Initial import

39 files changed, 10331 insertions, 0 deletions

diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
new file mode 100644
index 000000000..e715ae906
--- /dev/null
+++ b/drivers/mtd/maps/Kconfig
@@ -0,0 +1,402 @@
+menu "Mapping drivers for chip access"
+	depends on MTD!=n
+	depends on HAS_IOMEM
+
+config MTD_COMPLEX_MAPPINGS
+	bool "Support non-linear mappings of flash chips"
+	help
+	  This causes the chip drivers to allow for complicated
+	  paged mappings of flash chips.
+
+config MTD_PHYSMAP
+	tristate "Flash device in physical memory map"
+	depends on MTD_CFI || MTD_JEDECPROBE || MTD_ROM || MTD_LPDDR
+	help
+	  This provides a 'mapping' driver which allows the NOR Flash and
+	  ROM driver code to communicate with chips which are mapped
+	  physically into the CPU's memory. You will need to configure
+	  the physical address and size of the flash chips on your
+	  particular board as well as the bus width, either statically
+	  with config options or at run-time.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called physmap.
+
+config MTD_PHYSMAP_COMPAT
+	bool "Physmap compat support"
+	depends on MTD_PHYSMAP
+	default n
+	help
+	  Setup a simple mapping via the Kconfig options.  Normally the
+	  physmap configuration options are done via your board's
+	  resource file.
+
+	  If unsure, say N here.
+
+config MTD_PHYSMAP_START
+	hex "Physical start address of flash mapping"
+	depends on MTD_PHYSMAP_COMPAT
+	default "0x8000000"
+	help
+	  This is the physical memory location at which the flash chips
+	  are mapped on your particular target board. Refer to the
+	  memory map which should hopefully be in the documentation for
+	  your board.
+
+config MTD_PHYSMAP_LEN
+	hex "Physical length of flash mapping"
+	depends on MTD_PHYSMAP_COMPAT
+	default "0"
+	help
+	  This is the total length of the mapping of the flash chips on
+	  your particular board. If there is space, or aliases, in the
+	  physical memory map between the chips, this could be larger
+	  than the total amount of flash present. Refer to the memory
+	  map which should hopefully be in the documentation for your
+	  board.
+
+config MTD_PHYSMAP_BANKWIDTH
+	int "Bank width in octets"
+	depends on MTD_PHYSMAP_COMPAT
+	default "2"
+	help
+	  This is the total width of the data bus of the flash devices
+	  in octets. For example, if you have a data bus width of 32
+	  bits, you would set the bus width octet value to 4. This is
+	  used internally by the CFI drivers.
+
+config MTD_PHYSMAP_OF
+	tristate "Memory device in physical memory map based on OF description"
+	depends on OF && (MTD_CFI || MTD_JEDECPROBE || MTD_ROM || MTD_RAM)
+	help
+	  This provides a 'mapping' driver which allows the NOR Flash, ROM
+	  and RAM driver code to communicate with chips which are mapped
+	  physically into the CPU's memory. The mapping description here is
+	  taken from OF device tree.
+
+config MTD_PMC_MSP_EVM
+	tristate "CFI Flash device mapped on PMC-Sierra MSP"
+	depends on PMC_MSP && MTD_CFI
+	help
+	  This provides a 'mapping' driver which supports the way
+	  in which user-programmable flash chips are connected on the
+	  PMC-Sierra MSP eval/demo boards.
+
+choice
+	prompt "Maximum mappable memory available for flash IO"
+	depends on MTD_PMC_MSP_EVM
+	default MSP_FLASH_MAP_LIMIT_32M
+
+config MSP_FLASH_MAP_LIMIT_32M
+	bool "32M"
+
+endchoice
+
+config MSP_FLASH_MAP_LIMIT
+	hex
+	default "0x02000000"
+	depends on MSP_FLASH_MAP_LIMIT_32M
+
+config MTD_SUN_UFLASH
+	tristate "Sun Microsystems userflash support"
+	depends on SPARC && MTD_CFI && PCI
+	help
+	  This provides a 'mapping' driver which supports the way in
+	  which user-programmable flash chips are connected on various
+	  Sun Microsystems boardsets.  This driver will require CFI support
+	  in the kernel, so if you did not enable CFI previously, do that now.
+
+config MTD_SC520CDP
+	tristate "CFI Flash device mapped on AMD SC520 CDP"
+	depends on (MELAN || COMPILE_TEST) && MTD_CFI
+	help
+	  The SC520 CDP board has two banks of CFI-compliant chips and one
+	  Dual-in-line JEDEC chip. This 'mapping' driver supports that
+	  arrangement, implementing three MTD devices.
+
+config MTD_NETSC520
+	tristate "CFI Flash device mapped on AMD NetSc520"
+	depends on (MELAN || COMPILE_TEST) && MTD_CFI
+	help
+	  This enables access routines for the flash chips on the AMD NetSc520
+	  demonstration board. If you have one of these boards and would like
+	  to use the flash chips on it, say 'Y'.
+
+config MTD_TS5500
+	tristate "JEDEC Flash device mapped on Technologic Systems TS-5500"
+	depends on TS5500 || COMPILE_TEST
+	select MTD_JEDECPROBE
+	select MTD_CFI_AMDSTD
+	help
+	  This provides a driver for the on-board flash of the Technologic
+	  System's TS-5500 board. The 2MB flash is split into 3 partitions
+	  which are accessed as separate MTD devices.
+
+	  mtd0 and mtd2 are the two BIOS drives, which use the resident
+	  flash disk (RFD) flash translation layer.
+
+	  mtd1 allows you to reprogram your BIOS. BE VERY CAREFUL.
+
+	  Note that jumper 3 ("Write Enable Drive A") must be set
+	  otherwise detection won't succeed.
+
+config MTD_SBC_GXX
+	tristate "CFI Flash device mapped on Arcom SBC-GXx boards"
+	depends on X86 && MTD_CFI_INTELEXT && MTD_COMPLEX_MAPPINGS
+	help
+	  This provides a driver for the on-board flash of Arcom Control
+	  Systems' SBC-GXn family of boards, formerly known as SBC-MediaGX.
+	  By default the flash is split into 3 partitions which are accessed
+	  as separate MTD devices. This board utilizes Intel StrataFlash.
+	  More info at
+	  <http://www.arcomcontrols.com/products/icp/pc104/processors/SBC_GX1.htm>.
+
+config MTD_PXA2XX
+	tristate "CFI Flash device mapped on Intel XScale PXA2xx based boards"
+	depends on (PXA25x || PXA27x) && MTD_CFI_INTELEXT
+	help
+	  This provides a driver for the NOR flash attached to a PXA2xx chip.
+
+config MTD_SCx200_DOCFLASH
+	tristate "Flash device mapped with DOCCS on NatSemi SCx200"
+	depends on SCx200 && MTD_CFI
+	help
+	  Enable support for a flash chip mapped using the DOCCS signal on a
+	  National Semiconductor SCx200 processor.
+
+	  If you don't know what to do here, say N.
+
+	  If compiled as a module, it will be called scx200_docflash.
+
+config MTD_AMD76XROM
+	tristate "BIOS flash chip on AMD76x southbridge"
+	depends on X86 && MTD_JEDECPROBE
+	help
+	  Support for treating the BIOS flash chip on AMD76x motherboards
+	  as an MTD device - with this you can reprogram your BIOS.
+
+	  BE VERY CAREFUL.
+
+config MTD_ICHXROM
+	tristate "BIOS flash chip on Intel Controller Hub 2/3/4/5"
+	depends on X86 && MTD_JEDECPROBE
+	help
+	  Support for treating the BIOS flash chip on ICHX motherboards
+	  as an MTD device - with this you can reprogram your BIOS.
+
+	  BE VERY CAREFUL.
+
+config MTD_ESB2ROM
+        tristate "BIOS flash chip on Intel ESB Controller Hub 2"
+        depends on X86 && MTD_JEDECPROBE && PCI
+        help
+          Support for treating the BIOS flash chip on ESB2 motherboards
+          as an MTD device - with this you can reprogram your BIOS.
+
+          BE VERY CAREFUL.
+
+config MTD_CK804XROM
+	tristate "BIOS flash chip on Nvidia CK804"
+	depends on X86 && MTD_JEDECPROBE && PCI
+	help
+	  Support for treating the BIOS flash chip on nvidia motherboards
+	  as an MTD device - with this you can reprogram your BIOS.
+
+	  BE VERY CAREFUL.
+
+config MTD_SCB2_FLASH
+	tristate "BIOS flash chip on Intel SCB2 boards"
+	depends on X86 && MTD_JEDECPROBE && PCI
+	help
+	  Support for treating the BIOS flash chip on Intel SCB2 boards
+	  as an MTD device - with this you can reprogram your BIOS.
+
+	  BE VERY CAREFUL.
+
+config MTD_TSUNAMI
+	tristate "Flash chips on Tsunami TIG bus"
+	depends on ALPHA_TSUNAMI && MTD_COMPLEX_MAPPINGS
+	help
+	  Support for the flash chip on Tsunami TIG bus.
+
+config MTD_NETtel
+	tristate "CFI flash device on SnapGear/SecureEdge"
+	depends on X86 && MTD_JEDECPROBE
+	help
+	  Support for flash chips on NETtel/SecureEdge/SnapGear boards.
+
+config MTD_LANTIQ
+	tristate "Lantiq SoC NOR support"
+	depends on LANTIQ
+	help
+	  Support for NOR flash attached to the Lantiq SoC's External Bus Unit.
+
+config MTD_L440GX
+	tristate "BIOS flash chip on Intel L440GX boards"
+	depends on X86 && MTD_JEDECPROBE
+	help
+	  Support for treating the BIOS flash chip on Intel L440GX motherboards
+	  as an MTD device - with this you can reprogram your BIOS.
+
+	  BE VERY CAREFUL.
+
+config MTD_CFI_FLAGADM
+	tristate "CFI Flash device mapping on FlagaDM"
+	depends on PPC_8xx && MTD_CFI
+	help
+	  Mapping for the Flaga digital module. If you don't have one, ignore
+	  this setting.
+
+config MTD_SOLUTIONENGINE
+	tristate "CFI Flash device mapped on Hitachi SolutionEngine"
+	depends on SOLUTION_ENGINE && MTD_CFI && MTD_REDBOOT_PARTS
+	help
+	  This enables access to the flash chips on the Hitachi SolutionEngine and
+	  similar boards. Say 'Y' if you are building a kernel for such a board.
+
+config MTD_SA1100
+	tristate "CFI Flash device mapped on StrongARM SA11x0"
+	depends on MTD_CFI && ARCH_SA1100
+	help
+	  This enables access to the flash chips on most platforms based on
+	  the SA1100 and SA1110, including the Assabet and the Compaq iPAQ.
+	  If you have such a board, say 'Y'.
+
+config MTD_DC21285
+	tristate "CFI Flash device mapped on DC21285 Footbridge"
+	depends on MTD_CFI && ARCH_FOOTBRIDGE && MTD_COMPLEX_MAPPINGS
+	help
+	  This provides a driver for the flash accessed using Intel's
+	  21285 bridge used with Intel's StrongARM processors. More info at
+	  <http://www.intel.com/design/bridge/docs/21285_documentation.htm>.
+
+config MTD_IXP4XX
+	tristate "CFI Flash device mapped on Intel IXP4xx based systems"
+	depends on MTD_CFI && MTD_COMPLEX_MAPPINGS && ARCH_IXP4XX
+	help
+	  This enables MTD access to flash devices on platforms based
+	  on Intel's IXP4xx family of network processors such as the
+	  IXDP425 and Coyote. If you have an IXP4xx based board and
+	  would like to use the flash chips on it, say 'Y'.
+
+config MTD_IMPA7
+	tristate "JEDEC Flash device mapped on impA7"
+	depends on ARM && MTD_JEDECPROBE
+	help
+	  This enables access to the NOR Flash on the impA7 board of
+	  implementa GmbH. If you have such a board, say 'Y' here.
+
+# This needs CFI or JEDEC, depending on the cards found.
+config MTD_PCI
+	tristate "PCI MTD driver"
+	depends on PCI && MTD_COMPLEX_MAPPINGS
+	help
+	  Mapping for accessing flash devices on add-in cards like the Intel XScale
+	  IQ80310 card, and the Intel EBSA285 card in blank ROM programming mode
+	  (please see the manual for the link settings).
+
+	  If you are not sure, say N.
+
+config MTD_PCMCIA
+	tristate "PCMCIA MTD driver"
+	depends on PCMCIA && MTD_COMPLEX_MAPPINGS
+	help
+	  Map driver for accessing PCMCIA linear flash memory cards. These
+	  cards are usually around 4-16MiB in size. This does not include
+	  Compact Flash cards which are treated as IDE devices.
+
+config MTD_PCMCIA_ANONYMOUS
+	bool "Use PCMCIA MTD drivers for anonymous PCMCIA cards"
+	depends on MTD_PCMCIA
+	help
+	  If this option is enabled, PCMCIA cards which do not report
+	  anything about themselves are assumed to be MTD cards.
+
+	  If unsure, say N.
+
+config MTD_BFIN_ASYNC
+	tristate "Blackfin BF533-STAMP Flash Chip Support"
+	depends on BFIN533_STAMP && MTD_CFI && MTD_COMPLEX_MAPPINGS
+	default y
+	help
+	  Map driver which allows for simultaneous utilization of
+	  ethernet and CFI parallel flash.
+
+	  If compiled as a module, it will be called bfin-async-flash.
+
+config MTD_GPIO_ADDR
+	tristate "GPIO-assisted Flash Chip Support"
+	depends on GPIOLIB
+	depends on MTD_COMPLEX_MAPPINGS
+	help
+	  Map driver which allows flashes to be partially physically addressed
+	  and assisted by GPIOs.
+
+	  If compiled as a module, it will be called gpio-addr-flash.
+
+config MTD_UCLINUX
+	bool "Generic uClinux RAM/ROM filesystem support"
+	depends on (MTD_RAM=y || MTD_ROM=y) && (!MMU || COLDFIRE)
+	help
+	  Map driver to support image based filesystems for uClinux.
+
+config MTD_INTEL_VR_NOR
+	tristate "NOR flash on Intel Vermilion Range Expansion Bus CS0"
+	depends on PCI
+	help
+	  Map driver for a NOR flash bank located on the Expansion Bus of the
+	  Intel Vermilion Range chipset.
+
+config MTD_RBTX4939
+	tristate "Map driver for RBTX4939 board"
+	depends on TOSHIBA_RBTX4939 && MTD_CFI && MTD_COMPLEX_MAPPINGS
+	help
+	  Map driver for NOR flash chips on RBTX4939 board.
+
+config MTD_PLATRAM
+	tristate "Map driver for platform device RAM (mtd-ram)"
+	select MTD_RAM
+	help
+	  Map driver for RAM areas described via the platform device
+	  system.
+
+	  This selection automatically selects the map_ram driver.
+
+config MTD_VMU
+	tristate "Map driver for Dreamcast VMU"
+	depends on MAPLE
+	help
+	  This driver enables access to the Dreamcast Visual Memory Unit (VMU).
+
+	  Most Dreamcast users will want to say Y here.
+
+	  To build this as a module select M here, the module will be called
+	  vmu-flash.
+
+config MTD_PISMO
+	tristate "MTD discovery driver for PISMO modules"
+	depends on I2C
+	depends on ARCH_VERSATILE
+	help
+	  This driver allows for discovery of PISMO modules - see
+	  <http://www.pismoworld.org/>.  These are small modules containing
+	  up to five memory devices (eg, SRAM, flash, DOC) described by an
+	  I2C EEPROM.
+
+	  This driver does not create any MTD maps itself; instead it
+	  creates MTD physmap and MTD SRAM platform devices.  If you
+	  enable this option, you should consider enabling MTD_PHYSMAP
+	  and/or MTD_PLATRAM according to the devices on your module.
+
+	  When built as a module, it will be called pismo.ko
+
+config MTD_LATCH_ADDR
+        tristate "Latch-assisted Flash Chip Support"
+        depends on MTD_COMPLEX_MAPPINGS
+        help
+          Map driver which allows flashes to be partially physically addressed
+          and have the upper address lines set by a board specific code.
+
+          If compiled as a module, it will be called latch-addr-flash.
+
+endmenu
diff --git a/drivers/mtd/maps/Makefile b/drivers/mtd/maps/Makefile
new file mode 100644
index 000000000..141c91a5b
--- /dev/null
+++ b/drivers/mtd/maps/Makefile
@@ -0,0 +1,45 @@
+#
+# linux/drivers/maps/Makefile
+#
+
+ifeq ($(CONFIG_MTD_COMPLEX_MAPPINGS),y)
+obj-$(CONFIG_MTD)		+= map_funcs.o
+endif
+
+# Chip mappings
+obj-$(CONFIG_MTD_CFI_FLAGADM)	+= cfi_flagadm.o
+obj-$(CONFIG_MTD_DC21285)	+= dc21285.o
+obj-$(CONFIG_MTD_L440GX)	+= l440gx.o
+obj-$(CONFIG_MTD_AMD76XROM)	+= amd76xrom.o
+obj-$(CONFIG_MTD_ESB2ROM)	+= esb2rom.o
+obj-$(CONFIG_MTD_ICHXROM)	+= ichxrom.o
+obj-$(CONFIG_MTD_CK804XROM)	+= ck804xrom.o
+obj-$(CONFIG_MTD_TSUNAMI)	+= tsunami_flash.o
+obj-$(CONFIG_MTD_PXA2XX)	+= pxa2xx-flash.o
+obj-$(CONFIG_MTD_PHYSMAP)	+= physmap.o
+obj-$(CONFIG_MTD_PHYSMAP_OF)	+= physmap_of.o
+obj-$(CONFIG_MTD_PISMO)		+= pismo.o
+obj-$(CONFIG_MTD_PMC_MSP_EVM)   += pmcmsp-flash.o
+obj-$(CONFIG_MTD_PCMCIA)	+= pcmciamtd.o
+obj-$(CONFIG_MTD_SA1100)	+= sa1100-flash.o
+obj-$(CONFIG_MTD_SBC_GXX)	+= sbc_gxx.o
+obj-$(CONFIG_MTD_SC520CDP)	+= sc520cdp.o
+obj-$(CONFIG_MTD_NETSC520)	+= netsc520.o
+obj-$(CONFIG_MTD_TS5500)	+= ts5500_flash.o
+obj-$(CONFIG_MTD_SUN_UFLASH)	+= sun_uflash.o
+obj-$(CONFIG_MTD_SCx200_DOCFLASH)+= scx200_docflash.o
+obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
+obj-$(CONFIG_MTD_PCI)		+= pci.o
+obj-$(CONFIG_MTD_IMPA7)		+= impa7.o
+obj-$(CONFIG_MTD_UCLINUX)	+= uclinux.o
+obj-$(CONFIG_MTD_NETtel)	+= nettel.o
+obj-$(CONFIG_MTD_SCB2_FLASH)	+= scb2_flash.o
+obj-$(CONFIG_MTD_IXP4XX)	+= ixp4xx.o
+obj-$(CONFIG_MTD_PLATRAM)	+= plat-ram.o
+obj-$(CONFIG_MTD_INTEL_VR_NOR)	+= intel_vr_nor.o
+obj-$(CONFIG_MTD_BFIN_ASYNC)	+= bfin-async-flash.o
+obj-$(CONFIG_MTD_RBTX4939)	+= rbtx4939-flash.o
+obj-$(CONFIG_MTD_VMU)		+= vmu-flash.o
+obj-$(CONFIG_MTD_GPIO_ADDR)	+= gpio-addr-flash.o
+obj-$(CONFIG_MTD_LATCH_ADDR)	+= latch-addr-flash.o
+obj-$(CONFIG_MTD_LANTIQ)	+= lantiq-flash.o
diff --git a/drivers/mtd/maps/amd76xrom.c b/drivers/mtd/maps/amd76xrom.c
new file mode 100644
index 000000000..f7207b0a7
--- /dev/null
+++ b/drivers/mtd/maps/amd76xrom.c
@@ -0,0 +1,349 @@
+/*
+ * amd76xrom.c
+ *
+ * Normal mappings of chips in physical memory
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/flashchip.h>
+#include <linux/pci.h>
+#include <linux/pci_ids.h>
+#include <linux/list.h>
+
+
+#define xstr(s) str(s)
+#define str(s) #s
+#define MOD_NAME xstr(KBUILD_BASENAME)
+
+#define ADDRESS_NAME_LEN 18
+
+#define ROM_PROBE_STEP_SIZE (64*1024) /* 64KiB */
+
+struct amd76xrom_window {
+	void __iomem *virt;
+	unsigned long phys;
+	unsigned long size;
+	struct list_head maps;
+	struct resource rsrc;
+	struct pci_dev *pdev;
+};
+
+struct amd76xrom_map_info {
+	struct list_head list;
+	struct map_info map;
+	struct mtd_info *mtd;
+	struct resource rsrc;
+	char map_name[sizeof(MOD_NAME) + 2 + ADDRESS_NAME_LEN];
+};
+
+/* The 2 bits controlling the window size are often set to allow reading
+ * the BIOS, but too small to allow writing, since the lock registers are
+ * 4MiB lower in the address space than the data.
+ *
+ * This is intended to prevent flashing the bios, perhaps accidentally.
+ *
+ * This parameter allows the normal driver to over-ride the BIOS settings.
+ *
+ * The bits are 6 and 7.  If both bits are set, it is a 5MiB window.
+ * If only the 7 Bit is set, it is a 4MiB window.  Otherwise, a
+ * 64KiB window.
+ *
+ */
+static uint win_size_bits;
+module_param(win_size_bits, uint, 0);
+MODULE_PARM_DESC(win_size_bits, "ROM window size bits override for 0x43 byte, normally set by BIOS.");
+
+static struct amd76xrom_window amd76xrom_window = {
+	.maps = LIST_HEAD_INIT(amd76xrom_window.maps),
+};
+
+static void amd76xrom_cleanup(struct amd76xrom_window *window)
+{
+	struct amd76xrom_map_info *map, *scratch;
+	u8 byte;
+
+	if (window->pdev) {
+		/* Disable writes through the rom window */
+		pci_read_config_byte(window->pdev, 0x40, &byte);
+		pci_write_config_byte(window->pdev, 0x40, byte & ~1);
+		pci_dev_put(window->pdev);
+	}
+
+	/* Free all of the mtd devices */
+	list_for_each_entry_safe(map, scratch, &window->maps, list) {
+		if (map->rsrc.parent) {
+			release_resource(&map->rsrc);
+		}
+		mtd_device_unregister(map->mtd);
+		map_destroy(map->mtd);
+		list_del(&map->list);
+		kfree(map);
+	}
+	if (window->rsrc.parent)
+		release_resource(&window->rsrc);
+
+	if (window->virt) {
+		iounmap(window->virt);
+		window->virt = NULL;
+		window->phys = 0;
+		window->size = 0;
+		window->pdev = NULL;
+	}
+}
+
+
+static int amd76xrom_init_one(struct pci_dev *pdev,
+			      const struct pci_device_id *ent)
+{
+	static char *rom_probe_types[] = { "cfi_probe", "jedec_probe", NULL };
+	u8 byte;
+	struct amd76xrom_window *window = &amd76xrom_window;
+	struct amd76xrom_map_info *map = NULL;
+	unsigned long map_top;
+
+	/* Remember the pci dev I find the window in - already have a ref */
+	window->pdev = pdev;
+
+	/* Enable the selected rom window.  This is often incorrectly
+	 * set up by the BIOS, and the 4MiB offset for the lock registers
+	 * requires the full 5MiB of window space.
+	 *
+	 * This 'write, then read' approach leaves the bits for
+	 * other uses of the hardware info.
+	 */
+	pci_read_config_byte(pdev, 0x43, &byte);
+	pci_write_config_byte(pdev, 0x43, byte | win_size_bits );
+
+	/* Assume the rom window is properly setup, and find it's size */
+	pci_read_config_byte(pdev, 0x43, &byte);
+	if ((byte & ((1<<7)|(1<<6))) == ((1<<7)|(1<<6))) {
+		window->phys = 0xffb00000; /* 5MiB */
+	}
+	else if ((byte & (1<<7)) == (1<<7)) {
+		window->phys = 0xffc00000; /* 4MiB */
+	}
+	else {
+		window->phys = 0xffff0000; /* 64KiB */
+	}
+	window->size = 0xffffffffUL - window->phys + 1UL;
+
+	/*
+	 * Try to reserve the window mem region.  If this fails then
+	 * it is likely due to a fragment of the window being
+	 * "reseved" by the BIOS.  In the case that the
+	 * request_mem_region() fails then once the rom size is
+	 * discovered we will try to reserve the unreserved fragment.
+	 */
+	window->rsrc.name = MOD_NAME;
+	window->rsrc.start = window->phys;
+	window->rsrc.end   = window->phys + window->size - 1;
+	window->rsrc.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+	if (request_resource(&iomem_resource, &window->rsrc)) {
+		window->rsrc.parent = NULL;
+		printk(KERN_ERR MOD_NAME
+		       " %s(): Unable to register resource %pR - kernel bug?\n",
+		       __func__, &window->rsrc);
+		return -EBUSY;
+	}
+
+
+	/* Enable writes through the rom window */
+	pci_read_config_byte(pdev, 0x40, &byte);
+	pci_write_config_byte(pdev, 0x40, byte | 1);
+
+	/* FIXME handle registers 0x80 - 0x8C the bios region locks */
+
+	/* For write accesses caches are useless */
+	window->virt = ioremap_nocache(window->phys, window->size);
+	if (!window->virt) {
+		printk(KERN_ERR MOD_NAME ": ioremap(%08lx, %08lx) failed\n",
+			window->phys, window->size);
+		goto out;
+	}
+
+	/* Get the first address to look for an rom chip at */
+	map_top = window->phys;
+#if 1
+	/* The probe sequence run over the firmware hub lock
+	 * registers sets them to 0x7 (no access).
+	 * Probe at most the last 4M of the address space.
+	 */
+	if (map_top < 0xffc00000) {
+		map_top = 0xffc00000;
+	}
+#endif
+	/* Loop  through and look for rom chips */
+	while((map_top - 1) < 0xffffffffUL) {
+		struct cfi_private *cfi;
+		unsigned long offset;
+		int i;
+
+		if (!map) {
+			map = kmalloc(sizeof(*map), GFP_KERNEL);
+		}
+		if (!map) {
+			printk(KERN_ERR MOD_NAME ": kmalloc failed");
+			goto out;
+		}
+		memset(map, 0, sizeof(*map));
+		INIT_LIST_HEAD(&map->list);
+		map->map.name = map->map_name;
+		map->map.phys = map_top;
+		offset = map_top - window->phys;
+		map->map.virt = (void __iomem *)
+			(((unsigned long)(window->virt)) + offset);
+		map->map.size = 0xffffffffUL - map_top + 1UL;
+		/* Set the name of the map to the address I am trying */
+		sprintf(map->map_name, "%s @%08Lx",
+			MOD_NAME, (unsigned long long)map->map.phys);
+
+		/* There is no generic VPP support */
+		for(map->map.bankwidth = 32; map->map.bankwidth;
+			map->map.bankwidth >>= 1)
+		{
+			char **probe_type;
+			/* Skip bankwidths that are not supported */
+			if (!map_bankwidth_supported(map->map.bankwidth))
+				continue;
+
+			/* Setup the map methods */
+			simple_map_init(&map->map);
+
+			/* Try all of the probe methods */
+			probe_type = rom_probe_types;
+			for(; *probe_type; probe_type++) {
+				map->mtd = do_map_probe(*probe_type, &map->map);
+				if (map->mtd)
+					goto found;
+			}
+		}
+		map_top += ROM_PROBE_STEP_SIZE;
+		continue;
+	found:
+		/* Trim the size if we are larger than the map */
+		if (map->mtd->size > map->map.size) {
+			printk(KERN_WARNING MOD_NAME
+				" rom(%llu) larger than window(%lu). fixing...\n",
+				(unsigned long long)map->mtd->size, map->map.size);
+			map->mtd->size = map->map.size;
+		}
+		if (window->rsrc.parent) {
+			/*
+			 * Registering the MTD device in iomem may not be possible
+			 * if there is a BIOS "reserved" and BUSY range.  If this
+			 * fails then continue anyway.
+			 */
+			map->rsrc.name  = map->map_name;
+			map->rsrc.start = map->map.phys;
+			map->rsrc.end   = map->map.phys + map->mtd->size - 1;
+			map->rsrc.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+			if (request_resource(&window->rsrc, &map->rsrc)) {
+				printk(KERN_ERR MOD_NAME
+					": cannot reserve MTD resource\n");
+				map->rsrc.parent = NULL;
+			}
+		}
+
+		/* Make the whole region visible in the map */
+		map->map.virt = window->virt;
+		map->map.phys = window->phys;
+		cfi = map->map.fldrv_priv;
+		for(i = 0; i < cfi->numchips; i++) {
+			cfi->chips[i].start += offset;
+		}
+
+		/* Now that the mtd devices is complete claim and export it */
+		map->mtd->owner = THIS_MODULE;
+		if (mtd_device_register(map->mtd, NULL, 0)) {
+			map_destroy(map->mtd);
+			map->mtd = NULL;
+			goto out;
+		}
+
+
+		/* Calculate the new value of map_top */
+		map_top += map->mtd->size;
+
+		/* File away the map structure */
+		list_add(&map->list, &window->maps);
+		map = NULL;
+	}
+
+ out:
+	/* Free any left over map structures */
+	kfree(map);
+	/* See if I have any map structures */
+	if (list_empty(&window->maps)) {
+		amd76xrom_cleanup(window);
+		return -ENODEV;
+	}
+	return 0;
+}
+
+
+static void amd76xrom_remove_one(struct pci_dev *pdev)
+{
+	struct amd76xrom_window *window = &amd76xrom_window;
+
+	amd76xrom_cleanup(window);
+}
+
+static struct pci_device_id amd76xrom_pci_tbl[] = {
+	{ PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7410,
+		PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7440,
+		PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_AMD, 0x7468 }, /* amd8111 support */
+	{ 0, }
+};
+
+MODULE_DEVICE_TABLE(pci, amd76xrom_pci_tbl);
+
+#if 0
+static struct pci_driver amd76xrom_driver = {
+	.name =		MOD_NAME,
+	.id_table =	amd76xrom_pci_tbl,
+	.probe =	amd76xrom_init_one,
+	.remove =	amd76xrom_remove_one,
+};
+#endif
+
+static int __init init_amd76xrom(void)
+{
+	struct pci_dev *pdev;
+	struct pci_device_id *id;
+	pdev = NULL;
+	for(id = amd76xrom_pci_tbl; id->vendor; id++) {
+		pdev = pci_get_device(id->vendor, id->device, NULL);
+		if (pdev) {
+			break;
+		}
+	}
+	if (pdev) {
+		return amd76xrom_init_one(pdev, &amd76xrom_pci_tbl[0]);
+	}
+	return -ENXIO;
+#if 0
+	return pci_register_driver(&amd76xrom_driver);
+#endif
+}
+
+static void __exit cleanup_amd76xrom(void)
+{
+	amd76xrom_remove_one(amd76xrom_window.pdev);
+}
+
+module_init(init_amd76xrom);
+module_exit(cleanup_amd76xrom);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Eric Biederman <ebiederman@lnxi.com>");
+MODULE_DESCRIPTION("MTD map driver for BIOS chips on the AMD76X southbridge");
diff --git a/drivers/mtd/maps/bfin-async-flash.c b/drivers/mtd/maps/bfin-async-flash.c
new file mode 100644
index 000000000..41730feea
--- /dev/null
+++ b/drivers/mtd/maps/bfin-async-flash.c
@@ -0,0 +1,196 @@
+/*
+ * drivers/mtd/maps/bfin-async-flash.c
+ *
+ * Handle the case where flash memory and ethernet mac/phy are
+ * mapped onto the same async bank.  The BF533-STAMP does this
+ * for example.  All board-specific configuration goes in your
+ * board resources file.
+ *
+ * Copyright 2000 Nicolas Pitre <nico@fluxnic.net>
+ * Copyright 2005-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#include <asm/blackfin.h>
+#include <linux/gpio.h>
+#include <linux/io.h>
+#include <asm/unaligned.h>
+
+#define pr_devinit(fmt, args...) \
+		({ static const char __fmt[] = fmt; printk(__fmt, ## args); })
+
+#define DRIVER_NAME "bfin-async-flash"
+
+struct async_state {
+	struct mtd_info *mtd;
+	struct map_info map;
+	int enet_flash_pin;
+	uint32_t flash_ambctl0, flash_ambctl1;
+	uint32_t save_ambctl0, save_ambctl1;
+	unsigned long irq_flags;
+};
+
+static void switch_to_flash(struct async_state *state)
+{
+	local_irq_save(state->irq_flags);
+
+	gpio_set_value(state->enet_flash_pin, 0);
+
+	state->save_ambctl0 = bfin_read_EBIU_AMBCTL0();
+	state->save_ambctl1 = bfin_read_EBIU_AMBCTL1();
+	bfin_write_EBIU_AMBCTL0(state->flash_ambctl0);
+	bfin_write_EBIU_AMBCTL1(state->flash_ambctl1);
+	SSYNC();
+}
+
+static void switch_back(struct async_state *state)
+{
+	bfin_write_EBIU_AMBCTL0(state->save_ambctl0);
+	bfin_write_EBIU_AMBCTL1(state->save_ambctl1);
+	SSYNC();
+
+	gpio_set_value(state->enet_flash_pin, 1);
+
+	local_irq_restore(state->irq_flags);
+}
+
+static map_word bfin_flash_read(struct map_info *map, unsigned long ofs)
+{
+	struct async_state *state = (struct async_state *)map->map_priv_1;
+	uint16_t word;
+	map_word test;
+
+	switch_to_flash(state);
+
+	word = readw(map->virt + ofs);
+
+	switch_back(state);
+
+	test.x[0] = word;
+	return test;
+}
+
+static void bfin_flash_copy_from(struct map_info *map, void *to, unsigned long from, ssize_t len)
+{
+	struct async_state *state = (struct async_state *)map->map_priv_1;
+
+	switch_to_flash(state);
+
+	memcpy(to, map->virt + from, len);
+
+	switch_back(state);
+}
+
+static void bfin_flash_write(struct map_info *map, map_word d1, unsigned long ofs)
+{
+	struct async_state *state = (struct async_state *)map->map_priv_1;
+	uint16_t d;
+
+	d = d1.x[0];
+
+	switch_to_flash(state);
+
+	writew(d, map->virt + ofs);
+	SSYNC();
+
+	switch_back(state);
+}
+
+static void bfin_flash_copy_to(struct map_info *map, unsigned long to, const void *from, ssize_t len)
+{
+	struct async_state *state = (struct async_state *)map->map_priv_1;
+
+	switch_to_flash(state);
+
+	memcpy(map->virt + to, from, len);
+	SSYNC();
+
+	switch_back(state);
+}
+
+static const char * const part_probe_types[] = {
+	"cmdlinepart", "RedBoot", NULL };
+
+static int bfin_flash_probe(struct platform_device *pdev)
+{
+	struct physmap_flash_data *pdata = dev_get_platdata(&pdev->dev);
+	struct resource *memory = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	struct resource *flash_ambctl = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	struct async_state *state;
+
+	state = kzalloc(sizeof(*state), GFP_KERNEL);
+	if (!state)
+		return -ENOMEM;
+
+	state->map.name       = DRIVER_NAME;
+	state->map.read       = bfin_flash_read;
+	state->map.copy_from  = bfin_flash_copy_from;
+	state->map.write      = bfin_flash_write;
+	state->map.copy_to    = bfin_flash_copy_to;
+	state->map.bankwidth  = pdata->width;
+	state->map.size       = resource_size(memory);
+	state->map.virt       = (void __iomem *)memory->start;
+	state->map.phys       = memory->start;
+	state->map.map_priv_1 = (unsigned long)state;
+	state->enet_flash_pin = platform_get_irq(pdev, 0);
+	state->flash_ambctl0  = flash_ambctl->start;
+	state->flash_ambctl1  = flash_ambctl->end;
+
+	if (gpio_request(state->enet_flash_pin, DRIVER_NAME)) {
+		pr_devinit(KERN_ERR DRIVER_NAME ": Failed to request gpio %d\n", state->enet_flash_pin);
+		kfree(state);
+		return -EBUSY;
+	}
+	gpio_direction_output(state->enet_flash_pin, 1);
+
+	pr_devinit(KERN_NOTICE DRIVER_NAME ": probing %d-bit flash bus\n", state->map.bankwidth * 8);
+	state->mtd = do_map_probe(memory->name, &state->map);
+	if (!state->mtd) {
+		gpio_free(state->enet_flash_pin);
+		kfree(state);
+		return -ENXIO;
+	}
+
+	mtd_device_parse_register(state->mtd, part_probe_types, NULL,
+				  pdata->parts, pdata->nr_parts);
+
+	platform_set_drvdata(pdev, state);
+
+	return 0;
+}
+
+static int bfin_flash_remove(struct platform_device *pdev)
+{
+	struct async_state *state = platform_get_drvdata(pdev);
+	gpio_free(state->enet_flash_pin);
+	mtd_device_unregister(state->mtd);
+	map_destroy(state->mtd);
+	kfree(state);
+	return 0;
+}
+
+static struct platform_driver bfin_flash_driver = {
+	.probe		= bfin_flash_probe,
+	.remove		= bfin_flash_remove,
+	.driver		= {
+		.name	= DRIVER_NAME,
+	},
+};
+
+module_platform_driver(bfin_flash_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("MTD map driver for Blackfins with flash/ethernet on same async bank");
diff --git a/drivers/mtd/maps/cfi_flagadm.c b/drivers/mtd/maps/cfi_flagadm.c
new file mode 100644
index 000000000..d504b3d17
--- /dev/null
+++ b/drivers/mtd/maps/cfi_flagadm.c
@@ -0,0 +1,137 @@
+/*
+ *  Copyright © 2001 Flaga hf. Medical Devices, Kári Davíðsson <kd@flaga.is>
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+
+/* We split the flash chip up into four parts.
+ * 1: bootloader first 128k			(0x00000000 - 0x0001FFFF) size 0x020000
+ * 2: kernel 640k					(0x00020000 - 0x000BFFFF) size 0x0A0000
+ * 3: compressed 1536k root ramdisk	(0x000C0000 - 0x0023FFFF) size 0x180000
+ * 4: writeable diskpartition (jffs)(0x00240000 - 0x003FFFFF) size 0x1C0000
+ */
+
+#define FLASH_PHYS_ADDR 0x40000000
+#define FLASH_SIZE 0x400000
+
+#define FLASH_PARTITION0_ADDR 0x00000000
+#define FLASH_PARTITION0_SIZE 0x00020000
+
+#define FLASH_PARTITION1_ADDR 0x00020000
+#define FLASH_PARTITION1_SIZE 0x000A0000
+
+#define FLASH_PARTITION2_ADDR 0x000C0000
+#define FLASH_PARTITION2_SIZE 0x00180000
+
+#define FLASH_PARTITION3_ADDR 0x00240000
+#define FLASH_PARTITION3_SIZE 0x001C0000
+
+
+static struct map_info flagadm_map = {
+		.name =		"FlagaDM flash device",
+		.size =		FLASH_SIZE,
+		.bankwidth =	2,
+};
+
+static struct mtd_partition flagadm_parts[] = {
+	{
+		.name =		"Bootloader",
+		.offset	=	FLASH_PARTITION0_ADDR,
+		.size =		FLASH_PARTITION0_SIZE
+	},
+	{
+		.name =		"Kernel image",
+		.offset =	FLASH_PARTITION1_ADDR,
+		.size =		FLASH_PARTITION1_SIZE
+	},
+	{
+		.name =		"Initial ramdisk image",
+		.offset =	FLASH_PARTITION2_ADDR,
+		.size =		FLASH_PARTITION2_SIZE
+	},
+	{
+		.name =		"Persistent storage",
+		.offset =	FLASH_PARTITION3_ADDR,
+		.size =		FLASH_PARTITION3_SIZE
+	}
+};
+
+#define PARTITION_COUNT ARRAY_SIZE(flagadm_parts)
+
+static struct mtd_info *mymtd;
+
+static int __init init_flagadm(void)
+{
+	printk(KERN_NOTICE "FlagaDM flash device: %x at %x\n",
+			FLASH_SIZE, FLASH_PHYS_ADDR);
+
+	flagadm_map.phys = FLASH_PHYS_ADDR;
+	flagadm_map.virt = ioremap(FLASH_PHYS_ADDR,
+					FLASH_SIZE);
+
+	if (!flagadm_map.virt) {
+		printk("Failed to ioremap\n");
+		return -EIO;
+	}
+
+	simple_map_init(&flagadm_map);
+
+	mymtd = do_map_probe("cfi_probe", &flagadm_map);
+	if (mymtd) {
+		mymtd->owner = THIS_MODULE;
+		mtd_device_register(mymtd, flagadm_parts, PARTITION_COUNT);
+		printk(KERN_NOTICE "FlagaDM flash device initialized\n");
+		return 0;
+	}
+
+	iounmap((void __iomem *)flagadm_map.virt);
+	return -ENXIO;
+}
+
+static void __exit cleanup_flagadm(void)
+{
+	if (mymtd) {
+		mtd_device_unregister(mymtd);
+		map_destroy(mymtd);
+	}
+	if (flagadm_map.virt) {
+		iounmap((void __iomem *)flagadm_map.virt);
+		flagadm_map.virt = NULL;
+	}
+}
+
+module_init(init_flagadm);
+module_exit(cleanup_flagadm);
+
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Kári Davíðsson <kd@flaga.is>");
+MODULE_DESCRIPTION("MTD map driver for Flaga digital module");
diff --git a/drivers/mtd/maps/ck804xrom.c b/drivers/mtd/maps/ck804xrom.c
new file mode 100644
index 000000000..0455166f0
--- /dev/null
+++ b/drivers/mtd/maps/ck804xrom.c
@@ -0,0 +1,387 @@
+/*
+ * ck804xrom.c
+ *
+ * Normal mappings of chips in physical memory
+ *
+ * Dave Olsen <dolsen@lnxi.com>
+ * Ryan Jackson <rjackson@lnxi.com>
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/flashchip.h>
+#include <linux/pci.h>
+#include <linux/pci_ids.h>
+#include <linux/list.h>
+
+
+#define MOD_NAME KBUILD_BASENAME
+
+#define ADDRESS_NAME_LEN 18
+
+#define ROM_PROBE_STEP_SIZE (64*1024)
+
+#define DEV_CK804 1
+#define DEV_MCP55 2
+
+struct ck804xrom_window {
+	void __iomem *virt;
+	unsigned long phys;
+	unsigned long size;
+	struct list_head maps;
+	struct resource rsrc;
+	struct pci_dev *pdev;
+};
+
+struct ck804xrom_map_info {
+	struct list_head list;
+	struct map_info map;
+	struct mtd_info *mtd;
+	struct resource rsrc;
+	char map_name[sizeof(MOD_NAME) + 2 + ADDRESS_NAME_LEN];
+};
+
+/*
+ * The following applies to ck804 only:
+ * The 2 bits controlling the window size are often set to allow reading
+ * the BIOS, but too small to allow writing, since the lock registers are
+ * 4MiB lower in the address space than the data.
+ *
+ * This is intended to prevent flashing the bios, perhaps accidentally.
+ *
+ * This parameter allows the normal driver to override the BIOS settings.
+ *
+ * The bits are 6 and 7.  If both bits are set, it is a 5MiB window.
+ * If only the 7 Bit is set, it is a 4MiB window.  Otherwise, a
+ * 64KiB window.
+ *
+ * The following applies to mcp55 only:
+ * The 15 bits controlling the window size are distributed as follows: 
+ * byte @0x88: bit 0..7
+ * byte @0x8c: bit 8..15
+ * word @0x90: bit 16..30
+ * If all bits are enabled, we have a 16? MiB window
+ * Please set win_size_bits to 0x7fffffff if you actually want to do something
+ */
+static uint win_size_bits = 0;
+module_param(win_size_bits, uint, 0);
+MODULE_PARM_DESC(win_size_bits, "ROM window size bits override, normally set by BIOS.");
+
+static struct ck804xrom_window ck804xrom_window = {
+	.maps = LIST_HEAD_INIT(ck804xrom_window.maps),
+};
+
+static void ck804xrom_cleanup(struct ck804xrom_window *window)
+{
+	struct ck804xrom_map_info *map, *scratch;
+	u8 byte;
+
+	if (window->pdev) {
+		/* Disable writes through the rom window */
+		pci_read_config_byte(window->pdev, 0x6d, &byte);
+		pci_write_config_byte(window->pdev, 0x6d, byte & ~1);
+	}
+
+	/* Free all of the mtd devices */
+	list_for_each_entry_safe(map, scratch, &window->maps, list) {
+		if (map->rsrc.parent)
+			release_resource(&map->rsrc);
+
+		mtd_device_unregister(map->mtd);
+		map_destroy(map->mtd);
+		list_del(&map->list);
+		kfree(map);
+	}
+	if (window->rsrc.parent)
+		release_resource(&window->rsrc);
+
+	if (window->virt) {
+		iounmap(window->virt);
+		window->virt = NULL;
+		window->phys = 0;
+		window->size = 0;
+	}
+	pci_dev_put(window->pdev);
+}
+
+
+static int ck804xrom_init_one(struct pci_dev *pdev,
+			      const struct pci_device_id *ent)
+{
+	static char *rom_probe_types[] = { "cfi_probe", "jedec_probe", NULL };
+	u8 byte;
+	u16 word;
+	struct ck804xrom_window *window = &ck804xrom_window;
+	struct ck804xrom_map_info *map = NULL;
+	unsigned long map_top;
+
+	/* Remember the pci dev I find the window in */
+	window->pdev = pci_dev_get(pdev);
+
+	switch (ent->driver_data) {
+	case DEV_CK804:
+		/* Enable the selected rom window.  This is often incorrectly
+		 * set up by the BIOS, and the 4MiB offset for the lock registers
+		 * requires the full 5MiB of window space.
+		 *
+		 * This 'write, then read' approach leaves the bits for
+		 * other uses of the hardware info.
+		 */
+		pci_read_config_byte(pdev, 0x88, &byte);
+		pci_write_config_byte(pdev, 0x88, byte | win_size_bits );
+
+		/* Assume the rom window is properly setup, and find it's size */
+		pci_read_config_byte(pdev, 0x88, &byte);
+
+		if ((byte & ((1<<7)|(1<<6))) == ((1<<7)|(1<<6)))
+			window->phys = 0xffb00000; /* 5MiB */
+		else if ((byte & (1<<7)) == (1<<7))
+			window->phys = 0xffc00000; /* 4MiB */
+		else
+			window->phys = 0xffff0000; /* 64KiB */
+		break;
+
+	case DEV_MCP55:
+		pci_read_config_byte(pdev, 0x88, &byte);
+		pci_write_config_byte(pdev, 0x88, byte | (win_size_bits & 0xff));
+
+		pci_read_config_byte(pdev, 0x8c, &byte);
+		pci_write_config_byte(pdev, 0x8c, byte | ((win_size_bits & 0xff00) >> 8));
+
+		pci_read_config_word(pdev, 0x90, &word);
+		pci_write_config_word(pdev, 0x90, word | ((win_size_bits & 0x7fff0000) >> 16));
+
+		window->phys = 0xff000000; /* 16MiB, hardcoded for now */
+		break;
+	}
+
+	window->size = 0xffffffffUL - window->phys + 1UL;
+
+	/*
+	 * Try to reserve the window mem region.  If this fails then
+	 * it is likely due to a fragment of the window being
+	 * "reserved" by the BIOS.  In the case that the
+	 * request_mem_region() fails then once the rom size is
+	 * discovered we will try to reserve the unreserved fragment.
+	 */
+	window->rsrc.name = MOD_NAME;
+	window->rsrc.start = window->phys;
+	window->rsrc.end   = window->phys + window->size - 1;
+	window->rsrc.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+	if (request_resource(&iomem_resource, &window->rsrc)) {
+		window->rsrc.parent = NULL;
+		printk(KERN_ERR MOD_NAME
+		       " %s(): Unable to register resource %pR - kernel bug?\n",
+			__func__, &window->rsrc);
+	}
+
+
+	/* Enable writes through the rom window */
+	pci_read_config_byte(pdev, 0x6d, &byte);
+	pci_write_config_byte(pdev, 0x6d, byte | 1);
+
+	/* FIXME handle registers 0x80 - 0x8C the bios region locks */
+
+	/* For write accesses caches are useless */
+	window->virt = ioremap_nocache(window->phys, window->size);
+	if (!window->virt) {
+		printk(KERN_ERR MOD_NAME ": ioremap(%08lx, %08lx) failed\n",
+			window->phys, window->size);
+		goto out;
+	}
+
+	/* Get the first address to look for a rom chip at */
+	map_top = window->phys;
+#if 1
+	/* The probe sequence run over the firmware hub lock
+	 * registers sets them to 0x7 (no access).
+	 * Probe at most the last 4MiB of the address space.
+	 */
+	if (map_top < 0xffc00000)
+		map_top = 0xffc00000;
+#endif
+	/* Loop  through and look for rom chips.  Since we don't know the
+	 * starting address for each chip, probe every ROM_PROBE_STEP_SIZE
+	 * bytes from the starting address of the window.
+	 */
+	while((map_top - 1) < 0xffffffffUL) {
+		struct cfi_private *cfi;
+		unsigned long offset;
+		int i;
+
+		if (!map)
+			map = kmalloc(sizeof(*map), GFP_KERNEL);
+
+		if (!map) {
+			printk(KERN_ERR MOD_NAME ": kmalloc failed");
+			goto out;
+		}
+		memset(map, 0, sizeof(*map));
+		INIT_LIST_HEAD(&map->list);
+		map->map.name = map->map_name;
+		map->map.phys = map_top;
+		offset = map_top - window->phys;
+		map->map.virt = (void __iomem *)
+			(((unsigned long)(window->virt)) + offset);
+		map->map.size = 0xffffffffUL - map_top + 1UL;
+		/* Set the name of the map to the address I am trying */
+		sprintf(map->map_name, "%s @%08Lx",
+			MOD_NAME, (unsigned long long)map->map.phys);
+
+		/* There is no generic VPP support */
+		for(map->map.bankwidth = 32; map->map.bankwidth;
+			map->map.bankwidth >>= 1)
+		{
+			char **probe_type;
+			/* Skip bankwidths that are not supported */
+			if (!map_bankwidth_supported(map->map.bankwidth))
+				continue;
+
+			/* Setup the map methods */
+			simple_map_init(&map->map);
+
+			/* Try all of the probe methods */
+			probe_type = rom_probe_types;
+			for(; *probe_type; probe_type++) {
+				map->mtd = do_map_probe(*probe_type, &map->map);
+				if (map->mtd)
+					goto found;
+			}
+		}
+		map_top += ROM_PROBE_STEP_SIZE;
+		continue;
+	found:
+		/* Trim the size if we are larger than the map */
+		if (map->mtd->size > map->map.size) {
+			printk(KERN_WARNING MOD_NAME
+				" rom(%llu) larger than window(%lu). fixing...\n",
+				(unsigned long long)map->mtd->size, map->map.size);
+			map->mtd->size = map->map.size;
+		}
+		if (window->rsrc.parent) {
+			/*
+			 * Registering the MTD device in iomem may not be possible
+			 * if there is a BIOS "reserved" and BUSY range.  If this
+			 * fails then continue anyway.
+			 */
+			map->rsrc.name  = map->map_name;
+			map->rsrc.start = map->map.phys;
+			map->rsrc.end   = map->map.phys + map->mtd->size - 1;
+			map->rsrc.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+			if (request_resource(&window->rsrc, &map->rsrc)) {
+				printk(KERN_ERR MOD_NAME
+					": cannot reserve MTD resource\n");
+				map->rsrc.parent = NULL;
+			}
+		}
+
+		/* Make the whole region visible in the map */
+		map->map.virt = window->virt;
+		map->map.phys = window->phys;
+		cfi = map->map.fldrv_priv;
+		for(i = 0; i < cfi->numchips; i++)
+			cfi->chips[i].start += offset;
+
+		/* Now that the mtd devices is complete claim and export it */
+		map->mtd->owner = THIS_MODULE;
+		if (mtd_device_register(map->mtd, NULL, 0)) {
+			map_destroy(map->mtd);
+			map->mtd = NULL;
+			goto out;
+		}
+
+
+		/* Calculate the new value of map_top */
+		map_top += map->mtd->size;
+
+		/* File away the map structure */
+		list_add(&map->list, &window->maps);
+		map = NULL;
+	}
+
+ out:
+	/* Free any left over map structures */
+	kfree(map);
+
+	/* See if I have any map structures */
+	if (list_empty(&window->maps)) {
+		ck804xrom_cleanup(window);
+		return -ENODEV;
+	}
+	return 0;
+}
+
+
+static void ck804xrom_remove_one(struct pci_dev *pdev)
+{
+	struct ck804xrom_window *window = &ck804xrom_window;
+
+	ck804xrom_cleanup(window);
+}
+
+static struct pci_device_id ck804xrom_pci_tbl[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, 0x0051), .driver_data = DEV_CK804 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, 0x0360), .driver_data = DEV_MCP55 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, 0x0361), .driver_data = DEV_MCP55 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, 0x0362), .driver_data = DEV_MCP55 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, 0x0363), .driver_data = DEV_MCP55 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, 0x0364), .driver_data = DEV_MCP55 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, 0x0365), .driver_data = DEV_MCP55 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, 0x0366), .driver_data = DEV_MCP55 },
+	{ PCI_DEVICE(PCI_VENDOR_ID_NVIDIA, 0x0367), .driver_data = DEV_MCP55 },
+	{ 0, }
+};
+
+#if 0
+MODULE_DEVICE_TABLE(pci, ck804xrom_pci_tbl);
+
+static struct pci_driver ck804xrom_driver = {
+	.name =		MOD_NAME,
+	.id_table =	ck804xrom_pci_tbl,
+	.probe =	ck804xrom_init_one,
+	.remove =	ck804xrom_remove_one,
+};
+#endif
+
+static int __init init_ck804xrom(void)
+{
+	struct pci_dev *pdev;
+	struct pci_device_id *id;
+	int retVal;
+	pdev = NULL;
+
+	for(id = ck804xrom_pci_tbl; id->vendor; id++) {
+		pdev = pci_get_device(id->vendor, id->device, NULL);
+		if (pdev)
+			break;
+	}
+	if (pdev) {
+		retVal = ck804xrom_init_one(pdev, id);
+		pci_dev_put(pdev);
+		return retVal;
+	}
+	return -ENXIO;
+#if 0
+	return pci_register_driver(&ck804xrom_driver);
+#endif
+}
+
+static void __exit cleanup_ck804xrom(void)
+{
+	ck804xrom_remove_one(ck804xrom_window.pdev);
+}
+
+module_init(init_ck804xrom);
+module_exit(cleanup_ck804xrom);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Eric Biederman <ebiederman@lnxi.com>, Dave Olsen <dolsen@lnxi.com>");
+MODULE_DESCRIPTION("MTD map driver for BIOS chips on the Nvidia ck804 southbridge");
+
diff --git a/drivers/mtd/maps/dc21285.c b/drivers/mtd/maps/dc21285.c
new file mode 100644
index 000000000..70a3db3ab
--- /dev/null
+++ b/drivers/mtd/maps/dc21285.c
@@ -0,0 +1,231 @@
+/*
+ * MTD map driver for flash on the DC21285 (the StrongARM-110 companion chip)
+ *
+ * (C) 2000  Nicolas Pitre <nico@fluxnic.net>
+ *
+ * This code is GPL
+ */
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/io.h>
+#include <asm/hardware/dec21285.h>
+#include <asm/mach-types.h>
+
+
+static struct mtd_info *dc21285_mtd;
+
+#ifdef CONFIG_ARCH_NETWINDER
+/*
+ * This is really ugly, but it seams to be the only
+ * realiable way to do it, as the cpld state machine
+ * is unpredictible. So we have a 25us penalty per
+ * write access.
+ */
+static void nw_en_write(void)
+{
+	unsigned long flags;
+
+	/*
+	 * we want to write a bit pattern XXX1 to Xilinx to enable
+	 * the write gate, which will be open for about the next 2ms.
+	 */
+	raw_spin_lock_irqsave(&nw_gpio_lock, flags);
+	nw_cpld_modify(CPLD_FLASH_WR_ENABLE, CPLD_FLASH_WR_ENABLE);
+	raw_spin_unlock_irqrestore(&nw_gpio_lock, flags);
+
+	/*
+	 * let the ISA bus to catch on...
+	 */
+	udelay(25);
+}
+#else
+#define nw_en_write() do { } while (0)
+#endif
+
+static map_word dc21285_read8(struct map_info *map, unsigned long ofs)
+{
+	map_word val;
+	val.x[0] = *(uint8_t*)(map->virt + ofs);
+	return val;
+}
+
+static map_word dc21285_read16(struct map_info *map, unsigned long ofs)
+{
+	map_word val;
+	val.x[0] = *(uint16_t*)(map->virt + ofs);
+	return val;
+}
+
+static map_word dc21285_read32(struct map_info *map, unsigned long ofs)
+{
+	map_word val;
+	val.x[0] = *(uint32_t*)(map->virt + ofs);
+	return val;
+}
+
+static void dc21285_copy_from(struct map_info *map, void *to, unsigned long from, ssize_t len)
+{
+	memcpy(to, (void*)(map->virt + from), len);
+}
+
+static void dc21285_write8(struct map_info *map, const map_word d, unsigned long adr)
+{
+	if (machine_is_netwinder())
+		nw_en_write();
+	*CSR_ROMWRITEREG = adr & 3;
+	adr &= ~3;
+	*(uint8_t*)(map->virt + adr) = d.x[0];
+}
+
+static void dc21285_write16(struct map_info *map, const map_word d, unsigned long adr)
+{
+	if (machine_is_netwinder())
+		nw_en_write();
+	*CSR_ROMWRITEREG = adr & 3;
+	adr &= ~3;
+	*(uint16_t*)(map->virt + adr) = d.x[0];
+}
+
+static void dc21285_write32(struct map_info *map, const map_word d, unsigned long adr)
+{
+	if (machine_is_netwinder())
+		nw_en_write();
+	*(uint32_t*)(map->virt + adr) = d.x[0];
+}
+
+static void dc21285_copy_to_32(struct map_info *map, unsigned long to, const void *from, ssize_t len)
+{
+	while (len > 0) {
+		map_word d;
+		d.x[0] = *((uint32_t*)from);
+		dc21285_write32(map, d, to);
+		from += 4;
+		to += 4;
+		len -= 4;
+	}
+}
+
+static void dc21285_copy_to_16(struct map_info *map, unsigned long to, const void *from, ssize_t len)
+{
+	while (len > 0) {
+		map_word d;
+		d.x[0] = *((uint16_t*)from);
+		dc21285_write16(map, d, to);
+		from += 2;
+		to += 2;
+		len -= 2;
+	}
+}
+
+static void dc21285_copy_to_8(struct map_info *map, unsigned long to, const void *from, ssize_t len)
+{
+	map_word d;
+	d.x[0] = *((uint8_t*)from);
+	dc21285_write8(map, d, to);
+	from++;
+	to++;
+	len--;
+}
+
+static struct map_info dc21285_map = {
+	.name = "DC21285 flash",
+	.phys = NO_XIP,
+	.size = 16*1024*1024,
+	.copy_from = dc21285_copy_from,
+};
+
+/* Partition stuff */
+static const char * const probes[] = { "RedBoot", "cmdlinepart", NULL };
+
+static int __init init_dc21285(void)
+{
+	/* Determine bankwidth */
+	switch (*CSR_SA110_CNTL & (3<<14)) {
+		case SA110_CNTL_ROMWIDTH_8:
+			dc21285_map.bankwidth = 1;
+			dc21285_map.read = dc21285_read8;
+			dc21285_map.write = dc21285_write8;
+			dc21285_map.copy_to = dc21285_copy_to_8;
+			break;
+		case SA110_CNTL_ROMWIDTH_16:
+			dc21285_map.bankwidth = 2;
+			dc21285_map.read = dc21285_read16;
+			dc21285_map.write = dc21285_write16;
+			dc21285_map.copy_to = dc21285_copy_to_16;
+			break;
+		case SA110_CNTL_ROMWIDTH_32:
+			dc21285_map.bankwidth = 4;
+			dc21285_map.read = dc21285_read32;
+			dc21285_map.write = dc21285_write32;
+			dc21285_map.copy_to = dc21285_copy_to_32;
+			break;
+		default:
+			printk (KERN_ERR "DC21285 flash: undefined bankwidth\n");
+			return -ENXIO;
+	}
+	printk (KERN_NOTICE "DC21285 flash support (%d-bit bankwidth)\n",
+		dc21285_map.bankwidth*8);
+
+	/* Let's map the flash area */
+	dc21285_map.virt = ioremap(DC21285_FLASH, 16*1024*1024);
+	if (!dc21285_map.virt) {
+		printk("Failed to ioremap\n");
+		return -EIO;
+	}
+
+	if (machine_is_ebsa285()) {
+		dc21285_mtd = do_map_probe("cfi_probe", &dc21285_map);
+	} else {
+		dc21285_mtd = do_map_probe("jedec_probe", &dc21285_map);
+	}
+
+	if (!dc21285_mtd) {
+		iounmap(dc21285_map.virt);
+		return -ENXIO;
+	}
+
+	dc21285_mtd->owner = THIS_MODULE;
+
+	mtd_device_parse_register(dc21285_mtd, probes, NULL, NULL, 0);
+
+	if(machine_is_ebsa285()) {
+		/*
+		 * Flash timing is determined with bits 19-16 of the
+		 * CSR_SA110_CNTL.  The value is the number of wait cycles, or
+		 * 0 for 16 cycles (the default).  Cycles are 20 ns.
+		 * Here we use 7 for 140 ns flash chips.
+		 */
+		/* access time */
+		*CSR_SA110_CNTL = ((*CSR_SA110_CNTL & ~0x000f0000) | (7 << 16));
+		/* burst time */
+		*CSR_SA110_CNTL = ((*CSR_SA110_CNTL & ~0x00f00000) | (7 << 20));
+		/* tristate time */
+		*CSR_SA110_CNTL = ((*CSR_SA110_CNTL & ~0x0f000000) | (7 << 24));
+	}
+
+	return 0;
+}
+
+static void __exit cleanup_dc21285(void)
+{
+	mtd_device_unregister(dc21285_mtd);
+	map_destroy(dc21285_mtd);
+	iounmap(dc21285_map.virt);
+}
+
+module_init(init_dc21285);
+module_exit(cleanup_dc21285);
+
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Nicolas Pitre <nico@fluxnic.net>");
+MODULE_DESCRIPTION("MTD map driver for DC21285 boards");
diff --git a/drivers/mtd/maps/esb2rom.c b/drivers/mtd/maps/esb2rom.c
new file mode 100644
index 000000000..f784cf0ca
--- /dev/null
+++ b/drivers/mtd/maps/esb2rom.c
@@ -0,0 +1,452 @@
+/*
+ * esb2rom.c
+ *
+ * Normal mappings of flash chips in physical memory
+ * through the Intel ESB2 Southbridge.
+ *
+ * This was derived from ichxrom.c in May 2006 by
+ *	Lew Glendenning <lglendenning@lnxi.com>
+ *
+ * Eric Biederman, of course, was a major help in this effort.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/flashchip.h>
+#include <linux/pci.h>
+#include <linux/pci_ids.h>
+#include <linux/list.h>
+
+#define MOD_NAME KBUILD_BASENAME
+
+#define ADDRESS_NAME_LEN 18
+
+#define ROM_PROBE_STEP_SIZE (64*1024) /* 64KiB */
+
+#define BIOS_CNTL		0xDC
+#define BIOS_LOCK_ENABLE	0x02
+#define BIOS_WRITE_ENABLE	0x01
+
+/* This became a 16-bit register, and EN2 has disappeared */
+#define FWH_DEC_EN1	0xD8
+#define FWH_F8_EN	0x8000
+#define FWH_F0_EN	0x4000
+#define FWH_E8_EN	0x2000
+#define FWH_E0_EN	0x1000
+#define FWH_D8_EN	0x0800
+#define FWH_D0_EN	0x0400
+#define FWH_C8_EN	0x0200
+#define FWH_C0_EN	0x0100
+#define FWH_LEGACY_F_EN	0x0080
+#define FWH_LEGACY_E_EN	0x0040
+/* reserved  0x0020 and 0x0010 */
+#define FWH_70_EN	0x0008
+#define FWH_60_EN	0x0004
+#define FWH_50_EN	0x0002
+#define FWH_40_EN	0x0001
+
+/* these are 32-bit values */
+#define FWH_SEL1	0xD0
+#define FWH_SEL2	0xD4
+
+#define FWH_8MiB	(FWH_F8_EN | FWH_F0_EN | FWH_E8_EN | FWH_E0_EN | \
+			 FWH_D8_EN | FWH_D0_EN | FWH_C8_EN | FWH_C0_EN | \
+			 FWH_70_EN | FWH_60_EN | FWH_50_EN | FWH_40_EN)
+
+#define FWH_7MiB	(FWH_F8_EN | FWH_F0_EN | FWH_E8_EN | FWH_E0_EN | \
+			 FWH_D8_EN | FWH_D0_EN | FWH_C8_EN | FWH_C0_EN | \
+			 FWH_70_EN | FWH_60_EN | FWH_50_EN)
+
+#define FWH_6MiB	(FWH_F8_EN | FWH_F0_EN | FWH_E8_EN | FWH_E0_EN | \
+			 FWH_D8_EN | FWH_D0_EN | FWH_C8_EN | FWH_C0_EN | \
+			 FWH_70_EN | FWH_60_EN)
+
+#define FWH_5MiB	(FWH_F8_EN | FWH_F0_EN | FWH_E8_EN | FWH_E0_EN | \
+			 FWH_D8_EN | FWH_D0_EN | FWH_C8_EN | FWH_C0_EN | \
+			 FWH_70_EN)
+
+#define FWH_4MiB	(FWH_F8_EN | FWH_F0_EN | FWH_E8_EN | FWH_E0_EN | \
+			 FWH_D8_EN | FWH_D0_EN | FWH_C8_EN | FWH_C0_EN)
+
+#define FWH_3_5MiB	(FWH_F8_EN | FWH_F0_EN | FWH_E8_EN | FWH_E0_EN | \
+			 FWH_D8_EN | FWH_D0_EN | FWH_C8_EN)
+
+#define FWH_3MiB	(FWH_F8_EN | FWH_F0_EN | FWH_E8_EN | FWH_E0_EN | \
+			 FWH_D8_EN | FWH_D0_EN)
+
+#define FWH_2_5MiB	(FWH_F8_EN | FWH_F0_EN | FWH_E8_EN | FWH_E0_EN | \
+			 FWH_D8_EN)
+
+#define FWH_2MiB	(FWH_F8_EN | FWH_F0_EN | FWH_E8_EN | FWH_E0_EN)
+
+#define FWH_1_5MiB	(FWH_F8_EN | FWH_F0_EN | FWH_E8_EN)
+
+#define FWH_1MiB	(FWH_F8_EN | FWH_F0_EN)
+
+#define FWH_0_5MiB	(FWH_F8_EN)
+
+
+struct esb2rom_window {
+	void __iomem* virt;
+	unsigned long phys;
+	unsigned long size;
+	struct list_head maps;
+	struct resource rsrc;
+	struct pci_dev *pdev;
+};
+
+struct esb2rom_map_info {
+	struct list_head list;
+	struct map_info map;
+	struct mtd_info *mtd;
+	struct resource rsrc;
+	char map_name[sizeof(MOD_NAME) + 2 + ADDRESS_NAME_LEN];
+};
+
+static struct esb2rom_window esb2rom_window = {
+	.maps = LIST_HEAD_INIT(esb2rom_window.maps),
+};
+
+static void esb2rom_cleanup(struct esb2rom_window *window)
+{
+	struct esb2rom_map_info *map, *scratch;
+	u8 byte;
+
+	/* Disable writes through the rom window */
+	pci_read_config_byte(window->pdev, BIOS_CNTL, &byte);
+	pci_write_config_byte(window->pdev, BIOS_CNTL,
+		byte & ~BIOS_WRITE_ENABLE);
+
+	/* Free all of the mtd devices */
+	list_for_each_entry_safe(map, scratch, &window->maps, list) {
+		if (map->rsrc.parent)
+			release_resource(&map->rsrc);
+		mtd_device_unregister(map->mtd);
+		map_destroy(map->mtd);
+		list_del(&map->list);
+		kfree(map);
+	}
+	if (window->rsrc.parent)
+		release_resource(&window->rsrc);
+	if (window->virt) {
+		iounmap(window->virt);
+		window->virt = NULL;
+		window->phys = 0;
+		window->size = 0;
+	}
+	pci_dev_put(window->pdev);
+}
+
+static int esb2rom_init_one(struct pci_dev *pdev,
+			    const struct pci_device_id *ent)
+{
+	static char *rom_probe_types[] = { "cfi_probe", "jedec_probe", NULL };
+	struct esb2rom_window *window = &esb2rom_window;
+	struct esb2rom_map_info *map = NULL;
+	unsigned long map_top;
+	u8 byte;
+	u16 word;
+
+	/* For now I just handle the ecb2 and I assume there
+	 * are not a lot of resources up at the top of the address
+	 * space.  It is possible to handle other devices in the
+	 * top 16MiB but it is very painful.  Also since
+	 * you can only really attach a FWH to an ICHX there
+	 * a number of simplifications you can make.
+	 *
+	 * Also you can page firmware hubs if an 8MiB window isn't enough
+	 * but don't currently handle that case either.
+	 */
+	window->pdev = pci_dev_get(pdev);
+
+	/* RLG:  experiment 2.  Force the window registers to the widest values */
+
+/*
+	pci_read_config_word(pdev, FWH_DEC_EN1, &word);
+	printk(KERN_DEBUG "Original FWH_DEC_EN1 : %x\n", word);
+	pci_write_config_byte(pdev, FWH_DEC_EN1, 0xff);
+	pci_read_config_byte(pdev, FWH_DEC_EN1, &byte);
+	printk(KERN_DEBUG "New FWH_DEC_EN1 : %x\n", byte);
+
+	pci_read_config_byte(pdev, FWH_DEC_EN2, &byte);
+	printk(KERN_DEBUG "Original FWH_DEC_EN2 : %x\n", byte);
+	pci_write_config_byte(pdev, FWH_DEC_EN2, 0x0f);
+	pci_read_config_byte(pdev, FWH_DEC_EN2, &byte);
+	printk(KERN_DEBUG "New FWH_DEC_EN2 : %x\n", byte);
+*/
+
+	/* Find a region continuous to the end of the ROM window  */
+	window->phys = 0;
+	pci_read_config_word(pdev, FWH_DEC_EN1, &word);
+	printk(KERN_DEBUG "pci_read_config_word : %x\n", word);
+
+	if ((word & FWH_8MiB) == FWH_8MiB)
+		window->phys = 0xff400000;
+	else if ((word & FWH_7MiB) == FWH_7MiB)
+		window->phys = 0xff500000;
+	else if ((word & FWH_6MiB) == FWH_6MiB)
+		window->phys = 0xff600000;
+	else if ((word & FWH_5MiB) == FWH_5MiB)
+		window->phys = 0xFF700000;
+	else if ((word & FWH_4MiB) == FWH_4MiB)
+		window->phys = 0xffc00000;
+	else if ((word & FWH_3_5MiB) == FWH_3_5MiB)
+		window->phys = 0xffc80000;
+	else if ((word & FWH_3MiB) == FWH_3MiB)
+		window->phys = 0xffd00000;
+	else if ((word & FWH_2_5MiB) == FWH_2_5MiB)
+		window->phys = 0xffd80000;
+	else if ((word & FWH_2MiB) == FWH_2MiB)
+		window->phys = 0xffe00000;
+	else if ((word & FWH_1_5MiB) == FWH_1_5MiB)
+		window->phys = 0xffe80000;
+	else if ((word & FWH_1MiB) == FWH_1MiB)
+		window->phys = 0xfff00000;
+	else if ((word & FWH_0_5MiB) == FWH_0_5MiB)
+		window->phys = 0xfff80000;
+
+	if (window->phys == 0) {
+		printk(KERN_ERR MOD_NAME ": Rom window is closed\n");
+		goto out;
+	}
+
+	/* reserved  0x0020 and 0x0010 */
+	window->phys -= 0x400000UL;
+	window->size = (0xffffffffUL - window->phys) + 1UL;
+
+	/* Enable writes through the rom window */
+	pci_read_config_byte(pdev, BIOS_CNTL, &byte);
+	if (!(byte & BIOS_WRITE_ENABLE)  && (byte & (BIOS_LOCK_ENABLE))) {
+		/* The BIOS will generate an error if I enable
+		 * this device, so don't even try.
+		 */
+		printk(KERN_ERR MOD_NAME ": firmware access control, I can't enable writes\n");
+		goto out;
+	}
+	pci_write_config_byte(pdev, BIOS_CNTL, byte | BIOS_WRITE_ENABLE);
+
+	/*
+	 * Try to reserve the window mem region.  If this fails then
+	 * it is likely due to the window being "reseved" by the BIOS.
+	 */
+	window->rsrc.name = MOD_NAME;
+	window->rsrc.start = window->phys;
+	window->rsrc.end   = window->phys + window->size - 1;
+	window->rsrc.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+	if (request_resource(&iomem_resource, &window->rsrc)) {
+		window->rsrc.parent = NULL;
+		printk(KERN_DEBUG MOD_NAME ": "
+		       "%s(): Unable to register resource %pR - kernel bug?\n",
+			__func__, &window->rsrc);
+	}
+
+	/* Map the firmware hub into my address space. */
+	window->virt = ioremap_nocache(window->phys, window->size);
+	if (!window->virt) {
+		printk(KERN_ERR MOD_NAME ": ioremap(%08lx, %08lx) failed\n",
+			window->phys, window->size);
+		goto out;
+	}
+
+	/* Get the first address to look for an rom chip at */
+	map_top = window->phys;
+	if ((window->phys & 0x3fffff) != 0) {
+		/* if not aligned on 4MiB, look 4MiB lower in address space */
+		map_top = window->phys + 0x400000;
+	}
+#if 1
+	/* The probe sequence run over the firmware hub lock
+	 * registers sets them to 0x7 (no access).
+	 * (Insane hardware design, but most copied Intel's.)
+	 * ==> Probe at most the last 4M of the address space.
+	 */
+	if (map_top < 0xffc00000)
+		map_top = 0xffc00000;
+#endif
+	/* Loop through and look for rom chips */
+	while ((map_top - 1) < 0xffffffffUL) {
+		struct cfi_private *cfi;
+		unsigned long offset;
+		int i;
+
+		if (!map)
+			map = kmalloc(sizeof(*map), GFP_KERNEL);
+		if (!map) {
+			printk(KERN_ERR MOD_NAME ": kmalloc failed");
+			goto out;
+		}
+		memset(map, 0, sizeof(*map));
+		INIT_LIST_HEAD(&map->list);
+		map->map.name = map->map_name;
+		map->map.phys = map_top;
+		offset = map_top - window->phys;
+		map->map.virt = (void __iomem *)
+			(((unsigned long)(window->virt)) + offset);
+		map->map.size = 0xffffffffUL - map_top + 1UL;
+		/* Set the name of the map to the address I am trying */
+		sprintf(map->map_name, "%s @%08Lx",
+			MOD_NAME, (unsigned long long)map->map.phys);
+
+		/* Firmware hubs only use vpp when being programmed
+		 * in a factory setting.  So in-place programming
+		 * needs to use a different method.
+		 */
+		for(map->map.bankwidth = 32; map->map.bankwidth;
+			map->map.bankwidth >>= 1) {
+			char **probe_type;
+			/* Skip bankwidths that are not supported */
+			if (!map_bankwidth_supported(map->map.bankwidth))
+				continue;
+
+			/* Setup the map methods */
+			simple_map_init(&map->map);
+
+			/* Try all of the probe methods */
+			probe_type = rom_probe_types;
+			for(; *probe_type; probe_type++) {
+				map->mtd = do_map_probe(*probe_type, &map->map);
+				if (map->mtd)
+					goto found;
+			}
+		}
+		map_top += ROM_PROBE_STEP_SIZE;
+		continue;
+	found:
+		/* Trim the size if we are larger than the map */
+		if (map->mtd->size > map->map.size) {
+			printk(KERN_WARNING MOD_NAME
+				" rom(%llu) larger than window(%lu). fixing...\n",
+				(unsigned long long)map->mtd->size, map->map.size);
+			map->mtd->size = map->map.size;
+		}
+		if (window->rsrc.parent) {
+			/*
+			 * Registering the MTD device in iomem may not be possible
+			 * if there is a BIOS "reserved" and BUSY range.  If this
+			 * fails then continue anyway.
+			 */
+			map->rsrc.name  = map->map_name;
+			map->rsrc.start = map->map.phys;
+			map->rsrc.end   = map->map.phys + map->mtd->size - 1;
+			map->rsrc.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+			if (request_resource(&window->rsrc, &map->rsrc)) {
+				printk(KERN_ERR MOD_NAME
+					": cannot reserve MTD resource\n");
+				map->rsrc.parent = NULL;
+			}
+		}
+
+		/* Make the whole region visible in the map */
+		map->map.virt = window->virt;
+		map->map.phys = window->phys;
+		cfi = map->map.fldrv_priv;
+		for(i = 0; i < cfi->numchips; i++)
+			cfi->chips[i].start += offset;
+
+		/* Now that the mtd devices is complete claim and export it */
+		map->mtd->owner = THIS_MODULE;
+		if (mtd_device_register(map->mtd, NULL, 0)) {
+			map_destroy(map->mtd);
+			map->mtd = NULL;
+			goto out;
+		}
+
+		/* Calculate the new value of map_top */
+		map_top += map->mtd->size;
+
+		/* File away the map structure */
+		list_add(&map->list, &window->maps);
+		map = NULL;
+	}
+
+ out:
+	/* Free any left over map structures */
+	kfree(map);
+
+	/* See if I have any map structures */
+	if (list_empty(&window->maps)) {
+		esb2rom_cleanup(window);
+		return -ENODEV;
+	}
+	return 0;
+}
+
+static void esb2rom_remove_one(struct pci_dev *pdev)
+{
+	struct esb2rom_window *window = &esb2rom_window;
+	esb2rom_cleanup(window);
+}
+
+static struct pci_device_id esb2rom_pci_tbl[] = {
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB2_0,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ 0, },
+};
+
+#if 0
+MODULE_DEVICE_TABLE(pci, esb2rom_pci_tbl);
+
+static struct pci_driver esb2rom_driver = {
+	.name =		MOD_NAME,
+	.id_table =	esb2rom_pci_tbl,
+	.probe =	esb2rom_init_one,
+	.remove =	esb2rom_remove_one,
+};
+#endif
+
+static int __init init_esb2rom(void)
+{
+	struct pci_dev *pdev;
+	struct pci_device_id *id;
+	int retVal;
+
+	pdev = NULL;
+	for (id = esb2rom_pci_tbl; id->vendor; id++) {
+		printk(KERN_DEBUG "device id = %x\n", id->device);
+		pdev = pci_get_device(id->vendor, id->device, NULL);
+		if (pdev) {
+			printk(KERN_DEBUG "matched device = %x\n", id->device);
+			break;
+		}
+	}
+	if (pdev) {
+		printk(KERN_DEBUG "matched device id %x\n", id->device);
+		retVal = esb2rom_init_one(pdev, &esb2rom_pci_tbl[0]);
+		pci_dev_put(pdev);
+		printk(KERN_DEBUG "retVal = %d\n", retVal);
+		return retVal;
+	}
+	return -ENXIO;
+#if 0
+	return pci_register_driver(&esb2rom_driver);
+#endif
+}
+
+static void __exit cleanup_esb2rom(void)
+{
+	esb2rom_remove_one(esb2rom_window.pdev);
+}
+
+module_init(init_esb2rom);
+module_exit(cleanup_esb2rom);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Lew Glendenning <lglendenning@lnxi.com>");
+MODULE_DESCRIPTION("MTD map driver for BIOS chips on the ESB2 southbridge");
diff --git a/drivers/mtd/maps/gpio-addr-flash.c b/drivers/mtd/maps/gpio-addr-flash.c
new file mode 100644
index 000000000..2fb346091
--- /dev/null
+++ b/drivers/mtd/maps/gpio-addr-flash.c
@@ -0,0 +1,302 @@
+/*
+ * drivers/mtd/maps/gpio-addr-flash.c
+ *
+ * Handle the case where a flash device is mostly addressed using physical
+ * line and supplemented by GPIOs.  This way you can hook up say a 8MiB flash
+ * to a 2MiB memory range and use the GPIOs to select a particular range.
+ *
+ * Copyright © 2000 Nicolas Pitre <nico@cam.org>
+ * Copyright © 2005-2009 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/gpio.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#define pr_devinit(fmt, args...) \
+	({ static const char __fmt[] = fmt; printk(__fmt, ## args); })
+
+#define DRIVER_NAME "gpio-addr-flash"
+#define PFX DRIVER_NAME ": "
+
+/**
+ * struct async_state - keep GPIO flash state
+ *	@mtd:         MTD state for this mapping
+ *	@map:         MTD map state for this flash
+ *	@gpio_count:  number of GPIOs used to address
+ *	@gpio_addrs:  array of GPIOs to twiddle
+ *	@gpio_values: cached GPIO values
+ *	@win_size:    dedicated memory size (if no GPIOs)
+ */
+struct async_state {
+	struct mtd_info *mtd;
+	struct map_info map;
+	size_t gpio_count;
+	unsigned *gpio_addrs;
+	int *gpio_values;
+	unsigned long win_size;
+};
+#define gf_map_info_to_state(mi) ((struct async_state *)(mi)->map_priv_1)
+
+/**
+ * gf_set_gpios() - set GPIO address lines to access specified flash offset
+ *	@state: GPIO flash state
+ *	@ofs:   desired offset to access
+ *
+ * Rather than call the GPIO framework every time, cache the last-programmed
+ * value.  This speeds up sequential accesses (which are by far the most common
+ * type).  We rely on the GPIO framework to treat non-zero value as high so
+ * that we don't have to normalize the bits.
+ */
+static void gf_set_gpios(struct async_state *state, unsigned long ofs)
+{
+	size_t i = 0;
+	int value;
+	ofs /= state->win_size;
+	do {
+		value = ofs & (1 << i);
+		if (state->gpio_values[i] != value) {
+			gpio_set_value(state->gpio_addrs[i], value);
+			state->gpio_values[i] = value;
+		}
+	} while (++i < state->gpio_count);
+}
+
+/**
+ * gf_read() - read a word at the specified offset
+ *	@map: MTD map state
+ *	@ofs: desired offset to read
+ */
+static map_word gf_read(struct map_info *map, unsigned long ofs)
+{
+	struct async_state *state = gf_map_info_to_state(map);
+	uint16_t word;
+	map_word test;
+
+	gf_set_gpios(state, ofs);
+
+	word = readw(map->virt + (ofs % state->win_size));
+	test.x[0] = word;
+	return test;
+}
+
+/**
+ * gf_copy_from() - copy a chunk of data from the flash
+ *	@map:  MTD map state
+ *	@to:   memory to copy to
+ *	@from: flash offset to copy from
+ *	@len:  how much to copy
+ *
+ * The "from" region may straddle more than one window, so toggle the GPIOs for
+ * each window region before reading its data.
+ */
+static void gf_copy_from(struct map_info *map, void *to, unsigned long from, ssize_t len)
+{
+	struct async_state *state = gf_map_info_to_state(map);
+
+	int this_len;
+
+	while (len) {
+		if ((from % state->win_size) + len > state->win_size)
+			this_len = state->win_size - (from % state->win_size);
+		else
+			this_len = len;
+
+		gf_set_gpios(state, from);
+		memcpy_fromio(to, map->virt + (from % state->win_size),
+			 this_len);
+		len -= this_len;
+		from += this_len;
+		to += this_len;
+	}
+}
+
+/**
+ * gf_write() - write a word at the specified offset
+ *	@map: MTD map state
+ *	@ofs: desired offset to write
+ */
+static void gf_write(struct map_info *map, map_word d1, unsigned long ofs)
+{
+	struct async_state *state = gf_map_info_to_state(map);
+	uint16_t d;
+
+	gf_set_gpios(state, ofs);
+
+	d = d1.x[0];
+	writew(d, map->virt + (ofs % state->win_size));
+}
+
+/**
+ * gf_copy_to() - copy a chunk of data to the flash
+ *	@map:  MTD map state
+ *	@to:   flash offset to copy to
+ *	@from: memory to copy from
+ *	@len:  how much to copy
+ *
+ * See gf_copy_from() caveat.
+ */
+static void gf_copy_to(struct map_info *map, unsigned long to,
+		       const void *from, ssize_t len)
+{
+	struct async_state *state = gf_map_info_to_state(map);
+
+	int this_len;
+
+	while (len) {
+		if ((to % state->win_size) + len > state->win_size)
+			this_len = state->win_size - (to % state->win_size);
+		else
+			this_len = len;
+
+		gf_set_gpios(state, to);
+		memcpy_toio(map->virt + (to % state->win_size), from, len);
+
+		len -= this_len;
+		to += this_len;
+		from += this_len;
+	}
+}
+
+static const char * const part_probe_types[] = {
+	"cmdlinepart", "RedBoot", NULL };
+
+/**
+ * gpio_flash_probe() - setup a mapping for a GPIO assisted flash
+ *	@pdev: platform device
+ *
+ * The platform resource layout expected looks something like:
+ * struct mtd_partition partitions[] = { ... };
+ * struct physmap_flash_data flash_data = { ... };
+ * unsigned flash_gpios[] = { GPIO_XX, GPIO_XX, ... };
+ * struct resource flash_resource[] = {
+ *	{
+ *		.name  = "cfi_probe",
+ *		.start = 0x20000000,
+ *		.end   = 0x201fffff,
+ *		.flags = IORESOURCE_MEM,
+ *	}, {
+ *		.start = (unsigned long)flash_gpios,
+ *		.end   = ARRAY_SIZE(flash_gpios),
+ *		.flags = IORESOURCE_IRQ,
+ *	}
+ * };
+ * struct platform_device flash_device = {
+ *	.name          = "gpio-addr-flash",
+ *	.dev           = { .platform_data = &flash_data, },
+ *	.num_resources = ARRAY_SIZE(flash_resource),
+ *	.resource      = flash_resource,
+ *	...
+ * };
+ */
+static int gpio_flash_probe(struct platform_device *pdev)
+{
+	size_t i, arr_size;
+	struct physmap_flash_data *pdata;
+	struct resource *memory;
+	struct resource *gpios;
+	struct async_state *state;
+
+	pdata = dev_get_platdata(&pdev->dev);
+	memory = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	gpios = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+
+	if (!memory || !gpios || !gpios->end)
+		return -EINVAL;
+
+	arr_size = sizeof(int) * gpios->end;
+	state = kzalloc(sizeof(*state) + arr_size, GFP_KERNEL);
+	if (!state)
+		return -ENOMEM;
+
+	/*
+	 * We cast start/end to known types in the boards file, so cast
+	 * away their pointer types here to the known types (gpios->xxx).
+	 */
+	state->gpio_count     = gpios->end;
+	state->gpio_addrs     = (void *)(unsigned long)gpios->start;
+	state->gpio_values    = (void *)(state + 1);
+	state->win_size       = resource_size(memory);
+	memset(state->gpio_values, 0xff, arr_size);
+
+	state->map.name       = DRIVER_NAME;
+	state->map.read       = gf_read;
+	state->map.copy_from  = gf_copy_from;
+	state->map.write      = gf_write;
+	state->map.copy_to    = gf_copy_to;
+	state->map.bankwidth  = pdata->width;
+	state->map.size       = state->win_size * (1 << state->gpio_count);
+	state->map.virt       = ioremap_nocache(memory->start, state->map.size);
+	state->map.phys       = NO_XIP;
+	state->map.map_priv_1 = (unsigned long)state;
+
+	platform_set_drvdata(pdev, state);
+
+	i = 0;
+	do {
+		if (gpio_request(state->gpio_addrs[i], DRIVER_NAME)) {
+			pr_devinit(KERN_ERR PFX "failed to request gpio %d\n",
+				state->gpio_addrs[i]);
+			while (i--)
+				gpio_free(state->gpio_addrs[i]);
+			kfree(state);
+			return -EBUSY;
+		}
+		gpio_direction_output(state->gpio_addrs[i], 0);
+	} while (++i < state->gpio_count);
+
+	pr_devinit(KERN_NOTICE PFX "probing %d-bit flash bus\n",
+		state->map.bankwidth * 8);
+	state->mtd = do_map_probe(memory->name, &state->map);
+	if (!state->mtd) {
+		for (i = 0; i < state->gpio_count; ++i)
+			gpio_free(state->gpio_addrs[i]);
+		kfree(state);
+		return -ENXIO;
+	}
+
+
+	mtd_device_parse_register(state->mtd, part_probe_types, NULL,
+				  pdata->parts, pdata->nr_parts);
+
+	return 0;
+}
+
+static int gpio_flash_remove(struct platform_device *pdev)
+{
+	struct async_state *state = platform_get_drvdata(pdev);
+	size_t i = 0;
+	do {
+		gpio_free(state->gpio_addrs[i]);
+	} while (++i < state->gpio_count);
+	mtd_device_unregister(state->mtd);
+	map_destroy(state->mtd);
+	kfree(state);
+	return 0;
+}
+
+static struct platform_driver gpio_flash_driver = {
+	.probe		= gpio_flash_probe,
+	.remove		= gpio_flash_remove,
+	.driver		= {
+		.name	= DRIVER_NAME,
+	},
+};
+
+module_platform_driver(gpio_flash_driver);
+
+MODULE_AUTHOR("Mike Frysinger <vapier@gentoo.org>");
+MODULE_DESCRIPTION("MTD map driver for flashes addressed physically and with gpios");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mtd/maps/ichxrom.c b/drivers/mtd/maps/ichxrom.c
new file mode 100644
index 000000000..c7478e18f
--- /dev/null
+++ b/drivers/mtd/maps/ichxrom.c
@@ -0,0 +1,380 @@
+/*
+ * ichxrom.c
+ *
+ * Normal mappings of chips in physical memory
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/flashchip.h>
+#include <linux/pci.h>
+#include <linux/pci_ids.h>
+#include <linux/list.h>
+
+#define xstr(s) str(s)
+#define str(s) #s
+#define MOD_NAME xstr(KBUILD_BASENAME)
+
+#define ADDRESS_NAME_LEN 18
+
+#define ROM_PROBE_STEP_SIZE (64*1024) /* 64KiB */
+
+#define BIOS_CNTL	0x4e
+#define FWH_DEC_EN1	0xE3
+#define FWH_DEC_EN2	0xF0
+#define FWH_SEL1	0xE8
+#define FWH_SEL2	0xEE
+
+struct ichxrom_window {
+	void __iomem* virt;
+	unsigned long phys;
+	unsigned long size;
+	struct list_head maps;
+	struct resource rsrc;
+	struct pci_dev *pdev;
+};
+
+struct ichxrom_map_info {
+	struct list_head list;
+	struct map_info map;
+	struct mtd_info *mtd;
+	struct resource rsrc;
+	char map_name[sizeof(MOD_NAME) + 2 + ADDRESS_NAME_LEN];
+};
+
+static struct ichxrom_window ichxrom_window = {
+	.maps = LIST_HEAD_INIT(ichxrom_window.maps),
+};
+
+static void ichxrom_cleanup(struct ichxrom_window *window)
+{
+	struct ichxrom_map_info *map, *scratch;
+	u16 word;
+
+	/* Disable writes through the rom window */
+	pci_read_config_word(window->pdev, BIOS_CNTL, &word);
+	pci_write_config_word(window->pdev, BIOS_CNTL, word & ~1);
+	pci_dev_put(window->pdev);
+
+	/* Free all of the mtd devices */
+	list_for_each_entry_safe(map, scratch, &window->maps, list) {
+		if (map->rsrc.parent)
+			release_resource(&map->rsrc);
+		mtd_device_unregister(map->mtd);
+		map_destroy(map->mtd);
+		list_del(&map->list);
+		kfree(map);
+	}
+	if (window->rsrc.parent)
+		release_resource(&window->rsrc);
+	if (window->virt) {
+		iounmap(window->virt);
+		window->virt = NULL;
+		window->phys = 0;
+		window->size = 0;
+		window->pdev = NULL;
+	}
+}
+
+
+static int ichxrom_init_one(struct pci_dev *pdev,
+			    const struct pci_device_id *ent)
+{
+	static char *rom_probe_types[] = { "cfi_probe", "jedec_probe", NULL };
+	struct ichxrom_window *window = &ichxrom_window;
+	struct ichxrom_map_info *map = NULL;
+	unsigned long map_top;
+	u8 byte;
+	u16 word;
+
+	/* For now I just handle the ichx and I assume there
+	 * are not a lot of resources up at the top of the address
+	 * space.  It is possible to handle other devices in the
+	 * top 16MB but it is very painful.  Also since
+	 * you can only really attach a FWH to an ICHX there
+	 * a number of simplifications you can make.
+	 *
+	 * Also you can page firmware hubs if an 8MB window isn't enough
+	 * but don't currently handle that case either.
+	 */
+	window->pdev = pdev;
+
+	/* Find a region continuous to the end of the ROM window  */
+	window->phys = 0;
+	pci_read_config_byte(pdev, FWH_DEC_EN1, &byte);
+	if (byte == 0xff) {
+		window->phys = 0xffc00000;
+		pci_read_config_byte(pdev, FWH_DEC_EN2, &byte);
+		if ((byte & 0x0f) == 0x0f) {
+			window->phys = 0xff400000;
+		}
+		else if ((byte & 0x0e) == 0x0e) {
+			window->phys = 0xff500000;
+		}
+		else if ((byte & 0x0c) == 0x0c) {
+			window->phys = 0xff600000;
+		}
+		else if ((byte & 0x08) == 0x08) {
+			window->phys = 0xff700000;
+		}
+	}
+	else if ((byte & 0xfe) == 0xfe) {
+		window->phys = 0xffc80000;
+	}
+	else if ((byte & 0xfc) == 0xfc) {
+		window->phys = 0xffd00000;
+	}
+	else if ((byte & 0xf8) == 0xf8) {
+		window->phys = 0xffd80000;
+	}
+	else if ((byte & 0xf0) == 0xf0) {
+		window->phys = 0xffe00000;
+	}
+	else if ((byte & 0xe0) == 0xe0) {
+		window->phys = 0xffe80000;
+	}
+	else if ((byte & 0xc0) == 0xc0) {
+		window->phys = 0xfff00000;
+	}
+	else if ((byte & 0x80) == 0x80) {
+		window->phys = 0xfff80000;
+	}
+
+	if (window->phys == 0) {
+		printk(KERN_ERR MOD_NAME ": Rom window is closed\n");
+		goto out;
+	}
+	window->phys -= 0x400000UL;
+	window->size = (0xffffffffUL - window->phys) + 1UL;
+
+	/* Enable writes through the rom window */
+	pci_read_config_word(pdev, BIOS_CNTL, &word);
+	if (!(word & 1)  && (word & (1<<1))) {
+		/* The BIOS will generate an error if I enable
+		 * this device, so don't even try.
+		 */
+		printk(KERN_ERR MOD_NAME ": firmware access control, I can't enable writes\n");
+		goto out;
+	}
+	pci_write_config_word(pdev, BIOS_CNTL, word | 1);
+
+	/*
+	 * Try to reserve the window mem region.  If this fails then
+	 * it is likely due to the window being "reseved" by the BIOS.
+	 */
+	window->rsrc.name = MOD_NAME;
+	window->rsrc.start = window->phys;
+	window->rsrc.end   = window->phys + window->size - 1;
+	window->rsrc.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+	if (request_resource(&iomem_resource, &window->rsrc)) {
+		window->rsrc.parent = NULL;
+		printk(KERN_DEBUG MOD_NAME ": "
+		       "%s(): Unable to register resource %pR - kernel bug?\n",
+		       __func__, &window->rsrc);
+	}
+
+	/* Map the firmware hub into my address space. */
+	window->virt = ioremap_nocache(window->phys, window->size);
+	if (!window->virt) {
+		printk(KERN_ERR MOD_NAME ": ioremap(%08lx, %08lx) failed\n",
+			window->phys, window->size);
+		goto out;
+	}
+
+	/* Get the first address to look for an rom chip at */
+	map_top = window->phys;
+	if ((window->phys & 0x3fffff) != 0) {
+		map_top = window->phys + 0x400000;
+	}
+#if 1
+	/* The probe sequence run over the firmware hub lock
+	 * registers sets them to 0x7 (no access).
+	 * Probe at most the last 4M of the address space.
+	 */
+	if (map_top < 0xffc00000) {
+		map_top = 0xffc00000;
+	}
+#endif
+	/* Loop through and look for rom chips */
+	while((map_top - 1) < 0xffffffffUL) {
+		struct cfi_private *cfi;
+		unsigned long offset;
+		int i;
+
+		if (!map) {
+			map = kmalloc(sizeof(*map), GFP_KERNEL);
+		}
+		if (!map) {
+			printk(KERN_ERR MOD_NAME ": kmalloc failed");
+			goto out;
+		}
+		memset(map, 0, sizeof(*map));
+		INIT_LIST_HEAD(&map->list);
+		map->map.name = map->map_name;
+		map->map.phys = map_top;
+		offset = map_top - window->phys;
+		map->map.virt = (void __iomem *)
+			(((unsigned long)(window->virt)) + offset);
+		map->map.size = 0xffffffffUL - map_top + 1UL;
+		/* Set the name of the map to the address I am trying */
+		sprintf(map->map_name, "%s @%08Lx",
+			MOD_NAME, (unsigned long long)map->map.phys);
+
+		/* Firmware hubs only use vpp when being programmed
+		 * in a factory setting.  So in-place programming
+		 * needs to use a different method.
+		 */
+		for(map->map.bankwidth = 32; map->map.bankwidth;
+			map->map.bankwidth >>= 1)
+		{
+			char **probe_type;
+			/* Skip bankwidths that are not supported */
+			if (!map_bankwidth_supported(map->map.bankwidth))
+				continue;
+
+			/* Setup the map methods */
+			simple_map_init(&map->map);
+
+			/* Try all of the probe methods */
+			probe_type = rom_probe_types;
+			for(; *probe_type; probe_type++) {
+				map->mtd = do_map_probe(*probe_type, &map->map);
+				if (map->mtd)
+					goto found;
+			}
+		}
+		map_top += ROM_PROBE_STEP_SIZE;
+		continue;
+	found:
+		/* Trim the size if we are larger than the map */
+		if (map->mtd->size > map->map.size) {
+			printk(KERN_WARNING MOD_NAME
+				" rom(%llu) larger than window(%lu). fixing...\n",
+				(unsigned long long)map->mtd->size, map->map.size);
+			map->mtd->size = map->map.size;
+		}
+		if (window->rsrc.parent) {
+			/*
+			 * Registering the MTD device in iomem may not be possible
+			 * if there is a BIOS "reserved" and BUSY range.  If this
+			 * fails then continue anyway.
+			 */
+			map->rsrc.name  = map->map_name;
+			map->rsrc.start = map->map.phys;
+			map->rsrc.end   = map->map.phys + map->mtd->size - 1;
+			map->rsrc.flags = IORESOURCE_MEM | IORESOURCE_BUSY;
+			if (request_resource(&window->rsrc, &map->rsrc)) {
+				printk(KERN_ERR MOD_NAME
+					": cannot reserve MTD resource\n");
+				map->rsrc.parent = NULL;
+			}
+		}
+
+		/* Make the whole region visible in the map */
+		map->map.virt = window->virt;
+		map->map.phys = window->phys;
+		cfi = map->map.fldrv_priv;
+		for(i = 0; i < cfi->numchips; i++) {
+			cfi->chips[i].start += offset;
+		}
+
+		/* Now that the mtd devices is complete claim and export it */
+		map->mtd->owner = THIS_MODULE;
+		if (mtd_device_register(map->mtd, NULL, 0)) {
+			map_destroy(map->mtd);
+			map->mtd = NULL;
+			goto out;
+		}
+
+
+		/* Calculate the new value of map_top */
+		map_top += map->mtd->size;
+
+		/* File away the map structure */
+		list_add(&map->list, &window->maps);
+		map = NULL;
+	}
+
+ out:
+	/* Free any left over map structures */
+	kfree(map);
+
+	/* See if I have any map structures */
+	if (list_empty(&window->maps)) {
+		ichxrom_cleanup(window);
+		return -ENODEV;
+	}
+	return 0;
+}
+
+
+static void ichxrom_remove_one(struct pci_dev *pdev)
+{
+	struct ichxrom_window *window = &ichxrom_window;
+	ichxrom_cleanup(window);
+}
+
+static struct pci_device_id ichxrom_pci_tbl[] = {
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_0,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_0,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801DB_0,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801EB_0,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ESB_1,
+	  PCI_ANY_ID, PCI_ANY_ID, },
+	{ 0, },
+};
+
+#if 0
+MODULE_DEVICE_TABLE(pci, ichxrom_pci_tbl);
+
+static struct pci_driver ichxrom_driver = {
+	.name =		MOD_NAME,
+	.id_table =	ichxrom_pci_tbl,
+	.probe =	ichxrom_init_one,
+	.remove =	ichxrom_remove_one,
+};
+#endif
+
+static int __init init_ichxrom(void)
+{
+	struct pci_dev *pdev;
+	struct pci_device_id *id;
+
+	pdev = NULL;
+	for (id = ichxrom_pci_tbl; id->vendor; id++) {
+		pdev = pci_get_device(id->vendor, id->device, NULL);
+		if (pdev) {
+			break;
+		}
+	}
+	if (pdev) {
+		return ichxrom_init_one(pdev, &ichxrom_pci_tbl[0]);
+	}
+	return -ENXIO;
+#if 0
+	return pci_register_driver(&ichxrom_driver);
+#endif
+}
+
+static void __exit cleanup_ichxrom(void)
+{
+	ichxrom_remove_one(ichxrom_window.pdev);
+}
+
+module_init(init_ichxrom);
+module_exit(cleanup_ichxrom);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Eric Biederman <ebiederman@lnxi.com>");
+MODULE_DESCRIPTION("MTD map driver for BIOS chips on the ICHX southbridge");
diff --git a/drivers/mtd/maps/impa7.c b/drivers/mtd/maps/impa7.c
new file mode 100644
index 000000000..15bbda03b
--- /dev/null
+++ b/drivers/mtd/maps/impa7.c
@@ -0,0 +1,119 @@
+/*
+ * Handle mapping of the NOR flash on implementa A7 boards
+ *
+ * Copyright 2002 SYSGO Real-Time Solutions GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+#define WINDOW_ADDR0 0x00000000      /* physical properties of flash */
+#define WINDOW_SIZE0 0x00800000
+#define WINDOW_ADDR1 0x10000000      /* physical properties of flash */
+#define WINDOW_SIZE1 0x00800000
+#define NUM_FLASHBANKS 2
+#define BUSWIDTH     4
+
+#define MSG_PREFIX "impA7:"   /* prefix for our printk()'s */
+#define MTDID      "impa7-%d"  /* for mtdparts= partitioning */
+
+static struct mtd_info *impa7_mtd[NUM_FLASHBANKS];
+
+static const char * const rom_probe_types[] = { "jedec_probe", NULL };
+
+static struct map_info impa7_map[NUM_FLASHBANKS] = {
+	{
+		.name = "impA7 NOR Flash Bank #0",
+		.size = WINDOW_SIZE0,
+		.bankwidth = BUSWIDTH,
+	},
+	{
+		.name = "impA7 NOR Flash Bank #1",
+		.size = WINDOW_SIZE1,
+		.bankwidth = BUSWIDTH,
+	},
+};
+
+/*
+ * MTD partitioning stuff
+ */
+static struct mtd_partition partitions[] =
+{
+	{
+		.name = "FileSystem",
+		.size = 0x800000,
+		.offset = 0x00000000
+	},
+};
+
+static int __init init_impa7(void)
+{
+	const char * const *type;
+	int i;
+	static struct { u_long addr; u_long size; } pt[NUM_FLASHBANKS] = {
+	  { WINDOW_ADDR0, WINDOW_SIZE0 },
+	  { WINDOW_ADDR1, WINDOW_SIZE1 },
+        };
+	int devicesfound = 0;
+
+	for(i=0; i<NUM_FLASHBANKS; i++)
+	{
+		printk(KERN_NOTICE MSG_PREFIX "probing 0x%08lx at 0x%08lx\n",
+		       pt[i].size, pt[i].addr);
+
+		impa7_map[i].phys = pt[i].addr;
+		impa7_map[i].virt = ioremap(pt[i].addr, pt[i].size);
+		if (!impa7_map[i].virt) {
+			printk(MSG_PREFIX "failed to ioremap\n");
+			return -EIO;
+		}
+		simple_map_init(&impa7_map[i]);
+
+		impa7_mtd[i] = NULL;
+		type = rom_probe_types;
+		for(; !impa7_mtd[i] && *type; type++) {
+			impa7_mtd[i] = do_map_probe(*type, &impa7_map[i]);
+		}
+
+		if (impa7_mtd[i]) {
+			impa7_mtd[i]->owner = THIS_MODULE;
+			devicesfound++;
+			mtd_device_parse_register(impa7_mtd[i], NULL, NULL,
+						  partitions,
+						  ARRAY_SIZE(partitions));
+		} else {
+			iounmap((void __iomem *)impa7_map[i].virt);
+		}
+	}
+	return devicesfound == 0 ? -ENXIO : 0;
+}
+
+static void __exit cleanup_impa7(void)
+{
+	int i;
+	for (i=0; i<NUM_FLASHBANKS; i++) {
+		if (impa7_mtd[i]) {
+			mtd_device_unregister(impa7_mtd[i]);
+			map_destroy(impa7_mtd[i]);
+			iounmap((void __iomem *)impa7_map[i].virt);
+			impa7_map[i].virt = NULL;
+		}
+	}
+}
+
+module_init(init_impa7);
+module_exit(cleanup_impa7);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Pavel Bartusek <pba@sysgo.de>");
+MODULE_DESCRIPTION("MTD map driver for implementa impA7");
diff --git a/drivers/mtd/maps/intel_vr_nor.c b/drivers/mtd/maps/intel_vr_nor.c
new file mode 100644
index 000000000..5ab71f0e1
--- /dev/null
+++ b/drivers/mtd/maps/intel_vr_nor.c
@@ -0,0 +1,265 @@
+/*
+ * drivers/mtd/maps/intel_vr_nor.c
+ *
+ * An MTD map driver for a NOR flash bank on the Expansion Bus of the Intel
+ * Vermilion Range chipset.
+ *
+ * The Vermilion Range Expansion Bus supports four chip selects, each of which
+ * has 64MiB of address space.  The 2nd BAR of the Expansion Bus PCI Device
+ * is a 256MiB memory region containing the address spaces for all four of the
+ * chip selects, with start addresses hardcoded on 64MiB boundaries.
+ *
+ * This map driver only supports NOR flash on chip select 0.  The buswidth
+ * (either 8 bits or 16 bits) is determined by reading the Expansion Bus Timing
+ * and Control Register for Chip Select 0 (EXP_TIMING_CS0).  This driver does
+ * not modify the value in the EXP_TIMING_CS0 register except to enable writing
+ * and disable boot acceleration.  The timing parameters in the register are
+ * assumed to have been properly initialized by the BIOS.  The reset default
+ * timing parameters are maximally conservative (slow), so access to the flash
+ * will be slower than it should be if the BIOS has not initialized the timing
+ * parameters.
+ *
+ * Author: Andy Lowe <alowe@mvista.com>
+ *
+ * 2006 (c) MontaVista Software, Inc. This file is licensed under
+ * the terms of the GNU General Public License version 2. This program
+ * is licensed "as is" without any warranty of any kind, whether express
+ * or implied.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/pci.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/cfi.h>
+#include <linux/mtd/flashchip.h>
+
+#define DRV_NAME "vr_nor"
+
+struct vr_nor_mtd {
+	void __iomem *csr_base;
+	struct map_info map;
+	struct mtd_info *info;
+	struct pci_dev *dev;
+};
+
+/* Expansion Bus Configuration and Status Registers are in BAR 0 */
+#define EXP_CSR_MBAR 0
+/* Expansion Bus Memory Window is BAR 1 */
+#define EXP_WIN_MBAR 1
+/* Maximum address space for Chip Select 0 is 64MiB */
+#define CS0_SIZE 0x04000000
+/* Chip Select 0 is at offset 0 in the Memory Window */
+#define CS0_START 0x0
+/* Chip Select 0 Timing Register is at offset 0 in CSR */
+#define EXP_TIMING_CS0 0x00
+#define TIMING_CS_EN		(1 << 31)	/* Chip Select Enable */
+#define TIMING_BOOT_ACCEL_DIS	(1 <<  8)	/* Boot Acceleration Disable */
+#define TIMING_WR_EN		(1 <<  1)	/* Write Enable */
+#define TIMING_BYTE_EN		(1 <<  0)	/* 8-bit vs 16-bit bus */
+#define TIMING_MASK		0x3FFF0000
+
+static void vr_nor_destroy_partitions(struct vr_nor_mtd *p)
+{
+	mtd_device_unregister(p->info);
+}
+
+static int vr_nor_init_partitions(struct vr_nor_mtd *p)
+{
+	/* register the flash bank */
+	/* partition the flash bank */
+	return mtd_device_parse_register(p->info, NULL, NULL, NULL, 0);
+}
+
+static void vr_nor_destroy_mtd_setup(struct vr_nor_mtd *p)
+{
+	map_destroy(p->info);
+}
+
+static int vr_nor_mtd_setup(struct vr_nor_mtd *p)
+{
+	static const char * const probe_types[] =
+	    { "cfi_probe", "jedec_probe", NULL };
+	const char * const *type;
+
+	for (type = probe_types; !p->info && *type; type++)
+		p->info = do_map_probe(*type, &p->map);
+	if (!p->info)
+		return -ENODEV;
+
+	p->info->owner = THIS_MODULE;
+
+	return 0;
+}
+
+static void vr_nor_destroy_maps(struct vr_nor_mtd *p)
+{
+	unsigned int exp_timing_cs0;
+
+	/* write-protect the flash bank */
+	exp_timing_cs0 = readl(p->csr_base + EXP_TIMING_CS0);
+	exp_timing_cs0 &= ~TIMING_WR_EN;
+	writel(exp_timing_cs0, p->csr_base + EXP_TIMING_CS0);
+
+	/* unmap the flash window */
+	iounmap(p->map.virt);
+
+	/* unmap the csr window */
+	iounmap(p->csr_base);
+}
+
+/*
+ * Initialize the map_info structure and map the flash.
+ * Returns 0 on success, nonzero otherwise.
+ */
+static int vr_nor_init_maps(struct vr_nor_mtd *p)
+{
+	unsigned long csr_phys, csr_len;
+	unsigned long win_phys, win_len;
+	unsigned int exp_timing_cs0;
+	int err;
+
+	csr_phys = pci_resource_start(p->dev, EXP_CSR_MBAR);
+	csr_len = pci_resource_len(p->dev, EXP_CSR_MBAR);
+	win_phys = pci_resource_start(p->dev, EXP_WIN_MBAR);
+	win_len = pci_resource_len(p->dev, EXP_WIN_MBAR);
+
+	if (!csr_phys || !csr_len || !win_phys || !win_len)
+		return -ENODEV;
+
+	if (win_len < (CS0_START + CS0_SIZE))
+		return -ENXIO;
+
+	p->csr_base = ioremap_nocache(csr_phys, csr_len);
+	if (!p->csr_base)
+		return -ENOMEM;
+
+	exp_timing_cs0 = readl(p->csr_base + EXP_TIMING_CS0);
+	if (!(exp_timing_cs0 & TIMING_CS_EN)) {
+		dev_warn(&p->dev->dev, "Expansion Bus Chip Select 0 "
+		       "is disabled.\n");
+		err = -ENODEV;
+		goto release;
+	}
+	if ((exp_timing_cs0 & TIMING_MASK) == TIMING_MASK) {
+		dev_warn(&p->dev->dev, "Expansion Bus Chip Select 0 "
+		       "is configured for maximally slow access times.\n");
+	}
+	p->map.name = DRV_NAME;
+	p->map.bankwidth = (exp_timing_cs0 & TIMING_BYTE_EN) ? 1 : 2;
+	p->map.phys = win_phys + CS0_START;
+	p->map.size = CS0_SIZE;
+	p->map.virt = ioremap_nocache(p->map.phys, p->map.size);
+	if (!p->map.virt) {
+		err = -ENOMEM;
+		goto release;
+	}
+	simple_map_init(&p->map);
+
+	/* Enable writes to flash bank */
+	exp_timing_cs0 |= TIMING_BOOT_ACCEL_DIS | TIMING_WR_EN;
+	writel(exp_timing_cs0, p->csr_base + EXP_TIMING_CS0);
+
+	return 0;
+
+      release:
+	iounmap(p->csr_base);
+	return err;
+}
+
+static struct pci_device_id vr_nor_pci_ids[] = {
+	{PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x500D)},
+	{0,}
+};
+
+static void vr_nor_pci_remove(struct pci_dev *dev)
+{
+	struct vr_nor_mtd *p = pci_get_drvdata(dev);
+
+	vr_nor_destroy_partitions(p);
+	vr_nor_destroy_mtd_setup(p);
+	vr_nor_destroy_maps(p);
+	kfree(p);
+	pci_release_regions(dev);
+	pci_disable_device(dev);
+}
+
+static int vr_nor_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	struct vr_nor_mtd *p = NULL;
+	unsigned int exp_timing_cs0;
+	int err;
+
+	err = pci_enable_device(dev);
+	if (err)
+		goto out;
+
+	err = pci_request_regions(dev, DRV_NAME);
+	if (err)
+		goto disable_dev;
+
+	p = kzalloc(sizeof(*p), GFP_KERNEL);
+	err = -ENOMEM;
+	if (!p)
+		goto release;
+
+	p->dev = dev;
+
+	err = vr_nor_init_maps(p);
+	if (err)
+		goto release;
+
+	err = vr_nor_mtd_setup(p);
+	if (err)
+		goto destroy_maps;
+
+	err = vr_nor_init_partitions(p);
+	if (err)
+		goto destroy_mtd_setup;
+
+	pci_set_drvdata(dev, p);
+
+	return 0;
+
+      destroy_mtd_setup:
+	map_destroy(p->info);
+
+      destroy_maps:
+	/* write-protect the flash bank */
+	exp_timing_cs0 = readl(p->csr_base + EXP_TIMING_CS0);
+	exp_timing_cs0 &= ~TIMING_WR_EN;
+	writel(exp_timing_cs0, p->csr_base + EXP_TIMING_CS0);
+
+	/* unmap the flash window */
+	iounmap(p->map.virt);
+
+	/* unmap the csr window */
+	iounmap(p->csr_base);
+
+      release:
+	kfree(p);
+	pci_release_regions(dev);
+
+      disable_dev:
+	pci_disable_device(dev);
+
+      out:
+	return err;
+}
+
+static struct pci_driver vr_nor_pci_driver = {
+	.name = DRV_NAME,
+	.probe = vr_nor_pci_probe,
+	.remove = vr_nor_pci_remove,
+	.id_table = vr_nor_pci_ids,
+};
+
+module_pci_driver(vr_nor_pci_driver);
+
+MODULE_AUTHOR("Andy Lowe");
+MODULE_DESCRIPTION("MTD map driver for NOR flash on Intel Vermilion Range");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, vr_nor_pci_ids);
diff --git a/drivers/mtd/maps/ixp4xx.c b/drivers/mtd/maps/ixp4xx.c
new file mode 100644
index 000000000..b44307410
--- /dev/null
+++ b/drivers/mtd/maps/ixp4xx.c
@@ -0,0 +1,261 @@
+/*
+ * drivers/mtd/maps/ixp4xx.c
+ *
+ * MTD Map file for IXP4XX based systems. Please do not make per-board
+ * changes in here. If your board needs special setup, do it in your
+ * platform level code in arch/arm/mach-ixp4xx/board-setup.c
+ *
+ * Original Author: Intel Corporation
+ * Maintainer: Deepak Saxena <dsaxena@mvista.com>
+ *
+ * Copyright (C) 2002 Intel Corporation
+ * Copyright (C) 2003-2004 MontaVista Software, Inc.
+ *
+ */
+
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/slab.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/io.h>
+#include <asm/mach/flash.h>
+
+#include <linux/reboot.h>
+
+/*
+ * Read/write a 16 bit word from flash address 'addr'.
+ *
+ * When the cpu is in little-endian mode it swizzles the address lines
+ * ('address coherency') so we need to undo the swizzling to ensure commands
+ * and the like end up on the correct flash address.
+ *
+ * To further complicate matters, due to the way the expansion bus controller
+ * handles 32 bit reads, the byte stream ABCD is stored on the flash as:
+ *     D15    D0
+ *     +---+---+
+ *     | A | B | 0
+ *     +---+---+
+ *     | C | D | 2
+ *     +---+---+
+ * This means that on LE systems each 16 bit word must be swapped. Note that
+ * this requires CONFIG_MTD_CFI_BE_BYTE_SWAP to be enabled to 'unswap' the CFI
+ * data and other flash commands which are always in D7-D0.
+ */
+#ifndef __ARMEB__
+#ifndef CONFIG_MTD_CFI_BE_BYTE_SWAP
+#  error CONFIG_MTD_CFI_BE_BYTE_SWAP required
+#endif
+
+static inline u16 flash_read16(void __iomem *addr)
+{
+	return be16_to_cpu(__raw_readw((void __iomem *)((unsigned long)addr ^ 0x2)));
+}
+
+static inline void flash_write16(u16 d, void __iomem *addr)
+{
+	__raw_writew(cpu_to_be16(d), (void __iomem *)((unsigned long)addr ^ 0x2));
+}
+
+#define	BYTE0(h)	((h) & 0xFF)
+#define	BYTE1(h)	(((h) >> 8) & 0xFF)
+
+#else
+
+static inline u16 flash_read16(const void __iomem *addr)
+{
+	return __raw_readw(addr);
+}
+
+static inline void flash_write16(u16 d, void __iomem *addr)
+{
+	__raw_writew(d, addr);
+}
+
+#define	BYTE0(h)	(((h) >> 8) & 0xFF)
+#define	BYTE1(h)	((h) & 0xFF)
+#endif
+
+static map_word ixp4xx_read16(struct map_info *map, unsigned long ofs)
+{
+	map_word val;
+	val.x[0] = flash_read16(map->virt + ofs);
+	return val;
+}
+
+/*
+ * The IXP4xx expansion bus only allows 16-bit wide acceses
+ * when attached to a 16-bit wide device (such as the 28F128J3A),
+ * so we can't just memcpy_fromio().
+ */
+static void ixp4xx_copy_from(struct map_info *map, void *to,
+			     unsigned long from, ssize_t len)
+{
+	u8 *dest = (u8 *) to;
+	void __iomem *src = map->virt + from;
+
+	if (len <= 0)
+		return;
+
+	if (from & 1) {
+		*dest++ = BYTE1(flash_read16(src-1));
+		src++;
+		--len;
+	}
+
+	while (len >= 2) {
+		u16 data = flash_read16(src);
+		*dest++ = BYTE0(data);
+		*dest++ = BYTE1(data);
+		src += 2;
+		len -= 2;
+	}
+
+	if (len > 0)
+		*dest++ = BYTE0(flash_read16(src));
+}
+
+/*
+ * Unaligned writes are ignored, causing the 8-bit
+ * probe to fail and proceed to the 16-bit probe (which succeeds).
+ */
+static void ixp4xx_probe_write16(struct map_info *map, map_word d, unsigned long adr)
+{
+	if (!(adr & 1))
+		flash_write16(d.x[0], map->virt + adr);
+}
+
+/*
+ * Fast write16 function without the probing check above
+ */
+static void ixp4xx_write16(struct map_info *map, map_word d, unsigned long adr)
+{
+	flash_write16(d.x[0], map->virt + adr);
+}
+
+struct ixp4xx_flash_info {
+	struct mtd_info *mtd;
+	struct map_info map;
+	struct resource *res;
+};
+
+static const char * const probes[] = { "RedBoot", "cmdlinepart", NULL };
+
+static int ixp4xx_flash_remove(struct platform_device *dev)
+{
+	struct flash_platform_data *plat = dev_get_platdata(&dev->dev);
+	struct ixp4xx_flash_info *info = platform_get_drvdata(dev);
+
+	if(!info)
+		return 0;
+
+	if (info->mtd) {
+		mtd_device_unregister(info->mtd);
+		map_destroy(info->mtd);
+	}
+
+	if (plat->exit)
+		plat->exit();
+
+	return 0;
+}
+
+static int ixp4xx_flash_probe(struct platform_device *dev)
+{
+	struct flash_platform_data *plat = dev_get_platdata(&dev->dev);
+	struct ixp4xx_flash_info *info;
+	struct mtd_part_parser_data ppdata = {
+		.origin = dev->resource->start,
+	};
+	int err = -1;
+
+	if (!plat)
+		return -ENODEV;
+
+	if (plat->init) {
+		err = plat->init();
+		if (err)
+			return err;
+	}
+
+	info = devm_kzalloc(&dev->dev, sizeof(struct ixp4xx_flash_info),
+			    GFP_KERNEL);
+	if(!info) {
+		err = -ENOMEM;
+		goto Error;
+	}
+
+	platform_set_drvdata(dev, info);
+
+	/*
+	 * Tell the MTD layer we're not 1:1 mapped so that it does
+	 * not attempt to do a direct access on us.
+	 */
+	info->map.phys = NO_XIP;
+	info->map.size = resource_size(dev->resource);
+
+	/*
+	 * We only support 16-bit accesses for now. If and when
+	 * any board use 8-bit access, we'll fixup the driver to
+	 * handle that.
+	 */
+	info->map.bankwidth = 2;
+	info->map.name = dev_name(&dev->dev);
+	info->map.read = ixp4xx_read16;
+	info->map.write = ixp4xx_probe_write16;
+	info->map.copy_from = ixp4xx_copy_from;
+
+	info->map.virt = devm_ioremap_resource(&dev->dev, dev->resource);
+	if (IS_ERR(info->map.virt)) {
+		err = PTR_ERR(info->map.virt);
+		goto Error;
+	}
+
+	info->mtd = do_map_probe(plat->map_name, &info->map);
+	if (!info->mtd) {
+		printk(KERN_ERR "IXP4XXFlash: map_probe failed\n");
+		err = -ENXIO;
+		goto Error;
+	}
+	info->mtd->owner = THIS_MODULE;
+
+	/* Use the fast version */
+	info->map.write = ixp4xx_write16;
+
+	err = mtd_device_parse_register(info->mtd, probes, &ppdata,
+			plat->parts, plat->nr_parts);
+	if (err) {
+		printk(KERN_ERR "Could not parse partitions\n");
+		goto Error;
+	}
+
+	return 0;
+
+Error:
+	ixp4xx_flash_remove(dev);
+	return err;
+}
+
+static struct platform_driver ixp4xx_flash_driver = {
+	.probe		= ixp4xx_flash_probe,
+	.remove		= ixp4xx_flash_remove,
+	.driver		= {
+		.name	= "IXP4XX-Flash",
+	},
+};
+
+module_platform_driver(ixp4xx_flash_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("MTD map driver for Intel IXP4xx systems");
+MODULE_AUTHOR("Deepak Saxena");
+MODULE_ALIAS("platform:IXP4XX-Flash");
diff --git a/drivers/mtd/maps/l440gx.c b/drivers/mtd/maps/l440gx.c
new file mode 100644
index 000000000..74bd98ee6
--- /dev/null
+++ b/drivers/mtd/maps/l440gx.c
@@ -0,0 +1,166 @@
+/*
+ * BIOS Flash chip on Intel 440GX board.
+ *
+ * Bugs this currently does not work under linuxBIOS.
+ */
+
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+
+#define PIIXE_IOBASE_RESOURCE	11
+
+#define WINDOW_ADDR 0xfff00000
+#define WINDOW_SIZE 0x00100000
+#define BUSWIDTH 1
+
+static u32 iobase;
+#define IOBASE iobase
+#define TRIBUF_PORT (IOBASE+0x37)
+#define VPP_PORT (IOBASE+0x28)
+
+static struct mtd_info *mymtd;
+
+
+/* Is this really the vpp port? */
+static DEFINE_SPINLOCK(l440gx_vpp_lock);
+static int l440gx_vpp_refcnt;
+static void l440gx_set_vpp(struct map_info *map, int vpp)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&l440gx_vpp_lock, flags);
+	if (vpp) {
+		if (++l440gx_vpp_refcnt == 1)   /* first nested 'on' */
+			outl(inl(VPP_PORT) | 1, VPP_PORT);
+	} else {
+		if (--l440gx_vpp_refcnt == 0)   /* last nested 'off' */
+			outl(inl(VPP_PORT) & ~1, VPP_PORT);
+	}
+	spin_unlock_irqrestore(&l440gx_vpp_lock, flags);
+}
+
+static struct map_info l440gx_map = {
+	.name = "L440GX BIOS",
+	.size = WINDOW_SIZE,
+	.bankwidth = BUSWIDTH,
+	.phys = WINDOW_ADDR,
+#if 0
+	/* FIXME verify that this is the
+	 * appripriate code for vpp enable/disable
+	 */
+	.set_vpp = l440gx_set_vpp
+#endif
+};
+
+static int __init init_l440gx(void)
+{
+	struct pci_dev *dev, *pm_dev;
+	struct resource *pm_iobase;
+	__u16 word;
+
+	dev = pci_get_device(PCI_VENDOR_ID_INTEL,
+		PCI_DEVICE_ID_INTEL_82371AB_0, NULL);
+
+	pm_dev = pci_get_device(PCI_VENDOR_ID_INTEL,
+		PCI_DEVICE_ID_INTEL_82371AB_3, NULL);
+
+	pci_dev_put(dev);
+
+	if (!dev || !pm_dev) {
+		printk(KERN_NOTICE "L440GX flash mapping: failed to find PIIX4 ISA bridge, cannot continue\n");
+		pci_dev_put(pm_dev);
+		return -ENODEV;
+	}
+
+	l440gx_map.virt = ioremap_nocache(WINDOW_ADDR, WINDOW_SIZE);
+
+	if (!l440gx_map.virt) {
+		printk(KERN_WARNING "Failed to ioremap L440GX flash region\n");
+		pci_dev_put(pm_dev);
+		return -ENOMEM;
+	}
+	simple_map_init(&l440gx_map);
+	printk(KERN_NOTICE "window_addr = 0x%08lx\n", (unsigned long)l440gx_map.virt);
+
+	/* Setup the pm iobase resource
+	 * This code should move into some kind of generic bridge
+	 * driver but for the moment I'm content with getting the
+	 * allocation correct.
+	 */
+	pm_iobase = &pm_dev->resource[PIIXE_IOBASE_RESOURCE];
+	if (!(pm_iobase->flags & IORESOURCE_IO)) {
+		pm_iobase->name = "pm iobase";
+		pm_iobase->start = 0;
+		pm_iobase->end = 63;
+		pm_iobase->flags = IORESOURCE_IO;
+
+		/* Put the current value in the resource */
+		pci_read_config_dword(pm_dev, 0x40, &iobase);
+		iobase &= ~1;
+		pm_iobase->start += iobase & ~1;
+		pm_iobase->end += iobase & ~1;
+
+		pci_dev_put(pm_dev);
+
+		/* Allocate the resource region */
+		if (pci_assign_resource(pm_dev, PIIXE_IOBASE_RESOURCE) != 0) {
+			pci_dev_put(dev);
+			pci_dev_put(pm_dev);
+			printk(KERN_WARNING "Could not allocate pm iobase resource\n");
+			iounmap(l440gx_map.virt);
+			return -ENXIO;
+		}
+	}
+	/* Set the iobase */
+	iobase = pm_iobase->start;
+	pci_write_config_dword(pm_dev, 0x40, iobase | 1);
+
+
+	/* Set XBCS# */
+	pci_read_config_word(dev, 0x4e, &word);
+	word |= 0x4;
+        pci_write_config_word(dev, 0x4e, word);
+
+	/* Supply write voltage to the chip */
+	l440gx_set_vpp(&l440gx_map, 1);
+
+	/* Enable the gate on the WE line */
+	outb(inb(TRIBUF_PORT) & ~1, TRIBUF_PORT);
+
+       	printk(KERN_NOTICE "Enabled WE line to L440GX BIOS flash chip.\n");
+
+	mymtd = do_map_probe("jedec_probe", &l440gx_map);
+	if (!mymtd) {
+		printk(KERN_NOTICE "JEDEC probe on BIOS chip failed. Using ROM\n");
+		mymtd = do_map_probe("map_rom", &l440gx_map);
+	}
+	if (mymtd) {
+		mymtd->owner = THIS_MODULE;
+
+		mtd_device_register(mymtd, NULL, 0);
+		return 0;
+	}
+
+	iounmap(l440gx_map.virt);
+	return -ENXIO;
+}
+
+static void __exit cleanup_l440gx(void)
+{
+	mtd_device_unregister(mymtd);
+	map_destroy(mymtd);
+
+	iounmap(l440gx_map.virt);
+}
+
+module_init(init_l440gx);
+module_exit(cleanup_l440gx);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>");
+MODULE_DESCRIPTION("MTD map driver for BIOS chips on Intel L440GX motherboards");
diff --git a/drivers/mtd/maps/lantiq-flash.c b/drivers/mtd/maps/lantiq-flash.c
new file mode 100644
index 000000000..33d26f5be
--- /dev/null
+++ b/drivers/mtd/maps/lantiq-flash.c
@@ -0,0 +1,216 @@
+/*
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ *
+ *  Copyright (C) 2004 Liu Peng Infineon IFAP DC COM CPE
+ *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
+ */
+
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/cfi.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/of.h>
+
+#include <lantiq_soc.h>
+
+/*
+ * The NOR flash is connected to the same external bus unit (EBU) as PCI.
+ * To make PCI work we need to enable the endianness swapping for the address
+ * written to the EBU. This endianness swapping works for PCI correctly but
+ * fails for attached NOR devices. To workaround this we need to use a complex
+ * map. The workaround involves swapping all addresses whilst probing the chip.
+ * Once probing is complete we stop swapping the addresses but swizzle the
+ * unlock addresses to ensure that access to the NOR device works correctly.
+ */
+
+enum {
+	LTQ_NOR_PROBING,
+	LTQ_NOR_NORMAL
+};
+
+struct ltq_mtd {
+	struct resource *res;
+	struct mtd_info *mtd;
+	struct map_info *map;
+};
+
+static const char ltq_map_name[] = "ltq_nor";
+static const char * const ltq_probe_types[] = { "cmdlinepart", "ofpart", NULL };
+
+static map_word
+ltq_read16(struct map_info *map, unsigned long adr)
+{
+	unsigned long flags;
+	map_word temp;
+
+	if (map->map_priv_1 == LTQ_NOR_PROBING)
+		adr ^= 2;
+	spin_lock_irqsave(&ebu_lock, flags);
+	temp.x[0] = *(u16 *)(map->virt + adr);
+	spin_unlock_irqrestore(&ebu_lock, flags);
+	return temp;
+}
+
+static void
+ltq_write16(struct map_info *map, map_word d, unsigned long adr)
+{
+	unsigned long flags;
+
+	if (map->map_priv_1 == LTQ_NOR_PROBING)
+		adr ^= 2;
+	spin_lock_irqsave(&ebu_lock, flags);
+	*(u16 *)(map->virt + adr) = d.x[0];
+	spin_unlock_irqrestore(&ebu_lock, flags);
+}
+
+/*
+ * The following 2 functions copy data between iomem and a cached memory
+ * section. As memcpy() makes use of pre-fetching we cannot use it here.
+ * The normal alternative of using memcpy_{to,from}io also makes use of
+ * memcpy() on MIPS so it is not applicable either. We are therefore stuck
+ * with having to use our own loop.
+ */
+static void
+ltq_copy_from(struct map_info *map, void *to,
+	unsigned long from, ssize_t len)
+{
+	unsigned char *f = (unsigned char *)map->virt + from;
+	unsigned char *t = (unsigned char *)to;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ebu_lock, flags);
+	while (len--)
+		*t++ = *f++;
+	spin_unlock_irqrestore(&ebu_lock, flags);
+}
+
+static void
+ltq_copy_to(struct map_info *map, unsigned long to,
+	const void *from, ssize_t len)
+{
+	unsigned char *f = (unsigned char *)from;
+	unsigned char *t = (unsigned char *)map->virt + to;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ebu_lock, flags);
+	while (len--)
+		*t++ = *f++;
+	spin_unlock_irqrestore(&ebu_lock, flags);
+}
+
+static int
+ltq_mtd_probe(struct platform_device *pdev)
+{
+	struct mtd_part_parser_data ppdata;
+	struct ltq_mtd *ltq_mtd;
+	struct cfi_private *cfi;
+	int err;
+
+	if (of_machine_is_compatible("lantiq,falcon") &&
+			(ltq_boot_select() != BS_FLASH)) {
+		dev_err(&pdev->dev, "invalid bootstrap options\n");
+		return -ENODEV;
+	}
+
+	ltq_mtd = devm_kzalloc(&pdev->dev, sizeof(struct ltq_mtd), GFP_KERNEL);
+	if (!ltq_mtd)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, ltq_mtd);
+
+	ltq_mtd->res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!ltq_mtd->res) {
+		dev_err(&pdev->dev, "failed to get memory resource\n");
+		return -ENOENT;
+	}
+
+	ltq_mtd->map = devm_kzalloc(&pdev->dev, sizeof(struct map_info),
+				    GFP_KERNEL);
+	if (!ltq_mtd->map)
+		return -ENOMEM;
+
+	ltq_mtd->map->phys = ltq_mtd->res->start;
+	ltq_mtd->map->size = resource_size(ltq_mtd->res);
+	ltq_mtd->map->virt = devm_ioremap_resource(&pdev->dev, ltq_mtd->res);
+	if (IS_ERR(ltq_mtd->map->virt))
+		return PTR_ERR(ltq_mtd->map->virt);
+
+	ltq_mtd->map->name = ltq_map_name;
+	ltq_mtd->map->bankwidth = 2;
+	ltq_mtd->map->read = ltq_read16;
+	ltq_mtd->map->write = ltq_write16;
+	ltq_mtd->map->copy_from = ltq_copy_from;
+	ltq_mtd->map->copy_to = ltq_copy_to;
+
+	ltq_mtd->map->map_priv_1 = LTQ_NOR_PROBING;
+	ltq_mtd->mtd = do_map_probe("cfi_probe", ltq_mtd->map);
+	ltq_mtd->map->map_priv_1 = LTQ_NOR_NORMAL;
+
+	if (!ltq_mtd->mtd) {
+		dev_err(&pdev->dev, "probing failed\n");
+		return -ENXIO;
+	}
+
+	ltq_mtd->mtd->owner = THIS_MODULE;
+
+	cfi = ltq_mtd->map->fldrv_priv;
+	cfi->addr_unlock1 ^= 1;
+	cfi->addr_unlock2 ^= 1;
+
+	ppdata.of_node = pdev->dev.of_node;
+	err = mtd_device_parse_register(ltq_mtd->mtd, ltq_probe_types,
+					&ppdata, NULL, 0);
+	if (err) {
+		dev_err(&pdev->dev, "failed to add partitions\n");
+		goto err_destroy;
+	}
+
+	return 0;
+
+err_destroy:
+	map_destroy(ltq_mtd->mtd);
+	return err;
+}
+
+static int
+ltq_mtd_remove(struct platform_device *pdev)
+{
+	struct ltq_mtd *ltq_mtd = platform_get_drvdata(pdev);
+
+	if (ltq_mtd && ltq_mtd->mtd) {
+		mtd_device_unregister(ltq_mtd->mtd);
+		map_destroy(ltq_mtd->mtd);
+	}
+	return 0;
+}
+
+static const struct of_device_id ltq_mtd_match[] = {
+	{ .compatible = "lantiq,nor" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, ltq_mtd_match);
+
+static struct platform_driver ltq_mtd_driver = {
+	.probe = ltq_mtd_probe,
+	.remove = ltq_mtd_remove,
+	.driver = {
+		.name = "ltq-nor",
+		.of_match_table = ltq_mtd_match,
+	},
+};
+
+module_platform_driver(ltq_mtd_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("John Crispin <blogic@openwrt.org>");
+MODULE_DESCRIPTION("Lantiq SoC NOR");
diff --git a/drivers/mtd/maps/latch-addr-flash.c b/drivers/mtd/maps/latch-addr-flash.c
new file mode 100644
index 000000000..cadfbe051
--- /dev/null
+++ b/drivers/mtd/maps/latch-addr-flash.c
@@ -0,0 +1,230 @@
+/*
+ * Interface for NOR flash driver whose high address lines are latched
+ *
+ * Copyright © 2000 Nicolas Pitre <nico@cam.org>
+ * Copyright © 2005-2008 Analog Devices Inc.
+ * Copyright © 2008 MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/latch-addr-flash.h>
+#include <linux/slab.h>
+
+#define DRIVER_NAME "latch-addr-flash"
+
+struct latch_addr_flash_info {
+	struct mtd_info		*mtd;
+	struct map_info		map;
+	struct resource		*res;
+
+	void			(*set_window)(unsigned long offset, void *data);
+	void			*data;
+
+	/* cache; could be found out of res */
+	unsigned long		win_mask;
+
+	spinlock_t		lock;
+};
+
+static map_word lf_read(struct map_info *map, unsigned long ofs)
+{
+	struct latch_addr_flash_info *info;
+	map_word datum;
+
+	info = (struct latch_addr_flash_info *)map->map_priv_1;
+
+	spin_lock(&info->lock);
+
+	info->set_window(ofs, info->data);
+	datum = inline_map_read(map, info->win_mask & ofs);
+
+	spin_unlock(&info->lock);
+
+	return datum;
+}
+
+static void lf_write(struct map_info *map, map_word datum, unsigned long ofs)
+{
+	struct latch_addr_flash_info *info;
+
+	info = (struct latch_addr_flash_info *)map->map_priv_1;
+
+	spin_lock(&info->lock);
+
+	info->set_window(ofs, info->data);
+	inline_map_write(map, datum, info->win_mask & ofs);
+
+	spin_unlock(&info->lock);
+}
+
+static void lf_copy_from(struct map_info *map, void *to,
+		unsigned long from, ssize_t len)
+{
+	struct latch_addr_flash_info *info =
+		(struct latch_addr_flash_info *) map->map_priv_1;
+	unsigned n;
+
+	while (len > 0) {
+		n = info->win_mask + 1 - (from & info->win_mask);
+		if (n > len)
+			n = len;
+
+		spin_lock(&info->lock);
+
+		info->set_window(from, info->data);
+		memcpy_fromio(to, map->virt + (from & info->win_mask), n);
+
+		spin_unlock(&info->lock);
+
+		to += n;
+		from += n;
+		len -= n;
+	}
+}
+
+static char *rom_probe_types[] = { "cfi_probe", NULL };
+
+static int latch_addr_flash_remove(struct platform_device *dev)
+{
+	struct latch_addr_flash_info *info;
+	struct latch_addr_flash_data *latch_addr_data;
+
+	info = platform_get_drvdata(dev);
+	if (info == NULL)
+		return 0;
+
+	latch_addr_data = dev_get_platdata(&dev->dev);
+
+	if (info->mtd != NULL) {
+		mtd_device_unregister(info->mtd);
+		map_destroy(info->mtd);
+	}
+
+	if (info->map.virt != NULL)
+		iounmap(info->map.virt);
+
+	if (info->res != NULL)
+		release_mem_region(info->res->start, resource_size(info->res));
+
+	kfree(info);
+
+	if (latch_addr_data->done)
+		latch_addr_data->done(latch_addr_data->data);
+
+	return 0;
+}
+
+static int latch_addr_flash_probe(struct platform_device *dev)
+{
+	struct latch_addr_flash_data *latch_addr_data;
+	struct latch_addr_flash_info *info;
+	resource_size_t win_base = dev->resource->start;
+	resource_size_t win_size = resource_size(dev->resource);
+	char **probe_type;
+	int chipsel;
+	int err;
+
+	latch_addr_data = dev_get_platdata(&dev->dev);
+	if (latch_addr_data == NULL)
+		return -ENODEV;
+
+	pr_notice("latch-addr platform flash device: %#llx byte "
+		  "window at %#.8llx\n",
+		  (unsigned long long)win_size, (unsigned long long)win_base);
+
+	chipsel = dev->id;
+
+	if (latch_addr_data->init) {
+		err = latch_addr_data->init(latch_addr_data->data, chipsel);
+		if (err != 0)
+			return err;
+	}
+
+	info = kzalloc(sizeof(struct latch_addr_flash_info), GFP_KERNEL);
+	if (info == NULL) {
+		err = -ENOMEM;
+		goto done;
+	}
+
+	platform_set_drvdata(dev, info);
+
+	info->res = request_mem_region(win_base, win_size, DRIVER_NAME);
+	if (info->res == NULL) {
+		dev_err(&dev->dev, "Could not reserve memory region\n");
+		err = -EBUSY;
+		goto free_info;
+	}
+
+	info->map.name		= DRIVER_NAME;
+	info->map.size		= latch_addr_data->size;
+	info->map.bankwidth	= latch_addr_data->width;
+
+	info->map.phys		= NO_XIP;
+	info->map.virt		= ioremap(win_base, win_size);
+	if (!info->map.virt) {
+		err = -ENOMEM;
+		goto free_res;
+	}
+
+	info->map.map_priv_1	= (unsigned long)info;
+
+	info->map.read		= lf_read;
+	info->map.copy_from	= lf_copy_from;
+	info->map.write		= lf_write;
+	info->set_window	= latch_addr_data->set_window;
+	info->data		= latch_addr_data->data;
+	info->win_mask		= win_size - 1;
+
+	spin_lock_init(&info->lock);
+
+	for (probe_type = rom_probe_types; !info->mtd && *probe_type;
+		probe_type++)
+		info->mtd = do_map_probe(*probe_type, &info->map);
+
+	if (info->mtd == NULL) {
+		dev_err(&dev->dev, "map_probe failed\n");
+		err = -ENODEV;
+		goto iounmap;
+	}
+	info->mtd->owner = THIS_MODULE;
+
+	mtd_device_parse_register(info->mtd, NULL, NULL,
+				  latch_addr_data->parts,
+				  latch_addr_data->nr_parts);
+	return 0;
+
+iounmap:
+	iounmap(info->map.virt);
+free_res:
+	release_mem_region(info->res->start, resource_size(info->res));
+free_info:
+	kfree(info);
+done:
+	if (latch_addr_data->done)
+		latch_addr_data->done(latch_addr_data->data);
+	return err;
+}
+
+static struct platform_driver latch_addr_flash_driver = {
+	.probe		= latch_addr_flash_probe,
+	.remove		= latch_addr_flash_remove,
+	.driver		= {
+		.name	= DRIVER_NAME,
+	},
+};
+
+module_platform_driver(latch_addr_flash_driver);
+
+MODULE_AUTHOR("David Griego <dgriego@mvista.com>");
+MODULE_DESCRIPTION("MTD map driver for flashes addressed physically with upper "
+		"address lines being set board specifically");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/mtd/maps/map_funcs.c b/drivers/mtd/maps/map_funcs.c
new file mode 100644
index 000000000..3f268370e
--- /dev/null
+++ b/drivers/mtd/maps/map_funcs.c
@@ -0,0 +1,43 @@
+/*
+ * Out-of-line map I/O functions for simple maps when CONFIG_COMPLEX_MAPPINGS
+ * is enabled.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+
+#include <linux/mtd/map.h>
+#include <linux/mtd/xip.h>
+
+static map_word __xipram simple_map_read(struct map_info *map, unsigned long ofs)
+{
+	return inline_map_read(map, ofs);
+}
+
+static void __xipram simple_map_write(struct map_info *map, const map_word datum, unsigned long ofs)
+{
+	inline_map_write(map, datum, ofs);
+}
+
+static void __xipram simple_map_copy_from(struct map_info *map, void *to, unsigned long from, ssize_t len)
+{
+	inline_map_copy_from(map, to, from, len);
+}
+
+static void __xipram simple_map_copy_to(struct map_info *map, unsigned long to, const void *from, ssize_t len)
+{
+	inline_map_copy_to(map, to, from, len);
+}
+
+void simple_map_init(struct map_info *map)
+{
+	BUG_ON(!map_bankwidth_supported(map->bankwidth));
+
+	map->read = simple_map_read;
+	map->write = simple_map_write;
+	map->copy_from = simple_map_copy_from;
+	map->copy_to = simple_map_copy_to;
+}
+
+EXPORT_SYMBOL(simple_map_init);
+MODULE_LICENSE("GPL");
diff --git a/drivers/mtd/maps/netsc520.c b/drivers/mtd/maps/netsc520.c
new file mode 100644
index 000000000..81dc2598b
--- /dev/null
+++ b/drivers/mtd/maps/netsc520.c
@@ -0,0 +1,140 @@
+/* netsc520.c -- MTD map driver for AMD NetSc520 Demonstration Board
+ *
+ * Copyright (C) 2001 Mark Langsdorf (mark.langsdorf@amd.com)
+ *	based on sc520cdp.c by Sysgo Real-Time Solutions GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
+ *
+ * The NetSc520 is a demonstration board for the Elan Sc520 processor available
+ * from AMD.  It has a single back of 16 megs of 32-bit Flash ROM and another
+ * 16 megs of SDRAM.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+
+/*
+** The single, 16 megabyte flash bank is divided into four virtual
+** partitions.  The first partition is 768 KiB and is intended to
+** store the kernel image loaded by the bootstrap loader.  The second
+** partition is 256 KiB and holds the BIOS image.  The third
+** partition is 14.5 MiB and is intended for the flash file system
+** image.  The last partition is 512 KiB and contains another copy
+** of the BIOS image and the reset vector.
+**
+** Only the third partition should be mounted.  The first partition
+** should not be mounted, but it can erased and written to using the
+** MTD character routines.  The second and fourth partitions should
+** not be touched - it is possible to corrupt the BIOS image by
+** mounting these partitions, and potentially the board will not be
+** recoverable afterwards.
+*/
+
+/* partition_info gives details on the logical partitions that the split the
+ * single flash device into. If the size if zero we use up to the end of the
+ * device. */
+static struct mtd_partition partition_info[]={
+    {
+	    .name = "NetSc520 boot kernel",
+	    .offset = 0,
+	    .size = 0xc0000
+    },
+    {
+	    .name = "NetSc520 Low BIOS",
+	    .offset = 0xc0000,
+	    .size = 0x40000
+    },
+    {
+	    .name = "NetSc520 file system",
+	    .offset = 0x100000,
+	    .size = 0xe80000
+    },
+    {
+	    .name = "NetSc520 High BIOS",
+	    .offset = 0xf80000,
+	    .size = 0x80000
+    },
+};
+#define NUM_PARTITIONS ARRAY_SIZE(partition_info)
+
+#define WINDOW_SIZE	0x00100000
+#define WINDOW_ADDR	0x00200000
+
+static struct map_info netsc520_map = {
+	.name = "netsc520 Flash Bank",
+	.size = WINDOW_SIZE,
+	.bankwidth = 4,
+	.phys = WINDOW_ADDR,
+};
+
+#define NUM_FLASH_BANKS	ARRAY_SIZE(netsc520_map)
+
+static struct mtd_info *mymtd;
+
+static int __init init_netsc520(void)
+{
+	printk(KERN_NOTICE "NetSc520 flash device: 0x%Lx at 0x%Lx\n",
+			(unsigned long long)netsc520_map.size,
+			(unsigned long long)netsc520_map.phys);
+	netsc520_map.virt = ioremap_nocache(netsc520_map.phys, netsc520_map.size);
+
+	if (!netsc520_map.virt) {
+		printk("Failed to ioremap_nocache\n");
+		return -EIO;
+	}
+
+	simple_map_init(&netsc520_map);
+
+	mymtd = do_map_probe("cfi_probe", &netsc520_map);
+	if(!mymtd)
+		mymtd = do_map_probe("map_ram", &netsc520_map);
+	if(!mymtd)
+		mymtd = do_map_probe("map_rom", &netsc520_map);
+
+	if (!mymtd) {
+		iounmap(netsc520_map.virt);
+		return -ENXIO;
+	}
+
+	mymtd->owner = THIS_MODULE;
+	mtd_device_register(mymtd, partition_info, NUM_PARTITIONS);
+	return 0;
+}
+
+static void __exit cleanup_netsc520(void)
+{
+	if (mymtd) {
+		mtd_device_unregister(mymtd);
+		map_destroy(mymtd);
+	}
+	if (netsc520_map.virt) {
+		iounmap(netsc520_map.virt);
+		netsc520_map.virt = NULL;
+	}
+}
+
+module_init(init_netsc520);
+module_exit(cleanup_netsc520);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Mark Langsdorf <mark.langsdorf@amd.com>");
+MODULE_DESCRIPTION("MTD map driver for AMD NetSc520 Demonstration Board");
diff --git a/drivers/mtd/maps/nettel.c b/drivers/mtd/maps/nettel.c
new file mode 100644
index 000000000..eadcfffc4
--- /dev/null
+++ b/drivers/mtd/maps/nettel.c
@@ -0,0 +1,454 @@
+/****************************************************************************/
+
+/*
+ *      nettel.c -- mappings for NETtel/SecureEdge/SnapGear (x86) boards.
+ *
+ *      (C) Copyright 2000-2001, Greg Ungerer (gerg@snapgear.com)
+ *      (C) Copyright 2001-2002, SnapGear (www.snapgear.com)
+ */
+
+/****************************************************************************/
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/cfi.h>
+#include <linux/reboot.h>
+#include <linux/err.h>
+#include <linux/kdev_t.h>
+#include <linux/root_dev.h>
+#include <asm/io.h>
+
+/****************************************************************************/
+
+#define INTEL_BUSWIDTH		1
+#define AMD_WINDOW_MAXSIZE	0x00200000
+#define AMD_BUSWIDTH	 	1
+
+/*
+ *	PAR masks and shifts, assuming 64K pages.
+ */
+#define SC520_PAR_ADDR_MASK	0x00003fff
+#define SC520_PAR_ADDR_SHIFT	16
+#define SC520_PAR_TO_ADDR(par) \
+	(((par)&SC520_PAR_ADDR_MASK) << SC520_PAR_ADDR_SHIFT)
+
+#define SC520_PAR_SIZE_MASK	0x01ffc000
+#define SC520_PAR_SIZE_SHIFT	2
+#define SC520_PAR_TO_SIZE(par) \
+	((((par)&SC520_PAR_SIZE_MASK) << SC520_PAR_SIZE_SHIFT) + (64*1024))
+
+#define SC520_PAR(cs, addr, size) \
+	((cs) | \
+	((((size)-(64*1024)) >> SC520_PAR_SIZE_SHIFT) & SC520_PAR_SIZE_MASK) | \
+	(((addr) >> SC520_PAR_ADDR_SHIFT) & SC520_PAR_ADDR_MASK))
+
+#define SC520_PAR_BOOTCS	0x8a000000
+#define	SC520_PAR_ROMCS1	0xaa000000
+#define SC520_PAR_ROMCS2	0xca000000	/* Cache disabled, 64K page */
+
+static void *nettel_mmcrp = NULL;
+
+#ifdef CONFIG_MTD_CFI_INTELEXT
+static struct mtd_info *intel_mtd;
+#endif
+static struct mtd_info *amd_mtd;
+
+/****************************************************************************/
+
+/****************************************************************************/
+
+#ifdef CONFIG_MTD_CFI_INTELEXT
+static struct map_info nettel_intel_map = {
+	.name = "SnapGear Intel",
+	.size = 0,
+	.bankwidth = INTEL_BUSWIDTH,
+};
+
+static struct mtd_partition nettel_intel_partitions[] = {
+	{
+		.name = "SnapGear kernel",
+		.offset = 0,
+		.size = 0x000e0000
+	},
+	{
+		.name = "SnapGear filesystem",
+		.offset = 0x00100000,
+	},
+	{
+		.name = "SnapGear config",
+		.offset = 0x000e0000,
+		.size = 0x00020000
+	},
+	{
+		.name = "SnapGear Intel",
+		.offset = 0
+	},
+	{
+		.name = "SnapGear BIOS Config",
+		.offset = 0x007e0000,
+		.size = 0x00020000
+	},
+	{
+		.name = "SnapGear BIOS",
+		.offset = 0x007e0000,
+		.size = 0x00020000
+	},
+};
+#endif
+
+static struct map_info nettel_amd_map = {
+	.name = "SnapGear AMD",
+	.size = AMD_WINDOW_MAXSIZE,
+	.bankwidth = AMD_BUSWIDTH,
+};
+
+static struct mtd_partition nettel_amd_partitions[] = {
+	{
+		.name = "SnapGear BIOS config",
+		.offset = 0x000e0000,
+		.size = 0x00010000
+	},
+	{
+		.name = "SnapGear BIOS",
+		.offset = 0x000f0000,
+		.size = 0x00010000
+	},
+	{
+		.name = "SnapGear AMD",
+		.offset = 0
+	},
+	{
+		.name = "SnapGear high BIOS",
+		.offset = 0x001f0000,
+		.size = 0x00010000
+	}
+};
+
+#define NUM_AMD_PARTITIONS ARRAY_SIZE(nettel_amd_partitions)
+
+/****************************************************************************/
+
+#ifdef CONFIG_MTD_CFI_INTELEXT
+
+/*
+ *	Set the Intel flash back to read mode since some old boot
+ *	loaders don't.
+ */
+static int nettel_reboot_notifier(struct notifier_block *nb, unsigned long val, void *v)
+{
+	struct cfi_private *cfi = nettel_intel_map.fldrv_priv;
+	unsigned long b;
+
+	/* Make sure all FLASH chips are put back into read mode */
+	for (b = 0; (b < nettel_intel_partitions[3].size); b += 0x100000) {
+		cfi_send_gen_cmd(0xff, 0x55, b, &nettel_intel_map, cfi,
+			cfi->device_type, NULL);
+	}
+	return(NOTIFY_OK);
+}
+
+static struct notifier_block nettel_notifier_block = {
+	nettel_reboot_notifier, NULL, 0
+};
+
+#endif
+
+/****************************************************************************/
+
+static int __init nettel_init(void)
+{
+	volatile unsigned long *amdpar;
+	unsigned long amdaddr, maxsize;
+	int num_amd_partitions=0;
+#ifdef CONFIG_MTD_CFI_INTELEXT
+	volatile unsigned long *intel0par, *intel1par;
+	unsigned long orig_bootcspar, orig_romcs1par;
+	unsigned long intel0addr, intel0size;
+	unsigned long intel1addr, intel1size;
+	int intelboot, intel0cs, intel1cs;
+	int num_intel_partitions;
+#endif
+	int rc = 0;
+
+	nettel_mmcrp = (void *) ioremap_nocache(0xfffef000, 4096);
+	if (nettel_mmcrp == NULL) {
+		printk("SNAPGEAR: failed to disable MMCR cache??\n");
+		return(-EIO);
+	}
+
+	/* Set CPU clock to be 33.000MHz */
+	*((unsigned char *) (nettel_mmcrp + 0xc64)) = 0x01;
+
+	amdpar = (volatile unsigned long *) (nettel_mmcrp + 0xc4);
+
+#ifdef CONFIG_MTD_CFI_INTELEXT
+	intelboot = 0;
+	intel0cs = SC520_PAR_ROMCS1;
+	intel0par = (volatile unsigned long *) (nettel_mmcrp + 0xc0);
+	intel1cs = SC520_PAR_ROMCS2;
+	intel1par = (volatile unsigned long *) (nettel_mmcrp + 0xbc);
+
+	/*
+	 *	Save the CS settings then ensure ROMCS1 and ROMCS2 are off,
+	 *	otherwise they might clash with where we try to map BOOTCS.
+	 */
+	orig_bootcspar = *amdpar;
+	orig_romcs1par = *intel0par;
+	*intel0par = 0;
+	*intel1par = 0;
+#endif
+
+	/*
+	 *	The first thing to do is determine if we have a separate
+	 *	boot FLASH device. Typically this is a small (1 to 2MB)
+	 *	AMD FLASH part. It seems that device size is about the
+	 *	only way to tell if this is the case...
+	 */
+	amdaddr = 0x20000000;
+	maxsize = AMD_WINDOW_MAXSIZE;
+
+	*amdpar = SC520_PAR(SC520_PAR_BOOTCS, amdaddr, maxsize);
+	__asm__ ("wbinvd");
+
+	nettel_amd_map.phys = amdaddr;
+	nettel_amd_map.virt = ioremap_nocache(amdaddr, maxsize);
+	if (!nettel_amd_map.virt) {
+		printk("SNAPGEAR: failed to ioremap() BOOTCS\n");
+		iounmap(nettel_mmcrp);
+		return(-EIO);
+	}
+	simple_map_init(&nettel_amd_map);
+
+	if ((amd_mtd = do_map_probe("jedec_probe", &nettel_amd_map))) {
+		printk(KERN_NOTICE "SNAPGEAR: AMD flash device size = %dK\n",
+			(int)(amd_mtd->size>>10));
+
+		amd_mtd->owner = THIS_MODULE;
+
+		/* The high BIOS partition is only present for 2MB units */
+		num_amd_partitions = NUM_AMD_PARTITIONS;
+		if (amd_mtd->size < AMD_WINDOW_MAXSIZE)
+			num_amd_partitions--;
+		/* Don't add the partition until after the primary INTEL's */
+
+#ifdef CONFIG_MTD_CFI_INTELEXT
+		/*
+		 *	Map the Intel flash into memory after the AMD
+		 *	It has to start on a multiple of maxsize.
+		 */
+		maxsize = SC520_PAR_TO_SIZE(orig_romcs1par);
+		if (maxsize < (32 * 1024 * 1024))
+			maxsize = (32 * 1024 * 1024);
+		intel0addr = amdaddr + maxsize;
+#endif
+	} else {
+#ifdef CONFIG_MTD_CFI_INTELEXT
+		/* INTEL boot FLASH */
+		intelboot++;
+
+		if (!orig_romcs1par) {
+			intel0cs = SC520_PAR_BOOTCS;
+			intel0par = (volatile unsigned long *)
+				(nettel_mmcrp + 0xc4);
+			intel1cs = SC520_PAR_ROMCS1;
+			intel1par = (volatile unsigned long *)
+				(nettel_mmcrp + 0xc0);
+
+			intel0addr = SC520_PAR_TO_ADDR(orig_bootcspar);
+			maxsize = SC520_PAR_TO_SIZE(orig_bootcspar);
+		} else {
+			/* Kernel base is on ROMCS1, not BOOTCS */
+			intel0cs = SC520_PAR_ROMCS1;
+			intel0par = (volatile unsigned long *)
+				(nettel_mmcrp + 0xc0);
+			intel1cs = SC520_PAR_BOOTCS;
+			intel1par = (volatile unsigned long *)
+				(nettel_mmcrp + 0xc4);
+
+			intel0addr = SC520_PAR_TO_ADDR(orig_romcs1par);
+			maxsize = SC520_PAR_TO_SIZE(orig_romcs1par);
+		}
+
+		/* Destroy useless AMD MTD mapping */
+		amd_mtd = NULL;
+		iounmap(nettel_amd_map.virt);
+		nettel_amd_map.virt = NULL;
+#else
+		/* Only AMD flash supported */
+		rc = -ENXIO;
+		goto out_unmap2;
+#endif
+	}
+
+#ifdef CONFIG_MTD_CFI_INTELEXT
+	/*
+	 *	We have determined the INTEL FLASH configuration, so lets
+	 *	go ahead and probe for them now.
+	 */
+
+	/* Set PAR to the maximum size */
+	if (maxsize < (32 * 1024 * 1024))
+		maxsize = (32 * 1024 * 1024);
+	*intel0par = SC520_PAR(intel0cs, intel0addr, maxsize);
+
+	/* Turn other PAR off so the first probe doesn't find it */
+	*intel1par = 0;
+
+	/* Probe for the size of the first Intel flash */
+	nettel_intel_map.size = maxsize;
+	nettel_intel_map.phys = intel0addr;
+	nettel_intel_map.virt = ioremap_nocache(intel0addr, maxsize);
+	if (!nettel_intel_map.virt) {
+		printk("SNAPGEAR: failed to ioremap() ROMCS1\n");
+		rc = -EIO;
+		goto out_unmap2;
+	}
+	simple_map_init(&nettel_intel_map);
+
+	intel_mtd = do_map_probe("cfi_probe", &nettel_intel_map);
+	if (!intel_mtd) {
+		rc = -ENXIO;
+		goto out_unmap1;
+	}
+
+	/* Set PAR to the detected size */
+	intel0size = intel_mtd->size;
+	*intel0par = SC520_PAR(intel0cs, intel0addr, intel0size);
+
+	/*
+	 *	Map second Intel FLASH right after first. Set its size to the
+	 *	same maxsize used for the first Intel FLASH.
+	 */
+	intel1addr = intel0addr + intel0size;
+	*intel1par = SC520_PAR(intel1cs, intel1addr, maxsize);
+	__asm__ ("wbinvd");
+
+	maxsize += intel0size;
+
+	/* Delete the old map and probe again to do both chips */
+	map_destroy(intel_mtd);
+	intel_mtd = NULL;
+	iounmap(nettel_intel_map.virt);
+
+	nettel_intel_map.size = maxsize;
+	nettel_intel_map.virt = ioremap_nocache(intel0addr, maxsize);
+	if (!nettel_intel_map.virt) {
+		printk("SNAPGEAR: failed to ioremap() ROMCS1/2\n");
+		rc = -EIO;
+		goto out_unmap2;
+	}
+
+	intel_mtd = do_map_probe("cfi_probe", &nettel_intel_map);
+	if (! intel_mtd) {
+		rc = -ENXIO;
+		goto out_unmap1;
+	}
+
+	intel1size = intel_mtd->size - intel0size;
+	if (intel1size > 0) {
+		*intel1par = SC520_PAR(intel1cs, intel1addr, intel1size);
+		__asm__ ("wbinvd");
+	} else {
+		*intel1par = 0;
+	}
+
+	printk(KERN_NOTICE "SNAPGEAR: Intel flash device size = %lldKiB\n",
+	       (unsigned long long)(intel_mtd->size >> 10));
+
+	intel_mtd->owner = THIS_MODULE;
+
+	num_intel_partitions = ARRAY_SIZE(nettel_intel_partitions);
+
+	if (intelboot) {
+		/*
+		 *	Adjust offset and size of last boot partition.
+		 *	Must allow for BIOS region at end of FLASH.
+		 */
+		nettel_intel_partitions[1].size = (intel0size + intel1size) -
+			(1024*1024 + intel_mtd->erasesize);
+		nettel_intel_partitions[3].size = intel0size + intel1size;
+		nettel_intel_partitions[4].offset =
+			(intel0size + intel1size) - intel_mtd->erasesize;
+		nettel_intel_partitions[4].size = intel_mtd->erasesize;
+		nettel_intel_partitions[5].offset =
+			nettel_intel_partitions[4].offset;
+		nettel_intel_partitions[5].size =
+			nettel_intel_partitions[4].size;
+	} else {
+		/* No BIOS regions when AMD boot */
+		num_intel_partitions -= 2;
+	}
+	rc = mtd_device_register(intel_mtd, nettel_intel_partitions,
+				 num_intel_partitions);
+#endif
+
+	if (amd_mtd) {
+		rc = mtd_device_register(amd_mtd, nettel_amd_partitions,
+					 num_amd_partitions);
+	}
+
+#ifdef CONFIG_MTD_CFI_INTELEXT
+	register_reboot_notifier(&nettel_notifier_block);
+#endif
+
+	return(rc);
+
+#ifdef CONFIG_MTD_CFI_INTELEXT
+out_unmap1:
+	iounmap(nettel_intel_map.virt);
+#endif
+
+out_unmap2:
+	iounmap(nettel_mmcrp);
+	iounmap(nettel_amd_map.virt);
+
+	return(rc);
+
+}
+
+/****************************************************************************/
+
+static void __exit nettel_cleanup(void)
+{
+#ifdef CONFIG_MTD_CFI_INTELEXT
+	unregister_reboot_notifier(&nettel_notifier_block);
+#endif
+	if (amd_mtd) {
+		mtd_device_unregister(amd_mtd);
+		map_destroy(amd_mtd);
+	}
+	if (nettel_mmcrp) {
+		iounmap(nettel_mmcrp);
+		nettel_mmcrp = NULL;
+	}
+	if (nettel_amd_map.virt) {
+		iounmap(nettel_amd_map.virt);
+		nettel_amd_map.virt = NULL;
+	}
+#ifdef CONFIG_MTD_CFI_INTELEXT
+	if (intel_mtd) {
+		mtd_device_unregister(intel_mtd);
+		map_destroy(intel_mtd);
+	}
+	if (nettel_intel_map.virt) {
+		iounmap(nettel_intel_map.virt);
+		nettel_intel_map.virt = NULL;
+	}
+#endif
+}
+
+/****************************************************************************/
+
+module_init(nettel_init);
+module_exit(nettel_cleanup);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Greg Ungerer <gerg@snapgear.com>");
+MODULE_DESCRIPTION("SnapGear/SecureEdge FLASH support");
+
+/****************************************************************************/
diff --git a/drivers/mtd/maps/pci.c b/drivers/mtd/maps/pci.c
new file mode 100644
index 000000000..eb0242e0b
--- /dev/null
+++ b/drivers/mtd/maps/pci.c
@@ -0,0 +1,333 @@
+/*
+ *  linux/drivers/mtd/maps/pci.c
+ *
+ *  Copyright (C) 2001 Russell King, All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Generic PCI memory map driver.  We support the following boards:
+ *  - Intel IQ80310 ATU.
+ *  - Intel EBSA285 (blank rom programming mode). Tested working 27/09/2001
+ */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/slab.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+struct map_pci_info;
+
+struct mtd_pci_info {
+	int  (*init)(struct pci_dev *dev, struct map_pci_info *map);
+	void (*exit)(struct pci_dev *dev, struct map_pci_info *map);
+	unsigned long (*translate)(struct map_pci_info *map, unsigned long ofs);
+	const char *map_name;
+};
+
+struct map_pci_info {
+	struct map_info map;
+	void __iomem *base;
+	void (*exit)(struct pci_dev *dev, struct map_pci_info *map);
+	unsigned long (*translate)(struct map_pci_info *map, unsigned long ofs);
+	struct pci_dev *dev;
+};
+
+static map_word mtd_pci_read8(struct map_info *_map, unsigned long ofs)
+{
+	struct map_pci_info *map = (struct map_pci_info *)_map;
+	map_word val;
+	val.x[0]= readb(map->base + map->translate(map, ofs));
+	return val;
+}
+
+static map_word mtd_pci_read32(struct map_info *_map, unsigned long ofs)
+{
+	struct map_pci_info *map = (struct map_pci_info *)_map;
+	map_word val;
+	val.x[0] = readl(map->base + map->translate(map, ofs));
+	return val;
+}
+
+static void mtd_pci_copyfrom(struct map_info *_map, void *to, unsigned long from, ssize_t len)
+{
+	struct map_pci_info *map = (struct map_pci_info *)_map;
+	memcpy_fromio(to, map->base + map->translate(map, from), len);
+}
+
+static void mtd_pci_write8(struct map_info *_map, map_word val, unsigned long ofs)
+{
+	struct map_pci_info *map = (struct map_pci_info *)_map;
+	writeb(val.x[0], map->base + map->translate(map, ofs));
+}
+
+static void mtd_pci_write32(struct map_info *_map, map_word val, unsigned long ofs)
+{
+	struct map_pci_info *map = (struct map_pci_info *)_map;
+	writel(val.x[0], map->base + map->translate(map, ofs));
+}
+
+static void mtd_pci_copyto(struct map_info *_map, unsigned long to, const void *from, ssize_t len)
+{
+	struct map_pci_info *map = (struct map_pci_info *)_map;
+	memcpy_toio(map->base + map->translate(map, to), from, len);
+}
+
+static const struct map_info mtd_pci_map = {
+	.phys =		NO_XIP,
+	.copy_from =	mtd_pci_copyfrom,
+	.copy_to =	mtd_pci_copyto,
+};
+
+/*
+ * Intel IOP80310 Flash driver
+ */
+
+static int
+intel_iq80310_init(struct pci_dev *dev, struct map_pci_info *map)
+{
+	u32 win_base;
+
+	map->map.bankwidth = 1;
+	map->map.read = mtd_pci_read8,
+	map->map.write = mtd_pci_write8,
+
+	map->map.size     = 0x00800000;
+	map->base         = ioremap_nocache(pci_resource_start(dev, 0),
+					    pci_resource_len(dev, 0));
+
+	if (!map->base)
+		return -ENOMEM;
+
+	/*
+	 * We want to base the memory window at Xscale
+	 * bus address 0, not 0x1000.
+	 */
+	pci_read_config_dword(dev, 0x44, &win_base);
+	pci_write_config_dword(dev, 0x44, 0);
+
+	map->map.map_priv_2 = win_base;
+
+	return 0;
+}
+
+static void
+intel_iq80310_exit(struct pci_dev *dev, struct map_pci_info *map)
+{
+	if (map->base)
+		iounmap(map->base);
+	pci_write_config_dword(dev, 0x44, map->map.map_priv_2);
+}
+
+static unsigned long
+intel_iq80310_translate(struct map_pci_info *map, unsigned long ofs)
+{
+	unsigned long page_addr = ofs & 0x00400000;
+
+	/*
+	 * This mundges the flash location so we avoid
+	 * the first 80 bytes (they appear to read nonsense).
+	 */
+	if (page_addr) {
+		writel(0x00000008, map->base + 0x1558);
+		writel(0x00000000, map->base + 0x1550);
+	} else {
+		writel(0x00000007, map->base + 0x1558);
+		writel(0x00800000, map->base + 0x1550);
+		ofs += 0x00800000;
+	}
+
+	return ofs;
+}
+
+static struct mtd_pci_info intel_iq80310_info = {
+	.init =		intel_iq80310_init,
+	.exit =		intel_iq80310_exit,
+	.translate =	intel_iq80310_translate,
+	.map_name =	"cfi_probe",
+};
+
+/*
+ * Intel DC21285 driver
+ */
+
+static int
+intel_dc21285_init(struct pci_dev *dev, struct map_pci_info *map)
+{
+	unsigned long base, len;
+
+	base = pci_resource_start(dev, PCI_ROM_RESOURCE);
+	len  = pci_resource_len(dev, PCI_ROM_RESOURCE);
+
+	if (!len || !base) {
+		/*
+		 * No ROM resource
+		 */
+		base = pci_resource_start(dev, 2);
+		len  = pci_resource_len(dev, 2);
+
+		/*
+		 * We need to re-allocate PCI BAR2 address range to the
+		 * PCI ROM BAR, and disable PCI BAR2.
+		 */
+	} else {
+		/*
+		 * Hmm, if an address was allocated to the ROM resource, but
+		 * not enabled, should we be allocating a new resource for it
+		 * or simply enabling it?
+		 */
+		pci_enable_rom(dev);
+		printk("%s: enabling expansion ROM\n", pci_name(dev));
+	}
+
+	if (!len || !base)
+		return -ENXIO;
+
+	map->map.bankwidth = 4;
+	map->map.read = mtd_pci_read32,
+	map->map.write = mtd_pci_write32,
+	map->map.size     = len;
+	map->base         = ioremap_nocache(base, len);
+
+	if (!map->base)
+		return -ENOMEM;
+
+	return 0;
+}
+
+static void
+intel_dc21285_exit(struct pci_dev *dev, struct map_pci_info *map)
+{
+	if (map->base)
+		iounmap(map->base);
+
+	/*
+	 * We need to undo the PCI BAR2/PCI ROM BAR address alteration.
+	 */
+	pci_disable_rom(dev);
+}
+
+static unsigned long
+intel_dc21285_translate(struct map_pci_info *map, unsigned long ofs)
+{
+	return ofs & 0x00ffffc0 ? ofs : (ofs ^ (1 << 5));
+}
+
+static struct mtd_pci_info intel_dc21285_info = {
+	.init =		intel_dc21285_init,
+	.exit =		intel_dc21285_exit,
+	.translate =	intel_dc21285_translate,
+	.map_name =	"jedec_probe",
+};
+
+/*
+ * PCI device ID table
+ */
+
+static struct pci_device_id mtd_pci_ids[] = {
+	{
+		.vendor =	PCI_VENDOR_ID_INTEL,
+		.device =	0x530d,
+		.subvendor =	PCI_ANY_ID,
+		.subdevice =	PCI_ANY_ID,
+		.class =	PCI_CLASS_MEMORY_OTHER << 8,
+		.class_mask =	0xffff00,
+		.driver_data =	(unsigned long)&intel_iq80310_info,
+	},
+	{
+		.vendor =	PCI_VENDOR_ID_DEC,
+		.device =	PCI_DEVICE_ID_DEC_21285,
+		.subvendor =	0,	/* DC21285 defaults to 0 on reset */
+		.subdevice =	0,	/* DC21285 defaults to 0 on reset */
+		.driver_data =	(unsigned long)&intel_dc21285_info,
+	},
+	{ 0, }
+};
+
+/*
+ * Generic code follows.
+ */
+
+static int mtd_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	struct mtd_pci_info *info = (struct mtd_pci_info *)id->driver_data;
+	struct map_pci_info *map = NULL;
+	struct mtd_info *mtd = NULL;
+	int err;
+
+	err = pci_enable_device(dev);
+	if (err)
+		goto out;
+
+	err = pci_request_regions(dev, "pci mtd");
+	if (err)
+		goto out;
+
+	map = kmalloc(sizeof(*map), GFP_KERNEL);
+	err = -ENOMEM;
+	if (!map)
+		goto release;
+
+	map->map       = mtd_pci_map;
+	map->map.name  = pci_name(dev);
+	map->dev       = dev;
+	map->exit      = info->exit;
+	map->translate = info->translate;
+
+	err = info->init(dev, map);
+	if (err)
+		goto release;
+
+	mtd = do_map_probe(info->map_name, &map->map);
+	err = -ENODEV;
+	if (!mtd)
+		goto release;
+
+	mtd->owner = THIS_MODULE;
+	mtd_device_register(mtd, NULL, 0);
+
+	pci_set_drvdata(dev, mtd);
+
+	return 0;
+
+release:
+	if (map) {
+		map->exit(dev, map);
+		kfree(map);
+	}
+
+	pci_release_regions(dev);
+out:
+	return err;
+}
+
+static void mtd_pci_remove(struct pci_dev *dev)
+{
+	struct mtd_info *mtd = pci_get_drvdata(dev);
+	struct map_pci_info *map = mtd->priv;
+
+	mtd_device_unregister(mtd);
+	map_destroy(mtd);
+	map->exit(dev, map);
+	kfree(map);
+
+	pci_release_regions(dev);
+}
+
+static struct pci_driver mtd_pci_driver = {
+	.name =		"MTD PCI",
+	.probe =	mtd_pci_probe,
+	.remove =	mtd_pci_remove,
+	.id_table =	mtd_pci_ids,
+};
+
+module_pci_driver(mtd_pci_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
+MODULE_DESCRIPTION("Generic PCI map driver");
+MODULE_DEVICE_TABLE(pci, mtd_pci_ids);
diff --git a/drivers/mtd/maps/pcmciamtd.c b/drivers/mtd/maps/pcmciamtd.c
new file mode 100644
index 000000000..af747af5e
--- /dev/null
+++ b/drivers/mtd/maps/pcmciamtd.c
@@ -0,0 +1,753 @@
+/*
+ * pcmciamtd.c - MTD driver for PCMCIA flash memory cards
+ *
+ * Author: Simon Evans <spse@secret.org.uk>
+ *
+ * Copyright (C) 2002 Simon Evans
+ *
+ * Licence: GPL
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <asm/io.h>
+
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ds.h>
+
+#include <linux/mtd/map.h>
+#include <linux/mtd/mtd.h>
+
+#define info(format, arg...) printk(KERN_INFO "pcmciamtd: " format "\n" , ## arg)
+
+#define DRIVER_DESC	"PCMCIA Flash memory card driver"
+
+/* Size of the PCMCIA address space: 26 bits = 64 MB */
+#define MAX_PCMCIA_ADDR	0x4000000
+
+struct pcmciamtd_dev {
+	struct pcmcia_device	*p_dev;
+	caddr_t		win_base;	/* ioremapped address of PCMCIA window */
+	unsigned int	win_size;	/* size of window */
+	unsigned int	offset;		/* offset into card the window currently points at */
+	struct map_info	pcmcia_map;
+	struct mtd_info	*mtd_info;
+	int		vpp;
+	char		mtd_name[sizeof(struct cistpl_vers_1_t)];
+};
+
+
+/* Module parameters */
+
+/* 2 = do 16-bit transfers, 1 = do 8-bit transfers */
+static int bankwidth = 2;
+
+/* Speed of memory accesses, in ns */
+static int mem_speed;
+
+/* Force the size of an SRAM card */
+static int force_size;
+
+/* Force Vpp */
+static int vpp;
+
+/* Set Vpp */
+static int setvpp;
+
+/* Force card to be treated as FLASH, ROM or RAM */
+static int mem_type;
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Simon Evans <spse@secret.org.uk>");
+MODULE_DESCRIPTION(DRIVER_DESC);
+module_param(bankwidth, int, 0);
+MODULE_PARM_DESC(bankwidth, "Set bankwidth (1=8 bit, 2=16 bit, default=2)");
+module_param(mem_speed, int, 0);
+MODULE_PARM_DESC(mem_speed, "Set memory access speed in ns");
+module_param(force_size, int, 0);
+MODULE_PARM_DESC(force_size, "Force size of card in MiB (1-64)");
+module_param(setvpp, int, 0);
+MODULE_PARM_DESC(setvpp, "Set Vpp (0=Never, 1=On writes, 2=Always on, default=0)");
+module_param(vpp, int, 0);
+MODULE_PARM_DESC(vpp, "Vpp value in 1/10ths eg 33=3.3V 120=12V (Dangerous)");
+module_param(mem_type, int, 0);
+MODULE_PARM_DESC(mem_type, "Set Memory type (0=Flash, 1=RAM, 2=ROM, default=0)");
+
+
+/* read/write{8,16} copy_{from,to} routines with window remapping
+ * to access whole card
+ */
+static caddr_t remap_window(struct map_info *map, unsigned long to)
+{
+	struct pcmciamtd_dev *dev = (struct pcmciamtd_dev *)map->map_priv_1;
+	struct resource *win = (struct resource *) map->map_priv_2;
+	unsigned int offset;
+	int ret;
+
+	if (!pcmcia_dev_present(dev->p_dev)) {
+		pr_debug("device removed\n");
+		return NULL;
+	}
+
+	offset = to & ~(dev->win_size-1);
+	if (offset != dev->offset) {
+		pr_debug("Remapping window from 0x%8.8x to 0x%8.8x\n",
+		      dev->offset, offset);
+		ret = pcmcia_map_mem_page(dev->p_dev, win, offset);
+		if (ret != 0)
+			return NULL;
+		dev->offset = offset;
+	}
+	return dev->win_base + (to & (dev->win_size-1));
+}
+
+
+static map_word pcmcia_read8_remap(struct map_info *map, unsigned long ofs)
+{
+	caddr_t addr;
+	map_word d = {{0}};
+
+	addr = remap_window(map, ofs);
+	if(!addr)
+		return d;
+
+	d.x[0] = readb(addr);
+	pr_debug("ofs = 0x%08lx (%p) data = 0x%02lx\n", ofs, addr, d.x[0]);
+	return d;
+}
+
+
+static map_word pcmcia_read16_remap(struct map_info *map, unsigned long ofs)
+{
+	caddr_t addr;
+	map_word d = {{0}};
+
+	addr = remap_window(map, ofs);
+	if(!addr)
+		return d;
+
+	d.x[0] = readw(addr);
+	pr_debug("ofs = 0x%08lx (%p) data = 0x%04lx\n", ofs, addr, d.x[0]);
+	return d;
+}
+
+
+static void pcmcia_copy_from_remap(struct map_info *map, void *to, unsigned long from, ssize_t len)
+{
+	struct pcmciamtd_dev *dev = (struct pcmciamtd_dev *)map->map_priv_1;
+	unsigned long win_size = dev->win_size;
+
+	pr_debug("to = %p from = %lu len = %zd\n", to, from, len);
+	while(len) {
+		int toread = win_size - (from & (win_size-1));
+		caddr_t addr;
+
+		if(toread > len)
+			toread = len;
+
+		addr = remap_window(map, from);
+		if(!addr)
+			return;
+
+		pr_debug("memcpy from %p to %p len = %d\n", addr, to, toread);
+		memcpy_fromio(to, addr, toread);
+		len -= toread;
+		to += toread;
+		from += toread;
+	}
+}
+
+
+static void pcmcia_write8_remap(struct map_info *map, map_word d, unsigned long adr)
+{
+	caddr_t addr = remap_window(map, adr);
+
+	if(!addr)
+		return;
+
+	pr_debug("adr = 0x%08lx (%p)  data = 0x%02lx\n", adr, addr, d.x[0]);
+	writeb(d.x[0], addr);
+}
+
+
+static void pcmcia_write16_remap(struct map_info *map, map_word d, unsigned long adr)
+{
+	caddr_t addr = remap_window(map, adr);
+	if(!addr)
+		return;
+
+	pr_debug("adr = 0x%08lx (%p)  data = 0x%04lx\n", adr, addr, d.x[0]);
+	writew(d.x[0], addr);
+}
+
+
+static void pcmcia_copy_to_remap(struct map_info *map, unsigned long to, const void *from, ssize_t len)
+{
+	struct pcmciamtd_dev *dev = (struct pcmciamtd_dev *)map->map_priv_1;
+	unsigned long win_size = dev->win_size;
+
+	pr_debug("to = %lu from = %p len = %zd\n", to, from, len);
+	while(len) {
+		int towrite = win_size - (to & (win_size-1));
+		caddr_t addr;
+
+		if(towrite > len)
+			towrite = len;
+
+		addr = remap_window(map, to);
+		if(!addr)
+			return;
+
+		pr_debug("memcpy from %p to %p len = %d\n", from, addr, towrite);
+		memcpy_toio(addr, from, towrite);
+		len -= towrite;
+		to += towrite;
+		from += towrite;
+	}
+}
+
+
+/* read/write{8,16} copy_{from,to} routines with direct access */
+
+#define DEV_REMOVED(x)  (!(pcmcia_dev_present(((struct pcmciamtd_dev *)map->map_priv_1)->p_dev)))
+
+static map_word pcmcia_read8(struct map_info *map, unsigned long ofs)
+{
+	caddr_t win_base = (caddr_t)map->map_priv_2;
+	map_word d = {{0}};
+
+	if(DEV_REMOVED(map))
+		return d;
+
+	d.x[0] = readb(win_base + ofs);
+	pr_debug("ofs = 0x%08lx (%p) data = 0x%02lx\n",
+	      ofs, win_base + ofs, d.x[0]);
+	return d;
+}
+
+
+static map_word pcmcia_read16(struct map_info *map, unsigned long ofs)
+{
+	caddr_t win_base = (caddr_t)map->map_priv_2;
+	map_word d = {{0}};
+
+	if(DEV_REMOVED(map))
+		return d;
+
+	d.x[0] = readw(win_base + ofs);
+	pr_debug("ofs = 0x%08lx (%p) data = 0x%04lx\n",
+	      ofs, win_base + ofs, d.x[0]);
+	return d;
+}
+
+
+static void pcmcia_copy_from(struct map_info *map, void *to, unsigned long from, ssize_t len)
+{
+	caddr_t win_base = (caddr_t)map->map_priv_2;
+
+	if(DEV_REMOVED(map))
+		return;
+
+	pr_debug("to = %p from = %lu len = %zd\n", to, from, len);
+	memcpy_fromio(to, win_base + from, len);
+}
+
+
+static void pcmcia_write8(struct map_info *map, map_word d, unsigned long adr)
+{
+	caddr_t win_base = (caddr_t)map->map_priv_2;
+
+	if(DEV_REMOVED(map))
+		return;
+
+	pr_debug("adr = 0x%08lx (%p)  data = 0x%02lx\n",
+	      adr, win_base + adr, d.x[0]);
+	writeb(d.x[0], win_base + adr);
+}
+
+
+static void pcmcia_write16(struct map_info *map, map_word d, unsigned long adr)
+{
+	caddr_t win_base = (caddr_t)map->map_priv_2;
+
+	if(DEV_REMOVED(map))
+		return;
+
+	pr_debug("adr = 0x%08lx (%p)  data = 0x%04lx\n",
+	      adr, win_base + adr, d.x[0]);
+	writew(d.x[0], win_base + adr);
+}
+
+
+static void pcmcia_copy_to(struct map_info *map, unsigned long to, const void *from, ssize_t len)
+{
+	caddr_t win_base = (caddr_t)map->map_priv_2;
+
+	if(DEV_REMOVED(map))
+		return;
+
+	pr_debug("to = %lu from = %p len = %zd\n", to, from, len);
+	memcpy_toio(win_base + to, from, len);
+}
+
+
+static DEFINE_SPINLOCK(pcmcia_vpp_lock);
+static int pcmcia_vpp_refcnt;
+static void pcmciamtd_set_vpp(struct map_info *map, int on)
+{
+	struct pcmciamtd_dev *dev = (struct pcmciamtd_dev *)map->map_priv_1;
+	struct pcmcia_device *link = dev->p_dev;
+	unsigned long flags;
+
+	pr_debug("dev = %p on = %d vpp = %d\n\n", dev, on, dev->vpp);
+	spin_lock_irqsave(&pcmcia_vpp_lock, flags);
+	if (on) {
+		if (++pcmcia_vpp_refcnt == 1)   /* first nested 'on' */
+			pcmcia_fixup_vpp(link, dev->vpp);
+	} else {
+		if (--pcmcia_vpp_refcnt == 0)   /* last nested 'off' */
+			pcmcia_fixup_vpp(link, 0);
+	}
+	spin_unlock_irqrestore(&pcmcia_vpp_lock, flags);
+}
+
+
+static void pcmciamtd_release(struct pcmcia_device *link)
+{
+	struct pcmciamtd_dev *dev = link->priv;
+
+	pr_debug("link = 0x%p\n", link);
+
+	if (link->resource[2]->end) {
+		if(dev->win_base) {
+			iounmap(dev->win_base);
+			dev->win_base = NULL;
+		}
+	}
+	pcmcia_disable_device(link);
+}
+
+
+static int pcmciamtd_cistpl_format(struct pcmcia_device *p_dev,
+				tuple_t *tuple,
+				void *priv_data)
+{
+	cisparse_t parse;
+
+	if (!pcmcia_parse_tuple(tuple, &parse)) {
+		cistpl_format_t *t = &parse.format;
+		(void)t; /* Shut up, gcc */
+		pr_debug("Format type: %u, Error Detection: %u, offset = %u, length =%u\n",
+			t->type, t->edc, t->offset, t->length);
+	}
+	return -ENOSPC;
+}
+
+static int pcmciamtd_cistpl_jedec(struct pcmcia_device *p_dev,
+				tuple_t *tuple,
+				void *priv_data)
+{
+	cisparse_t parse;
+	int i;
+
+	if (!pcmcia_parse_tuple(tuple, &parse)) {
+		cistpl_jedec_t *t = &parse.jedec;
+		for (i = 0; i < t->nid; i++)
+			pr_debug("JEDEC: 0x%02x 0x%02x\n",
+			      t->id[i].mfr, t->id[i].info);
+	}
+	return -ENOSPC;
+}
+
+static int pcmciamtd_cistpl_device(struct pcmcia_device *p_dev,
+				tuple_t *tuple,
+				void *priv_data)
+{
+	struct pcmciamtd_dev *dev = priv_data;
+	cisparse_t parse;
+	cistpl_device_t *t = &parse.device;
+	int i;
+
+	if (pcmcia_parse_tuple(tuple, &parse))
+		return -EINVAL;
+
+	pr_debug("Common memory:\n");
+	dev->pcmcia_map.size = t->dev[0].size;
+	/* from here on: DEBUG only */
+	for (i = 0; i < t->ndev; i++) {
+		pr_debug("Region %d, type = %u\n", i, t->dev[i].type);
+		pr_debug("Region %d, wp = %u\n", i, t->dev[i].wp);
+		pr_debug("Region %d, speed = %u ns\n", i, t->dev[i].speed);
+		pr_debug("Region %d, size = %u bytes\n", i, t->dev[i].size);
+	}
+	return 0;
+}
+
+static int pcmciamtd_cistpl_geo(struct pcmcia_device *p_dev,
+				tuple_t *tuple,
+				void *priv_data)
+{
+	struct pcmciamtd_dev *dev = priv_data;
+	cisparse_t parse;
+	cistpl_device_geo_t *t = &parse.device_geo;
+	int i;
+
+	if (pcmcia_parse_tuple(tuple, &parse))
+		return -EINVAL;
+
+	dev->pcmcia_map.bankwidth = t->geo[0].buswidth;
+	/* from here on: DEBUG only */
+	for (i = 0; i < t->ngeo; i++) {
+		pr_debug("region: %d bankwidth = %u\n", i, t->geo[i].buswidth);
+		pr_debug("region: %d erase_block = %u\n", i, t->geo[i].erase_block);
+		pr_debug("region: %d read_block = %u\n", i, t->geo[i].read_block);
+		pr_debug("region: %d write_block = %u\n", i, t->geo[i].write_block);
+		pr_debug("region: %d partition = %u\n", i, t->geo[i].partition);
+		pr_debug("region: %d interleave = %u\n", i, t->geo[i].interleave);
+	}
+	return 0;
+}
+
+
+static void card_settings(struct pcmciamtd_dev *dev, struct pcmcia_device *p_dev, int *new_name)
+{
+	int i;
+
+	if (p_dev->prod_id[0]) {
+		dev->mtd_name[0] = '\0';
+		for (i = 0; i < 4; i++) {
+			if (i)
+				strcat(dev->mtd_name, " ");
+			if (p_dev->prod_id[i])
+				strcat(dev->mtd_name, p_dev->prod_id[i]);
+		}
+		pr_debug("Found name: %s\n", dev->mtd_name);
+	}
+
+	pcmcia_loop_tuple(p_dev, CISTPL_FORMAT, pcmciamtd_cistpl_format, NULL);
+	pcmcia_loop_tuple(p_dev, CISTPL_JEDEC_C, pcmciamtd_cistpl_jedec, NULL);
+	pcmcia_loop_tuple(p_dev, CISTPL_DEVICE, pcmciamtd_cistpl_device, dev);
+	pcmcia_loop_tuple(p_dev, CISTPL_DEVICE_GEO, pcmciamtd_cistpl_geo, dev);
+
+	if(!dev->pcmcia_map.size)
+		dev->pcmcia_map.size = MAX_PCMCIA_ADDR;
+
+	if(!dev->pcmcia_map.bankwidth)
+		dev->pcmcia_map.bankwidth = 2;
+
+	if(force_size) {
+		dev->pcmcia_map.size = force_size << 20;
+		pr_debug("size forced to %dM\n", force_size);
+	}
+
+	if(bankwidth) {
+		dev->pcmcia_map.bankwidth = bankwidth;
+		pr_debug("bankwidth forced to %d\n", bankwidth);
+	}
+
+	dev->pcmcia_map.name = dev->mtd_name;
+	if(!dev->mtd_name[0]) {
+		strcpy(dev->mtd_name, "PCMCIA Memory card");
+		*new_name = 1;
+	}
+
+	pr_debug("Device: Size: %lu Width:%d Name: %s\n",
+	      dev->pcmcia_map.size,
+	      dev->pcmcia_map.bankwidth << 3, dev->mtd_name);
+}
+
+
+static int pcmciamtd_config(struct pcmcia_device *link)
+{
+	struct pcmciamtd_dev *dev = link->priv;
+	struct mtd_info *mtd = NULL;
+	int ret;
+	int i, j = 0;
+	static char *probes[] = { "jedec_probe", "cfi_probe" };
+	int new_name = 0;
+
+	pr_debug("link=0x%p\n", link);
+
+	card_settings(dev, link, &new_name);
+
+	dev->pcmcia_map.phys = NO_XIP;
+	dev->pcmcia_map.copy_from = pcmcia_copy_from_remap;
+	dev->pcmcia_map.copy_to = pcmcia_copy_to_remap;
+	if (dev->pcmcia_map.bankwidth == 1) {
+		dev->pcmcia_map.read = pcmcia_read8_remap;
+		dev->pcmcia_map.write = pcmcia_write8_remap;
+	} else {
+		dev->pcmcia_map.read = pcmcia_read16_remap;
+		dev->pcmcia_map.write = pcmcia_write16_remap;
+	}
+	if(setvpp == 1)
+		dev->pcmcia_map.set_vpp = pcmciamtd_set_vpp;
+
+	/* Request a memory window for PCMCIA. Some architeures can map windows
+	 * up to the maximum that PCMCIA can support (64MiB) - this is ideal and
+	 * we aim for a window the size of the whole card - otherwise we try
+	 * smaller windows until we succeed
+	 */
+
+	link->resource[2]->flags |=  WIN_MEMORY_TYPE_CM | WIN_ENABLE;
+	link->resource[2]->flags |= (dev->pcmcia_map.bankwidth == 1) ?
+					WIN_DATA_WIDTH_8 : WIN_DATA_WIDTH_16;
+	link->resource[2]->start = 0;
+	link->resource[2]->end = (force_size) ? force_size << 20 :
+					MAX_PCMCIA_ADDR;
+	dev->win_size = 0;
+
+	do {
+		int ret;
+		pr_debug("requesting window with size = %luKiB memspeed = %d\n",
+			(unsigned long) resource_size(link->resource[2]) >> 10,
+			mem_speed);
+		ret = pcmcia_request_window(link, link->resource[2], mem_speed);
+		pr_debug("ret = %d dev->win_size = %d\n", ret, dev->win_size);
+		if(ret) {
+			j++;
+			link->resource[2]->start = 0;
+			link->resource[2]->end = (force_size) ?
+					force_size << 20 : MAX_PCMCIA_ADDR;
+			link->resource[2]->end >>= j;
+		} else {
+			pr_debug("Got window of size %luKiB\n", (unsigned long)
+				resource_size(link->resource[2]) >> 10);
+			dev->win_size = resource_size(link->resource[2]);
+			break;
+		}
+	} while (link->resource[2]->end >= 0x1000);
+
+	pr_debug("dev->win_size = %d\n", dev->win_size);
+
+	if(!dev->win_size) {
+		dev_err(&dev->p_dev->dev, "Cannot allocate memory window\n");
+		pcmciamtd_release(link);
+		return -ENODEV;
+	}
+	pr_debug("Allocated a window of %dKiB\n", dev->win_size >> 10);
+
+	/* Get write protect status */
+	dev->win_base = ioremap(link->resource[2]->start,
+				resource_size(link->resource[2]));
+	if(!dev->win_base) {
+		dev_err(&dev->p_dev->dev, "ioremap(%pR) failed\n",
+			link->resource[2]);
+		pcmciamtd_release(link);
+		return -ENODEV;
+	}
+	pr_debug("mapped window dev = %p @ %pR, base = %p\n",
+	      dev, link->resource[2], dev->win_base);
+
+	dev->offset = 0;
+	dev->pcmcia_map.map_priv_1 = (unsigned long)dev;
+	dev->pcmcia_map.map_priv_2 = (unsigned long)link->resource[2];
+
+	dev->vpp = (vpp) ? vpp : link->socket->socket.Vpp;
+	if(setvpp == 2) {
+		link->vpp = dev->vpp;
+	} else {
+		link->vpp = 0;
+	}
+
+	link->config_index = 0;
+	pr_debug("Setting Configuration\n");
+	ret = pcmcia_enable_device(link);
+	if (ret != 0) {
+		if (dev->win_base) {
+			iounmap(dev->win_base);
+			dev->win_base = NULL;
+		}
+		return -ENODEV;
+	}
+
+	if(mem_type == 1) {
+		mtd = do_map_probe("map_ram", &dev->pcmcia_map);
+	} else if(mem_type == 2) {
+		mtd = do_map_probe("map_rom", &dev->pcmcia_map);
+	} else {
+		for(i = 0; i < ARRAY_SIZE(probes); i++) {
+			pr_debug("Trying %s\n", probes[i]);
+			mtd = do_map_probe(probes[i], &dev->pcmcia_map);
+			if(mtd)
+				break;
+
+			pr_debug("FAILED: %s\n", probes[i]);
+		}
+	}
+
+	if(!mtd) {
+		pr_debug("Can not find an MTD\n");
+		pcmciamtd_release(link);
+		return -ENODEV;
+	}
+
+	dev->mtd_info = mtd;
+	mtd->owner = THIS_MODULE;
+
+	if(new_name) {
+		int size = 0;
+		char unit = ' ';
+		/* Since we are using a default name, make it better by adding
+		 * in the size
+		 */
+		if(mtd->size < 1048576) { /* <1MiB in size, show size in KiB */
+			size = mtd->size >> 10;
+			unit = 'K';
+		} else {
+			size = mtd->size >> 20;
+			unit = 'M';
+		}
+		snprintf(dev->mtd_name, sizeof(dev->mtd_name), "%d%ciB %s", size, unit, "PCMCIA Memory card");
+	}
+
+	/* If the memory found is fits completely into the mapped PCMCIA window,
+	   use the faster non-remapping read/write functions */
+	if(mtd->size <= dev->win_size) {
+		pr_debug("Using non remapping memory functions\n");
+		dev->pcmcia_map.map_priv_2 = (unsigned long)dev->win_base;
+		if (dev->pcmcia_map.bankwidth == 1) {
+			dev->pcmcia_map.read = pcmcia_read8;
+			dev->pcmcia_map.write = pcmcia_write8;
+		} else {
+			dev->pcmcia_map.read = pcmcia_read16;
+			dev->pcmcia_map.write = pcmcia_write16;
+		}
+		dev->pcmcia_map.copy_from = pcmcia_copy_from;
+		dev->pcmcia_map.copy_to = pcmcia_copy_to;
+	}
+
+	if (mtd_device_register(mtd, NULL, 0)) {
+		map_destroy(mtd);
+		dev->mtd_info = NULL;
+		dev_err(&dev->p_dev->dev,
+			"Could not register the MTD device\n");
+		pcmciamtd_release(link);
+		return -ENODEV;
+	}
+	dev_info(&dev->p_dev->dev, "mtd%d: %s\n", mtd->index, mtd->name);
+	return 0;
+}
+
+
+static int pcmciamtd_suspend(struct pcmcia_device *dev)
+{
+	pr_debug("EVENT_PM_RESUME\n");
+
+	/* get_lock(link); */
+
+	return 0;
+}
+
+static int pcmciamtd_resume(struct pcmcia_device *dev)
+{
+	pr_debug("EVENT_PM_SUSPEND\n");
+
+	/* free_lock(link); */
+
+	return 0;
+}
+
+
+static void pcmciamtd_detach(struct pcmcia_device *link)
+{
+	struct pcmciamtd_dev *dev = link->priv;
+
+	pr_debug("link=0x%p\n", link);
+
+	if(dev->mtd_info) {
+		mtd_device_unregister(dev->mtd_info);
+		dev_info(&dev->p_dev->dev, "mtd%d: Removing\n",
+			 dev->mtd_info->index);
+		map_destroy(dev->mtd_info);
+	}
+
+	pcmciamtd_release(link);
+}
+
+
+static int pcmciamtd_probe(struct pcmcia_device *link)
+{
+	struct pcmciamtd_dev *dev;
+
+	/* Create new memory card device */
+	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+	if (!dev) return -ENOMEM;
+	pr_debug("dev=0x%p\n", dev);
+
+	dev->p_dev = link;
+	link->priv = dev;
+
+	return pcmciamtd_config(link);
+}
+
+static const struct pcmcia_device_id pcmciamtd_ids[] = {
+	PCMCIA_DEVICE_FUNC_ID(1),
+	PCMCIA_DEVICE_PROD_ID123("IO DATA", "PCS-2M", "2MB SRAM", 0x547e66dc, 0x1fed36cd, 0x36eadd21),
+	PCMCIA_DEVICE_PROD_ID12("IBM", "2MB SRAM", 0xb569a6e5, 0x36eadd21),
+	PCMCIA_DEVICE_PROD_ID12("IBM", "4MB FLASH", 0xb569a6e5, 0x8bc54d2a),
+	PCMCIA_DEVICE_PROD_ID12("IBM", "8MB FLASH", 0xb569a6e5, 0x6df1be3e),
+	PCMCIA_DEVICE_PROD_ID12("Intel", "S2E20SW", 0x816cc815, 0xd14c9dcf),
+	PCMCIA_DEVICE_PROD_ID12("Intel", "S2E8 SW", 0x816cc815, 0xa2d7dedb),
+	PCMCIA_DEVICE_PROD_ID12("intel", "SERIES2-02 ", 0x40ade711, 0x145cea5c),
+	PCMCIA_DEVICE_PROD_ID12("intel", "SERIES2-04 ", 0x40ade711, 0x42064dda),
+	PCMCIA_DEVICE_PROD_ID12("intel", "SERIES2-20 ", 0x40ade711, 0x25ee5cb0),
+	PCMCIA_DEVICE_PROD_ID12("intel", "VALUE SERIES 100 ", 0x40ade711, 0xdf8506d8),
+	PCMCIA_DEVICE_PROD_ID12("KINGMAX TECHNOLOGY INC.", "SRAM 256K Bytes", 0x54d0c69c, 0xad12c29c),
+	PCMCIA_DEVICE_PROD_ID12("Maxtor", "MAXFL MobileMax Flash Memory Card", 0xb68968c8, 0x2dfb47b0),
+	PCMCIA_DEVICE_PROD_ID123("M-Systems", "M-SYS Flash Memory Card", "(c) M-Systems", 0x7ed2ad87, 0x675dc3fb, 0x7aef3965),
+	PCMCIA_DEVICE_PROD_ID12("PRETEC", "  2MB SRAM CARD", 0xebf91155, 0x805360ca),
+	PCMCIA_DEVICE_PROD_ID12("SEIKO EPSON", "WWB101EN20", 0xf9876baf, 0xad0b207b),
+	PCMCIA_DEVICE_PROD_ID12("SEIKO EPSON", "WWB513EN20", 0xf9876baf, 0xe8d884ad),
+	PCMCIA_DEVICE_PROD_ID12("SMART Modular Technologies", " 4MB FLASH Card", 0x96fd8277, 0x737a5b05),
+	PCMCIA_DEVICE_PROD_ID12("Starfish, Inc.", "REX-3000", 0x05ddca47, 0xe7d67bca),
+	PCMCIA_DEVICE_PROD_ID12("Starfish, Inc.", "REX-4100", 0x05ddca47, 0x7bc32944),
+	/* the following was commented out in pcmcia-cs-3.2.7 */
+	/* PCMCIA_DEVICE_PROD_ID12("RATOC Systems,Inc.", "SmartMedia ADAPTER PC Card", 0xf4a2fefe, 0x5885b2ae), */
+#ifdef CONFIG_MTD_PCMCIA_ANONYMOUS
+	{ .match_flags = PCMCIA_DEV_ID_MATCH_ANONYMOUS, },
+#endif
+	PCMCIA_DEVICE_NULL
+};
+MODULE_DEVICE_TABLE(pcmcia, pcmciamtd_ids);
+
+static struct pcmcia_driver pcmciamtd_driver = {
+	.name		= "pcmciamtd",
+	.probe		= pcmciamtd_probe,
+	.remove		= pcmciamtd_detach,
+	.owner		= THIS_MODULE,
+	.id_table	= pcmciamtd_ids,
+	.suspend	= pcmciamtd_suspend,
+	.resume		= pcmciamtd_resume,
+};
+
+
+static int __init init_pcmciamtd(void)
+{
+	if(bankwidth && bankwidth != 1 && bankwidth != 2) {
+		info("bad bankwidth (%d), using default", bankwidth);
+		bankwidth = 2;
+	}
+	if(force_size && (force_size < 1 || force_size > 64)) {
+		info("bad force_size (%d), using default", force_size);
+		force_size = 0;
+	}
+	if(mem_type && mem_type != 1 && mem_type != 2) {
+		info("bad mem_type (%d), using default", mem_type);
+		mem_type = 0;
+	}
+	return pcmcia_register_driver(&pcmciamtd_driver);
+}
+
+
+static void __exit exit_pcmciamtd(void)
+{
+	pr_debug(DRIVER_DESC " unloading");
+	pcmcia_unregister_driver(&pcmciamtd_driver);
+}
+
+module_init(init_pcmciamtd);
+module_exit(exit_pcmciamtd);
diff --git a/drivers/mtd/maps/physmap.c b/drivers/mtd/maps/physmap.c
new file mode 100644
index 000000000..4305fd607
--- /dev/null
+++ b/drivers/mtd/maps/physmap.c
@@ -0,0 +1,281 @@
+/*
+ * Normal mappings of chips in physical memory
+ *
+ * Copyright (C) 2003 MontaVista Software Inc.
+ * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
+ *
+ * 031022 - [jsun] add run-time configure and partition setup
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/mtd/concat.h>
+#include <linux/io.h>
+
+#define MAX_RESOURCES		4
+
+struct physmap_flash_info {
+	struct mtd_info		*mtd[MAX_RESOURCES];
+	struct mtd_info		*cmtd;
+	struct map_info		map[MAX_RESOURCES];
+	spinlock_t		vpp_lock;
+	int			vpp_refcnt;
+};
+
+static int physmap_flash_remove(struct platform_device *dev)
+{
+	struct physmap_flash_info *info;
+	struct physmap_flash_data *physmap_data;
+	int i;
+
+	info = platform_get_drvdata(dev);
+	if (info == NULL)
+		return 0;
+
+	physmap_data = dev_get_platdata(&dev->dev);
+
+	if (info->cmtd) {
+		mtd_device_unregister(info->cmtd);
+		if (info->cmtd != info->mtd[0])
+			mtd_concat_destroy(info->cmtd);
+	}
+
+	for (i = 0; i < MAX_RESOURCES; i++) {
+		if (info->mtd[i] != NULL)
+			map_destroy(info->mtd[i]);
+	}
+
+	if (physmap_data->exit)
+		physmap_data->exit(dev);
+
+	return 0;
+}
+
+static void physmap_set_vpp(struct map_info *map, int state)
+{
+	struct platform_device *pdev;
+	struct physmap_flash_data *physmap_data;
+	struct physmap_flash_info *info;
+	unsigned long flags;
+
+	pdev = (struct platform_device *)map->map_priv_1;
+	physmap_data = dev_get_platdata(&pdev->dev);
+
+	if (!physmap_data->set_vpp)
+		return;
+
+	info = platform_get_drvdata(pdev);
+
+	spin_lock_irqsave(&info->vpp_lock, flags);
+	if (state) {
+		if (++info->vpp_refcnt == 1)    /* first nested 'on' */
+			physmap_data->set_vpp(pdev, 1);
+	} else {
+		if (--info->vpp_refcnt == 0)    /* last nested 'off' */
+			physmap_data->set_vpp(pdev, 0);
+	}
+	spin_unlock_irqrestore(&info->vpp_lock, flags);
+}
+
+static const char * const rom_probe_types[] = {
+	"cfi_probe", "jedec_probe", "qinfo_probe", "map_rom", NULL };
+
+static const char * const part_probe_types[] = {
+	"cmdlinepart", "RedBoot", "afs", NULL };
+
+static int physmap_flash_probe(struct platform_device *dev)
+{
+	struct physmap_flash_data *physmap_data;
+	struct physmap_flash_info *info;
+	const char * const *probe_type;
+	const char * const *part_types;
+	int err = 0;
+	int i;
+	int devices_found = 0;
+
+	physmap_data = dev_get_platdata(&dev->dev);
+	if (physmap_data == NULL)
+		return -ENODEV;
+
+	info = devm_kzalloc(&dev->dev, sizeof(struct physmap_flash_info),
+			    GFP_KERNEL);
+	if (info == NULL) {
+		err = -ENOMEM;
+		goto err_out;
+	}
+
+	if (physmap_data->init) {
+		err = physmap_data->init(dev);
+		if (err)
+			goto err_out;
+	}
+
+	platform_set_drvdata(dev, info);
+
+	for (i = 0; i < dev->num_resources; i++) {
+		printk(KERN_NOTICE "physmap platform flash device: %.8llx at %.8llx\n",
+		       (unsigned long long)resource_size(&dev->resource[i]),
+		       (unsigned long long)dev->resource[i].start);
+
+		if (!devm_request_mem_region(&dev->dev,
+			dev->resource[i].start,
+			resource_size(&dev->resource[i]),
+			dev_name(&dev->dev))) {
+			dev_err(&dev->dev, "Could not reserve memory region\n");
+			err = -ENOMEM;
+			goto err_out;
+		}
+
+		info->map[i].name = dev_name(&dev->dev);
+		info->map[i].phys = dev->resource[i].start;
+		info->map[i].size = resource_size(&dev->resource[i]);
+		info->map[i].bankwidth = physmap_data->width;
+		info->map[i].set_vpp = physmap_set_vpp;
+		info->map[i].pfow_base = physmap_data->pfow_base;
+		info->map[i].map_priv_1 = (unsigned long)dev;
+
+		info->map[i].virt = devm_ioremap(&dev->dev, info->map[i].phys,
+						 info->map[i].size);
+		if (info->map[i].virt == NULL) {
+			dev_err(&dev->dev, "Failed to ioremap flash region\n");
+			err = -EIO;
+			goto err_out;
+		}
+
+		simple_map_init(&info->map[i]);
+
+		probe_type = rom_probe_types;
+		if (physmap_data->probe_type == NULL) {
+			for (; info->mtd[i] == NULL && *probe_type != NULL; probe_type++)
+				info->mtd[i] = do_map_probe(*probe_type, &info->map[i]);
+		} else
+			info->mtd[i] = do_map_probe(physmap_data->probe_type, &info->map[i]);
+
+		if (info->mtd[i] == NULL) {
+			dev_err(&dev->dev, "map_probe failed\n");
+			err = -ENXIO;
+			goto err_out;
+		} else {
+			devices_found++;
+		}
+		info->mtd[i]->owner = THIS_MODULE;
+		info->mtd[i]->dev.parent = &dev->dev;
+	}
+
+	if (devices_found == 1) {
+		info->cmtd = info->mtd[0];
+	} else if (devices_found > 1) {
+		/*
+		 * We detected multiple devices. Concatenate them together.
+		 */
+		info->cmtd = mtd_concat_create(info->mtd, devices_found, dev_name(&dev->dev));
+		if (info->cmtd == NULL)
+			err = -ENXIO;
+	}
+	if (err)
+		goto err_out;
+
+	spin_lock_init(&info->vpp_lock);
+
+	part_types = physmap_data->part_probe_types ? : part_probe_types;
+
+	mtd_device_parse_register(info->cmtd, part_types, NULL,
+				  physmap_data->parts, physmap_data->nr_parts);
+	return 0;
+
+err_out:
+	physmap_flash_remove(dev);
+	return err;
+}
+
+#ifdef CONFIG_PM
+static void physmap_flash_shutdown(struct platform_device *dev)
+{
+	struct physmap_flash_info *info = platform_get_drvdata(dev);
+	int i;
+
+	for (i = 0; i < MAX_RESOURCES && info->mtd[i]; i++)
+		if (mtd_suspend(info->mtd[i]) == 0)
+			mtd_resume(info->mtd[i]);
+}
+#else
+#define physmap_flash_shutdown NULL
+#endif
+
+static struct platform_driver physmap_flash_driver = {
+	.probe		= physmap_flash_probe,
+	.remove		= physmap_flash_remove,
+	.shutdown	= physmap_flash_shutdown,
+	.driver		= {
+		.name	= "physmap-flash",
+	},
+};
+
+
+#ifdef CONFIG_MTD_PHYSMAP_COMPAT
+static struct physmap_flash_data physmap_flash_data = {
+	.width		= CONFIG_MTD_PHYSMAP_BANKWIDTH,
+};
+
+static struct resource physmap_flash_resource = {
+	.start		= CONFIG_MTD_PHYSMAP_START,
+	.end		= CONFIG_MTD_PHYSMAP_START + CONFIG_MTD_PHYSMAP_LEN - 1,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device physmap_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &physmap_flash_data,
+	},
+	.num_resources	= 1,
+	.resource	= &physmap_flash_resource,
+};
+#endif
+
+static int __init physmap_init(void)
+{
+	int err;
+
+	err = platform_driver_register(&physmap_flash_driver);
+#ifdef CONFIG_MTD_PHYSMAP_COMPAT
+	if (err == 0) {
+		err = platform_device_register(&physmap_flash);
+		if (err)
+			platform_driver_unregister(&physmap_flash_driver);
+	}
+#endif
+
+	return err;
+}
+
+static void __exit physmap_exit(void)
+{
+#ifdef CONFIG_MTD_PHYSMAP_COMPAT
+	platform_device_unregister(&physmap_flash);
+#endif
+	platform_driver_unregister(&physmap_flash_driver);
+}
+
+module_init(physmap_init);
+module_exit(physmap_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>");
+MODULE_DESCRIPTION("Generic configurable MTD map driver");
+
+/* legacy platform drivers can't hotplug or coldplg */
+#ifndef CONFIG_MTD_PHYSMAP_COMPAT
+/* work with hotplug and coldplug */
+MODULE_ALIAS("platform:physmap-flash");
+#endif
diff --git a/drivers/mtd/maps/physmap_of.c b/drivers/mtd/maps/physmap_of.c
new file mode 100644
index 000000000..ff26e979b
--- /dev/null
+++ b/drivers/mtd/maps/physmap_of.c
@@ -0,0 +1,375 @@
+/*
+ * Flash mappings described by the OF (or flattened) device tree
+ *
+ * Copyright (C) 2006 MontaVista Software Inc.
+ * Author: Vitaly Wool <vwool@ru.mvista.com>
+ *
+ * Revised to handle newer style flash binding by:
+ *   Copyright (C) 2007 David Gibson, IBM Corporation.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/concat.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/slab.h>
+
+struct of_flash_list {
+	struct mtd_info *mtd;
+	struct map_info map;
+	struct resource *res;
+};
+
+struct of_flash {
+	struct mtd_info		*cmtd;
+	int list_size; /* number of elements in of_flash_list */
+	struct of_flash_list	list[0];
+};
+
+static int of_flash_remove(struct platform_device *dev)
+{
+	struct of_flash *info;
+	int i;
+
+	info = dev_get_drvdata(&dev->dev);
+	if (!info)
+		return 0;
+	dev_set_drvdata(&dev->dev, NULL);
+
+	if (info->cmtd) {
+		mtd_device_unregister(info->cmtd);
+		if (info->cmtd != info->list[0].mtd)
+			mtd_concat_destroy(info->cmtd);
+	}
+
+	for (i = 0; i < info->list_size; i++) {
+		if (info->list[i].mtd)
+			map_destroy(info->list[i].mtd);
+
+		if (info->list[i].map.virt)
+			iounmap(info->list[i].map.virt);
+
+		if (info->list[i].res) {
+			release_resource(info->list[i].res);
+			kfree(info->list[i].res);
+		}
+	}
+	return 0;
+}
+
+static const char * const rom_probe_types[] = {
+	"cfi_probe", "jedec_probe", "map_rom" };
+
+/* Helper function to handle probing of the obsolete "direct-mapped"
+ * compatible binding, which has an extra "probe-type" property
+ * describing the type of flash probe necessary. */
+static struct mtd_info *obsolete_probe(struct platform_device *dev,
+				       struct map_info *map)
+{
+	struct device_node *dp = dev->dev.of_node;
+	const char *of_probe;
+	struct mtd_info *mtd;
+	int i;
+
+	dev_warn(&dev->dev, "Device tree uses obsolete \"direct-mapped\" "
+		 "flash binding\n");
+
+	of_probe = of_get_property(dp, "probe-type", NULL);
+	if (!of_probe) {
+		for (i = 0; i < ARRAY_SIZE(rom_probe_types); i++) {
+			mtd = do_map_probe(rom_probe_types[i], map);
+			if (mtd)
+				return mtd;
+		}
+		return NULL;
+	} else if (strcmp(of_probe, "CFI") == 0) {
+		return do_map_probe("cfi_probe", map);
+	} else if (strcmp(of_probe, "JEDEC") == 0) {
+		return do_map_probe("jedec_probe", map);
+	} else {
+		if (strcmp(of_probe, "ROM") != 0)
+			dev_warn(&dev->dev, "obsolete_probe: don't know probe "
+				 "type '%s', mapping as rom\n", of_probe);
+		return do_map_probe("map_rom", map);
+	}
+}
+
+/* When partitions are set we look for a linux,part-probe property which
+   specifies the list of partition probers to use. If none is given then the
+   default is use. These take precedence over other device tree
+   information. */
+static const char * const part_probe_types_def[] = {
+	"cmdlinepart", "RedBoot", "ofpart", "ofoldpart", NULL };
+
+static const char * const *of_get_probes(struct device_node *dp)
+{
+	const char *cp;
+	int cplen;
+	unsigned int l;
+	unsigned int count;
+	const char **res;
+
+	cp = of_get_property(dp, "linux,part-probe", &cplen);
+	if (cp == NULL)
+		return part_probe_types_def;
+
+	count = 0;
+	for (l = 0; l != cplen; l++)
+		if (cp[l] == 0)
+			count++;
+
+	res = kzalloc((count + 1)*sizeof(*res), GFP_KERNEL);
+	count = 0;
+	while (cplen > 0) {
+		res[count] = cp;
+		l = strlen(cp) + 1;
+		cp += l;
+		cplen -= l;
+		count++;
+	}
+	return res;
+}
+
+static void of_free_probes(const char * const *probes)
+{
+	if (probes != part_probe_types_def)
+		kfree(probes);
+}
+
+static struct of_device_id of_flash_match[];
+static int of_flash_probe(struct platform_device *dev)
+{
+	const char * const *part_probe_types;
+	const struct of_device_id *match;
+	struct device_node *dp = dev->dev.of_node;
+	struct resource res;
+	struct of_flash *info;
+	const char *probe_type;
+	const __be32 *width;
+	int err;
+	int i;
+	int count;
+	const __be32 *p;
+	int reg_tuple_size;
+	struct mtd_info **mtd_list = NULL;
+	resource_size_t res_size;
+	struct mtd_part_parser_data ppdata;
+	bool map_indirect;
+	const char *mtd_name = NULL;
+
+	match = of_match_device(of_flash_match, &dev->dev);
+	if (!match)
+		return -EINVAL;
+	probe_type = match->data;
+
+	reg_tuple_size = (of_n_addr_cells(dp) + of_n_size_cells(dp)) * sizeof(u32);
+
+	of_property_read_string(dp, "linux,mtd-name", &mtd_name);
+
+	/*
+	 * Get number of "reg" tuples. Scan for MTD devices on area's
+	 * described by each "reg" region. This makes it possible (including
+	 * the concat support) to support the Intel P30 48F4400 chips which
+	 * consists internally of 2 non-identical NOR chips on one die.
+	 */
+	p = of_get_property(dp, "reg", &count);
+	if (count % reg_tuple_size != 0) {
+		dev_err(&dev->dev, "Malformed reg property on %s\n",
+				dev->dev.of_node->full_name);
+		err = -EINVAL;
+		goto err_flash_remove;
+	}
+	count /= reg_tuple_size;
+
+	map_indirect = of_property_read_bool(dp, "no-unaligned-direct-access");
+
+	err = -ENOMEM;
+	info = devm_kzalloc(&dev->dev,
+			    sizeof(struct of_flash) +
+			    sizeof(struct of_flash_list) * count, GFP_KERNEL);
+	if (!info)
+		goto err_flash_remove;
+
+	dev_set_drvdata(&dev->dev, info);
+
+	mtd_list = kzalloc(sizeof(*mtd_list) * count, GFP_KERNEL);
+	if (!mtd_list)
+		goto err_flash_remove;
+
+	for (i = 0; i < count; i++) {
+		err = -ENXIO;
+		if (of_address_to_resource(dp, i, &res)) {
+			/*
+			 * Continue with next register tuple if this
+			 * one is not mappable
+			 */
+			continue;
+		}
+
+		dev_dbg(&dev->dev, "of_flash device: %pR\n", &res);
+
+		err = -EBUSY;
+		res_size = resource_size(&res);
+		info->list[i].res = request_mem_region(res.start, res_size,
+						       dev_name(&dev->dev));
+		if (!info->list[i].res)
+			goto err_out;
+
+		err = -ENXIO;
+		width = of_get_property(dp, "bank-width", NULL);
+		if (!width) {
+			dev_err(&dev->dev, "Can't get bank width from device"
+				" tree\n");
+			goto err_out;
+		}
+
+		info->list[i].map.name = mtd_name ?: dev_name(&dev->dev);
+		info->list[i].map.phys = res.start;
+		info->list[i].map.size = res_size;
+		info->list[i].map.bankwidth = be32_to_cpup(width);
+		info->list[i].map.device_node = dp;
+
+		err = -ENOMEM;
+		info->list[i].map.virt = ioremap(info->list[i].map.phys,
+						 info->list[i].map.size);
+		if (!info->list[i].map.virt) {
+			dev_err(&dev->dev, "Failed to ioremap() flash"
+				" region\n");
+			goto err_out;
+		}
+
+		simple_map_init(&info->list[i].map);
+
+		/*
+		 * On some platforms (e.g. MPC5200) a direct 1:1 mapping
+		 * may cause problems with JFFS2 usage, as the local bus (LPB)
+		 * doesn't support unaligned accesses as implemented in the
+		 * JFFS2 code via memcpy(). By setting NO_XIP, the
+		 * flash will not be exposed directly to the MTD users
+		 * (e.g. JFFS2) any more.
+		 */
+		if (map_indirect)
+			info->list[i].map.phys = NO_XIP;
+
+		if (probe_type) {
+			info->list[i].mtd = do_map_probe(probe_type,
+							 &info->list[i].map);
+		} else {
+			info->list[i].mtd = obsolete_probe(dev,
+							   &info->list[i].map);
+		}
+
+		/* Fall back to mapping region as ROM */
+		if (!info->list[i].mtd) {
+			dev_warn(&dev->dev,
+				"do_map_probe() failed for type %s\n",
+				 probe_type);
+
+			info->list[i].mtd = do_map_probe("map_rom",
+							 &info->list[i].map);
+		}
+		mtd_list[i] = info->list[i].mtd;
+
+		err = -ENXIO;
+		if (!info->list[i].mtd) {
+			dev_err(&dev->dev, "do_map_probe() failed\n");
+			goto err_out;
+		} else {
+			info->list_size++;
+		}
+		info->list[i].mtd->owner = THIS_MODULE;
+		info->list[i].mtd->dev.parent = &dev->dev;
+	}
+
+	err = 0;
+	info->cmtd = NULL;
+	if (info->list_size == 1) {
+		info->cmtd = info->list[0].mtd;
+	} else if (info->list_size > 1) {
+		/*
+		 * We detected multiple devices. Concatenate them together.
+		 */
+		info->cmtd = mtd_concat_create(mtd_list, info->list_size,
+					       dev_name(&dev->dev));
+	}
+	if (info->cmtd == NULL)
+		err = -ENXIO;
+
+	if (err)
+		goto err_out;
+
+	ppdata.of_node = dp;
+	part_probe_types = of_get_probes(dp);
+	mtd_device_parse_register(info->cmtd, part_probe_types, &ppdata,
+			NULL, 0);
+	of_free_probes(part_probe_types);
+
+	kfree(mtd_list);
+
+	return 0;
+
+err_out:
+	kfree(mtd_list);
+err_flash_remove:
+	of_flash_remove(dev);
+
+	return err;
+}
+
+static struct of_device_id of_flash_match[] = {
+	{
+		.compatible	= "cfi-flash",
+		.data		= (void *)"cfi_probe",
+	},
+	{
+		/* FIXME: JEDEC chips can't be safely and reliably
+		 * probed, although the mtd code gets it right in
+		 * practice most of the time.  We should use the
+		 * vendor and device ids specified by the binding to
+		 * bypass the heuristic probe code, but the mtd layer
+		 * provides, at present, no interface for doing so
+		 * :(. */
+		.compatible	= "jedec-flash",
+		.data		= (void *)"jedec_probe",
+	},
+	{
+		.compatible     = "mtd-ram",
+		.data           = (void *)"map_ram",
+	},
+	{
+		.compatible     = "mtd-rom",
+		.data           = (void *)"map_rom",
+	},
+	{
+		.type		= "rom",
+		.compatible	= "direct-mapped"
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, of_flash_match);
+
+static struct platform_driver of_flash_driver = {
+	.driver = {
+		.name = "of-flash",
+		.of_match_table = of_flash_match,
+	},
+	.probe		= of_flash_probe,
+	.remove		= of_flash_remove,
+};
+
+module_platform_driver(of_flash_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Vitaly Wool <vwool@ru.mvista.com>");
+MODULE_DESCRIPTION("Device tree based MTD map driver");
diff --git a/drivers/mtd/maps/pismo.c b/drivers/mtd/maps/pismo.c
new file mode 100644
index 000000000..dc6df9abe
--- /dev/null
+++ b/drivers/mtd/maps/pismo.c
@@ -0,0 +1,292 @@
+/*
+ * PISMO memory driver - http://www.pismoworld.org/
+ *
+ * For ARM Realview and Versatile platforms
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include <linux/mutex.h>
+#include <linux/mtd/physmap.h>
+#include <linux/mtd/plat-ram.h>
+#include <linux/mtd/pismo.h>
+
+#define PISMO_NUM_CS	5
+
+struct pismo_cs_block {
+	u8	type;
+	u8	width;
+	__le16	access;
+	__le32	size;
+	u32	reserved[2];
+	char	device[32];
+} __packed;
+
+struct pismo_eeprom {
+	struct pismo_cs_block cs[PISMO_NUM_CS];
+	char	board[15];
+	u8	sum;
+} __packed;
+
+struct pismo_mem {
+	phys_addr_t base;
+	u32	size;
+	u16	access;
+	u8	width;
+	u8	type;
+};
+
+struct pismo_data {
+	struct i2c_client	*client;
+	void			(*vpp)(void *, int);
+	void			*vpp_data;
+	struct platform_device	*dev[PISMO_NUM_CS];
+};
+
+static void pismo_set_vpp(struct platform_device *pdev, int on)
+{
+	struct i2c_client *client = to_i2c_client(pdev->dev.parent);
+	struct pismo_data *pismo = i2c_get_clientdata(client);
+
+	pismo->vpp(pismo->vpp_data, on);
+}
+
+static unsigned int pismo_width_to_bytes(unsigned int width)
+{
+	width &= 15;
+	if (width > 2)
+		return 0;
+	return 1 << width;
+}
+
+static int pismo_eeprom_read(struct i2c_client *client, void *buf, u8 addr,
+			     size_t size)
+{
+	int ret;
+	struct i2c_msg msg[] = {
+		{
+			.addr = client->addr,
+			.len = sizeof(addr),
+			.buf = &addr,
+		}, {
+			.addr = client->addr,
+			.flags = I2C_M_RD,
+			.len = size,
+			.buf = buf,
+		},
+	};
+
+	ret = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg));
+
+	return ret == ARRAY_SIZE(msg) ? size : -EIO;
+}
+
+static int pismo_add_device(struct pismo_data *pismo, int i,
+			    struct pismo_mem *region, const char *name,
+			    void *pdata, size_t psize)
+{
+	struct platform_device *dev;
+	struct resource res = { };
+	phys_addr_t base = region->base;
+	int ret;
+
+	if (base == ~0)
+		return -ENXIO;
+
+	res.start = base;
+	res.end = base + region->size - 1;
+	res.flags = IORESOURCE_MEM;
+
+	dev = platform_device_alloc(name, i);
+	if (!dev)
+		return -ENOMEM;
+	dev->dev.parent = &pismo->client->dev;
+
+	do {
+		ret = platform_device_add_resources(dev, &res, 1);
+		if (ret)
+			break;
+
+		ret = platform_device_add_data(dev, pdata, psize);
+		if (ret)
+			break;
+
+		ret = platform_device_add(dev);
+		if (ret)
+			break;
+
+		pismo->dev[i] = dev;
+		return 0;
+	} while (0);
+
+	platform_device_put(dev);
+	return ret;
+}
+
+static int pismo_add_nor(struct pismo_data *pismo, int i,
+			 struct pismo_mem *region)
+{
+	struct physmap_flash_data data = {
+		.width = region->width,
+	};
+
+	if (pismo->vpp)
+		data.set_vpp = pismo_set_vpp;
+
+	return pismo_add_device(pismo, i, region, "physmap-flash",
+		&data, sizeof(data));
+}
+
+static int pismo_add_sram(struct pismo_data *pismo, int i,
+			  struct pismo_mem *region)
+{
+	struct platdata_mtd_ram data = {
+		.bankwidth = region->width,
+	};
+
+	return pismo_add_device(pismo, i, region, "mtd-ram",
+		&data, sizeof(data));
+}
+
+static void pismo_add_one(struct pismo_data *pismo, int i,
+			  const struct pismo_cs_block *cs, phys_addr_t base)
+{
+	struct device *dev = &pismo->client->dev;
+	struct pismo_mem region;
+
+	region.base = base;
+	region.type = cs->type;
+	region.width = pismo_width_to_bytes(cs->width);
+	region.access = le16_to_cpu(cs->access);
+	region.size = le32_to_cpu(cs->size);
+
+	if (region.width == 0) {
+		dev_err(dev, "cs%u: bad width: %02x, ignoring\n", i, cs->width);
+		return;
+	}
+
+	/*
+	 * FIXME: may need to the platforms memory controller here, but at
+	 * the moment we assume that it has already been correctly setup.
+	 * The memory controller can also tell us the base address as well.
+	 */
+
+	dev_info(dev, "cs%u: %.32s: type %02x access %u00ps size %uK\n",
+		i, cs->device, region.type, region.access, region.size / 1024);
+
+	switch (region.type) {
+	case 0:
+		break;
+	case 1:
+		/* static DOC */
+		break;
+	case 2:
+		/* static NOR */
+		pismo_add_nor(pismo, i, &region);
+		break;
+	case 3:
+		/* static RAM */
+		pismo_add_sram(pismo, i, &region);
+		break;
+	}
+}
+
+static int pismo_remove(struct i2c_client *client)
+{
+	struct pismo_data *pismo = i2c_get_clientdata(client);
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(pismo->dev); i++)
+		platform_device_unregister(pismo->dev[i]);
+
+	kfree(pismo);
+
+	return 0;
+}
+
+static int pismo_probe(struct i2c_client *client,
+		       const struct i2c_device_id *id)
+{
+	struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
+	struct pismo_pdata *pdata = client->dev.platform_data;
+	struct pismo_eeprom eeprom;
+	struct pismo_data *pismo;
+	int ret, i;
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_I2C)) {
+		dev_err(&client->dev, "functionality mismatch\n");
+		return -EIO;
+	}
+
+	pismo = kzalloc(sizeof(*pismo), GFP_KERNEL);
+	if (!pismo)
+		return -ENOMEM;
+
+	pismo->client = client;
+	if (pdata) {
+		pismo->vpp = pdata->set_vpp;
+		pismo->vpp_data = pdata->vpp_data;
+	}
+	i2c_set_clientdata(client, pismo);
+
+	ret = pismo_eeprom_read(client, &eeprom, 0, sizeof(eeprom));
+	if (ret < 0) {
+		dev_err(&client->dev, "error reading EEPROM: %d\n", ret);
+		goto exit_free;
+	}
+
+	dev_info(&client->dev, "%.15s board found\n", eeprom.board);
+
+	for (i = 0; i < ARRAY_SIZE(eeprom.cs); i++)
+		if (eeprom.cs[i].type != 0xff)
+			pismo_add_one(pismo, i, &eeprom.cs[i],
+				      pdata->cs_addrs[i]);
+
+	return 0;
+
+ exit_free:
+	kfree(pismo);
+	return ret;
+}
+
+static const struct i2c_device_id pismo_id[] = {
+	{ "pismo" },
+	{ },
+};
+MODULE_DEVICE_TABLE(i2c, pismo_id);
+
+static struct i2c_driver pismo_driver = {
+	.driver	= {
+		.name	= "pismo",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= pismo_probe,
+	.remove		= pismo_remove,
+	.id_table	= pismo_id,
+};
+
+static int __init pismo_init(void)
+{
+	BUILD_BUG_ON(sizeof(struct pismo_cs_block) != 48);
+	BUILD_BUG_ON(sizeof(struct pismo_eeprom) != 256);
+
+	return i2c_add_driver(&pismo_driver);
+}
+module_init(pismo_init);
+
+static void __exit pismo_exit(void)
+{
+	i2c_del_driver(&pismo_driver);
+}
+module_exit(pismo_exit);
+
+MODULE_AUTHOR("Russell King <linux@arm.linux.org.uk>");
+MODULE_DESCRIPTION("PISMO memory driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mtd/maps/plat-ram.c b/drivers/mtd/maps/plat-ram.c
new file mode 100644
index 000000000..4b65c08d1
--- /dev/null
+++ b/drivers/mtd/maps/plat-ram.c
@@ -0,0 +1,261 @@
+/* drivers/mtd/maps/plat-ram.c
+ *
+ * (c) 2004-2005 Simtec Electronics
+ *	http://www.simtec.co.uk/products/SWLINUX/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Generic platform device based RAM map
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+*/
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/plat-ram.h>
+
+#include <asm/io.h>
+
+/* private structure for each mtd platform ram device created */
+
+struct platram_info {
+	struct device		*dev;
+	struct mtd_info		*mtd;
+	struct map_info		 map;
+	struct resource		*area;
+	struct platdata_mtd_ram	*pdata;
+};
+
+/* to_platram_info()
+ *
+ * device private data to struct platram_info conversion
+*/
+
+static inline struct platram_info *to_platram_info(struct platform_device *dev)
+{
+	return platform_get_drvdata(dev);
+}
+
+/* platram_setrw
+ *
+ * call the platform device's set rw/ro control
+ *
+ * to = 0 => read-only
+ *    = 1 => read-write
+*/
+
+static inline void platram_setrw(struct platram_info *info, int to)
+{
+	if (info->pdata == NULL)
+		return;
+
+	if (info->pdata->set_rw != NULL)
+		(info->pdata->set_rw)(info->dev, to);
+}
+
+/* platram_remove
+ *
+ * called to remove the device from the driver's control
+*/
+
+static int platram_remove(struct platform_device *pdev)
+{
+	struct platram_info *info = to_platram_info(pdev);
+
+	dev_dbg(&pdev->dev, "removing device\n");
+
+	if (info == NULL)
+		return 0;
+
+	if (info->mtd) {
+		mtd_device_unregister(info->mtd);
+		map_destroy(info->mtd);
+	}
+
+	/* ensure ram is left read-only */
+
+	platram_setrw(info, PLATRAM_RO);
+
+	/* release resources */
+
+	if (info->area) {
+		release_resource(info->area);
+		kfree(info->area);
+	}
+
+	if (info->map.virt != NULL)
+		iounmap(info->map.virt);
+
+	kfree(info);
+
+	return 0;
+}
+
+/* platram_probe
+ *
+ * called from device drive system when a device matching our
+ * driver is found.
+*/
+
+static int platram_probe(struct platform_device *pdev)
+{
+	struct platdata_mtd_ram	*pdata;
+	struct platram_info *info;
+	struct resource *res;
+	int err = 0;
+
+	dev_dbg(&pdev->dev, "probe entered\n");
+
+	if (dev_get_platdata(&pdev->dev) == NULL) {
+		dev_err(&pdev->dev, "no platform data supplied\n");
+		err = -ENOENT;
+		goto exit_error;
+	}
+
+	pdata = dev_get_platdata(&pdev->dev);
+
+	info = kzalloc(sizeof(*info), GFP_KERNEL);
+	if (info == NULL) {
+		err = -ENOMEM;
+		goto exit_error;
+	}
+
+	platform_set_drvdata(pdev, info);
+
+	info->dev = &pdev->dev;
+	info->pdata = pdata;
+
+	/* get the resource for the memory mapping */
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+	if (res == NULL) {
+		dev_err(&pdev->dev, "no memory resource specified\n");
+		err = -ENOENT;
+		goto exit_free;
+	}
+
+	dev_dbg(&pdev->dev, "got platform resource %p (0x%llx)\n", res,
+		(unsigned long long)res->start);
+
+	/* setup map parameters */
+
+	info->map.phys = res->start;
+	info->map.size = resource_size(res);
+	info->map.name = pdata->mapname != NULL ?
+			(char *)pdata->mapname : (char *)pdev->name;
+	info->map.bankwidth = pdata->bankwidth;
+
+	/* register our usage of the memory area */
+
+	info->area = request_mem_region(res->start, info->map.size, pdev->name);
+	if (info->area == NULL) {
+		dev_err(&pdev->dev, "failed to request memory region\n");
+		err = -EIO;
+		goto exit_free;
+	}
+
+	/* remap the memory area */
+
+	info->map.virt = ioremap(res->start, info->map.size);
+	dev_dbg(&pdev->dev, "virt %p, %lu bytes\n", info->map.virt, info->map.size);
+
+	if (info->map.virt == NULL) {
+		dev_err(&pdev->dev, "failed to ioremap() region\n");
+		err = -EIO;
+		goto exit_free;
+	}
+
+	simple_map_init(&info->map);
+
+	dev_dbg(&pdev->dev, "initialised map, probing for mtd\n");
+
+	/* probe for the right mtd map driver
+	 * supplied by the platform_data struct */
+
+	if (pdata->map_probes) {
+		const char * const *map_probes = pdata->map_probes;
+
+		for ( ; !info->mtd && *map_probes; map_probes++)
+			info->mtd = do_map_probe(*map_probes , &info->map);
+	}
+	/* fallback to map_ram */
+	else
+		info->mtd = do_map_probe("map_ram", &info->map);
+
+	if (info->mtd == NULL) {
+		dev_err(&pdev->dev, "failed to probe for map_ram\n");
+		err = -ENOMEM;
+		goto exit_free;
+	}
+
+	info->mtd->owner = THIS_MODULE;
+	info->mtd->dev.parent = &pdev->dev;
+
+	platram_setrw(info, PLATRAM_RW);
+
+	/* check to see if there are any available partitions, or whether
+	 * to add this device whole */
+
+	err = mtd_device_parse_register(info->mtd, pdata->probes, NULL,
+					pdata->partitions,
+					pdata->nr_partitions);
+	if (!err)
+		dev_info(&pdev->dev, "registered mtd device\n");
+
+	if (pdata->nr_partitions) {
+		/* add the whole device. */
+		err = mtd_device_register(info->mtd, NULL, 0);
+		if (err) {
+			dev_err(&pdev->dev,
+				"failed to register the entire device\n");
+		}
+	}
+
+	return err;
+
+ exit_free:
+	platram_remove(pdev);
+ exit_error:
+	return err;
+}
+
+/* device driver info */
+
+/* work with hotplug and coldplug */
+MODULE_ALIAS("platform:mtd-ram");
+
+static struct platform_driver platram_driver = {
+	.probe		= platram_probe,
+	.remove		= platram_remove,
+	.driver		= {
+		.name	= "mtd-ram",
+	},
+};
+
+module_platform_driver(platram_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
+MODULE_DESCRIPTION("MTD platform RAM map driver");
diff --git a/drivers/mtd/maps/pmcmsp-flash.c b/drivers/mtd/maps/pmcmsp-flash.c
new file mode 100644
index 000000000..744ca5cac
--- /dev/null
+++ b/drivers/mtd/maps/pmcmsp-flash.c
@@ -0,0 +1,229 @@
+/*
+ * Mapping of a custom board with both AMD CFI and JEDEC flash in partitions.
+ * Config with both CFI and JEDEC device support.
+ *
+ * Basically physmap.c with the addition of partitions and
+ * an array of mapping info to accommodate more than one flash type per board.
+ *
+ * Copyright 2005-2007 PMC-Sierra, Inc.
+ *
+ *  This program is free software; you can redistribute  it and/or modify it
+ *  under  the terms of  the GNU General  Public License as published by the
+ *  Free Software Foundation;  either version 2 of the  License, or (at your
+ *  option) any later version.
+ *
+ *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
+ *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
+ *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
+ *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
+ *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
+ *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *  You should have received a copy of the  GNU General Public License along
+ *  with this program; if not, write  to the Free Software Foundation, Inc.,
+ *  675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/io.h>
+
+#include <msp_prom.h>
+#include <msp_regs.h>
+
+
+static struct mtd_info **msp_flash;
+static struct mtd_partition **msp_parts;
+static struct map_info *msp_maps;
+static int fcnt;
+
+#define DEBUG_MARKER printk(KERN_NOTICE "%s[%d]\n", __func__, __LINE__)
+
+static int __init init_msp_flash(void)
+{
+	int i, j, ret = -ENOMEM;
+	int offset, coff;
+	char *env;
+	int pcnt;
+	char flash_name[] = "flash0";
+	char part_name[] = "flash0_0";
+	unsigned addr, size;
+
+	/* If ELB is disabled by "ful-mux" mode, we can't get at flash */
+	if ((*DEV_ID_REG & DEV_ID_SINGLE_PC) &&
+	    (*ELB_1PC_EN_REG & SINGLE_PCCARD)) {
+		printk(KERN_NOTICE "Single PC Card mode: no flash access\n");
+		return -ENXIO;
+	}
+
+	/* examine the prom environment for flash devices */
+	for (fcnt = 0; (env = prom_getenv(flash_name)); fcnt++)
+		flash_name[5] = '0' + fcnt + 1;
+
+	if (fcnt < 1)
+		return -ENXIO;
+
+	printk(KERN_NOTICE "Found %d PMC flash devices\n", fcnt);
+
+	msp_flash = kmalloc(fcnt * sizeof(struct map_info *), GFP_KERNEL);
+	if (!msp_flash)
+		return -ENOMEM;
+
+	msp_parts = kmalloc(fcnt * sizeof(struct mtd_partition *), GFP_KERNEL);
+	if (!msp_parts)
+		goto free_msp_flash;
+
+	msp_maps = kcalloc(fcnt, sizeof(struct mtd_info), GFP_KERNEL);
+	if (!msp_maps)
+		goto free_msp_parts;
+
+	/* loop over the flash devices, initializing each */
+	for (i = 0; i < fcnt; i++) {
+		/* examine the prom environment for flash partititions */
+		part_name[5] = '0' + i;
+		part_name[7] = '0';
+		for (pcnt = 0; (env = prom_getenv(part_name)); pcnt++)
+			part_name[7] = '0' + pcnt + 1;
+
+		if (pcnt == 0) {
+			printk(KERN_NOTICE "Skipping flash device %d "
+				"(no partitions defined)\n", i);
+			continue;
+		}
+
+		msp_parts[i] = kcalloc(pcnt, sizeof(struct mtd_partition),
+				       GFP_KERNEL);
+		if (!msp_parts[i])
+			goto cleanup_loop;
+
+		/* now initialize the devices proper */
+		flash_name[5] = '0' + i;
+		env = prom_getenv(flash_name);
+
+		if (sscanf(env, "%x:%x", &addr, &size) < 2) {
+			ret = -ENXIO;
+			kfree(msp_parts[i]);
+			goto cleanup_loop;
+		}
+		addr = CPHYSADDR(addr);
+
+		printk(KERN_NOTICE
+			"MSP flash device \"%s\": 0x%08x at 0x%08x\n",
+			flash_name, size, addr);
+		/* This must matchs the actual size of the flash chip */
+		msp_maps[i].size = size;
+		msp_maps[i].phys = addr;
+
+		/*
+		 * Platforms have a specific limit of the size of memory
+		 * which may be mapped for flash:
+		 */
+		if (size > CONFIG_MSP_FLASH_MAP_LIMIT)
+			size = CONFIG_MSP_FLASH_MAP_LIMIT;
+
+		msp_maps[i].virt = ioremap(addr, size);
+		if (msp_maps[i].virt == NULL) {
+			ret = -ENXIO;
+			kfree(msp_parts[i]);
+			goto cleanup_loop;
+		}
+
+		msp_maps[i].bankwidth = 1;
+		msp_maps[i].name = kmalloc(7, GFP_KERNEL);
+		if (!msp_maps[i].name) {
+			iounmap(msp_maps[i].virt);
+			kfree(msp_parts[i]);
+			goto cleanup_loop;
+		}
+
+		msp_maps[i].name = strncpy(msp_maps[i].name, flash_name, 7);
+
+		for (j = 0; j < pcnt; j++) {
+			part_name[5] = '0' + i;
+			part_name[7] = '0' + j;
+
+			env = prom_getenv(part_name);
+
+			if (sscanf(env, "%x:%x:%n", &offset, &size,
+						&coff) < 2) {
+				ret = -ENXIO;
+				kfree(msp_maps[i].name);
+				iounmap(msp_maps[i].virt);
+				kfree(msp_parts[i]);
+				goto cleanup_loop;
+			}
+
+			msp_parts[i][j].size = size;
+			msp_parts[i][j].offset = offset;
+			msp_parts[i][j].name = env + coff;
+		}
+
+		/* now probe and add the device */
+		simple_map_init(&msp_maps[i]);
+		msp_flash[i] = do_map_probe("cfi_probe", &msp_maps[i]);
+		if (msp_flash[i]) {
+			msp_flash[i]->owner = THIS_MODULE;
+			mtd_device_register(msp_flash[i], msp_parts[i], pcnt);
+		} else {
+			printk(KERN_ERR "map probe failed for flash\n");
+			ret = -ENXIO;
+			kfree(msp_maps[i].name);
+			iounmap(msp_maps[i].virt);
+			kfree(msp_parts[i]);
+			goto cleanup_loop;
+		}
+	}
+
+	return 0;
+
+cleanup_loop:
+	while (i--) {
+		mtd_device_unregister(msp_flash[i]);
+		map_destroy(msp_flash[i]);
+		kfree(msp_maps[i].name);
+		iounmap(msp_maps[i].virt);
+		kfree(msp_parts[i]);
+	}
+	kfree(msp_maps);
+free_msp_parts:
+	kfree(msp_parts);
+free_msp_flash:
+	kfree(msp_flash);
+	return ret;
+}
+
+static void __exit cleanup_msp_flash(void)
+{
+	int i;
+
+	for (i = 0; i < fcnt; i++) {
+		mtd_device_unregister(msp_flash[i]);
+		map_destroy(msp_flash[i]);
+		iounmap((void *)msp_maps[i].virt);
+
+		/* free the memory */
+		kfree(msp_maps[i].name);
+		kfree(msp_parts[i]);
+	}
+
+	kfree(msp_flash);
+	kfree(msp_parts);
+	kfree(msp_maps);
+}
+
+MODULE_AUTHOR("PMC-Sierra, Inc");
+MODULE_DESCRIPTION("MTD map driver for PMC-Sierra MSP boards");
+MODULE_LICENSE("GPL");
+
+module_init(init_msp_flash);
+module_exit(cleanup_msp_flash);
diff --git a/drivers/mtd/maps/pxa2xx-flash.c b/drivers/mtd/maps/pxa2xx-flash.c
new file mode 100644
index 000000000..12fa75df5
--- /dev/null
+++ b/drivers/mtd/maps/pxa2xx-flash.c
@@ -0,0 +1,144 @@
+/*
+ * Map driver for Intel XScale PXA2xx platforms.
+ *
+ * Author:	Nicolas Pitre
+ * Copyright:	(C) 2001 MontaVista Software Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/io.h>
+#include <mach/hardware.h>
+
+#include <asm/mach/flash.h>
+
+#define CACHELINESIZE	32
+
+static void pxa2xx_map_inval_cache(struct map_info *map, unsigned long from,
+				      ssize_t len)
+{
+	unsigned long start = (unsigned long)map->cached + from;
+	unsigned long end = start + len;
+
+	start &= ~(CACHELINESIZE - 1);
+	while (start < end) {
+		/* invalidate D cache line */
+		asm volatile ("mcr p15, 0, %0, c7, c6, 1" : : "r" (start));
+		start += CACHELINESIZE;
+	}
+}
+
+struct pxa2xx_flash_info {
+	struct mtd_info		*mtd;
+	struct map_info		map;
+};
+
+static const char * const probes[] = { "RedBoot", "cmdlinepart", NULL };
+
+static int pxa2xx_flash_probe(struct platform_device *pdev)
+{
+	struct flash_platform_data *flash = dev_get_platdata(&pdev->dev);
+	struct pxa2xx_flash_info *info;
+	struct resource *res;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENODEV;
+
+	info = kzalloc(sizeof(struct pxa2xx_flash_info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	info->map.name = flash->name;
+	info->map.bankwidth = flash->width;
+	info->map.phys = res->start;
+	info->map.size = resource_size(res);
+
+	info->map.virt = ioremap(info->map.phys, info->map.size);
+	if (!info->map.virt) {
+		printk(KERN_WARNING "Failed to ioremap %s\n",
+		       info->map.name);
+		return -ENOMEM;
+	}
+	info->map.cached =
+		ioremap_cache(info->map.phys, info->map.size);
+	if (!info->map.cached)
+		printk(KERN_WARNING "Failed to ioremap cached %s\n",
+		       info->map.name);
+	info->map.inval_cache = pxa2xx_map_inval_cache;
+	simple_map_init(&info->map);
+
+	printk(KERN_NOTICE
+	       "Probing %s at physical address 0x%08lx"
+	       " (%d-bit bankwidth)\n",
+	       info->map.name, (unsigned long)info->map.phys,
+	       info->map.bankwidth * 8);
+
+	info->mtd = do_map_probe(flash->map_name, &info->map);
+
+	if (!info->mtd) {
+		iounmap((void *)info->map.virt);
+		if (info->map.cached)
+			iounmap(info->map.cached);
+		return -EIO;
+	}
+	info->mtd->owner = THIS_MODULE;
+
+	mtd_device_parse_register(info->mtd, probes, NULL, flash->parts,
+				  flash->nr_parts);
+
+	platform_set_drvdata(pdev, info);
+	return 0;
+}
+
+static int pxa2xx_flash_remove(struct platform_device *dev)
+{
+	struct pxa2xx_flash_info *info = platform_get_drvdata(dev);
+
+	mtd_device_unregister(info->mtd);
+
+	map_destroy(info->mtd);
+	iounmap(info->map.virt);
+	if (info->map.cached)
+		iounmap(info->map.cached);
+	kfree(info);
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static void pxa2xx_flash_shutdown(struct platform_device *dev)
+{
+	struct pxa2xx_flash_info *info = platform_get_drvdata(dev);
+
+	if (info && mtd_suspend(info->mtd) == 0)
+		mtd_resume(info->mtd);
+}
+#else
+#define pxa2xx_flash_shutdown NULL
+#endif
+
+static struct platform_driver pxa2xx_flash_driver = {
+	.driver = {
+		.name		= "pxa2xx-flash",
+	},
+	.probe		= pxa2xx_flash_probe,
+	.remove		= pxa2xx_flash_remove,
+	.shutdown	= pxa2xx_flash_shutdown,
+};
+
+module_platform_driver(pxa2xx_flash_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Nicolas Pitre <nico@fluxnic.net>");
+MODULE_DESCRIPTION("MTD map driver for Intel XScale PXA2xx");
diff --git a/drivers/mtd/maps/rbtx4939-flash.c b/drivers/mtd/maps/rbtx4939-flash.c
new file mode 100644
index 000000000..5a7551aa2
--- /dev/null
+++ b/drivers/mtd/maps/rbtx4939-flash.c
@@ -0,0 +1,137 @@
+/*
+ * rbtx4939-flash (based on physmap.c)
+ *
+ * This is a simplified physmap driver with map_init callback function.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Copyright (C) 2009 Atsushi Nemoto <anemo@mba.ocn.ne.jp>
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <asm/txx9/rbtx4939.h>
+
+struct rbtx4939_flash_info {
+	struct mtd_info *mtd;
+	struct map_info map;
+};
+
+static int rbtx4939_flash_remove(struct platform_device *dev)
+{
+	struct rbtx4939_flash_info *info;
+
+	info = platform_get_drvdata(dev);
+	if (!info)
+		return 0;
+
+	if (info->mtd) {
+		mtd_device_unregister(info->mtd);
+		map_destroy(info->mtd);
+	}
+	return 0;
+}
+
+static const char * const rom_probe_types[] = {
+	"cfi_probe", "jedec_probe", NULL };
+
+static int rbtx4939_flash_probe(struct platform_device *dev)
+{
+	struct rbtx4939_flash_data *pdata;
+	struct rbtx4939_flash_info *info;
+	struct resource *res;
+	const char * const *probe_type;
+	int err = 0;
+	unsigned long size;
+
+	pdata = dev_get_platdata(&dev->dev);
+	if (!pdata)
+		return -ENODEV;
+
+	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -ENODEV;
+	info = devm_kzalloc(&dev->dev, sizeof(struct rbtx4939_flash_info),
+			    GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	platform_set_drvdata(dev, info);
+
+	size = resource_size(res);
+	pr_notice("rbtx4939 platform flash device: %pR\n", res);
+
+	if (!devm_request_mem_region(&dev->dev, res->start, size,
+				     dev_name(&dev->dev)))
+		return -EBUSY;
+
+	info->map.name = dev_name(&dev->dev);
+	info->map.phys = res->start;
+	info->map.size = size;
+	info->map.bankwidth = pdata->width;
+
+	info->map.virt = devm_ioremap(&dev->dev, info->map.phys, size);
+	if (!info->map.virt)
+		return -EBUSY;
+
+	if (pdata->map_init)
+		(*pdata->map_init)(&info->map);
+	else
+		simple_map_init(&info->map);
+
+	probe_type = rom_probe_types;
+	for (; !info->mtd && *probe_type; probe_type++)
+		info->mtd = do_map_probe(*probe_type, &info->map);
+	if (!info->mtd) {
+		dev_err(&dev->dev, "map_probe failed\n");
+		err = -ENXIO;
+		goto err_out;
+	}
+	info->mtd->owner = THIS_MODULE;
+	err = mtd_device_parse_register(info->mtd, NULL, NULL, pdata->parts,
+					pdata->nr_parts);
+
+	if (err)
+		goto err_out;
+	return 0;
+
+err_out:
+	rbtx4939_flash_remove(dev);
+	return err;
+}
+
+#ifdef CONFIG_PM
+static void rbtx4939_flash_shutdown(struct platform_device *dev)
+{
+	struct rbtx4939_flash_info *info = platform_get_drvdata(dev);
+
+	if (mtd_suspend(info->mtd) == 0)
+		mtd_resume(info->mtd);
+}
+#else
+#define rbtx4939_flash_shutdown NULL
+#endif
+
+static struct platform_driver rbtx4939_flash_driver = {
+	.probe		= rbtx4939_flash_probe,
+	.remove		= rbtx4939_flash_remove,
+	.shutdown	= rbtx4939_flash_shutdown,
+	.driver		= {
+		.name	= "rbtx4939-flash",
+	},
+};
+
+module_platform_driver(rbtx4939_flash_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("RBTX4939 MTD map driver");
+MODULE_ALIAS("platform:rbtx4939-flash");
diff --git a/drivers/mtd/maps/sa1100-flash.c b/drivers/mtd/maps/sa1100-flash.c
new file mode 100644
index 000000000..892ad6ac6
--- /dev/null
+++ b/drivers/mtd/maps/sa1100-flash.c
@@ -0,0 +1,300 @@
+/*
+ * Flash memory access on SA11x0 based devices
+ *
+ * (C) 2000 Nicolas Pitre <nico@fluxnic.net>
+ */
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/concat.h>
+
+#include <mach/hardware.h>
+#include <asm/sizes.h>
+#include <asm/mach/flash.h>
+
+struct sa_subdev_info {
+	char name[16];
+	struct map_info map;
+	struct mtd_info *mtd;
+	struct flash_platform_data *plat;
+};
+
+struct sa_info {
+	struct mtd_info		*mtd;
+	int			num_subdev;
+	struct sa_subdev_info	subdev[0];
+};
+
+static DEFINE_SPINLOCK(sa1100_vpp_lock);
+static int sa1100_vpp_refcnt;
+static void sa1100_set_vpp(struct map_info *map, int on)
+{
+	struct sa_subdev_info *subdev = container_of(map, struct sa_subdev_info, map);
+	unsigned long flags;
+
+	spin_lock_irqsave(&sa1100_vpp_lock, flags);
+	if (on) {
+		if (++sa1100_vpp_refcnt == 1)   /* first nested 'on' */
+			subdev->plat->set_vpp(1);
+	} else {
+		if (--sa1100_vpp_refcnt == 0)   /* last nested 'off' */
+			subdev->plat->set_vpp(0);
+	}
+	spin_unlock_irqrestore(&sa1100_vpp_lock, flags);
+}
+
+static void sa1100_destroy_subdev(struct sa_subdev_info *subdev)
+{
+	if (subdev->mtd)
+		map_destroy(subdev->mtd);
+	if (subdev->map.virt)
+		iounmap(subdev->map.virt);
+	release_mem_region(subdev->map.phys, subdev->map.size);
+}
+
+static int sa1100_probe_subdev(struct sa_subdev_info *subdev, struct resource *res)
+{
+	unsigned long phys;
+	unsigned int size;
+	int ret;
+
+	phys = res->start;
+	size = res->end - phys + 1;
+
+	/*
+	 * Retrieve the bankwidth from the MSC registers.
+	 * We currently only implement CS0 and CS1 here.
+	 */
+	switch (phys) {
+	default:
+		printk(KERN_WARNING "SA1100 flash: unknown base address "
+		       "0x%08lx, assuming CS0\n", phys);
+
+	case SA1100_CS0_PHYS:
+		subdev->map.bankwidth = (MSC0 & MSC_RBW) ? 2 : 4;
+		break;
+
+	case SA1100_CS1_PHYS:
+		subdev->map.bankwidth = ((MSC0 >> 16) & MSC_RBW) ? 2 : 4;
+		break;
+	}
+
+	if (!request_mem_region(phys, size, subdev->name)) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	if (subdev->plat->set_vpp)
+		subdev->map.set_vpp = sa1100_set_vpp;
+
+	subdev->map.phys = phys;
+	subdev->map.size = size;
+	subdev->map.virt = ioremap(phys, size);
+	if (!subdev->map.virt) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	simple_map_init(&subdev->map);
+
+	/*
+	 * Now let's probe for the actual flash.  Do it here since
+	 * specific machine settings might have been set above.
+	 */
+	subdev->mtd = do_map_probe(subdev->plat->map_name, &subdev->map);
+	if (subdev->mtd == NULL) {
+		ret = -ENXIO;
+		goto err;
+	}
+	subdev->mtd->owner = THIS_MODULE;
+
+	printk(KERN_INFO "SA1100 flash: CFI device at 0x%08lx, %uMiB, %d-bit\n",
+		phys, (unsigned)(subdev->mtd->size >> 20),
+		subdev->map.bankwidth * 8);
+
+	return 0;
+
+ err:
+	sa1100_destroy_subdev(subdev);
+ out:
+	return ret;
+}
+
+static void sa1100_destroy(struct sa_info *info, struct flash_platform_data *plat)
+{
+	int i;
+
+	if (info->mtd) {
+		mtd_device_unregister(info->mtd);
+		if (info->mtd != info->subdev[0].mtd)
+			mtd_concat_destroy(info->mtd);
+	}
+
+	for (i = info->num_subdev - 1; i >= 0; i--)
+		sa1100_destroy_subdev(&info->subdev[i]);
+	kfree(info);
+
+	if (plat->exit)
+		plat->exit();
+}
+
+static struct sa_info *sa1100_setup_mtd(struct platform_device *pdev,
+					struct flash_platform_data *plat)
+{
+	struct sa_info *info;
+	int nr, size, i, ret = 0;
+
+	/*
+	 * Count number of devices.
+	 */
+	for (nr = 0; ; nr++)
+		if (!platform_get_resource(pdev, IORESOURCE_MEM, nr))
+			break;
+
+	if (nr == 0) {
+		ret = -ENODEV;
+		goto out;
+	}
+
+	size = sizeof(struct sa_info) + sizeof(struct sa_subdev_info) * nr;
+
+	/*
+	 * Allocate the map_info structs in one go.
+	 */
+	info = kzalloc(size, GFP_KERNEL);
+	if (!info) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	if (plat->init) {
+		ret = plat->init();
+		if (ret)
+			goto err;
+	}
+
+	/*
+	 * Claim and then map the memory regions.
+	 */
+	for (i = 0; i < nr; i++) {
+		struct sa_subdev_info *subdev = &info->subdev[i];
+		struct resource *res;
+
+		res = platform_get_resource(pdev, IORESOURCE_MEM, i);
+		if (!res)
+			break;
+
+		subdev->map.name = subdev->name;
+		sprintf(subdev->name, "%s-%d", plat->name, i);
+		subdev->plat = plat;
+
+		ret = sa1100_probe_subdev(subdev, res);
+		if (ret)
+			break;
+	}
+
+	info->num_subdev = i;
+
+	/*
+	 * ENXIO is special.  It means we didn't find a chip when we probed.
+	 */
+	if (ret != 0 && !(ret == -ENXIO && info->num_subdev > 0))
+		goto err;
+
+	/*
+	 * If we found one device, don't bother with concat support.  If
+	 * we found multiple devices, use concat if we have it available,
+	 * otherwise fail.  Either way, it'll be called "sa1100".
+	 */
+	if (info->num_subdev == 1) {
+		strcpy(info->subdev[0].name, plat->name);
+		info->mtd = info->subdev[0].mtd;
+		ret = 0;
+	} else if (info->num_subdev > 1) {
+		struct mtd_info *cdev[nr];
+		/*
+		 * We detected multiple devices.  Concatenate them together.
+		 */
+		for (i = 0; i < info->num_subdev; i++)
+			cdev[i] = info->subdev[i].mtd;
+
+		info->mtd = mtd_concat_create(cdev, info->num_subdev,
+					      plat->name);
+		if (info->mtd == NULL)
+			ret = -ENXIO;
+	}
+
+	if (ret == 0)
+		return info;
+
+ err:
+	sa1100_destroy(info, plat);
+ out:
+	return ERR_PTR(ret);
+}
+
+static const char * const part_probes[] = { "cmdlinepart", "RedBoot", NULL };
+
+static int sa1100_mtd_probe(struct platform_device *pdev)
+{
+	struct flash_platform_data *plat = dev_get_platdata(&pdev->dev);
+	struct sa_info *info;
+	int err;
+
+	if (!plat)
+		return -ENODEV;
+
+	info = sa1100_setup_mtd(pdev, plat);
+	if (IS_ERR(info)) {
+		err = PTR_ERR(info);
+		goto out;
+	}
+
+	/*
+	 * Partition selection stuff.
+	 */
+	mtd_device_parse_register(info->mtd, part_probes, NULL, plat->parts,
+				  plat->nr_parts);
+
+	platform_set_drvdata(pdev, info);
+	err = 0;
+
+ out:
+	return err;
+}
+
+static int sa1100_mtd_remove(struct platform_device *pdev)
+{
+	struct sa_info *info = platform_get_drvdata(pdev);
+	struct flash_platform_data *plat = dev_get_platdata(&pdev->dev);
+
+	sa1100_destroy(info, plat);
+
+	return 0;
+}
+
+static struct platform_driver sa1100_mtd_driver = {
+	.probe		= sa1100_mtd_probe,
+	.remove		= sa1100_mtd_remove,
+	.driver		= {
+		.name	= "sa1100-mtd",
+	},
+};
+
+module_platform_driver(sa1100_mtd_driver);
+
+MODULE_AUTHOR("Nicolas Pitre");
+MODULE_DESCRIPTION("SA1100 CFI map driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:sa1100-mtd");
diff --git a/drivers/mtd/maps/sbc_gxx.c b/drivers/mtd/maps/sbc_gxx.c
new file mode 100644
index 000000000..556a2dfe9
--- /dev/null
+++ b/drivers/mtd/maps/sbc_gxx.c
@@ -0,0 +1,236 @@
+/* sbc_gxx.c -- MTD map driver for Arcom Control Systems SBC-MediaGX,
+                SBC-GXm and SBC-GX1 series boards.
+
+   Copyright (C) 2001 Arcom Control System Ltd
+
+   This program is free software; you can redistribute it and/or modify
+   it under the terms of the GNU General Public License as published by
+   the Free Software Foundation; either version 2 of the License, or
+   (at your option) any later version.
+
+   This program is distributed in the hope that it will be useful,
+   but WITHOUT ANY WARRANTY; without even the implied warranty of
+   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+   GNU General Public License for more details.
+
+   You should have received a copy of the GNU General Public License
+   along with this program; if not, write to the Free Software
+   Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
+
+The SBC-MediaGX / SBC-GXx has up to 16 MiB of
+Intel StrataFlash (28F320/28F640) in x8 mode.
+
+This driver uses the CFI probe and Intel Extended Command Set drivers.
+
+The flash is accessed as follows:
+
+   16 KiB memory window at 0xdc000-0xdffff
+
+   Two IO address locations for paging
+
+   0x258
+       bit 0-7: address bit 14-21
+   0x259
+       bit 0-1: address bit 22-23
+       bit 7:   0 - reset/powered down
+                1 - device enabled
+
+The single flash device is divided into 3 partition which appear as
+separate MTD devices.
+
+25/04/2001 AJL (Arcom)  Modified signon strings and partition sizes
+                        (to support bzImages up to 638KiB-ish)
+*/
+
+// Includes
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <asm/io.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+// Defines
+
+// - Hardware specific
+
+#define WINDOW_START 0xdc000
+
+/* Number of bits in offset. */
+#define WINDOW_SHIFT 14
+#define WINDOW_LENGTH (1 << WINDOW_SHIFT)
+
+/* The bits for the offset into the window. */
+#define WINDOW_MASK (WINDOW_LENGTH-1)
+#define PAGE_IO 0x258
+#define PAGE_IO_SIZE 2
+
+/* bit 7 of 0x259 must be 1 to enable device. */
+#define DEVICE_ENABLE 0x8000
+
+// - Flash / Partition sizing
+
+#define MAX_SIZE_KiB             16384
+#define BOOT_PARTITION_SIZE_KiB  768
+#define DATA_PARTITION_SIZE_KiB  1280
+#define APP_PARTITION_SIZE_KiB   6144
+
+// Globals
+
+static volatile int page_in_window = -1; // Current page in window.
+static void __iomem *iomapadr;
+static DEFINE_SPINLOCK(sbc_gxx_spin);
+
+/* partition_info gives details on the logical partitions that the split the
+ * single flash device into. If the size if zero we use up to the end of the
+ * device. */
+static struct mtd_partition partition_info[]={
+    { .name = "SBC-GXx flash boot partition",
+      .offset = 0,
+      .size =   BOOT_PARTITION_SIZE_KiB*1024 },
+    { .name = "SBC-GXx flash data partition",
+      .offset = BOOT_PARTITION_SIZE_KiB*1024,
+      .size = (DATA_PARTITION_SIZE_KiB)*1024 },
+    { .name = "SBC-GXx flash application partition",
+      .offset = (BOOT_PARTITION_SIZE_KiB+DATA_PARTITION_SIZE_KiB)*1024 }
+};
+
+#define NUM_PARTITIONS 3
+
+static inline void sbc_gxx_page(struct map_info *map, unsigned long ofs)
+{
+	unsigned long page = ofs >> WINDOW_SHIFT;
+
+	if( page!=page_in_window ) {
+		outw( page | DEVICE_ENABLE, PAGE_IO );
+		page_in_window = page;
+	}
+}
+
+
+static map_word sbc_gxx_read8(struct map_info *map, unsigned long ofs)
+{
+	map_word ret;
+	spin_lock(&sbc_gxx_spin);
+	sbc_gxx_page(map, ofs);
+	ret.x[0] = readb(iomapadr + (ofs & WINDOW_MASK));
+	spin_unlock(&sbc_gxx_spin);
+	return ret;
+}
+
+static void sbc_gxx_copy_from(struct map_info *map, void *to, unsigned long from, ssize_t len)
+{
+	while(len) {
+		unsigned long thislen = len;
+		if (len > (WINDOW_LENGTH - (from & WINDOW_MASK)))
+			thislen = WINDOW_LENGTH-(from & WINDOW_MASK);
+
+		spin_lock(&sbc_gxx_spin);
+		sbc_gxx_page(map, from);
+		memcpy_fromio(to, iomapadr + (from & WINDOW_MASK), thislen);
+		spin_unlock(&sbc_gxx_spin);
+		to += thislen;
+		from += thislen;
+		len -= thislen;
+	}
+}
+
+static void sbc_gxx_write8(struct map_info *map, map_word d, unsigned long adr)
+{
+	spin_lock(&sbc_gxx_spin);
+	sbc_gxx_page(map, adr);
+	writeb(d.x[0], iomapadr + (adr & WINDOW_MASK));
+	spin_unlock(&sbc_gxx_spin);
+}
+
+static void sbc_gxx_copy_to(struct map_info *map, unsigned long to, const void *from, ssize_t len)
+{
+	while(len) {
+		unsigned long thislen = len;
+		if (len > (WINDOW_LENGTH - (to & WINDOW_MASK)))
+			thislen = WINDOW_LENGTH-(to & WINDOW_MASK);
+
+		spin_lock(&sbc_gxx_spin);
+		sbc_gxx_page(map, to);
+		memcpy_toio(iomapadr + (to & WINDOW_MASK), from, thislen);
+		spin_unlock(&sbc_gxx_spin);
+		to += thislen;
+		from += thislen;
+		len -= thislen;
+	}
+}
+
+static struct map_info sbc_gxx_map = {
+	.name = "SBC-GXx flash",
+	.phys = NO_XIP,
+	.size = MAX_SIZE_KiB*1024, /* this must be set to a maximum possible amount
+			 of flash so the cfi probe routines find all
+			 the chips */
+	.bankwidth = 1,
+	.read = sbc_gxx_read8,
+	.copy_from = sbc_gxx_copy_from,
+	.write = sbc_gxx_write8,
+	.copy_to = sbc_gxx_copy_to
+};
+
+/* MTD device for all of the flash. */
+static struct mtd_info *all_mtd;
+
+static void cleanup_sbc_gxx(void)
+{
+	if( all_mtd ) {
+		mtd_device_unregister(all_mtd);
+		map_destroy( all_mtd );
+	}
+
+	iounmap(iomapadr);
+	release_region(PAGE_IO,PAGE_IO_SIZE);
+}
+
+static int __init init_sbc_gxx(void)
+{
+  	iomapadr = ioremap(WINDOW_START, WINDOW_LENGTH);
+	if (!iomapadr) {
+		printk( KERN_ERR"%s: failed to ioremap memory region\n",
+			sbc_gxx_map.name );
+		return -EIO;
+	}
+
+	if (!request_region( PAGE_IO, PAGE_IO_SIZE, "SBC-GXx flash")) {
+		printk( KERN_ERR"%s: IO ports 0x%x-0x%x in use\n",
+			sbc_gxx_map.name,
+			PAGE_IO, PAGE_IO+PAGE_IO_SIZE-1 );
+		iounmap(iomapadr);
+		return -EAGAIN;
+	}
+
+
+	printk( KERN_INFO"%s: IO:0x%x-0x%x MEM:0x%x-0x%x\n",
+		sbc_gxx_map.name,
+		PAGE_IO, PAGE_IO+PAGE_IO_SIZE-1,
+		WINDOW_START, WINDOW_START+WINDOW_LENGTH-1 );
+
+	/* Probe for chip. */
+	all_mtd = do_map_probe( "cfi_probe", &sbc_gxx_map );
+	if( !all_mtd ) {
+		cleanup_sbc_gxx();
+		return -ENXIO;
+	}
+
+	all_mtd->owner = THIS_MODULE;
+
+	/* Create MTD devices for each partition. */
+	mtd_device_register(all_mtd, partition_info, NUM_PARTITIONS);
+
+	return 0;
+}
+
+module_init(init_sbc_gxx);
+module_exit(cleanup_sbc_gxx);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Arcom Control Systems Ltd.");
+MODULE_DESCRIPTION("MTD map driver for SBC-GXm and SBC-GX1 series boards");
diff --git a/drivers/mtd/maps/sc520cdp.c b/drivers/mtd/maps/sc520cdp.c
new file mode 100644
index 000000000..093edd51b
--- /dev/null
+++ b/drivers/mtd/maps/sc520cdp.c
@@ -0,0 +1,302 @@
+/* sc520cdp.c -- MTD map driver for AMD SC520 Customer Development Platform
+ *
+ * Copyright (C) 2001 Sysgo Real-Time Solutions GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
+ *
+ *
+ * The SC520CDP is an evaluation board for the Elan SC520 processor available
+ * from AMD. It has two banks of 32-bit Flash ROM, each 8 Megabytes in size,
+ * and up to 512 KiB of 8-bit DIL Flash ROM.
+ * For details see http://www.amd.com/products/epd/desiging/evalboards/18.elansc520/520_cdp_brief/index.html
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/concat.h>
+
+/*
+** The Embedded Systems BIOS decodes the first FLASH starting at
+** 0x8400000. This is a *terrible* place for it because accessing
+** the flash at this location causes the A22 address line to be high
+** (that's what 0x8400000 binary's ought to be). But this is the highest
+** order address line on the raw flash devices themselves!!
+** This causes the top HALF of the flash to be accessed first. Beyond
+** the physical limits of the flash, the flash chip aliases over (to
+** 0x880000 which causes the bottom half to be accessed. This splits the
+** flash into two and inverts it! If you then try to access this from another
+** program that does NOT do this insanity, then you *will* access the
+** first half of the flash, but not find what you expect there. That
+** stuff is in the *second* half! Similarly, the address used by the
+** BIOS for the second FLASH bank is also quite a bad choice.
+** If REPROGRAM_PAR is defined below (the default), then this driver will
+** choose more useful addresses for the FLASH banks by reprogramming the
+** responsible PARxx registers in the SC520's MMCR region. This will
+** cause the settings to be incompatible with the BIOS's settings, which
+** shouldn't be a problem since you are running Linux, (i.e. the BIOS is
+** not much use anyway). However, if you need to be compatible with
+** the BIOS for some reason, just undefine REPROGRAM_PAR.
+*/
+#define REPROGRAM_PAR
+
+
+
+#ifdef REPROGRAM_PAR
+
+/* These are the addresses we want.. */
+#define WINDOW_ADDR_0	0x08800000
+#define WINDOW_ADDR_1	0x09000000
+#define WINDOW_ADDR_2	0x09800000
+
+/* .. and these are the addresses the BIOS gives us */
+#define WINDOW_ADDR_0_BIOS	0x08400000
+#define WINDOW_ADDR_1_BIOS	0x08c00000
+#define WINDOW_ADDR_2_BIOS	0x09400000
+
+#else
+
+#define WINDOW_ADDR_0	0x08400000
+#define WINDOW_ADDR_1	0x08C00000
+#define WINDOW_ADDR_2	0x09400000
+
+#endif
+
+#define WINDOW_SIZE_0	0x00800000
+#define WINDOW_SIZE_1	0x00800000
+#define WINDOW_SIZE_2	0x00080000
+
+
+static struct map_info sc520cdp_map[] = {
+	{
+		.name = "SC520CDP Flash Bank #0",
+		.size = WINDOW_SIZE_0,
+		.bankwidth = 4,
+		.phys = WINDOW_ADDR_0
+	},
+	{
+		.name = "SC520CDP Flash Bank #1",
+		.size = WINDOW_SIZE_1,
+		.bankwidth = 4,
+		.phys = WINDOW_ADDR_1
+	},
+	{
+		.name = "SC520CDP DIL Flash",
+		.size = WINDOW_SIZE_2,
+		.bankwidth = 1,
+		.phys = WINDOW_ADDR_2
+	},
+};
+
+#define NUM_FLASH_BANKS	ARRAY_SIZE(sc520cdp_map)
+
+static struct mtd_info *mymtd[NUM_FLASH_BANKS];
+static struct mtd_info *merged_mtd;
+
+#ifdef REPROGRAM_PAR
+
+/*
+** The SC520 MMCR (memory mapped control register) region resides
+** at 0xFFFEF000. The 16 Programmable Address Region (PAR) registers
+** are at offset 0x88 in the MMCR:
+*/
+#define SC520_MMCR_BASE		0xFFFEF000
+#define SC520_MMCR_EXTENT	0x1000
+#define SC520_PAR(x)		((0x88/sizeof(unsigned long)) + (x))
+#define NUM_SC520_PAR		16	/* total number of PAR registers */
+
+/*
+** The highest three bits in a PAR register determine what target
+** device is controlled by this PAR. Here, only ROMCS? and BOOTCS
+** devices are of interest.
+*/
+#define SC520_PAR_BOOTCS	(0x4<<29)
+#define SC520_PAR_ROMCS0	(0x5<<29)
+#define SC520_PAR_ROMCS1	(0x6<<29)
+#define SC520_PAR_TRGDEV	(0x7<<29)
+
+/*
+** Bits 28 thru 26 determine some attributes for the
+** region controlled by the PAR. (We only use non-cacheable)
+*/
+#define SC520_PAR_WRPROT	(1<<26)	/* write protected       */
+#define SC520_PAR_NOCACHE	(1<<27)	/* non-cacheable         */
+#define SC520_PAR_NOEXEC	(1<<28)	/* code execution denied */
+
+
+/*
+** Bit 25 determines the granularity: 4K or 64K
+*/
+#define SC520_PAR_PG_SIZ4	(0<<25)
+#define SC520_PAR_PG_SIZ64	(1<<25)
+
+/*
+** Build a value to be written into a PAR register.
+** We only need ROM entries, 64K page size:
+*/
+#define SC520_PAR_ENTRY(trgdev, address, size) \
+	((trgdev) | SC520_PAR_NOCACHE | SC520_PAR_PG_SIZ64 | \
+	(address) >> 16 | (((size) >> 16) - 1) << 14)
+
+struct sc520_par_table
+{
+	unsigned long trgdev;
+	unsigned long new_par;
+	unsigned long default_address;
+};
+
+static const struct sc520_par_table par_table[NUM_FLASH_BANKS] =
+{
+	{	/* Flash Bank #0: selected by ROMCS0 */
+		SC520_PAR_ROMCS0,
+		SC520_PAR_ENTRY(SC520_PAR_ROMCS0, WINDOW_ADDR_0, WINDOW_SIZE_0),
+		WINDOW_ADDR_0_BIOS
+	},
+	{	/* Flash Bank #1: selected by ROMCS1 */
+		SC520_PAR_ROMCS1,
+		SC520_PAR_ENTRY(SC520_PAR_ROMCS1, WINDOW_ADDR_1, WINDOW_SIZE_1),
+		WINDOW_ADDR_1_BIOS
+	},
+	{	/* DIL (BIOS) Flash: selected by BOOTCS */
+		SC520_PAR_BOOTCS,
+		SC520_PAR_ENTRY(SC520_PAR_BOOTCS, WINDOW_ADDR_2, WINDOW_SIZE_2),
+		WINDOW_ADDR_2_BIOS
+	}
+};
+
+
+static void sc520cdp_setup_par(void)
+{
+	unsigned long __iomem *mmcr;
+	unsigned long mmcr_val;
+	int i, j;
+
+	/* map in SC520's MMCR area */
+	mmcr = ioremap_nocache(SC520_MMCR_BASE, SC520_MMCR_EXTENT);
+	if(!mmcr) { /* ioremap_nocache failed: skip the PAR reprogramming */
+		/* force physical address fields to BIOS defaults: */
+		for(i = 0; i < NUM_FLASH_BANKS; i++)
+			sc520cdp_map[i].phys = par_table[i].default_address;
+		return;
+	}
+
+	/*
+	** Find the PARxx registers that are responsible for activating
+	** ROMCS0, ROMCS1 and BOOTCS. Reprogram each of these with a
+	** new value from the table.
+	*/
+	for(i = 0; i < NUM_FLASH_BANKS; i++) {		/* for each par_table entry  */
+		for(j = 0; j < NUM_SC520_PAR; j++) {	/* for each PAR register     */
+			mmcr_val = readl(&mmcr[SC520_PAR(j)]);
+			/* if target device field matches, reprogram the PAR */
+			if((mmcr_val & SC520_PAR_TRGDEV) == par_table[i].trgdev)
+			{
+				writel(par_table[i].new_par, &mmcr[SC520_PAR(j)]);
+				break;
+			}
+		}
+		if(j == NUM_SC520_PAR)
+		{	/* no matching PAR found: try default BIOS address */
+			printk(KERN_NOTICE "Could not find PAR responsible for %s\n",
+				sc520cdp_map[i].name);
+			printk(KERN_NOTICE "Trying default address 0x%lx\n",
+				par_table[i].default_address);
+			sc520cdp_map[i].phys = par_table[i].default_address;
+		}
+	}
+	iounmap(mmcr);
+}
+#endif
+
+
+static int __init init_sc520cdp(void)
+{
+	int i, devices_found = 0;
+
+#ifdef REPROGRAM_PAR
+	/* reprogram PAR registers so flash appears at the desired addresses */
+	sc520cdp_setup_par();
+#endif
+
+	for (i = 0; i < NUM_FLASH_BANKS; i++) {
+		printk(KERN_NOTICE "SC520 CDP flash device: 0x%Lx at 0x%Lx\n",
+			(unsigned long long)sc520cdp_map[i].size,
+			(unsigned long long)sc520cdp_map[i].phys);
+
+		sc520cdp_map[i].virt = ioremap_nocache(sc520cdp_map[i].phys, sc520cdp_map[i].size);
+
+		if (!sc520cdp_map[i].virt) {
+			printk("Failed to ioremap_nocache\n");
+			return -EIO;
+		}
+
+		simple_map_init(&sc520cdp_map[i]);
+
+		mymtd[i] = do_map_probe("cfi_probe", &sc520cdp_map[i]);
+		if(!mymtd[i])
+			mymtd[i] = do_map_probe("jedec_probe", &sc520cdp_map[i]);
+		if(!mymtd[i])
+			mymtd[i] = do_map_probe("map_rom", &sc520cdp_map[i]);
+
+		if (mymtd[i]) {
+			mymtd[i]->owner = THIS_MODULE;
+			++devices_found;
+		}
+		else {
+			iounmap(sc520cdp_map[i].virt);
+		}
+	}
+	if(devices_found >= 2) {
+		/* Combine the two flash banks into a single MTD device & register it: */
+		merged_mtd = mtd_concat_create(mymtd, 2, "SC520CDP Flash Banks #0 and #1");
+		if(merged_mtd)
+			mtd_device_register(merged_mtd, NULL, 0);
+	}
+	if(devices_found == 3) /* register the third (DIL-Flash) device */
+		mtd_device_register(mymtd[2], NULL, 0);
+	return(devices_found ? 0 : -ENXIO);
+}
+
+static void __exit cleanup_sc520cdp(void)
+{
+	int i;
+
+	if (merged_mtd) {
+		mtd_device_unregister(merged_mtd);
+		mtd_concat_destroy(merged_mtd);
+	}
+	if (mymtd[2])
+		mtd_device_unregister(mymtd[2]);
+
+	for (i = 0; i < NUM_FLASH_BANKS; i++) {
+		if (mymtd[i])
+			map_destroy(mymtd[i]);
+		if (sc520cdp_map[i].virt) {
+			iounmap(sc520cdp_map[i].virt);
+			sc520cdp_map[i].virt = NULL;
+		}
+	}
+}
+
+module_init(init_sc520cdp);
+module_exit(cleanup_sc520cdp);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Sysgo Real-Time Solutions GmbH");
+MODULE_DESCRIPTION("MTD map driver for AMD SC520 Customer Development Platform");
diff --git a/drivers/mtd/maps/scb2_flash.c b/drivers/mtd/maps/scb2_flash.c
new file mode 100644
index 000000000..b7a22a612
--- /dev/null
+++ b/drivers/mtd/maps/scb2_flash.c
@@ -0,0 +1,238 @@
+/*
+ * MTD map driver for BIOS Flash on Intel SCB2 boards
+ * Copyright (C) 2002 Sun Microsystems, Inc.
+ * Tim Hockin <thockin@sun.com>
+ *
+ * A few notes on this MTD map:
+ *
+ * This was developed with a small number of SCB2 boards to test on.
+ * Hopefully, Intel has not introducted too many unaccounted variables in the
+ * making of this board.
+ *
+ * The BIOS marks its own memory region as 'reserved' in the e820 map.  We
+ * try to request it here, but if it fails, we carry on anyway.
+ *
+ * This is how the chip is attached, so said the schematic:
+ * * a 4 MiB (32 Mib) 16 bit chip
+ * * a 1 MiB memory region
+ * * A20 and A21 pulled up
+ * * D8-D15 ignored
+ * What this means is that, while we are addressing bytes linearly, we are
+ * really addressing words, and discarding the other byte.  This means that
+ * the chip MUST BE at least 2 MiB.  This also means that every block is
+ * actually half as big as the chip reports.  It also means that accesses of
+ * logical address 0 hit higher-address sections of the chip, not physical 0.
+ * One can only hope that these 4MiB x16 chips were a lot cheaper than 1MiB x8
+ * chips.
+ *
+ * This driver assumes the chip is not write-protected by an external signal.
+ * As of the this writing, that is true, but may change, just to spite me.
+ *
+ * The actual BIOS layout has been mostly reverse engineered.  Intel BIOS
+ * updates for this board include 10 related (*.bio - &.bi9) binary files and
+ * another separate (*.bbo) binary file.  The 10 files are 64k of data + a
+ * small header.  If the headers are stripped off, the 10 64k files can be
+ * concatenated into a 640k image.  This is your BIOS image, proper.  The
+ * separate .bbo file also has a small header.  It is the 'Boot Block'
+ * recovery BIOS.  Once the header is stripped, no further prep is needed.
+ * As best I can tell, the BIOS is arranged as such:
+ * offset 0x00000 to 0x4ffff (320k):  unknown - SCSI BIOS, etc?
+ * offset 0x50000 to 0xeffff (640k):  BIOS proper
+ * offset 0xf0000 ty 0xfffff (64k):   Boot Block region
+ *
+ * Intel's BIOS update program flashes the BIOS and Boot Block in separate
+ * steps.  Probably a wise thing to do.
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/cfi.h>
+#include <linux/pci.h>
+#include <linux/pci_ids.h>
+
+#define MODNAME		"scb2_flash"
+#define SCB2_ADDR	0xfff00000
+#define SCB2_WINDOW	0x00100000
+
+
+static void __iomem *scb2_ioaddr;
+static struct mtd_info *scb2_mtd;
+static struct map_info scb2_map = {
+	.name =      "SCB2 BIOS Flash",
+	.size =      0,
+	.bankwidth =  1,
+};
+static int region_fail;
+
+static int scb2_fixup_mtd(struct mtd_info *mtd)
+{
+	int i;
+	int done = 0;
+	struct map_info *map = mtd->priv;
+	struct cfi_private *cfi = map->fldrv_priv;
+
+	/* barf if this doesn't look right */
+	if (cfi->cfiq->InterfaceDesc != CFI_INTERFACE_X16_ASYNC) {
+		printk(KERN_ERR MODNAME ": unsupported InterfaceDesc: %#x\n",
+		    cfi->cfiq->InterfaceDesc);
+		return -1;
+	}
+
+	/* I wasn't here. I didn't see. dwmw2. */
+
+	/* the chip is sometimes bigger than the map - what a waste */
+	mtd->size = map->size;
+
+	/*
+	 * We only REALLY get half the chip, due to the way it is
+	 * wired up - D8-D15 are tossed away.  We read linear bytes,
+	 * but in reality we are getting 1/2 of each 16-bit read,
+	 * which LOOKS linear to us.  Because CFI code accounts for
+	 * things like lock/unlock/erase by eraseregions, we need to
+	 * fudge them to reflect this.  Erases go like this:
+	 *   * send an erase to an address
+	 *   * the chip samples the address and erases the block
+	 *   * add the block erasesize to the address and repeat
+	 *   -- the problem is that addresses are 16-bit addressable
+	 *   -- we end up erasing every-other block
+	 */
+	mtd->erasesize /= 2;
+	for (i = 0; i < mtd->numeraseregions; i++) {
+		struct mtd_erase_region_info *region = &mtd->eraseregions[i];
+		region->erasesize /= 2;
+	}
+
+	/*
+	 * If the chip is bigger than the map, it is wired with the high
+	 * address lines pulled up.  This makes us access the top portion of
+	 * the chip, so all our erase-region info is wrong.  Start cutting from
+	 * the bottom.
+	 */
+	for (i = 0; !done && i < mtd->numeraseregions; i++) {
+		struct mtd_erase_region_info *region = &mtd->eraseregions[i];
+
+		if (region->numblocks * region->erasesize > mtd->size) {
+			region->numblocks = ((unsigned long)mtd->size /
+						region->erasesize);
+			done = 1;
+		} else {
+			region->numblocks = 0;
+		}
+		region->offset = 0;
+	}
+
+	return 0;
+}
+
+/* CSB5's 'Function Control Register' has bits for decoding @ >= 0xffc00000 */
+#define CSB5_FCR	0x41
+#define CSB5_FCR_DECODE_ALL 0x0e
+static int scb2_flash_probe(struct pci_dev *dev,
+			    const struct pci_device_id *ent)
+{
+	u8 reg;
+
+	/* enable decoding of the flash region in the south bridge */
+	pci_read_config_byte(dev, CSB5_FCR, &reg);
+	pci_write_config_byte(dev, CSB5_FCR, reg | CSB5_FCR_DECODE_ALL);
+
+	if (!request_mem_region(SCB2_ADDR, SCB2_WINDOW, scb2_map.name)) {
+		/*
+		 * The BIOS seems to mark the flash region as 'reserved'
+		 * in the e820 map.  Warn and go about our business.
+		 */
+		printk(KERN_WARNING MODNAME
+		    ": warning - can't reserve rom window, continuing\n");
+		region_fail = 1;
+	}
+
+	/* remap the IO window (w/o caching) */
+	scb2_ioaddr = ioremap_nocache(SCB2_ADDR, SCB2_WINDOW);
+	if (!scb2_ioaddr) {
+		printk(KERN_ERR MODNAME ": Failed to ioremap window!\n");
+		if (!region_fail)
+			release_mem_region(SCB2_ADDR, SCB2_WINDOW);
+		return -ENOMEM;
+	}
+
+	scb2_map.phys = SCB2_ADDR;
+	scb2_map.virt = scb2_ioaddr;
+	scb2_map.size = SCB2_WINDOW;
+
+	simple_map_init(&scb2_map);
+
+	/* try to find a chip */
+	scb2_mtd = do_map_probe("cfi_probe", &scb2_map);
+
+	if (!scb2_mtd) {
+		printk(KERN_ERR MODNAME ": flash probe failed!\n");
+		iounmap(scb2_ioaddr);
+		if (!region_fail)
+			release_mem_region(SCB2_ADDR, SCB2_WINDOW);
+		return -ENODEV;
+	}
+
+	scb2_mtd->owner = THIS_MODULE;
+	if (scb2_fixup_mtd(scb2_mtd) < 0) {
+		mtd_device_unregister(scb2_mtd);
+		map_destroy(scb2_mtd);
+		iounmap(scb2_ioaddr);
+		if (!region_fail)
+			release_mem_region(SCB2_ADDR, SCB2_WINDOW);
+		return -ENODEV;
+	}
+
+	printk(KERN_NOTICE MODNAME ": chip size 0x%llx at offset 0x%llx\n",
+	       (unsigned long long)scb2_mtd->size,
+	       (unsigned long long)(SCB2_WINDOW - scb2_mtd->size));
+
+	mtd_device_register(scb2_mtd, NULL, 0);
+
+	return 0;
+}
+
+static void scb2_flash_remove(struct pci_dev *dev)
+{
+	if (!scb2_mtd)
+		return;
+
+	/* disable flash writes */
+	mtd_lock(scb2_mtd, 0, scb2_mtd->size);
+
+	mtd_device_unregister(scb2_mtd);
+	map_destroy(scb2_mtd);
+
+	iounmap(scb2_ioaddr);
+	scb2_ioaddr = NULL;
+
+	if (!region_fail)
+		release_mem_region(SCB2_ADDR, SCB2_WINDOW);
+}
+
+static struct pci_device_id scb2_flash_pci_ids[] = {
+	{
+	  .vendor = PCI_VENDOR_ID_SERVERWORKS,
+	  .device = PCI_DEVICE_ID_SERVERWORKS_CSB5,
+	  .subvendor = PCI_ANY_ID,
+	  .subdevice = PCI_ANY_ID
+	},
+	{ 0, }
+};
+
+static struct pci_driver scb2_flash_driver = {
+	.name =     "Intel SCB2 BIOS Flash",
+	.id_table = scb2_flash_pci_ids,
+	.probe =    scb2_flash_probe,
+	.remove =   scb2_flash_remove,
+};
+
+module_pci_driver(scb2_flash_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Tim Hockin <thockin@sun.com>");
+MODULE_DESCRIPTION("MTD map driver for Intel SCB2 BIOS Flash");
+MODULE_DEVICE_TABLE(pci, scb2_flash_pci_ids);
diff --git a/drivers/mtd/maps/scx200_docflash.c b/drivers/mtd/maps/scx200_docflash.c
new file mode 100644
index 000000000..f1c1f737d
--- /dev/null
+++ b/drivers/mtd/maps/scx200_docflash.c
@@ -0,0 +1,225 @@
+/* linux/drivers/mtd/maps/scx200_docflash.c
+
+   Copyright (c) 2001,2002 Christer Weinigel <wingel@nano-system.com>
+
+   National Semiconductor SCx200 flash mapped with DOCCS
+*/
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+
+#include <linux/pci.h>
+#include <linux/scx200.h>
+
+#define NAME "scx200_docflash"
+
+MODULE_AUTHOR("Christer Weinigel <wingel@hack.org>");
+MODULE_DESCRIPTION("NatSemi SCx200 DOCCS Flash Driver");
+MODULE_LICENSE("GPL");
+
+static int probe = 0;		/* Don't autoprobe */
+static unsigned size = 0x1000000; /* 16 MiB the whole ISA address space */
+static unsigned width = 8;	/* Default to 8 bits wide */
+static char *flashtype = "cfi_probe";
+
+module_param(probe, int, 0);
+MODULE_PARM_DESC(probe, "Probe for a BIOS mapping");
+module_param(size, int, 0);
+MODULE_PARM_DESC(size, "Size of the flash mapping");
+module_param(width, int, 0);
+MODULE_PARM_DESC(width, "Data width of the flash mapping (8/16)");
+module_param(flashtype, charp, 0);
+MODULE_PARM_DESC(flashtype, "Type of MTD probe to do");
+
+static struct resource docmem = {
+	.flags = IORESOURCE_MEM,
+	.name  = "NatSemi SCx200 DOCCS Flash",
+};
+
+static struct mtd_info *mymtd;
+
+static struct mtd_partition partition_info[] = {
+	{
+		.name   = "DOCCS Boot kernel",
+		.offset = 0,
+		.size   = 0xc0000
+	},
+	{
+		.name   = "DOCCS Low BIOS",
+		.offset = 0xc0000,
+		.size   = 0x40000
+	},
+	{
+		.name   = "DOCCS File system",
+		.offset = 0x100000,
+		.size   = ~0	/* calculate from flash size */
+	},
+	{
+		.name   = "DOCCS High BIOS",
+		.offset = ~0, 	/* calculate from flash size */
+		.size   = 0x80000
+	},
+};
+#define NUM_PARTITIONS ARRAY_SIZE(partition_info)
+
+static struct map_info scx200_docflash_map = {
+	.name      = "NatSemi SCx200 DOCCS Flash",
+};
+
+static int __init init_scx200_docflash(void)
+{
+	unsigned u;
+	unsigned base;
+	unsigned ctrl;
+	unsigned pmr;
+	struct pci_dev *bridge;
+
+	printk(KERN_DEBUG NAME ": NatSemi SCx200 DOCCS Flash Driver\n");
+
+	if ((bridge = pci_get_device(PCI_VENDOR_ID_NS,
+				      PCI_DEVICE_ID_NS_SCx200_BRIDGE,
+				      NULL)) == NULL)
+		return -ENODEV;
+
+	/* check that we have found the configuration block */
+	if (!scx200_cb_present()) {
+		pci_dev_put(bridge);
+		return -ENODEV;
+	}
+
+	if (probe) {
+		/* Try to use the present flash mapping if any */
+		pci_read_config_dword(bridge, SCx200_DOCCS_BASE, &base);
+		pci_read_config_dword(bridge, SCx200_DOCCS_CTRL, &ctrl);
+		pci_dev_put(bridge);
+
+		pmr = inl(scx200_cb_base + SCx200_PMR);
+
+		if (base == 0
+		    || (ctrl & 0x07000000) != 0x07000000
+		    || (ctrl & 0x0007ffff) == 0)
+			return -ENODEV;
+
+		size = ((ctrl&0x1fff)<<13) + (1<<13);
+
+		for (u = size; u > 1; u >>= 1)
+			;
+		if (u != 1)
+			return -ENODEV;
+
+		if (pmr & (1<<6))
+			width = 16;
+		else
+			width = 8;
+
+		docmem.start = base;
+		docmem.end = base + size;
+
+		if (request_resource(&iomem_resource, &docmem)) {
+			printk(KERN_ERR NAME ": unable to allocate memory for flash mapping\n");
+			return -ENOMEM;
+		}
+	} else {
+		pci_dev_put(bridge);
+		for (u = size; u > 1; u >>= 1)
+			;
+		if (u != 1) {
+			printk(KERN_ERR NAME ": invalid size for flash mapping\n");
+			return -EINVAL;
+		}
+
+		if (width != 8 && width != 16) {
+			printk(KERN_ERR NAME ": invalid bus width for flash mapping\n");
+			return -EINVAL;
+		}
+
+		if (allocate_resource(&iomem_resource, &docmem,
+				      size,
+				      0xc0000000, 0xffffffff,
+				      size, NULL, NULL)) {
+			printk(KERN_ERR NAME ": unable to allocate memory for flash mapping\n");
+			return -ENOMEM;
+		}
+
+		ctrl = 0x07000000 | ((size-1) >> 13);
+
+		printk(KERN_INFO "DOCCS BASE=0x%08lx, CTRL=0x%08lx\n", (long)docmem.start, (long)ctrl);
+
+		pci_write_config_dword(bridge, SCx200_DOCCS_BASE, docmem.start);
+		pci_write_config_dword(bridge, SCx200_DOCCS_CTRL, ctrl);
+		pmr = inl(scx200_cb_base + SCx200_PMR);
+
+		if (width == 8) {
+			pmr &= ~(1<<6);
+		} else {
+			pmr |= (1<<6);
+		}
+		outl(pmr, scx200_cb_base + SCx200_PMR);
+	}
+
+	printk(KERN_INFO NAME ": DOCCS mapped at %pR, width %d\n",
+	       &docmem, width);
+
+	scx200_docflash_map.size = size;
+	if (width == 8)
+		scx200_docflash_map.bankwidth = 1;
+	else
+		scx200_docflash_map.bankwidth = 2;
+
+	simple_map_init(&scx200_docflash_map);
+
+	scx200_docflash_map.phys = docmem.start;
+	scx200_docflash_map.virt = ioremap(docmem.start, scx200_docflash_map.size);
+	if (!scx200_docflash_map.virt) {
+		printk(KERN_ERR NAME ": failed to ioremap the flash\n");
+		release_resource(&docmem);
+		return -EIO;
+	}
+
+	mymtd = do_map_probe(flashtype, &scx200_docflash_map);
+	if (!mymtd) {
+		printk(KERN_ERR NAME ": unable to detect flash\n");
+		iounmap(scx200_docflash_map.virt);
+		release_resource(&docmem);
+		return -ENXIO;
+	}
+
+	if (size < mymtd->size)
+		printk(KERN_WARNING NAME ": warning, flash mapping is smaller than flash size\n");
+
+	mymtd->owner = THIS_MODULE;
+
+	partition_info[3].offset = mymtd->size-partition_info[3].size;
+	partition_info[2].size = partition_info[3].offset-partition_info[2].offset;
+	mtd_device_register(mymtd, partition_info, NUM_PARTITIONS);
+
+	return 0;
+}
+
+static void __exit cleanup_scx200_docflash(void)
+{
+	if (mymtd) {
+		mtd_device_unregister(mymtd);
+		map_destroy(mymtd);
+	}
+	if (scx200_docflash_map.virt) {
+		iounmap(scx200_docflash_map.virt);
+		release_resource(&docmem);
+	}
+}
+
+module_init(init_scx200_docflash);
+module_exit(cleanup_scx200_docflash);
+
+/*
+    Local variables:
+        compile-command: "make -k -C ../../.. SUBDIRS=drivers/mtd/maps modules"
+        c-basic-offset: 8
+    End:
+*/
diff --git a/drivers/mtd/maps/solutionengine.c b/drivers/mtd/maps/solutionengine.c
new file mode 100644
index 000000000..bb580bc16
--- /dev/null
+++ b/drivers/mtd/maps/solutionengine.c
@@ -0,0 +1,95 @@
+/*
+ * Flash and EPROM on Hitachi Solution Engine and similar boards.
+ *
+ * (C) 2001 Red Hat, Inc.
+ *
+ * GPL'd
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <asm/io.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <linux/errno.h>
+
+static struct mtd_info *flash_mtd;
+static struct mtd_info *eprom_mtd;
+
+struct map_info soleng_eprom_map = {
+	.name = "Solution Engine EPROM",
+	.size = 0x400000,
+	.bankwidth = 4,
+};
+
+struct map_info soleng_flash_map = {
+	.name = "Solution Engine FLASH",
+	.size = 0x400000,
+	.bankwidth = 4,
+};
+
+static const char * const probes[] = { "RedBoot", "cmdlinepart", NULL };
+
+static int __init init_soleng_maps(void)
+{
+	/* First probe at offset 0 */
+	soleng_flash_map.phys = 0;
+	soleng_flash_map.virt = (void __iomem *)P2SEGADDR(0);
+	soleng_eprom_map.phys = 0x01000000;
+	soleng_eprom_map.virt = (void __iomem *)P1SEGADDR(0x01000000);
+	simple_map_init(&soleng_eprom_map);
+	simple_map_init(&soleng_flash_map);
+
+	printk(KERN_NOTICE "Probing for flash chips at 0x00000000:\n");
+	flash_mtd = do_map_probe("cfi_probe", &soleng_flash_map);
+	if (!flash_mtd) {
+		/* Not there. Try swapping */
+		printk(KERN_NOTICE "Probing for flash chips at 0x01000000:\n");
+		soleng_flash_map.phys = 0x01000000;
+		soleng_flash_map.virt = P2SEGADDR(0x01000000);
+		soleng_eprom_map.phys = 0;
+		soleng_eprom_map.virt = P1SEGADDR(0);
+		flash_mtd = do_map_probe("cfi_probe", &soleng_flash_map);
+		if (!flash_mtd) {
+			/* Eep. */
+			printk(KERN_NOTICE "Flash chips not detected at either possible location.\n");
+			return -ENXIO;
+		}
+	}
+	printk(KERN_NOTICE "Solution Engine: Flash at 0x%08lx, EPROM at 0x%08lx\n",
+	       soleng_flash_map.phys & 0x1fffffff,
+	       soleng_eprom_map.phys & 0x1fffffff);
+	flash_mtd->owner = THIS_MODULE;
+
+	eprom_mtd = do_map_probe("map_rom", &soleng_eprom_map);
+	if (eprom_mtd) {
+		eprom_mtd->owner = THIS_MODULE;
+		mtd_device_register(eprom_mtd, NULL, 0);
+	}
+
+	mtd_device_parse_register(flash_mtd, probes, NULL, NULL, 0);
+
+	return 0;
+}
+
+static void __exit cleanup_soleng_maps(void)
+{
+	if (eprom_mtd) {
+		mtd_device_unregister(eprom_mtd);
+		map_destroy(eprom_mtd);
+	}
+
+	mtd_device_unregister(flash_mtd);
+	map_destroy(flash_mtd);
+}
+
+module_init(init_soleng_maps);
+module_exit(cleanup_soleng_maps);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("David Woodhouse <dwmw2@infradead.org>");
+MODULE_DESCRIPTION("MTD map driver for Hitachi SolutionEngine (and similar) boards");
+
diff --git a/drivers/mtd/maps/sun_uflash.c b/drivers/mtd/maps/sun_uflash.c
new file mode 100644
index 000000000..d459aca07
--- /dev/null
+++ b/drivers/mtd/maps/sun_uflash.c
@@ -0,0 +1,159 @@
+/* sun_uflash.c - Driver for user-programmable flash on
+ *                Sun Microsystems SME boardsets.
+ *
+ * This driver does NOT provide access to the OBP-flash for
+ * safety reasons-- use <linux>/drivers/sbus/char/flash.c instead.
+ *
+ * Copyright (c) 2001 Eric Brower (ebrower@usa.net)
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/fs.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+#include <asm/prom.h>
+#include <asm/uaccess.h>
+#include <asm/io.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+
+#define UFLASH_OBPNAME	"flashprom"
+#define DRIVER_NAME	"sun_uflash"
+#define PFX		DRIVER_NAME ": "
+
+#define UFLASH_WINDOW_SIZE	0x200000
+#define UFLASH_BUSWIDTH		1			/* EBus is 8-bit */
+
+MODULE_AUTHOR("Eric Brower <ebrower@usa.net>");
+MODULE_DESCRIPTION("User-programmable flash device on Sun Microsystems boardsets");
+MODULE_SUPPORTED_DEVICE(DRIVER_NAME);
+MODULE_LICENSE("GPL");
+MODULE_VERSION("2.1");
+
+struct uflash_dev {
+	const char		*name;	/* device name */
+	struct map_info 	map;	/* mtd map info */
+	struct mtd_info		*mtd;	/* mtd info */
+};
+
+struct map_info uflash_map_templ = {
+	.name =		"SUNW,???-????",
+	.size =		UFLASH_WINDOW_SIZE,
+	.bankwidth =	UFLASH_BUSWIDTH,
+};
+
+int uflash_devinit(struct platform_device *op, struct device_node *dp)
+{
+	struct uflash_dev *up;
+
+	if (op->resource[1].flags) {
+		/* Non-CFI userflash device-- once I find one we
+		 * can work on supporting it.
+		 */
+		printk(KERN_ERR PFX "Unsupported device at %s, 0x%llx\n",
+		       dp->full_name, (unsigned long long)op->resource[0].start);
+
+		return -ENODEV;
+	}
+
+	up = kzalloc(sizeof(struct uflash_dev), GFP_KERNEL);
+	if (!up) {
+		printk(KERN_ERR PFX "Cannot allocate struct uflash_dev\n");
+		return -ENOMEM;
+	}
+
+	/* copy defaults and tweak parameters */
+	memcpy(&up->map, &uflash_map_templ, sizeof(uflash_map_templ));
+
+	up->map.size = resource_size(&op->resource[0]);
+
+	up->name = of_get_property(dp, "model", NULL);
+	if (up->name && 0 < strlen(up->name))
+		up->map.name = up->name;
+
+	up->map.phys = op->resource[0].start;
+
+	up->map.virt = of_ioremap(&op->resource[0], 0, up->map.size,
+				  DRIVER_NAME);
+	if (!up->map.virt) {
+		printk(KERN_ERR PFX "Failed to map device.\n");
+		kfree(up);
+
+		return -EINVAL;
+	}
+
+	simple_map_init(&up->map);
+
+	/* MTD registration */
+	up->mtd = do_map_probe("cfi_probe", &up->map);
+	if (!up->mtd) {
+		of_iounmap(&op->resource[0], up->map.virt, up->map.size);
+		kfree(up);
+
+		return -ENXIO;
+	}
+
+	up->mtd->owner = THIS_MODULE;
+
+	mtd_device_register(up->mtd, NULL, 0);
+
+	dev_set_drvdata(&op->dev, up);
+
+	return 0;
+}
+
+static int uflash_probe(struct platform_device *op)
+{
+	struct device_node *dp = op->dev.of_node;
+
+	/* Flashprom must have the "user" property in order to
+	 * be used by this driver.
+	 */
+	if (!of_find_property(dp, "user", NULL))
+		return -ENODEV;
+
+	return uflash_devinit(op, dp);
+}
+
+static int uflash_remove(struct platform_device *op)
+{
+	struct uflash_dev *up = dev_get_drvdata(&op->dev);
+
+	if (up->mtd) {
+		mtd_device_unregister(up->mtd);
+		map_destroy(up->mtd);
+	}
+	if (up->map.virt) {
+		of_iounmap(&op->resource[0], up->map.virt, up->map.size);
+		up->map.virt = NULL;
+	}
+
+	kfree(up);
+
+	return 0;
+}
+
+static const struct of_device_id uflash_match[] = {
+	{
+		.name = UFLASH_OBPNAME,
+	},
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, uflash_match);
+
+static struct platform_driver uflash_driver = {
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table = uflash_match,
+	},
+	.probe		= uflash_probe,
+	.remove		= uflash_remove,
+};
+
+module_platform_driver(uflash_driver);
diff --git a/drivers/mtd/maps/ts5500_flash.c b/drivers/mtd/maps/ts5500_flash.c
new file mode 100644
index 000000000..9969fedb1
--- /dev/null
+++ b/drivers/mtd/maps/ts5500_flash.c
@@ -0,0 +1,121 @@
+/*
+ * ts5500_flash.c -- MTD map driver for Technology Systems TS-5500 board
+ *
+ * Copyright (C) 2004 Sean Young <sean@mess.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA
+ *
+ * Note:
+ * - In order for detection to work, jumper 3 must be set.
+ * - Drive A and B use the resident flash disk (RFD) flash translation layer.
+ * - If you have created your own jffs file system and the bios overwrites
+ *   it during boot, try disabling Drive A: and B: in the boot order.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/types.h>
+
+
+#define WINDOW_ADDR	0x09400000
+#define WINDOW_SIZE	0x00200000
+
+static struct map_info ts5500_map = {
+	.name = "TS-5500 Flash",
+	.size = WINDOW_SIZE,
+	.bankwidth = 1,
+	.phys = WINDOW_ADDR
+};
+
+static struct mtd_partition ts5500_partitions[] = {
+	{
+		.name = "Drive A",
+		.offset = 0,
+		.size = 0x0e0000
+	},
+	{
+		.name = "BIOS",
+		.offset = 0x0e0000,
+		.size = 0x020000,
+	},
+	{
+		.name = "Drive B",
+		.offset = 0x100000,
+		.size = 0x100000
+	}
+};
+
+#define NUM_PARTITIONS ARRAY_SIZE(ts5500_partitions)
+
+static struct mtd_info *mymtd;
+
+static int __init init_ts5500_map(void)
+{
+	int rc = 0;
+
+	ts5500_map.virt = ioremap_nocache(ts5500_map.phys, ts5500_map.size);
+
+	if (!ts5500_map.virt) {
+		printk(KERN_ERR "Failed to ioremap_nocache\n");
+		rc = -EIO;
+		goto err2;
+	}
+
+	simple_map_init(&ts5500_map);
+
+	mymtd = do_map_probe("jedec_probe", &ts5500_map);
+	if (!mymtd)
+		mymtd = do_map_probe("map_rom", &ts5500_map);
+
+	if (!mymtd) {
+		rc = -ENXIO;
+		goto err1;
+	}
+
+	mymtd->owner = THIS_MODULE;
+	mtd_device_register(mymtd, ts5500_partitions, NUM_PARTITIONS);
+
+	return 0;
+
+err1:
+	iounmap(ts5500_map.virt);
+err2:
+	return rc;
+}
+
+static void __exit cleanup_ts5500_map(void)
+{
+	if (mymtd) {
+		mtd_device_unregister(mymtd);
+		map_destroy(mymtd);
+	}
+
+	if (ts5500_map.virt) {
+		iounmap(ts5500_map.virt);
+		ts5500_map.virt = NULL;
+	}
+}
+
+module_init(init_ts5500_map);
+module_exit(cleanup_ts5500_map);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Sean Young <sean@mess.org>");
+MODULE_DESCRIPTION("MTD map driver for Technology Systems TS-5500 board");
+
diff --git a/drivers/mtd/maps/tsunami_flash.c b/drivers/mtd/maps/tsunami_flash.c
new file mode 100644
index 000000000..da2cdb5fd
--- /dev/null
+++ b/drivers/mtd/maps/tsunami_flash.c
@@ -0,0 +1,108 @@
+/*
+ * tsunami_flash.c
+ *
+ * flash chip on alpha ds10...
+ */
+#include <asm/io.h>
+#include <asm/core_tsunami.h>
+#include <linux/init.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/mtd.h>
+
+#define FLASH_ENABLE_PORT 0x00C00001
+#define FLASH_ENABLE_BYTE 0x01
+#define FLASH_DISABLE_BYTE 0x00
+
+#define MAX_TIG_FLASH_SIZE (12*1024*1024)
+static inline map_word tsunami_flash_read8(struct map_info *map, unsigned long offset)
+{
+	map_word val;
+	val.x[0] = tsunami_tig_readb(offset);
+	return val;
+}
+
+static void tsunami_flash_write8(struct map_info *map, map_word value, unsigned long offset)
+{
+	tsunami_tig_writeb(value.x[0], offset);
+}
+
+static void tsunami_flash_copy_from(
+	struct map_info *map, void *addr, unsigned long offset, ssize_t len)
+{
+	unsigned char *dest;
+	dest = addr;
+	while(len && (offset < MAX_TIG_FLASH_SIZE)) {
+		*dest = tsunami_tig_readb(offset);
+		offset++;
+		dest++;
+		len--;
+	}
+}
+
+static void tsunami_flash_copy_to(
+	struct map_info *map, unsigned long offset,
+	const void *addr, ssize_t len)
+{
+	const unsigned char *src;
+	src = addr;
+	while(len && (offset < MAX_TIG_FLASH_SIZE)) {
+		tsunami_tig_writeb(*src, offset);
+		offset++;
+		src++;
+		len--;
+	}
+}
+
+/*
+ * Deliberately don't provide operations wider than 8 bits.  I don't
+ * have then and it scares me to think how you could mess up if
+ * you tried to use them.   Buswidth is correctly so I'm safe.
+ */
+static struct map_info tsunami_flash_map = {
+	.name = "flash chip on the Tsunami TIG bus",
+	.size = MAX_TIG_FLASH_SIZE,
+	.phys = NO_XIP,
+	.bankwidth = 1,
+	.read = tsunami_flash_read8,
+	.copy_from = tsunami_flash_copy_from,
+	.write = tsunami_flash_write8,
+	.copy_to = tsunami_flash_copy_to,
+};
+
+static struct mtd_info *tsunami_flash_mtd;
+
+static void __exit  cleanup_tsunami_flash(void)
+{
+	struct mtd_info *mtd;
+	mtd = tsunami_flash_mtd;
+	if (mtd) {
+		mtd_device_unregister(mtd);
+		map_destroy(mtd);
+	}
+	tsunami_flash_mtd = 0;
+}
+
+static const char * const rom_probe_types[] = {
+	"cfi_probe", "jedec_probe", "map_rom", NULL };
+
+static int __init init_tsunami_flash(void)
+{
+	const char * const *type;
+
+	tsunami_tig_writeb(FLASH_ENABLE_BYTE, FLASH_ENABLE_PORT);
+
+	tsunami_flash_mtd = 0;
+	type = rom_probe_types;
+	for(; !tsunami_flash_mtd && *type; type++) {
+		tsunami_flash_mtd = do_map_probe(*type, &tsunami_flash_map);
+	}
+	if (tsunami_flash_mtd) {
+		tsunami_flash_mtd->owner = THIS_MODULE;
+		mtd_device_register(tsunami_flash_mtd, NULL, 0);
+		return 0;
+	}
+	return -ENXIO;
+}
+
+module_init(init_tsunami_flash);
+module_exit(cleanup_tsunami_flash);
diff --git a/drivers/mtd/maps/uclinux.c b/drivers/mtd/maps/uclinux.c
new file mode 100644
index 000000000..c1af83db5
--- /dev/null
+++ b/drivers/mtd/maps/uclinux.c
@@ -0,0 +1,143 @@
+/****************************************************************************/
+
+/*
+ *	uclinux.c -- generic memory mapped MTD driver for uclinux
+ *
+ *	(C) Copyright 2002, Greg Ungerer (gerg@snapgear.com)
+ */
+
+/****************************************************************************/
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/fs.h>
+#include <linux/mm.h>
+#include <linux/major.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/partitions.h>
+#include <asm/io.h>
+#include <asm/sections.h>
+
+/****************************************************************************/
+
+#ifdef CONFIG_MTD_ROM
+#define MAP_NAME "rom"
+#else
+#define MAP_NAME "ram"
+#endif
+
+/*
+ * Blackfin uses uclinux_ram_map during startup, so it must not be static.
+ * Provide a dummy declaration to make sparse happy.
+ */
+extern struct map_info uclinux_ram_map;
+
+struct map_info uclinux_ram_map = {
+	.name = MAP_NAME,
+	.size = 0,
+};
+
+static unsigned long physaddr = -1;
+module_param(physaddr, ulong, S_IRUGO);
+
+static struct mtd_info *uclinux_ram_mtdinfo;
+
+/****************************************************************************/
+
+static struct mtd_partition uclinux_romfs[] = {
+	{ .name = "ROMfs" }
+};
+
+#define	NUM_PARTITIONS	ARRAY_SIZE(uclinux_romfs)
+
+/****************************************************************************/
+
+static int uclinux_point(struct mtd_info *mtd, loff_t from, size_t len,
+	size_t *retlen, void **virt, resource_size_t *phys)
+{
+	struct map_info *map = mtd->priv;
+	*virt = map->virt + from;
+	if (phys)
+		*phys = map->phys + from;
+	*retlen = len;
+	return(0);
+}
+
+/****************************************************************************/
+
+static int __init uclinux_mtd_init(void)
+{
+	struct mtd_info *mtd;
+	struct map_info *mapp;
+
+	mapp = &uclinux_ram_map;
+
+	if (physaddr == -1)
+		mapp->phys = (resource_size_t)__bss_stop;
+	else
+		mapp->phys = physaddr;
+
+	if (!mapp->size)
+		mapp->size = PAGE_ALIGN(ntohl(*((unsigned long *)(mapp->phys + 8))));
+	mapp->bankwidth = 4;
+
+	printk("uclinux[mtd]: probe address=0x%x size=0x%x\n",
+	       	(int) mapp->phys, (int) mapp->size);
+
+	/*
+	 * The filesystem is guaranteed to be in direct mapped memory. It is
+	 * directly following the kernels own bss region. Following the same
+	 * mechanism used by architectures setting up traditional initrds we
+	 * use phys_to_virt to get the virtual address of its start.
+	 */
+	mapp->virt = phys_to_virt(mapp->phys);
+
+	if (mapp->virt == 0) {
+		printk("uclinux[mtd]: no virtual mapping?\n");
+		return(-EIO);
+	}
+
+	simple_map_init(mapp);
+
+	mtd = do_map_probe("map_" MAP_NAME, mapp);
+	if (!mtd) {
+		printk("uclinux[mtd]: failed to find a mapping?\n");
+		return(-ENXIO);
+	}
+
+	mtd->owner = THIS_MODULE;
+	mtd->_point = uclinux_point;
+	mtd->priv = mapp;
+
+	uclinux_ram_mtdinfo = mtd;
+	mtd_device_register(mtd, uclinux_romfs, NUM_PARTITIONS);
+
+	return(0);
+}
+
+/****************************************************************************/
+
+static void __exit uclinux_mtd_cleanup(void)
+{
+	if (uclinux_ram_mtdinfo) {
+		mtd_device_unregister(uclinux_ram_mtdinfo);
+		map_destroy(uclinux_ram_mtdinfo);
+		uclinux_ram_mtdinfo = NULL;
+	}
+	if (uclinux_ram_map.virt)
+		uclinux_ram_map.virt = 0;
+}
+
+/****************************************************************************/
+
+module_init(uclinux_mtd_init);
+module_exit(uclinux_mtd_cleanup);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Greg Ungerer <gerg@snapgear.com>");
+MODULE_DESCRIPTION("Generic MTD for uClinux");
+
+/****************************************************************************/
diff --git a/drivers/mtd/maps/vmu-flash.c b/drivers/mtd/maps/vmu-flash.c
new file mode 100644
index 000000000..6b223cfe9
--- /dev/null
+++ b/drivers/mtd/maps/vmu-flash.c
@@ -0,0 +1,824 @@
+/* vmu-flash.c
+ * Driver for SEGA Dreamcast Visual Memory Unit
+ *
+ * Copyright (c) Adrian McMenamin 2002 - 2009
+ * Copyright (c) Paul Mundt 2001
+ *
+ * Licensed under version 2 of the
+ * GNU General Public Licence
+ */
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/sched.h>
+#include <linux/delay.h>
+#include <linux/maple.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+
+struct vmu_cache {
+	unsigned char *buffer;		/* Cache */
+	unsigned int block;		/* Which block was cached */
+	unsigned long jiffies_atc;	/* When was it cached? */
+	int valid;
+};
+
+struct mdev_part {
+	struct maple_device *mdev;
+	int partition;
+};
+
+struct vmupart {
+	u16 user_blocks;
+	u16 root_block;
+	u16 numblocks;
+	char *name;
+	struct vmu_cache *pcache;
+};
+
+struct memcard {
+	u16 tempA;
+	u16 tempB;
+	u32 partitions;
+	u32 blocklen;
+	u32 writecnt;
+	u32 readcnt;
+	u32 removeable;
+	int partition;
+	int read;
+	unsigned char *blockread;
+	struct vmupart *parts;
+	struct mtd_info *mtd;
+};
+
+struct vmu_block {
+	unsigned int num; /* block number */
+	unsigned int ofs; /* block offset */
+};
+
+static struct vmu_block *ofs_to_block(unsigned long src_ofs,
+	struct mtd_info *mtd, int partition)
+{
+	struct vmu_block *vblock;
+	struct maple_device *mdev;
+	struct memcard *card;
+	struct mdev_part *mpart;
+	int num;
+
+	mpart = mtd->priv;
+	mdev = mpart->mdev;
+	card = maple_get_drvdata(mdev);
+
+	if (src_ofs >= card->parts[partition].numblocks * card->blocklen)
+		goto failed;
+
+	num = src_ofs / card->blocklen;
+	if (num > card->parts[partition].numblocks)
+		goto failed;
+
+	vblock = kmalloc(sizeof(struct vmu_block), GFP_KERNEL);
+	if (!vblock)
+		goto failed;
+
+	vblock->num = num;
+	vblock->ofs = src_ofs % card->blocklen;
+	return vblock;
+
+failed:
+	return NULL;
+}
+
+/* Maple bus callback function for reads */
+static void vmu_blockread(struct mapleq *mq)
+{
+	struct maple_device *mdev;
+	struct memcard *card;
+
+	mdev = mq->dev;
+	card = maple_get_drvdata(mdev);
+	/* copy the read in data */
+
+	if (unlikely(!card->blockread))
+		return;
+
+	memcpy(card->blockread, mq->recvbuf->buf + 12,
+		card->blocklen/card->readcnt);
+
+}
+
+/* Interface with maple bus to read blocks
+ * caching the results so that other parts
+ * of the driver can access block reads */
+static int maple_vmu_read_block(unsigned int num, unsigned char *buf,
+	struct mtd_info *mtd)
+{
+	struct memcard *card;
+	struct mdev_part *mpart;
+	struct maple_device *mdev;
+	int partition, error = 0, x, wait;
+	unsigned char *blockread = NULL;
+	struct vmu_cache *pcache;
+	__be32 sendbuf;
+
+	mpart = mtd->priv;
+	mdev = mpart->mdev;
+	partition = mpart->partition;
+	card = maple_get_drvdata(mdev);
+	pcache = card->parts[partition].pcache;
+	pcache->valid = 0;
+
+	/* prepare the cache for this block */
+	if (!pcache->buffer) {
+		pcache->buffer = kmalloc(card->blocklen, GFP_KERNEL);
+		if (!pcache->buffer) {
+			dev_err(&mdev->dev, "VMU at (%d, %d) - read fails due"
+				" to lack of memory\n", mdev->port,
+				mdev->unit);
+			error = -ENOMEM;
+			goto outB;
+		}
+	}
+
+	/*
+	* Reads may be phased - again the hardware spec
+	* supports this - though may not be any devices in
+	* the wild that implement it, but we will here
+	*/
+	for (x = 0; x < card->readcnt; x++) {
+		sendbuf = cpu_to_be32(partition << 24 | x << 16 | num);
+
+		if (atomic_read(&mdev->busy) == 1) {
+			wait_event_interruptible_timeout(mdev->maple_wait,
+				atomic_read(&mdev->busy) == 0, HZ);
+			if (atomic_read(&mdev->busy) == 1) {
+				dev_notice(&mdev->dev, "VMU at (%d, %d)"
+					" is busy\n", mdev->port, mdev->unit);
+				error = -EAGAIN;
+				goto outB;
+			}
+		}
+
+		atomic_set(&mdev->busy, 1);
+		blockread = kmalloc(card->blocklen/card->readcnt, GFP_KERNEL);
+		if (!blockread) {
+			error = -ENOMEM;
+			atomic_set(&mdev->busy, 0);
+			goto outB;
+		}
+		card->blockread = blockread;
+
+		maple_getcond_callback(mdev, vmu_blockread, 0,
+			MAPLE_FUNC_MEMCARD);
+		error = maple_add_packet(mdev, MAPLE_FUNC_MEMCARD,
+				MAPLE_COMMAND_BREAD, 2, &sendbuf);
+		/* Very long timeouts seem to be needed when box is stressed */
+		wait = wait_event_interruptible_timeout(mdev->maple_wait,
+			(atomic_read(&mdev->busy) == 0 ||
+			atomic_read(&mdev->busy) == 2), HZ * 3);
+		/*
+		* MTD layer does not handle hotplugging well
+		* so have to return errors when VMU is unplugged
+		* in the middle of a read (busy == 2)
+		*/
+		if (error || atomic_read(&mdev->busy) == 2) {
+			if (atomic_read(&mdev->busy) == 2)
+				error = -ENXIO;
+			atomic_set(&mdev->busy, 0);
+			card->blockread = NULL;
+			goto outA;
+		}
+		if (wait == 0 || wait == -ERESTARTSYS) {
+			card->blockread = NULL;
+			atomic_set(&mdev->busy, 0);
+			error = -EIO;
+			list_del_init(&(mdev->mq->list));
+			kfree(mdev->mq->sendbuf);
+			mdev->mq->sendbuf = NULL;
+			if (wait == -ERESTARTSYS) {
+				dev_warn(&mdev->dev, "VMU read on (%d, %d)"
+					" interrupted on block 0x%X\n",
+					mdev->port, mdev->unit, num);
+			} else
+				dev_notice(&mdev->dev, "VMU read on (%d, %d)"
+					" timed out on block 0x%X\n",
+					mdev->port, mdev->unit, num);
+			goto outA;
+		}
+
+		memcpy(buf + (card->blocklen/card->readcnt) * x, blockread,
+			card->blocklen/card->readcnt);
+
+		memcpy(pcache->buffer + (card->blocklen/card->readcnt) * x,
+			card->blockread, card->blocklen/card->readcnt);
+		card->blockread = NULL;
+		pcache->block = num;
+		pcache->jiffies_atc = jiffies;
+		pcache->valid = 1;
+		kfree(blockread);
+	}
+
+	return error;
+
+outA:
+	kfree(blockread);
+outB:
+	return error;
+}
+
+/* communicate with maple bus for phased writing */
+static int maple_vmu_write_block(unsigned int num, const unsigned char *buf,
+	struct mtd_info *mtd)
+{
+	struct memcard *card;
+	struct mdev_part *mpart;
+	struct maple_device *mdev;
+	int partition, error, locking, x, phaselen, wait;
+	__be32 *sendbuf;
+
+	mpart = mtd->priv;
+	mdev = mpart->mdev;
+	partition = mpart->partition;
+	card = maple_get_drvdata(mdev);
+
+	phaselen = card->blocklen/card->writecnt;
+
+	sendbuf = kmalloc(phaselen + 4, GFP_KERNEL);
+	if (!sendbuf) {
+		error = -ENOMEM;
+		goto fail_nosendbuf;
+	}
+	for (x = 0; x < card->writecnt; x++) {
+		sendbuf[0] = cpu_to_be32(partition << 24 | x << 16 | num);
+		memcpy(&sendbuf[1], buf + phaselen * x, phaselen);
+		/* wait until the device is not busy doing something else
+		* or 1 second - which ever is longer */
+		if (atomic_read(&mdev->busy) == 1) {
+			wait_event_interruptible_timeout(mdev->maple_wait,
+				atomic_read(&mdev->busy) == 0, HZ);
+			if (atomic_read(&mdev->busy) == 1) {
+				error = -EBUSY;
+				dev_notice(&mdev->dev, "VMU write at (%d, %d)"
+					"failed - device is busy\n",
+					mdev->port, mdev->unit);
+				goto fail_nolock;
+			}
+		}
+		atomic_set(&mdev->busy, 1);
+
+		locking = maple_add_packet(mdev, MAPLE_FUNC_MEMCARD,
+			MAPLE_COMMAND_BWRITE, phaselen / 4 + 2, sendbuf);
+		wait = wait_event_interruptible_timeout(mdev->maple_wait,
+			atomic_read(&mdev->busy) == 0, HZ/10);
+		if (locking) {
+			error = -EIO;
+			atomic_set(&mdev->busy, 0);
+			goto fail_nolock;
+		}
+		if (atomic_read(&mdev->busy) == 2) {
+			atomic_set(&mdev->busy, 0);
+		} else if (wait == 0 || wait == -ERESTARTSYS) {
+			error = -EIO;
+			dev_warn(&mdev->dev, "Write at (%d, %d) of block"
+				" 0x%X at phase %d failed: could not"
+				" communicate with VMU", mdev->port,
+				mdev->unit, num, x);
+			atomic_set(&mdev->busy, 0);
+			kfree(mdev->mq->sendbuf);
+			mdev->mq->sendbuf = NULL;
+			list_del_init(&(mdev->mq->list));
+			goto fail_nolock;
+		}
+	}
+	kfree(sendbuf);
+
+	return card->blocklen;
+
+fail_nolock:
+	kfree(sendbuf);
+fail_nosendbuf:
+	dev_err(&mdev->dev, "VMU (%d, %d): write failed\n", mdev->port,
+		mdev->unit);
+	return error;
+}
+
+/* mtd function to simulate reading byte by byte */
+static unsigned char vmu_flash_read_char(unsigned long ofs, int *retval,
+	struct mtd_info *mtd)
+{
+	struct vmu_block *vblock;
+	struct memcard *card;
+	struct mdev_part *mpart;
+	struct maple_device *mdev;
+	unsigned char *buf, ret;
+	int partition, error;
+
+	mpart = mtd->priv;
+	mdev = mpart->mdev;
+	partition = mpart->partition;
+	card = maple_get_drvdata(mdev);
+	*retval =  0;
+
+	buf = kmalloc(card->blocklen, GFP_KERNEL);
+	if (!buf) {
+		*retval = 1;
+		ret = -ENOMEM;
+		goto finish;
+	}
+
+	vblock = ofs_to_block(ofs, mtd, partition);
+	if (!vblock) {
+		*retval = 3;
+		ret = -ENOMEM;
+		goto out_buf;
+	}
+
+	error = maple_vmu_read_block(vblock->num, buf, mtd);
+	if (error) {
+		ret = error;
+		*retval = 2;
+		goto out_vblock;
+	}
+
+	ret = buf[vblock->ofs];
+
+out_vblock:
+	kfree(vblock);
+out_buf:
+	kfree(buf);
+finish:
+	return ret;
+}
+
+/* mtd higher order function to read flash */
+static int vmu_flash_read(struct mtd_info *mtd, loff_t from, size_t len,
+	size_t *retlen,  u_char *buf)
+{
+	struct maple_device *mdev;
+	struct memcard *card;
+	struct mdev_part *mpart;
+	struct vmu_cache *pcache;
+	struct vmu_block *vblock;
+	int index = 0, retval, partition, leftover, numblocks;
+	unsigned char cx;
+
+	mpart = mtd->priv;
+	mdev = mpart->mdev;
+	partition = mpart->partition;
+	card = maple_get_drvdata(mdev);
+
+	numblocks = card->parts[partition].numblocks;
+	if (from + len > numblocks * card->blocklen)
+		len = numblocks * card->blocklen - from;
+	if (len == 0)
+		return -EIO;
+	/* Have we cached this bit already? */
+	pcache = card->parts[partition].pcache;
+	do {
+		vblock =  ofs_to_block(from + index, mtd, partition);
+		if (!vblock)
+			return -ENOMEM;
+		/* Have we cached this and is the cache valid and timely? */
+		if (pcache->valid &&
+			time_before(jiffies, pcache->jiffies_atc + HZ) &&
+			(pcache->block == vblock->num)) {
+			/* we have cached it, so do necessary copying */
+			leftover = card->blocklen - vblock->ofs;
+			if (vblock->ofs + len - index < card->blocklen) {
+				/* only a bit of this block to copy */
+				memcpy(buf + index,
+					pcache->buffer + vblock->ofs,
+					len - index);
+				index = len;
+			} else {
+				/* otherwise copy remainder of whole block */
+				memcpy(buf + index, pcache->buffer +
+					vblock->ofs, leftover);
+				index += leftover;
+			}
+		} else {
+			/*
+			* Not cached so read one byte -
+			* but cache the rest of the block
+			*/
+			cx = vmu_flash_read_char(from + index, &retval, mtd);
+			if (retval) {
+				*retlen = index;
+				kfree(vblock);
+				return cx;
+			}
+			memset(buf + index, cx, 1);
+			index++;
+		}
+		kfree(vblock);
+	} while (len > index);
+	*retlen = index;
+
+	return 0;
+}
+
+static int vmu_flash_write(struct mtd_info *mtd, loff_t to, size_t len,
+	size_t *retlen, const u_char *buf)
+{
+	struct maple_device *mdev;
+	struct memcard *card;
+	struct mdev_part *mpart;
+	int index = 0, partition, error = 0, numblocks;
+	struct vmu_cache *pcache;
+	struct vmu_block *vblock;
+	unsigned char *buffer;
+
+	mpart = mtd->priv;
+	mdev = mpart->mdev;
+	partition = mpart->partition;
+	card = maple_get_drvdata(mdev);
+
+	numblocks = card->parts[partition].numblocks;
+	if (to + len > numblocks * card->blocklen)
+		len = numblocks * card->blocklen - to;
+	if (len == 0) {
+		error = -EIO;
+		goto failed;
+	}
+
+	vblock = ofs_to_block(to, mtd, partition);
+	if (!vblock) {
+		error = -ENOMEM;
+		goto failed;
+	}
+
+	buffer = kmalloc(card->blocklen, GFP_KERNEL);
+	if (!buffer) {
+		error = -ENOMEM;
+		goto fail_buffer;
+	}
+
+	do {
+		/* Read in the block we are to write to */
+		error = maple_vmu_read_block(vblock->num, buffer, mtd);
+		if (error)
+			goto fail_io;
+
+		do {
+			buffer[vblock->ofs] = buf[index];
+			vblock->ofs++;
+			index++;
+			if (index >= len)
+				break;
+		} while (vblock->ofs < card->blocklen);
+
+		/* write out new buffer */
+		error = maple_vmu_write_block(vblock->num, buffer, mtd);
+		/* invalidate the cache */
+		pcache = card->parts[partition].pcache;
+		pcache->valid = 0;
+
+		if (error != card->blocklen)
+			goto fail_io;
+
+		vblock->num++;
+		vblock->ofs = 0;
+	} while (len > index);
+
+	kfree(buffer);
+	*retlen = index;
+	kfree(vblock);
+	return 0;
+
+fail_io:
+	kfree(buffer);
+fail_buffer:
+	kfree(vblock);
+failed:
+	dev_err(&mdev->dev, "VMU write failing with error %d\n", error);
+	return error;
+}
+
+static void vmu_flash_sync(struct mtd_info *mtd)
+{
+	/* Do nothing here */
+}
+
+/* Maple bus callback function to recursively query hardware details */
+static void vmu_queryblocks(struct mapleq *mq)
+{
+	struct maple_device *mdev;
+	unsigned short *res;
+	struct memcard *card;
+	__be32 partnum;
+	struct vmu_cache *pcache;
+	struct mdev_part *mpart;
+	struct mtd_info *mtd_cur;
+	struct vmupart *part_cur;
+	int error;
+
+	mdev = mq->dev;
+	card = maple_get_drvdata(mdev);
+	res = (unsigned short *) (mq->recvbuf->buf);
+	card->tempA = res[12];
+	card->tempB = res[6];
+
+	dev_info(&mdev->dev, "VMU device at partition %d has %d user "
+		"blocks with a root block at %d\n", card->partition,
+		card->tempA, card->tempB);
+
+	part_cur = &card->parts[card->partition];
+	part_cur->user_blocks = card->tempA;
+	part_cur->root_block = card->tempB;
+	part_cur->numblocks = card->tempB + 1;
+	part_cur->name = kmalloc(12, GFP_KERNEL);
+	if (!part_cur->name)
+		goto fail_name;
+
+	sprintf(part_cur->name, "vmu%d.%d.%d",
+		mdev->port, mdev->unit, card->partition);
+	mtd_cur = &card->mtd[card->partition];
+	mtd_cur->name = part_cur->name;
+	mtd_cur->type = 8;
+	mtd_cur->flags = MTD_WRITEABLE|MTD_NO_ERASE;
+	mtd_cur->size = part_cur->numblocks * card->blocklen;
+	mtd_cur->erasesize = card->blocklen;
+	mtd_cur->_write = vmu_flash_write;
+	mtd_cur->_read = vmu_flash_read;
+	mtd_cur->_sync = vmu_flash_sync;
+	mtd_cur->writesize = card->blocklen;
+
+	mpart = kmalloc(sizeof(struct mdev_part), GFP_KERNEL);
+	if (!mpart)
+		goto fail_mpart;
+
+	mpart->mdev = mdev;
+	mpart->partition = card->partition;
+	mtd_cur->priv = mpart;
+	mtd_cur->owner = THIS_MODULE;
+
+	pcache = kzalloc(sizeof(struct vmu_cache), GFP_KERNEL);
+	if (!pcache)
+		goto fail_cache_create;
+	part_cur->pcache = pcache;
+
+	error = mtd_device_register(mtd_cur, NULL, 0);
+	if (error)
+		goto fail_mtd_register;
+
+	maple_getcond_callback(mdev, NULL, 0,
+		MAPLE_FUNC_MEMCARD);
+
+	/*
+	* Set up a recursive call to the (probably theoretical)
+	* second or more partition
+	*/
+	if (++card->partition < card->partitions) {
+		partnum = cpu_to_be32(card->partition << 24);
+		maple_getcond_callback(mdev, vmu_queryblocks, 0,
+			MAPLE_FUNC_MEMCARD);
+		maple_add_packet(mdev, MAPLE_FUNC_MEMCARD,
+			MAPLE_COMMAND_GETMINFO, 2, &partnum);
+	}
+	return;
+
+fail_mtd_register:
+	dev_err(&mdev->dev, "Could not register maple device at (%d, %d)"
+		"error is 0x%X\n", mdev->port, mdev->unit, error);
+	for (error = 0; error <= card->partition; error++) {
+		kfree(((card->parts)[error]).pcache);
+		((card->parts)[error]).pcache = NULL;
+	}
+fail_cache_create:
+fail_mpart:
+	for (error = 0; error <= card->partition; error++) {
+		kfree(((card->mtd)[error]).priv);
+		((card->mtd)[error]).priv = NULL;
+	}
+	maple_getcond_callback(mdev, NULL, 0,
+		MAPLE_FUNC_MEMCARD);
+	kfree(part_cur->name);
+fail_name:
+	return;
+}
+
+/* Handles very basic info about the flash, queries for details */
+static int vmu_connect(struct maple_device *mdev)
+{
+	unsigned long test_flash_data, basic_flash_data;
+	int c, error;
+	struct memcard *card;
+	u32 partnum = 0;
+
+	test_flash_data = be32_to_cpu(mdev->devinfo.function);
+	/* Need to count how many bits are set - to find out which
+	 * function_data element has details of the memory card
+	 */
+	c = hweight_long(test_flash_data);
+
+	basic_flash_data = be32_to_cpu(mdev->devinfo.function_data[c - 1]);
+
+	card = kmalloc(sizeof(struct memcard), GFP_KERNEL);
+	if (!card) {
+		error = -ENOMEM;
+		goto fail_nomem;
+	}
+
+	card->partitions = (basic_flash_data >> 24 & 0xFF) + 1;
+	card->blocklen = ((basic_flash_data >> 16 & 0xFF) + 1) << 5;
+	card->writecnt = basic_flash_data >> 12 & 0xF;
+	card->readcnt = basic_flash_data >> 8 & 0xF;
+	card->removeable = basic_flash_data >> 7 & 1;
+
+	card->partition = 0;
+
+	/*
+	* Not sure there are actually any multi-partition devices in the
+	* real world, but the hardware supports them, so, so will we
+	*/
+	card->parts = kmalloc(sizeof(struct vmupart) * card->partitions,
+		GFP_KERNEL);
+	if (!card->parts) {
+		error = -ENOMEM;
+		goto fail_partitions;
+	}
+
+	card->mtd = kmalloc(sizeof(struct mtd_info) * card->partitions,
+		GFP_KERNEL);
+	if (!card->mtd) {
+		error = -ENOMEM;
+		goto fail_mtd_info;
+	}
+
+	maple_set_drvdata(mdev, card);
+
+	/*
+	* We want to trap meminfo not get cond
+	* so set interval to zero, but rely on maple bus
+	* driver to pass back the results of the meminfo
+	*/
+	maple_getcond_callback(mdev, vmu_queryblocks, 0,
+		MAPLE_FUNC_MEMCARD);
+
+	/* Make sure we are clear to go */
+	if (atomic_read(&mdev->busy) == 1) {
+		wait_event_interruptible_timeout(mdev->maple_wait,
+			atomic_read(&mdev->busy) == 0, HZ);
+		if (atomic_read(&mdev->busy) == 1) {
+			dev_notice(&mdev->dev, "VMU at (%d, %d) is busy\n",
+				mdev->port, mdev->unit);
+			error = -EAGAIN;
+			goto fail_device_busy;
+		}
+	}
+
+	atomic_set(&mdev->busy, 1);
+
+	/*
+	* Set up the minfo call: vmu_queryblocks will handle
+	* the information passed back
+	*/
+	error = maple_add_packet(mdev, MAPLE_FUNC_MEMCARD,
+		MAPLE_COMMAND_GETMINFO, 2, &partnum);
+	if (error) {
+		dev_err(&mdev->dev, "Could not lock VMU at (%d, %d)"
+			" error is 0x%X\n", mdev->port, mdev->unit, error);
+		goto fail_mtd_info;
+	}
+	return 0;
+
+fail_device_busy:
+	kfree(card->mtd);
+fail_mtd_info:
+	kfree(card->parts);
+fail_partitions:
+	kfree(card);
+fail_nomem:
+	return error;
+}
+
+static void vmu_disconnect(struct maple_device *mdev)
+{
+	struct memcard *card;
+	struct mdev_part *mpart;
+	int x;
+
+	mdev->callback = NULL;
+	card = maple_get_drvdata(mdev);
+	for (x = 0; x < card->partitions; x++) {
+		mpart = ((card->mtd)[x]).priv;
+		mpart->mdev = NULL;
+		mtd_device_unregister(&((card->mtd)[x]));
+		kfree(((card->parts)[x]).name);
+	}
+	kfree(card->parts);
+	kfree(card->mtd);
+	kfree(card);
+}
+
+/* Callback to handle eccentricities of both mtd subsystem
+ * and general flakyness of Dreamcast VMUs
+ */
+static int vmu_can_unload(struct maple_device *mdev)
+{
+	struct memcard *card;
+	int x;
+	struct mtd_info *mtd;
+
+	card = maple_get_drvdata(mdev);
+	for (x = 0; x < card->partitions; x++) {
+		mtd = &((card->mtd)[x]);
+		if (mtd->usecount > 0)
+			return 0;
+	}
+	return 1;
+}
+
+#define ERRSTR "VMU at (%d, %d) file error -"
+
+static void vmu_file_error(struct maple_device *mdev, void *recvbuf)
+{
+	enum maple_file_errors error = ((int *)recvbuf)[1];
+
+	switch (error) {
+
+	case MAPLE_FILEERR_INVALID_PARTITION:
+		dev_notice(&mdev->dev, ERRSTR " invalid partition number\n",
+			mdev->port, mdev->unit);
+		break;
+
+	case MAPLE_FILEERR_PHASE_ERROR:
+		dev_notice(&mdev->dev, ERRSTR " phase error\n",
+			mdev->port, mdev->unit);
+		break;
+
+	case MAPLE_FILEERR_INVALID_BLOCK:
+		dev_notice(&mdev->dev, ERRSTR " invalid block number\n",
+			mdev->port, mdev->unit);
+		break;
+
+	case MAPLE_FILEERR_WRITE_ERROR:
+		dev_notice(&mdev->dev, ERRSTR " write error\n",
+			mdev->port, mdev->unit);
+		break;
+
+	case MAPLE_FILEERR_INVALID_WRITE_LENGTH:
+		dev_notice(&mdev->dev, ERRSTR " invalid write length\n",
+			mdev->port, mdev->unit);
+		break;
+
+	case MAPLE_FILEERR_BAD_CRC:
+		dev_notice(&mdev->dev, ERRSTR " bad CRC\n",
+			mdev->port, mdev->unit);
+		break;
+
+	default:
+		dev_notice(&mdev->dev, ERRSTR " 0x%X\n",
+			mdev->port, mdev->unit, error);
+	}
+}
+
+
+static int probe_maple_vmu(struct device *dev)
+{
+	int error;
+	struct maple_device *mdev = to_maple_dev(dev);
+	struct maple_driver *mdrv = to_maple_driver(dev->driver);
+
+	mdev->can_unload = vmu_can_unload;
+	mdev->fileerr_handler = vmu_file_error;
+	mdev->driver = mdrv;
+
+	error = vmu_connect(mdev);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+static int remove_maple_vmu(struct device *dev)
+{
+	struct maple_device *mdev = to_maple_dev(dev);
+
+	vmu_disconnect(mdev);
+	return 0;
+}
+
+static struct maple_driver vmu_flash_driver = {
+	.function =	MAPLE_FUNC_MEMCARD,
+	.drv = {
+		.name =		"Dreamcast_visual_memory",
+		.probe =	probe_maple_vmu,
+		.remove =	remove_maple_vmu,
+	},
+};
+
+static int __init vmu_flash_map_init(void)
+{
+	return maple_driver_register(&vmu_flash_driver);
+}
+
+static void __exit vmu_flash_map_exit(void)
+{
+	maple_driver_unregister(&vmu_flash_driver);
+}
+
+module_init(vmu_flash_map_init);
+module_exit(vmu_flash_map_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Adrian McMenamin");
+MODULE_DESCRIPTION("Flash mapping for Sega Dreamcast visual memory");