Linux-libre 4.8.2-gnupck-4.8.2-gnu

46 files changed, 3935 insertions, 166 deletions

diff --git a/drivers/input/input-mt.c b/drivers/input/input-mt.c
index 54fce56c8..a1bbec9cd 100644
--- a/drivers/input/input-mt.c
+++ b/drivers/input/input-mt.c
@@ -218,8 +218,23 @@ void input_mt_report_pointer_emulation(struct input_dev *dev, bool use_count)
 	}
 
 	input_event(dev, EV_KEY, BTN_TOUCH, count > 0);
-	if (use_count)
+
+	if (use_count) {
+		if (count == 0 &&
+		    !test_bit(ABS_MT_DISTANCE, dev->absbit) &&
+		    test_bit(ABS_DISTANCE, dev->absbit) &&
+		    input_abs_get_val(dev, ABS_DISTANCE) != 0) {
+			/*
+			 * Force reporting BTN_TOOL_FINGER for devices that
+			 * only report general hover (and not per-contact
+			 * distance) when contact is in proximity but not
+			 * on the surface.
+			 */
+			count = 1;
+		}
+
 		input_mt_report_finger_count(dev, count);
+	}
 
 	if (oldest) {
 		int x = input_mt_get_value(oldest, ABS_MT_POSITION_X);
diff --git a/drivers/input/input.c b/drivers/input/input.c
index b87ffbd45..d95c34ee5 100644
--- a/drivers/input/input.c
+++ b/drivers/input/input.c
@@ -153,8 +153,6 @@ static void input_pass_values(struct input_dev *dev,
 
 	rcu_read_unlock();
 
-	add_input_randomness(vals->type, vals->code, vals->value);
-
 	/* trigger auto repeat for key events */
 	if (test_bit(EV_REP, dev->evbit) && test_bit(EV_KEY, dev->evbit)) {
 		for (v = vals; v != vals + count; v++) {
@@ -371,9 +369,10 @@ static int input_get_disposition(struct input_dev *dev,
 static void input_handle_event(struct input_dev *dev,
 			       unsigned int type, unsigned int code, int value)
 {
-	int disposition;
+	int disposition = input_get_disposition(dev, type, code, &value);
 
-	disposition = input_get_disposition(dev, type, code, &value);
+	if (disposition != INPUT_IGNORE_EVENT && type != EV_SYN)
+		add_input_randomness(type, code, value);
 
 	if ((disposition & INPUT_PASS_TO_DEVICE) && dev->event)
 		dev->event(dev, type, code, value);
diff --git a/drivers/input/joydev.c b/drivers/input/joydev.c
index e819a60b4..b30ab7e7a 100644
--- a/drivers/input/joydev.c
+++ b/drivers/input/joydev.c
@@ -979,6 +979,12 @@ static const struct input_device_id joydev_ids[] = {
 		.flags = INPUT_DEVICE_ID_MATCH_EVBIT |
 				INPUT_DEVICE_ID_MATCH_ABSBIT,
 		.evbit = { BIT_MASK(EV_ABS) },
+		.absbit = { BIT_MASK(ABS_Z) },
+	},
+	{
+		.flags = INPUT_DEVICE_ID_MATCH_EVBIT |
+				INPUT_DEVICE_ID_MATCH_ABSBIT,
+		.evbit = { BIT_MASK(EV_ABS) },
 		.absbit = { BIT_MASK(ABS_WHEEL) },
 	},
 	{
diff --git a/drivers/input/joystick/xpad.c b/drivers/input/joystick/xpad.c
index a529a4535..83af17ad0 100644
--- a/drivers/input/joystick/xpad.c
+++ b/drivers/input/joystick/xpad.c
@@ -115,6 +115,10 @@ static bool sticks_to_null;
 module_param(sticks_to_null, bool, S_IRUGO);
 MODULE_PARM_DESC(sticks_to_null, "Do not map sticks at all for unknown pads");
 
+static bool auto_poweroff = true;
+module_param(auto_poweroff, bool, S_IWUSR | S_IRUGO);
+MODULE_PARM_DESC(auto_poweroff, "Power off wireless controllers on suspend");
+
 static const struct xpad_device {
 	u16 idVendor;
 	u16 idProduct;
@@ -1248,6 +1252,36 @@ static void xpad_stop_input(struct usb_xpad *xpad)
 	usb_kill_urb(xpad->irq_in);
 }
 
+static void xpad360w_poweroff_controller(struct usb_xpad *xpad)
+{
+	unsigned long flags;
+	struct xpad_output_packet *packet =
+			&xpad->out_packets[XPAD_OUT_CMD_IDX];
+
+	spin_lock_irqsave(&xpad->odata_lock, flags);
+
+	packet->data[0] = 0x00;
+	packet->data[1] = 0x00;
+	packet->data[2] = 0x08;
+	packet->data[3] = 0xC0;
+	packet->data[4] = 0x00;
+	packet->data[5] = 0x00;
+	packet->data[6] = 0x00;
+	packet->data[7] = 0x00;
+	packet->data[8] = 0x00;
+	packet->data[9] = 0x00;
+	packet->data[10] = 0x00;
+	packet->data[11] = 0x00;
+	packet->len = 12;
+	packet->pending = true;
+
+	/* Reset the sequence so we send out poweroff now */
+	xpad->last_out_packet = -1;
+	xpad_try_sending_next_out_packet(xpad);
+
+	spin_unlock_irqrestore(&xpad->odata_lock, flags);
+}
+
 static int xpad360w_start_input(struct usb_xpad *xpad)
 {
 	int error;
@@ -1590,6 +1624,15 @@ static int xpad_suspend(struct usb_interface *intf, pm_message_t message)
 		 * or goes away.
 		 */
 		xpad360w_stop_input(xpad);
+
+		/*
+		 * The wireless adapter is going off now, so the
+		 * gamepads are going to become disconnected.
+		 * Unless explicitly disabled, power them down
+		 * so they don't just sit there flashing.
+		 */
+		if (auto_poweroff && xpad->pad_present)
+			xpad360w_poweroff_controller(xpad);
 	} else {
 		mutex_lock(&input->mutex);
 		if (input->users)
diff --git a/drivers/input/keyboard/clps711x-keypad.c b/drivers/input/keyboard/clps711x-keypad.c
index b637f1af8..997e3e97f 100644
--- a/drivers/input/keyboard/clps711x-keypad.c
+++ b/drivers/input/keyboard/clps711x-keypad.c
@@ -101,7 +101,7 @@ static int clps711x_keypad_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	priv->syscon =
-		syscon_regmap_lookup_by_compatible("cirrus,clps711x-syscon1");
+		syscon_regmap_lookup_by_compatible("cirrus,ep7209-syscon1");
 	if (IS_ERR(priv->syscon))
 		return PTR_ERR(priv->syscon);
 
@@ -181,7 +181,7 @@ static int clps711x_keypad_remove(struct platform_device *pdev)
 }
 
 static const struct of_device_id clps711x_keypad_of_match[] = {
-	{ .compatible = "cirrus,clps711x-keypad", },
+	{ .compatible = "cirrus,ep7209-keypad", },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, clps711x_keypad_of_match);
diff --git a/drivers/input/keyboard/cros_ec_keyb.c b/drivers/input/keyboard/cros_ec_keyb.c
index b01966dc7..4b0878f35 100644
--- a/drivers/input/keyboard/cros_ec_keyb.c
+++ b/drivers/input/keyboard/cros_ec_keyb.c
@@ -186,7 +186,7 @@ static irqreturn_t cros_ec_keyb_irq(int irq, void *data)
 	if (ret >= 0)
 		cros_ec_keyb_process(ckdev, kb_state, ret);
 	else
-		dev_err(ec->dev, "failed to get keyboard state: %d\n", ret);
+		dev_err(ckdev->dev, "failed to get keyboard state: %d\n", ret);
 
 	return IRQ_HANDLED;
 }
@@ -236,7 +236,7 @@ static void cros_ec_keyb_compute_valid_keys(struct cros_ec_keyb *ckdev)
 static int cros_ec_keyb_probe(struct platform_device *pdev)
 {
 	struct cros_ec_device *ec = dev_get_drvdata(pdev->dev.parent);
-	struct device *dev = ec->dev;
+	struct device *dev = &pdev->dev;
 	struct cros_ec_keyb *ckdev;
 	struct input_dev *idev;
 	struct device_node *np;
@@ -246,23 +246,22 @@ static int cros_ec_keyb_probe(struct platform_device *pdev)
 	if (!np)
 		return -ENODEV;
 
-	ckdev = devm_kzalloc(&pdev->dev, sizeof(*ckdev), GFP_KERNEL);
+	ckdev = devm_kzalloc(dev, sizeof(*ckdev), GFP_KERNEL);
 	if (!ckdev)
 		return -ENOMEM;
-	err = matrix_keypad_parse_of_params(&pdev->dev, &ckdev->rows,
-					    &ckdev->cols);
+	err = matrix_keypad_parse_of_params(dev, &ckdev->rows, &ckdev->cols);
 	if (err)
 		return err;
 
-	ckdev->valid_keys = devm_kzalloc(&pdev->dev, ckdev->cols, GFP_KERNEL);
+	ckdev->valid_keys = devm_kzalloc(dev, ckdev->cols, GFP_KERNEL);
 	if (!ckdev->valid_keys)
 		return -ENOMEM;
 
-	ckdev->old_kb_state = devm_kzalloc(&pdev->dev, ckdev->cols, GFP_KERNEL);
+	ckdev->old_kb_state = devm_kzalloc(dev, ckdev->cols, GFP_KERNEL);
 	if (!ckdev->old_kb_state)
 		return -ENOMEM;
 
-	idev = devm_input_allocate_device(&pdev->dev);
+	idev = devm_input_allocate_device(dev);
 	if (!idev)
 		return -ENOMEM;
 
@@ -273,7 +272,7 @@ static int cros_ec_keyb_probe(struct platform_device *pdev)
 
 	ckdev->ec = ec;
 	ckdev->dev = dev;
-	dev_set_drvdata(&pdev->dev, ckdev);
+	dev_set_drvdata(dev, ckdev);
 
 	idev->name = CROS_EC_DEV_NAME;
 	idev->phys = ec->phys_name;
@@ -282,7 +281,7 @@ static int cros_ec_keyb_probe(struct platform_device *pdev)
 	idev->id.bustype = BUS_VIRTUAL;
 	idev->id.version = 1;
 	idev->id.product = 0;
-	idev->dev.parent = &pdev->dev;
+	idev->dev.parent = dev;
 	idev->open = cros_ec_keyb_open;
 	idev->close = cros_ec_keyb_close;
 
diff --git a/drivers/input/keyboard/tc3589x-keypad.c b/drivers/input/keyboard/tc3589x-keypad.c
index e92dfd888..ec0070e97 100644
--- a/drivers/input/keyboard/tc3589x-keypad.c
+++ b/drivers/input/keyboard/tc3589x-keypad.c
@@ -32,7 +32,7 @@
 #define TC3589x_PULL_DOWN_MASK		0x1
 #define TC3589x_PULL_UP_MASK		0x2
 #define TC3589x_PULLUP_ALL_MASK		0xAA
-#define TC3589x_IO_PULL_VAL(index, mask)	((mask)<<((index)%4)*2))
+#define TC3589x_IO_PULL_VAL(index, mask)	((mask)<<((index)%4)*2)
 
 /* Bit masks for IOCFG register */
 #define IOCFG_BALLCFG		0x01
diff --git a/drivers/input/keyboard/tegra-kbc.c b/drivers/input/keyboard/tegra-kbc.c
index 29485bc42..0c07e1023 100644
--- a/drivers/input/keyboard/tegra-kbc.c
+++ b/drivers/input/keyboard/tegra-kbc.c
@@ -552,7 +552,7 @@ static int tegra_kbc_parse_dt(struct tegra_kbc *kbc)
 
 	if (!num_rows || !num_cols || ((num_rows + num_cols) > KBC_MAX_GPIO)) {
 		dev_err(kbc->dev,
-			"keypad rows/columns not porperly specified\n");
+			"keypad rows/columns not properly specified\n");
 		return -EINVAL;
 	}
 
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
index 1f2337abc..efb0ca871 100644
--- a/drivers/input/misc/Kconfig
+++ b/drivers/input/misc/Kconfig
@@ -82,6 +82,20 @@ config INPUT_ARIZONA_HAPTICS
 	  To compile this driver as a module, choose M here: the
 	  module will be called arizona-haptics.
 
+config INPUT_ATMEL_CAPTOUCH
+	tristate "Atmel Capacitive Touch Button Driver"
+	depends on OF || COMPILE_TEST
+	depends on I2C
+	help
+	  Say Y here if an Atmel Capacitive Touch Button device which
+	  implements "captouch" protocol is connected to I2C bus. Typically
+	  this device consists of Atmel Touch sensor controlled by AtMegaXX
+	  MCU running firmware based on Qtouch library.
+	  One should find "atmel,captouch" node in the board specific DTS.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called atmel_captouch.
+
 config INPUT_BMA150
 	tristate "BMA150/SMB380 acceleration sensor support"
 	depends on I2C
@@ -796,4 +810,13 @@ config INPUT_DRV2667_HAPTICS
 	  To compile this driver as a module, choose M here: the
 	  module will be called drv2667-haptics.
 
+config INPUT_HISI_POWERKEY
+	tristate "Hisilicon PMIC ONKEY support"
+	depends on ARCH_HISI || COMPILE_TEST
+	help
+	  Say Y to enable support for PMIC ONKEY.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called hisi_powerkey.
+
 endif
diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile
index 0357a088c..6a1e5e20f 100644
--- a/drivers/input/misc/Makefile
+++ b/drivers/input/misc/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_INPUT_APANEL)		+= apanel.o
 obj-$(CONFIG_INPUT_ARIZONA_HAPTICS)	+= arizona-haptics.o
 obj-$(CONFIG_INPUT_ATI_REMOTE2)		+= ati_remote2.o
 obj-$(CONFIG_INPUT_ATLAS_BTNS)		+= atlas_btns.o
+obj-$(CONFIG_INPUT_ATMEL_CAPTOUCH)	+= atmel_captouch.o
 obj-$(CONFIG_INPUT_BFIN_ROTARY)		+= bfin_rotary.o
 obj-$(CONFIG_INPUT_BMA150)		+= bma150.o
 obj-$(CONFIG_INPUT_CM109)		+= cm109.o
@@ -34,6 +35,7 @@ obj-$(CONFIG_INPUT_DRV2667_HAPTICS)	+= drv2667.o
 obj-$(CONFIG_INPUT_GP2A)		+= gp2ap002a00f.o
 obj-$(CONFIG_INPUT_GPIO_BEEPER)		+= gpio-beeper.o
 obj-$(CONFIG_INPUT_GPIO_TILT_POLLED)	+= gpio_tilt_polled.o
+obj-$(CONFIG_INPUT_HISI_POWERKEY)	+= hisi_powerkey.o
 obj-$(CONFIG_HP_SDC_RTC)		+= hp_sdc_rtc.o
 obj-$(CONFIG_INPUT_IMS_PCU)		+= ims-pcu.o
 obj-$(CONFIG_INPUT_IXP4XX_BEEPER)	+= ixp4xx-beeper.o
diff --git a/drivers/input/misc/apanel.c b/drivers/input/misc/apanel.c
index a8d2b8db4..53630afab 100644
--- a/drivers/input/misc/apanel.c
+++ b/drivers/input/misc/apanel.c
@@ -297,7 +297,7 @@ static int __init apanel_init(void)
 
 		if (slave != i2c_addr) {
 			pr_notice(APANEL ": only one SMBus slave "
-				  "address supported, skiping device...\n");
+				  "address supported, skipping device...\n");
 			continue;
 		}
 
diff --git a/drivers/input/misc/atmel_captouch.c b/drivers/input/misc/atmel_captouch.c
new file mode 100644
index 000000000..941265415
--- /dev/null
+++ b/drivers/input/misc/atmel_captouch.c
@@ -0,0 +1,290 @@
+/*
+ * Atmel Atmegaxx Capacitive Touch Button Driver
+ *
+ * Copyright (C) 2016 Google, inc.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/*
+ * It's irrelevant that the HW used to develop captouch driver is based
+ * on Atmega88PA part and uses QtouchADC parts for sensing touch.
+ * Calling this driver "captouch" is an arbitrary way to distinguish
+ * the protocol this driver supported by other atmel/qtouch drivers.
+ *
+ * Captouch driver supports a newer/different version of the I2C
+ * registers/commands than the qt1070.c driver.
+ * Don't let the similarity of the general driver structure fool you.
+ *
+ * For raw i2c access from userspace, use i2cset/i2cget
+ * to poke at /dev/i2c-N devices.
+ */
+
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+
+/* Maximum number of buttons supported */
+#define MAX_NUM_OF_BUTTONS		8
+
+/* Registers */
+#define REG_KEY1_THRESHOLD		0x02
+#define REG_KEY2_THRESHOLD		0x03
+#define REG_KEY3_THRESHOLD		0x04
+#define REG_KEY4_THRESHOLD		0x05
+
+#define REG_KEY1_REF_H			0x20
+#define REG_KEY1_REF_L			0x21
+#define REG_KEY2_REF_H			0x22
+#define REG_KEY2_REF_L			0x23
+#define REG_KEY3_REF_H			0x24
+#define REG_KEY3_REF_L			0x25
+#define REG_KEY4_REF_H			0x26
+#define REG_KEY4_REF_L			0x27
+
+#define REG_KEY1_DLT_H			0x30
+#define REG_KEY1_DLT_L			0x31
+#define REG_KEY2_DLT_H			0x32
+#define REG_KEY2_DLT_L			0x33
+#define REG_KEY3_DLT_H			0x34
+#define REG_KEY3_DLT_L			0x35
+#define REG_KEY4_DLT_H			0x36
+#define REG_KEY4_DLT_L			0x37
+
+#define REG_KEY_STATE			0x3C
+
+/*
+ * @i2c_client: I2C slave device client pointer
+ * @input: Input device pointer
+ * @num_btn: Number of buttons
+ * @keycodes: map of button# to KeyCode
+ * @prev_btn: Previous key state to detect button "press" or "release"
+ * @xfer_buf: I2C transfer buffer
+ */
+struct atmel_captouch_device {
+	struct i2c_client *client;
+	struct input_dev *input;
+	u32 num_btn;
+	u32 keycodes[MAX_NUM_OF_BUTTONS];
+	u8 prev_btn;
+	u8 xfer_buf[8] ____cacheline_aligned;
+};
+
+/*
+ * Read from I2C slave device
+ * The protocol is that the client has to provide both the register address
+ * and the length, and while reading back the device would prepend the data
+ * with address and length for verification.
+ */
+static int atmel_read(struct atmel_captouch_device *capdev,
+			 u8 reg, u8 *data, size_t len)
+{
+	struct i2c_client *client = capdev->client;
+	struct device *dev = &client->dev;
+	struct i2c_msg msg[2];
+	int err;
+
+	if (len > sizeof(capdev->xfer_buf) - 2)
+		return -EINVAL;
+
+	capdev->xfer_buf[0] = reg;
+	capdev->xfer_buf[1] = len;
+
+	msg[0].addr = client->addr;
+	msg[0].flags = 0;
+	msg[0].buf = capdev->xfer_buf;
+	msg[0].len = 2;
+
+	msg[1].addr = client->addr;
+	msg[1].flags = I2C_M_RD;
+	msg[1].buf = capdev->xfer_buf;
+	msg[1].len = len + 2;
+
+	err = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg));
+	if (err != ARRAY_SIZE(msg))
+		return err < 0 ? err : -EIO;
+
+	if (capdev->xfer_buf[0] != reg) {
+		dev_err(dev,
+			"I2C read error: register address does not match (%#02x vs %02x)\n",
+			capdev->xfer_buf[0], reg);
+		return -ECOMM;
+	}
+
+	memcpy(data, &capdev->xfer_buf[2], len);
+
+	return 0;
+}
+
+/*
+ * Handle interrupt and report the key changes to the input system.
+ * Multi-touch can be supported; however, it really depends on whether
+ * the device can multi-touch.
+ */
+static irqreturn_t atmel_captouch_isr(int irq, void *data)
+{
+	struct atmel_captouch_device *capdev = data;
+	struct device *dev = &capdev->client->dev;
+	int error;
+	int i;
+	u8 new_btn;
+	u8 changed_btn;
+
+	error = atmel_read(capdev, REG_KEY_STATE, &new_btn, 1);
+	if (error) {
+		dev_err(dev, "failed to read button state: %d\n", error);
+		goto out;
+	}
+
+	dev_dbg(dev, "%s: button state %#02x\n", __func__, new_btn);
+
+	changed_btn = new_btn ^ capdev->prev_btn;
+	capdev->prev_btn = new_btn;
+
+	for (i = 0; i < capdev->num_btn; i++) {
+		if (changed_btn & BIT(i))
+			input_report_key(capdev->input,
+					 capdev->keycodes[i],
+					 new_btn & BIT(i));
+	}
+
+	input_sync(capdev->input);
+
+out:
+	return IRQ_HANDLED;
+}
+
+/*
+ * Probe function to setup the device, input system and interrupt
+ */
+static int atmel_captouch_probe(struct i2c_client *client,
+		const struct i2c_device_id *id)
+{
+	struct atmel_captouch_device *capdev;
+	struct device *dev = &client->dev;
+	struct device_node *node;
+	int i;
+	int err;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_BYTE_DATA |
+					I2C_FUNC_SMBUS_WORD_DATA |
+					I2C_FUNC_SMBUS_I2C_BLOCK)) {
+		dev_err(dev, "needed i2c functionality is not supported\n");
+		return -EINVAL;
+	}
+
+	capdev = devm_kzalloc(dev, sizeof(*capdev), GFP_KERNEL);
+	if (!capdev)
+		return -ENOMEM;
+
+	capdev->client = client;
+	i2c_set_clientdata(client, capdev);
+
+	err = atmel_read(capdev, REG_KEY_STATE,
+			    &capdev->prev_btn, sizeof(capdev->prev_btn));
+	if (err) {
+		dev_err(dev, "failed to read initial button state: %d\n", err);
+		return err;
+	}
+
+	capdev->input = devm_input_allocate_device(dev);
+	if (!capdev->input) {
+		dev_err(dev, "failed to allocate input device\n");
+		return -ENOMEM;
+	}
+
+	capdev->input->id.bustype = BUS_I2C;
+	capdev->input->id.product = 0x880A;
+	capdev->input->id.version = 0;
+	capdev->input->name = "ATMegaXX Capacitive Button Controller";
+	__set_bit(EV_KEY, capdev->input->evbit);
+
+	node = dev->of_node;
+	if (!node) {
+		dev_err(dev, "failed to find matching node in device tree\n");
+		return -EINVAL;
+	}
+
+	if (of_property_read_bool(node, "autorepeat"))
+		__set_bit(EV_REP, capdev->input->evbit);
+
+	capdev->num_btn = of_property_count_u32_elems(node, "linux,keymap");
+	if (capdev->num_btn > MAX_NUM_OF_BUTTONS)
+		capdev->num_btn = MAX_NUM_OF_BUTTONS;
+
+	err = of_property_read_u32_array(node, "linux,keycodes",
+					 capdev->keycodes,
+					 capdev->num_btn);
+	if (err) {
+		dev_err(dev,
+			"failed to read linux,keycode property: %d\n", err);
+		return err;
+	}
+
+	for (i = 0; i < capdev->num_btn; i++)
+		__set_bit(capdev->keycodes[i], capdev->input->keybit);
+
+	capdev->input->keycode = capdev->keycodes;
+	capdev->input->keycodesize = sizeof(capdev->keycodes[0]);
+	capdev->input->keycodemax = capdev->num_btn;
+
+	err = input_register_device(capdev->input);
+	if (err)
+		return err;
+
+	err = devm_request_threaded_irq(dev, client->irq,
+					NULL, atmel_captouch_isr,
+					IRQF_ONESHOT,
+					"atmel_captouch", capdev);
+	if (err) {
+		dev_err(dev, "failed to request irq %d: %d\n",
+			client->irq, err);
+		return err;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id atmel_captouch_of_id[] = {
+	{
+		.compatible = "atmel,captouch",
+	},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, atmel_captouch_of_id);
+#endif
+
+static const struct i2c_device_id atmel_captouch_id[] = {
+	{ "atmel_captouch", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, atmel_captouch_id);
+
+static struct i2c_driver atmel_captouch_driver = {
+	.probe		= atmel_captouch_probe,
+	.id_table	= atmel_captouch_id,
+	.driver		= {
+		.name	= "atmel_captouch",
+		.of_match_table = of_match_ptr(atmel_captouch_of_id),
+	},
+};
+module_i2c_driver(atmel_captouch_driver);
+
+/* Module information */
+MODULE_AUTHOR("Hung-yu Wu <hywu@google.com>");
+MODULE_DESCRIPTION("Atmel ATmegaXX Capacitance Touch Sensor I2C Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/input/misc/hisi_powerkey.c b/drivers/input/misc/hisi_powerkey.c
new file mode 100644
index 000000000..675539c52
--- /dev/null
+++ b/drivers/input/misc/hisi_powerkey.c
@@ -0,0 +1,142 @@
+/*
+ * Hisilicon PMIC powerkey driver
+ *
+ * Copyright (C) 2013 Hisilicon Ltd.
+ * Copyright (C) 2015, 2016 Linaro Ltd.
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/reboot.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/input.h>
+#include <linux/slab.h>
+
+/* the held interrupt will trigger after 4 seconds */
+#define MAX_HELD_TIME	(4 * MSEC_PER_SEC)
+
+static irqreturn_t hi65xx_power_press_isr(int irq, void *q)
+{
+	struct input_dev *input = q;
+
+	pm_wakeup_event(input->dev.parent, MAX_HELD_TIME);
+	input_report_key(input, KEY_POWER, 1);
+	input_sync(input);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t hi65xx_power_release_isr(int irq, void *q)
+{
+	struct input_dev *input = q;
+
+	pm_wakeup_event(input->dev.parent, MAX_HELD_TIME);
+	input_report_key(input, KEY_POWER, 0);
+	input_sync(input);
+
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t hi65xx_restart_toggle_isr(int irq, void *q)
+{
+	struct input_dev *input = q;
+	int value = test_bit(KEY_RESTART, input->key);
+
+	pm_wakeup_event(input->dev.parent, MAX_HELD_TIME);
+	input_report_key(input, KEY_RESTART, !value);
+	input_sync(input);
+
+	return IRQ_HANDLED;
+}
+
+static const struct {
+	const char *name;
+	irqreturn_t (*handler)(int irq, void *q);
+} hi65xx_irq_info[] = {
+	{ "down", hi65xx_power_press_isr },
+	{ "up", hi65xx_power_release_isr },
+	{ "hold 4s", hi65xx_restart_toggle_isr },
+};
+
+static int hi65xx_powerkey_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct input_dev *input;
+	int irq, i, error;
+
+	input = devm_input_allocate_device(&pdev->dev);
+	if (!input) {
+		dev_err(&pdev->dev, "failed to allocate input device\n");
+		return -ENOMEM;
+	}
+
+	input->phys = "hisi_on/input0";
+	input->name = "HISI 65xx PowerOn Key";
+
+	input_set_capability(input, EV_KEY, KEY_POWER);
+	input_set_capability(input, EV_KEY, KEY_RESTART);
+
+	for (i = 0; i < ARRAY_SIZE(hi65xx_irq_info); i++) {
+
+		irq = platform_get_irq_byname(pdev, hi65xx_irq_info[i].name);
+		if (irq < 0) {
+			error = irq;
+			dev_err(dev, "couldn't get irq %s: %d\n",
+				hi65xx_irq_info[i].name, error);
+			return error;
+		}
+
+		error = devm_request_any_context_irq(dev, irq,
+						     hi65xx_irq_info[i].handler,
+						     IRQF_ONESHOT,
+						     hi65xx_irq_info[i].name,
+						     input);
+		if (error < 0) {
+			dev_err(dev, "couldn't request irq %s: %d\n",
+				hi65xx_irq_info[i].name, error);
+			return error;
+		}
+	}
+
+	error = input_register_device(input);
+	if (error) {
+		dev_err(&pdev->dev, "failed to register input device: %d\n",
+			error);
+		return error;
+	}
+
+	device_init_wakeup(&pdev->dev, 1);
+
+	return 0;
+}
+
+static int hi65xx_powerkey_remove(struct platform_device *pdev)
+{
+	device_init_wakeup(&pdev->dev, 0);
+
+	return 0;
+}
+
+static struct platform_driver hi65xx_powerkey_driver = {
+	.driver = {
+		.name = "hi65xx-powerkey",
+	},
+	.probe = hi65xx_powerkey_probe,
+	.remove  = hi65xx_powerkey_remove,
+};
+module_platform_driver(hi65xx_powerkey_driver);
+
+MODULE_AUTHOR("Zhiliang Xue <xuezhiliang@huawei.com");
+MODULE_DESCRIPTION("Hisi PMIC Power key driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/input/misc/regulator-haptic.c b/drivers/input/misc/regulator-haptic.c
index a804705eb..2e8f80193 100644
--- a/drivers/input/misc/regulator-haptic.c
+++ b/drivers/input/misc/regulator-haptic.c
@@ -124,7 +124,7 @@ regulator_haptic_parse_dt(struct device *dev, struct regulator_haptic *haptic)
 
 	node = dev->of_node;
 	if(!node) {
-		dev_err(dev, "Missing dveice tree data\n");
+		dev_err(dev, "Missing device tree data\n");
 		return -EINVAL;
 	}
 
diff --git a/drivers/input/misc/rotary_encoder.c b/drivers/input/misc/rotary_encoder.c
index c7fc8d4fb..1588aecaf 100644
--- a/drivers/input/misc/rotary_encoder.c
+++ b/drivers/input/misc/rotary_encoder.c
@@ -28,6 +28,11 @@
 
 #define DRV_NAME "rotary-encoder"
 
+enum rotary_encoder_encoding {
+	ROTENC_GRAY,
+	ROTENC_BINARY,
+};
+
 struct rotary_encoder {
 	struct input_dev *input;
 
@@ -37,6 +42,7 @@ struct rotary_encoder {
 	u32 axis;
 	bool relative_axis;
 	bool rollover;
+	enum rotary_encoder_encoding encoding;
 
 	unsigned int pos;
 
@@ -57,8 +63,9 @@ static unsigned int rotary_encoder_get_state(struct rotary_encoder *encoder)
 
 	for (i = 0; i < encoder->gpios->ndescs; ++i) {
 		int val = gpiod_get_value_cansleep(encoder->gpios->desc[i]);
+
 		/* convert from gray encoding to normal */
-		if (ret & 1)
+		if (encoder->encoding == ROTENC_GRAY && ret & 1)
 			val = !val;
 
 		ret = ret << 1 | val;
@@ -213,6 +220,20 @@ static int rotary_encoder_probe(struct platform_device *pdev)
 	encoder->rollover =
 		device_property_read_bool(dev, "rotary-encoder,rollover");
 
+	if (!device_property_present(dev, "rotary-encoder,encoding") ||
+	    !device_property_match_string(dev, "rotary-encoder,encoding",
+					  "gray")) {
+		dev_info(dev, "gray");
+		encoder->encoding = ROTENC_GRAY;
+	} else if (!device_property_match_string(dev, "rotary-encoder,encoding",
+						 "binary")) {
+		dev_info(dev, "binary");
+		encoder->encoding = ROTENC_BINARY;
+	} else {
+		dev_err(dev, "unknown encoding setting\n");
+		return -EINVAL;
+	}
+
 	device_property_read_u32(dev, "linux,axis", &encoder->axis);
 	encoder->relative_axis =
 		device_property_read_bool(dev, "rotary-encoder,relative-axis");
diff --git a/drivers/input/misc/xen-kbdfront.c b/drivers/input/misc/xen-kbdfront.c
index 0a9ad2cfb..227fbd2db 100644
--- a/drivers/input/misc/xen-kbdfront.c
+++ b/drivers/input/misc/xen-kbdfront.c
@@ -130,8 +130,8 @@ static int xenkbd_probe(struct xenbus_device *dev,
 	if (xenbus_scanf(XBT_NIL, dev->otherend, "feature-abs-pointer", "%d", &abs) < 0)
 		abs = 0;
 	if (abs) {
-		ret = xenbus_printf(XBT_NIL, dev->nodename,
-				    "request-abs-pointer", "1");
+		ret = xenbus_write(XBT_NIL, dev->nodename,
+				   "request-abs-pointer", "1");
 		if (ret) {
 			pr_warning("xenkbd: can't request abs-pointer");
 			abs = 0;
@@ -327,8 +327,8 @@ InitWait:
 		if (ret < 0)
 			val = 0;
 		if (val) {
-			ret = xenbus_printf(XBT_NIL, info->xbdev->nodename,
-					    "request-abs-pointer", "1");
+			ret = xenbus_write(XBT_NIL, info->xbdev->nodename,
+					   "request-abs-pointer", "1");
 			if (ret)
 				pr_warning("xenkbd: can't request abs-pointer");
 		}
diff --git a/drivers/input/mouse/elantech.c b/drivers/input/mouse/elantech.c
index be5b399da..08e252a42 100644
--- a/drivers/input/mouse/elantech.c
+++ b/drivers/input/mouse/elantech.c
@@ -222,12 +222,8 @@ static int elantech_write_reg(struct psmouse *psmouse, unsigned char reg,
  */
 static void elantech_packet_dump(struct psmouse *psmouse)
 {
-	int	i;
-
-	psmouse_printk(KERN_DEBUG, psmouse, "PS/2 packet [");
-	for (i = 0; i < psmouse->pktsize; i++)
-		printk("%s0x%02x ", i ? ", " : " ", psmouse->packet[i]);
-	printk("]\n");
+	psmouse_printk(KERN_DEBUG, psmouse, "PS/2 packet [%*ph]\n",
+		       psmouse->pktsize, psmouse->packet);
 }
 
 /*
@@ -1708,7 +1704,7 @@ int elantech_init(struct psmouse *psmouse)
 		snprintf(etd->tp_phys, sizeof(etd->tp_phys), "%s/input1",
 			psmouse->ps2dev.serio->phys);
 		tp_dev->phys = etd->tp_phys;
-		tp_dev->name = "Elantech PS/2 TrackPoint";
+		tp_dev->name = "ETPS/2 Elantech TrackPoint";
 		tp_dev->id.bustype = BUS_I8042;
 		tp_dev->id.vendor  = 0x0002;
 		tp_dev->id.product = PSMOUSE_ELANTECH;
diff --git a/drivers/input/mouse/lifebook.c b/drivers/input/mouse/lifebook.c
index e5ed21682..13d324cef 100644
--- a/drivers/input/mouse/lifebook.c
+++ b/drivers/input/mouse/lifebook.c
@@ -287,7 +287,7 @@ static int lifebook_create_relative_device(struct psmouse *psmouse)
 		 "%s/input1", psmouse->ps2dev.serio->phys);
 
 	dev2->phys = priv->phys;
-	dev2->name = "PS/2 Touchpad";
+	dev2->name = "LBPS/2 Fujitsu Lifebook Touchpad";
 	dev2->id.bustype = BUS_I8042;
 	dev2->id.vendor  = 0x0002;
 	dev2->id.product = PSMOUSE_LIFEBOOK;
diff --git a/drivers/input/rmi4/rmi_bus.c b/drivers/input/rmi4/rmi_bus.c
index 253df96be..a73580654 100644
--- a/drivers/input/rmi4/rmi_bus.c
+++ b/drivers/input/rmi4/rmi_bus.c
@@ -232,10 +232,7 @@ err_put_device:
 void rmi_unregister_function(struct rmi_function *fn)
 {
 	device_del(&fn->dev);
-
-	if (fn->dev.of_node)
-		of_node_put(fn->dev.of_node);
-
+	of_node_put(fn->dev.of_node);
 	put_device(&fn->dev);
 }
 
diff --git a/drivers/input/rmi4/rmi_f01.c b/drivers/input/rmi4/rmi_f01.c
index eb362bc71..fac81fc9b 100644
--- a/drivers/input/rmi4/rmi_f01.c
+++ b/drivers/input/rmi4/rmi_f01.c
@@ -81,26 +81,26 @@ struct f01_basic_properties {
  * This bit disables whatever sleep mode may be selected by the sleep_mode
  * field and forces the device to run at full power without sleeping.
  */
-#define RMI_F01_CRTL0_NOSLEEP_BIT	BIT(2)
+#define RMI_F01_CTRL0_NOSLEEP_BIT	BIT(2)
 
 /*
  * When this bit is set, the touch controller employs a noise-filtering
  * algorithm designed for use with a connected battery charger.
  */
-#define RMI_F01_CRTL0_CHARGER_BIT	BIT(5)
+#define RMI_F01_CTRL0_CHARGER_BIT	BIT(5)
 
 /*
  * Sets the report rate for the device. The effect of this setting is
  * highly product dependent. Check the spec sheet for your particular
  * touch sensor.
  */
-#define RMI_F01_CRTL0_REPORTRATE_BIT	BIT(6)
+#define RMI_F01_CTRL0_REPORTRATE_BIT	BIT(6)
 
 /*
  * Written by the host as an indicator that the device has been
  * successfully configured.
  */
-#define RMI_F01_CRTL0_CONFIGURED_BIT	BIT(7)
+#define RMI_F01_CTRL0_CONFIGURED_BIT	BIT(7)
 
 /**
  * @ctrl0 - see the bit definitions above.
@@ -330,10 +330,10 @@ static int rmi_f01_probe(struct rmi_function *fn)
 	case RMI_F01_NOSLEEP_DEFAULT:
 		break;
 	case RMI_F01_NOSLEEP_OFF:
-		f01->device_control.ctrl0 &= ~RMI_F01_CRTL0_NOSLEEP_BIT;
+		f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_NOSLEEP_BIT;
 		break;
 	case RMI_F01_NOSLEEP_ON:
-		f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+		f01->device_control.ctrl0 |= RMI_F01_CTRL0_NOSLEEP_BIT;
 		break;
 	}
 
@@ -349,7 +349,7 @@ static int rmi_f01_probe(struct rmi_function *fn)
 		f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
 	}
 
-	f01->device_control.ctrl0 |= RMI_F01_CRTL0_CONFIGURED_BIT;
+	f01->device_control.ctrl0 |= RMI_F01_CTRL0_CONFIGURED_BIT;
 
 	error = rmi_write(rmi_dev, fn->fd.control_base_addr,
 			  f01->device_control.ctrl0);
@@ -535,8 +535,8 @@ static int rmi_f01_suspend(struct rmi_function *fn)
 	int error;
 
 	f01->old_nosleep =
-		f01->device_control.ctrl0 & RMI_F01_CRTL0_NOSLEEP_BIT;
-	f01->device_control.ctrl0 &= ~RMI_F01_CRTL0_NOSLEEP_BIT;
+		f01->device_control.ctrl0 & RMI_F01_CTRL0_NOSLEEP_BIT;
+	f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_NOSLEEP_BIT;
 
 	f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
 	if (device_may_wakeup(fn->rmi_dev->xport->dev))
@@ -549,7 +549,7 @@ static int rmi_f01_suspend(struct rmi_function *fn)
 	if (error) {
 		dev_err(&fn->dev, "Failed to write sleep mode: %d.\n", error);
 		if (f01->old_nosleep)
-			f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+			f01->device_control.ctrl0 |= RMI_F01_CTRL0_NOSLEEP_BIT;
 		f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
 		f01->device_control.ctrl0 |= RMI_SLEEP_MODE_NORMAL;
 		return error;
@@ -564,7 +564,7 @@ static int rmi_f01_resume(struct rmi_function *fn)
 	int error;
 
 	if (f01->old_nosleep)
-		f01->device_control.ctrl0 |= RMI_F01_CRTL0_NOSLEEP_BIT;
+		f01->device_control.ctrl0 |= RMI_F01_CTRL0_NOSLEEP_BIT;
 
 	f01->device_control.ctrl0 &= ~RMI_F01_CTRL0_SLEEP_MODE_MASK;
 	f01->device_control.ctrl0 |= RMI_SLEEP_MODE_NORMAL;
diff --git a/drivers/input/rmi4/rmi_f11.c b/drivers/input/rmi4/rmi_f11.c
index ec8a10d53..20c7134b3 100644
--- a/drivers/input/rmi4/rmi_f11.c
+++ b/drivers/input/rmi4/rmi_f11.c
@@ -530,8 +530,8 @@ static void rmi_f11_rel_pos_report(struct f11_data *f11, u8 n_finger)
 	struct f11_2d_data *data = &f11->data;
 	s8 x, y;
 
-	x = data->rel_pos[n_finger * 2];
-	y = data->rel_pos[n_finger * 2 + 1];
+	x = data->rel_pos[n_finger * RMI_F11_REL_BYTES];
+	y = data->rel_pos[n_finger * RMI_F11_REL_BYTES + 1];
 
 	rmi_2d_sensor_rel_report(sensor, x, y);
 }
@@ -1241,7 +1241,6 @@ static int rmi_f11_attention(struct rmi_function *fn, unsigned long *irq_bits)
 	struct rmi_driver_data *drvdata = dev_get_drvdata(&rmi_dev->dev);
 	struct f11_data *f11 = dev_get_drvdata(&fn->dev);
 	u16 data_base_addr = fn->fd.data_base_addr;
-	u16 data_base_addr_offset = 0;
 	int error;
 
 	if (rmi_dev->xport->attn_data) {
@@ -1251,8 +1250,7 @@ static int rmi_f11_attention(struct rmi_function *fn, unsigned long *irq_bits)
 		rmi_dev->xport->attn_size -= f11->sensor.attn_size;
 	} else {
 		error = rmi_read_block(rmi_dev,
-				data_base_addr + data_base_addr_offset,
-				f11->sensor.data_pkt,
+				data_base_addr, f11->sensor.data_pkt,
 				f11->sensor.pkt_size);
 		if (error < 0)
 			return error;
@@ -1260,7 +1258,6 @@ static int rmi_f11_attention(struct rmi_function *fn, unsigned long *irq_bits)
 
 	rmi_f11_finger_handler(f11, &f11->sensor, irq_bits,
 				drvdata->num_of_irq_regs);
-	data_base_addr_offset += f11->sensor.pkt_size;
 
 	return 0;
 }
diff --git a/drivers/input/rmi4/rmi_f12.c b/drivers/input/rmi4/rmi_f12.c
index 88e91559c..332c02f0b 100644
--- a/drivers/input/rmi4/rmi_f12.c
+++ b/drivers/input/rmi4/rmi_f12.c
@@ -27,7 +27,6 @@ enum rmi_f12_object_type {
 };
 
 struct f12_data {
-	struct rmi_function *fn;
 	struct rmi_2d_sensor sensor;
 	struct rmi_2d_sensor_platform_data sensor_pdata;
 
diff --git a/drivers/input/rmi4/rmi_i2c.c b/drivers/input/rmi4/rmi_i2c.c
index a96a326b5..6f2e0e4f0 100644
--- a/drivers/input/rmi4/rmi_i2c.c
+++ b/drivers/input/rmi4/rmi_i2c.c
@@ -11,6 +11,8 @@
 #include <linux/rmi.h>
 #include <linux/irq.h>
 #include <linux/of.h>
+#include <linux/delay.h>
+#include <linux/regulator/consumer.h>
 #include "rmi_driver.h"
 
 #define BUFFER_SIZE_INCREMENT 32
@@ -37,6 +39,9 @@ struct rmi_i2c_xport {
 
 	u8 *tx_buf;
 	size_t tx_buf_size;
+
+	struct regulator_bulk_data supplies[2];
+	u32 startup_delay;
 };
 
 #define RMI_PAGE_SELECT_REGISTER 0xff
@@ -246,6 +251,24 @@ static int rmi_i2c_probe(struct i2c_client *client,
 		return -ENODEV;
 	}
 
+	rmi_i2c->supplies[0].supply = "vdd";
+	rmi_i2c->supplies[1].supply = "vio";
+	retval = devm_regulator_bulk_get(&client->dev,
+					 ARRAY_SIZE(rmi_i2c->supplies),
+					 rmi_i2c->supplies);
+	if (retval < 0)
+		return retval;
+
+	retval = regulator_bulk_enable(ARRAY_SIZE(rmi_i2c->supplies),
+				       rmi_i2c->supplies);
+	if (retval < 0)
+		return retval;
+
+	of_property_read_u32(client->dev.of_node, "syna,startup-delay-ms",
+			     &rmi_i2c->startup_delay);
+
+	msleep(rmi_i2c->startup_delay);
+
 	rmi_i2c->client = client;
 	mutex_init(&rmi_i2c->page_mutex);
 
@@ -286,6 +309,8 @@ static int rmi_i2c_remove(struct i2c_client *client)
 	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
 
 	rmi_unregister_transport_device(&rmi_i2c->xport);
+	regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+			       rmi_i2c->supplies);
 
 	return 0;
 }
@@ -308,6 +333,10 @@ static int rmi_i2c_suspend(struct device *dev)
 			dev_warn(dev, "Failed to enable irq for wake: %d\n",
 				ret);
 	}
+
+	regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+			       rmi_i2c->supplies);
+
 	return ret;
 }
 
@@ -317,6 +346,13 @@ static int rmi_i2c_resume(struct device *dev)
 	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
 	int ret;
 
+	ret = regulator_bulk_enable(ARRAY_SIZE(rmi_i2c->supplies),
+				    rmi_i2c->supplies);
+	if (ret)
+		return ret;
+
+	msleep(rmi_i2c->startup_delay);
+
 	enable_irq(rmi_i2c->irq);
 	if (device_may_wakeup(&client->dev)) {
 		ret = disable_irq_wake(rmi_i2c->irq);
@@ -346,6 +382,9 @@ static int rmi_i2c_runtime_suspend(struct device *dev)
 
 	disable_irq(rmi_i2c->irq);
 
+	regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+			       rmi_i2c->supplies);
+
 	return 0;
 }
 
@@ -355,6 +394,13 @@ static int rmi_i2c_runtime_resume(struct device *dev)
 	struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
 	int ret;
 
+	ret = regulator_bulk_enable(ARRAY_SIZE(rmi_i2c->supplies),
+				    rmi_i2c->supplies);
+	if (ret)
+		return ret;
+
+	msleep(rmi_i2c->startup_delay);
+
 	enable_irq(rmi_i2c->irq);
 
 	ret = rmi_driver_resume(rmi_i2c->xport.rmi_dev);
diff --git a/drivers/input/serio/ams_delta_serio.c b/drivers/input/serio/ams_delta_serio.c
index 45887e312..3df501c34 100644
--- a/drivers/input/serio/ams_delta_serio.c
+++ b/drivers/input/serio/ams_delta_serio.c
@@ -56,7 +56,7 @@ static int check_data(int data)
 	/* it should be odd */
 	if (!(parity & 0x01)) {
 		dev_warn(&ams_delta_serio->dev,
-				"paritiy check failed, data=0x%X parity=0x%X\n",
+				"parity check failed, data=0x%X parity=0x%X\n",
 				data, parity);
 		return SERIO_PARITY;
 	}
diff --git a/drivers/input/tablet/Kconfig b/drivers/input/tablet/Kconfig
index 623bb9e0d..a2b9f9742 100644
--- a/drivers/input/tablet/Kconfig
+++ b/drivers/input/tablet/Kconfig
@@ -73,6 +73,21 @@ config TABLET_USB_KBTAB
 	  To compile this driver as a module, choose M here: the
 	  module will be called kbtab.
 
+config TABLET_USB_PEGASUS
+	tristate "Pegasus Mobile Notetaker Pen input tablet support"
+	depends on USB_ARCH_HAS_HCD
+	select USB
+	help
+	  Say Y here if you want to use the Pegasus Mobile Notetaker,
+	  also known as:
+	  Genie e-note The Notetaker,
+	  Staedtler Digital ballpoint pen 990 01,
+	  IRISnotes Express or
+	  NEWLink Digital Note Taker.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called pegasus_notetaker.
+
 config TABLET_SERIAL_WACOM4
 	tristate "Wacom protocol 4 serial tablet support"
 	select SERIO
diff --git a/drivers/input/tablet/Makefile b/drivers/input/tablet/Makefile
index 2e130101c..200fc4e11 100644
--- a/drivers/input/tablet/Makefile
+++ b/drivers/input/tablet/Makefile
@@ -8,4 +8,5 @@ obj-$(CONFIG_TABLET_USB_AIPTEK)	+= aiptek.o
 obj-$(CONFIG_TABLET_USB_GTCO)	+= gtco.o
 obj-$(CONFIG_TABLET_USB_HANWANG) += hanwang.o
 obj-$(CONFIG_TABLET_USB_KBTAB)	+= kbtab.o
+obj-$(CONFIG_TABLET_USB_PEGASUS) += pegasus_notetaker.o
 obj-$(CONFIG_TABLET_SERIAL_WACOM4) += wacom_serial4.o
diff --git a/drivers/input/tablet/pegasus_notetaker.c b/drivers/input/tablet/pegasus_notetaker.c
new file mode 100644
index 000000000..949dacc78
--- /dev/null
+++ b/drivers/input/tablet/pegasus_notetaker.c
@@ -0,0 +1,450 @@
+/*
+ * Pegasus Mobile Notetaker Pen input tablet driver
+ *
+ * Copyright (c) 2016 Martin Kepplinger <martink@posteo.de>
+ */
+
+/*
+ * request packet (control endpoint):
+ * |-------------------------------------|
+ * | Report ID | Nr of bytes | command   |
+ * | (1 byte)  | (1 byte)    | (n bytes) |
+ * |-------------------------------------|
+ * | 0x02      | n           |           |
+ * |-------------------------------------|
+ *
+ * data packet after set xy mode command, 0x80 0xb5 0x02 0x01
+ * and pen is in range:
+ *
+ * byte	byte name		value (bits)
+ * --------------------------------------------
+ * 0	status			0 1 0 0 0 0 X X
+ * 1	color			0 0 0 0 H 0 S T
+ * 2	X low
+ * 3	X high
+ * 4	Y low
+ * 5	Y high
+ *
+ * X X	battery state:
+ *	no state reported	0x00
+ *	battery low		0x01
+ *	battery good		0x02
+ *
+ * H	Hovering
+ * S	Switch 1 (pen button)
+ * T	Tip
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/input.h>
+#include <linux/usb/input.h>
+#include <linux/slab.h>
+
+/* USB HID defines */
+#define USB_REQ_GET_REPORT		0x01
+#define USB_REQ_SET_REPORT		0x09
+
+#define USB_VENDOR_ID_PEGASUSTECH	0x0e20
+#define USB_DEVICE_ID_PEGASUS_NOTETAKER_EN100	0x0101
+
+/* device specific defines */
+#define NOTETAKER_REPORT_ID		0x02
+#define NOTETAKER_SET_CMD		0x80
+#define NOTETAKER_SET_MODE		0xb5
+
+#define NOTETAKER_LED_MOUSE		0x02
+#define PEN_MODE_XY			0x01
+
+#define SPECIAL_COMMAND			0x80
+#define BUTTON_PRESSED			0xb5
+#define COMMAND_VERSION			0xa9
+
+/* in xy data packet */
+#define BATTERY_NO_REPORT		0x40
+#define BATTERY_LOW			0x41
+#define BATTERY_GOOD			0x42
+#define PEN_BUTTON_PRESSED		BIT(1)
+#define PEN_TIP				BIT(0)
+
+struct pegasus {
+	unsigned char *data;
+	u8 data_len;
+	dma_addr_t data_dma;
+	struct input_dev *dev;
+	struct usb_device *usbdev;
+	struct usb_interface *intf;
+	struct urb *irq;
+	char name[128];
+	char phys[64];
+	struct work_struct init;
+};
+
+static int pegasus_control_msg(struct pegasus *pegasus, u8 *data, int len)
+{
+	const int sizeof_buf = len + 2;
+	int result;
+	int error;
+	u8 *cmd_buf;
+
+	cmd_buf = kmalloc(sizeof_buf, GFP_KERNEL);
+	if (!cmd_buf)
+		return -ENOMEM;
+
+	cmd_buf[0] = NOTETAKER_REPORT_ID;
+	cmd_buf[1] = len;
+	memcpy(cmd_buf + 2, data, len);
+
+	result = usb_control_msg(pegasus->usbdev,
+				 usb_sndctrlpipe(pegasus->usbdev, 0),
+				 USB_REQ_SET_REPORT,
+				 USB_TYPE_VENDOR | USB_DIR_OUT,
+				 0, 0, cmd_buf, sizeof_buf,
+				 USB_CTRL_SET_TIMEOUT);
+
+	kfree(cmd_buf);
+
+	if (unlikely(result != sizeof_buf)) {
+		error = result < 0 ? result : -EIO;
+		dev_err(&pegasus->usbdev->dev, "control msg error: %d\n",
+			error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int pegasus_set_mode(struct pegasus *pegasus, u8 mode, u8 led)
+{
+	u8 cmd[] = { NOTETAKER_SET_CMD, NOTETAKER_SET_MODE, led, mode };
+
+	return pegasus_control_msg(pegasus, cmd, sizeof(cmd));
+}
+
+static void pegasus_parse_packet(struct pegasus *pegasus)
+{
+	unsigned char *data = pegasus->data;
+	struct input_dev *dev = pegasus->dev;
+	u16 x, y;
+
+	switch (data[0]) {
+	case SPECIAL_COMMAND:
+		/* device button pressed */
+		if (data[1] == BUTTON_PRESSED)
+			schedule_work(&pegasus->init);
+
+		break;
+
+	/* xy data */
+	case BATTERY_LOW:
+		dev_warn_once(&dev->dev, "Pen battery low\n");
+		/* fall through */
+
+	case BATTERY_NO_REPORT:
+	case BATTERY_GOOD:
+		x = le16_to_cpup((__le16 *)&data[2]);
+		y = le16_to_cpup((__le16 *)&data[4]);
+
+		/* pen-up event */
+		if (x == 0 && y == 0)
+			break;
+
+		input_report_key(dev, BTN_TOUCH, data[1] & PEN_TIP);
+		input_report_key(dev, BTN_RIGHT, data[1] & PEN_BUTTON_PRESSED);
+		input_report_key(dev, BTN_TOOL_PEN, 1);
+		input_report_abs(dev, ABS_X, (s16)x);
+		input_report_abs(dev, ABS_Y, y);
+
+		input_sync(dev);
+		break;
+
+	default:
+		dev_warn_once(&pegasus->usbdev->dev,
+			      "unknown answer from device\n");
+	}
+}
+
+static void pegasus_irq(struct urb *urb)
+{
+	struct pegasus *pegasus = urb->context;
+	struct usb_device *dev = pegasus->usbdev;
+	int retval;
+
+	switch (urb->status) {
+	case 0:
+		pegasus_parse_packet(pegasus);
+		usb_mark_last_busy(pegasus->usbdev);
+		break;
+
+	case -ECONNRESET:
+	case -ENOENT:
+	case -ESHUTDOWN:
+		dev_err(&dev->dev, "%s - urb shutting down with status: %d",
+			__func__, urb->status);
+		return;
+
+	default:
+		dev_err(&dev->dev, "%s - nonzero urb status received: %d",
+			__func__, urb->status);
+		break;
+	}
+
+	retval = usb_submit_urb(urb, GFP_ATOMIC);
+	if (retval)
+		dev_err(&dev->dev, "%s - usb_submit_urb failed with result %d",
+			__func__, retval);
+}
+
+static void pegasus_init(struct work_struct *work)
+{
+	struct pegasus *pegasus = container_of(work, struct pegasus, init);
+	int error;
+
+	error = pegasus_set_mode(pegasus, PEN_MODE_XY, NOTETAKER_LED_MOUSE);
+	if (error)
+		dev_err(&pegasus->usbdev->dev, "pegasus_set_mode error: %d\n",
+			error);
+}
+
+static int pegasus_open(struct input_dev *dev)
+{
+	struct pegasus *pegasus = input_get_drvdata(dev);
+	int error;
+
+	error = usb_autopm_get_interface(pegasus->intf);
+	if (error)
+		return error;
+
+	pegasus->irq->dev = pegasus->usbdev;
+	if (usb_submit_urb(pegasus->irq, GFP_KERNEL)) {
+		error = -EIO;
+		goto err_autopm_put;
+	}
+
+	error = pegasus_set_mode(pegasus, PEN_MODE_XY, NOTETAKER_LED_MOUSE);
+	if (error)
+		goto err_kill_urb;
+
+	return 0;
+
+err_kill_urb:
+	usb_kill_urb(pegasus->irq);
+	cancel_work_sync(&pegasus->init);
+err_autopm_put:
+	usb_autopm_put_interface(pegasus->intf);
+	return error;
+}
+
+static void pegasus_close(struct input_dev *dev)
+{
+	struct pegasus *pegasus = input_get_drvdata(dev);
+
+	usb_kill_urb(pegasus->irq);
+	cancel_work_sync(&pegasus->init);
+	usb_autopm_put_interface(pegasus->intf);
+}
+
+static int pegasus_probe(struct usb_interface *intf,
+			 const struct usb_device_id *id)
+{
+	struct usb_device *dev = interface_to_usbdev(intf);
+	struct usb_endpoint_descriptor *endpoint;
+	struct pegasus *pegasus;
+	struct input_dev *input_dev;
+	int error;
+	int pipe;
+
+	/* We control interface 0 */
+	if (intf->cur_altsetting->desc.bInterfaceNumber >= 1)
+		return -ENODEV;
+
+	/* Sanity check that the device has an endpoint */
+	if (intf->altsetting[0].desc.bNumEndpoints < 1) {
+		dev_err(&intf->dev, "Invalid number of endpoints\n");
+		return -EINVAL;
+	}
+
+	endpoint = &intf->cur_altsetting->endpoint[0].desc;
+
+	pegasus = kzalloc(sizeof(*pegasus), GFP_KERNEL);
+	input_dev = input_allocate_device();
+	if (!pegasus || !input_dev) {
+		error = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	pegasus->usbdev = dev;
+	pegasus->dev = input_dev;
+	pegasus->intf = intf;
+
+	pipe = usb_rcvintpipe(dev, endpoint->bEndpointAddress);
+	pegasus->data_len = usb_maxpacket(dev, pipe, usb_pipeout(pipe));
+
+	pegasus->data = usb_alloc_coherent(dev, pegasus->data_len, GFP_KERNEL,
+					   &pegasus->data_dma);
+	if (!pegasus->data) {
+		error = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	pegasus->irq = usb_alloc_urb(0, GFP_KERNEL);
+	if (!pegasus->irq) {
+		error = -ENOMEM;
+		goto err_free_dma;
+	}
+
+	usb_fill_int_urb(pegasus->irq, dev, pipe,
+			 pegasus->data, pegasus->data_len,
+			 pegasus_irq, pegasus, endpoint->bInterval);
+
+	pegasus->irq->transfer_dma = pegasus->data_dma;
+	pegasus->irq->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+
+	if (dev->manufacturer)
+		strlcpy(pegasus->name, dev->manufacturer,
+			sizeof(pegasus->name));
+
+	if (dev->product) {
+		if (dev->manufacturer)
+			strlcat(pegasus->name, " ", sizeof(pegasus->name));
+		strlcat(pegasus->name, dev->product, sizeof(pegasus->name));
+	}
+
+	if (!strlen(pegasus->name))
+		snprintf(pegasus->name, sizeof(pegasus->name),
+			 "USB Pegasus Device %04x:%04x",
+			 le16_to_cpu(dev->descriptor.idVendor),
+			 le16_to_cpu(dev->descriptor.idProduct));
+
+	usb_make_path(dev, pegasus->phys, sizeof(pegasus->phys));
+	strlcat(pegasus->phys, "/input0", sizeof(pegasus->phys));
+
+	INIT_WORK(&pegasus->init, pegasus_init);
+
+	usb_set_intfdata(intf, pegasus);
+
+	input_dev->name = pegasus->name;
+	input_dev->phys = pegasus->phys;
+	usb_to_input_id(dev, &input_dev->id);
+	input_dev->dev.parent = &intf->dev;
+
+	input_set_drvdata(input_dev, pegasus);
+
+	input_dev->open = pegasus_open;
+	input_dev->close = pegasus_close;
+
+	__set_bit(EV_ABS, input_dev->evbit);
+	__set_bit(EV_KEY, input_dev->evbit);
+
+	__set_bit(ABS_X, input_dev->absbit);
+	__set_bit(ABS_Y, input_dev->absbit);
+
+	__set_bit(BTN_TOUCH, input_dev->keybit);
+	__set_bit(BTN_RIGHT, input_dev->keybit);
+	__set_bit(BTN_TOOL_PEN, input_dev->keybit);
+
+	__set_bit(INPUT_PROP_DIRECT, input_dev->propbit);
+	__set_bit(INPUT_PROP_POINTER, input_dev->propbit);
+
+	input_set_abs_params(input_dev, ABS_X, -1500, 1500, 8, 0);
+	input_set_abs_params(input_dev, ABS_Y, 1600, 3000, 8, 0);
+
+	error = input_register_device(pegasus->dev);
+	if (error)
+		goto err_free_urb;
+
+	return 0;
+
+err_free_urb:
+	usb_free_urb(pegasus->irq);
+err_free_dma:
+	usb_free_coherent(dev, pegasus->data_len,
+			  pegasus->data, pegasus->data_dma);
+err_free_mem:
+	input_free_device(input_dev);
+	kfree(pegasus);
+	usb_set_intfdata(intf, NULL);
+
+	return error;
+}
+
+static void pegasus_disconnect(struct usb_interface *intf)
+{
+	struct pegasus *pegasus = usb_get_intfdata(intf);
+
+	input_unregister_device(pegasus->dev);
+
+	usb_free_urb(pegasus->irq);
+	usb_free_coherent(interface_to_usbdev(intf),
+			  pegasus->data_len, pegasus->data,
+			  pegasus->data_dma);
+
+	kfree(pegasus);
+	usb_set_intfdata(intf, NULL);
+}
+
+static int pegasus_suspend(struct usb_interface *intf, pm_message_t message)
+{
+	struct pegasus *pegasus = usb_get_intfdata(intf);
+
+	mutex_lock(&pegasus->dev->mutex);
+	usb_kill_urb(pegasus->irq);
+	cancel_work_sync(&pegasus->init);
+	mutex_unlock(&pegasus->dev->mutex);
+
+	return 0;
+}
+
+static int pegasus_resume(struct usb_interface *intf)
+{
+	struct pegasus *pegasus = usb_get_intfdata(intf);
+	int retval = 0;
+
+	mutex_lock(&pegasus->dev->mutex);
+	if (pegasus->dev->users && usb_submit_urb(pegasus->irq, GFP_NOIO) < 0)
+		retval = -EIO;
+	mutex_unlock(&pegasus->dev->mutex);
+
+	return retval;
+}
+
+static int pegasus_reset_resume(struct usb_interface *intf)
+{
+	struct pegasus *pegasus = usb_get_intfdata(intf);
+	int retval = 0;
+
+	mutex_lock(&pegasus->dev->mutex);
+	if (pegasus->dev->users) {
+		retval = pegasus_set_mode(pegasus, PEN_MODE_XY,
+					  NOTETAKER_LED_MOUSE);
+		if (!retval && usb_submit_urb(pegasus->irq, GFP_NOIO) < 0)
+			retval = -EIO;
+	}
+	mutex_unlock(&pegasus->dev->mutex);
+
+	return retval;
+}
+
+static const struct usb_device_id pegasus_ids[] = {
+	{ USB_DEVICE(USB_VENDOR_ID_PEGASUSTECH,
+		     USB_DEVICE_ID_PEGASUS_NOTETAKER_EN100) },
+	{ }
+};
+MODULE_DEVICE_TABLE(usb, pegasus_ids);
+
+static struct usb_driver pegasus_driver = {
+	.name		= "pegasus_notetaker",
+	.probe		= pegasus_probe,
+	.disconnect	= pegasus_disconnect,
+	.suspend	= pegasus_suspend,
+	.resume		= pegasus_resume,
+	.reset_resume	= pegasus_reset_resume,
+	.id_table	= pegasus_ids,
+	.supports_autosuspend = 1,
+};
+
+module_usb_driver(pegasus_driver);
+
+MODULE_AUTHOR("Martin Kepplinger <martink@posteo.de>");
+MODULE_DESCRIPTION("Pegasus Mobile Notetaker Pen tablet driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 8ecdc38fd..2fb1f430a 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -632,7 +632,7 @@ config TOUCHSCREEN_EDT_FT5X06
 
 config TOUCHSCREEN_MIGOR
 	tristate "Renesas MIGO-R touchscreen"
-	depends on SH_MIGOR && I2C
+	depends on (SH_MIGOR || COMPILE_TEST) && I2C
 	help
 	  Say Y here to enable MIGO-R touchscreen support.
 
@@ -1046,6 +1046,44 @@ config TOUCHSCREEN_PCAP
 	  To compile this driver as a module, choose M here: the
 	  module will be called pcap_ts.
 
+config TOUCHSCREEN_RM_TS
+	tristate "Raydium I2C Touchscreen"
+	depends on I2C
+	depends on GPIOLIB || COMPILE_TEST
+	help
+	  Say Y here if you have Raydium series I2C touchscreen,
+	  such as RM32380, connected to your system.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called raydium_i2c_ts.
+
+config TOUCHSCREEN_SILEAD
+	tristate "Silead I2C touchscreen"
+	depends on I2C
+	help
+	  Say Y here if you have the Silead touchscreen connected to
+	  your system.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called silead.
+
+config TOUCHSCREEN_SIS_I2C
+	tristate "SiS 9200 family I2C touchscreen"
+	depends on I2C
+	select CRC_ITU_T
+	depends on GPIOLIB || COMPILE_TEST
+	help
+	  This enables support for SiS 9200 family over I2C based touchscreens.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called sis_i2c.
+
 config TOUCHSCREEN_ST1232
 	tristate "Sitronix ST1232 touchscreen controllers"
 	depends on I2C
@@ -1094,6 +1132,19 @@ config TOUCHSCREEN_SUR40
 	  To compile this driver as a module, choose M here: the
 	  module will be called sur40.
 
+config TOUCHSCREEN_SURFACE3_SPI
+	tristate "Ntrig/Microsoft Surface 3 SPI touchscreen"
+	depends on SPI
+	depends on GPIOLIB || COMPILE_TEST
+	help
+	  Say Y here if you have the Ntrig/Microsoft SPI touchscreen
+	  controller chip as found on the Surface 3 in your system.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called surface3_spi.
+
 config TOUCHSCREEN_SX8654
 	tristate "Semtech SX8654 touchscreen"
 	depends on I2C
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index f42975e71..b4373d6be 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -62,11 +62,15 @@ obj-$(CONFIG_TOUCHSCREEN_USB_COMPOSITE)	+= usbtouchscreen.o
 obj-$(CONFIG_TOUCHSCREEN_PCAP)		+= pcap_ts.o
 obj-$(CONFIG_TOUCHSCREEN_PENMOUNT)	+= penmount.o
 obj-$(CONFIG_TOUCHSCREEN_PIXCIR)	+= pixcir_i2c_ts.o
+obj-$(CONFIG_TOUCHSCREEN_RM_TS)		+= raydium_i2c_ts.o
 obj-$(CONFIG_TOUCHSCREEN_S3C2410)	+= s3c2410_ts.o
+obj-$(CONFIG_TOUCHSCREEN_SILEAD)	+= silead.o
+obj-$(CONFIG_TOUCHSCREEN_SIS_I2C)	+= sis_i2c.o
 obj-$(CONFIG_TOUCHSCREEN_ST1232)	+= st1232.o
 obj-$(CONFIG_TOUCHSCREEN_STMPE)		+= stmpe-ts.o
 obj-$(CONFIG_TOUCHSCREEN_SUN4I)		+= sun4i-ts.o
 obj-$(CONFIG_TOUCHSCREEN_SUR40)		+= sur40.o
+obj-$(CONFIG_TOUCHSCREEN_SURFACE3_SPI)	+= surface3_spi.o
 obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC)	+= ti_am335x_tsc.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213)	+= touchit213.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
diff --git a/drivers/input/touchscreen/ad7879.c b/drivers/input/touchscreen/ad7879.c
index e4bf1103e..e16a44667 100644
--- a/drivers/input/touchscreen/ad7879.c
+++ b/drivers/input/touchscreen/ad7879.c
@@ -595,7 +595,7 @@ struct ad7879 *ad7879_probe(struct device *dev, u8 devid, unsigned int irq,
 	} else {
 		input_set_abs_params(input_dev, ABS_X, 0, MAX_12BIT, 0, 0);
 		input_set_abs_params(input_dev, ABS_Y, 0, MAX_12BIT, 0, 0);
-		touchscreen_parse_properties(input_dev, false);
+		touchscreen_parse_properties(input_dev, false, NULL);
 		if (!input_abs_get_max(input_dev, ABS_PRESSURE)) {
 			dev_err(dev, "Touchscreen pressure is not specified\n");
 			return ERR_PTR(-EINVAL);
diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c
index a61b2153a..1ce3ecbe3 100644
--- a/drivers/input/touchscreen/ads7846.c
+++ b/drivers/input/touchscreen/ads7846.c
@@ -1473,7 +1473,6 @@ static int ads7846_remove(struct spi_device *spi)
 
 	ads784x_hwmon_unregister(spi, ts);
 
-	regulator_disable(ts->reg);
 	regulator_put(ts->reg);
 
 	if (!ts->get_pendown_state) {
diff --git a/drivers/input/touchscreen/chipone_icn8318.c b/drivers/input/touchscreen/chipone_icn8318.c
index 22a6fead8..0bf14067c 100644
--- a/drivers/input/touchscreen/chipone_icn8318.c
+++ b/drivers/input/touchscreen/chipone_icn8318.c
@@ -17,6 +17,7 @@
 #include <linux/i2c.h>
 #include <linux/input.h>
 #include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
 #include <linux/module.h>
 #include <linux/of.h>
 
@@ -52,11 +53,7 @@ struct icn8318_data {
 	struct i2c_client *client;
 	struct input_dev *input;
 	struct gpio_desc *wake_gpio;
-	u32 max_x;
-	u32 max_y;
-	bool invert_x;
-	bool invert_y;
-	bool swap_x_y;
+	struct touchscreen_properties prop;
 };
 
 static int icn8318_read_touch_data(struct i2c_client *client,
@@ -91,7 +88,7 @@ static irqreturn_t icn8318_irq(int irq, void *dev_id)
 	struct icn8318_data *data = dev_id;
 	struct device *dev = &data->client->dev;
 	struct icn8318_touch_data touch_data;
-	int i, ret, x, y;
+	int i, ret;
 
 	ret = icn8318_read_touch_data(data->client, &touch_data);
 	if (ret < 0) {
@@ -124,22 +121,9 @@ static irqreturn_t icn8318_irq(int irq, void *dev_id)
 		if (!act)
 			continue;
 
-		x = be16_to_cpu(touch->x);
-		y = be16_to_cpu(touch->y);
-
-		if (data->invert_x)
-			x = data->max_x - x;
-
-		if (data->invert_y)
-			y = data->max_y - y;
-
-		if (!data->swap_x_y) {
-			input_event(data->input, EV_ABS, ABS_MT_POSITION_X, x);
-			input_event(data->input, EV_ABS, ABS_MT_POSITION_Y, y);
-		} else {
-			input_event(data->input, EV_ABS, ABS_MT_POSITION_X, y);
-			input_event(data->input, EV_ABS, ABS_MT_POSITION_Y, x);
-		}
+		touchscreen_report_pos(data->input, &data->prop,
+				       be16_to_cpu(touch->x),
+				       be16_to_cpu(touch->y), true);
 	}
 
 	input_mt_sync_frame(data->input);
@@ -200,10 +184,8 @@ static int icn8318_probe(struct i2c_client *client,
 			 const struct i2c_device_id *id)
 {
 	struct device *dev = &client->dev;
-	struct device_node *np = dev->of_node;
 	struct icn8318_data *data;
 	struct input_dev *input;
-	u32 fuzz_x = 0, fuzz_y = 0;
 	int error;
 
 	if (!client->irq) {
@@ -223,19 +205,6 @@ static int icn8318_probe(struct i2c_client *client,
 		return error;
 	}
 
-	if (of_property_read_u32(np, "touchscreen-size-x", &data->max_x) ||
-	    of_property_read_u32(np, "touchscreen-size-y", &data->max_y)) {
-		dev_err(dev, "Error touchscreen-size-x and/or -y missing\n");
-		return -EINVAL;
-	}
-
-	/* Optional */
-	of_property_read_u32(np, "touchscreen-fuzz-x", &fuzz_x);
-	of_property_read_u32(np, "touchscreen-fuzz-y", &fuzz_y);
-	data->invert_x = of_property_read_bool(np, "touchscreen-inverted-x");
-	data->invert_y = of_property_read_bool(np, "touchscreen-inverted-y");
-	data->swap_x_y = of_property_read_bool(np, "touchscreen-swapped-x-y");
-
 	input = devm_input_allocate_device(dev);
 	if (!input)
 		return -ENOMEM;
@@ -246,16 +215,14 @@ static int icn8318_probe(struct i2c_client *client,
 	input->close = icn8318_stop;
 	input->dev.parent = dev;
 
-	if (!data->swap_x_y) {
-		input_set_abs_params(input, ABS_MT_POSITION_X, 0,
-				     data->max_x, fuzz_x, 0);
-		input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
-				     data->max_y, fuzz_y, 0);
-	} else {
-		input_set_abs_params(input, ABS_MT_POSITION_X, 0,
-				     data->max_y, fuzz_y, 0);
-		input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
-				     data->max_x, fuzz_x, 0);
+	input_set_capability(input, EV_ABS, ABS_MT_POSITION_X);
+	input_set_capability(input, EV_ABS, ABS_MT_POSITION_Y);
+
+	touchscreen_parse_properties(input, true, &data->prop);
+	if (!input_abs_get_max(input, ABS_MT_POSITION_X) ||
+	    !input_abs_get_max(input, ABS_MT_POSITION_Y)) {
+		dev_err(dev, "Error touchscreen-size-x and/or -y missing\n");
+		return -EINVAL;
 	}
 
 	error = input_mt_init_slots(input, ICN8318_MAX_TOUCHES,
diff --git a/drivers/input/touchscreen/cyttsp_core.c b/drivers/input/touchscreen/cyttsp_core.c
index 91cda8f81..79381cc17 100644
--- a/drivers/input/touchscreen/cyttsp_core.c
+++ b/drivers/input/touchscreen/cyttsp_core.c
@@ -657,7 +657,7 @@ struct cyttsp *cyttsp_probe(const struct cyttsp_bus_ops *bus_ops,
 
 	input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_X);
 	input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_Y);
-	touchscreen_parse_properties(input_dev, true);
+	touchscreen_parse_properties(input_dev, true, NULL);
 
 	error = input_mt_init_slots(input_dev, CY_MAX_ID, 0);
 	if (error) {
diff --git a/drivers/input/touchscreen/edt-ft5x06.c b/drivers/input/touchscreen/edt-ft5x06.c
index 23fbe382d..703e295a3 100644
--- a/drivers/input/touchscreen/edt-ft5x06.c
+++ b/drivers/input/touchscreen/edt-ft5x06.c
@@ -86,6 +86,7 @@ struct edt_reg_addr {
 struct edt_ft5x06_ts_data {
 	struct i2c_client *client;
 	struct input_dev *input;
+	struct touchscreen_properties prop;
 	u16 num_x;
 	u16 num_y;
 
@@ -246,8 +247,8 @@ static irqreturn_t edt_ft5x06_ts_isr(int irq, void *dev_id)
 		if (!down)
 			continue;
 
-		input_report_abs(tsdata->input, ABS_MT_POSITION_X, x);
-		input_report_abs(tsdata->input, ABS_MT_POSITION_Y, y);
+		touchscreen_report_pos(tsdata->input, &tsdata->prop, x, y,
+				       true);
 	}
 
 	input_mt_report_pointer_emulation(tsdata->input, true);
@@ -972,7 +973,7 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
 	input_set_abs_params(input, ABS_MT_POSITION_Y,
 			     0, tsdata->num_y * 64 - 1, 0, 0);
 
-	touchscreen_parse_properties(input, true);
+	touchscreen_parse_properties(input, true, &tsdata->prop);
 
 	error = input_mt_init_slots(input, tsdata->max_support_points,
 				INPUT_MT_DIRECT);
diff --git a/drivers/input/touchscreen/ili210x.c b/drivers/input/touchscreen/ili210x.c
index ddf694b9f..fe4848bd1 100644
--- a/drivers/input/touchscreen/ili210x.c
+++ b/drivers/input/touchscreen/ili210x.c
@@ -169,7 +169,7 @@ static ssize_t ili210x_calibrate(struct device *dev,
 
 	return count;
 }
-static DEVICE_ATTR(calibrate, 0644, NULL, ili210x_calibrate);
+static DEVICE_ATTR(calibrate, S_IWUSR, NULL, ili210x_calibrate);
 
 static struct attribute *ili210x_attributes[] = {
 	&dev_attr_calibrate.attr,
diff --git a/drivers/input/touchscreen/migor_ts.c b/drivers/input/touchscreen/migor_ts.c
index c038db93e..02fb11985 100644
--- a/drivers/input/touchscreen/migor_ts.c
+++ b/drivers/input/touchscreen/migor_ts.c
@@ -202,7 +202,7 @@ static int migor_ts_remove(struct i2c_client *client)
 	return 0;
 }
 
-static int migor_ts_suspend(struct device *dev)
+static int __maybe_unused migor_ts_suspend(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct migor_ts_priv *priv = i2c_get_clientdata(client);
@@ -213,7 +213,7 @@ static int migor_ts_suspend(struct device *dev)
 	return 0;
 }
 
-static int migor_ts_resume(struct device *dev)
+static int __maybe_unused migor_ts_resume(struct device *dev)
 {
 	struct i2c_client *client = to_i2c_client(dev);
 	struct migor_ts_priv *priv = i2c_get_clientdata(client);
@@ -230,7 +230,7 @@ static const struct i2c_device_id migor_ts_id[] = {
 	{ "migor_ts", 0 },
 	{ }
 };
-MODULE_DEVICE_TABLE(i2c, migor_ts);
+MODULE_DEVICE_TABLE(i2c, migor_ts_id);
 
 static struct i2c_driver migor_ts_driver = {
 	.driver = {
diff --git a/drivers/input/touchscreen/of_touchscreen.c b/drivers/input/touchscreen/of_touchscreen.c
index bb6f2fe14..8d7f9c8f2 100644
--- a/drivers/input/touchscreen/of_touchscreen.c
+++ b/drivers/input/touchscreen/of_touchscreen.c
@@ -55,12 +55,16 @@ static void touchscreen_set_params(struct input_dev *dev,
  * @input: input device that should be parsed
  * @multitouch: specifies whether parsed properties should be applied to
  *	single-touch or multi-touch axes
+ * @prop: pointer to a struct touchscreen_properties into which to store
+ *	axis swap and invert info for use with touchscreen_report_x_y();
+ *	or %NULL
  *
  * This function parses common DT properties for touchscreens and setups the
  * input device accordingly. The function keeps previously set up default
  * values if no value is specified via DT.
  */
-void touchscreen_parse_properties(struct input_dev *input, bool multitouch)
+void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
+				  struct touchscreen_properties *prop)
 {
 	struct device *dev = input->dev.parent;
 	unsigned int axis;
@@ -104,5 +108,80 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch)
 						&fuzz);
 	if (data_present)
 		touchscreen_set_params(input, axis, maximum, fuzz);
+
+	if (!prop)
+		return;
+
+	axis = multitouch ? ABS_MT_POSITION_X : ABS_X;
+
+	prop->max_x = input_abs_get_max(input, axis);
+	prop->max_y = input_abs_get_max(input, axis + 1);
+	prop->invert_x =
+		device_property_read_bool(dev, "touchscreen-inverted-x");
+	prop->invert_y =
+		device_property_read_bool(dev, "touchscreen-inverted-y");
+	prop->swap_x_y =
+		device_property_read_bool(dev, "touchscreen-swapped-x-y");
+
+	if (prop->swap_x_y)
+		swap(input->absinfo[axis], input->absinfo[axis + 1]);
 }
 EXPORT_SYMBOL(touchscreen_parse_properties);
+
+static void
+touchscreen_apply_prop_to_x_y(const struct touchscreen_properties *prop,
+			      unsigned int *x, unsigned int *y)
+{
+	if (prop->invert_x)
+		*x = prop->max_x - *x;
+
+	if (prop->invert_y)
+		*y = prop->max_y - *y;
+
+	if (prop->swap_x_y)
+		swap(*x, *y);
+}
+
+/**
+ * touchscreen_set_mt_pos - Set input_mt_pos coordinates
+ * @pos: input_mt_pos to set coordinates of
+ * @prop: pointer to a struct touchscreen_properties
+ * @x: X coordinate to store in pos
+ * @y: Y coordinate to store in pos
+ *
+ * Adjust the passed in x and y values applying any axis inversion and
+ * swapping requested in the passed in touchscreen_properties and store
+ * the result in a struct input_mt_pos.
+ */
+void touchscreen_set_mt_pos(struct input_mt_pos *pos,
+			    const struct touchscreen_properties *prop,
+			    unsigned int x, unsigned int y)
+{
+	touchscreen_apply_prop_to_x_y(prop, &x, &y);
+	pos->x = x;
+	pos->y = y;
+}
+EXPORT_SYMBOL(touchscreen_set_mt_pos);
+
+/**
+ * touchscreen_report_pos - Report touchscreen coordinates
+ * @input: input_device to report coordinates for
+ * @prop: pointer to a struct touchscreen_properties
+ * @x: X coordinate to report
+ * @y: Y coordinate to report
+ * @multitouch: Report coordinates on single-touch or multi-touch axes
+ *
+ * Adjust the passed in x and y values applying any axis inversion and
+ * swapping requested in the passed in touchscreen_properties and then
+ * report the resulting coordinates on the input_dev's x and y axis.
+ */
+void touchscreen_report_pos(struct input_dev *input,
+			    const struct touchscreen_properties *prop,
+			    unsigned int x, unsigned int y,
+			    bool multitouch)
+{
+	touchscreen_apply_prop_to_x_y(prop, &x, &y);
+	input_report_abs(input, multitouch ? ABS_MT_POSITION_X : ABS_X, x);
+	input_report_abs(input, multitouch ? ABS_MT_POSITION_Y : ABS_Y, y);
+}
+EXPORT_SYMBOL(touchscreen_report_pos);
diff --git a/drivers/input/touchscreen/pixcir_i2c_ts.c b/drivers/input/touchscreen/pixcir_i2c_ts.c
index 09523a3d3..d159e14f4 100644
--- a/drivers/input/touchscreen/pixcir_i2c_ts.c
+++ b/drivers/input/touchscreen/pixcir_i2c_ts.c
@@ -27,9 +27,9 @@
 #include <linux/input/touchscreen.h>
 #include <linux/gpio.h>
 #include <linux/gpio/consumer.h>
-/*#include <linux/of.h>*/
 #include <linux/of_device.h>
 #include <linux/platform_data/pixcir_i2c_ts.h>
+#include <asm/unaligned.h>
 
 #define PIXCIR_MAX_SLOTS       5 /* Max fingers supported by driver */
 
@@ -41,19 +41,15 @@ struct pixcir_i2c_ts_data {
 	struct gpio_desc *gpio_enable;
 	struct gpio_desc *gpio_wake;
 	const struct pixcir_i2c_chip_data *chip;
+	struct touchscreen_properties prop;
 	int max_fingers;	/* Max fingers supported in this instance */
 	bool running;
 };
 
-struct pixcir_touch {
-	int x;
-	int y;
-	int id;
-};
-
 struct pixcir_report_data {
 	int num_touches;
-	struct pixcir_touch touches[PIXCIR_MAX_SLOTS];
+	struct input_mt_pos pos[PIXCIR_MAX_SLOTS];
+	int ids[PIXCIR_MAX_SLOTS];
 };
 
 static void pixcir_ts_parse(struct pixcir_i2c_ts_data *tsdata,
@@ -98,11 +94,11 @@ static void pixcir_ts_parse(struct pixcir_i2c_ts_data *tsdata,
 	bufptr = &rdbuf[2];
 
 	for (i = 0; i < touch; i++) {
-		report->touches[i].x = (bufptr[1] << 8) | bufptr[0];
-		report->touches[i].y = (bufptr[3] << 8) | bufptr[2];
-
+		touchscreen_set_mt_pos(&report->pos[i], &tsdata->prop,
+				       get_unaligned_le16(bufptr),
+				       get_unaligned_le16(bufptr + 2));
 		if (chip->has_hw_ids) {
-			report->touches[i].id = bufptr[4];
+			report->ids[i] = bufptr[4];
 			bufptr = bufptr + 5;
 		} else {
 			bufptr = bufptr + 4;
@@ -113,9 +109,7 @@ static void pixcir_ts_parse(struct pixcir_i2c_ts_data *tsdata,
 static void pixcir_ts_report(struct pixcir_i2c_ts_data *ts,
 			     struct pixcir_report_data *report)
 {
-	struct input_mt_pos pos[PIXCIR_MAX_SLOTS];
 	int slots[PIXCIR_MAX_SLOTS];
-	struct pixcir_touch *touch;
 	int n, i, slot;
 	struct device *dev = &ts->client->dev;
 	const struct pixcir_i2c_chip_data *chip = ts->chip;
@@ -124,24 +118,16 @@ static void pixcir_ts_report(struct pixcir_i2c_ts_data *ts,
 	if (n > PIXCIR_MAX_SLOTS)
 		n = PIXCIR_MAX_SLOTS;
 
-	if (!ts->chip->has_hw_ids) {
-		for (i = 0; i < n; i++) {
-			touch = &report->touches[i];
-			pos[i].x = touch->x;
-			pos[i].y = touch->y;
-		}
-
-		input_mt_assign_slots(ts->input, slots, pos, n, 0);
-	}
+	if (!ts->chip->has_hw_ids)
+		input_mt_assign_slots(ts->input, slots, report->pos, n, 0);
 
 	for (i = 0; i < n; i++) {
-		touch = &report->touches[i];
-
 		if (chip->has_hw_ids) {
-			slot = input_mt_get_slot_by_key(ts->input, touch->id);
+			slot = input_mt_get_slot_by_key(ts->input,
+							report->ids[i]);
 			if (slot < 0) {
 				dev_dbg(dev, "no free slot for id 0x%x\n",
-					touch->id);
+					report->ids[i]);
 				continue;
 			}
 		} else {
@@ -149,14 +135,15 @@ static void pixcir_ts_report(struct pixcir_i2c_ts_data *ts,
 		}
 
 		input_mt_slot(ts->input, slot);
-		input_mt_report_slot_state(ts->input,
-					   MT_TOOL_FINGER, true);
+		input_mt_report_slot_state(ts->input, MT_TOOL_FINGER, true);
 
-		input_event(ts->input, EV_ABS, ABS_MT_POSITION_X, touch->x);
-		input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y, touch->y);
+		input_report_abs(ts->input, ABS_MT_POSITION_X,
+				 report->pos[i].x);
+		input_report_abs(ts->input, ABS_MT_POSITION_Y,
+				 report->pos[i].y);
 
 		dev_dbg(dev, "%d: slot %d, x %d, y %d\n",
-			i, slot, touch->x, touch->y);
+			i, slot, report->pos[i].x, report->pos[i].y);
 	}
 
 	input_mt_sync_frame(ts->input);
@@ -515,7 +502,7 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 	} else {
 		input_set_capability(input, EV_ABS, ABS_MT_POSITION_X);
 		input_set_capability(input, EV_ABS, ABS_MT_POSITION_Y);
-		touchscreen_parse_properties(input, true);
+		touchscreen_parse_properties(input, true, &tsdata->prop);
 		if (!input_abs_get_max(input, ABS_MT_POSITION_X) ||
 		    !input_abs_get_max(input, ABS_MT_POSITION_Y)) {
 			dev_err(dev, "Touchscreen size is not specified\n");
diff --git a/drivers/input/touchscreen/raydium_i2c_ts.c b/drivers/input/touchscreen/raydium_i2c_ts.c
new file mode 100644
index 000000000..99f4df287
--- /dev/null
+++ b/drivers/input/touchscreen/raydium_i2c_ts.c
@@ -0,0 +1,1238 @@
+/*
+ * Raydium touchscreen I2C driver.
+ *
+ * Copyright (C) 2012-2014, Raydium Semiconductor Corporation.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2, and only version 2, as published by the
+ * Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * Raydium reserves the right to make changes without further notice
+ * to the materials described herein. Raydium does not assume any
+ * liability arising out of the application described herein.
+ *
+ * Contact Raydium Semiconductor Corporation at www.rad-ic.com
+ */
+
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <asm/unaligned.h>
+
+/* Slave I2C mode */
+#define RM_BOOT_BLDR		0x02
+#define RM_BOOT_MAIN		0x03
+
+/* I2C bootoloader commands */
+#define RM_CMD_BOOT_PAGE_WRT	0x0B		/* send bl page write */
+#define RM_CMD_BOOT_WRT		0x11		/* send bl write */
+#define RM_CMD_BOOT_ACK		0x22		/* send ack*/
+#define RM_CMD_BOOT_CHK		0x33		/* send data check */
+#define RM_CMD_BOOT_READ	0x44		/* send wait bl data ready*/
+
+#define RM_BOOT_RDY		0xFF		/* bl data ready */
+
+/* I2C main commands */
+#define RM_CMD_QUERY_BANK	0x2B
+#define RM_CMD_DATA_BANK	0x4D
+#define RM_CMD_ENTER_SLEEP	0x4E
+#define RM_CMD_BANK_SWITCH	0xAA
+
+#define RM_RESET_MSG_ADDR	0x40000004
+
+#define RM_MAX_READ_SIZE	56
+#define RM_PACKET_CRC_SIZE	2
+
+/* Touch relative info */
+#define RM_MAX_RETRIES		3
+#define RM_MAX_TOUCH_NUM	10
+#define RM_BOOT_DELAY_MS	100
+
+/* Offsets in contact data */
+#define RM_CONTACT_STATE_POS	0
+#define RM_CONTACT_X_POS	1
+#define RM_CONTACT_Y_POS	3
+#define RM_CONTACT_PRESSURE_POS	5
+#define RM_CONTACT_WIDTH_X_POS	6
+#define RM_CONTACT_WIDTH_Y_POS	7
+
+/* Bootloader relative info */
+#define RM_BL_WRT_CMD_SIZE	3	/* bl flash wrt cmd size */
+#define RM_BL_WRT_PKG_SIZE	32	/* bl wrt pkg size */
+#define RM_BL_WRT_LEN		(RM_BL_WRT_PKG_SIZE + RM_BL_WRT_CMD_SIZE)
+#define RM_FW_PAGE_SIZE		128
+#define RM_MAX_FW_RETRIES	30
+#define RM_MAX_FW_SIZE		0xD000
+
+#define RM_POWERON_DELAY_USEC	500
+#define RM_RESET_DELAY_MSEC	50
+
+enum raydium_bl_cmd {
+	BL_HEADER = 0,
+	BL_PAGE_STR,
+	BL_PKG_IDX,
+	BL_DATA_STR,
+};
+
+enum raydium_bl_ack {
+	RAYDIUM_ACK_NULL = 0,
+	RAYDIUM_WAIT_READY,
+	RAYDIUM_PATH_READY,
+};
+
+enum raydium_boot_mode {
+	RAYDIUM_TS_MAIN = 0,
+	RAYDIUM_TS_BLDR,
+};
+
+/* Response to RM_CMD_DATA_BANK request */
+struct raydium_data_info {
+	__le32 data_bank_addr;
+	u8 pkg_size;
+	u8 tp_info_size;
+};
+
+struct raydium_info {
+	__le32 hw_ver;		/*device version */
+	u8 main_ver;
+	u8 sub_ver;
+	__le16 ft_ver;		/* test version */
+	u8 x_num;
+	u8 y_num;
+	__le16 x_max;
+	__le16 y_max;
+	u8 x_res;		/* units/mm */
+	u8 y_res;		/* units/mm */
+};
+
+/* struct raydium_data - represents state of Raydium touchscreen device */
+struct raydium_data {
+	struct i2c_client *client;
+	struct input_dev *input;
+
+	struct regulator *avdd;
+	struct regulator *vccio;
+	struct gpio_desc *reset_gpio;
+
+	struct raydium_info info;
+
+	struct mutex sysfs_mutex;
+
+	u8 *report_data;
+
+	u32 data_bank_addr;
+	u8 report_size;
+	u8 contact_size;
+	u8 pkg_size;
+
+	enum raydium_boot_mode boot_mode;
+
+	bool wake_irq_enabled;
+};
+
+static int raydium_i2c_send(struct i2c_client *client,
+			    u8 addr, const void *data, size_t len)
+{
+	u8 *buf;
+	int tries = 0;
+	int ret;
+
+	buf = kmalloc(len + 1, GFP_KERNEL);
+	if (!buf)
+		return -ENOMEM;
+
+	buf[0] = addr;
+	memcpy(buf + 1, data, len);
+
+	do {
+		ret = i2c_master_send(client, buf, len + 1);
+		if (likely(ret == len + 1))
+			break;
+
+		msleep(20);
+	} while (++tries < RM_MAX_RETRIES);
+
+	kfree(buf);
+
+	if (unlikely(ret != len + 1)) {
+		if (ret >= 0)
+			ret = -EIO;
+		dev_err(&client->dev, "%s failed: %d\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int raydium_i2c_read(struct i2c_client *client,
+			    u8 addr, void *data, size_t len)
+{
+	struct i2c_msg xfer[] = {
+		{
+			.addr = client->addr,
+			.len = 1,
+			.buf = &addr,
+		},
+		{
+			.addr = client->addr,
+			.flags = I2C_M_RD,
+			.len = len,
+			.buf = data,
+		}
+	};
+	int ret;
+
+	ret = i2c_transfer(client->adapter, xfer, ARRAY_SIZE(xfer));
+	if (unlikely(ret != ARRAY_SIZE(xfer)))
+		return ret < 0 ? ret : -EIO;
+
+	return 0;
+}
+
+static int raydium_i2c_read_message(struct i2c_client *client,
+				    u32 addr, void *data, size_t len)
+{
+	__be32 be_addr;
+	size_t xfer_len;
+	int error;
+
+	while (len) {
+		xfer_len = min_t(size_t, len, RM_MAX_READ_SIZE);
+
+		be_addr = cpu_to_be32(addr);
+
+		error = raydium_i2c_send(client, RM_CMD_BANK_SWITCH,
+					 &be_addr, sizeof(be_addr));
+		if (!error)
+			error = raydium_i2c_read(client, addr & 0xff,
+						 data, xfer_len);
+		if (error)
+			return error;
+
+		len -= xfer_len;
+		data += xfer_len;
+		addr += xfer_len;
+	}
+
+	return 0;
+}
+
+static int raydium_i2c_send_message(struct i2c_client *client,
+				    u32 addr, const void *data, size_t len)
+{
+	__be32 be_addr = cpu_to_be32(addr);
+	int error;
+
+	error = raydium_i2c_send(client, RM_CMD_BANK_SWITCH,
+				 &be_addr, sizeof(be_addr));
+	if (!error)
+		error = raydium_i2c_send(client, addr & 0xff, data, len);
+
+	return error;
+}
+
+static int raydium_i2c_sw_reset(struct i2c_client *client)
+{
+	const u8 soft_rst_cmd = 0x01;
+	int error;
+
+	error = raydium_i2c_send_message(client, RM_RESET_MSG_ADDR,
+					 &soft_rst_cmd, sizeof(soft_rst_cmd));
+	if (error) {
+		dev_err(&client->dev, "software reset failed: %d\n", error);
+		return error;
+	}
+
+	msleep(RM_RESET_DELAY_MSEC);
+
+	return 0;
+}
+
+static int raydium_i2c_query_ts_info(struct raydium_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	struct raydium_data_info data_info;
+	__le32 query_bank_addr;
+
+	int error, retry_cnt;
+
+	for (retry_cnt = 0; retry_cnt < RM_MAX_RETRIES; retry_cnt++) {
+		error = raydium_i2c_read(client, RM_CMD_DATA_BANK,
+					 &data_info, sizeof(data_info));
+		if (error)
+			continue;
+
+		/*
+		 * Warn user if we already allocated memory for reports and
+		 * then the size changed (due to firmware update?) and keep
+		 * old size instead.
+		 */
+		if (ts->report_data && ts->pkg_size != data_info.pkg_size) {
+			dev_warn(&client->dev,
+				 "report size changes, was: %d, new: %d\n",
+				 ts->pkg_size, data_info.pkg_size);
+		} else {
+			ts->pkg_size = data_info.pkg_size;
+			ts->report_size = ts->pkg_size - RM_PACKET_CRC_SIZE;
+		}
+
+		ts->contact_size = data_info.tp_info_size;
+		ts->data_bank_addr = le32_to_cpu(data_info.data_bank_addr);
+
+		dev_dbg(&client->dev,
+			"data_bank_addr: %#08x, report_size: %d, contact_size: %d\n",
+			ts->data_bank_addr, ts->report_size, ts->contact_size);
+
+		error = raydium_i2c_read(client, RM_CMD_QUERY_BANK,
+					 &query_bank_addr,
+					 sizeof(query_bank_addr));
+		if (error)
+			continue;
+
+		error = raydium_i2c_read_message(client,
+						 le32_to_cpu(query_bank_addr),
+						 &ts->info, sizeof(ts->info));
+		if (error)
+			continue;
+
+		return 0;
+	}
+
+	dev_err(&client->dev, "failed to query device parameters: %d\n", error);
+	return error;
+}
+
+static int raydium_i2c_check_fw_status(struct raydium_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	static const u8 bl_ack = 0x62;
+	static const u8 main_ack = 0x66;
+	u8 buf[4];
+	int error;
+
+	error = raydium_i2c_read(client, RM_CMD_BOOT_READ, buf, sizeof(buf));
+	if (!error) {
+		if (buf[0] == bl_ack)
+			ts->boot_mode = RAYDIUM_TS_BLDR;
+		else if (buf[0] == main_ack)
+			ts->boot_mode = RAYDIUM_TS_MAIN;
+		return 0;
+	}
+
+	return error;
+}
+
+static int raydium_i2c_initialize(struct raydium_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	int error, retry_cnt;
+
+	for (retry_cnt = 0; retry_cnt < RM_MAX_RETRIES; retry_cnt++) {
+		/* Wait for Hello packet */
+		msleep(RM_BOOT_DELAY_MS);
+
+		error = raydium_i2c_check_fw_status(ts);
+		if (error) {
+			dev_err(&client->dev,
+				"failed to read 'hello' packet: %d\n", error);
+			continue;
+		}
+
+		if (ts->boot_mode == RAYDIUM_TS_BLDR ||
+		    ts->boot_mode == RAYDIUM_TS_MAIN) {
+			break;
+		}
+	}
+
+	if (error)
+		ts->boot_mode = RAYDIUM_TS_BLDR;
+
+	if (ts->boot_mode == RAYDIUM_TS_BLDR) {
+		ts->info.hw_ver = cpu_to_le32(0xffffffffUL);
+		ts->info.main_ver = 0xff;
+		ts->info.sub_ver = 0xff;
+	} else {
+		raydium_i2c_query_ts_info(ts);
+	}
+
+	return error;
+}
+
+static int raydium_i2c_bl_chk_state(struct i2c_client *client,
+				    enum raydium_bl_ack state)
+{
+	static const u8 ack_ok[] = { 0xFF, 0x39, 0x30, 0x30, 0x54 };
+	u8 rbuf[sizeof(ack_ok)];
+	u8 retry;
+	int error;
+
+	for (retry = 0; retry < RM_MAX_FW_RETRIES; retry++) {
+		switch (state) {
+		case RAYDIUM_ACK_NULL:
+			return 0;
+
+		case RAYDIUM_WAIT_READY:
+			error = raydium_i2c_read(client, RM_CMD_BOOT_CHK,
+						 &rbuf[0], 1);
+			if (!error && rbuf[0] == RM_BOOT_RDY)
+				return 0;
+
+			break;
+
+		case RAYDIUM_PATH_READY:
+			error = raydium_i2c_read(client, RM_CMD_BOOT_CHK,
+						 rbuf, sizeof(rbuf));
+			if (!error && !memcmp(rbuf, ack_ok, sizeof(ack_ok)))
+				return 0;
+
+			break;
+
+		default:
+			dev_err(&client->dev, "%s: invalid target state %d\n",
+				__func__, state);
+			return -EINVAL;
+		}
+
+		msleep(20);
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int raydium_i2c_write_object(struct i2c_client *client,
+				    const void *data, size_t len,
+				    enum raydium_bl_ack state)
+{
+	int error;
+
+	error = raydium_i2c_send(client, RM_CMD_BOOT_WRT, data, len);
+	if (error) {
+		dev_err(&client->dev, "WRT obj command failed: %d\n",
+			error);
+		return error;
+	}
+
+	error = raydium_i2c_send(client, RM_CMD_BOOT_ACK, NULL, 0);
+	if (error) {
+		dev_err(&client->dev, "Ack obj command failed: %d\n", error);
+		return error;
+	}
+
+	error = raydium_i2c_bl_chk_state(client, state);
+	if (error) {
+		dev_err(&client->dev, "BL check state failed: %d\n", error);
+		return error;
+	}
+	return 0;
+}
+
+static bool raydium_i2c_boot_trigger(struct i2c_client *client)
+{
+	static const u8 cmd[7][6] = {
+		{ 0x08, 0x0C, 0x09, 0x00, 0x50, 0xD7 },
+		{ 0x08, 0x04, 0x09, 0x00, 0x50, 0xA5 },
+		{ 0x08, 0x04, 0x09, 0x00, 0x50, 0x00 },
+		{ 0x08, 0x04, 0x09, 0x00, 0x50, 0xA5 },
+		{ 0x08, 0x0C, 0x09, 0x00, 0x50, 0x00 },
+		{ 0x06, 0x01, 0x00, 0x00, 0x00, 0x00 },
+		{ 0x02, 0xA2, 0x00, 0x00, 0x00, 0x00 },
+	};
+	int i;
+	int error;
+
+	for (i = 0; i < 7; i++) {
+		error = raydium_i2c_write_object(client, cmd[i], sizeof(cmd[i]),
+						 RAYDIUM_WAIT_READY);
+		if (error) {
+			dev_err(&client->dev,
+				"boot trigger failed at step %d: %d\n",
+				i, error);
+			return error;
+		}
+	}
+
+	return 0;
+}
+
+static bool raydium_i2c_fw_trigger(struct i2c_client *client)
+{
+	static const u8 cmd[5][11] = {
+		{ 0, 0x09, 0x71, 0x0C, 0x09, 0x00, 0x50, 0xD7, 0, 0, 0 },
+		{ 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0xA5, 0, 0, 0 },
+		{ 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0x00, 0, 0, 0 },
+		{ 0, 0x09, 0x71, 0x04, 0x09, 0x00, 0x50, 0xA5, 0, 0, 0 },
+		{ 0, 0x09, 0x71, 0x0C, 0x09, 0x00, 0x50, 0x00, 0, 0, 0 },
+	};
+	int i;
+	int error;
+
+	for (i = 0; i < 5; i++) {
+		error = raydium_i2c_write_object(client, cmd[i], sizeof(cmd[i]),
+						 RAYDIUM_ACK_NULL);
+		if (error) {
+			dev_err(&client->dev,
+				"fw trigger failed at step %d: %d\n",
+				i, error);
+			return error;
+		}
+	}
+
+	return 0;
+}
+
+static int raydium_i2c_check_path(struct i2c_client *client)
+{
+	static const u8 cmd[] = { 0x09, 0x00, 0x09, 0x00, 0x50, 0x10, 0x00 };
+	int error;
+
+	error = raydium_i2c_write_object(client, cmd, sizeof(cmd),
+					 RAYDIUM_PATH_READY);
+	if (error) {
+		dev_err(&client->dev, "check path command failed: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int raydium_i2c_enter_bl(struct i2c_client *client)
+{
+	static const u8 cal_cmd[] = { 0x00, 0x01, 0x52 };
+	int error;
+
+	error = raydium_i2c_write_object(client, cal_cmd, sizeof(cal_cmd),
+					 RAYDIUM_ACK_NULL);
+	if (error) {
+		dev_err(&client->dev, "enter bl command failed: %d\n", error);
+		return error;
+	}
+
+	msleep(RM_BOOT_DELAY_MS);
+	return 0;
+}
+
+static int raydium_i2c_leave_bl(struct i2c_client *client)
+{
+	static const u8 leave_cmd[] = { 0x05, 0x00 };
+	int error;
+
+	error = raydium_i2c_write_object(client, leave_cmd, sizeof(leave_cmd),
+					 RAYDIUM_ACK_NULL);
+	if (error) {
+		dev_err(&client->dev, "leave bl command failed: %d\n", error);
+		return error;
+	}
+
+	msleep(RM_BOOT_DELAY_MS);
+	return 0;
+}
+
+static int raydium_i2c_write_checksum(struct i2c_client *client,
+				      size_t length, u16 checksum)
+{
+	u8 checksum_cmd[] = { 0x00, 0x05, 0x6D, 0x00, 0x00, 0x00, 0x00 };
+	int error;
+
+	put_unaligned_le16(length, &checksum_cmd[3]);
+	put_unaligned_le16(checksum, &checksum_cmd[5]);
+
+	error = raydium_i2c_write_object(client,
+					 checksum_cmd, sizeof(checksum_cmd),
+					 RAYDIUM_ACK_NULL);
+	if (error) {
+		dev_err(&client->dev, "failed to write checksum: %d\n",
+			error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int raydium_i2c_disable_watch_dog(struct i2c_client *client)
+{
+	static const u8 cmd[] = { 0x0A, 0xAA };
+	int error;
+
+	error = raydium_i2c_write_object(client, cmd, sizeof(cmd),
+					 RAYDIUM_WAIT_READY);
+	if (error) {
+		dev_err(&client->dev, "disable watchdog command failed: %d\n",
+			error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int raydium_i2c_fw_write_page(struct i2c_client *client,
+				     u16 page_idx, const void *data, size_t len)
+{
+	u8 buf[RM_BL_WRT_LEN];
+	size_t xfer_len;
+	int error;
+	int i;
+
+	BUILD_BUG_ON((RM_FW_PAGE_SIZE % RM_BL_WRT_PKG_SIZE) != 0);
+
+	for (i = 0; i < RM_FW_PAGE_SIZE / RM_BL_WRT_PKG_SIZE; i++) {
+		buf[BL_HEADER] = RM_CMD_BOOT_PAGE_WRT;
+		buf[BL_PAGE_STR] = page_idx ? 0xff : 0;
+		buf[BL_PKG_IDX] = i + 1;
+
+		xfer_len = min_t(size_t, len, RM_BL_WRT_PKG_SIZE);
+		memcpy(&buf[BL_DATA_STR], data, xfer_len);
+		if (len < RM_BL_WRT_PKG_SIZE)
+			memset(&buf[BL_DATA_STR + xfer_len], 0xff,
+				RM_BL_WRT_PKG_SIZE - xfer_len);
+
+		error = raydium_i2c_write_object(client, buf, RM_BL_WRT_LEN,
+						 RAYDIUM_WAIT_READY);
+		if (error) {
+			dev_err(&client->dev,
+				"page write command failed for page %d, chunk %d: %d\n",
+				page_idx, i, error);
+			return error;
+		}
+
+		data += xfer_len;
+		len -= xfer_len;
+	}
+
+	return error;
+}
+
+static u16 raydium_calc_chksum(const u8 *buf, u16 len)
+{
+	u16 checksum = 0;
+	u16 i;
+
+	for (i = 0; i < len; i++)
+		checksum += buf[i];
+
+	return checksum;
+}
+
+static int raydium_i2c_do_update_firmware(struct raydium_data *ts,
+					 const struct firmware *fw)
+{
+	struct i2c_client *client = ts->client;
+	const void *data;
+	size_t data_len;
+	size_t len;
+	int page_nr;
+	int i;
+	int error;
+	u16 fw_checksum;
+
+	if (fw->size == 0 || fw->size > RM_MAX_FW_SIZE) {
+		dev_err(&client->dev, "Invalid firmware length\n");
+		return -EINVAL;
+	}
+
+	error = raydium_i2c_check_fw_status(ts);
+	if (error) {
+		dev_err(&client->dev, "Unable to access IC %d\n", error);
+		return error;
+	}
+
+	if (ts->boot_mode == RAYDIUM_TS_MAIN) {
+		for (i = 0; i < RM_MAX_RETRIES; i++) {
+			error = raydium_i2c_enter_bl(client);
+			if (!error) {
+				error = raydium_i2c_check_fw_status(ts);
+				if (error) {
+					dev_err(&client->dev,
+						"unable to access IC: %d\n",
+						error);
+					return error;
+				}
+
+				if (ts->boot_mode == RAYDIUM_TS_BLDR)
+					break;
+			}
+		}
+
+		if (ts->boot_mode == RAYDIUM_TS_MAIN) {
+			dev_err(&client->dev,
+				"failied to jump to boot loader: %d\n",
+				error);
+			return -EIO;
+		}
+	}
+
+	error = raydium_i2c_disable_watch_dog(client);
+	if (error)
+		return error;
+
+	error = raydium_i2c_check_path(client);
+	if (error)
+		return error;
+
+	error = raydium_i2c_boot_trigger(client);
+	if (error) {
+		dev_err(&client->dev, "send boot trigger fail: %d\n", error);
+		return error;
+	}
+
+	msleep(RM_BOOT_DELAY_MS);
+
+	data = fw->data;
+	data_len = fw->size;
+	page_nr = 0;
+
+	while (data_len) {
+		len = min_t(size_t, data_len, RM_FW_PAGE_SIZE);
+
+		error = raydium_i2c_fw_write_page(client, page_nr++, data, len);
+		if (error)
+			return error;
+
+		msleep(20);
+
+		data += len;
+		data_len -= len;
+	}
+
+	error = raydium_i2c_leave_bl(client);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to leave boot loader: %d\n", error);
+		return error;
+	}
+
+	dev_dbg(&client->dev, "left boot loader mode\n");
+	msleep(RM_BOOT_DELAY_MS);
+
+	error = raydium_i2c_check_fw_status(ts);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to check fw status after write: %d\n",
+			error);
+		return error;
+	}
+
+	if (ts->boot_mode != RAYDIUM_TS_MAIN) {
+		dev_err(&client->dev,
+			"failed to switch to main fw after writing firmware: %d\n",
+			error);
+		return -EINVAL;
+	}
+
+	error = raydium_i2c_fw_trigger(client);
+	if (error) {
+		dev_err(&client->dev, "failed to trigger fw: %d\n", error);
+		return error;
+	}
+
+	fw_checksum = raydium_calc_chksum(fw->data, fw->size);
+
+	error = raydium_i2c_write_checksum(client, fw->size, fw_checksum);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+static int raydium_i2c_fw_update(struct raydium_data *ts)
+{
+	struct i2c_client *client = ts->client;
+	const struct firmware *fw = NULL;
+	const char *fw_file = "/*(DEBLOBBED)*/";
+	int error;
+
+	error = reject_firmware(&fw, fw_file, &client->dev);
+	if (error) {
+		dev_err(&client->dev, "Unable to open firmware %s\n", fw_file);
+		return error;
+	}
+
+	disable_irq(client->irq);
+
+	error = raydium_i2c_do_update_firmware(ts, fw);
+	if (error) {
+		dev_err(&client->dev, "firmware update failed: %d\n", error);
+		ts->boot_mode = RAYDIUM_TS_BLDR;
+		goto out_enable_irq;
+	}
+
+	error = raydium_i2c_initialize(ts);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to initialize device after firmware update: %d\n",
+			error);
+		ts->boot_mode = RAYDIUM_TS_BLDR;
+		goto out_enable_irq;
+	}
+
+	ts->boot_mode = RAYDIUM_TS_MAIN;
+
+out_enable_irq:
+	enable_irq(client->irq);
+	msleep(100);
+
+	release_firmware(fw);
+
+	return error;
+}
+
+static void raydium_mt_event(struct raydium_data *ts)
+{
+	int i;
+
+	for (i = 0; i < ts->report_size / ts->contact_size; i++) {
+		u8 *contact = &ts->report_data[ts->contact_size * i];
+		bool state = contact[RM_CONTACT_STATE_POS];
+		u8 wx, wy;
+
+		input_mt_slot(ts->input, i);
+		input_mt_report_slot_state(ts->input, MT_TOOL_FINGER, state);
+
+		if (!state)
+			continue;
+
+		input_report_abs(ts->input, ABS_MT_POSITION_X,
+				get_unaligned_le16(&contact[RM_CONTACT_X_POS]));
+		input_report_abs(ts->input, ABS_MT_POSITION_Y,
+				get_unaligned_le16(&contact[RM_CONTACT_Y_POS]));
+		input_report_abs(ts->input, ABS_MT_PRESSURE,
+				contact[RM_CONTACT_PRESSURE_POS]);
+
+		wx = contact[RM_CONTACT_WIDTH_X_POS];
+		wy = contact[RM_CONTACT_WIDTH_Y_POS];
+
+		input_report_abs(ts->input, ABS_MT_TOUCH_MAJOR, max(wx, wy));
+		input_report_abs(ts->input, ABS_MT_TOUCH_MINOR, min(wx, wy));
+	}
+
+	input_mt_sync_frame(ts->input);
+	input_sync(ts->input);
+}
+
+static irqreturn_t raydium_i2c_irq(int irq, void *_dev)
+{
+	struct raydium_data *ts = _dev;
+	int error;
+	u16 fw_crc;
+	u16 calc_crc;
+
+	if (ts->boot_mode != RAYDIUM_TS_MAIN)
+		goto out;
+
+	error = raydium_i2c_read_message(ts->client, ts->data_bank_addr,
+					 ts->report_data, ts->pkg_size);
+	if (error)
+		goto out;
+
+	fw_crc = get_unaligned_le16(&ts->report_data[ts->report_size]);
+	calc_crc = raydium_calc_chksum(ts->report_data, ts->report_size);
+	if (unlikely(fw_crc != calc_crc)) {
+		dev_warn(&ts->client->dev,
+			 "%s: invalid packet crc %#04x vs %#04x\n",
+			 __func__, calc_crc, fw_crc);
+		goto out;
+	}
+
+	raydium_mt_event(ts);
+
+out:
+	return IRQ_HANDLED;
+}
+
+static ssize_t raydium_i2c_fw_ver_show(struct device *dev,
+				       struct device_attribute *attr, char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct raydium_data *ts = i2c_get_clientdata(client);
+
+	return sprintf(buf, "%d.%d\n", ts->info.main_ver, ts->info.sub_ver);
+}
+
+static ssize_t raydium_i2c_hw_ver_show(struct device *dev,
+				       struct device_attribute *attr, char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct raydium_data *ts = i2c_get_clientdata(client);
+
+	return sprintf(buf, "%#04x\n", le32_to_cpu(ts->info.hw_ver));
+}
+
+static ssize_t raydium_i2c_boot_mode_show(struct device *dev,
+					  struct device_attribute *attr,
+					  char *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct raydium_data *ts = i2c_get_clientdata(client);
+
+	return sprintf(buf, "%s\n",
+		       ts->boot_mode == RAYDIUM_TS_MAIN ?
+				"Normal" : "Recovery");
+}
+
+static ssize_t raydium_i2c_update_fw_store(struct device *dev,
+					   struct device_attribute *attr,
+					   const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct raydium_data *ts = i2c_get_clientdata(client);
+	int error;
+
+	error = mutex_lock_interruptible(&ts->sysfs_mutex);
+	if (error)
+		return error;
+
+	error = raydium_i2c_fw_update(ts);
+
+	mutex_unlock(&ts->sysfs_mutex);
+
+	return error ?: count;
+}
+
+static ssize_t raydium_i2c_calibrate_store(struct device *dev,
+					   struct device_attribute *attr,
+					   const char *buf, size_t count)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct raydium_data *ts = i2c_get_clientdata(client);
+	static const u8 cal_cmd[] = { 0x00, 0x01, 0x9E };
+	int error;
+
+	error = mutex_lock_interruptible(&ts->sysfs_mutex);
+	if (error)
+		return error;
+
+	error = raydium_i2c_write_object(client, cal_cmd, sizeof(cal_cmd),
+					 RAYDIUM_WAIT_READY);
+	if (error)
+		dev_err(&client->dev, "calibrate command failed: %d\n", error);
+
+	mutex_unlock(&ts->sysfs_mutex);
+	return error ?: count;
+}
+
+static DEVICE_ATTR(fw_version, S_IRUGO, raydium_i2c_fw_ver_show, NULL);
+static DEVICE_ATTR(hw_version, S_IRUGO, raydium_i2c_hw_ver_show, NULL);
+static DEVICE_ATTR(boot_mode, S_IRUGO, raydium_i2c_boot_mode_show, NULL);
+static DEVICE_ATTR(update_fw, S_IWUSR, NULL, raydium_i2c_update_fw_store);
+static DEVICE_ATTR(calibrate, S_IWUSR, NULL, raydium_i2c_calibrate_store);
+
+static struct attribute *raydium_i2c_attributes[] = {
+	&dev_attr_update_fw.attr,
+	&dev_attr_boot_mode.attr,
+	&dev_attr_fw_version.attr,
+	&dev_attr_hw_version.attr,
+	&dev_attr_calibrate.attr,
+	NULL
+};
+
+static struct attribute_group raydium_i2c_attribute_group = {
+	.attrs = raydium_i2c_attributes,
+};
+
+static void raydium_i2c_remove_sysfs_group(void *_data)
+{
+	struct raydium_data *ts = _data;
+
+	sysfs_remove_group(&ts->client->dev.kobj, &raydium_i2c_attribute_group);
+}
+
+static int raydium_i2c_power_on(struct raydium_data *ts)
+{
+	int error;
+
+	if (!ts->reset_gpio)
+		return 0;
+
+	gpiod_set_value_cansleep(ts->reset_gpio, 1);
+
+	error = regulator_enable(ts->avdd);
+	if (error) {
+		dev_err(&ts->client->dev,
+			"failed to enable avdd regulator: %d\n", error);
+		goto release_reset_gpio;
+	}
+
+	error = regulator_enable(ts->vccio);
+	if (error) {
+		regulator_disable(ts->avdd);
+		dev_err(&ts->client->dev,
+			"failed to enable vccio regulator: %d\n", error);
+		goto release_reset_gpio;
+	}
+
+	udelay(RM_POWERON_DELAY_USEC);
+
+release_reset_gpio:
+	gpiod_set_value_cansleep(ts->reset_gpio, 0);
+
+	if (error)
+		return error;
+
+	msleep(RM_RESET_DELAY_MSEC);
+
+	return 0;
+}
+
+static void raydium_i2c_power_off(void *_data)
+{
+	struct raydium_data *ts = _data;
+
+	if (ts->reset_gpio) {
+		gpiod_set_value_cansleep(ts->reset_gpio, 1);
+		regulator_disable(ts->vccio);
+		regulator_disable(ts->avdd);
+	}
+}
+
+static int raydium_i2c_probe(struct i2c_client *client,
+			     const struct i2c_device_id *id)
+{
+	union i2c_smbus_data dummy;
+	struct raydium_data *ts;
+	int error;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
+		dev_err(&client->dev,
+			"i2c check functionality error (need I2C_FUNC_I2C)\n");
+		return -ENXIO;
+	}
+
+	ts = devm_kzalloc(&client->dev, sizeof(*ts), GFP_KERNEL);
+	if (!ts)
+		return -ENOMEM;
+
+	mutex_init(&ts->sysfs_mutex);
+
+	ts->client = client;
+	i2c_set_clientdata(client, ts);
+
+	ts->avdd = devm_regulator_get(&client->dev, "avdd");
+	if (IS_ERR(ts->avdd)) {
+		error = PTR_ERR(ts->avdd);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"Failed to get 'avdd' regulator: %d\n", error);
+		return error;
+	}
+
+	ts->vccio = devm_regulator_get(&client->dev, "vccio");
+	if (IS_ERR(ts->vccio)) {
+		error = PTR_ERR(ts->vccio);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"Failed to get 'vccio' regulator: %d\n", error);
+		return error;
+	}
+
+	ts->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
+						 GPIOD_OUT_LOW);
+	if (IS_ERR(ts->reset_gpio)) {
+		error = PTR_ERR(ts->reset_gpio);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"failed to get reset gpio: %d\n", error);
+		return error;
+	}
+
+	error = raydium_i2c_power_on(ts);
+	if (error)
+		return error;
+
+	error = devm_add_action(&client->dev, raydium_i2c_power_off, ts);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to install power off action: %d\n", error);
+		raydium_i2c_power_off(ts);
+		return error;
+	}
+
+	/* Make sure there is something at this address */
+	if (i2c_smbus_xfer(client->adapter, client->addr, 0,
+			   I2C_SMBUS_READ, 0, I2C_SMBUS_BYTE, &dummy) < 0) {
+		dev_err(&client->dev, "nothing at this address\n");
+		return -ENXIO;
+	}
+
+	error = raydium_i2c_initialize(ts);
+	if (error) {
+		dev_err(&client->dev, "failed to initialize: %d\n", error);
+		return error;
+	}
+
+	ts->report_data = devm_kmalloc(&client->dev,
+				       ts->pkg_size, GFP_KERNEL);
+	if (!ts->report_data)
+		return -ENOMEM;
+
+	ts->input = devm_input_allocate_device(&client->dev);
+	if (!ts->input) {
+		dev_err(&client->dev, "Failed to allocate input device\n");
+		return -ENOMEM;
+	}
+
+	ts->input->name = "Raydium Touchscreen";
+	ts->input->id.bustype = BUS_I2C;
+
+	input_set_drvdata(ts->input, ts);
+
+	input_set_abs_params(ts->input, ABS_MT_POSITION_X,
+			     0, le16_to_cpu(ts->info.x_max), 0, 0);
+	input_set_abs_params(ts->input, ABS_MT_POSITION_Y,
+			     0, le16_to_cpu(ts->info.y_max), 0, 0);
+	input_abs_set_res(ts->input, ABS_MT_POSITION_X, ts->info.x_res);
+	input_abs_set_res(ts->input, ABS_MT_POSITION_Y, ts->info.y_res);
+
+	input_set_abs_params(ts->input, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
+	input_set_abs_params(ts->input, ABS_MT_PRESSURE, 0, 255, 0, 0);
+
+	error = input_mt_init_slots(ts->input, RM_MAX_TOUCH_NUM,
+				    INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
+	if (error) {
+		dev_err(&client->dev,
+			"failed to initialize MT slots: %d\n", error);
+		return error;
+	}
+
+	error = input_register_device(ts->input);
+	if (error) {
+		dev_err(&client->dev,
+			"unable to register input device: %d\n", error);
+		return error;
+	}
+
+	error = devm_request_threaded_irq(&client->dev, client->irq,
+					  NULL, raydium_i2c_irq,
+					  IRQF_ONESHOT, client->name, ts);
+	if (error) {
+		dev_err(&client->dev, "Failed to register interrupt\n");
+		return error;
+	}
+
+	error = sysfs_create_group(&client->dev.kobj,
+				   &raydium_i2c_attribute_group);
+	if (error) {
+		dev_err(&client->dev, "failed to create sysfs attributes: %d\n",
+			error);
+		return error;
+	}
+
+	error = devm_add_action(&client->dev,
+				raydium_i2c_remove_sysfs_group, ts);
+	if (error) {
+		raydium_i2c_remove_sysfs_group(ts);
+		dev_err(&client->dev,
+			"Failed to add sysfs cleanup action: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static void __maybe_unused raydium_enter_sleep(struct i2c_client *client)
+{
+	static const u8 sleep_cmd[] = { 0x5A, 0xff, 0x00, 0x0f };
+	int error;
+
+	error = raydium_i2c_send(client, RM_CMD_ENTER_SLEEP,
+				 sleep_cmd, sizeof(sleep_cmd));
+	if (error)
+		dev_err(&client->dev,
+			"sleep command failed: %d\n", error);
+}
+
+static int __maybe_unused raydium_i2c_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct raydium_data *ts = i2c_get_clientdata(client);
+
+	/* Sleep is not available in BLDR recovery mode */
+	if (ts->boot_mode != RAYDIUM_TS_MAIN)
+		return -EBUSY;
+
+	disable_irq(client->irq);
+
+	if (device_may_wakeup(dev)) {
+		raydium_enter_sleep(client);
+
+		ts->wake_irq_enabled = (enable_irq_wake(client->irq) == 0);
+	} else {
+		raydium_i2c_power_off(ts);
+	}
+
+	return 0;
+}
+
+static int __maybe_unused raydium_i2c_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct raydium_data *ts = i2c_get_clientdata(client);
+
+	if (device_may_wakeup(dev)) {
+		if (ts->wake_irq_enabled)
+			disable_irq_wake(client->irq);
+		raydium_i2c_sw_reset(client);
+	} else {
+		raydium_i2c_power_on(ts);
+		raydium_i2c_initialize(ts);
+	}
+
+	enable_irq(client->irq);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(raydium_i2c_pm_ops,
+			 raydium_i2c_suspend, raydium_i2c_resume);
+
+static const struct i2c_device_id raydium_i2c_id[] = {
+	{ "raydium_i2c" , 0 },
+	{ "rm32380", 0 },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, raydium_i2c_id);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id raydium_acpi_id[] = {
+	{ "RAYD0001", 0 },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(acpi, raydium_acpi_id);
+#endif
+
+#ifdef CONFIG_OF
+static const struct of_device_id raydium_of_match[] = {
+	{ .compatible = "raydium,rm32380", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, raydium_of_match);
+#endif
+
+static struct i2c_driver raydium_i2c_driver = {
+	.probe = raydium_i2c_probe,
+	.id_table = raydium_i2c_id,
+	.driver = {
+		.name = "raydium_ts",
+		.pm = &raydium_i2c_pm_ops,
+		.acpi_match_table = ACPI_PTR(raydium_acpi_id),
+		.of_match_table = of_match_ptr(raydium_of_match),
+	},
+};
+module_i2c_driver(raydium_i2c_driver);
+
+MODULE_AUTHOR("Raydium");
+MODULE_DESCRIPTION("Raydium I2c Touchscreen driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/input/touchscreen/silead.c b/drivers/input/touchscreen/silead.c
new file mode 100644
index 000000000..7b817fdc3
--- /dev/null
+++ b/drivers/input/touchscreen/silead.c
@@ -0,0 +1,566 @@
+/* -------------------------------------------------------------------------
+ * Copyright (C) 2014-2015, Intel Corporation
+ *
+ * Derived from:
+ *  gslX68X.c
+ *  Copyright (C) 2010-2015, Shanghai Sileadinc Co.Ltd
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ * -------------------------------------------------------------------------
+ */
+
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/acpi.h>
+#include <linux/interrupt.h>
+#include <linux/gpio/consumer.h>
+#include <linux/delay.h>
+#include <linux/firmware.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/input/touchscreen.h>
+#include <linux/pm.h>
+#include <linux/irq.h>
+
+#include <asm/unaligned.h>
+
+#define SILEAD_TS_NAME		"silead_ts"
+
+#define SILEAD_REG_RESET	0xE0
+#define SILEAD_REG_DATA		0x80
+#define SILEAD_REG_TOUCH_NR	0x80
+#define SILEAD_REG_POWER	0xBC
+#define SILEAD_REG_CLOCK	0xE4
+#define SILEAD_REG_STATUS	0xB0
+#define SILEAD_REG_ID		0xFC
+#define SILEAD_REG_MEM_CHECK	0xB0
+
+#define SILEAD_STATUS_OK	0x5A5A5A5A
+#define SILEAD_TS_DATA_LEN	44
+#define SILEAD_CLOCK		0x04
+
+#define SILEAD_CMD_RESET	0x88
+#define SILEAD_CMD_START	0x00
+
+#define SILEAD_POINT_DATA_LEN	0x04
+#define SILEAD_POINT_Y_OFF      0x00
+#define SILEAD_POINT_Y_MSB_OFF	0x01
+#define SILEAD_POINT_X_OFF	0x02
+#define SILEAD_POINT_X_MSB_OFF	0x03
+#define SILEAD_TOUCH_ID_MASK	0xF0
+
+#define SILEAD_CMD_SLEEP_MIN	10000
+#define SILEAD_CMD_SLEEP_MAX	20000
+#define SILEAD_POWER_SLEEP	20
+#define SILEAD_STARTUP_SLEEP	30
+
+#define SILEAD_MAX_FINGERS	10
+
+enum silead_ts_power {
+	SILEAD_POWER_ON  = 1,
+	SILEAD_POWER_OFF = 0
+};
+
+struct silead_ts_data {
+	struct i2c_client *client;
+	struct gpio_desc *gpio_power;
+	struct input_dev *input;
+	char fw_name[64];
+	struct touchscreen_properties prop;
+	u32 max_fingers;
+	u32 chip_id;
+	struct input_mt_pos pos[SILEAD_MAX_FINGERS];
+	int slots[SILEAD_MAX_FINGERS];
+	int id[SILEAD_MAX_FINGERS];
+};
+
+struct silead_fw_data {
+	u32 offset;
+	u32 val;
+};
+
+static int silead_ts_request_input_dev(struct silead_ts_data *data)
+{
+	struct device *dev = &data->client->dev;
+	int error;
+
+	data->input = devm_input_allocate_device(dev);
+	if (!data->input) {
+		dev_err(dev,
+			"Failed to allocate input device\n");
+		return -ENOMEM;
+	}
+
+	input_set_abs_params(data->input, ABS_MT_POSITION_X, 0, 4095, 0, 0);
+	input_set_abs_params(data->input, ABS_MT_POSITION_Y, 0, 4095, 0, 0);
+	touchscreen_parse_properties(data->input, true, &data->prop);
+
+	input_mt_init_slots(data->input, data->max_fingers,
+			    INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED |
+			    INPUT_MT_TRACK);
+
+	data->input->name = SILEAD_TS_NAME;
+	data->input->phys = "input/ts";
+	data->input->id.bustype = BUS_I2C;
+
+	error = input_register_device(data->input);
+	if (error) {
+		dev_err(dev, "Failed to register input device: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static void silead_ts_set_power(struct i2c_client *client,
+				enum silead_ts_power state)
+{
+	struct silead_ts_data *data = i2c_get_clientdata(client);
+
+	if (data->gpio_power) {
+		gpiod_set_value_cansleep(data->gpio_power, state);
+		msleep(SILEAD_POWER_SLEEP);
+	}
+}
+
+static void silead_ts_read_data(struct i2c_client *client)
+{
+	struct silead_ts_data *data = i2c_get_clientdata(client);
+	struct input_dev *input = data->input;
+	struct device *dev = &client->dev;
+	u8 *bufp, buf[SILEAD_TS_DATA_LEN];
+	int touch_nr, error, i;
+
+	error = i2c_smbus_read_i2c_block_data(client, SILEAD_REG_DATA,
+					      SILEAD_TS_DATA_LEN, buf);
+	if (error < 0) {
+		dev_err(dev, "Data read error %d\n", error);
+		return;
+	}
+
+	touch_nr = buf[0];
+	if (touch_nr > data->max_fingers) {
+		dev_warn(dev, "More touches reported then supported %d > %d\n",
+			 touch_nr, data->max_fingers);
+		touch_nr = data->max_fingers;
+	}
+
+	bufp = buf + SILEAD_POINT_DATA_LEN;
+	for (i = 0; i < touch_nr; i++, bufp += SILEAD_POINT_DATA_LEN) {
+		/* Bits 4-7 are the touch id */
+		data->id[i] = (bufp[SILEAD_POINT_X_MSB_OFF] &
+			       SILEAD_TOUCH_ID_MASK) >> 4;
+		touchscreen_set_mt_pos(&data->pos[i], &data->prop,
+			get_unaligned_le16(&bufp[SILEAD_POINT_X_OFF]) & 0xfff,
+			get_unaligned_le16(&bufp[SILEAD_POINT_Y_OFF]) & 0xfff);
+	}
+
+	input_mt_assign_slots(input, data->slots, data->pos, touch_nr, 0);
+
+	for (i = 0; i < touch_nr; i++) {
+		input_mt_slot(input, data->slots[i]);
+		input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
+		input_report_abs(input, ABS_MT_POSITION_X, data->pos[i].x);
+		input_report_abs(input, ABS_MT_POSITION_Y, data->pos[i].y);
+
+		dev_dbg(dev, "x=%d y=%d hw_id=%d sw_id=%d\n", data->pos[i].x,
+			data->pos[i].y, data->id[i], data->slots[i]);
+	}
+
+	input_mt_sync_frame(input);
+	input_sync(input);
+}
+
+static int silead_ts_init(struct i2c_client *client)
+{
+	struct silead_ts_data *data = i2c_get_clientdata(client);
+	int error;
+
+	error = i2c_smbus_write_byte_data(client, SILEAD_REG_RESET,
+					  SILEAD_CMD_RESET);
+	if (error)
+		goto i2c_write_err;
+	usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+	error = i2c_smbus_write_byte_data(client, SILEAD_REG_TOUCH_NR,
+					data->max_fingers);
+	if (error)
+		goto i2c_write_err;
+	usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+	error = i2c_smbus_write_byte_data(client, SILEAD_REG_CLOCK,
+					  SILEAD_CLOCK);
+	if (error)
+		goto i2c_write_err;
+	usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+	error = i2c_smbus_write_byte_data(client, SILEAD_REG_RESET,
+					  SILEAD_CMD_START);
+	if (error)
+		goto i2c_write_err;
+	usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+	return 0;
+
+i2c_write_err:
+	dev_err(&client->dev, "Registers clear error %d\n", error);
+	return error;
+}
+
+static int silead_ts_reset(struct i2c_client *client)
+{
+	int error;
+
+	error = i2c_smbus_write_byte_data(client, SILEAD_REG_RESET,
+					  SILEAD_CMD_RESET);
+	if (error)
+		goto i2c_write_err;
+	usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+	error = i2c_smbus_write_byte_data(client, SILEAD_REG_CLOCK,
+					  SILEAD_CLOCK);
+	if (error)
+		goto i2c_write_err;
+	usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+	error = i2c_smbus_write_byte_data(client, SILEAD_REG_POWER,
+					  SILEAD_CMD_START);
+	if (error)
+		goto i2c_write_err;
+	usleep_range(SILEAD_CMD_SLEEP_MIN, SILEAD_CMD_SLEEP_MAX);
+
+	return 0;
+
+i2c_write_err:
+	dev_err(&client->dev, "Chip reset error %d\n", error);
+	return error;
+}
+
+static int silead_ts_startup(struct i2c_client *client)
+{
+	int error;
+
+	error = i2c_smbus_write_byte_data(client, SILEAD_REG_RESET, 0x00);
+	if (error) {
+		dev_err(&client->dev, "Startup error %d\n", error);
+		return error;
+	}
+
+	msleep(SILEAD_STARTUP_SLEEP);
+
+	return 0;
+}
+
+static int silead_ts_load_fw(struct i2c_client *client)
+{
+	struct device *dev = &client->dev;
+	struct silead_ts_data *data = i2c_get_clientdata(client);
+	unsigned int fw_size, i;
+	const struct firmware *fw;
+	struct silead_fw_data *fw_data;
+	int error;
+
+	dev_dbg(dev, "Firmware file name: %s", data->fw_name);
+
+	error = reject_firmware(&fw, data->fw_name, dev);
+	if (error) {
+		dev_err(dev, "Firmware request error %d\n", error);
+		return error;
+	}
+
+	fw_size = fw->size / sizeof(*fw_data);
+	fw_data = (struct silead_fw_data *)fw->data;
+
+	for (i = 0; i < fw_size; i++) {
+		error = i2c_smbus_write_i2c_block_data(client,
+						       fw_data[i].offset,
+						       4,
+						       (u8 *)&fw_data[i].val);
+		if (error) {
+			dev_err(dev, "Firmware load error %d\n", error);
+			break;
+		}
+	}
+
+	release_firmware(fw);
+	return error ?: 0;
+}
+
+static u32 silead_ts_get_status(struct i2c_client *client)
+{
+	int error;
+	__le32 status;
+
+	error = i2c_smbus_read_i2c_block_data(client, SILEAD_REG_STATUS,
+					      sizeof(status), (u8 *)&status);
+	if (error < 0) {
+		dev_err(&client->dev, "Status read error %d\n", error);
+		return error;
+	}
+
+	return le32_to_cpu(status);
+}
+
+static int silead_ts_get_id(struct i2c_client *client)
+{
+	struct silead_ts_data *data = i2c_get_clientdata(client);
+	__le32 chip_id;
+	int error;
+
+	error = i2c_smbus_read_i2c_block_data(client, SILEAD_REG_ID,
+					      sizeof(chip_id), (u8 *)&chip_id);
+	if (error < 0) {
+		dev_err(&client->dev, "Chip ID read error %d\n", error);
+		return error;
+	}
+
+	data->chip_id = le32_to_cpu(chip_id);
+	dev_info(&client->dev, "Silead chip ID: 0x%8X", data->chip_id);
+
+	return 0;
+}
+
+static int silead_ts_setup(struct i2c_client *client)
+{
+	int error;
+	u32 status;
+
+	silead_ts_set_power(client, SILEAD_POWER_OFF);
+	silead_ts_set_power(client, SILEAD_POWER_ON);
+
+	error = silead_ts_get_id(client);
+	if (error)
+		return error;
+
+	error = silead_ts_init(client);
+	if (error)
+		return error;
+
+	error = silead_ts_reset(client);
+	if (error)
+		return error;
+
+	error = silead_ts_load_fw(client);
+	if (error)
+		return error;
+
+	error = silead_ts_startup(client);
+	if (error)
+		return error;
+
+	status = silead_ts_get_status(client);
+	if (status != SILEAD_STATUS_OK) {
+		dev_err(&client->dev,
+			"Initialization error, status: 0x%X\n", status);
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static irqreturn_t silead_ts_threaded_irq_handler(int irq, void *id)
+{
+	struct silead_ts_data *data = id;
+	struct i2c_client *client = data->client;
+
+	silead_ts_read_data(client);
+
+	return IRQ_HANDLED;
+}
+
+static void silead_ts_read_props(struct i2c_client *client)
+{
+	struct silead_ts_data *data = i2c_get_clientdata(client);
+	struct device *dev = &client->dev;
+	const char *str;
+	int error;
+
+	error = device_property_read_u32(dev, "silead,max-fingers",
+					 &data->max_fingers);
+	if (error) {
+		dev_dbg(dev, "Max fingers read error %d\n", error);
+		data->max_fingers = 5; /* Most devices handle up-to 5 fingers */
+	}
+
+	error = device_property_read_string(dev, "firmware-name", &str);
+	if (!error)
+		/*(DEBLOBBED)*/;
+	else
+		dev_dbg(dev, "Firmware file name read error. Using default.");
+}
+
+#ifdef CONFIG_ACPI
+static int silead_ts_set_default_fw_name(struct silead_ts_data *data,
+					 const struct i2c_device_id *id)
+{
+	const struct acpi_device_id *acpi_id;
+	struct device *dev = &data->client->dev;
+	int i;
+
+	if (ACPI_HANDLE(dev)) {
+		acpi_id = acpi_match_device(dev->driver->acpi_match_table, dev);
+		if (!acpi_id)
+			return -ENODEV;
+
+		snprintf(data->fw_name, sizeof(data->fw_name),
+			 "/*(DEBLOBBED)*/", acpi_id->id);
+
+		for (i = 0; i < strlen(data->fw_name); i++)
+			data->fw_name[i] = tolower(data->fw_name[i]);
+	} else {
+		snprintf(data->fw_name, sizeof(data->fw_name),
+			 "/*(DEBLOBBED)*/", id->name);
+	}
+
+	return 0;
+}
+#else
+static int silead_ts_set_default_fw_name(struct silead_ts_data *data,
+					 const struct i2c_device_id *id)
+{
+	snprintf(data->fw_name, sizeof(data->fw_name),
+		 "/*(DEBLOBBED)*/", id->name);
+	return 0;
+}
+#endif
+
+static int silead_ts_probe(struct i2c_client *client,
+			   const struct i2c_device_id *id)
+{
+	struct silead_ts_data *data;
+	struct device *dev = &client->dev;
+	int error;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_I2C |
+				     I2C_FUNC_SMBUS_READ_I2C_BLOCK |
+				     I2C_FUNC_SMBUS_WRITE_I2C_BLOCK)) {
+		dev_err(dev, "I2C functionality check failed\n");
+		return -ENXIO;
+	}
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	i2c_set_clientdata(client, data);
+	data->client = client;
+
+	error = silead_ts_set_default_fw_name(data, id);
+	if (error)
+		return error;
+
+	silead_ts_read_props(client);
+
+	/* We must have the IRQ provided by DT or ACPI subsytem */
+	if (client->irq <= 0)
+		return -ENODEV;
+
+	/* Power GPIO pin */
+	data->gpio_power = devm_gpiod_get_optional(dev, "power", GPIOD_OUT_LOW);
+	if (IS_ERR(data->gpio_power)) {
+		if (PTR_ERR(data->gpio_power) != -EPROBE_DEFER)
+			dev_err(dev, "Shutdown GPIO request failed\n");
+		return PTR_ERR(data->gpio_power);
+	}
+
+	error = silead_ts_setup(client);
+	if (error)
+		return error;
+
+	error = silead_ts_request_input_dev(data);
+	if (error)
+		return error;
+
+	error = devm_request_threaded_irq(dev, client->irq,
+					  NULL, silead_ts_threaded_irq_handler,
+					  IRQF_ONESHOT, client->name, data);
+	if (error) {
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "IRQ request failed %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int __maybe_unused silead_ts_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+
+	silead_ts_set_power(client, SILEAD_POWER_OFF);
+	return 0;
+}
+
+static int __maybe_unused silead_ts_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	int error, status;
+
+	silead_ts_set_power(client, SILEAD_POWER_ON);
+
+	error = silead_ts_reset(client);
+	if (error)
+		return error;
+
+	error = silead_ts_startup(client);
+	if (error)
+		return error;
+
+	status = silead_ts_get_status(client);
+	if (status != SILEAD_STATUS_OK) {
+		dev_err(dev, "Resume error, status: 0x%02x\n", status);
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(silead_ts_pm, silead_ts_suspend, silead_ts_resume);
+
+static const struct i2c_device_id silead_ts_id[] = {
+	{ "gsl1680", 0 },
+	{ "gsl1688", 0 },
+	{ "gsl3670", 0 },
+	{ "gsl3675", 0 },
+	{ "gsl3692", 0 },
+	{ "mssl1680", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, silead_ts_id);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id silead_ts_acpi_match[] = {
+	{ "GSL1680", 0 },
+	{ "GSL1688", 0 },
+	{ "GSL3670", 0 },
+	{ "GSL3675", 0 },
+	{ "GSL3692", 0 },
+	{ "MSSL1680", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, silead_ts_acpi_match);
+#endif
+
+static struct i2c_driver silead_ts_driver = {
+	.probe = silead_ts_probe,
+	.id_table = silead_ts_id,
+	.driver = {
+		.name = SILEAD_TS_NAME,
+		.acpi_match_table = ACPI_PTR(silead_ts_acpi_match),
+		.pm = &silead_ts_pm,
+	},
+};
+module_i2c_driver(silead_ts_driver);
+
+MODULE_AUTHOR("Robert Dolca <robert.dolca@intel.com>");
+MODULE_DESCRIPTION("Silead I2C touchscreen driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/input/touchscreen/sis_i2c.c b/drivers/input/touchscreen/sis_i2c.c
new file mode 100644
index 000000000..8d93f8c9a
--- /dev/null
+++ b/drivers/input/touchscreen/sis_i2c.c
@@ -0,0 +1,413 @@
+/*
+ * Touch Screen driver for SiS 9200 family I2C Touch panels
+ *
+ * Copyright (C) 2015 SiS, Inc.
+ * Copyright (C) 2016 Nextfour Group
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/crc-itu-t.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/interrupt.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <asm/unaligned.h>
+
+#define SIS_I2C_NAME		"sis_i2c_ts"
+
+/*
+ * The I2C packet format:
+ * le16		byte count
+ * u8		Report ID
+ * <contact data - variable length>
+ * u8		Number of contacts
+ * le16		Scan Time (optional)
+ * le16		CRC
+ *
+ * One touch point information consists of 6+ bytes, the order is:
+ * u8		contact state
+ * u8		finger id
+ * le16		x axis
+ * le16		y axis
+ * u8		contact width (optional)
+ * u8		contact height (optional)
+ * u8		pressure (optional)
+ *
+ * Maximum amount of data transmitted in one shot is 64 bytes, if controller
+ * needs to report more contacts than fit in one packet it will send true
+ * number of contacts in first packet and 0 as number of contacts in second
+ * packet.
+ */
+
+#define SIS_MAX_PACKET_SIZE		64
+
+#define SIS_PKT_LEN_OFFSET		0
+#define SIS_PKT_REPORT_OFFSET		2 /* Report ID/type */
+#define SIS_PKT_CONTACT_OFFSET		3 /* First contact */
+
+#define SIS_SCAN_TIME_LEN		2
+
+/* Supported report types */
+#define SIS_ALL_IN_ONE_PACKAGE		0x10
+#define SIS_PKT_IS_TOUCH(x)		(((x) & 0x0f) == 0x01)
+#define SIS_PKT_IS_HIDI2C(x)		(((x) & 0x0f) == 0x06)
+
+/* Contact properties within report */
+#define SIS_PKT_HAS_AREA(x)		((x) & BIT(4))
+#define SIS_PKT_HAS_PRESSURE(x)		((x) & BIT(5))
+#define SIS_PKT_HAS_SCANTIME(x)		((x) & BIT(6))
+
+/* Contact size */
+#define SIS_BASE_LEN_PER_CONTACT	6
+#define SIS_AREA_LEN_PER_CONTACT	2
+#define SIS_PRESSURE_LEN_PER_CONTACT	1
+
+/* Offsets within contact data */
+#define SIS_CONTACT_STATUS_OFFSET	0
+#define SIS_CONTACT_ID_OFFSET		1 /* Contact ID */
+#define SIS_CONTACT_X_OFFSET		2
+#define SIS_CONTACT_Y_OFFSET		4
+#define SIS_CONTACT_WIDTH_OFFSET	6
+#define SIS_CONTACT_HEIGHT_OFFSET	7
+#define SIS_CONTACT_PRESSURE_OFFSET(id)	(SIS_PKT_HAS_AREA(id) ? 8 : 6)
+
+/* Individual contact state */
+#define SIS_STATUS_UP			0x0
+#define SIS_STATUS_DOWN			0x3
+
+/* Touchscreen parameters */
+#define SIS_MAX_FINGERS			10
+#define SIS_MAX_X			4095
+#define SIS_MAX_Y			4095
+#define SIS_MAX_PRESSURE		255
+
+/* Resolution diagonal */
+#define SIS_AREA_LENGTH_LONGER		5792
+/*((SIS_MAX_X^2) + (SIS_MAX_Y^2))^0.5*/
+#define SIS_AREA_LENGTH_SHORT		5792
+#define SIS_AREA_UNIT			(5792 / 32)
+
+struct sis_ts_data {
+	struct i2c_client *client;
+	struct input_dev *input;
+
+	struct gpio_desc *attn_gpio;
+	struct gpio_desc *reset_gpio;
+
+	u8 packet[SIS_MAX_PACKET_SIZE];
+};
+
+static int sis_read_packet(struct i2c_client *client, u8 *buf,
+			   unsigned int *num_contacts,
+			   unsigned int *contact_size)
+{
+	int count_idx;
+	int ret;
+	u16 len;
+	u16 crc, pkg_crc;
+	u8 report_id;
+
+	ret = i2c_master_recv(client, buf, SIS_MAX_PACKET_SIZE);
+	if (ret <= 0)
+		return -EIO;
+
+	len = get_unaligned_le16(&buf[SIS_PKT_LEN_OFFSET]);
+	if (len > SIS_MAX_PACKET_SIZE) {
+		dev_err(&client->dev,
+			"%s: invalid packet length (%d vs %d)\n",
+			__func__, len, SIS_MAX_PACKET_SIZE);
+		return -E2BIG;
+	}
+
+	if (len < 10)
+		return -EINVAL;
+
+	report_id = buf[SIS_PKT_REPORT_OFFSET];
+	count_idx  = len - 1;
+	*contact_size = SIS_BASE_LEN_PER_CONTACT;
+
+	if (report_id != SIS_ALL_IN_ONE_PACKAGE) {
+		if (SIS_PKT_IS_TOUCH(report_id)) {
+			/*
+			 * Calculate CRC ignoring packet length
+			 * in the beginning and CRC transmitted
+			 * at the end of the packet.
+			 */
+			crc = crc_itu_t(0, buf + 2, len - 2 - 2);
+			pkg_crc = get_unaligned_le16(&buf[len - 2]);
+
+			if (crc != pkg_crc) {
+				dev_err(&client->dev,
+					"%s: CRC Error (%d vs %d)\n",
+					__func__, crc, pkg_crc);
+				return -EINVAL;
+			}
+
+			count_idx -= 2;
+
+		} else if (!SIS_PKT_IS_HIDI2C(report_id)) {
+			dev_err(&client->dev,
+				"%s: invalid packet ID %#02x\n",
+				__func__, report_id);
+			return -EINVAL;
+		}
+
+		if (SIS_PKT_HAS_SCANTIME(report_id))
+			count_idx -= SIS_SCAN_TIME_LEN;
+
+		if (SIS_PKT_HAS_AREA(report_id))
+			*contact_size += SIS_AREA_LEN_PER_CONTACT;
+		if (SIS_PKT_HAS_PRESSURE(report_id))
+			*contact_size += SIS_PRESSURE_LEN_PER_CONTACT;
+	}
+
+	*num_contacts = buf[count_idx];
+	return 0;
+}
+
+static int sis_ts_report_contact(struct sis_ts_data *ts, const u8 *data, u8 id)
+{
+	struct input_dev *input = ts->input;
+	int slot;
+	u8 status = data[SIS_CONTACT_STATUS_OFFSET];
+	u8 pressure;
+	u8 height, width;
+	u16 x, y;
+
+	if (status != SIS_STATUS_DOWN && status != SIS_STATUS_UP) {
+		dev_err(&ts->client->dev, "Unexpected touch status: %#02x\n",
+			data[SIS_CONTACT_STATUS_OFFSET]);
+		return -EINVAL;
+	}
+
+	slot = input_mt_get_slot_by_key(input, data[SIS_CONTACT_ID_OFFSET]);
+	if (slot < 0)
+		return -ENOENT;
+
+	input_mt_slot(input, slot);
+	input_mt_report_slot_state(input, MT_TOOL_FINGER,
+				   status == SIS_STATUS_DOWN);
+
+	if (status == SIS_STATUS_DOWN) {
+		pressure = height = width = 1;
+		if (id != SIS_ALL_IN_ONE_PACKAGE) {
+			if (SIS_PKT_HAS_AREA(id)) {
+				width = data[SIS_CONTACT_WIDTH_OFFSET];
+				height = data[SIS_CONTACT_HEIGHT_OFFSET];
+			}
+
+			if (SIS_PKT_HAS_PRESSURE(id))
+				pressure =
+					data[SIS_CONTACT_PRESSURE_OFFSET(id)];
+		}
+
+		x = get_unaligned_le16(&data[SIS_CONTACT_X_OFFSET]);
+		y = get_unaligned_le16(&data[SIS_CONTACT_Y_OFFSET]);
+
+		input_report_abs(input, ABS_MT_TOUCH_MAJOR,
+				 width * SIS_AREA_UNIT);
+		input_report_abs(input, ABS_MT_TOUCH_MINOR,
+				 height * SIS_AREA_UNIT);
+		input_report_abs(input, ABS_MT_PRESSURE, pressure);
+		input_report_abs(input, ABS_MT_POSITION_X, x);
+		input_report_abs(input, ABS_MT_POSITION_Y, y);
+	}
+
+	return 0;
+}
+
+static void sis_ts_handle_packet(struct sis_ts_data *ts)
+{
+	const u8 *contact;
+	unsigned int num_to_report = 0;
+	unsigned int num_contacts;
+	unsigned int num_reported;
+	unsigned int contact_size;
+	int error;
+	u8 report_id;
+
+	do {
+		error = sis_read_packet(ts->client, ts->packet,
+					&num_contacts, &contact_size);
+		if (error)
+			break;
+
+		if (num_to_report == 0) {
+			num_to_report = num_contacts;
+		} else if (num_contacts != 0) {
+			dev_err(&ts->client->dev,
+				"%s: nonzero (%d) point count in tail packet\n",
+				__func__, num_contacts);
+			break;
+		}
+
+		report_id = ts->packet[SIS_PKT_REPORT_OFFSET];
+		contact = &ts->packet[SIS_PKT_CONTACT_OFFSET];
+		num_reported = 0;
+
+		while (num_to_report > 0) {
+			error = sis_ts_report_contact(ts, contact, report_id);
+			if (error)
+				break;
+
+			contact += contact_size;
+			num_to_report--;
+			num_reported++;
+
+			if (report_id != SIS_ALL_IN_ONE_PACKAGE &&
+			    num_reported >= 5) {
+				/*
+				 * The remainder of contacts is sent
+				 * in the 2nd packet.
+				 */
+				break;
+			}
+		}
+	} while (num_to_report > 0);
+
+	input_mt_sync_frame(ts->input);
+	input_sync(ts->input);
+}
+
+static irqreturn_t sis_ts_irq_handler(int irq, void *dev_id)
+{
+	struct sis_ts_data *ts = dev_id;
+
+	do {
+		sis_ts_handle_packet(ts);
+	} while (ts->attn_gpio && gpiod_get_value_cansleep(ts->attn_gpio));
+
+	return IRQ_HANDLED;
+}
+
+static void sis_ts_reset(struct sis_ts_data *ts)
+{
+	if (ts->reset_gpio) {
+		/* Get out of reset */
+		usleep_range(1000, 2000);
+		gpiod_set_value(ts->reset_gpio, 1);
+		usleep_range(1000, 2000);
+		gpiod_set_value(ts->reset_gpio, 0);
+		msleep(100);
+	}
+}
+
+static int sis_ts_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct sis_ts_data *ts;
+	struct input_dev *input;
+	int error;
+
+	ts = devm_kzalloc(&client->dev, sizeof(*ts), GFP_KERNEL);
+	if (!ts)
+		return -ENOMEM;
+
+	ts->client = client;
+	i2c_set_clientdata(client, ts);
+
+	ts->attn_gpio = devm_gpiod_get_optional(&client->dev,
+						"attn", GPIOD_IN);
+	if (IS_ERR(ts->attn_gpio)) {
+		error = PTR_ERR(ts->attn_gpio);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"Failed to get attention GPIO: %d\n", error);
+		return error;
+	}
+
+	ts->reset_gpio = devm_gpiod_get_optional(&client->dev,
+						 "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ts->reset_gpio)) {
+		error = PTR_ERR(ts->reset_gpio);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"Failed to get reset GPIO: %d\n", error);
+		return error;
+	}
+
+	sis_ts_reset(ts);
+
+	ts->input = input = devm_input_allocate_device(&client->dev);
+	if (!input) {
+		dev_err(&client->dev, "Failed to allocate input device\n");
+		return -ENOMEM;
+	}
+
+	input->name = "SiS Touchscreen";
+	input->id.bustype = BUS_I2C;
+
+	input_set_abs_params(input, ABS_MT_POSITION_X, 0, SIS_MAX_X, 0, 0);
+	input_set_abs_params(input, ABS_MT_POSITION_Y, 0, SIS_MAX_Y, 0, 0);
+	input_set_abs_params(input, ABS_MT_PRESSURE, 0, SIS_MAX_PRESSURE, 0, 0);
+	input_set_abs_params(input, ABS_MT_TOUCH_MAJOR,
+			     0, SIS_AREA_LENGTH_LONGER, 0, 0);
+	input_set_abs_params(input, ABS_MT_TOUCH_MINOR,
+			     0, SIS_AREA_LENGTH_SHORT, 0, 0);
+
+	error = input_mt_init_slots(input, SIS_MAX_FINGERS, INPUT_MT_DIRECT);
+	if (error) {
+		dev_err(&client->dev,
+			"Failed to initialize MT slots: %d\n", error);
+		return error;
+	}
+
+	error = devm_request_threaded_irq(&client->dev, client->irq,
+					  NULL, sis_ts_irq_handler,
+					  IRQF_ONESHOT,
+					  client->name, ts);
+	if (error) {
+		dev_err(&client->dev, "Failed to request IRQ: %d\n", error);
+		return error;
+	}
+
+	error = input_register_device(ts->input);
+	if (error) {
+		dev_err(&client->dev,
+			"Failed to register input device: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id sis_ts_dt_ids[] = {
+	{ .compatible = "sis,9200-ts" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sis_ts_dt_ids);
+#endif
+
+static const struct i2c_device_id sis_ts_id[] = {
+	{ SIS_I2C_NAME,	0 },
+	{ "9200-ts",	0 },
+	{ /* sentinel */  }
+};
+MODULE_DEVICE_TABLE(i2c, sis_ts_id);
+
+static struct i2c_driver sis_ts_driver = {
+	.driver = {
+		.name	= SIS_I2C_NAME,
+		.of_match_table = of_match_ptr(sis_ts_dt_ids),
+	},
+	.probe		= sis_ts_probe,
+	.id_table	= sis_ts_id,
+};
+module_i2c_driver(sis_ts_driver);
+
+MODULE_DESCRIPTION("SiS 9200 Family Touchscreen Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Mika Penttilä <mika.penttila@nextfour.com>");
diff --git a/drivers/input/touchscreen/sur40.c b/drivers/input/touchscreen/sur40.c
index b7e8c11a6..4ea475775 100644
--- a/drivers/input/touchscreen/sur40.c
+++ b/drivers/input/touchscreen/sur40.c
@@ -151,7 +151,6 @@ struct sur40_state {
 	struct mutex lock;
 
 	struct vb2_queue queue;
-	struct vb2_alloc_ctx *alloc_ctx;
 	struct list_head buf_list;
 	spinlock_t qlock;
 	int sequence;
@@ -580,19 +579,13 @@ static int sur40_probe(struct usb_interface *interface,
 	sur40->queue = sur40_queue;
 	sur40->queue.drv_priv = sur40;
 	sur40->queue.lock = &sur40->lock;
+	sur40->queue.dev = sur40->dev;
 
 	/* initialize the queue */
 	error = vb2_queue_init(&sur40->queue);
 	if (error)
 		goto err_unreg_v4l2;
 
-	sur40->alloc_ctx = vb2_dma_sg_init_ctx(sur40->dev);
-	if (IS_ERR(sur40->alloc_ctx)) {
-		dev_err(sur40->dev, "Can't allocate buffer context");
-		error = PTR_ERR(sur40->alloc_ctx);
-		goto err_unreg_v4l2;
-	}
-
 	sur40->vdev = sur40_video_device;
 	sur40->vdev.v4l2_dev = &sur40->v4l2;
 	sur40->vdev.lock = &sur40->lock;
@@ -633,7 +626,6 @@ static void sur40_disconnect(struct usb_interface *interface)
 
 	video_unregister_device(&sur40->vdev);
 	v4l2_device_unregister(&sur40->v4l2);
-	vb2_dma_sg_cleanup_ctx(sur40->alloc_ctx);
 
 	input_unregister_polled_device(sur40->input);
 	input_free_polled_device(sur40->input);
@@ -653,13 +645,10 @@ static void sur40_disconnect(struct usb_interface *interface)
  */
 static int sur40_queue_setup(struct vb2_queue *q,
 		       unsigned int *nbuffers, unsigned int *nplanes,
-		       unsigned int sizes[], void *alloc_ctxs[])
+		       unsigned int sizes[], struct device *alloc_devs[])
 {
-	struct sur40_state *sur40 = vb2_get_drv_priv(q);
-
 	if (q->num_buffers + *nbuffers < 3)
 		*nbuffers = 3 - q->num_buffers;
-	alloc_ctxs[0] = sur40->alloc_ctx;
 
 	if (*nplanes)
 		return sizes[0] < sur40_video_format.sizeimage ? -EINVAL : 0;
@@ -794,7 +783,6 @@ static int sur40_vidioc_enum_fmt(struct file *file, void *priv,
 {
 	if (f->index != 0)
 		return -EINVAL;
-	strlcpy(f->description, "8-bit greyscale", sizeof(f->description));
 	f->pixelformat = V4L2_PIX_FMT_GREY;
 	f->flags = 0;
 	return 0;
diff --git a/drivers/input/touchscreen/surface3_spi.c b/drivers/input/touchscreen/surface3_spi.c
new file mode 100644
index 000000000..e12fb9b63
--- /dev/null
+++ b/drivers/input/touchscreen/surface3_spi.c
@@ -0,0 +1,427 @@
+/*
+ *  Driver for Ntrig/Microsoft Touchscreens over SPI
+ *
+ *  Copyright (c) 2016 Red Hat Inc.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; version 2 of the License.
+ */
+
+#include <linux/kernel.h>
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/acpi.h>
+
+#include <asm/unaligned.h>
+
+#define SURFACE3_PACKET_SIZE	264
+
+#define SURFACE3_REPORT_TOUCH	0xd2
+#define SURFACE3_REPORT_PEN	0x16
+
+struct surface3_ts_data {
+	struct spi_device *spi;
+	struct gpio_desc *gpiod_rst[2];
+	struct input_dev *input_dev;
+	struct input_dev *pen_input_dev;
+	int pen_tool;
+
+	u8 rd_buf[SURFACE3_PACKET_SIZE]		____cacheline_aligned;
+};
+
+struct surface3_ts_data_finger {
+	u8 status;
+	__le16 tracking_id;
+	__le16 x;
+	__le16 cx;
+	__le16 y;
+	__le16 cy;
+	__le16 width;
+	__le16 height;
+	u32 padding;
+} __packed;
+
+struct surface3_ts_data_pen {
+	u8 status;
+	__le16 x;
+	__le16 y;
+	__le16 pressure;
+	u8 padding;
+} __packed;
+
+static int surface3_spi_read(struct surface3_ts_data *ts_data)
+{
+	struct spi_device *spi = ts_data->spi;
+
+	memset(ts_data->rd_buf, 0, sizeof(ts_data->rd_buf));
+	return spi_read(spi, ts_data->rd_buf, sizeof(ts_data->rd_buf));
+}
+
+static void surface3_spi_report_touch(struct surface3_ts_data *ts_data,
+				   struct surface3_ts_data_finger *finger)
+{
+	int st = finger->status & 0x01;
+	int slot;
+
+	slot = input_mt_get_slot_by_key(ts_data->input_dev,
+				get_unaligned_le16(&finger->tracking_id));
+	if (slot < 0)
+		return;
+
+	input_mt_slot(ts_data->input_dev, slot);
+	input_mt_report_slot_state(ts_data->input_dev, MT_TOOL_FINGER, st);
+	if (st) {
+		input_report_abs(ts_data->input_dev,
+				 ABS_MT_POSITION_X,
+				 get_unaligned_le16(&finger->x));
+		input_report_abs(ts_data->input_dev,
+				 ABS_MT_POSITION_Y,
+				 get_unaligned_le16(&finger->y));
+		input_report_abs(ts_data->input_dev,
+				 ABS_MT_WIDTH_MAJOR,
+				 get_unaligned_le16(&finger->width));
+		input_report_abs(ts_data->input_dev,
+				 ABS_MT_WIDTH_MINOR,
+				 get_unaligned_le16(&finger->height));
+	}
+}
+
+static void surface3_spi_process_touch(struct surface3_ts_data *ts_data, u8 *data)
+{
+	u16 timestamp;
+	unsigned int i;
+	timestamp = get_unaligned_le16(&data[15]);
+
+	for (i = 0; i < 13; i++) {
+		struct surface3_ts_data_finger *finger;
+
+		finger = (struct surface3_ts_data_finger *)&data[17 +
+				i * sizeof(struct surface3_ts_data_finger)];
+
+		/*
+		 * When bit 5 of status is 1, it marks the end of the report:
+		 * - touch present: 0xe7
+		 * - touch released: 0xe4
+		 * - nothing valuable: 0xff
+		 */
+		if (finger->status & 0x10)
+			break;
+
+		surface3_spi_report_touch(ts_data, finger);
+	}
+
+	input_mt_sync_frame(ts_data->input_dev);
+	input_sync(ts_data->input_dev);
+}
+
+static void surface3_spi_report_pen(struct surface3_ts_data *ts_data,
+				    struct surface3_ts_data_pen *pen)
+{
+	struct input_dev *dev = ts_data->pen_input_dev;
+	int st = pen->status;
+	int prox = st & 0x01;
+	int rubber = st & 0x18;
+	int tool = (prox && rubber) ? BTN_TOOL_RUBBER : BTN_TOOL_PEN;
+
+	/* fake proximity out to switch tools */
+	if (ts_data->pen_tool != tool) {
+		input_report_key(dev, ts_data->pen_tool, 0);
+		input_sync(dev);
+		ts_data->pen_tool = tool;
+	}
+
+	input_report_key(dev, BTN_TOUCH, st & 0x12);
+
+	input_report_key(dev, ts_data->pen_tool, prox);
+
+	if (st) {
+		input_report_key(dev,
+				 BTN_STYLUS,
+				 st & 0x04);
+
+		input_report_abs(dev,
+				 ABS_X,
+				 get_unaligned_le16(&pen->x));
+		input_report_abs(dev,
+				 ABS_Y,
+				 get_unaligned_le16(&pen->y));
+		input_report_abs(dev,
+				 ABS_PRESSURE,
+				 get_unaligned_le16(&pen->pressure));
+	}
+}
+
+static void surface3_spi_process_pen(struct surface3_ts_data *ts_data, u8 *data)
+{
+	struct surface3_ts_data_pen *pen;
+
+	pen = (struct surface3_ts_data_pen *)&data[15];
+
+	surface3_spi_report_pen(ts_data, pen);
+	input_sync(ts_data->pen_input_dev);
+}
+
+static void surface3_spi_process(struct surface3_ts_data *ts_data)
+{
+	const char header[] = {
+		0xff, 0xff, 0xff, 0xff, 0xa5, 0x5a, 0xe7, 0x7e, 0x01
+	};
+	u8 *data = ts_data->rd_buf;
+
+	if (memcmp(header, data, sizeof(header)))
+		dev_err(&ts_data->spi->dev,
+			"%s header error: %*ph, ignoring...\n",
+			__func__, (int)sizeof(header), data);
+
+	switch (data[9]) {
+	case SURFACE3_REPORT_TOUCH:
+		surface3_spi_process_touch(ts_data, data);
+		break;
+	case SURFACE3_REPORT_PEN:
+		surface3_spi_process_pen(ts_data, data);
+		break;
+	default:
+		dev_err(&ts_data->spi->dev,
+			"%s unknown packet type: %x, ignoring...\n",
+			__func__, data[9]);
+		break;
+	}
+}
+
+static irqreturn_t surface3_spi_irq_handler(int irq, void *dev_id)
+{
+	struct surface3_ts_data *data = dev_id;
+
+	if (surface3_spi_read(data))
+		return IRQ_HANDLED;
+
+	dev_dbg(&data->spi->dev, "%s received -> %*ph\n",
+		__func__, SURFACE3_PACKET_SIZE, data->rd_buf);
+	surface3_spi_process(data);
+
+	return IRQ_HANDLED;
+}
+
+static void surface3_spi_power(struct surface3_ts_data *data, bool on)
+{
+	gpiod_set_value(data->gpiod_rst[0], on);
+	gpiod_set_value(data->gpiod_rst[1], on);
+	/* let the device settle a little */
+	msleep(20);
+}
+
+/**
+ * surface3_spi_get_gpio_config - Get GPIO config from ACPI/DT
+ *
+ * @ts: surface3_spi_ts_data pointer
+ */
+static int surface3_spi_get_gpio_config(struct surface3_ts_data *data)
+{
+	int error;
+	struct device *dev;
+	struct gpio_desc *gpiod;
+	int i;
+
+	dev = &data->spi->dev;
+
+	/* Get the reset lines GPIO pin number */
+	for (i = 0; i < 2; i++) {
+		gpiod = devm_gpiod_get_index(dev, NULL, i, GPIOD_OUT_LOW);
+		if (IS_ERR(gpiod)) {
+			error = PTR_ERR(gpiod);
+			if (error != -EPROBE_DEFER)
+				dev_err(dev,
+					"Failed to get power GPIO %d: %d\n",
+					i,
+					error);
+			return error;
+		}
+
+		data->gpiod_rst[i] = gpiod;
+	}
+
+	return 0;
+}
+
+static int surface3_spi_create_touch_input(struct surface3_ts_data *data)
+{
+	struct input_dev *input;
+	int error;
+
+	input = devm_input_allocate_device(&data->spi->dev);
+	if (!input)
+		return -ENOMEM;
+
+	data->input_dev = input;
+
+	input_set_abs_params(input, ABS_MT_POSITION_X, 0, 9600, 0, 0);
+	input_abs_set_res(input, ABS_MT_POSITION_X, 40);
+	input_set_abs_params(input, ABS_MT_POSITION_Y, 0, 7200, 0, 0);
+	input_abs_set_res(input, ABS_MT_POSITION_Y, 48);
+	input_set_abs_params(input, ABS_MT_WIDTH_MAJOR, 0, 1024, 0, 0);
+	input_set_abs_params(input, ABS_MT_WIDTH_MINOR, 0, 1024, 0, 0);
+	input_mt_init_slots(input, 10, INPUT_MT_DIRECT);
+
+	input->name = "Surface3 SPI Capacitive TouchScreen";
+	input->phys = "input/ts";
+	input->id.bustype = BUS_SPI;
+	input->id.vendor = 0x045e;	/* Microsoft */
+	input->id.product = 0x0001;
+	input->id.version = 0x0000;
+
+	error = input_register_device(input);
+	if (error) {
+		dev_err(&data->spi->dev,
+			"Failed to register input device: %d", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int surface3_spi_create_pen_input(struct surface3_ts_data *data)
+{
+	struct input_dev *input;
+	int error;
+
+	input = devm_input_allocate_device(&data->spi->dev);
+	if (!input)
+		return -ENOMEM;
+
+	data->pen_input_dev = input;
+	data->pen_tool = BTN_TOOL_PEN;
+
+	__set_bit(INPUT_PROP_DIRECT, input->propbit);
+	__set_bit(INPUT_PROP_POINTER, input->propbit);
+	input_set_abs_params(input, ABS_X, 0, 9600, 0, 0);
+	input_abs_set_res(input, ABS_X, 40);
+	input_set_abs_params(input, ABS_Y, 0, 7200, 0, 0);
+	input_abs_set_res(input, ABS_Y, 48);
+	input_set_abs_params(input, ABS_PRESSURE, 0, 1024, 0, 0);
+	input_set_capability(input, EV_KEY, BTN_TOUCH);
+	input_set_capability(input, EV_KEY, BTN_STYLUS);
+	input_set_capability(input, EV_KEY, BTN_TOOL_PEN);
+	input_set_capability(input, EV_KEY, BTN_TOOL_RUBBER);
+
+	input->name = "Surface3 SPI Pen Input";
+	input->phys = "input/ts";
+	input->id.bustype = BUS_SPI;
+	input->id.vendor = 0x045e;     /* Microsoft */
+	input->id.product = 0x0002;
+	input->id.version = 0x0000;
+
+	error = input_register_device(input);
+	if (error) {
+		dev_err(&data->spi->dev,
+			"Failed to register input device: %d", error);
+		return error;
+	}
+
+	return 0;
+}
+
+static int surface3_spi_probe(struct spi_device *spi)
+{
+	struct surface3_ts_data *data;
+	int error;
+
+	/* Set up SPI*/
+	spi->bits_per_word = 8;
+	spi->mode = SPI_MODE_0;
+	error = spi_setup(spi);
+	if (error)
+		return error;
+
+	data = devm_kzalloc(&spi->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->spi = spi;
+	spi_set_drvdata(spi, data);
+
+	error = surface3_spi_get_gpio_config(data);
+	if (error)
+		return error;
+
+	surface3_spi_power(data, true);
+	surface3_spi_power(data, false);
+	surface3_spi_power(data, true);
+
+	error = surface3_spi_create_touch_input(data);
+	if (error)
+		return error;
+
+	error = surface3_spi_create_pen_input(data);
+	if (error)
+		return error;
+
+	error = devm_request_threaded_irq(&spi->dev, spi->irq,
+					  NULL, surface3_spi_irq_handler,
+					  IRQF_ONESHOT,
+					  "Surface3-irq", data);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+static int __maybe_unused surface3_spi_suspend(struct device *dev)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	struct surface3_ts_data *data = spi_get_drvdata(spi);
+
+	disable_irq(data->spi->irq);
+
+	surface3_spi_power(data, false);
+
+	return 0;
+}
+
+static int __maybe_unused surface3_spi_resume(struct device *dev)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	struct surface3_ts_data *data = spi_get_drvdata(spi);
+
+	surface3_spi_power(data, true);
+
+	enable_irq(data->spi->irq);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(surface3_spi_pm_ops,
+			 surface3_spi_suspend,
+			 surface3_spi_resume);
+
+#ifdef CONFIG_ACPI
+static const struct acpi_device_id surface3_spi_acpi_match[] = {
+	{ "MSHW0037", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(acpi, surface3_spi_acpi_match);
+#endif
+
+static struct spi_driver surface3_spi_driver = {
+	.driver = {
+		.name	= "Surface3-spi",
+		.acpi_match_table = ACPI_PTR(surface3_spi_acpi_match),
+		.pm = &surface3_spi_pm_ops,
+	},
+	.probe = surface3_spi_probe,
+};
+
+module_spi_driver(surface3_spi_driver);
+
+MODULE_AUTHOR("Benjamin Tissoires <benjamin.tissoires@gmail.com>");
+MODULE_DESCRIPTION("Surface 3 SPI touchscreen driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index 8b3f15ca7..7953381d9 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -406,7 +406,7 @@ static int titsc_probe(struct platform_device *pdev)
 	int err;
 
 	/* Allocate memory for device */
-	ts_dev = kzalloc(sizeof(struct titsc), GFP_KERNEL);
+	ts_dev = kzalloc(sizeof(*ts_dev), GFP_KERNEL);
 	input_dev = input_allocate_device();
 	if (!ts_dev || !input_dev) {
 		dev_err(&pdev->dev, "failed to allocate memory.\n");
diff --git a/drivers/input/touchscreen/tsc200x-core.c b/drivers/input/touchscreen/tsc200x-core.c
index dfa7f1c4f..b7059ed88 100644
--- a/drivers/input/touchscreen/tsc200x-core.c
+++ b/drivers/input/touchscreen/tsc200x-core.c
@@ -568,7 +568,7 @@ int tsc200x_probe(struct device *dev, int irq, const struct input_id *tsc_id,
 	input_set_abs_params(input_dev, ABS_PRESSURE, 0, max_p, fudge_p, 0);
 
 	if (np)
-		touchscreen_parse_properties(input_dev, false);
+		touchscreen_parse_properties(input_dev, false, NULL);
 
 	input_dev->open = tsc200x_open;
 	input_dev->close = tsc200x_close;
diff --git a/drivers/input/touchscreen/wacom_w8001.c b/drivers/input/touchscreen/wacom_w8001.c
index b6fc4bde7..85e95725d 100644
--- a/drivers/input/touchscreen/wacom_w8001.c
+++ b/drivers/input/touchscreen/wacom_w8001.c
@@ -518,13 +518,21 @@ static int w8001_setup_touch(struct w8001 *w8001, char *basename,
 		w8001->pktlen = W8001_PKTLEN_TOUCH2FG;
 
 		__set_bit(BTN_TOOL_DOUBLETAP, dev->keybit);
-		input_mt_init_slots(dev, 2, 0);
+		error = input_mt_init_slots(dev, 2, 0);
+		if (error) {
+			dev_err(&w8001->serio->dev,
+				"failed to initialize MT slots: %d\n", error);
+			return error;
+		}
+
 		input_set_abs_params(dev, ABS_MT_POSITION_X,
 					0, touch.x, 0, 0);
 		input_set_abs_params(dev, ABS_MT_POSITION_Y,
 					0, touch.y, 0, 0);
 		input_set_abs_params(dev, ABS_MT_TOOL_TYPE,
 					0, MT_TOOL_MAX, 0, 0);
+		input_abs_set_res(dev, ABS_MT_POSITION_X, touch.panel_res);
+		input_abs_set_res(dev, ABS_MT_POSITION_Y, touch.panel_res);
 
 		strlcat(basename, " 2FG", basename_sz);
 		if (w8001->max_pen_x && w8001->max_pen_y)