Initial import

1 files changed, 154 insertions, 0 deletions

diff --git a/drivers/ide/dtc2278.c b/drivers/ide/dtc2278.c
new file mode 100644
index 000000000..8722df329
--- /dev/null
+++ b/drivers/ide/dtc2278.c
@@ -0,0 +1,154 @@
+/*
+ *  Copyright (C) 1996  Linus Torvalds & author (see below)
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/blkdev.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+#define DRV_NAME "dtc2278"
+
+/*
+ * Changing this #undef to #define may solve start up problems in some systems.
+ */
+#undef ALWAYS_SET_DTC2278_PIO_MODE
+
+/*
+ * From: andy@cercle.cts.com (Dyan Wile)
+ *
+ * Below is a patch for DTC-2278 - alike software-programmable controllers
+ * The code enables the secondary IDE controller and the PIO4 (3?) timings on
+ * the primary (EIDE). You may probably have to enable the 32-bit support to
+ * get the full speed. You better get the disk interrupts disabled ( hdparm -u0
+ * /dev/hd.. ) for the drives connected to the EIDE interface. (I get my
+ * filesystem  corrupted with -u1, but under heavy disk load only :-)
+ *
+ * This card is now forced to use the "serialize" feature,
+ * and irq-unmasking is disallowed.  If io_32bit is enabled,
+ * it must be done for BOTH drives on each interface.
+ *
+ * This code was written for the DTC2278E, but might work with any of these:
+ *
+ * DTC2278S has only a single IDE interface.
+ * DTC2278D has two IDE interfaces and is otherwise identical to the S version.
+ * DTC2278E also has serial ports and a printer port
+ * DTC2278EB: has onboard BIOS, and "works like a charm" -- Kent Bradford <kent@theory.caltech.edu>
+ *
+ * There may be a fourth controller type. The S and D versions use the
+ * Winbond chip, and I think the E version does also.
+ *
+ */
+
+static void sub22 (char b, char c)
+{
+	int i;
+
+	for(i = 0; i < 3; ++i) {
+		inb(0x3f6);
+		outb_p(b,0xb0);
+		inb(0x3f6);
+		outb_p(c,0xb4);
+		inb(0x3f6);
+		if(inb(0xb4) == c) {
+			outb_p(7,0xb0);
+			inb(0x3f6);
+			return;	/* success */
+		}
+	}
+}
+
+static DEFINE_SPINLOCK(dtc2278_lock);
+
+static void dtc2278_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+	unsigned long flags;
+
+	if (drive->pio_mode >= XFER_PIO_3) {
+		spin_lock_irqsave(&dtc2278_lock, flags);
+		/*
+		 * This enables PIO mode4 (3?) on the first interface
+		 */
+		sub22(1,0xc3);
+		sub22(0,0xa0);
+		spin_unlock_irqrestore(&dtc2278_lock, flags);
+	} else {
+		/* we don't know how to set it back again.. */
+		/* Actually we do - there is a data sheet available for the
+		   Winbond but does anyone actually care */
+	}
+}
+
+static const struct ide_port_ops dtc2278_port_ops = {
+	.set_pio_mode		= dtc2278_set_pio_mode,
+};
+
+static const struct ide_port_info dtc2278_port_info __initconst = {
+	.name			= DRV_NAME,
+	.chipset		= ide_dtc2278,
+	.port_ops		= &dtc2278_port_ops,
+	.host_flags		= IDE_HFLAG_SERIALIZE |
+				  IDE_HFLAG_NO_UNMASK_IRQS |
+				  IDE_HFLAG_IO_32BIT |
+				  /* disallow ->io_32bit changes */
+				  IDE_HFLAG_NO_IO_32BIT |
+				  IDE_HFLAG_NO_DMA |
+				  IDE_HFLAG_DTC2278,
+	.pio_mask		= ATA_PIO4,
+};
+
+static int __init dtc2278_probe(void)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	/*
+	 * This enables the second interface
+	 */
+	outb_p(4,0xb0);
+	inb(0x3f6);
+	outb_p(0x20,0xb4);
+	inb(0x3f6);
+#ifdef ALWAYS_SET_DTC2278_PIO_MODE
+	/*
+	 * This enables PIO mode4 (3?) on the first interface
+	 * and may solve start-up problems for some people.
+	 */
+	sub22(1,0xc3);
+	sub22(0,0xa0);
+#endif
+	local_irq_restore(flags);
+
+	return ide_legacy_device_add(&dtc2278_port_info, 0);
+}
+
+static bool probe_dtc2278;
+
+module_param_named(probe, probe_dtc2278, bool, 0);
+MODULE_PARM_DESC(probe, "probe for DTC2278xx chipsets");
+
+static int __init dtc2278_init(void)
+{
+	if (probe_dtc2278 == 0)
+		return -ENODEV;
+
+	if (dtc2278_probe()) {
+		printk(KERN_ERR "dtc2278: ide interfaces already in use!\n");
+		return -EBUSY;
+	}
+	return 0;
+}
+
+module_init(dtc2278_init);
+
+MODULE_AUTHOR("See Local File");
+MODULE_DESCRIPTION("support of DTC-2278 VLB IDE chipsets");
+MODULE_LICENSE("GPL");