Initial import

1 files changed, 1532 insertions, 0 deletions

diff --git a/drivers/scsi/pm8001/pm80xx_hwi.h b/drivers/scsi/pm8001/pm80xx_hwi.h
new file mode 100644
index 000000000..9970a3857
--- /dev/null
+++ b/drivers/scsi/pm8001/pm80xx_hwi.h
@@ -0,0 +1,1532 @@
+/*
+ * PMC-Sierra SPCv/ve 8088/8089 SAS/SATA based host adapters driver
+ *
+ * Copyright (c) 2008-2009 USI Co., Ltd.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ *	notice, this list of conditions, and the following disclaimer,
+ *	without modification.
+ * 2. Redistributions in binary form must reproduce at minimum a disclaimer
+ *	substantially similar to the "NO WARRANTY" disclaimer below
+ *	("Disclaimer") and any redistribution must be conditioned upon
+ *	including a substantially similar Disclaimer requirement for further
+ *	binary redistribution.
+ * 3. Neither the names of the above-listed copyright holders nor the names
+ *	of any contributors may be used to endorse or promote products derived
+ *	from this software without specific prior written permission.
+ *
+ * Alternatively, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") version 2 as published by the Free
+ * Software Foundation.
+ *
+ * NO WARRANTY
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
+ * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
+ * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGES.
+ *
+ */
+
+#ifndef _PMC8001_REG_H_
+#define _PMC8001_REG_H_
+
+#include <linux/types.h>
+#include <scsi/libsas.h>
+
+/* for Request Opcode of IOMB */
+#define OPC_INB_ECHO				1	/* 0x000 */
+#define OPC_INB_PHYSTART			4	/* 0x004 */
+#define OPC_INB_PHYSTOP				5	/* 0x005 */
+#define OPC_INB_SSPINIIOSTART			6	/* 0x006 */
+#define OPC_INB_SSPINITMSTART			7	/* 0x007 */
+/* 0x8 RESV IN SPCv */
+#define OPC_INB_RSVD				8	/* 0x008 */
+#define OPC_INB_DEV_HANDLE_ACCEPT		9	/* 0x009 */
+#define OPC_INB_SSPTGTIOSTART			10	/* 0x00A */
+#define OPC_INB_SSPTGTRSPSTART			11	/* 0x00B */
+/* 0xC, 0xD, 0xE removed in SPCv */
+#define OPC_INB_SSP_ABORT			15	/* 0x00F */
+#define OPC_INB_DEREG_DEV_HANDLE		16	/* 0x010 */
+#define OPC_INB_GET_DEV_HANDLE			17	/* 0x011 */
+#define OPC_INB_SMP_REQUEST			18	/* 0x012 */
+/* 0x13 SMP_RESPONSE is removed in SPCv */
+#define OPC_INB_SMP_ABORT			20	/* 0x014 */
+/* 0x16 RESV IN SPCv */
+#define OPC_INB_RSVD1				22	/* 0x016 */
+#define OPC_INB_SATA_HOST_OPSTART		23	/* 0x017 */
+#define OPC_INB_SATA_ABORT			24	/* 0x018 */
+#define OPC_INB_LOCAL_PHY_CONTROL		25	/* 0x019 */
+/* 0x1A RESV IN SPCv */
+#define OPC_INB_RSVD2				26	/* 0x01A */
+#define OPC_INB_FW_FLASH_UPDATE			32	/* 0x020 */
+#define OPC_INB_GPIO				34	/* 0x022 */
+#define OPC_INB_SAS_DIAG_MODE_START_END		35	/* 0x023 */
+#define OPC_INB_SAS_DIAG_EXECUTE		36	/* 0x024 */
+/* 0x25 RESV IN SPCv */
+#define OPC_INB_RSVD3				37	/* 0x025 */
+#define OPC_INB_GET_TIME_STAMP			38	/* 0x026 */
+#define OPC_INB_PORT_CONTROL			39	/* 0x027 */
+#define OPC_INB_GET_NVMD_DATA			40	/* 0x028 */
+#define OPC_INB_SET_NVMD_DATA			41	/* 0x029 */
+#define OPC_INB_SET_DEVICE_STATE		42	/* 0x02A */
+#define OPC_INB_GET_DEVICE_STATE		43	/* 0x02B */
+#define OPC_INB_SET_DEV_INFO			44	/* 0x02C */
+/* 0x2D RESV IN SPCv */
+#define OPC_INB_RSVD4				45	/* 0x02D */
+#define OPC_INB_SGPIO_REGISTER			46	/* 0x02E */
+#define OPC_INB_PCIE_DIAG_EXEC			47	/* 0x02F */
+#define OPC_INB_SET_CONTROLLER_CONFIG		48	/* 0x030 */
+#define OPC_INB_GET_CONTROLLER_CONFIG		49	/* 0x031 */
+#define OPC_INB_REG_DEV				50	/* 0x032 */
+#define OPC_INB_SAS_HW_EVENT_ACK		51	/* 0x033 */
+#define OPC_INB_GET_DEVICE_INFO			52	/* 0x034 */
+#define OPC_INB_GET_PHY_PROFILE			53	/* 0x035 */
+#define OPC_INB_FLASH_OP_EXT			54	/* 0x036 */
+#define OPC_INB_SET_PHY_PROFILE			55	/* 0x037 */
+#define OPC_INB_KEK_MANAGEMENT			256	/* 0x100 */
+#define OPC_INB_DEK_MANAGEMENT			257	/* 0x101 */
+#define OPC_INB_SSP_INI_DIF_ENC_IO		258	/* 0x102 */
+#define OPC_INB_SATA_DIF_ENC_IO			259	/* 0x103 */
+
+/* for Response Opcode of IOMB */
+#define OPC_OUB_ECHO					1	/* 0x001 */
+#define OPC_OUB_RSVD					4	/* 0x004 */
+#define OPC_OUB_SSP_COMP				5	/* 0x005 */
+#define OPC_OUB_SMP_COMP				6	/* 0x006 */
+#define OPC_OUB_LOCAL_PHY_CNTRL				7	/* 0x007 */
+#define OPC_OUB_RSVD1					10	/* 0x00A */
+#define OPC_OUB_DEREG_DEV				11	/* 0x00B */
+#define OPC_OUB_GET_DEV_HANDLE				12	/* 0x00C */
+#define OPC_OUB_SATA_COMP				13	/* 0x00D */
+#define OPC_OUB_SATA_EVENT				14	/* 0x00E */
+#define OPC_OUB_SSP_EVENT				15	/* 0x00F */
+#define OPC_OUB_RSVD2					16	/* 0x010 */
+/* 0x11 - SMP_RECEIVED Notification removed in SPCv*/
+#define OPC_OUB_SSP_RECV_EVENT				18	/* 0x012 */
+#define OPC_OUB_RSVD3					19	/* 0x013 */
+#define OPC_OUB_FW_FLASH_UPDATE				20	/* 0x014 */
+#define OPC_OUB_GPIO_RESPONSE				22	/* 0x016 */
+#define OPC_OUB_GPIO_EVENT				23	/* 0x017 */
+#define OPC_OUB_GENERAL_EVENT				24	/* 0x018 */
+#define OPC_OUB_SSP_ABORT_RSP				26	/* 0x01A */
+#define OPC_OUB_SATA_ABORT_RSP				27	/* 0x01B */
+#define OPC_OUB_SAS_DIAG_MODE_START_END			28	/* 0x01C */
+#define OPC_OUB_SAS_DIAG_EXECUTE			29	/* 0x01D */
+#define OPC_OUB_GET_TIME_STAMP				30	/* 0x01E */
+#define OPC_OUB_RSVD4					31	/* 0x01F */
+#define OPC_OUB_PORT_CONTROL				32	/* 0x020 */
+#define OPC_OUB_SKIP_ENTRY				33	/* 0x021 */
+#define OPC_OUB_SMP_ABORT_RSP				34	/* 0x022 */
+#define OPC_OUB_GET_NVMD_DATA				35	/* 0x023 */
+#define OPC_OUB_SET_NVMD_DATA				36	/* 0x024 */
+#define OPC_OUB_DEVICE_HANDLE_REMOVAL			37	/* 0x025 */
+#define OPC_OUB_SET_DEVICE_STATE			38	/* 0x026 */
+#define OPC_OUB_GET_DEVICE_STATE			39	/* 0x027 */
+#define OPC_OUB_SET_DEV_INFO				40	/* 0x028 */
+#define OPC_OUB_RSVD5					41	/* 0x029 */
+#define OPC_OUB_HW_EVENT				1792	/* 0x700 */
+#define OPC_OUB_DEV_HANDLE_ARRIV			1824	/* 0x720 */
+#define OPC_OUB_THERM_HW_EVENT				1840	/* 0x730 */
+#define OPC_OUB_SGPIO_RESP				2094	/* 0x82E */
+#define OPC_OUB_PCIE_DIAG_EXECUTE			2095	/* 0x82F */
+#define OPC_OUB_DEV_REGIST				2098	/* 0x832 */
+#define OPC_OUB_SAS_HW_EVENT_ACK			2099	/* 0x833 */
+#define OPC_OUB_GET_DEVICE_INFO				2100	/* 0x834 */
+/* spcv specific commands */
+#define OPC_OUB_PHY_START_RESP				2052	/* 0x804 */
+#define OPC_OUB_PHY_STOP_RESP				2053	/* 0x805 */
+#define OPC_OUB_SET_CONTROLLER_CONFIG			2096	/* 0x830 */
+#define OPC_OUB_GET_CONTROLLER_CONFIG			2097	/* 0x831 */
+#define OPC_OUB_GET_PHY_PROFILE				2101	/* 0x835 */
+#define OPC_OUB_FLASH_OP_EXT				2102	/* 0x836 */
+#define OPC_OUB_SET_PHY_PROFILE				2103	/* 0x837 */
+#define OPC_OUB_KEK_MANAGEMENT_RESP			2304	/* 0x900 */
+#define OPC_OUB_DEK_MANAGEMENT_RESP			2305	/* 0x901 */
+#define OPC_OUB_SSP_COALESCED_COMP_RESP			2306	/* 0x902 */
+
+/* for phy start*/
+#define SSC_DISABLE_15			(0x01 << 16)
+#define SSC_DISABLE_30			(0x02 << 16)
+#define SSC_DISABLE_60			(0x04 << 16)
+#define SAS_ASE				(0x01 << 15)
+#define SPINHOLD_DISABLE		(0x00 << 14)
+#define SPINHOLD_ENABLE			(0x01 << 14)
+#define LINKMODE_SAS			(0x01 << 12)
+#define LINKMODE_DSATA			(0x02 << 12)
+#define LINKMODE_AUTO			(0x03 << 12)
+#define LINKRATE_15			(0x01 << 8)
+#define LINKRATE_30			(0x02 << 8)
+#define LINKRATE_60			(0x06 << 8)
+#define LINKRATE_120			(0x08 << 8)
+
+/* phy_profile */
+#define SAS_PHY_ANALOG_SETTINGS_PAGE	0x04
+#define PHY_DWORD_LENGTH		0xC
+
+/* Thermal related */
+#define	THERMAL_ENABLE			0x1
+#define	THERMAL_LOG_ENABLE		0x1
+#define THERMAL_OP_CODE			0x6
+#define LTEMPHIL			 70
+#define RTEMPHIL			100
+
+/* Encryption info */
+#define SCRATCH_PAD3_ENC_DISABLED	0x00000000
+#define SCRATCH_PAD3_ENC_DIS_ERR	0x00000001
+#define SCRATCH_PAD3_ENC_ENA_ERR	0x00000002
+#define SCRATCH_PAD3_ENC_READY		0x00000003
+#define SCRATCH_PAD3_ENC_MASK		SCRATCH_PAD3_ENC_READY
+
+#define SCRATCH_PAD3_XTS_ENABLED		(1 << 14)
+#define SCRATCH_PAD3_SMA_ENABLED		(1 << 4)
+#define SCRATCH_PAD3_SMB_ENABLED		(1 << 5)
+#define SCRATCH_PAD3_SMF_ENABLED		0
+#define SCRATCH_PAD3_SM_MASK			0x000000F0
+#define SCRATCH_PAD3_ERR_CODE			0x00FF0000
+
+#define SEC_MODE_SMF				0x0
+#define SEC_MODE_SMA				0x100
+#define SEC_MODE_SMB				0x200
+#define CIPHER_MODE_ECB				0x00000001
+#define CIPHER_MODE_XTS				0x00000002
+#define KEK_MGMT_SUBOP_KEYCARDUPDATE		0x4
+
+/* SAS protocol timer configuration page */
+#define SAS_PROTOCOL_TIMER_CONFIG_PAGE  0x04
+#define STP_MCT_TMO                     32
+#define SSP_MCT_TMO                     32
+#define SAS_MAX_OPEN_TIME				5
+#define SMP_MAX_CONN_TIMER              0xFF
+#define STP_FRM_TIMER                   0
+#define STP_IDLE_TIME                   5 /* 5 us; controller default */
+#define SAS_MFD                         0
+#define SAS_OPNRJT_RTRY_INTVL           2
+#define SAS_DOPNRJT_RTRY_TMO            128
+#define SAS_COPNRJT_RTRY_TMO            128
+
+/* for phy state */
+#define PHY_STATE_LINK_UP_SPCV		0x2
+/*
+  Making ORR bigger than IT NEXUS LOSS which is 2000000us = 2 second.
+  Assuming a bigger value 3 second, 3000000/128 = 23437.5 where 128
+  is DOPNRJT_RTRY_TMO
+*/
+#define SAS_DOPNRJT_RTRY_THR            23438
+#define SAS_COPNRJT_RTRY_THR            23438
+#define SAS_MAX_AIP                     0x200000
+#define IT_NEXUS_TIMEOUT       0x7D0
+#define PORT_RECOVERY_TIMEOUT  ((IT_NEXUS_TIMEOUT/100) + 30)
+
+struct mpi_msg_hdr {
+	__le32	header;	/* Bits [11:0] - Message operation code */
+	/* Bits [15:12] - Message Category */
+	/* Bits [21:16] - Outboundqueue ID for the
+	operation completion message */
+	/* Bits [23:22] - Reserved */
+	/* Bits [28:24] - Buffer Count, indicates how
+	many buffer are allocated for the massage */
+	/* Bits [30:29] - Reserved */
+	/* Bits [31] - Message Valid bit */
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of PHY Start Command
+ * use to describe enable the phy (128 bytes)
+ */
+struct phy_start_req {
+	__le32	tag;
+	__le32	ase_sh_lm_slr_phyid;
+	struct sas_identify_frame sas_identify; /* 28 Bytes */
+	__le32 spasti;
+	u32	reserved[21];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of PHY Start Command
+ * use to disable the phy (128 bytes)
+ */
+struct phy_stop_req {
+	__le32	tag;
+	__le32	phy_id;
+	u32	reserved[29];
+} __attribute__((packed, aligned(4)));
+
+/* set device bits fis - device to host */
+struct set_dev_bits_fis {
+	u8	fis_type;	/* 0xA1*/
+	u8	n_i_pmport;
+	/* b7 : n Bit. Notification bit. If set device needs attention. */
+	/* b6 : i Bit. Interrupt Bit */
+	/* b5-b4: reserved2 */
+	/* b3-b0: PM Port */
+	u8	status;
+	u8	error;
+	u32	_r_a;
+} __attribute__ ((packed));
+/* PIO setup FIS - device to host */
+struct pio_setup_fis {
+	u8	fis_type;	/* 0x5f */
+	u8	i_d_pmPort;
+	/* b7 : reserved */
+	/* b6 : i bit. Interrupt bit */
+	/* b5 : d bit. data transfer direction. set to 1 for device to host
+	xfer */
+	/* b4 : reserved */
+	/* b3-b0: PM Port */
+	u8	status;
+	u8	error;
+	u8	lbal;
+	u8	lbam;
+	u8	lbah;
+	u8	device;
+	u8	lbal_exp;
+	u8	lbam_exp;
+	u8	lbah_exp;
+	u8	_r_a;
+	u8	sector_count;
+	u8	sector_count_exp;
+	u8	_r_b;
+	u8	e_status;
+	u8	_r_c[2];
+	u8	transfer_count;
+} __attribute__ ((packed));
+
+/*
+ * brief the data structure of SATA Completion Response
+ * use to describe the sata task response (64 bytes)
+ */
+struct sata_completion_resp {
+	__le32	tag;
+	__le32	status;
+	__le32	param;
+	u32	sata_resp[12];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of SAS HW Event Notification
+ * use to alert the host about the hardware event(64 bytes)
+ */
+/* updated outbound struct for spcv */
+
+struct hw_event_resp {
+	__le32	lr_status_evt_portid;
+	__le32	evt_param;
+	__le32	phyid_npip_portstate;
+	struct sas_identify_frame	sas_identify;
+	struct dev_to_host_fis	sata_fis;
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure for thermal event notification
+ */
+
+struct thermal_hw_event {
+	__le32	thermal_event;
+	__le32	rht_lht;
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of REGISTER DEVICE Command
+ * use to describe MPI REGISTER DEVICE Command (64 bytes)
+ */
+
+struct reg_dev_req {
+	__le32	tag;
+	__le32	phyid_portid;
+	__le32	dtype_dlr_mcn_ir_retry;
+	__le32	firstburstsize_ITNexustimeout;
+	u8	sas_addr[SAS_ADDR_SIZE];
+	__le32	upper_device_id;
+	u32	reserved[24];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of DEREGISTER DEVICE Command
+ * use to request spc to remove all internal resources associated
+ * with the device id (64 bytes)
+ */
+
+struct dereg_dev_req {
+	__le32	tag;
+	__le32	device_id;
+	u32	reserved[29];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of DEVICE_REGISTRATION Response
+ * use to notify the completion of the device registration (64 bytes)
+ */
+struct dev_reg_resp {
+	__le32	tag;
+	__le32	status;
+	__le32	device_id;
+	u32	reserved[12];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of Local PHY Control Command
+ * use to issue PHY CONTROL to local phy (64 bytes)
+ */
+struct local_phy_ctl_req {
+	__le32	tag;
+	__le32	phyop_phyid;
+	u32	reserved1[29];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of Local Phy Control Response
+ * use to describe MPI Local Phy Control Response (64 bytes)
+ */
+ struct local_phy_ctl_resp {
+	__le32	tag;
+	__le32	phyop_phyid;
+	__le32	status;
+	u32	reserved[12];
+} __attribute__((packed, aligned(4)));
+
+#define OP_BITS 0x0000FF00
+#define ID_BITS 0x000000FF
+
+/*
+ * brief the data structure of PORT Control Command
+ * use to control port properties (64 bytes)
+ */
+
+struct port_ctl_req {
+	__le32	tag;
+	__le32	portop_portid;
+	__le32	param0;
+	__le32	param1;
+	u32	reserved1[27];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of HW Event Ack Command
+ * use to acknowledge receive HW event (64 bytes)
+ */
+struct hw_event_ack_req {
+	__le32	tag;
+	__le32	phyid_sea_portid;
+	__le32	param0;
+	__le32	param1;
+	u32	reserved1[27];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of PHY_START Response Command
+ * indicates the completion of PHY_START command (64 bytes)
+ */
+struct phy_start_resp {
+	__le32	tag;
+	__le32	status;
+	__le32	phyid;
+	u32	reserved[12];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of PHY_STOP Response Command
+ * indicates the completion of PHY_STOP command (64 bytes)
+ */
+struct phy_stop_resp {
+	__le32	tag;
+	__le32	status;
+	__le32	phyid;
+	u32	reserved[12];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of SSP Completion Response
+ * use to indicate a SSP Completion (n bytes)
+ */
+struct ssp_completion_resp {
+	__le32	tag;
+	__le32	status;
+	__le32	param;
+	__le32	ssptag_rescv_rescpad;
+	struct ssp_response_iu ssp_resp_iu;
+	__le32	residual_count;
+} __attribute__((packed, aligned(4)));
+
+#define SSP_RESCV_BIT	0x00010000
+
+/*
+ * brief the data structure of SATA EVNET response
+ * use to indicate a SATA Completion (64 bytes)
+ */
+struct sata_event_resp {
+	__le32 tag;
+	__le32 event;
+	__le32 port_id;
+	__le32 device_id;
+	u32 reserved;
+	__le32 event_param0;
+	__le32 event_param1;
+	__le32 sata_addr_h32;
+	__le32 sata_addr_l32;
+	__le32 e_udt1_udt0_crc;
+	__le32 e_udt5_udt4_udt3_udt2;
+	__le32 a_udt1_udt0_crc;
+	__le32 a_udt5_udt4_udt3_udt2;
+	__le32 hwdevid_diferr;
+	__le32 err_framelen_byteoffset;
+	__le32 err_dataframe;
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of SSP EVNET esponse
+ * use to indicate a SSP Completion (64 bytes)
+ */
+struct ssp_event_resp {
+	__le32 tag;
+	__le32 event;
+	__le32 port_id;
+	__le32 device_id;
+	__le32 ssp_tag;
+	__le32 event_param0;
+	__le32 event_param1;
+	__le32 sas_addr_h32;
+	__le32 sas_addr_l32;
+	__le32 e_udt1_udt0_crc;
+	__le32 e_udt5_udt4_udt3_udt2;
+	__le32 a_udt1_udt0_crc;
+	__le32 a_udt5_udt4_udt3_udt2;
+	__le32 hwdevid_diferr;
+	__le32 err_framelen_byteoffset;
+	__le32 err_dataframe;
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of General Event Notification Response
+ * use to describe MPI General Event Notification Response (64 bytes)
+ */
+struct general_event_resp {
+	__le32	status;
+	__le32	inb_IOMB_payload[14];
+} __attribute__((packed, aligned(4)));
+
+#define GENERAL_EVENT_PAYLOAD	14
+#define OPCODE_BITS	0x00000fff
+
+/*
+ * brief the data structure of SMP Request Command
+ * use to describe MPI SMP REQUEST Command (64 bytes)
+ */
+struct smp_req {
+	__le32	tag;
+	__le32	device_id;
+	__le32	len_ip_ir;
+	/* Bits [0] - Indirect response */
+	/* Bits [1] - Indirect Payload */
+	/* Bits [15:2] - Reserved */
+	/* Bits [23:16] - direct payload Len */
+	/* Bits [31:24] - Reserved */
+	u8	smp_req16[16];
+	union {
+		u8	smp_req[32];
+		struct {
+			__le64 long_req_addr;/* sg dma address, LE */
+			__le32 long_req_size;/* LE */
+			u32	_r_a;
+			__le64 long_resp_addr;/* sg dma address, LE */
+			__le32 long_resp_size;/* LE */
+			u32	_r_b;
+			} long_smp_req;/* sequencer extension */
+	};
+	__le32	rsvd[16];
+} __attribute__((packed, aligned(4)));
+/*
+ * brief the data structure of SMP Completion Response
+ * use to describe MPI SMP Completion Response (64 bytes)
+ */
+struct smp_completion_resp {
+	__le32	tag;
+	__le32	status;
+	__le32	param;
+	u8	_r_a[252];
+} __attribute__((packed, aligned(4)));
+
+/*
+ *brief the data structure of SSP SMP SATA Abort Command
+ * use to describe MPI SSP SMP & SATA Abort Command (64 bytes)
+ */
+struct task_abort_req {
+	__le32	tag;
+	__le32	device_id;
+	__le32	tag_to_abort;
+	__le32	abort_all;
+	u32	reserved[27];
+} __attribute__((packed, aligned(4)));
+
+/* These flags used for SSP SMP & SATA Abort */
+#define ABORT_MASK		0x3
+#define ABORT_SINGLE		0x0
+#define ABORT_ALL		0x1
+
+/**
+ * brief the data structure of SSP SATA SMP Abort Response
+ * use to describe SSP SMP & SATA Abort Response ( 64 bytes)
+ */
+struct task_abort_resp {
+	__le32	tag;
+	__le32	status;
+	__le32	scp;
+	u32	reserved[12];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SAS Diagnostic Start/End Command
+ * use to describe MPI SAS Diagnostic Start/End Command (64 bytes)
+ */
+struct sas_diag_start_end_req {
+	__le32	tag;
+	__le32	operation_phyid;
+	u32	reserved[29];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SAS Diagnostic Execute Command
+ * use to describe MPI SAS Diagnostic Execute Command (64 bytes)
+ */
+struct sas_diag_execute_req {
+	__le32	tag;
+	__le32	cmdtype_cmddesc_phyid;
+	__le32	pat1_pat2;
+	__le32	threshold;
+	__le32	codepat_errmsk;
+	__le32	pmon;
+	__le32	pERF1CTL;
+	u32	reserved[24];
+} __attribute__((packed, aligned(4)));
+
+#define SAS_DIAG_PARAM_BYTES 24
+
+/*
+ * brief the data structure of Set Device State Command
+ * use to describe MPI Set Device State Command (64 bytes)
+ */
+struct set_dev_state_req {
+	__le32	tag;
+	__le32	device_id;
+	__le32	nds;
+	u32	reserved[28];
+} __attribute__((packed, aligned(4)));
+
+/*
+ * brief the data structure of SATA Start Command
+ * use to describe MPI SATA IO Start Command (64 bytes)
+ * Note: This structure is common for normal / encryption I/O
+ */
+
+struct sata_start_req {
+	__le32	tag;
+	__le32	device_id;
+	__le32	data_len;
+	__le32	ncqtag_atap_dir_m_dad;
+	struct host_to_dev_fis	sata_fis;
+	u32	reserved1;
+	u32	reserved2;	/* dword 11. rsvd for normal I/O. */
+				/* EPLE Descl for enc I/O */
+	u32	addr_low;	/* dword 12. rsvd for enc I/O */
+	u32	addr_high;	/* dword 13. reserved for enc I/O */
+	__le32	len;		/* dword 14: length for normal I/O. */
+				/* EPLE Desch for enc I/O */
+	__le32	esgl;		/* dword 15. rsvd for enc I/O */
+	__le32	atapi_scsi_cdb[4];	/* dword 16-19. rsvd for enc I/O */
+	/* The below fields are reserved for normal I/O */
+	__le32	key_index_mode;	/* dword 20 */
+	__le32	sector_cnt_enss;/* dword 21 */
+	__le32	keytagl;	/* dword 22 */
+	__le32	keytagh;	/* dword 23 */
+	__le32	twk_val0;	/* dword 24 */
+	__le32	twk_val1;	/* dword 25 */
+	__le32	twk_val2;	/* dword 26 */
+	__le32	twk_val3;	/* dword 27 */
+	__le32	enc_addr_low;	/* dword 28. Encryption SGL address high */
+	__le32	enc_addr_high;	/* dword 29. Encryption SGL address low */
+	__le32	enc_len;	/* dword 30. Encryption length */
+	__le32	enc_esgl;	/* dword 31. Encryption esgl bit */
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SSP INI TM Start Command
+ * use to describe MPI SSP INI TM Start Command (64 bytes)
+ */
+struct ssp_ini_tm_start_req {
+	__le32	tag;
+	__le32	device_id;
+	__le32	relate_tag;
+	__le32	tmf;
+	u8	lun[8];
+	__le32	ds_ads_m;
+	u32	reserved[24];
+} __attribute__((packed, aligned(4)));
+
+struct ssp_info_unit {
+	u8	lun[8];/* SCSI Logical Unit Number */
+	u8	reserved1;/* reserved */
+	u8	efb_prio_attr;
+	/* B7 : enabledFirstBurst */
+	/* B6-3 : taskPriority */
+	/* B2-0 : taskAttribute */
+	u8	reserved2;	/* reserved */
+	u8	additional_cdb_len;
+	/* B7-2 : additional_cdb_len */
+	/* B1-0 : reserved */
+	u8	cdb[16];/* The SCSI CDB up to 16 bytes length */
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SSP INI IO Start Command
+ * use to describe MPI SSP INI IO Start Command (64 bytes)
+ * Note: This structure is common for normal / encryption I/O
+ */
+struct ssp_ini_io_start_req {
+	__le32	tag;
+	__le32	device_id;
+	__le32	data_len;
+	__le32	dad_dir_m_tlr;
+	struct ssp_info_unit	ssp_iu;
+	__le32	addr_low;	/* dword 12: sgl low for normal I/O. */
+				/* epl_descl for encryption I/O */
+	__le32	addr_high;	/* dword 13: sgl hi for normal I/O */
+				/* dpl_descl for encryption I/O */
+	__le32	len;		/* dword 14: len for normal I/O. */
+				/* edpl_desch for encryption I/O */
+	__le32	esgl;		/* dword 15: ESGL bit for normal I/O. */
+				/* user defined tag mask for enc I/O */
+	/* The below fields are reserved for normal I/O */
+	u8	udt[12];	/* dword 16-18 */
+	__le32	sectcnt_ios;	/* dword 19 */
+	__le32	key_cmode;	/* dword 20 */
+	__le32	ks_enss;	/* dword 21 */
+	__le32	keytagl;	/* dword 22 */
+	__le32	keytagh;	/* dword 23 */
+	__le32	twk_val0;	/* dword 24 */
+	__le32	twk_val1;	/* dword 25 */
+	__le32	twk_val2;	/* dword 26 */
+	__le32	twk_val3;	/* dword 27 */
+	__le32	enc_addr_low;	/* dword 28: Encryption sgl addr low */
+	__le32	enc_addr_high;	/* dword 29: Encryption sgl addr hi */
+	__le32	enc_len;	/* dword 30: Encryption length */
+	__le32	enc_esgl;	/* dword 31: ESGL bit for encryption */
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for SSP_INI_DIF_ENC_IO COMMAND
+ * use to initiate SSP I/O operation with optional DIF/ENC
+ */
+struct ssp_dif_enc_io_req {
+	__le32	tag;
+	__le32	device_id;
+	__le32	data_len;
+	__le32	dirMTlr;
+	__le32	sspiu0;
+	__le32	sspiu1;
+	__le32	sspiu2;
+	__le32	sspiu3;
+	__le32	sspiu4;
+	__le32	sspiu5;
+	__le32	sspiu6;
+	__le32	epl_des;
+	__le32	dpl_desl_ndplr;
+	__le32	dpl_desh;
+	__le32	uum_uuv_bss_difbits;
+	u8	udt[12];
+	__le32	sectcnt_ios;
+	__le32	key_cmode;
+	__le32	ks_enss;
+	__le32	keytagl;
+	__le32	keytagh;
+	__le32	twk_val0;
+	__le32	twk_val1;
+	__le32	twk_val2;
+	__le32	twk_val3;
+	__le32	addr_low;
+	__le32	addr_high;
+	__le32	len;
+	__le32	esgl;
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of Firmware download
+ * use to describe MPI FW DOWNLOAD Command (64 bytes)
+ */
+struct fw_flash_Update_req {
+	__le32	tag;
+	__le32	cur_image_offset;
+	__le32	cur_image_len;
+	__le32	total_image_len;
+	u32	reserved0[7];
+	__le32	sgl_addr_lo;
+	__le32	sgl_addr_hi;
+	__le32	len;
+	__le32	ext_reserved;
+	u32	reserved1[16];
+} __attribute__((packed, aligned(4)));
+
+#define FWFLASH_IOMB_RESERVED_LEN 0x07
+/**
+ * brief the data structure of FW_FLASH_UPDATE Response
+ * use to describe MPI FW_FLASH_UPDATE Response (64 bytes)
+ *
+ */
+ struct fw_flash_Update_resp {
+	__le32	tag;
+	__le32	status;
+	u32	reserved[13];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of Get NVM Data Command
+ * use to get data from NVM in HBA(64 bytes)
+ */
+struct get_nvm_data_req {
+	__le32	tag;
+	__le32	len_ir_vpdd;
+	__le32	vpd_offset;
+	u32	reserved[8];
+	__le32	resp_addr_lo;
+	__le32	resp_addr_hi;
+	__le32	resp_len;
+	u32	reserved1[17];
+} __attribute__((packed, aligned(4)));
+
+struct set_nvm_data_req {
+	__le32	tag;
+	__le32	len_ir_vpdd;
+	__le32	vpd_offset;
+	u32	reserved[8];
+	__le32	resp_addr_lo;
+	__le32	resp_addr_hi;
+	__le32	resp_len;
+	u32	reserved1[17];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for SET CONTROLLER CONFIG COMMAND
+ * use to modify controller configuration
+ */
+struct set_ctrl_cfg_req {
+	__le32	tag;
+	__le32	cfg_pg[14];
+	u32	reserved[16];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for GET CONTROLLER CONFIG COMMAND
+ * use to get controller configuration page
+ */
+struct get_ctrl_cfg_req {
+	__le32	tag;
+	__le32	pgcd;
+	__le32	int_vec;
+	u32	reserved[28];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for KEK_MANAGEMENT COMMAND
+ * use for KEK management
+ */
+struct kek_mgmt_req {
+	__le32	tag;
+	__le32	new_curidx_ksop;
+	u32	reserved;
+	__le32	kblob[12];
+	u32	reserved1[16];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for DEK_MANAGEMENT COMMAND
+ * use for DEK management
+ */
+struct dek_mgmt_req {
+	__le32	tag;
+	__le32	kidx_dsop;
+	__le32	dekidx;
+	__le32	addr_l;
+	__le32	addr_h;
+	__le32	nent;
+	__le32	dbf_tblsize;
+	u32	reserved[24];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for SET PHY PROFILE COMMAND
+ * use to retrive phy specific information
+ */
+struct set_phy_profile_req {
+	__le32	tag;
+	__le32	ppc_phyid;
+	u32	reserved[29];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for GET PHY PROFILE COMMAND
+ * use to retrive phy specific information
+ */
+struct get_phy_profile_req {
+	__le32	tag;
+	__le32	ppc_phyid;
+	__le32	profile[29];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure for EXT FLASH PARTITION
+ * use to manage ext flash partition
+ */
+struct ext_flash_partition_req {
+	__le32	tag;
+	__le32	cmd;
+	__le32	offset;
+	__le32	len;
+	u32	reserved[7];
+	__le32	addr_low;
+	__le32	addr_high;
+	__le32	len1;
+	__le32	ext;
+	u32	reserved1[16];
+} __attribute__((packed, aligned(4)));
+
+#define TWI_DEVICE	0x0
+#define C_SEEPROM	0x1
+#define VPD_FLASH	0x4
+#define AAP1_RDUMP	0x5
+#define IOP_RDUMP	0x6
+#define EXPAN_ROM	0x7
+
+#define IPMode		0x80000000
+#define NVMD_TYPE	0x0000000F
+#define NVMD_STAT	0x0000FFFF
+#define NVMD_LEN	0xFF000000
+/**
+ * brief the data structure of Get NVMD Data Response
+ * use to describe MPI Get NVMD Data Response (64 bytes)
+ */
+struct get_nvm_data_resp {
+	__le32		tag;
+	__le32		ir_tda_bn_dps_das_nvm;
+	__le32		dlen_status;
+	__le32		nvm_data[12];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SAS Diagnostic Start/End Response
+ * use to describe MPI SAS Diagnostic Start/End Response (64 bytes)
+ *
+ */
+struct sas_diag_start_end_resp {
+	__le32		tag;
+	__le32		status;
+	u32		reserved[13];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of SAS Diagnostic Execute Response
+ * use to describe MPI SAS Diagnostic Execute Response (64 bytes)
+ *
+ */
+struct sas_diag_execute_resp {
+	__le32		tag;
+	__le32		cmdtype_cmddesc_phyid;
+	__le32		Status;
+	__le32		ReportData;
+	u32		reserved[11];
+} __attribute__((packed, aligned(4)));
+
+/**
+ * brief the data structure of Set Device State Response
+ * use to describe MPI Set Device State Response (64 bytes)
+ *
+ */
+struct set_dev_state_resp {
+	__le32		tag;
+	__le32		status;
+	__le32		device_id;
+	__le32		pds_nds;
+	u32		reserved[11];
+} __attribute__((packed, aligned(4)));
+
+/* new outbound structure for spcv - begins */
+/**
+ * brief the data structure for SET CONTROLLER CONFIG COMMAND
+ * use to modify controller configuration
+ */
+struct set_ctrl_cfg_resp {
+	__le32 tag;
+	__le32 status;
+	__le32 err_qlfr_pgcd;
+	u32 reserved[12];
+} __attribute__((packed, aligned(4)));
+
+struct get_ctrl_cfg_resp {
+	__le32 tag;
+	__le32 status;
+	__le32 err_qlfr;
+	__le32 confg_page[12];
+} __attribute__((packed, aligned(4)));
+
+struct kek_mgmt_resp {
+	__le32 tag;
+	__le32 status;
+	__le32 kidx_new_curr_ksop;
+	__le32 err_qlfr;
+	u32 reserved[11];
+} __attribute__((packed, aligned(4)));
+
+struct dek_mgmt_resp {
+	__le32 tag;
+	__le32 status;
+	__le32 kekidx_tbls_dsop;
+	__le32 dekidx;
+	__le32 err_qlfr;
+	u32 reserved[10];
+} __attribute__((packed, aligned(4)));
+
+struct get_phy_profile_resp {
+	__le32 tag;
+	__le32 status;
+	__le32 ppc_phyid;
+	__le32 ppc_specific_rsp[12];
+} __attribute__((packed, aligned(4)));
+
+struct flash_op_ext_resp {
+	__le32 tag;
+	__le32 cmd;
+	__le32 status;
+	__le32 epart_size;
+	__le32 epart_sect_size;
+	u32 reserved[10];
+} __attribute__((packed, aligned(4)));
+
+struct set_phy_profile_resp {
+	__le32 tag;
+	__le32 status;
+	__le32 ppc_phyid;
+	__le32 ppc_specific_rsp[12];
+} __attribute__((packed, aligned(4)));
+
+struct ssp_coalesced_comp_resp {
+	__le32 coal_cnt;
+	__le32 tag0;
+	__le32 ssp_tag0;
+	__le32 tag1;
+	__le32 ssp_tag1;
+	__le32 add_tag_ssp_tag[10];
+} __attribute__((packed, aligned(4)));
+
+/* new outbound structure for spcv - ends */
+
+/* brief data structure for SAS protocol timer configuration page.
+ *
+ */
+struct SASProtocolTimerConfig {
+	__le32 pageCode;			/* 0 */
+	__le32 MST_MSI;				/* 1 */
+	__le32 STP_SSP_MCT_TMO;			/* 2 */
+	__le32 STP_FRM_TMO;			/* 3 */
+	__le32 STP_IDLE_TMO;			/* 4 */
+	__le32 OPNRJT_RTRY_INTVL;		/* 5 */
+	__le32 Data_Cmd_OPNRJT_RTRY_TMO;	/* 6 */
+	__le32 Data_Cmd_OPNRJT_RTRY_THR;	/* 7 */
+	__le32 MAX_AIP;				/* 8 */
+} __attribute__((packed, aligned(4)));
+
+typedef struct SASProtocolTimerConfig SASProtocolTimerConfig_t;
+
+#define NDS_BITS 0x0F
+#define PDS_BITS 0xF0
+
+/*
+ * HW Events type
+ */
+
+#define HW_EVENT_RESET_START			0x01
+#define HW_EVENT_CHIP_RESET_COMPLETE		0x02
+#define HW_EVENT_PHY_STOP_STATUS		0x03
+#define HW_EVENT_SAS_PHY_UP			0x04
+#define HW_EVENT_SATA_PHY_UP			0x05
+#define HW_EVENT_SATA_SPINUP_HOLD		0x06
+#define HW_EVENT_PHY_DOWN			0x07
+#define HW_EVENT_PORT_INVALID			0x08
+#define HW_EVENT_BROADCAST_CHANGE		0x09
+#define HW_EVENT_PHY_ERROR			0x0A
+#define HW_EVENT_BROADCAST_SES			0x0B
+#define HW_EVENT_INBOUND_CRC_ERROR		0x0C
+#define HW_EVENT_HARD_RESET_RECEIVED		0x0D
+#define HW_EVENT_MALFUNCTION			0x0E
+#define HW_EVENT_ID_FRAME_TIMEOUT		0x0F
+#define HW_EVENT_BROADCAST_EXP			0x10
+#define HW_EVENT_PHY_START_STATUS		0x11
+#define HW_EVENT_LINK_ERR_INVALID_DWORD		0x12
+#define HW_EVENT_LINK_ERR_DISPARITY_ERROR	0x13
+#define HW_EVENT_LINK_ERR_CODE_VIOLATION	0x14
+#define HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH	0x15
+#define HW_EVENT_LINK_ERR_PHY_RESET_FAILED	0x16
+#define HW_EVENT_PORT_RECOVERY_TIMER_TMO	0x17
+#define HW_EVENT_PORT_RECOVER			0x18
+#define HW_EVENT_PORT_RESET_TIMER_TMO		0x19
+#define HW_EVENT_PORT_RESET_COMPLETE		0x20
+#define EVENT_BROADCAST_ASYNCH_EVENT		0x21
+
+/* port state */
+#define PORT_NOT_ESTABLISHED			0x00
+#define PORT_VALID				0x01
+#define PORT_LOSTCOMM				0x02
+#define PORT_IN_RESET				0x04
+#define PORT_3RD_PARTY_RESET			0x07
+#define PORT_INVALID				0x08
+
+/*
+ * SSP/SMP/SATA IO Completion Status values
+ */
+
+#define IO_SUCCESS				0x00
+#define IO_ABORTED				0x01
+#define IO_OVERFLOW				0x02
+#define IO_UNDERFLOW				0x03
+#define IO_FAILED				0x04
+#define IO_ABORT_RESET				0x05
+#define IO_NOT_VALID				0x06
+#define IO_NO_DEVICE				0x07
+#define IO_ILLEGAL_PARAMETER			0x08
+#define IO_LINK_FAILURE				0x09
+#define IO_PROG_ERROR				0x0A
+
+#define IO_EDC_IN_ERROR				0x0B
+#define IO_EDC_OUT_ERROR			0x0C
+#define IO_ERROR_HW_TIMEOUT			0x0D
+#define IO_XFER_ERROR_BREAK			0x0E
+#define IO_XFER_ERROR_PHY_NOT_READY		0x0F
+#define IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED	0x10
+#define IO_OPEN_CNX_ERROR_ZONE_VIOLATION		0x11
+#define IO_OPEN_CNX_ERROR_BREAK				0x12
+#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS			0x13
+#define IO_OPEN_CNX_ERROR_BAD_DESTINATION		0x14
+#define IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED	0x15
+#define IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY		0x16
+#define IO_OPEN_CNX_ERROR_WRONG_DESTINATION		0x17
+/* This error code 0x18 is not used on SPCv */
+#define IO_OPEN_CNX_ERROR_UNKNOWN_ERROR			0x18
+#define IO_XFER_ERROR_NAK_RECEIVED			0x19
+#define IO_XFER_ERROR_ACK_NAK_TIMEOUT			0x1A
+#define IO_XFER_ERROR_PEER_ABORTED			0x1B
+#define IO_XFER_ERROR_RX_FRAME				0x1C
+#define IO_XFER_ERROR_DMA				0x1D
+#define IO_XFER_ERROR_CREDIT_TIMEOUT			0x1E
+#define IO_XFER_ERROR_SATA_LINK_TIMEOUT			0x1F
+#define IO_XFER_ERROR_SATA				0x20
+
+/* This error code 0x22 is not used on SPCv */
+#define IO_XFER_ERROR_ABORTED_DUE_TO_SRST		0x22
+#define IO_XFER_ERROR_REJECTED_NCQ_MODE			0x21
+#define IO_XFER_ERROR_ABORTED_NCQ_MODE			0x23
+#define IO_XFER_OPEN_RETRY_TIMEOUT			0x24
+/* This error code 0x25 is not used on SPCv */
+#define IO_XFER_SMP_RESP_CONNECTION_ERROR		0x25
+#define IO_XFER_ERROR_UNEXPECTED_PHASE			0x26
+#define IO_XFER_ERROR_XFER_RDY_OVERRUN			0x27
+#define IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED		0x28
+#define IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT		0x30
+
+/* The following error code 0x31 and 0x32 are not using (obsolete) */
+#define IO_XFER_ERROR_CMD_ISSUE_BREAK_BEFORE_ACK_NAK	0x31
+#define IO_XFER_ERROR_CMD_ISSUE_PHY_DOWN_BEFORE_ACK_NAK	0x32
+
+#define IO_XFER_ERROR_OFFSET_MISMATCH			0x34
+#define IO_XFER_ERROR_XFER_ZERO_DATA_LEN		0x35
+#define IO_XFER_CMD_FRAME_ISSUED			0x36
+#define IO_ERROR_INTERNAL_SMP_RESOURCE			0x37
+#define IO_PORT_IN_RESET				0x38
+#define IO_DS_NON_OPERATIONAL				0x39
+#define IO_DS_IN_RECOVERY				0x3A
+#define IO_TM_TAG_NOT_FOUND				0x3B
+#define IO_XFER_PIO_SETUP_ERROR				0x3C
+#define IO_SSP_EXT_IU_ZERO_LEN_ERROR			0x3D
+#define IO_DS_IN_ERROR					0x3E
+#define IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY		0x3F
+#define IO_ABORT_IN_PROGRESS				0x40
+#define IO_ABORT_DELAYED				0x41
+#define IO_INVALID_LENGTH				0x42
+
+/********** additional response event values *****************/
+
+#define IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY_ALT		0x43
+#define IO_XFER_OPEN_RETRY_BACKOFF_THRESHOLD_REACHED	0x44
+#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_TMO	0x45
+#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_NO_DEST		0x46
+#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_COLLIDE	0x47
+#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_PATHWAY_BLOCKED	0x48
+#define IO_DS_INVALID					0x49
+/* WARNING: the value is not contiguous from here */
+#define IO_XFER_ERR_LAST_PIO_DATAIN_CRC_ERR	0x52
+#define IO_XFER_DMA_ACTIVATE_TIMEOUT		0x53
+#define IO_XFER_ERROR_INTERNAL_CRC_ERROR	0x54
+#define MPI_IO_RQE_BUSY_FULL			0x55
+#define IO_XFER_ERR_EOB_DATA_OVERRUN		0x56
+#define IO_XFR_ERROR_INVALID_SSP_RSP_FRAME	0x57
+#define IO_OPEN_CNX_ERROR_OPEN_PREEMPTED	0x58
+
+#define MPI_ERR_IO_RESOURCE_UNAVAILABLE		0x1004
+#define MPI_ERR_ATAPI_DEVICE_BUSY		0x1024
+
+#define IO_XFR_ERROR_DEK_KEY_CACHE_MISS		0x2040
+/*
+ * An encryption IO request failed due to DEK Key Tag mismatch.
+ * The key tag supplied in the encryption IOMB does not match with
+ * the Key Tag in the referenced DEK Entry.
+ */
+#define IO_XFR_ERROR_DEK_KEY_TAG_MISMATCH	0x2041
+#define IO_XFR_ERROR_CIPHER_MODE_INVALID	0x2042
+/*
+ * An encryption I/O request failed because the initial value (IV)
+ * in the unwrapped DEK blob didn't match the IV used to unwrap it.
+ */
+#define IO_XFR_ERROR_DEK_IV_MISMATCH		0x2043
+/* An encryption I/O request failed due to an internal RAM ECC or
+ * interface error while unwrapping the DEK. */
+#define IO_XFR_ERROR_DEK_RAM_INTERFACE_ERROR	0x2044
+/* An encryption I/O request failed due to an internal RAM ECC or
+ * interface error while unwrapping the DEK. */
+#define IO_XFR_ERROR_INTERNAL_RAM		0x2045
+/*
+ * An encryption I/O request failed
+ * because the DEK index specified in the I/O was outside the bounds of
+ * the total number of entries in the host DEK table.
+ */
+#define IO_XFR_ERROR_DEK_INDEX_OUT_OF_BOUNDS0x2046
+
+/* define DIF IO response error status code */
+#define IO_XFR_ERROR_DIF_MISMATCH			0x3000
+#define IO_XFR_ERROR_DIF_APPLICATION_TAG_MISMATCH	0x3001
+#define IO_XFR_ERROR_DIF_REFERENCE_TAG_MISMATCH		0x3002
+#define IO_XFR_ERROR_DIF_CRC_MISMATCH			0x3003
+
+/* define operator management response status and error qualifier code */
+#define OPR_MGMT_OP_NOT_SUPPORTED			0x2060
+#define OPR_MGMT_MPI_ENC_ERR_OPR_PARAM_ILLEGAL		0x2061
+#define OPR_MGMT_MPI_ENC_ERR_OPR_ID_NOT_FOUND		0x2062
+#define OPR_MGMT_MPI_ENC_ERR_OPR_ROLE_NOT_MATCH		0x2063
+#define OPR_MGMT_MPI_ENC_ERR_OPR_MAX_NUM_EXCEEDED	0x2064
+#define OPR_MGMT_MPI_ENC_ERR_KEK_UNWRAP_FAIL		0x2022
+#define OPR_MGMT_MPI_ENC_ERR_NVRAM_OPERATION_FAILURE	0x2023
+/***************** additional response event values ***************/
+
+/* WARNING: This error code must always be the last number.
+ * If you add error code, modify this code also
+ * It is used as an index
+ */
+#define IO_ERROR_UNKNOWN_GENERIC			0x2023
+
+/* MSGU CONFIGURATION TABLE*/
+
+#define SPCv_MSGU_CFG_TABLE_UPDATE		0x001
+#define SPCv_MSGU_CFG_TABLE_RESET		0x002
+#define SPCv_MSGU_CFG_TABLE_FREEZE		0x004
+#define SPCv_MSGU_CFG_TABLE_UNFREEZE		0x008
+#define MSGU_IBDB_SET				0x00
+#define MSGU_HOST_INT_STATUS			0x08
+#define MSGU_HOST_INT_MASK			0x0C
+#define MSGU_IOPIB_INT_STATUS			0x18
+#define MSGU_IOPIB_INT_MASK			0x1C
+#define MSGU_IBDB_CLEAR				0x20
+
+#define MSGU_MSGU_CONTROL			0x24
+#define MSGU_ODR				0x20
+#define MSGU_ODCR				0x28
+
+#define MSGU_ODMR				0x30
+#define MSGU_ODMR_U				0x34
+#define MSGU_ODMR_CLR				0x38
+#define MSGU_ODMR_CLR_U				0x3C
+#define MSGU_OD_RSVD				0x40
+
+#define MSGU_SCRATCH_PAD_0			0x44
+#define MSGU_SCRATCH_PAD_1			0x48
+#define MSGU_SCRATCH_PAD_2			0x4C
+#define MSGU_SCRATCH_PAD_3			0x50
+#define MSGU_HOST_SCRATCH_PAD_0			0x54
+#define MSGU_HOST_SCRATCH_PAD_1			0x58
+#define MSGU_HOST_SCRATCH_PAD_2			0x5C
+#define MSGU_HOST_SCRATCH_PAD_3			0x60
+#define MSGU_HOST_SCRATCH_PAD_4			0x64
+#define MSGU_HOST_SCRATCH_PAD_5			0x68
+#define MSGU_HOST_SCRATCH_PAD_6			0x6C
+#define MSGU_HOST_SCRATCH_PAD_7			0x70
+
+/* bit definition for ODMR register */
+#define ODMR_MASK_ALL			0xFFFFFFFF/* mask all
+					interrupt vector */
+#define ODMR_CLEAR_ALL			0	/* clear all
+					interrupt vector */
+/* bit definition for ODCR register */
+#define ODCR_CLEAR_ALL			0xFFFFFFFF /* mask all
+					interrupt vector*/
+/* MSIX Interupts */
+#define MSIX_TABLE_OFFSET		0x2000
+#define MSIX_TABLE_ELEMENT_SIZE		0x10
+#define MSIX_INTERRUPT_CONTROL_OFFSET	0xC
+#define MSIX_TABLE_BASE			(MSIX_TABLE_OFFSET + \
+					MSIX_INTERRUPT_CONTROL_OFFSET)
+#define MSIX_INTERRUPT_DISABLE		0x1
+#define MSIX_INTERRUPT_ENABLE		0x0
+
+/* state definition for Scratch Pad1 register */
+#define SCRATCH_PAD_RAAE_READY		0x3
+#define SCRATCH_PAD_ILA_READY		0xC
+#define SCRATCH_PAD_BOOT_LOAD_SUCCESS	0x0
+#define SCRATCH_PAD_IOP0_READY		0xC00
+#define SCRATCH_PAD_IOP1_READY		0x3000
+
+/* boot loader state */
+#define SCRATCH_PAD1_BOOTSTATE_MASK		0x70	/* Bit 4-6 */
+#define SCRATCH_PAD1_BOOTSTATE_SUCESS		0x0	/* Load successful */
+#define SCRATCH_PAD1_BOOTSTATE_HDA_SEEPROM	0x10	/* HDA SEEPROM */
+#define SCRATCH_PAD1_BOOTSTATE_HDA_BOOTSTRAP	0x20	/* HDA BootStrap Pins */
+#define SCRATCH_PAD1_BOOTSTATE_HDA_SOFTRESET	0x30	/* HDA Soft Reset */
+#define SCRATCH_PAD1_BOOTSTATE_CRIT_ERROR	0x40	/* HDA critical error */
+#define SCRATCH_PAD1_BOOTSTATE_R1		0x50	/* Reserved */
+#define SCRATCH_PAD1_BOOTSTATE_R2		0x60	/* Reserved */
+#define SCRATCH_PAD1_BOOTSTATE_FATAL		0x70	/* Fatal Error */
+
+ /* state definition for Scratch Pad2 register */
+#define SCRATCH_PAD2_POR		0x00	/* power on state */
+#define SCRATCH_PAD2_SFR		0x01	/* soft reset state */
+#define SCRATCH_PAD2_ERR		0x02	/* error state */
+#define SCRATCH_PAD2_RDY		0x03	/* ready state */
+#define SCRATCH_PAD2_FWRDY_RST		0x04	/* FW rdy for soft reset flag */
+#define SCRATCH_PAD2_IOPRDY_RST		0x08	/* IOP ready for soft reset */
+#define SCRATCH_PAD2_STATE_MASK		0xFFFFFFF4 /* ScratchPad 2
+ Mask, bit1-0 State */
+#define SCRATCH_PAD2_RESERVED		0x000003FC/* Scratch Pad1
+ Reserved bit 2 to 9 */
+
+#define SCRATCH_PAD_ERROR_MASK		0xFFFFFC00 /* Error mask bits */
+#define SCRATCH_PAD_STATE_MASK		0x00000003 /* State Mask bits */
+
+/* main configuration offset - byte offset */
+#define MAIN_SIGNATURE_OFFSET		0x00 /* DWORD 0x00 */
+#define MAIN_INTERFACE_REVISION		0x04 /* DWORD 0x01 */
+#define MAIN_FW_REVISION		0x08 /* DWORD 0x02 */
+#define MAIN_MAX_OUTSTANDING_IO_OFFSET	0x0C /* DWORD 0x03 */
+#define MAIN_MAX_SGL_OFFSET		0x10 /* DWORD 0x04 */
+#define MAIN_CNTRL_CAP_OFFSET		0x14 /* DWORD 0x05 */
+#define MAIN_GST_OFFSET			0x18 /* DWORD 0x06 */
+#define MAIN_IBQ_OFFSET			0x1C /* DWORD 0x07 */
+#define MAIN_OBQ_OFFSET			0x20 /* DWORD 0x08 */
+#define MAIN_IQNPPD_HPPD_OFFSET		0x24 /* DWORD 0x09 */
+
+/* 0x28 - 0x4C - RSVD */
+#define MAIN_EVENT_CRC_CHECK		0x48 /* DWORD 0x12 */
+#define MAIN_EVENT_LOG_ADDR_HI		0x50 /* DWORD 0x14 */
+#define MAIN_EVENT_LOG_ADDR_LO		0x54 /* DWORD 0x15 */
+#define MAIN_EVENT_LOG_BUFF_SIZE	0x58 /* DWORD 0x16 */
+#define MAIN_EVENT_LOG_OPTION		0x5C /* DWORD 0x17 */
+#define MAIN_PCS_EVENT_LOG_ADDR_HI	0x60 /* DWORD 0x18 */
+#define MAIN_PCS_EVENT_LOG_ADDR_LO	0x64 /* DWORD 0x19 */
+#define MAIN_PCS_EVENT_LOG_BUFF_SIZE	0x68 /* DWORD 0x1A */
+#define MAIN_PCS_EVENT_LOG_OPTION	0x6C /* DWORD 0x1B */
+#define MAIN_FATAL_ERROR_INTERRUPT	0x70 /* DWORD 0x1C */
+#define MAIN_FATAL_ERROR_RDUMP0_OFFSET	0x74 /* DWORD 0x1D */
+#define MAIN_FATAL_ERROR_RDUMP0_LENGTH	0x78 /* DWORD 0x1E */
+#define MAIN_FATAL_ERROR_RDUMP1_OFFSET	0x7C /* DWORD 0x1F */
+#define MAIN_FATAL_ERROR_RDUMP1_LENGTH	0x80 /* DWORD 0x20 */
+#define MAIN_GPIO_LED_FLAGS_OFFSET	0x84 /* DWORD 0x21 */
+#define MAIN_ANALOG_SETUP_OFFSET	0x88 /* DWORD 0x22 */
+
+#define MAIN_INT_VECTOR_TABLE_OFFSET	0x8C /* DWORD 0x23 */
+#define MAIN_SAS_PHY_ATTR_TABLE_OFFSET	0x90 /* DWORD 0x24 */
+#define MAIN_PORT_RECOVERY_TIMER	0x94 /* DWORD 0x25 */
+#define MAIN_INT_REASSERTION_DELAY	0x98 /* DWORD 0x26 */
+
+/* Gereral Status Table offset - byte offset */
+#define GST_GSTLEN_MPIS_OFFSET		0x00
+#define GST_IQ_FREEZE_STATE0_OFFSET	0x04
+#define GST_IQ_FREEZE_STATE1_OFFSET	0x08
+#define GST_MSGUTCNT_OFFSET		0x0C
+#define GST_IOPTCNT_OFFSET		0x10
+/* 0x14 - 0x34 - RSVD */
+#define GST_GPIO_INPUT_VAL		0x38
+/* 0x3c - 0x40 - RSVD */
+#define GST_RERRINFO_OFFSET0		0x44
+#define GST_RERRINFO_OFFSET1		0x48
+#define GST_RERRINFO_OFFSET2		0x4c
+#define GST_RERRINFO_OFFSET3		0x50
+#define GST_RERRINFO_OFFSET4		0x54
+#define GST_RERRINFO_OFFSET5		0x58
+#define GST_RERRINFO_OFFSET6		0x5c
+#define GST_RERRINFO_OFFSET7		0x60
+
+/* General Status Table - MPI state */
+#define GST_MPI_STATE_UNINIT		0x00
+#define GST_MPI_STATE_INIT		0x01
+#define GST_MPI_STATE_TERMINATION	0x02
+#define GST_MPI_STATE_ERROR		0x03
+#define GST_MPI_STATE_MASK		0x07
+
+/* Per SAS PHY Attributes */
+
+#define PSPA_PHYSTATE0_OFFSET		0x00 /* Dword V */
+#define PSPA_OB_HW_EVENT_PID0_OFFSET	0x04 /* DWORD V+1 */
+#define PSPA_PHYSTATE1_OFFSET		0x08 /* Dword V+2 */
+#define PSPA_OB_HW_EVENT_PID1_OFFSET	0x0C /* DWORD V+3 */
+#define PSPA_PHYSTATE2_OFFSET		0x10 /* Dword V+4 */
+#define PSPA_OB_HW_EVENT_PID2_OFFSET	0x14 /* DWORD V+5 */
+#define PSPA_PHYSTATE3_OFFSET		0x18 /* Dword V+6 */
+#define PSPA_OB_HW_EVENT_PID3_OFFSET	0x1C /* DWORD V+7 */
+#define PSPA_PHYSTATE4_OFFSET		0x20 /* Dword V+8 */
+#define PSPA_OB_HW_EVENT_PID4_OFFSET	0x24 /* DWORD V+9 */
+#define PSPA_PHYSTATE5_OFFSET		0x28 /* Dword V+10 */
+#define PSPA_OB_HW_EVENT_PID5_OFFSET	0x2C /* DWORD V+11 */
+#define PSPA_PHYSTATE6_OFFSET		0x30 /* Dword V+12 */
+#define PSPA_OB_HW_EVENT_PID6_OFFSET	0x34 /* DWORD V+13 */
+#define PSPA_PHYSTATE7_OFFSET		0x38 /* Dword V+14 */
+#define PSPA_OB_HW_EVENT_PID7_OFFSET	0x3C /* DWORD V+15 */
+#define PSPA_PHYSTATE8_OFFSET		0x40 /* DWORD V+16 */
+#define PSPA_OB_HW_EVENT_PID8_OFFSET	0x44 /* DWORD V+17 */
+#define PSPA_PHYSTATE9_OFFSET		0x48 /* DWORD V+18 */
+#define PSPA_OB_HW_EVENT_PID9_OFFSET	0x4C /* DWORD V+19 */
+#define PSPA_PHYSTATE10_OFFSET		0x50 /* DWORD V+20 */
+#define PSPA_OB_HW_EVENT_PID10_OFFSET	0x54 /* DWORD V+21 */
+#define PSPA_PHYSTATE11_OFFSET		0x58 /* DWORD V+22 */
+#define PSPA_OB_HW_EVENT_PID11_OFFSET	0x5C /* DWORD V+23 */
+#define PSPA_PHYSTATE12_OFFSET		0x60 /* DWORD V+24 */
+#define PSPA_OB_HW_EVENT_PID12_OFFSET	0x64 /* DWORD V+25 */
+#define PSPA_PHYSTATE13_OFFSET		0x68 /* DWORD V+26 */
+#define PSPA_OB_HW_EVENT_PID13_OFFSET	0x6c /* DWORD V+27 */
+#define PSPA_PHYSTATE14_OFFSET		0x70 /* DWORD V+28 */
+#define PSPA_OB_HW_EVENT_PID14_OFFSET	0x74 /* DWORD V+29 */
+#define PSPA_PHYSTATE15_OFFSET		0x78 /* DWORD V+30 */
+#define PSPA_OB_HW_EVENT_PID15_OFFSET	0x7c /* DWORD V+31 */
+/* end PSPA */
+
+/* inbound queue configuration offset - byte offset */
+#define IB_PROPERITY_OFFSET		0x00
+#define IB_BASE_ADDR_HI_OFFSET		0x04
+#define IB_BASE_ADDR_LO_OFFSET		0x08
+#define IB_CI_BASE_ADDR_HI_OFFSET	0x0C
+#define IB_CI_BASE_ADDR_LO_OFFSET	0x10
+#define IB_PIPCI_BAR			0x14
+#define IB_PIPCI_BAR_OFFSET		0x18
+#define IB_RESERVED_OFFSET		0x1C
+
+/* outbound queue configuration offset - byte offset */
+#define OB_PROPERITY_OFFSET		0x00
+#define OB_BASE_ADDR_HI_OFFSET		0x04
+#define OB_BASE_ADDR_LO_OFFSET		0x08
+#define OB_PI_BASE_ADDR_HI_OFFSET	0x0C
+#define OB_PI_BASE_ADDR_LO_OFFSET	0x10
+#define OB_CIPCI_BAR			0x14
+#define OB_CIPCI_BAR_OFFSET		0x18
+#define OB_INTERRUPT_COALES_OFFSET	0x1C
+#define OB_DYNAMIC_COALES_OFFSET	0x20
+#define OB_PROPERTY_INT_ENABLE		0x40000000
+
+#define MBIC_NMI_ENABLE_VPE0_IOP	0x000418
+#define MBIC_NMI_ENABLE_VPE0_AAP1	0x000418
+/* PCIE registers - BAR2(0x18), BAR1(win) 0x010000 */
+#define PCIE_EVENT_INTERRUPT_ENABLE	0x003040
+#define PCIE_EVENT_INTERRUPT		0x003044
+#define PCIE_ERROR_INTERRUPT_ENABLE	0x003048
+#define PCIE_ERROR_INTERRUPT		0x00304C
+
+/* SPCV soft reset */
+#define SPC_REG_SOFT_RESET 0x00001000
+#define SPCv_NORMAL_RESET_VALUE		0x1
+
+#define SPCv_SOFT_RESET_READ_MASK		0xC0
+#define SPCv_SOFT_RESET_NO_RESET		0x0
+#define SPCv_SOFT_RESET_NORMAL_RESET_OCCURED	0x40
+#define SPCv_SOFT_RESET_HDA_MODE_OCCURED	0x80
+#define SPCv_SOFT_RESET_CHIP_RESET_OCCURED	0xC0
+
+/* signature definition for host scratch pad0 register */
+#define SPC_SOFT_RESET_SIGNATURE	0x252acbcd
+/* Signature for Soft Reset */
+
+/* SPC Reset register - BAR4(0x20), BAR2(win) (need dynamic mapping) */
+#define SPC_REG_RESET			0x000000/* reset register */
+
+/* bit definition for SPC_RESET register */
+#define SPC_REG_RESET_OSSP		0x00000001
+#define SPC_REG_RESET_RAAE		0x00000002
+#define SPC_REG_RESET_PCS_SPBC		0x00000004
+#define SPC_REG_RESET_PCS_IOP_SS	0x00000008
+#define SPC_REG_RESET_PCS_AAP1_SS	0x00000010
+#define SPC_REG_RESET_PCS_AAP2_SS	0x00000020
+#define SPC_REG_RESET_PCS_LM		0x00000040
+#define SPC_REG_RESET_PCS		0x00000080
+#define SPC_REG_RESET_GSM		0x00000100
+#define SPC_REG_RESET_DDR2		0x00010000
+#define SPC_REG_RESET_BDMA_CORE		0x00020000
+#define SPC_REG_RESET_BDMA_SXCBI	0x00040000
+#define SPC_REG_RESET_PCIE_AL_SXCBI	0x00080000
+#define SPC_REG_RESET_PCIE_PWR		0x00100000
+#define SPC_REG_RESET_PCIE_SFT		0x00200000
+#define SPC_REG_RESET_PCS_SXCBI		0x00400000
+#define SPC_REG_RESET_LMS_SXCBI		0x00800000
+#define SPC_REG_RESET_PMIC_SXCBI	0x01000000
+#define SPC_REG_RESET_PMIC_CORE		0x02000000
+#define SPC_REG_RESET_PCIE_PC_SXCBI	0x04000000
+#define SPC_REG_RESET_DEVICE		0x80000000
+
+/* registers for BAR Shifting - BAR2(0x18), BAR1(win) */
+#define SPCV_IBW_AXI_TRANSLATION_LOW	0x001010
+
+#define MBIC_AAP1_ADDR_BASE		0x060000
+#define MBIC_IOP_ADDR_BASE		0x070000
+#define GSM_ADDR_BASE			0x0700000
+/* Dynamic map through Bar4 - 0x00700000 */
+#define GSM_CONFIG_RESET		0x00000000
+#define RAM_ECC_DB_ERR			0x00000018
+#define GSM_READ_ADDR_PARITY_INDIC	0x00000058
+#define GSM_WRITE_ADDR_PARITY_INDIC	0x00000060
+#define GSM_WRITE_DATA_PARITY_INDIC	0x00000068
+#define GSM_READ_ADDR_PARITY_CHECK	0x00000038
+#define GSM_WRITE_ADDR_PARITY_CHECK	0x00000040
+#define GSM_WRITE_DATA_PARITY_CHECK	0x00000048
+
+#define RB6_ACCESS_REG			0x6A0000
+#define HDAC_EXEC_CMD			0x0002
+#define HDA_C_PA			0xcb
+#define HDA_SEQ_ID_BITS			0x00ff0000
+#define HDA_GSM_OFFSET_BITS		0x00FFFFFF
+#define HDA_GSM_CMD_OFFSET_BITS		0x42C0
+#define HDA_GSM_RSP_OFFSET_BITS		0x42E0
+
+#define MBIC_AAP1_ADDR_BASE		0x060000
+#define MBIC_IOP_ADDR_BASE		0x070000
+#define GSM_ADDR_BASE			0x0700000
+#define SPC_TOP_LEVEL_ADDR_BASE		0x000000
+#define GSM_CONFIG_RESET_VALUE		0x00003b00
+#define GPIO_ADDR_BASE			0x00090000
+#define GPIO_GPIO_0_0UTPUT_CTL_OFFSET	0x0000010c
+
+/* RB6 offset */
+#define SPC_RB6_OFFSET			0x80C0
+/* Magic number of soft reset for RB6 */
+#define RB6_MAGIC_NUMBER_RST		0x1234
+
+/* Device Register status */
+#define DEVREG_SUCCESS					0x00
+#define DEVREG_FAILURE_OUT_OF_RESOURCE			0x01
+#define DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED	0x02
+#define DEVREG_FAILURE_INVALID_PHY_ID			0x03
+#define DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED	0x04
+#define DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE		0x05
+#define DEVREG_FAILURE_PORT_NOT_VALID_STATE		0x06
+#define DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID		0x07
+
+
+#define MEMBASE_II_SHIFT_REGISTER       0x1010
+#endif