBERR_CHAID_MASK     0x00f0
+#define JRSTA_CCBERR_CHAID_SHIFT    4
+#define JRSTA_CCBERR_ERRID_MASK     0x000f
+
+#define JRSTA_CCBERR_CHAID_AES      (0x01 << JRSTA_CCBERR_CHAID_SHIFT)
+#define JRSTA_CCBERR_CHAID_DES      (0x02 << JRSTA_CCBERR_CHAID_SHIFT)
+#define JRSTA_CCBERR_CHAID_ARC4     (0x03 << JRSTA_CCBERR_CHAID_SHIFT)
+#define JRSTA_CCBERR_CHAID_MD       (0x04 << JRSTA_CCBERR_CHAID_SHIFT)
+#define JRSTA_CCBERR_CHAID_RNG      (0x05 << JRSTA_CCBERR_CHAID_SHIFT)
+#define JRSTA_CCBERR_CHAID_SNOW     (0x06 << JRSTA_CCBERR_CHAID_SHIFT)
+#define JRSTA_CCBERR_CHAID_KASUMI   (0x07 << JRSTA_CCBERR_CHAID_SHIFT)
+#define JRSTA_CCBERR_CHAID_PK       (0x08 << JRSTA_CCBERR_CHAID_SHIFT)
+#define JRSTA_CCBERR_CHAID_CRC      (0x09 << JRSTA_CCBERR_CHAID_SHIFT)
+
+#define JRSTA_CCBERR_ERRID_NONE     0x00
+#define JRSTA_CCBERR_ERRID_MODE     0x01
+#define JRSTA_CCBERR_ERRID_DATASIZ  0x02
+#define JRSTA_CCBERR_ERRID_KEYSIZ   0x03
+#define JRSTA_CCBERR_ERRID_PKAMEMSZ 0x04
+#define JRSTA_CCBERR_ERRID_PKBMEMSZ 0x05
+#define JRSTA_CCBERR_ERRID_SEQUENCE 0x06
+#define JRSTA_CCBERR_ERRID_PKDIVZRO 0x07
+#define JRSTA_CCBERR_ERRID_PKMODEVN 0x08
+#define JRSTA_CCBERR_ERRID_KEYPARIT 0x09
+#define JRSTA_CCBERR_ERRID_ICVCHK   0x0a
+#define JRSTA_CCBERR_ERRID_HARDWARE 0x0b
+#define JRSTA_CCBERR_ERRID_CCMAAD   0x0c
+#define JRSTA_CCBERR_ERRID_INVCHA   0x0f
+
+#define JRINT_ERR_INDEX_MASK        0x3fff0000
+#define JRINT_ERR_INDEX_SHIFT       16
+#define JRINT_ERR_TYPE_MASK         0xf00
+#define JRINT_ERR_TYPE_SHIFT        8
+#define JRINT_ERR_HALT_MASK         0xc
+#define JRINT_ERR_HALT_SHIFT        2
+#define JRINT_ERR_HALT_INPROGRESS   0x4
+#define JRINT_ERR_HALT_COMPLETE     0x8
+#define JRINT_JR_ERROR              0x02
+#define JRINT_JR_INT                0x01
+
+#define JRINT_ERR_TYPE_WRITE        1
+#define JRINT_ERR_TYPE_BAD_INPADDR  3
+#define JRINT_ERR_TYPE_BAD_OUTADDR  4
+#define JRINT_ERR_TYPE_INV_INPWRT   5
+#define JRINT_ERR_TYPE_INV_OUTWRT   6
+#define JRINT_ERR_TYPE_RESET        7
+#define JRINT_ERR_TYPE_REMOVE_OFL   8
+#define JRINT_ERR_TYPE_ADD_OFL      9
+
+#define JRCFG_SOE		0x04
+#define JRCFG_ICEN		0x02
+#define JRCFG_IMSK		0x01
+#define JRCFG_ICDCT_SHIFT	8
+#define JRCFG_ICTT_SHIFT	16
+
+#define JRCR_RESET                  0x01
+
+/*
+ * caam_assurance - Assurance Controller View
+ * base + 0x6000 padded out to 0x1000
+ */
+
+struct rtic_element {
+	u64 address;
+	u32 rsvd;
+	u32 length;
+};
+
+struct rtic_block {
+	struct rtic_element element[2];
+};
+
+struct rtic_memhash {
+	u32 memhash_be[32];
+	u32 memhash_le[32];
+};
+
+struct caam_assurance {
+    /* Status/Command/Watchdog */
+	u32 rsvd1;
+	u32 status;		/* RSTA - Status */
+	u32 rsvd2;
+	u32 cmd;		/* RCMD - Command */
+	u32 rsvd3;
+	u32 ctrl;		/* RCTL - Control */
+	u32 rsvd4;
+	u32 throttle;	/* RTHR - Throttle */
+	u32 rsvd5[2];
+	u64 watchdog;	/* RWDOG - Watchdog Timer */
+	u32 rsvd6;
+	u32 rend;		/* REND - Endian corrections */
+	u32 rsvd7[50];
+
+	/* Block access/configuration @ 100/110/120/130 */
+	struct rtic_block memblk[4];	/* Memory Blocks A-D */
+	u32 rsvd8[32];
+
+	/* Block hashes @ 200/300/400/500 */
+	struct rtic_memhash hash[4];	/* Block hash values A-D */
+	u32 rsvd_3[640];
+};
+
+/*
+ * caam_queue_if - QI configuration and control
+ * starts base + 0x7000, padded out to 0x1000 long
+ */
+
+struct caam_queue_if {
+	u32 qi_control_hi;	/* QICTL  - QI Control */
+	u32 qi_control_lo;
+	u32 rsvd1;
+	u32 qi_status;	/* QISTA  - QI Status */
+	u32 qi_deq_cfg_hi;	/* QIDQC  - QI Dequeue Configuration */
+	u32 qi_deq_cfg_lo;
+	u32 qi_enq_cfg_hi;	/* QISEQC - QI Enqueue Command     */
+	u32 qi_enq_cfg_lo;
+	u32 rsvd2[1016];
+};
+
+/* QI control bits - low word */
+#define QICTL_DQEN      0x01              /* Enable frame pop          */
+#define QICTL_STOP      0x02              /* Stop dequeue/enqueue      */
+#define QICTL_SOE       0x04              /* Stop on error             */
+
+/* QI control bits - high word */
+#define QICTL_MBSI	0x01
+#define QICTL_MHWSI	0x02
+#define QICTL_MWSI	0x04
+#define QICTL_MDWSI	0x08
+#define QICTL_CBSI	0x10		/* CtrlDataByteSwapInput     */
+#define QICTL_CHWSI	0x20		/* CtrlDataHalfSwapInput     */
+#define QICTL_CWSI	0x40		/* CtrlDataWordSwapInput     */
+#define QICTL_CDWSI	0x80		/* CtrlDataDWordSwapInput    */
+#define QICTL_MBSO	0x0100
+#define QICTL_MHWSO	0x0200
+#define QICTL_MWSO	0x0400
+#define QICTL_MDWSO	0x0800
+#define QICTL_CBSO	0x1000		/* CtrlDataByteSwapOutput    */
+#define QICTL_CHWSO	0x2000		/* CtrlDataHalfSwapOutput    */
+#define QICTL_CWSO	0x4000		/* CtrlDataWordSwapOutput    */
+#define QICTL_CDWSO     0x8000		/* CtrlDataDWordSwapOutput   */
+#define QICTL_DMBS	0x010000
+#define QICTL_EPO	0x020000
+
+/* QI status bits */
+#define QISTA_PHRDERR   0x01              /* PreHeader Read Error      */
+#define QISTA_CFRDERR   0x02              /* Compound Frame Read Error */
+#define QISTA_OFWRERR   0x04              /* Output Frame Read Error   */
+#define QISTA_BPDERR    0x08              /* Buffer Pool Depleted      */
+#define QISTA_BTSERR    0x10              /* Buffer Undersize          */
+#define QISTA_CFWRERR   0x20              /* Compound Frame Write Err  */
+#define QISTA_STOPD     0x80000000        /* QI Stopped (see QICTL)    */
+
+/* deco_sg_table - DECO view of scatter/gather table */
+struct deco_sg_table {
+	u64 addr;		/* Segment Address */
+	u32 elen;		/* E, F bits + 30-bit length */
+	u32 bpid_offset;	/* Buffer Pool ID + 16-bit length */
+};
+
+/*
+ * caam_deco - descriptor controller - CHA cluster block
+ *
+ * Only accessible when direct DECO access is turned on
+ * (done in DECORR, via MID programmed in DECOxMID
+ *
+ * 5 typical, base + 0x8000/9000/a000/b000
+ * Padded out to 0x1000 long
+ */
+struct caam_deco {
+	u32 rsvd1;
+	u32 cls1_mode;	/* CxC1MR -  Class 1 Mode */
+	u32 rsvd2;
+	u32 cls1_keysize;	/* CxC1KSR - Class 1 Key Size */
+	u32 cls1_datasize_hi;	/* CxC1DSR - Class 1 Data Size */
+	u32 cls1_datasize_lo;
+	u32 rsvd3;
+	u32 cls1_icvsize;	/* CxC1ICVSR - Class 1 ICV size */
+	u32 rsvd4[5];
+	u32 cha_ctrl;	/* CCTLR - CHA control */
+	u32 rsvd5;
+	u32 irq_crtl;	/* CxCIRQ - CCB interrupt done/error/clear */
+	u32 rsvd6;
+	u32 clr_written;	/* CxCWR - Clear-Written */
+	u32 ccb_status_hi;	/* CxCSTA - CCB Status/Error */
+	u32 ccb_status_lo;
+	u32 rsvd7[3];
+	u32 aad_size;	/* CxAADSZR - Current AAD Size */
+	u32 rsvd8;
+	u32 cls1_iv_size;	/* CxC1IVSZR - Current Class 1 IV Size */
+	u32 rsvd9[7];
+	u32 pkha_a_size;	/* PKASZRx - Size of PKHA A */
+	u32 rsvd10;
+	u32 pkha_b_size;	/* PKBSZRx - Size of PKHA B */
+	u32 rsvd11;
+	u32 pkha_n_size;	/* PKNSZRx - Size of PKHA N */
+	u32 rsvd12;
+	u32 pkha_e_size;	/* PKESZRx - Size of PKHA E */
+	u32 rsvd13[24];
+	u32 cls1_ctx[16];	/* CxC1CTXR - Class 1 Context @100 */
+	u32 rsvd14[48];
+	u32 cls1_key[8];	/* CxC1KEYR - Class 1 Key @200 */
+	u32 rsvd15[121];
+	u32 cls2_mode;	/* CxC2MR - Class 2 Mode */
+	u32 rsvd16;
+	u32 cls2_keysize;	/* CxX2KSR - Class 2 Key Size */
+	u32 cls2_datasize_hi;	/* CxC2DSR - Class 2 Data Size */
+	u32 cls2_datasize_lo;
+	u32 rsvd17;
+	u32 cls2_icvsize;	/* CxC2ICVSZR - Class 2 ICV Size */
+	u32 rsvd18[56];
+	u32 cls2_ctx[18];	/* CxC2CTXR - Class 2 Context @500 */
+	u32 rsvd19[46];
+	u32 cls2_key[32];	/* CxC2KEYR - Class2 Key @600 */
+	u32 rsvd20[84];
+	u32 inp_infofifo_hi;	/* CxIFIFO - Input Info FIFO @7d0 */
+	u32 inp_infofifo_lo;
+	u32 rsvd21[2];
+	u64 inp_datafifo;	/* CxDFIFO - Input Data FIFO */
+	u32 rsvd22[2];
+	u64 out_datafifo;	/* CxOFIFO - Output Data FIFO */
+	u32 rsvd23[2];
+	u32 jr_ctl_hi;	/* CxJRR - JobR Control Register      @800 */
+	u32 jr_ctl_lo;
+	u64 jr_descaddr;	/* CxDADR - JobR Descriptor Address */
+#define DECO_OP_STATUS_HI_ERR_MASK 0xF00000FF
+	u32 op_status_hi;	/* DxOPSTA - DECO Operation Status */
+	u32 op_status_lo;
+	u32 rsvd24[2];
+	u32 liodn;		/* DxLSR - DECO LIODN Status - non-seq */
+	u32 td_liodn;	/* DxLSR - DECO LIODN Status - trustdesc */
+	u32 rsvd26[6];
+	u64 math[4];		/* DxMTH - Math register */
+	u32 rsvd27[8];
+	struct deco_sg_table gthr_tbl[4];	/* DxGTR - Gather Tables */
+	u32 rsvd28[16];
+	struct deco_sg_table sctr_tbl[4];	/* DxSTR - Scatter Tables */
+	u32 rsvd29[48];
+	u32 descbuf[64];	/* DxDESB - Descriptor buffer */
+	u32 rscvd30[193];
+#define DESC_DBG_DECO_STAT_HOST_ERR	0x00D00000
+#define DESC_DBG_DECO_STAT_VALID	0x80000000
+#define DESC_DBG_DECO_STAT_MASK		0x00F00000
+	u32 desc_dbg;		/* DxDDR - DECO Debug Register */
+	u32 rsvd31[126];
+};
+
+#define DECO_JQCR_WHL		0x20000000
+#define DECO_JQCR_FOUR		0x10000000
+
+#define JR_BLOCK_NUMBER		1
+#define ASSURE_BLOCK_NUMBER	6
+#define QI_BLOCK_NUMBER		7
+#define DECO_BLOCK_NUMBER	8
+#define PG_SIZE_4K		0x1000
+#define PG_SIZE_64K		0x10000
+#endif /* REGS_H */