Linux-libre 4.5-gnu

21 files changed, 649 insertions, 505 deletions

diff --git a/drivers/net/wireless/ti/Kconfig b/drivers/net/wireless/ti/Kconfig
index cbe1e7fef..92fbd6597 100644
--- a/drivers/net/wireless/ti/Kconfig
+++ b/drivers/net/wireless/ti/Kconfig
@@ -1,11 +1,15 @@
-menuconfig WL_TI
-	bool "TI Wireless LAN support"
+config WLAN_VENDOR_TI
+	bool "Texas Instrument devices"
+	default y
 	---help---
-	  This section contains support for all the wireless drivers
-	  for Texas Instruments WLAN chips, such as wl1251 and the wl12xx
-	  family.
+	  If you have a wireless card belonging to this class, say Y.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about  cards. If you say Y, you will be asked for
+	  your specific card in the following questions.
 
-if WL_TI
+if WLAN_VENDOR_TI
 source "drivers/net/wireless/ti/wl1251/Kconfig"
 source "drivers/net/wireless/ti/wl12xx/Kconfig"
 source "drivers/net/wireless/ti/wl18xx/Kconfig"
@@ -21,4 +25,4 @@ config WILINK_PLATFORM_DATA
 	Small platform data bit needed to pass data to the sdio modules.
 
 
-endif # WL_TI
+endif # WLAN_VENDOR_TI
diff --git a/drivers/net/wireless/ti/wl1251/Kconfig b/drivers/net/wireless/ti/wl1251/Kconfig
index 477a206c0..7142ccf3a 100644
--- a/drivers/net/wireless/ti/wl1251/Kconfig
+++ b/drivers/net/wireless/ti/wl1251/Kconfig
@@ -1,4 +1,4 @@
-menuconfig WL1251
+config WL1251
 	tristate "TI wl1251 driver support"
 	depends on MAC80211
 	select FW_LOADER
diff --git a/drivers/net/wireless/ti/wl12xx/conf.h b/drivers/net/wireless/ti/wl12xx/conf.h
index 75e29897a..a606ba9ef 100644
--- a/drivers/net/wireless/ti/wl12xx/conf.h
+++ b/drivers/net/wireless/ti/wl12xx/conf.h
@@ -47,4 +47,237 @@ struct wl12xx_priv_conf {
 	struct conf_memory_settings mem_wl127x;
 };
 
+enum wl12xx_sg_params {
+	/*
+	* Configure the min and max time BT gains the antenna
+	* in WLAN / BT master basic rate
+	*
+	* Range: 0 - 255 (ms)
+	*/
+	WL12XX_CONF_SG_ACL_BT_MASTER_MIN_BR = 0,
+	WL12XX_CONF_SG_ACL_BT_MASTER_MAX_BR,
+
+	/*
+	* Configure the min and max time BT gains the antenna
+	* in WLAN / BT slave basic rate
+	*
+	* Range: 0 - 255 (ms)
+	*/
+	WL12XX_CONF_SG_ACL_BT_SLAVE_MIN_BR,
+	WL12XX_CONF_SG_ACL_BT_SLAVE_MAX_BR,
+
+	/*
+	* Configure the min and max time BT gains the antenna
+	* in WLAN / BT master EDR
+	*
+	* Range: 0 - 255 (ms)
+	*/
+	WL12XX_CONF_SG_ACL_BT_MASTER_MIN_EDR,
+	WL12XX_CONF_SG_ACL_BT_MASTER_MAX_EDR,
+
+	/*
+	* Configure the min and max time BT gains the antenna
+	* in WLAN / BT slave EDR
+	*
+	* Range: 0 - 255 (ms)
+	*/
+	WL12XX_CONF_SG_ACL_BT_SLAVE_MIN_EDR,
+	WL12XX_CONF_SG_ACL_BT_SLAVE_MAX_EDR,
+
+	/*
+	* The maximum time WLAN can gain the antenna
+	* in WLAN PSM / BT master/slave BR
+	*
+	* Range: 0 - 255 (ms)
+	*/
+	WL12XX_CONF_SG_ACL_WLAN_PS_MASTER_BR,
+	WL12XX_CONF_SG_ACL_WLAN_PS_SLAVE_BR,
+
+	/*
+	* The maximum time WLAN can gain the antenna
+	* in WLAN PSM / BT master/slave EDR
+	*
+	* Range: 0 - 255 (ms)
+	*/
+	WL12XX_CONF_SG_ACL_WLAN_PS_MASTER_EDR,
+	WL12XX_CONF_SG_ACL_WLAN_PS_SLAVE_EDR,
+
+	/* TODO: explain these values */
+	WL12XX_CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_BR,
+	WL12XX_CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_BR,
+	WL12XX_CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_BR,
+	WL12XX_CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_BR,
+	WL12XX_CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_EDR,
+	WL12XX_CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_EDR,
+	WL12XX_CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_EDR,
+	WL12XX_CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_EDR,
+
+	WL12XX_CONF_SG_ACL_ACTIVE_SCAN_WLAN_BR,
+	WL12XX_CONF_SG_ACL_ACTIVE_SCAN_WLAN_EDR,
+	WL12XX_CONF_SG_ACL_PASSIVE_SCAN_BT_BR,
+	WL12XX_CONF_SG_ACL_PASSIVE_SCAN_WLAN_BR,
+	WL12XX_CONF_SG_ACL_PASSIVE_SCAN_BT_EDR,
+	WL12XX_CONF_SG_ACL_PASSIVE_SCAN_WLAN_EDR,
+
+	/*
+	* Compensation percentage of probe requests when scan initiated
+	* during BT voice/ACL link.
+	*
+	* Range: 0 - 255 (%)
+	*/
+	WL12XX_CONF_SG_AUTO_SCAN_PROBE_REQ,
+
+	/*
+	* Compensation percentage of probe requests when active scan initiated
+	* during BT voice
+	*
+	* Range: 0 - 255 (%)
+	*/
+	WL12XX_CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3,
+
+	/*
+	* Compensation percentage of WLAN active scan window if initiated
+	* during BT A2DP
+	*
+	* Range: 0 - 1000 (%)
+	*/
+	WL12XX_CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_A2DP,
+
+	/*
+	* Compensation percentage of WLAN passive scan window if initiated
+	* during BT A2DP BR
+	*
+	* Range: 0 - 1000 (%)
+	*/
+	WL12XX_CONF_SG_PASSIVE_SCAN_DUR_FACTOR_A2DP_BR,
+
+	/*
+	* Compensation percentage of WLAN passive scan window if initiated
+	* during BT A2DP EDR
+	*
+	* Range: 0 - 1000 (%)
+	*/
+	WL12XX_CONF_SG_PASSIVE_SCAN_DUR_FACTOR_A2DP_EDR,
+
+	/*
+	* Compensation percentage of WLAN passive scan window if initiated
+	* during BT voice
+	*
+	* Range: 0 - 1000 (%)
+	*/
+	WL12XX_CONF_SG_PASSIVE_SCAN_DUR_FACTOR_HV3,
+
+	/* TODO: explain these values */
+	WL12XX_CONF_SG_CONSECUTIVE_HV3_IN_PASSIVE_SCAN,
+	WL12XX_CONF_SG_BCN_HV3_COLL_THR_IN_PASSIVE_SCAN,
+	WL12XX_CONF_SG_TX_RX_PROTECT_BW_IN_PASSIVE_SCAN,
+
+	/*
+	* Defines whether the SG will force WLAN host to enter/exit PSM
+	*
+	* Range: 1 - SG can force, 0 - host handles PSM
+	*/
+	WL12XX_CONF_SG_STA_FORCE_PS_IN_BT_SCO,
+
+	/*
+	* Defines antenna configuration (single/dual antenna)
+	*
+	* Range: 0 - single antenna, 1 - dual antenna
+	*/
+	WL12XX_CONF_SG_ANTENNA_CONFIGURATION,
+
+	/*
+	* The threshold (percent) of max consecutive beacon misses before
+	* increasing priority of beacon reception.
+	*
+	* Range: 0 - 100 (%)
+	*/
+	WL12XX_CONF_SG_BEACON_MISS_PERCENT,
+
+	/*
+	* Protection time of the DHCP procedure.
+	*
+	* Range: 0 - 100000 (ms)
+	*/
+	WL12XX_CONF_SG_DHCP_TIME,
+
+	/*
+	* RX guard time before the beginning of a new BT voice frame during
+	* which no new WLAN trigger frame is transmitted.
+	*
+	* Range: 0 - 100000 (us)
+	*/
+	WL12XX_CONF_SG_RXT,
+
+	/*
+	* TX guard time before the beginning of a new BT voice frame during
+	* which no new WLAN frame is transmitted.
+	*
+	* Range: 0 - 100000 (us)
+	*/
+	WL12XX_CONF_SG_TXT,
+
+	/*
+	* Enable adaptive RXT/TXT algorithm. If disabled, the host values
+	* will be utilized.
+	*
+	* Range: 0 - disable, 1 - enable
+	*/
+	WL12XX_CONF_SG_ADAPTIVE_RXT_TXT,
+
+	/* TODO: explain this value */
+	WL12XX_CONF_SG_GENERAL_USAGE_BIT_MAP,
+
+	/*
+	* Number of consecutive BT voice frames not interrupted by WLAN
+	*
+	* Range: 0 - 100
+	*/
+	WL12XX_CONF_SG_HV3_MAX_SERVED,
+
+	/*
+	* The used WLAN legacy service period during active BT ACL link
+	*
+	* Range: 0 - 255 (ms)
+	*/
+	WL12XX_CONF_SG_PS_POLL_TIMEOUT,
+
+	/*
+	* The used WLAN UPSD service period during active BT ACL link
+	*
+	* Range: 0 - 255 (ms)
+	*/
+	WL12XX_CONF_SG_UPSD_TIMEOUT,
+
+	WL12XX_CONF_SG_CONSECUTIVE_CTS_THRESHOLD,
+	WL12XX_CONF_SG_STA_RX_WINDOW_AFTER_DTIM,
+	WL12XX_CONF_SG_STA_CONNECTION_PROTECTION_TIME,
+
+	/* AP params */
+	WL12XX_CONF_AP_BEACON_MISS_TX,
+	WL12XX_CONF_AP_RX_WINDOW_AFTER_BEACON,
+	WL12XX_CONF_AP_BEACON_WINDOW_INTERVAL,
+	WL12XX_CONF_AP_CONNECTION_PROTECTION_TIME,
+	WL12XX_CONF_AP_BT_ACL_VAL_BT_SERVE_TIME,
+	WL12XX_CONF_AP_BT_ACL_VAL_WL_SERVE_TIME,
+
+	/* CTS Diluting params */
+	WL12XX_CONF_SG_CTS_DILUTED_BAD_RX_PACKETS_TH,
+	WL12XX_CONF_SG_CTS_CHOP_IN_DUAL_ANT_SCO_MASTER,
+
+	WL12XX_CONF_SG_TEMP_PARAM_1,
+	WL12XX_CONF_SG_TEMP_PARAM_2,
+	WL12XX_CONF_SG_TEMP_PARAM_3,
+	WL12XX_CONF_SG_TEMP_PARAM_4,
+	WL12XX_CONF_SG_TEMP_PARAM_5,
+	WL12XX_CONF_SG_TEMP_PARAM_6,
+	WL12XX_CONF_SG_TEMP_PARAM_7,
+	WL12XX_CONF_SG_TEMP_PARAM_8,
+	WL12XX_CONF_SG_TEMP_PARAM_9,
+	WL12XX_CONF_SG_TEMP_PARAM_10,
+
+	WL12XX_CONF_SG_PARAMS_MAX,
+	WL12XX_CONF_SG_PARAMS_ALL = 0xff
+};
+
 #endif /* __WL12XX_CONF_H__ */
diff --git a/drivers/net/wireless/ti/wl12xx/main.c b/drivers/net/wireless/ti/wl12xx/main.c
index c9da828a3..adfb3e9de 100644
--- a/drivers/net/wireless/ti/wl12xx/main.c
+++ b/drivers/net/wireless/ti/wl12xx/main.c
@@ -39,6 +39,7 @@
 #include "scan.h"
 #include "event.h"
 #include "debugfs.h"
+#include "conf.h"
 
 static char *fref_param;
 static char *tcxo_param;
@@ -46,69 +47,69 @@ static char *tcxo_param;
 static struct wlcore_conf wl12xx_conf = {
 	.sg = {
 		.params = {
-			[CONF_SG_ACL_BT_MASTER_MIN_BR] = 10,
-			[CONF_SG_ACL_BT_MASTER_MAX_BR] = 180,
-			[CONF_SG_ACL_BT_SLAVE_MIN_BR] = 10,
-			[CONF_SG_ACL_BT_SLAVE_MAX_BR] = 180,
-			[CONF_SG_ACL_BT_MASTER_MIN_EDR] = 10,
-			[CONF_SG_ACL_BT_MASTER_MAX_EDR] = 80,
-			[CONF_SG_ACL_BT_SLAVE_MIN_EDR] = 10,
-			[CONF_SG_ACL_BT_SLAVE_MAX_EDR] = 80,
-			[CONF_SG_ACL_WLAN_PS_MASTER_BR] = 8,
-			[CONF_SG_ACL_WLAN_PS_SLAVE_BR] = 8,
-			[CONF_SG_ACL_WLAN_PS_MASTER_EDR] = 20,
-			[CONF_SG_ACL_WLAN_PS_SLAVE_EDR] = 20,
-			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_BR] = 20,
-			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_BR] = 35,
-			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_BR] = 16,
-			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_BR] = 35,
-			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_EDR] = 32,
-			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_EDR] = 50,
-			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_EDR] = 28,
-			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_EDR] = 50,
-			[CONF_SG_ACL_ACTIVE_SCAN_WLAN_BR] = 10,
-			[CONF_SG_ACL_ACTIVE_SCAN_WLAN_EDR] = 20,
-			[CONF_SG_ACL_PASSIVE_SCAN_BT_BR] = 75,
-			[CONF_SG_ACL_PASSIVE_SCAN_WLAN_BR] = 15,
-			[CONF_SG_ACL_PASSIVE_SCAN_BT_EDR] = 27,
-			[CONF_SG_ACL_PASSIVE_SCAN_WLAN_EDR] = 17,
+			[WL12XX_CONF_SG_ACL_BT_MASTER_MIN_BR] = 10,
+			[WL12XX_CONF_SG_ACL_BT_MASTER_MAX_BR] = 180,
+			[WL12XX_CONF_SG_ACL_BT_SLAVE_MIN_BR] = 10,
+			[WL12XX_CONF_SG_ACL_BT_SLAVE_MAX_BR] = 180,
+			[WL12XX_CONF_SG_ACL_BT_MASTER_MIN_EDR] = 10,
+			[WL12XX_CONF_SG_ACL_BT_MASTER_MAX_EDR] = 80,
+			[WL12XX_CONF_SG_ACL_BT_SLAVE_MIN_EDR] = 10,
+			[WL12XX_CONF_SG_ACL_BT_SLAVE_MAX_EDR] = 80,
+			[WL12XX_CONF_SG_ACL_WLAN_PS_MASTER_BR] = 8,
+			[WL12XX_CONF_SG_ACL_WLAN_PS_SLAVE_BR] = 8,
+			[WL12XX_CONF_SG_ACL_WLAN_PS_MASTER_EDR] = 20,
+			[WL12XX_CONF_SG_ACL_WLAN_PS_SLAVE_EDR] = 20,
+			[WL12XX_CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_BR] = 20,
+			[WL12XX_CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_BR] = 35,
+			[WL12XX_CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_BR] = 16,
+			[WL12XX_CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_BR] = 35,
+			[WL12XX_CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_EDR] = 32,
+			[WL12XX_CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_EDR] = 50,
+			[WL12XX_CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_EDR] = 28,
+			[WL12XX_CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_EDR] = 50,
+			[WL12XX_CONF_SG_ACL_ACTIVE_SCAN_WLAN_BR] = 10,
+			[WL12XX_CONF_SG_ACL_ACTIVE_SCAN_WLAN_EDR] = 20,
+			[WL12XX_CONF_SG_ACL_PASSIVE_SCAN_BT_BR] = 75,
+			[WL12XX_CONF_SG_ACL_PASSIVE_SCAN_WLAN_BR] = 15,
+			[WL12XX_CONF_SG_ACL_PASSIVE_SCAN_BT_EDR] = 27,
+			[WL12XX_CONF_SG_ACL_PASSIVE_SCAN_WLAN_EDR] = 17,
 			/* active scan params */
-			[CONF_SG_AUTO_SCAN_PROBE_REQ] = 170,
-			[CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3] = 50,
-			[CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_A2DP] = 100,
+			[WL12XX_CONF_SG_AUTO_SCAN_PROBE_REQ] = 170,
+			[WL12XX_CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3] = 50,
+			[WL12XX_CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_A2DP] = 100,
 			/* passive scan params */
-			[CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP_BR] = 800,
-			[CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP_EDR] = 200,
-			[CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_HV3] = 200,
+			[WL12XX_CONF_SG_PASSIVE_SCAN_DUR_FACTOR_A2DP_BR] = 800,
+			[WL12XX_CONF_SG_PASSIVE_SCAN_DUR_FACTOR_A2DP_EDR] = 200,
+			[WL12XX_CONF_SG_PASSIVE_SCAN_DUR_FACTOR_HV3] = 200,
 			/* passive scan in dual antenna params */
-			[CONF_SG_CONSECUTIVE_HV3_IN_PASSIVE_SCAN] = 0,
-			[CONF_SG_BCN_HV3_COLLISION_THRESH_IN_PASSIVE_SCAN] = 0,
-			[CONF_SG_TX_RX_PROTECTION_BWIDTH_IN_PASSIVE_SCAN] = 0,
+			[WL12XX_CONF_SG_CONSECUTIVE_HV3_IN_PASSIVE_SCAN] = 0,
+			[WL12XX_CONF_SG_BCN_HV3_COLL_THR_IN_PASSIVE_SCAN] = 0,
+			[WL12XX_CONF_SG_TX_RX_PROTECT_BW_IN_PASSIVE_SCAN] = 0,
 			/* general params */
-			[CONF_SG_STA_FORCE_PS_IN_BT_SCO] = 1,
-			[CONF_SG_ANTENNA_CONFIGURATION] = 0,
-			[CONF_SG_BEACON_MISS_PERCENT] = 60,
-			[CONF_SG_DHCP_TIME] = 5000,
-			[CONF_SG_RXT] = 1200,
-			[CONF_SG_TXT] = 1000,
-			[CONF_SG_ADAPTIVE_RXT_TXT] = 1,
-			[CONF_SG_GENERAL_USAGE_BIT_MAP] = 3,
-			[CONF_SG_HV3_MAX_SERVED] = 6,
-			[CONF_SG_PS_POLL_TIMEOUT] = 10,
-			[CONF_SG_UPSD_TIMEOUT] = 10,
-			[CONF_SG_CONSECUTIVE_CTS_THRESHOLD] = 2,
-			[CONF_SG_STA_RX_WINDOW_AFTER_DTIM] = 5,
-			[CONF_SG_STA_CONNECTION_PROTECTION_TIME] = 30,
+			[WL12XX_CONF_SG_STA_FORCE_PS_IN_BT_SCO] = 1,
+			[WL12XX_CONF_SG_ANTENNA_CONFIGURATION] = 0,
+			[WL12XX_CONF_SG_BEACON_MISS_PERCENT] = 60,
+			[WL12XX_CONF_SG_DHCP_TIME] = 5000,
+			[WL12XX_CONF_SG_RXT] = 1200,
+			[WL12XX_CONF_SG_TXT] = 1000,
+			[WL12XX_CONF_SG_ADAPTIVE_RXT_TXT] = 1,
+			[WL12XX_CONF_SG_GENERAL_USAGE_BIT_MAP] = 3,
+			[WL12XX_CONF_SG_HV3_MAX_SERVED] = 6,
+			[WL12XX_CONF_SG_PS_POLL_TIMEOUT] = 10,
+			[WL12XX_CONF_SG_UPSD_TIMEOUT] = 10,
+			[WL12XX_CONF_SG_CONSECUTIVE_CTS_THRESHOLD] = 2,
+			[WL12XX_CONF_SG_STA_RX_WINDOW_AFTER_DTIM] = 5,
+			[WL12XX_CONF_SG_STA_CONNECTION_PROTECTION_TIME] = 30,
 			/* AP params */
-			[CONF_AP_BEACON_MISS_TX] = 3,
-			[CONF_AP_RX_WINDOW_AFTER_BEACON] = 10,
-			[CONF_AP_BEACON_WINDOW_INTERVAL] = 2,
-			[CONF_AP_CONNECTION_PROTECTION_TIME] = 0,
-			[CONF_AP_BT_ACL_VAL_BT_SERVE_TIME] = 25,
-			[CONF_AP_BT_ACL_VAL_WL_SERVE_TIME] = 25,
+			[WL12XX_CONF_AP_BEACON_MISS_TX] = 3,
+			[WL12XX_CONF_AP_RX_WINDOW_AFTER_BEACON] = 10,
+			[WL12XX_CONF_AP_BEACON_WINDOW_INTERVAL] = 2,
+			[WL12XX_CONF_AP_CONNECTION_PROTECTION_TIME] = 0,
+			[WL12XX_CONF_AP_BT_ACL_VAL_BT_SERVE_TIME] = 25,
+			[WL12XX_CONF_AP_BT_ACL_VAL_WL_SERVE_TIME] = 25,
 			/* CTS Diluting params */
-			[CONF_SG_CTS_DILUTED_BAD_RX_PACKETS_TH] = 0,
-			[CONF_SG_CTS_CHOP_IN_DUAL_ANT_SCO_MASTER] = 0,
+			[WL12XX_CONF_SG_CTS_DILUTED_BAD_RX_PACKETS_TH] = 0,
+			[WL12XX_CONF_SG_CTS_CHOP_IN_DUAL_ANT_SCO_MASTER] = 0,
 		},
 		.state = CONF_SG_PROTECTIVE,
 	},
@@ -1809,6 +1810,7 @@ static int wl12xx_setup(struct wl1271 *wl)
 
 	BUILD_BUG_ON(WL12XX_MAX_LINKS > WLCORE_MAX_LINKS);
 	BUILD_BUG_ON(WL12XX_MAX_AP_STATIONS > WL12XX_MAX_LINKS);
+	BUILD_BUG_ON(WL12XX_CONF_SG_PARAMS_MAX > WLCORE_CONF_SG_PARAMS_MAX);
 
 	wl->rtable = wl12xx_rtable;
 	wl->num_tx_desc = WL12XX_NUM_TX_DESCRIPTORS;
diff --git a/drivers/net/wireless/ti/wl18xx/conf.h b/drivers/net/wireless/ti/wl18xx/conf.h
index 71f1ec448..7aa880f14 100644
--- a/drivers/net/wireless/ti/wl18xx/conf.h
+++ b/drivers/net/wireless/ti/wl18xx/conf.h
@@ -139,4 +139,94 @@ struct wl18xx_priv_conf {
 	struct conf_ap_sleep_settings ap_sleep;
 } __packed;
 
+enum wl18xx_sg_params {
+	WL18XX_CONF_SG_PARAM_0 = 0,
+
+	/* Configuration Parameters */
+	WL18XX_CONF_SG_ANTENNA_CONFIGURATION,
+	WL18XX_CONF_SG_ZIGBEE_COEX,
+	WL18XX_CONF_SG_TIME_SYNC,
+
+	WL18XX_CONF_SG_PARAM_4,
+	WL18XX_CONF_SG_PARAM_5,
+	WL18XX_CONF_SG_PARAM_6,
+	WL18XX_CONF_SG_PARAM_7,
+	WL18XX_CONF_SG_PARAM_8,
+	WL18XX_CONF_SG_PARAM_9,
+	WL18XX_CONF_SG_PARAM_10,
+	WL18XX_CONF_SG_PARAM_11,
+	WL18XX_CONF_SG_PARAM_12,
+	WL18XX_CONF_SG_PARAM_13,
+	WL18XX_CONF_SG_PARAM_14,
+	WL18XX_CONF_SG_PARAM_15,
+	WL18XX_CONF_SG_PARAM_16,
+	WL18XX_CONF_SG_PARAM_17,
+	WL18XX_CONF_SG_PARAM_18,
+	WL18XX_CONF_SG_PARAM_19,
+	WL18XX_CONF_SG_PARAM_20,
+	WL18XX_CONF_SG_PARAM_21,
+	WL18XX_CONF_SG_PARAM_22,
+	WL18XX_CONF_SG_PARAM_23,
+	WL18XX_CONF_SG_PARAM_24,
+	WL18XX_CONF_SG_PARAM_25,
+
+	/* Active Scan Parameters */
+	WL18XX_CONF_SG_AUTO_SCAN_PROBE_REQ,
+	WL18XX_CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3,
+
+	WL18XX_CONF_SG_PARAM_28,
+
+	/* Passive Scan Parameters */
+	WL18XX_CONF_SG_PARAM_29,
+	WL18XX_CONF_SG_PARAM_30,
+	WL18XX_CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_HV3,
+
+	/* Passive Scan in Dual Antenna Parameters */
+	WL18XX_CONF_SG_CONSECUTIVE_HV3_IN_PASSIVE_SCAN,
+	WL18XX_CONF_SG_BEACON_HV3_COLL_TH_IN_PASSIVE_SCAN,
+	WL18XX_CONF_SG_TX_RX_PROTECT_BW_IN_PASSIVE_SCAN,
+
+	/* General Parameters */
+	WL18XX_CONF_SG_STA_FORCE_PS_IN_BT_SCO,
+	WL18XX_CONF_SG_PARAM_36,
+	WL18XX_CONF_SG_BEACON_MISS_PERCENT,
+	WL18XX_CONF_SG_PARAM_38,
+	WL18XX_CONF_SG_RXT,
+	WL18XX_CONF_SG_UNUSED,
+	WL18XX_CONF_SG_ADAPTIVE_RXT_TXT,
+	WL18XX_CONF_SG_GENERAL_USAGE_BIT_MAP,
+	WL18XX_CONF_SG_HV3_MAX_SERVED,
+	WL18XX_CONF_SG_PARAM_44,
+	WL18XX_CONF_SG_PARAM_45,
+	WL18XX_CONF_SG_CONSECUTIVE_CTS_THRESHOLD,
+	WL18XX_CONF_SG_GEMINI_PARAM_47,
+	WL18XX_CONF_SG_STA_CONNECTION_PROTECTION_TIME,
+
+	/* AP Parameters */
+	WL18XX_CONF_SG_AP_BEACON_MISS_TX,
+	WL18XX_CONF_SG_PARAM_50,
+	WL18XX_CONF_SG_AP_BEACON_WINDOW_INTERVAL,
+	WL18XX_CONF_SG_AP_CONNECTION_PROTECTION_TIME,
+	WL18XX_CONF_SG_PARAM_53,
+	WL18XX_CONF_SG_PARAM_54,
+
+	/* CTS Diluting Parameters */
+	WL18XX_CONF_SG_CTS_DILUTED_BAD_RX_PACKETS_TH,
+	WL18XX_CONF_SG_CTS_CHOP_IN_DUAL_ANT_SCO_MASTER,
+
+	WL18XX_CONF_SG_TEMP_PARAM_1,
+	WL18XX_CONF_SG_TEMP_PARAM_2,
+	WL18XX_CONF_SG_TEMP_PARAM_3,
+	WL18XX_CONF_SG_TEMP_PARAM_4,
+	WL18XX_CONF_SG_TEMP_PARAM_5,
+	WL18XX_CONF_SG_TEMP_PARAM_6,
+	WL18XX_CONF_SG_TEMP_PARAM_7,
+	WL18XX_CONF_SG_TEMP_PARAM_8,
+	WL18XX_CONF_SG_TEMP_PARAM_9,
+	WL18XX_CONF_SG_TEMP_PARAM_10,
+
+	WL18XX_CONF_SG_PARAMS_MAX,
+	WL18XX_CONF_SG_PARAMS_ALL = 0xff
+};
+
 #endif /* __WL18XX_CONF_H__ */
diff --git a/drivers/net/wireless/ti/wl18xx/event.c b/drivers/net/wireless/ti/wl18xx/event.c
index 09c7e098f..719907a0a 100644
--- a/drivers/net/wireless/ti/wl18xx/event.c
+++ b/drivers/net/wireless/ti/wl18xx/event.c
@@ -205,6 +205,8 @@ int wl18xx_process_mailbox_events(struct wl1271 *wl)
 						 mbox->sc_ssid,
 						 mbox->sc_pwd_len,
 						 mbox->sc_pwd);
+	if (vector & FW_LOGGER_INDICATION)
+		wlcore_event_fw_logger(wl);
 
 	return 0;
 }
diff --git a/drivers/net/wireless/ti/wl18xx/event.h b/drivers/net/wireless/ti/wl18xx/event.h
index f3d4f1337..070de1274 100644
--- a/drivers/net/wireless/ti/wl18xx/event.h
+++ b/drivers/net/wireless/ti/wl18xx/event.h
@@ -41,6 +41,7 @@ enum {
 	SMART_CONFIG_SYNC_EVENT_ID               = BIT(22),
 	SMART_CONFIG_DECODE_EVENT_ID             = BIT(23),
 	TIME_SYNC_EVENT_ID                       = BIT(24),
+	FW_LOGGER_INDICATION			= BIT(25),
 };
 
 enum wl18xx_radar_types {
diff --git a/drivers/net/wireless/ti/wl18xx/main.c b/drivers/net/wireless/ti/wl18xx/main.c
index 42fbc0458..be21289c3 100644
--- a/drivers/net/wireless/ti/wl18xx/main.c
+++ b/drivers/net/wireless/ti/wl18xx/main.c
@@ -177,69 +177,80 @@ enum wl18xx_hw_rates {
 static struct wlcore_conf wl18xx_conf = {
 	.sg = {
 		.params = {
-			[CONF_SG_ACL_BT_MASTER_MIN_BR] = 10,
-			[CONF_SG_ACL_BT_MASTER_MAX_BR] = 180,
-			[CONF_SG_ACL_BT_SLAVE_MIN_BR] = 10,
-			[CONF_SG_ACL_BT_SLAVE_MAX_BR] = 180,
-			[CONF_SG_ACL_BT_MASTER_MIN_EDR] = 10,
-			[CONF_SG_ACL_BT_MASTER_MAX_EDR] = 80,
-			[CONF_SG_ACL_BT_SLAVE_MIN_EDR] = 10,
-			[CONF_SG_ACL_BT_SLAVE_MAX_EDR] = 80,
-			[CONF_SG_ACL_WLAN_PS_MASTER_BR] = 8,
-			[CONF_SG_ACL_WLAN_PS_SLAVE_BR] = 8,
-			[CONF_SG_ACL_WLAN_PS_MASTER_EDR] = 20,
-			[CONF_SG_ACL_WLAN_PS_SLAVE_EDR] = 20,
-			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_BR] = 20,
-			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_BR] = 35,
-			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_BR] = 16,
-			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_BR] = 35,
-			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_EDR] = 32,
-			[CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_EDR] = 50,
-			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_EDR] = 28,
-			[CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_EDR] = 50,
-			[CONF_SG_ACL_ACTIVE_SCAN_WLAN_BR] = 10,
-			[CONF_SG_ACL_ACTIVE_SCAN_WLAN_EDR] = 20,
-			[CONF_SG_ACL_PASSIVE_SCAN_BT_BR] = 75,
-			[CONF_SG_ACL_PASSIVE_SCAN_WLAN_BR] = 15,
-			[CONF_SG_ACL_PASSIVE_SCAN_BT_EDR] = 27,
-			[CONF_SG_ACL_PASSIVE_SCAN_WLAN_EDR] = 17,
-			/* active scan params */
-			[CONF_SG_AUTO_SCAN_PROBE_REQ] = 170,
-			[CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3] = 50,
-			[CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_A2DP] = 100,
-			/* passive scan params */
-			[CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP_BR] = 800,
-			[CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP_EDR] = 200,
-			[CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_HV3] = 200,
-			/* passive scan in dual antenna params */
-			[CONF_SG_CONSECUTIVE_HV3_IN_PASSIVE_SCAN] = 0,
-			[CONF_SG_BCN_HV3_COLLISION_THRESH_IN_PASSIVE_SCAN] = 0,
-			[CONF_SG_TX_RX_PROTECTION_BWIDTH_IN_PASSIVE_SCAN] = 0,
-			/* general params */
-			[CONF_SG_STA_FORCE_PS_IN_BT_SCO] = 1,
-			[CONF_SG_ANTENNA_CONFIGURATION] = 0,
-			[CONF_SG_BEACON_MISS_PERCENT] = 60,
-			[CONF_SG_DHCP_TIME] = 5000,
-			[CONF_SG_RXT] = 1200,
-			[CONF_SG_TXT] = 1000,
-			[CONF_SG_ADAPTIVE_RXT_TXT] = 1,
-			[CONF_SG_GENERAL_USAGE_BIT_MAP] = 3,
-			[CONF_SG_HV3_MAX_SERVED] = 6,
-			[CONF_SG_PS_POLL_TIMEOUT] = 10,
-			[CONF_SG_UPSD_TIMEOUT] = 10,
-			[CONF_SG_CONSECUTIVE_CTS_THRESHOLD] = 2,
-			[CONF_SG_STA_RX_WINDOW_AFTER_DTIM] = 5,
-			[CONF_SG_STA_CONNECTION_PROTECTION_TIME] = 30,
-			/* AP params */
-			[CONF_AP_BEACON_MISS_TX] = 3,
-			[CONF_AP_RX_WINDOW_AFTER_BEACON] = 10,
-			[CONF_AP_BEACON_WINDOW_INTERVAL] = 2,
-			[CONF_AP_CONNECTION_PROTECTION_TIME] = 0,
-			[CONF_AP_BT_ACL_VAL_BT_SERVE_TIME] = 25,
-			[CONF_AP_BT_ACL_VAL_WL_SERVE_TIME] = 25,
-			/* CTS Diluting params */
-			[CONF_SG_CTS_DILUTED_BAD_RX_PACKETS_TH] = 0,
-			[CONF_SG_CTS_CHOP_IN_DUAL_ANT_SCO_MASTER] = 0,
+			[WL18XX_CONF_SG_PARAM_0] = 0,
+			/* Configuartion Parameters */
+			[WL18XX_CONF_SG_ANTENNA_CONFIGURATION] = 0,
+			[WL18XX_CONF_SG_ZIGBEE_COEX] = 0,
+			[WL18XX_CONF_SG_TIME_SYNC] = 0,
+			[WL18XX_CONF_SG_PARAM_4] = 0,
+			[WL18XX_CONF_SG_PARAM_5] = 0,
+			[WL18XX_CONF_SG_PARAM_6] = 0,
+			[WL18XX_CONF_SG_PARAM_7] = 0,
+			[WL18XX_CONF_SG_PARAM_8] = 0,
+			[WL18XX_CONF_SG_PARAM_9] = 0,
+			[WL18XX_CONF_SG_PARAM_10] = 0,
+			[WL18XX_CONF_SG_PARAM_11] = 0,
+			[WL18XX_CONF_SG_PARAM_12] = 0,
+			[WL18XX_CONF_SG_PARAM_13] = 0,
+			[WL18XX_CONF_SG_PARAM_14] = 0,
+			[WL18XX_CONF_SG_PARAM_15] = 0,
+			[WL18XX_CONF_SG_PARAM_16] = 0,
+			[WL18XX_CONF_SG_PARAM_17] = 0,
+			[WL18XX_CONF_SG_PARAM_18] = 0,
+			[WL18XX_CONF_SG_PARAM_19] = 0,
+			[WL18XX_CONF_SG_PARAM_20] = 0,
+			[WL18XX_CONF_SG_PARAM_21] = 0,
+			[WL18XX_CONF_SG_PARAM_22] = 0,
+			[WL18XX_CONF_SG_PARAM_23] = 0,
+			[WL18XX_CONF_SG_PARAM_24] = 0,
+			[WL18XX_CONF_SG_PARAM_25] = 0,
+			/* Active Scan Parameters */
+			[WL18XX_CONF_SG_AUTO_SCAN_PROBE_REQ] = 170,
+			[WL18XX_CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3] = 50,
+			[WL18XX_CONF_SG_PARAM_28] = 0,
+			/* Passive Scan Parameters */
+			[WL18XX_CONF_SG_PARAM_29] = 0,
+			[WL18XX_CONF_SG_PARAM_30] = 0,
+			[WL18XX_CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_HV3] = 200,
+			/* Passive Scan in Dual Antenna Parameters */
+			[WL18XX_CONF_SG_CONSECUTIVE_HV3_IN_PASSIVE_SCAN] = 0,
+			[WL18XX_CONF_SG_BEACON_HV3_COLL_TH_IN_PASSIVE_SCAN] = 0,
+			[WL18XX_CONF_SG_TX_RX_PROTECT_BW_IN_PASSIVE_SCAN] = 0,
+			/* General Parameters */
+			[WL18XX_CONF_SG_STA_FORCE_PS_IN_BT_SCO] = 1,
+			[WL18XX_CONF_SG_PARAM_36] = 0,
+			[WL18XX_CONF_SG_BEACON_MISS_PERCENT] = 60,
+			[WL18XX_CONF_SG_PARAM_38] = 0,
+			[WL18XX_CONF_SG_RXT] = 1200,
+			[WL18XX_CONF_SG_UNUSED] = 0,
+			[WL18XX_CONF_SG_ADAPTIVE_RXT_TXT] = 1,
+			[WL18XX_CONF_SG_GENERAL_USAGE_BIT_MAP] = 3,
+			[WL18XX_CONF_SG_HV3_MAX_SERVED] = 6,
+			[WL18XX_CONF_SG_PARAM_44] = 0,
+			[WL18XX_CONF_SG_PARAM_45] = 0,
+			[WL18XX_CONF_SG_CONSECUTIVE_CTS_THRESHOLD] = 2,
+			[WL18XX_CONF_SG_GEMINI_PARAM_47] = 0,
+			[WL18XX_CONF_SG_STA_CONNECTION_PROTECTION_TIME] = 0,
+			/* AP Parameters */
+			[WL18XX_CONF_SG_AP_BEACON_MISS_TX] = 3,
+			[WL18XX_CONF_SG_PARAM_50] = 0,
+			[WL18XX_CONF_SG_AP_BEACON_WINDOW_INTERVAL] = 2,
+			[WL18XX_CONF_SG_AP_CONNECTION_PROTECTION_TIME] = 30,
+			[WL18XX_CONF_SG_PARAM_53] = 0,
+			[WL18XX_CONF_SG_PARAM_54] = 0,
+			/* CTS Diluting Parameters */
+			[WL18XX_CONF_SG_CTS_DILUTED_BAD_RX_PACKETS_TH] = 0,
+			[WL18XX_CONF_SG_CTS_CHOP_IN_DUAL_ANT_SCO_MASTER] = 0,
+			[WL18XX_CONF_SG_TEMP_PARAM_1] = 0,
+			[WL18XX_CONF_SG_TEMP_PARAM_2] = 0,
+			[WL18XX_CONF_SG_TEMP_PARAM_3] = 0,
+			[WL18XX_CONF_SG_TEMP_PARAM_4] = 0,
+			[WL18XX_CONF_SG_TEMP_PARAM_5] = 0,
+			[WL18XX_CONF_SG_TEMP_PARAM_6] = 0,
+			[WL18XX_CONF_SG_TEMP_PARAM_7] = 0,
+			[WL18XX_CONF_SG_TEMP_PARAM_8] = 0,
+			[WL18XX_CONF_SG_TEMP_PARAM_9] = 0,
+			[WL18XX_CONF_SG_TEMP_PARAM_10] = 0,
 		},
 		.state = CONF_SG_PROTECTIVE,
 	},
@@ -461,7 +472,7 @@ static struct wlcore_conf wl18xx_conf = {
 	},
 	.fwlog = {
 		.mode                         = WL12XX_FWLOG_CONTINUOUS,
-		.mem_blocks                   = 2,
+		.mem_blocks                   = 0,
 		.severity                     = 0,
 		.timestamp                    = WL12XX_FWLOG_TIMESTAMP_DISABLED,
 		.output                       = WL12XX_FWLOG_OUTPUT_DBG_PINS,
@@ -584,7 +595,7 @@ static const struct wlcore_partition_set wl18xx_ptable[PART_TABLE_LEN] = {
 		.mem  = { .start = 0x00A00000, .size  = 0x00012000 },
 		.reg  = { .start = 0x00807000, .size  = 0x00005000 },
 		.mem2 = { .start = 0x00800000, .size  = 0x0000B000 },
-		.mem3 = { .start = 0x00000000, .size  = 0x00000000 },
+		.mem3 = { .start = 0x00401594, .size  = 0x00001020 },
 	},
 	[PART_DOWN] = {
 		.mem  = { .start = 0x00000000, .size  = 0x00014000 },
@@ -602,7 +613,7 @@ static const struct wlcore_partition_set wl18xx_ptable[PART_TABLE_LEN] = {
 		.mem  = { .start = 0x00800000, .size  = 0x000050FC },
 		.reg  = { .start = 0x00B00404, .size  = 0x00001000 },
 		.mem2 = { .start = 0x00C00000, .size  = 0x00000400 },
-		.mem3 = { .start = 0x00000000, .size  = 0x00000000 },
+		.mem3 = { .start = 0x00401594, .size  = 0x00001020 },
 	},
 	[PART_PHY_INIT] = {
 		.mem  = { .start = WL18XX_PHY_INIT_MEM_ADDR,
@@ -1029,7 +1040,8 @@ static int wl18xx_boot(struct wl1271 *wl)
 		DFS_CHANNELS_CONFIG_COMPLETE_EVENT |
 		SMART_CONFIG_SYNC_EVENT_ID |
 		SMART_CONFIG_DECODE_EVENT_ID |
-		TIME_SYNC_EVENT_ID;
+		TIME_SYNC_EVENT_ID |
+		FW_LOGGER_INDICATION;
 
 	wl->ap_event_mask = MAX_TX_FAILURE_EVENT_ID;
 
@@ -1895,6 +1907,7 @@ static int wl18xx_setup(struct wl1271 *wl)
 
 	BUILD_BUG_ON(WL18XX_MAX_LINKS > WLCORE_MAX_LINKS);
 	BUILD_BUG_ON(WL18XX_MAX_AP_STATIONS > WL18XX_MAX_LINKS);
+	BUILD_BUG_ON(WL18XX_CONF_SG_PARAMS_MAX > WLCORE_CONF_SG_PARAMS_MAX);
 
 	wl->rtable = wl18xx_rtable;
 	wl->num_tx_desc = WL18XX_NUM_TX_DESCRIPTORS;
diff --git a/drivers/net/wireless/ti/wlcore/Kconfig b/drivers/net/wireless/ti/wlcore/Kconfig
index 7c099542b..969c9d79b 100644
--- a/drivers/net/wireless/ti/wlcore/Kconfig
+++ b/drivers/net/wireless/ti/wlcore/Kconfig
@@ -1,6 +1,6 @@
 config WLCORE
 	tristate "TI wlcore support"
-	depends on WL_TI && MAC80211
+	depends on MAC80211
 	select FW_LOADER
 	---help---
 	  This module contains the main code for TI WLAN chips.  It abstracts
diff --git a/drivers/net/wireless/ti/wlcore/acx.c b/drivers/net/wireless/ti/wlcore/acx.c
index f28fa3b50..26cc23f32 100644
--- a/drivers/net/wireless/ti/wlcore/acx.c
+++ b/drivers/net/wireless/ti/wlcore/acx.c
@@ -534,9 +534,9 @@ int wl12xx_acx_sg_cfg(struct wl1271 *wl)
 	}
 
 	/* BT-WLAN coext parameters */
-	for (i = 0; i < CONF_SG_PARAMS_MAX; i++)
+	for (i = 0; i < WLCORE_CONF_SG_PARAMS_MAX; i++)
 		param->params[i] = cpu_to_le32(c->params[i]);
-	param->param_idx = CONF_SG_PARAMS_ALL;
+	param->param_idx = WLCORE_CONF_SG_PARAMS_ALL;
 
 	ret = wl1271_cmd_configure(wl, ACX_SG_CFG, param, sizeof(*param));
 	if (ret < 0) {
diff --git a/drivers/net/wireless/ti/wlcore/acx.h b/drivers/net/wireless/ti/wlcore/acx.h
index 954d57ec9..0d61fae88 100644
--- a/drivers/net/wireless/ti/wlcore/acx.h
+++ b/drivers/net/wireless/ti/wlcore/acx.h
@@ -300,7 +300,7 @@ struct acx_bt_wlan_coex {
 struct acx_bt_wlan_coex_param {
 	struct acx_header header;
 
-	__le32 params[CONF_SG_PARAMS_MAX];
+	__le32 params[WLCORE_CONF_SG_PARAMS_MAX];
 	u8 param_idx;
 	u8 padding[3];
 } __packed;
diff --git a/drivers/net/wireless/ti/wlcore/cmd.h b/drivers/net/wireless/ti/wlcore/cmd.h
index 8dc46c0a4..e28e2f230 100644
--- a/drivers/net/wireless/ti/wlcore/cmd.h
+++ b/drivers/net/wireless/ti/wlcore/cmd.h
@@ -626,7 +626,6 @@ struct wl12xx_cmd_remove_peer {
  */
 enum wl12xx_fwlogger_log_mode {
 	WL12XX_FWLOG_CONTINUOUS,
-	WL12XX_FWLOG_ON_DEMAND
 };
 
 /* Include/exclude timestamps from the log messages */
diff --git a/drivers/net/wireless/ti/wlcore/conf.h b/drivers/net/wireless/ti/wlcore/conf.h
index 52a9d1b14..44d898fe0 100644
--- a/drivers/net/wireless/ti/wlcore/conf.h
+++ b/drivers/net/wireless/ti/wlcore/conf.h
@@ -110,242 +110,11 @@ enum {
 	CONF_SG_OPPORTUNISTIC
 };
 
-enum {
-	/*
-	 * Configure the min and max time BT gains the antenna
-	 * in WLAN / BT master basic rate
-	 *
-	 * Range: 0 - 255 (ms)
-	 */
-	CONF_SG_ACL_BT_MASTER_MIN_BR = 0,
-	CONF_SG_ACL_BT_MASTER_MAX_BR,
-
-	/*
-	 * Configure the min and max time BT gains the antenna
-	 * in WLAN / BT slave basic rate
-	 *
-	 * Range: 0 - 255 (ms)
-	 */
-	CONF_SG_ACL_BT_SLAVE_MIN_BR,
-	CONF_SG_ACL_BT_SLAVE_MAX_BR,
-
-	/*
-	 * Configure the min and max time BT gains the antenna
-	 * in WLAN / BT master EDR
-	 *
-	 * Range: 0 - 255 (ms)
-	 */
-	CONF_SG_ACL_BT_MASTER_MIN_EDR,
-	CONF_SG_ACL_BT_MASTER_MAX_EDR,
-
-	/*
-	 * Configure the min and max time BT gains the antenna
-	 * in WLAN / BT slave EDR
-	 *
-	 * Range: 0 - 255 (ms)
-	 */
-	CONF_SG_ACL_BT_SLAVE_MIN_EDR,
-	CONF_SG_ACL_BT_SLAVE_MAX_EDR,
-
-	/*
-	 * The maximum time WLAN can gain the antenna
-	 * in WLAN PSM / BT master/slave BR
-	 *
-	 * Range: 0 - 255 (ms)
-	 */
-	CONF_SG_ACL_WLAN_PS_MASTER_BR,
-	CONF_SG_ACL_WLAN_PS_SLAVE_BR,
-
-	/*
-	 * The maximum time WLAN can gain the antenna
-	 * in WLAN PSM / BT master/slave EDR
-	 *
-	 * Range: 0 - 255 (ms)
-	 */
-	CONF_SG_ACL_WLAN_PS_MASTER_EDR,
-	CONF_SG_ACL_WLAN_PS_SLAVE_EDR,
-
-	/* TODO: explain these values */
-	CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_BR,
-	CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_BR,
-	CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_BR,
-	CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_BR,
-	CONF_SG_ACL_WLAN_ACTIVE_MASTER_MIN_EDR,
-	CONF_SG_ACL_WLAN_ACTIVE_MASTER_MAX_EDR,
-	CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MIN_EDR,
-	CONF_SG_ACL_WLAN_ACTIVE_SLAVE_MAX_EDR,
-
-	CONF_SG_ACL_ACTIVE_SCAN_WLAN_BR,
-	CONF_SG_ACL_ACTIVE_SCAN_WLAN_EDR,
-	CONF_SG_ACL_PASSIVE_SCAN_BT_BR,
-	CONF_SG_ACL_PASSIVE_SCAN_WLAN_BR,
-	CONF_SG_ACL_PASSIVE_SCAN_BT_EDR,
-	CONF_SG_ACL_PASSIVE_SCAN_WLAN_EDR,
-
-	/*
-	 * Compensation percentage of probe requests when scan initiated
-	 * during BT voice/ACL link.
-	 *
-	 * Range: 0 - 255 (%)
-	 */
-	CONF_SG_AUTO_SCAN_PROBE_REQ,
-
-	/*
-	 * Compensation percentage of probe requests when active scan initiated
-	 * during BT voice
-	 *
-	 * Range: 0 - 255 (%)
-	 */
-	CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_HV3,
-
-	/*
-	 * Compensation percentage of WLAN active scan window if initiated
-	 * during BT A2DP
-	 *
-	 * Range: 0 - 1000 (%)
-	 */
-	CONF_SG_ACTIVE_SCAN_DURATION_FACTOR_A2DP,
-
-	/*
-	 * Compensation percentage of WLAN passive scan window if initiated
-	 * during BT A2DP BR
-	 *
-	 * Range: 0 - 1000 (%)
-	 */
-	CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP_BR,
-
-	/*
-	 * Compensation percentage of WLAN passive scan window if initiated
-	 * during BT A2DP EDR
-	 *
-	 * Range: 0 - 1000 (%)
-	 */
-	CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_A2DP_EDR,
-
-	/*
-	 * Compensation percentage of WLAN passive scan window if initiated
-	 * during BT voice
-	 *
-	 * Range: 0 - 1000 (%)
-	 */
-	CONF_SG_PASSIVE_SCAN_DURATION_FACTOR_HV3,
-
-	/* TODO: explain these values */
-	CONF_SG_CONSECUTIVE_HV3_IN_PASSIVE_SCAN,
-	CONF_SG_BCN_HV3_COLLISION_THRESH_IN_PASSIVE_SCAN,
-	CONF_SG_TX_RX_PROTECTION_BWIDTH_IN_PASSIVE_SCAN,
-
-	/*
-	 * Defines whether the SG will force WLAN host to enter/exit PSM
-	 *
-	 * Range: 1 - SG can force, 0 - host handles PSM
-	 */
-	CONF_SG_STA_FORCE_PS_IN_BT_SCO,
-
-	/*
-	 * Defines antenna configuration (single/dual antenna)
-	 *
-	 * Range: 0 - single antenna, 1 - dual antenna
-	 */
-	CONF_SG_ANTENNA_CONFIGURATION,
-
-	/*
-	 * The threshold (percent) of max consecutive beacon misses before
-	 * increasing priority of beacon reception.
-	 *
-	 * Range: 0 - 100 (%)
-	 */
-	CONF_SG_BEACON_MISS_PERCENT,
-
-	/*
-	 * Protection time of the DHCP procedure.
-	 *
-	 * Range: 0 - 100000 (ms)
-	 */
-	CONF_SG_DHCP_TIME,
-
-	/*
-	 * RX guard time before the beginning of a new BT voice frame during
-	 * which no new WLAN trigger frame is transmitted.
-	 *
-	 * Range: 0 - 100000 (us)
-	 */
-	CONF_SG_RXT,
-
-	/*
-	 * TX guard time before the beginning of a new BT voice frame during
-	 * which no new WLAN frame is transmitted.
-	 *
-	 * Range: 0 - 100000 (us)
-	 */
-
-	CONF_SG_TXT,
-
-	/*
-	 * Enable adaptive RXT/TXT algorithm. If disabled, the host values
-	 * will be utilized.
-	 *
-	 * Range: 0 - disable, 1 - enable
-	 */
-	CONF_SG_ADAPTIVE_RXT_TXT,
-
-	/* TODO: explain this value */
-	CONF_SG_GENERAL_USAGE_BIT_MAP,
-
-	/*
-	 * Number of consecutive BT voice frames not interrupted by WLAN
-	 *
-	 * Range: 0 - 100
-	 */
-	CONF_SG_HV3_MAX_SERVED,
-
-	/*
-	 * The used WLAN legacy service period during active BT ACL link
-	 *
-	 * Range: 0 - 255 (ms)
-	 */
-	CONF_SG_PS_POLL_TIMEOUT,
-
-	/*
-	 * The used WLAN UPSD service period during active BT ACL link
-	 *
-	 * Range: 0 - 255 (ms)
-	 */
-	CONF_SG_UPSD_TIMEOUT,
-
-	CONF_SG_CONSECUTIVE_CTS_THRESHOLD,
-	CONF_SG_STA_RX_WINDOW_AFTER_DTIM,
-	CONF_SG_STA_CONNECTION_PROTECTION_TIME,
-
-	/* AP params */
-	CONF_AP_BEACON_MISS_TX,
-	CONF_AP_RX_WINDOW_AFTER_BEACON,
-	CONF_AP_BEACON_WINDOW_INTERVAL,
-	CONF_AP_CONNECTION_PROTECTION_TIME,
-	CONF_AP_BT_ACL_VAL_BT_SERVE_TIME,
-	CONF_AP_BT_ACL_VAL_WL_SERVE_TIME,
-
-	/* CTS Diluting params */
-	CONF_SG_CTS_DILUTED_BAD_RX_PACKETS_TH,
-	CONF_SG_CTS_CHOP_IN_DUAL_ANT_SCO_MASTER,
-
-	CONF_SG_TEMP_PARAM_1,
-	CONF_SG_TEMP_PARAM_2,
-	CONF_SG_TEMP_PARAM_3,
-	CONF_SG_TEMP_PARAM_4,
-	CONF_SG_TEMP_PARAM_5,
-	CONF_SG_TEMP_PARAM_6,
-	CONF_SG_TEMP_PARAM_7,
-	CONF_SG_TEMP_PARAM_8,
-	CONF_SG_TEMP_PARAM_9,
-	CONF_SG_TEMP_PARAM_10,
-
-	CONF_SG_PARAMS_MAX,
-	CONF_SG_PARAMS_ALL = 0xff
-};
+#define WLCORE_CONF_SG_PARAMS_MAX 67
+#define WLCORE_CONF_SG_PARAMS_ALL 0xff
 
 struct conf_sg_settings {
-	u32 params[CONF_SG_PARAMS_MAX];
+	u32 params[WLCORE_CONF_SG_PARAMS_MAX];
 	u8 state;
 } __packed;
 
diff --git a/drivers/net/wireless/ti/wlcore/debugfs.c b/drivers/net/wireless/ti/wlcore/debugfs.c
index eb43f94a1..7f672f687 100644
--- a/drivers/net/wireless/ti/wlcore/debugfs.c
+++ b/drivers/net/wireless/ti/wlcore/debugfs.c
@@ -1205,26 +1205,11 @@ err_out:
 
 static loff_t dev_mem_seek(struct file *file, loff_t offset, int orig)
 {
-	loff_t ret;
-
 	/* only requests of dword-aligned size and offset are supported */
 	if (offset % 4)
 		return -EINVAL;
 
-	switch (orig) {
-	case SEEK_SET:
-		file->f_pos = offset;
-		ret = file->f_pos;
-		break;
-	case SEEK_CUR:
-		file->f_pos += offset;
-		ret = file->f_pos;
-		break;
-	default:
-		ret = -EINVAL;
-	}
-
-	return ret;
+	return no_seek_end_llseek(file, offset, orig);
 }
 
 static const struct file_operations dev_mem_ops = {
@@ -1234,6 +1219,65 @@ static const struct file_operations dev_mem_ops = {
 	.llseek = dev_mem_seek,
 };
 
+static ssize_t fw_logger_read(struct file *file, char __user *user_buf,
+			      size_t count, loff_t *ppos)
+{
+	struct wl1271 *wl = file->private_data;
+
+	return wl1271_format_buffer(user_buf, count,
+					ppos, "%d\n",
+					wl->conf.fwlog.output);
+}
+
+static ssize_t fw_logger_write(struct file *file,
+			       const char __user *user_buf,
+			       size_t count, loff_t *ppos)
+{
+	struct wl1271 *wl = file->private_data;
+	unsigned long value;
+	int ret;
+
+	ret = kstrtoul_from_user(user_buf, count, 0, &value);
+	if (ret < 0) {
+		wl1271_warning("illegal value in fw_logger");
+		return -EINVAL;
+	}
+
+	if ((value > 2) || (value == 0)) {
+		wl1271_warning("fw_logger value must be 1-UART 2-SDIO");
+		return -ERANGE;
+	}
+
+	if (wl->conf.fwlog.output == 0) {
+		wl1271_warning("iligal opperation - fw logger disabled by default, please change mode via wlconf");
+		return -EINVAL;
+	}
+
+	mutex_lock(&wl->mutex);
+	ret = wl1271_ps_elp_wakeup(wl);
+	if (ret < 0) {
+		count = ret;
+		goto out;
+	}
+
+	wl->conf.fwlog.output = value;
+
+	ret = wl12xx_cmd_config_fwlog(wl);
+
+	wl1271_ps_elp_sleep(wl);
+
+out:
+	mutex_unlock(&wl->mutex);
+	return count;
+}
+
+static const struct file_operations fw_logger_ops = {
+	.open = simple_open,
+	.read = fw_logger_read,
+	.write = fw_logger_write,
+	.llseek = default_llseek,
+};
+
 static int wl1271_debugfs_add_files(struct wl1271 *wl,
 				    struct dentry *rootdir)
 {
@@ -1260,6 +1304,7 @@ static int wl1271_debugfs_add_files(struct wl1271 *wl,
 	DEBUGFS_ADD(irq_timeout, rootdir);
 	DEBUGFS_ADD(fw_stats_raw, rootdir);
 	DEBUGFS_ADD(sleep_auth, rootdir);
+	DEBUGFS_ADD(fw_logger, rootdir);
 
 	streaming = debugfs_create_dir("rx_streaming", rootdir);
 	if (!streaming || IS_ERR(streaming))
diff --git a/drivers/net/wireless/ti/wlcore/event.c b/drivers/net/wireless/ti/wlcore/event.c
index c42e78955..c96405498 100644
--- a/drivers/net/wireless/ti/wlcore/event.c
+++ b/drivers/net/wireless/ti/wlcore/event.c
@@ -28,6 +28,88 @@
 #include "ps.h"
 #include "scan.h"
 #include "wl12xx_80211.h"
+#include "hw_ops.h"
+
+#define WL18XX_LOGGER_SDIO_BUFF_MAX	(0x1020)
+#define WL18XX_DATA_RAM_BASE_ADDRESS	(0x20000000)
+#define WL18XX_LOGGER_SDIO_BUFF_ADDR	(0x40159c)
+#define WL18XX_LOGGER_BUFF_OFFSET	(sizeof(struct fw_logger_information))
+#define WL18XX_LOGGER_READ_POINT_OFFSET		(12)
+
+int wlcore_event_fw_logger(struct wl1271 *wl)
+{
+	u32 ret;
+	struct fw_logger_information fw_log;
+	u8  *buffer;
+	u32 internal_fw_addrbase = WL18XX_DATA_RAM_BASE_ADDRESS;
+	u32 addr = WL18XX_LOGGER_SDIO_BUFF_ADDR;
+	u32 end_buff_addr = WL18XX_LOGGER_SDIO_BUFF_ADDR +
+				WL18XX_LOGGER_BUFF_OFFSET;
+	u32 available_len;
+	u32 actual_len;
+	u32 clear_addr;
+	size_t len;
+	u32 start_loc;
+
+	buffer = kzalloc(WL18XX_LOGGER_SDIO_BUFF_MAX, GFP_KERNEL);
+	if (!buffer) {
+		wl1271_error("Fail to allocate fw logger memory");
+		fw_log.actual_buff_size = cpu_to_le32(0);
+		goto out;
+	}
+
+	ret = wlcore_read(wl, addr, buffer, WL18XX_LOGGER_SDIO_BUFF_MAX,
+			  false);
+	if (ret < 0) {
+		wl1271_error("Fail to read logger buffer, error_id = %d",
+			     ret);
+		fw_log.actual_buff_size = cpu_to_le32(0);
+		goto free_out;
+	}
+
+	memcpy(&fw_log, buffer, sizeof(fw_log));
+
+	if (le32_to_cpu(fw_log.actual_buff_size) == 0)
+		goto free_out;
+
+	actual_len = le32_to_cpu(fw_log.actual_buff_size);
+	start_loc = (le32_to_cpu(fw_log.buff_read_ptr) -
+			internal_fw_addrbase) - addr;
+	end_buff_addr += le32_to_cpu(fw_log.max_buff_size);
+	available_len = end_buff_addr -
+			(le32_to_cpu(fw_log.buff_read_ptr) -
+				 internal_fw_addrbase);
+	actual_len = min(actual_len, available_len);
+	len = actual_len;
+
+	wl12xx_copy_fwlog(wl, &buffer[start_loc], len);
+	clear_addr = addr + start_loc + le32_to_cpu(fw_log.actual_buff_size) +
+			internal_fw_addrbase;
+
+	len = le32_to_cpu(fw_log.actual_buff_size) - len;
+	if (len) {
+		wl12xx_copy_fwlog(wl,
+				  &buffer[WL18XX_LOGGER_BUFF_OFFSET],
+				  len);
+		clear_addr = addr + WL18XX_LOGGER_BUFF_OFFSET + len +
+				internal_fw_addrbase;
+	}
+
+	/* double check that clear address and write pointer are the same */
+	if (clear_addr != le32_to_cpu(fw_log.buff_write_ptr)) {
+		wl1271_error("Calculate of clear addr Clear = %x, write = %x",
+			     clear_addr, le32_to_cpu(fw_log.buff_write_ptr));
+	}
+
+	/* indicate FW about Clear buffer */
+	ret = wlcore_write32(wl, addr + WL18XX_LOGGER_READ_POINT_OFFSET,
+			     fw_log.buff_write_ptr);
+free_out:
+	kfree(buffer);
+out:
+	return le32_to_cpu(fw_log.actual_buff_size);
+}
+EXPORT_SYMBOL_GPL(wlcore_event_fw_logger);
 
 void wlcore_event_rssi_trigger(struct wl1271 *wl, s8 *metric_arr)
 {
diff --git a/drivers/net/wireless/ti/wlcore/event.h b/drivers/net/wireless/ti/wlcore/event.h
index acc7a59d3..75e8e98da 100644
--- a/drivers/net/wireless/ti/wlcore/event.h
+++ b/drivers/net/wireless/ti/wlcore/event.h
@@ -64,6 +64,14 @@ enum {
 
 #define NUM_OF_RSSI_SNR_TRIGGERS 8
 
+struct fw_logger_information {
+	__le32 max_buff_size;
+	__le32 actual_buff_size;
+	__le32 num_trace_drop;
+	__le32 buff_read_ptr;
+	__le32 buff_write_ptr;
+} __packed;
+
 struct wl1271;
 
 int wl1271_event_unmask(struct wl1271 *wl);
@@ -84,4 +92,5 @@ void wlcore_event_max_tx_failure(struct wl1271 *wl, unsigned long sta_bitmap);
 void wlcore_event_inactive_sta(struct wl1271 *wl, unsigned long sta_bitmap);
 void wlcore_event_roc_complete(struct wl1271 *wl);
 void wlcore_event_rssi_trigger(struct wl1271 *wl, s8 *metric_arr);
+int  wlcore_event_fw_logger(struct wl1271 *wl);
 #endif
diff --git a/drivers/net/wireless/ti/wlcore/io.c b/drivers/net/wireless/ti/wlcore/io.c
index 68e74eefd..564ca750c 100644
--- a/drivers/net/wireless/ti/wlcore/io.c
+++ b/drivers/net/wireless/ti/wlcore/io.c
@@ -175,12 +175,13 @@ int wlcore_set_partition(struct wl1271 *wl,
 	if (ret < 0)
 		goto out;
 
-	/*
-	 * We don't need the size of the last partition, as it is
+	/* We don't need the size of the last partition, as it is
 	 * automatically calculated based on the total memory size and
 	 * the sizes of the previous partitions.
 	 */
 	ret = wlcore_raw_write32(wl, HW_PART3_START_ADDR, p->mem3.start);
+	if (ret < 0)
+		goto out;
 
 out:
 	return ret;
diff --git a/drivers/net/wireless/ti/wlcore/main.c b/drivers/net/wireless/ti/wlcore/main.c
index 67bb798f1..c098a1195 100644
--- a/drivers/net/wireless/ti/wlcore/main.c
+++ b/drivers/net/wireless/ti/wlcore/main.c
@@ -1,4 +1,3 @@
-
 /*
  * This file is part of wlcore
  *
@@ -303,25 +302,11 @@ out:
 
 static void wlcore_adjust_conf(struct wl1271 *wl)
 {
-	/* Adjust settings according to optional module parameters */
-
-	/* Firmware Logger params */
-	if (fwlog_mem_blocks != -1) {
-		if (fwlog_mem_blocks >= CONF_FWLOG_MIN_MEM_BLOCKS &&
-		    fwlog_mem_blocks <= CONF_FWLOG_MAX_MEM_BLOCKS) {
-			wl->conf.fwlog.mem_blocks = fwlog_mem_blocks;
-		} else {
-			wl1271_error(
-				"Illegal fwlog_mem_blocks=%d using default %d",
-				fwlog_mem_blocks, wl->conf.fwlog.mem_blocks);
-		}
-	}
 
 	if (fwlog_param) {
 		if (!strcmp(fwlog_param, "continuous")) {
 			wl->conf.fwlog.mode = WL12XX_FWLOG_CONTINUOUS;
-		} else if (!strcmp(fwlog_param, "ondemand")) {
-			wl->conf.fwlog.mode = WL12XX_FWLOG_ON_DEMAND;
+			wl->conf.fwlog.output = WL12XX_FWLOG_OUTPUT_HOST;
 		} else if (!strcmp(fwlog_param, "dbgpins")) {
 			wl->conf.fwlog.mode = WL12XX_FWLOG_CONTINUOUS;
 			wl->conf.fwlog.output = WL12XX_FWLOG_OUTPUT_DBG_PINS;
@@ -825,91 +810,32 @@ size_t wl12xx_copy_fwlog(struct wl1271 *wl, u8 *memblock, size_t maxlen)
 
 static void wl12xx_read_fwlog_panic(struct wl1271 *wl)
 {
-	struct wlcore_partition_set part, old_part;
-	u32 addr;
-	u32 offset;
-	u32 end_of_log;
-	u8 *block;
-	int ret;
+	u32 end_of_log = 0;
 
-	if ((wl->quirks & WLCORE_QUIRK_FWLOG_NOT_IMPLEMENTED) ||
-	    (wl->conf.fwlog.mem_blocks == 0))
+	if (wl->quirks & WLCORE_QUIRK_FWLOG_NOT_IMPLEMENTED)
 		return;
 
 	wl1271_info("Reading FW panic log");
 
-	block = kmalloc(wl->fw_mem_block_size, GFP_KERNEL);
-	if (!block)
-		return;
-
 	/*
 	 * Make sure the chip is awake and the logger isn't active.
 	 * Do not send a stop fwlog command if the fw is hanged or if
 	 * dbgpins are used (due to some fw bug).
 	 */
 	if (wl1271_ps_elp_wakeup(wl))
-		goto out;
+		return;
 	if (!wl->watchdog_recovery &&
 	    wl->conf.fwlog.output != WL12XX_FWLOG_OUTPUT_DBG_PINS)
 		wl12xx_cmd_stop_fwlog(wl);
 
-	/* Read the first memory block address */
-	ret = wlcore_fw_status(wl, wl->fw_status);
-	if (ret < 0)
-		goto out;
-
-	addr = wl->fw_status->log_start_addr;
-	if (!addr)
-		goto out;
-
-	if (wl->conf.fwlog.mode == WL12XX_FWLOG_CONTINUOUS) {
-		offset = sizeof(addr) + sizeof(struct wl1271_rx_descriptor);
-		end_of_log = wl->fwlog_end;
-	} else {
-		offset = sizeof(addr);
-		end_of_log = addr;
-	}
-
-	old_part = wl->curr_part;
-	memset(&part, 0, sizeof(part));
-
 	/* Traverse the memory blocks linked list */
 	do {
-		part.mem.start = wlcore_hw_convert_hwaddr(wl, addr);
-		part.mem.size  = PAGE_SIZE;
-
-		ret = wlcore_set_partition(wl, &part);
-		if (ret < 0) {
-			wl1271_error("%s: set_partition start=0x%X size=%d",
-				__func__, part.mem.start, part.mem.size);
-			goto out;
+		end_of_log = wlcore_event_fw_logger(wl);
+		if (end_of_log == 0) {
+			msleep(100);
+			end_of_log = wlcore_event_fw_logger(wl);
 		}
-
-		memset(block, 0, wl->fw_mem_block_size);
-		ret = wlcore_read_hwaddr(wl, addr, block,
-					wl->fw_mem_block_size, false);
-
-		if (ret < 0)
-			goto out;
-
-		/*
-		 * Memory blocks are linked to one another. The first 4 bytes
-		 * of each memory block hold the hardware address of the next
-		 * one. The last memory block points to the first one in
-		 * on demand mode and is equal to 0x2000000 in continuous mode.
-		 */
-		addr = le32_to_cpup((__le32 *)block);
-
-		if (!wl12xx_copy_fwlog(wl, block + offset,
-					wl->fw_mem_block_size - offset))
-			break;
-	} while (addr && (addr != end_of_log));
-
-	wake_up_interruptible(&wl->fwlog_waitq);
-
-out:
-	kfree(block);
-	wlcore_set_partition(wl, &old_part);
+	} while (end_of_log != 0);
 }
 
 static void wlcore_save_freed_pkts(struct wl1271 *wl, struct wl12xx_vif *wlvif,
@@ -6291,7 +6217,6 @@ struct ieee80211_hw *wlcore_alloc_hw(size_t priv_size, u32 aggr_buf_size,
 	wl->active_sta_count = 0;
 	wl->active_link_count = 0;
 	wl->fwlog_size = 0;
-	init_waitqueue_head(&wl->fwlog_waitq);
 
 	/* The system link is always allocated */
 	__set_bit(WL12XX_SYSTEM_HLID, wl->links_map);
@@ -6377,7 +6302,6 @@ int wlcore_free_hw(struct wl1271 *wl)
 	/* Unblock any fwlog readers */
 	mutex_lock(&wl->mutex);
 	wl->fwlog_size = -1;
-	wake_up_interruptible_all(&wl->fwlog_waitq);
 	mutex_unlock(&wl->mutex);
 
 	wlcore_sysfs_free(wl);
@@ -6584,7 +6508,7 @@ MODULE_PARM_DESC(debug_level, "wl12xx debugging level");
 
 module_param_named(fwlog, fwlog_param, charp, 0);
 MODULE_PARM_DESC(fwlog,
-		 "FW logger options: continuous, ondemand, dbgpins or disable");
+		 "FW logger options: continuous, dbgpins or disable");
 
 module_param(fwlog_mem_blocks, int, S_IRUSR | S_IWUSR);
 MODULE_PARM_DESC(fwlog_mem_blocks, "fwlog mem_blocks");
diff --git a/drivers/net/wireless/ti/wlcore/rx.c b/drivers/net/wireless/ti/wlcore/rx.c
index 5b2927391..34e7e938e 100644
--- a/drivers/net/wireless/ti/wlcore/rx.c
+++ b/drivers/net/wireless/ti/wlcore/rx.c
@@ -149,7 +149,6 @@ static int wl1271_rx_handle_data(struct wl1271 *wl, u8 *data, u32 length,
 	if (desc->packet_class == WL12XX_RX_CLASS_LOGGER) {
 		size_t len = length - sizeof(*desc);
 		wl12xx_copy_fwlog(wl, data + sizeof(*desc), len);
-		wake_up_interruptible(&wl->fwlog_waitq);
 		return 0;
 	}
 
diff --git a/drivers/net/wireless/ti/wlcore/sysfs.c b/drivers/net/wireless/ti/wlcore/sysfs.c
index 24dd288d6..a9218e5b0 100644
--- a/drivers/net/wireless/ti/wlcore/sysfs.c
+++ b/drivers/net/wireless/ti/wlcore/sysfs.c
@@ -119,32 +119,6 @@ static ssize_t wl1271_sysfs_read_fwlog(struct file *filp, struct kobject *kobj,
 	if (ret < 0)
 		return -ERESTARTSYS;
 
-	/* Let only one thread read the log at a time, blocking others */
-	while (wl->fwlog_size == 0) {
-		DEFINE_WAIT(wait);
-
-		prepare_to_wait_exclusive(&wl->fwlog_waitq,
-					  &wait,
-					  TASK_INTERRUPTIBLE);
-
-		if (wl->fwlog_size != 0) {
-			finish_wait(&wl->fwlog_waitq, &wait);
-			break;
-		}
-
-		mutex_unlock(&wl->mutex);
-
-		schedule();
-		finish_wait(&wl->fwlog_waitq, &wait);
-
-		if (signal_pending(current))
-			return -ERESTARTSYS;
-
-		ret = mutex_lock_interruptible(&wl->mutex);
-		if (ret < 0)
-			return -ERESTARTSYS;
-	}
-
 	/* Check if the fwlog is still valid */
 	if (wl->fwlog_size < 0) {
 		mutex_unlock(&wl->mutex);
diff --git a/drivers/net/wireless/ti/wlcore/wlcore.h b/drivers/net/wireless/ti/wlcore/wlcore.h
index 906be6aa4..dda01b118 100644
--- a/drivers/net/wireless/ti/wlcore/wlcore.h
+++ b/drivers/net/wireless/ti/wlcore/wlcore.h
@@ -310,9 +310,6 @@ struct wl1271 {
 	/* FW memory block size */
 	u32 fw_mem_block_size;
 
-	/* Sysfs FW log entry readers wait queue */
-	wait_queue_head_t fwlog_waitq;
-
 	/* Hardware recovery work */
 	struct work_struct recovery_work;
 	bool watchdog_recovery;