Initial import

1 files changed, 330 insertions, 0 deletions

diff --git a/drivers/scsi/isci/probe_roms.h b/drivers/scsi/isci/probe_roms.h
new file mode 100644
index 000000000..e08b57824
--- /dev/null
+++ b/drivers/scsi/isci/probe_roms.h
@@ -0,0 +1,330 @@
+/*
+ * This file is provided under a dual BSD/GPLv2 license.  When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * GPL LICENSE SUMMARY
+ *
+ * Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
+ * The full GNU General Public License is included in this distribution
+ * in the file called LICENSE.GPL.
+ *
+ * BSD LICENSE
+ *
+ * Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ *   * Redistributions of source code must retain the above copyright
+ *     notice, this list of conditions and the following disclaimer.
+ *   * Redistributions in binary form must reproduce the above copyright
+ *     notice, this list of conditions and the following disclaimer in
+ *     the documentation and/or other materials provided with the
+ *     distribution.
+ *   * Neither the name of Intel Corporation nor the names of its
+ *     contributors may be used to endorse or promote products derived
+ *     from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+#ifndef _ISCI_PROBE_ROMS_H_
+#define _ISCI_PROBE_ROMS_H_
+
+#ifdef __KERNEL__
+#include <linux/firmware.h>
+#include <linux/pci.h>
+#include <linux/efi.h>
+#include "isci.h"
+
+#define SCIC_SDS_PARM_NO_SPEED   0
+
+/* generation 1 (i.e. 1.5 Gb/s) */
+#define SCIC_SDS_PARM_GEN1_SPEED 1
+
+/* generation 2 (i.e. 3.0 Gb/s) */
+#define SCIC_SDS_PARM_GEN2_SPEED 2
+
+/* generation 3 (i.e. 6.0 Gb/s) */
+#define SCIC_SDS_PARM_GEN3_SPEED 3
+#define SCIC_SDS_PARM_MAX_SPEED SCIC_SDS_PARM_GEN3_SPEED
+
+/* parameters that can be set by module parameters */
+struct sci_user_parameters {
+	struct sci_phy_user_params {
+		/**
+		 * This field specifies the NOTIFY (ENABLE SPIN UP) primitive
+		 * insertion frequency for this phy index.
+		 */
+		u32 notify_enable_spin_up_insertion_frequency;
+
+		/**
+		 * This method specifies the number of transmitted DWORDs within which
+		 * to transmit a single ALIGN primitive.  This value applies regardless
+		 * of what type of device is attached or connection state.  A value of
+		 * 0 indicates that no ALIGN primitives will be inserted.
+		 */
+		u16 align_insertion_frequency;
+
+		/**
+		 * This method specifies the number of transmitted DWORDs within which
+		 * to transmit 2 ALIGN primitives.  This applies for SAS connections
+		 * only.  A minimum value of 3 is required for this field.
+		 */
+		u16 in_connection_align_insertion_frequency;
+
+		/**
+		 * This field indicates the maximum speed generation to be utilized
+		 * by phys in the supplied port.
+		 * - A value of 1 indicates generation 1 (i.e. 1.5 Gb/s).
+		 * - A value of 2 indicates generation 2 (i.e. 3.0 Gb/s).
+		 * - A value of 3 indicates generation 3 (i.e. 6.0 Gb/s).
+		 */
+		u8 max_speed_generation;
+
+	} phys[SCI_MAX_PHYS];
+
+	/**
+	 * This field specifies the maximum number of direct attached devices
+	 * that can have power supplied to them simultaneously.
+	 */
+	u8 max_concurr_spinup;
+
+	/**
+	 * This field specifies the number of seconds to allow a phy to consume
+	 * power before yielding to another phy.
+	 *
+	 */
+	u8 phy_spin_up_delay_interval;
+
+	/**
+	 * These timer values specifies how long a link will remain open with no
+	 * activity in increments of a microsecond, it can be in increments of
+	 * 100 microseconds if the upper most bit is set.
+	 *
+	 */
+	u16 stp_inactivity_timeout;
+	u16 ssp_inactivity_timeout;
+
+	/**
+	 * These timer values specifies how long a link will remain open in increments
+	 * of 100 microseconds.
+	 *
+	 */
+	u16 stp_max_occupancy_timeout;
+	u16 ssp_max_occupancy_timeout;
+
+	/**
+	 * This timer value specifies how long a link will remain open with no
+	 * outbound traffic in increments of a microsecond.
+	 *
+	 */
+	u8 no_outbound_task_timeout;
+
+};
+
+#define SCIC_SDS_PARM_PHY_MASK_MIN 0x0
+#define SCIC_SDS_PARM_PHY_MASK_MAX 0xF
+#define MAX_CONCURRENT_DEVICE_SPIN_UP_COUNT 4
+
+struct sci_oem_params;
+int sci_oem_parameters_validate(struct sci_oem_params *oem, u8 version);
+
+struct isci_orom;
+struct isci_orom *isci_request_oprom(struct pci_dev *pdev);
+struct isci_orom *isci_request_firmware(struct pci_dev *pdev, const struct firmware *fw);
+struct isci_orom *isci_get_efi_var(struct pci_dev *pdev);
+
+struct isci_oem_hdr {
+	u8 sig[4];
+	u8 rev_major;
+	u8 rev_minor;
+	u16 len;
+	u8 checksum;
+	u8 reserved1;
+	u16 reserved2;
+} __attribute__ ((packed));
+
+#else
+#define SCI_MAX_PORTS 4
+#define SCI_MAX_PHYS 4
+#define SCI_MAX_CONTROLLERS 2
+#endif
+
+#define ISCI_FW_NAME		"isci/isci_firmware.bin"
+
+#define ROMSIGNATURE		0xaa55
+
+#define ISCI_OEM_SIG		"$OEM"
+#define ISCI_OEM_SIG_SIZE	4
+#define ISCI_ROM_SIG		"ISCUOEMB"
+#define ISCI_ROM_SIG_SIZE	8
+
+#define ISCI_EFI_VENDOR_GUID	\
+	EFI_GUID(0x193dfefa, 0xa445, 0x4302, 0x99, 0xd8, 0xef, 0x3a, 0xad, \
+			0x1a, 0x04, 0xc6)
+#define ISCI_EFI_VAR_NAME	"RstScuO"
+
+#define ISCI_ROM_VER_1_0	0x10
+#define ISCI_ROM_VER_1_1	0x11
+#define ISCI_ROM_VER_1_3	0x13
+#define ISCI_ROM_VER_LATEST	ISCI_ROM_VER_1_3
+
+/* Allowed PORT configuration modes APC Automatic PORT configuration mode is
+ * defined by the OEM configuration parameters providing no PHY_MASK parameters
+ * for any PORT. i.e. There are no phys assigned to any of the ports at start.
+ * MPC Manual PORT configuration mode is defined by the OEM configuration
+ * parameters providing a PHY_MASK value for any PORT.  It is assumed that any
+ * PORT with no PHY_MASK is an invalid port and not all PHYs must be assigned.
+ * A PORT_PHY mask that assigns just a single PHY to a port and no other PHYs
+ * being assigned is sufficient to declare manual PORT configuration.
+ */
+enum sci_port_configuration_mode {
+	SCIC_PORT_MANUAL_CONFIGURATION_MODE = 0,
+	SCIC_PORT_AUTOMATIC_CONFIGURATION_MODE = 1
+};
+
+struct sci_bios_oem_param_block_hdr {
+	uint8_t signature[ISCI_ROM_SIG_SIZE];
+	uint16_t total_block_length;
+	uint8_t hdr_length;
+	uint8_t version;
+	uint8_t preboot_source;
+	uint8_t num_elements;
+	uint16_t element_length;
+	uint8_t reserved[8];
+} __attribute__ ((packed));
+
+struct sci_oem_params {
+	struct {
+		uint8_t mode_type;
+		uint8_t max_concurr_spin_up;
+		/*
+		 * This bitfield indicates the OEM's desired default Tx
+		 * Spread Spectrum Clocking (SSC) settings for SATA and SAS.
+		 * NOTE: Default SSC Modulation Frequency is 31.5KHz.
+		 */
+		union {
+			struct {
+			/*
+			 * NOTE: Max spread for SATA is +0 / -5000 PPM.
+			 * Down-spreading SSC (only method allowed for SATA):
+			 *  SATA SSC Tx Disabled                    = 0x0
+			 *  SATA SSC Tx at +0 / -1419 PPM Spread    = 0x2
+			 *  SATA SSC Tx at +0 / -2129 PPM Spread    = 0x3
+			 *  SATA SSC Tx at +0 / -4257 PPM Spread    = 0x6
+			 *  SATA SSC Tx at +0 / -4967 PPM Spread    = 0x7
+			 */
+				uint8_t ssc_sata_tx_spread_level:4;
+			/*
+			 * SAS SSC Tx Disabled                     = 0x0
+			 *
+			 * NOTE: Max spread for SAS down-spreading +0 /
+			 *	 -2300 PPM
+			 * Down-spreading SSC:
+			 *  SAS SSC Tx at +0 / -1419 PPM Spread     = 0x2
+			 *  SAS SSC Tx at +0 / -2129 PPM Spread     = 0x3
+			 *
+			 * NOTE: Max spread for SAS center-spreading +2300 /
+			 *	 -2300 PPM
+			 * Center-spreading SSC:
+			 *  SAS SSC Tx at +1064 / -1064 PPM Spread  = 0x3
+			 *  SAS SSC Tx at +2129 / -2129 PPM Spread  = 0x6
+			 */
+				uint8_t ssc_sas_tx_spread_level:3;
+			/*
+			 * NOTE: Refer to the SSC section of the SAS 2.x
+			 * Specification for proper setting of this field.
+			 * For standard SAS Initiator SAS PHY operation it
+			 * should be 0 for Down-spreading.
+			 * SAS SSC Tx spread type:
+			 *  Down-spreading SSC      = 0
+			 *  Center-spreading SSC    = 1
+			 */
+				uint8_t ssc_sas_tx_type:1;
+			};
+			uint8_t do_enable_ssc;
+		};
+		/*
+		 * This field indicates length of the SAS/SATA cable between
+		 * host and device.
+		 * This field is used make relationship between analog
+		 * parameters of the phy in the silicon and length of the cable.
+		 * Supported cable attenuation levels:
+		 * "short"- up to 3m, "medium"-3m to 6m, and "long"- more than
+		 * 6m.
+		 *
+		 * This is bit mask field:
+		 *
+		 * BIT:      (MSB) 7     6     5     4
+		 * ASSIGNMENT:   <phy3><phy2><phy1><phy0>  - Medium cable
+		 *                                           length assignment
+		 * BIT:            3     2     1     0  (LSB)
+		 * ASSIGNMENT:   <phy3><phy2><phy1><phy0>  - Long cable length
+		 *                                           assignment
+		 *
+		 * BITS 7-4 are set when the cable length is assigned to medium
+		 * BITS 3-0 are set when the cable length is assigned to long
+		 *
+		 * The BIT positions are clear when the cable length is
+		 * assigned to short.
+		 *
+		 * Setting the bits for both long and medium cable length is
+		 * undefined.
+		 *
+		 * A value of 0x84 would assign
+		 *    phy3 - medium
+		 *    phy2 - long
+		 *    phy1 - short
+		 *    phy0 - short
+		 */
+		uint8_t cable_selection_mask;
+	} controller;
+
+	struct {
+		uint8_t phy_mask;
+	} ports[SCI_MAX_PORTS];
+
+	struct sci_phy_oem_params {
+		struct {
+			uint32_t high;
+			uint32_t low;
+		} sas_address;
+
+		uint32_t afe_tx_amp_control0;
+		uint32_t afe_tx_amp_control1;
+		uint32_t afe_tx_amp_control2;
+		uint32_t afe_tx_amp_control3;
+	} phys[SCI_MAX_PHYS];
+} __attribute__ ((packed));
+
+struct isci_orom {
+	struct sci_bios_oem_param_block_hdr hdr;
+	struct sci_oem_params ctrl[SCI_MAX_CONTROLLERS];
+} __attribute__ ((packed));
+
+#endif