Linux-libre 4.7.5-gnupck-4.7.5-gnu

14 files changed, 76 insertions, 36 deletions

diff --git a/drivers/iio/accel/bmc150-accel-core.c b/drivers/iio/accel/bmc150-accel-core.c
index 197e693e7..3833c83a4 100644
--- a/drivers/iio/accel/bmc150-accel-core.c
+++ b/drivers/iio/accel/bmc150-accel-core.c
@@ -67,6 +67,9 @@
 #define BMC150_ACCEL_REG_PMU_BW		0x10
 #define BMC150_ACCEL_DEF_BW			125
 
+#define BMC150_ACCEL_REG_RESET			0x14
+#define BMC150_ACCEL_RESET_VAL			0xB6
+
 #define BMC150_ACCEL_REG_INT_MAP_0		0x19
 #define BMC150_ACCEL_INT_MAP_0_BIT_SLOPE	BIT(2)
 
@@ -1497,6 +1500,14 @@ static int bmc150_accel_chip_init(struct bmc150_accel_data *data)
 	int ret, i;
 	unsigned int val;
 
+	/*
+	 * Reset chip to get it in a known good state. A delay of 1.8ms after
+	 * reset is required according to the data sheets of supported chips.
+	 */
+	regmap_write(data->regmap, BMC150_ACCEL_REG_RESET,
+		     BMC150_ACCEL_RESET_VAL);
+	usleep_range(1800, 2500);
+
 	ret = regmap_read(data->regmap, BMC150_ACCEL_REG_CHIP_ID, &val);
 	if (ret < 0) {
 		dev_err(dev, "Error: Reading chip id\n");
diff --git a/drivers/iio/accel/kxsd9.c b/drivers/iio/accel/kxsd9.c
index 3a9f10678..9d72d4bcf 100644
--- a/drivers/iio/accel/kxsd9.c
+++ b/drivers/iio/accel/kxsd9.c
@@ -160,11 +160,13 @@ static int kxsd9_read_raw(struct iio_dev *indio_dev,
 		if (ret < 0)
 			goto error_ret;
 		*val = ret;
+		ret = IIO_VAL_INT;
 		break;
 	case IIO_CHAN_INFO_SCALE:
 		ret = spi_w8r8(st->us, KXSD9_READ(KXSD9_REG_CTRL_C));
 		if (ret < 0)
 			goto error_ret;
+		*val = 0;
 		*val2 = kxsd9_micro_scales[ret & KXSD9_FS_MASK];
 		ret = IIO_VAL_INT_PLUS_MICRO;
 		break;
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 25378c588..f7232185d 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -377,6 +377,7 @@ config QCOM_SPMI_VADC
 config ROCKCHIP_SARADC
 	tristate "Rockchip SARADC driver"
 	depends on ARCH_ROCKCHIP || (ARM && COMPILE_TEST)
+	depends on RESET_CONTROLLER
 	help
 	  Say yes here to build support for the SARADC found in SoCs from
 	  Rockchip.
diff --git a/drivers/iio/adc/ad799x.c b/drivers/iio/adc/ad799x.c
index a3f5254f4..039622335 100644
--- a/drivers/iio/adc/ad799x.c
+++ b/drivers/iio/adc/ad799x.c
@@ -533,6 +533,7 @@ static struct attribute_group ad799x_event_attrs_group = {
 static const struct iio_info ad7991_info = {
 	.read_raw = &ad799x_read_raw,
 	.driver_module = THIS_MODULE,
+	.update_scan_mode = ad799x_update_scan_mode,
 };
 
 static const struct iio_info ad7993_4_7_8_noirq_info = {
diff --git a/drivers/iio/adc/at91_adc.c b/drivers/iio/adc/at91_adc.c
index 52430ba17..0438c6801 100644
--- a/drivers/iio/adc/at91_adc.c
+++ b/drivers/iio/adc/at91_adc.c
@@ -381,8 +381,8 @@ static irqreturn_t at91_adc_rl_interrupt(int irq, void *private)
 		st->ts_bufferedmeasure = false;
 		input_report_key(st->ts_input, BTN_TOUCH, 0);
 		input_sync(st->ts_input);
-	} else if (status & AT91_ADC_EOC(3)) {
-		/* Conversion finished */
+	} else if (status & AT91_ADC_EOC(3) && st->ts_input) {
+		/* Conversion finished and we've a touchscreen */
 		if (st->ts_bufferedmeasure) {
 			/*
 			 * Last measurement is always discarded, since it can
diff --git a/drivers/iio/adc/rockchip_saradc.c b/drivers/iio/adc/rockchip_saradc.c
index f9ad6c2d6..85d701291 100644
--- a/drivers/iio/adc/rockchip_saradc.c
+++ b/drivers/iio/adc/rockchip_saradc.c
@@ -21,6 +21,8 @@
 #include <linux/of_device.h>
 #include <linux/clk.h>
 #include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/reset.h>
 #include <linux/regulator/consumer.h>
 #include <linux/iio/iio.h>
 
@@ -53,6 +55,7 @@ struct rockchip_saradc {
 	struct clk		*clk;
 	struct completion	completion;
 	struct regulator	*vref;
+	struct reset_control	*reset;
 	const struct rockchip_saradc_data *data;
 	u16			last_val;
 };
@@ -190,6 +193,16 @@ static const struct of_device_id rockchip_saradc_match[] = {
 };
 MODULE_DEVICE_TABLE(of, rockchip_saradc_match);
 
+/**
+ * Reset SARADC Controller.
+ */
+static void rockchip_saradc_reset_controller(struct reset_control *reset)
+{
+	reset_control_assert(reset);
+	usleep_range(10, 20);
+	reset_control_deassert(reset);
+}
+
 static int rockchip_saradc_probe(struct platform_device *pdev)
 {
 	struct rockchip_saradc *info = NULL;
@@ -218,6 +231,20 @@ static int rockchip_saradc_probe(struct platform_device *pdev)
 	if (IS_ERR(info->regs))
 		return PTR_ERR(info->regs);
 
+	/*
+	 * The reset should be an optional property, as it should work
+	 * with old devicetrees as well
+	 */
+	info->reset = devm_reset_control_get(&pdev->dev, "saradc-apb");
+	if (IS_ERR(info->reset)) {
+		ret = PTR_ERR(info->reset);
+		if (ret != -ENOENT)
+			return ret;
+
+		dev_dbg(&pdev->dev, "no reset control found\n");
+		info->reset = NULL;
+	}
+
 	init_completion(&info->completion);
 
 	irq = platform_get_irq(pdev, 0);
@@ -252,6 +279,9 @@ static int rockchip_saradc_probe(struct platform_device *pdev)
 		return PTR_ERR(info->vref);
 	}
 
+	if (info->reset)
+		rockchip_saradc_reset_controller(info->reset);
+
 	/*
 	 * Use a default value for the converter clock.
 	 * This may become user-configurable in the future.
diff --git a/drivers/iio/adc/ti-ads1015.c b/drivers/iio/adc/ti-ads1015.c
index 73cbf0b54..fe96af605 100644
--- a/drivers/iio/adc/ti-ads1015.c
+++ b/drivers/iio/adc/ti-ads1015.c
@@ -403,7 +403,8 @@ static const struct iio_info ads1015_info = {
 #ifdef CONFIG_OF
 static int ads1015_get_channels_config_of(struct i2c_client *client)
 {
-	struct ads1015_data *data = i2c_get_clientdata(client);
+	struct iio_dev *indio_dev = i2c_get_clientdata(client);
+	struct ads1015_data *data = iio_priv(indio_dev);
 	struct device_node *node;
 
 	if (!client->dev.of_node ||
diff --git a/drivers/iio/adc/ti_am335x_adc.c b/drivers/iio/adc/ti_am335x_adc.c
index c1e05532d..0470fc843 100644
--- a/drivers/iio/adc/ti_am335x_adc.c
+++ b/drivers/iio/adc/ti_am335x_adc.c
@@ -32,6 +32,7 @@
 
 struct tiadc_device {
 	struct ti_tscadc_dev *mfd_tscadc;
+	struct mutex fifo1_lock; /* to protect fifo access */
 	int channels;
 	u8 channel_line[8];
 	u8 channel_step[8];
@@ -360,6 +361,7 @@ static int tiadc_read_raw(struct iio_dev *indio_dev,
 		int *val, int *val2, long mask)
 {
 	struct tiadc_device *adc_dev = iio_priv(indio_dev);
+	int ret = IIO_VAL_INT;
 	int i, map_val;
 	unsigned int fifo1count, read, stepid;
 	bool found = false;
@@ -373,13 +375,14 @@ static int tiadc_read_raw(struct iio_dev *indio_dev,
 	if (!step_en)
 		return -EINVAL;
 
+	mutex_lock(&adc_dev->fifo1_lock);
 	fifo1count = tiadc_readl(adc_dev, REG_FIFO1CNT);
 	while (fifo1count--)
 		tiadc_readl(adc_dev, REG_FIFO1);
 
 	am335x_tsc_se_set_once(adc_dev->mfd_tscadc, step_en);
 
-	timeout = jiffies + usecs_to_jiffies
+	timeout = jiffies + msecs_to_jiffies
 				(IDLE_TIMEOUT * adc_dev->channels);
 	/* Wait for Fifo threshold interrupt */
 	while (1) {
@@ -389,7 +392,8 @@ static int tiadc_read_raw(struct iio_dev *indio_dev,
 
 		if (time_after(jiffies, timeout)) {
 			am335x_tsc_se_adc_done(adc_dev->mfd_tscadc);
-			return -EAGAIN;
+			ret = -EAGAIN;
+			goto err_unlock;
 		}
 	}
 	map_val = adc_dev->channel_step[chan->scan_index];
@@ -415,8 +419,11 @@ static int tiadc_read_raw(struct iio_dev *indio_dev,
 	am335x_tsc_se_adc_done(adc_dev->mfd_tscadc);
 
 	if (found == false)
-		return -EBUSY;
-	return IIO_VAL_INT;
+		ret =  -EBUSY;
+
+err_unlock:
+	mutex_unlock(&adc_dev->fifo1_lock);
+	return ret;
 }
 
 static const struct iio_info tiadc_info = {
@@ -485,6 +492,7 @@ static int tiadc_probe(struct platform_device *pdev)
 
 	tiadc_step_config(indio_dev);
 	tiadc_writel(adc_dev, REG_FIFO1THR, FIFO1_THRESHOLD);
+	mutex_init(&adc_dev->fifo1_lock);
 
 	err = tiadc_channel_init(indio_dev, adc_dev->channels);
 	if (err < 0)
diff --git a/drivers/iio/common/hid-sensors/hid-sensor-attributes.c b/drivers/iio/common/hid-sensors/hid-sensor-attributes.c
index e81f43476..dc33c1dd5 100644
--- a/drivers/iio/common/hid-sensors/hid-sensor-attributes.c
+++ b/drivers/iio/common/hid-sensors/hid-sensor-attributes.c
@@ -56,8 +56,8 @@ static struct {
 	{HID_USAGE_SENSOR_ALS, 0, 1, 0},
 	{HID_USAGE_SENSOR_ALS, HID_USAGE_SENSOR_UNITS_LUX, 1, 0},
 
-	{HID_USAGE_SENSOR_PRESSURE, 0, 100000, 0},
-	{HID_USAGE_SENSOR_PRESSURE, HID_USAGE_SENSOR_UNITS_PASCAL, 1, 0},
+	{HID_USAGE_SENSOR_PRESSURE, 0, 100, 0},
+	{HID_USAGE_SENSOR_PRESSURE, HID_USAGE_SENSOR_UNITS_PASCAL, 0, 1000},
 };
 
 static int pow_10(unsigned power)
diff --git a/drivers/iio/humidity/am2315.c b/drivers/iio/humidity/am2315.c
index 11535911a..0ebced557 100644
--- a/drivers/iio/humidity/am2315.c
+++ b/drivers/iio/humidity/am2315.c
@@ -244,7 +244,7 @@ static int am2315_probe(struct i2c_client *client,
 	indio_dev->channels = am2315_channels;
 	indio_dev->num_channels = ARRAY_SIZE(am2315_channels);
 
-	ret = iio_triggered_buffer_setup(indio_dev, NULL,
+	ret = iio_triggered_buffer_setup(indio_dev, iio_pollfunc_store_time,
 					 am2315_trigger_handler, NULL);
 	if (ret < 0) {
 		dev_err(&client->dev, "iio triggered buffer setup failed\n");
diff --git a/drivers/iio/humidity/hdc100x.c b/drivers/iio/humidity/hdc100x.c
index a03832a5f..e0c9c70c2 100644
--- a/drivers/iio/humidity/hdc100x.c
+++ b/drivers/iio/humidity/hdc100x.c
@@ -142,7 +142,7 @@ static int hdc100x_get_measurement(struct hdc100x_data *data,
 	struct i2c_client *client = data->client;
 	int delay = data->adc_int_us[chan->address];
 	int ret;
-	int val;
+	__be16 val;
 
 	/* start measurement */
 	ret = i2c_smbus_write_byte(client, chan->address);
@@ -154,26 +154,13 @@ static int hdc100x_get_measurement(struct hdc100x_data *data,
 	/* wait for integration time to pass */
 	usleep_range(delay, delay + 1000);
 
-	/*
-	 * i2c_smbus_read_word_data cannot() be used here due to the command
-	 * value not being understood and causes NAKs preventing any reading
-	 * from being accessed.
-	 */
-	ret = i2c_smbus_read_byte(client);
+	/* read measurement */
+	ret = i2c_master_recv(data->client, (char *)&val, sizeof(val));
 	if (ret < 0) {
-		dev_err(&client->dev, "cannot read high byte measurement");
+		dev_err(&client->dev, "cannot read sensor data\n");
 		return ret;
 	}
-	val = ret << 8;
-
-	ret = i2c_smbus_read_byte(client);
-	if (ret < 0) {
-		dev_err(&client->dev, "cannot read low byte measurement");
-		return ret;
-	}
-	val |= ret;
-
-	return val;
+	return be16_to_cpu(val);
 }
 
 static int hdc100x_get_heater_status(struct hdc100x_data *data)
@@ -272,8 +259,8 @@ static int hdc100x_probe(struct i2c_client *client,
 	struct iio_dev *indio_dev;
 	struct hdc100x_data *data;
 
-	if (!i2c_check_functionality(client->adapter,
-				I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_BYTE))
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA |
+				     I2C_FUNC_SMBUS_BYTE | I2C_FUNC_I2C))
 		return -EOPNOTSUPP;
 
 	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
diff --git a/drivers/iio/industrialio-buffer.c b/drivers/iio/industrialio-buffer.c
index 49bf9c59f..158aaf44d 100644
--- a/drivers/iio/industrialio-buffer.c
+++ b/drivers/iio/industrialio-buffer.c
@@ -110,7 +110,7 @@ ssize_t iio_buffer_read_first_n_outer(struct file *filp, char __user *buf,
 	DEFINE_WAIT_FUNC(wait, woken_wake_function);
 	size_t datum_size;
 	size_t to_wait;
-	int ret;
+	int ret = 0;
 
 	if (!indio_dev->info)
 		return -ENODEV;
@@ -153,7 +153,7 @@ ssize_t iio_buffer_read_first_n_outer(struct file *filp, char __user *buf,
 		ret = rb->access->read_first_n(rb, n, buf);
 		if (ret == 0 && (filp->f_flags & O_NONBLOCK))
 			ret = -EAGAIN;
-	 } while (ret == 0);
+	} while (ret == 0);
 	remove_wait_queue(&rb->pollq, &wait);
 
 	return ret;
diff --git a/drivers/iio/industrialio-core.c b/drivers/iio/industrialio-core.c
index e6319a934..2e6a42758 100644
--- a/drivers/iio/industrialio-core.c
+++ b/drivers/iio/industrialio-core.c
@@ -532,9 +532,8 @@ ssize_t iio_format_value(char *buf, unsigned int type, int size, int *vals)
 			return sprintf(buf, "%d.%09u\n", vals[0], vals[1]);
 	case IIO_VAL_FRACTIONAL:
 		tmp = div_s64((s64)vals[0] * 1000000000LL, vals[1]);
-		vals[1] = do_div(tmp, 1000000000LL);
-		vals[0] = tmp;
-		return sprintf(buf, "%d.%09u\n", vals[0], vals[1]);
+		vals[0] = (int)div_s64_rem(tmp, 1000000000, &vals[1]);
+		return sprintf(buf, "%d.%09u\n", vals[0], abs(vals[1]));
 	case IIO_VAL_FRACTIONAL_LOG2:
 		tmp = (s64)vals[0] * 1000000000LL >> vals[1];
 		vals[1] = do_div(tmp, 1000000000LL);
diff --git a/drivers/iio/proximity/as3935.c b/drivers/iio/proximity/as3935.c
index e2f926cdc..a0aedda7d 100644
--- a/drivers/iio/proximity/as3935.c
+++ b/drivers/iio/proximity/as3935.c
@@ -392,7 +392,7 @@ static int as3935_probe(struct spi_device *spi)
 		return ret;
 	}
 
-	ret = iio_triggered_buffer_setup(indio_dev, NULL,
+	ret = iio_triggered_buffer_setup(indio_dev, iio_pollfunc_store_time,
 		&as3935_trigger_handler, NULL);
 
 	if (ret) {