Initial import

1 files changed, 1384 insertions, 0 deletions

diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c
new file mode 100644
index 000000000..1dab9dfbc
--- /dev/null
+++ b/drivers/usb/host/ohci-hcd.c
@@ -0,0 +1,1384 @@
+/*
+ * Open Host Controller Interface (OHCI) driver for USB.
+ *
+ * Maintainer: Alan Stern <stern@rowland.harvard.edu>
+ *
+ * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
+ * (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net>
+ *
+ * [ Initialisation is based on Linus'  ]
+ * [ uhci code and gregs ohci fragments ]
+ * [ (C) Copyright 1999 Linus Torvalds  ]
+ * [ (C) Copyright 1999 Gregory P. Smith]
+ *
+ *
+ * OHCI is the main "non-Intel/VIA" standard for USB 1.1 host controller
+ * interfaces (though some non-x86 Intel chips use it).  It supports
+ * smarter hardware than UHCI.  A download link for the spec available
+ * through the http://www.usb.org website.
+ *
+ * This file is licenced under the GPL.
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/ioport.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/timer.h>
+#include <linux/list.h>
+#include <linux/usb.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/hcd.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
+#include <linux/workqueue.h>
+#include <linux/debugfs.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/unaligned.h>
+#include <asm/byteorder.h>
+
+
+#define DRIVER_AUTHOR "Roman Weissgaerber, David Brownell"
+#define DRIVER_DESC "USB 1.1 'Open' Host Controller (OHCI) Driver"
+
+/*-------------------------------------------------------------------------*/
+
+/* For initializing controller (mask in an HCFS mode too) */
+#define	OHCI_CONTROL_INIT	OHCI_CTRL_CBSR
+#define	OHCI_INTR_INIT \
+		(OHCI_INTR_MIE | OHCI_INTR_RHSC | OHCI_INTR_UE \
+		| OHCI_INTR_RD | OHCI_INTR_WDH)
+
+#ifdef __hppa__
+/* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */
+#define	IR_DISABLE
+#endif
+
+#ifdef CONFIG_ARCH_OMAP
+/* OMAP doesn't support IR (no SMM; not needed) */
+#define	IR_DISABLE
+#endif
+
+/*-------------------------------------------------------------------------*/
+
+static const char	hcd_name [] = "ohci_hcd";
+
+#define	STATECHANGE_DELAY	msecs_to_jiffies(300)
+#define	IO_WATCHDOG_DELAY	msecs_to_jiffies(250)
+
+#include "ohci.h"
+#include "pci-quirks.h"
+
+static void ohci_dump(struct ohci_hcd *ohci);
+static void ohci_stop(struct usb_hcd *hcd);
+static void io_watchdog_func(unsigned long _ohci);
+
+#include "ohci-hub.c"
+#include "ohci-dbg.c"
+#include "ohci-mem.c"
+#include "ohci-q.c"
+
+
+/*
+ * On architectures with edge-triggered interrupts we must never return
+ * IRQ_NONE.
+ */
+#if defined(CONFIG_SA1111)  /* ... or other edge-triggered systems */
+#define IRQ_NOTMINE	IRQ_HANDLED
+#else
+#define IRQ_NOTMINE	IRQ_NONE
+#endif
+
+
+/* Some boards misreport power switching/overcurrent */
+static bool distrust_firmware = 1;
+module_param (distrust_firmware, bool, 0);
+MODULE_PARM_DESC (distrust_firmware,
+	"true to distrust firmware power/overcurrent setup");
+
+/* Some boards leave IR set wrongly, since they fail BIOS/SMM handshakes */
+static bool no_handshake = 0;
+module_param (no_handshake, bool, 0);
+MODULE_PARM_DESC (no_handshake, "true (not default) disables BIOS handshake");
+
+/*-------------------------------------------------------------------------*/
+
+static int number_of_tds(struct urb *urb)
+{
+	int			len, i, num, this_sg_len;
+	struct scatterlist	*sg;
+
+	len = urb->transfer_buffer_length;
+	i = urb->num_mapped_sgs;
+
+	if (len > 0 && i > 0) {		/* Scatter-gather transfer */
+		num = 0;
+		sg = urb->sg;
+		for (;;) {
+			this_sg_len = min_t(int, sg_dma_len(sg), len);
+			num += DIV_ROUND_UP(this_sg_len, 4096);
+			len -= this_sg_len;
+			if (--i <= 0 || len <= 0)
+				break;
+			sg = sg_next(sg);
+		}
+
+	} else {			/* Non-SG transfer */
+		/* one TD for every 4096 Bytes (could be up to 8K) */
+		num = DIV_ROUND_UP(len, 4096);
+	}
+	return num;
+}
+
+/*
+ * queue up an urb for anything except the root hub
+ */
+static int ohci_urb_enqueue (
+	struct usb_hcd	*hcd,
+	struct urb	*urb,
+	gfp_t		mem_flags
+) {
+	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
+	struct ed	*ed;
+	urb_priv_t	*urb_priv;
+	unsigned int	pipe = urb->pipe;
+	int		i, size = 0;
+	unsigned long	flags;
+	int		retval = 0;
+
+	/* every endpoint has a ed, locate and maybe (re)initialize it */
+	if (! (ed = ed_get (ohci, urb->ep, urb->dev, pipe, urb->interval)))
+		return -ENOMEM;
+
+	/* for the private part of the URB we need the number of TDs (size) */
+	switch (ed->type) {
+		case PIPE_CONTROL:
+			/* td_submit_urb() doesn't yet handle these */
+			if (urb->transfer_buffer_length > 4096)
+				return -EMSGSIZE;
+
+			/* 1 TD for setup, 1 for ACK, plus ... */
+			size = 2;
+			/* FALLTHROUGH */
+		// case PIPE_INTERRUPT:
+		// case PIPE_BULK:
+		default:
+			size += number_of_tds(urb);
+			/* maybe a zero-length packet to wrap it up */
+			if (size == 0)
+				size++;
+			else if ((urb->transfer_flags & URB_ZERO_PACKET) != 0
+				&& (urb->transfer_buffer_length
+					% usb_maxpacket (urb->dev, pipe,
+						usb_pipeout (pipe))) == 0)
+				size++;
+			break;
+		case PIPE_ISOCHRONOUS: /* number of packets from URB */
+			size = urb->number_of_packets;
+			break;
+	}
+
+	/* allocate the private part of the URB */
+	urb_priv = kzalloc (sizeof (urb_priv_t) + size * sizeof (struct td *),
+			mem_flags);
+	if (!urb_priv)
+		return -ENOMEM;
+	INIT_LIST_HEAD (&urb_priv->pending);
+	urb_priv->length = size;
+	urb_priv->ed = ed;
+
+	/* allocate the TDs (deferring hash chain updates) */
+	for (i = 0; i < size; i++) {
+		urb_priv->td [i] = td_alloc (ohci, mem_flags);
+		if (!urb_priv->td [i]) {
+			urb_priv->length = i;
+			urb_free_priv (ohci, urb_priv);
+			return -ENOMEM;
+		}
+	}
+
+	spin_lock_irqsave (&ohci->lock, flags);
+
+	/* don't submit to a dead HC */
+	if (!HCD_HW_ACCESSIBLE(hcd)) {
+		retval = -ENODEV;
+		goto fail;
+	}
+	if (ohci->rh_state != OHCI_RH_RUNNING) {
+		retval = -ENODEV;
+		goto fail;
+	}
+	retval = usb_hcd_link_urb_to_ep(hcd, urb);
+	if (retval)
+		goto fail;
+
+	/* schedule the ed if needed */
+	if (ed->state == ED_IDLE) {
+		retval = ed_schedule (ohci, ed);
+		if (retval < 0) {
+			usb_hcd_unlink_urb_from_ep(hcd, urb);
+			goto fail;
+		}
+
+		/* Start up the I/O watchdog timer, if it's not running */
+		if (!timer_pending(&ohci->io_watchdog) &&
+				list_empty(&ohci->eds_in_use)) {
+			ohci->prev_frame_no = ohci_frame_no(ohci);
+			mod_timer(&ohci->io_watchdog,
+					jiffies + IO_WATCHDOG_DELAY);
+		}
+		list_add(&ed->in_use_list, &ohci->eds_in_use);
+
+		if (ed->type == PIPE_ISOCHRONOUS) {
+			u16	frame = ohci_frame_no(ohci);
+
+			/* delay a few frames before the first TD */
+			frame += max_t (u16, 8, ed->interval);
+			frame &= ~(ed->interval - 1);
+			frame |= ed->branch;
+			urb->start_frame = frame;
+			ed->last_iso = frame + ed->interval * (size - 1);
+		}
+	} else if (ed->type == PIPE_ISOCHRONOUS) {
+		u16	next = ohci_frame_no(ohci) + 1;
+		u16	frame = ed->last_iso + ed->interval;
+		u16	length = ed->interval * (size - 1);
+
+		/* Behind the scheduling threshold? */
+		if (unlikely(tick_before(frame, next))) {
+
+			/* URB_ISO_ASAP: Round up to the first available slot */
+			if (urb->transfer_flags & URB_ISO_ASAP) {
+				frame += (next - frame + ed->interval - 1) &
+						-ed->interval;
+
+			/*
+			 * Not ASAP: Use the next slot in the stream,
+			 * no matter what.
+			 */
+			} else {
+				/*
+				 * Some OHCI hardware doesn't handle late TDs
+				 * correctly.  After retiring them it proceeds
+				 * to the next ED instead of the next TD.
+				 * Therefore we have to omit the late TDs
+				 * entirely.
+				 */
+				urb_priv->td_cnt = DIV_ROUND_UP(
+						(u16) (next - frame),
+						ed->interval);
+				if (urb_priv->td_cnt >= urb_priv->length) {
+					++urb_priv->td_cnt;	/* Mark it */
+					ohci_dbg(ohci, "iso underrun %p (%u+%u < %u)\n",
+							urb, frame, length,
+							next);
+				}
+			}
+		}
+		urb->start_frame = frame;
+		ed->last_iso = frame + length;
+	}
+
+	/* fill the TDs and link them to the ed; and
+	 * enable that part of the schedule, if needed
+	 * and update count of queued periodic urbs
+	 */
+	urb->hcpriv = urb_priv;
+	td_submit_urb (ohci, urb);
+
+fail:
+	if (retval)
+		urb_free_priv (ohci, urb_priv);
+	spin_unlock_irqrestore (&ohci->lock, flags);
+	return retval;
+}
+
+/*
+ * decouple the URB from the HC queues (TDs, urb_priv).
+ * reporting is always done
+ * asynchronously, and we might be dealing with an urb that's
+ * partially transferred, or an ED with other urbs being unlinked.
+ */
+static int ohci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
+{
+	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
+	unsigned long		flags;
+	int			rc;
+	urb_priv_t		*urb_priv;
+
+	spin_lock_irqsave (&ohci->lock, flags);
+	rc = usb_hcd_check_unlink_urb(hcd, urb, status);
+	if (rc == 0) {
+
+		/* Unless an IRQ completed the unlink while it was being
+		 * handed to us, flag it for unlink and giveback, and force
+		 * some upcoming INTR_SF to call finish_unlinks()
+		 */
+		urb_priv = urb->hcpriv;
+		if (urb_priv->ed->state == ED_OPER)
+			start_ed_unlink(ohci, urb_priv->ed);
+
+		if (ohci->rh_state != OHCI_RH_RUNNING) {
+			/* With HC dead, we can clean up right away */
+			ohci_work(ohci);
+		}
+	}
+	spin_unlock_irqrestore (&ohci->lock, flags);
+	return rc;
+}
+
+/*-------------------------------------------------------------------------*/
+
+/* frees config/altsetting state for endpoints,
+ * including ED memory, dummy TD, and bulk/intr data toggle
+ */
+
+static void
+ohci_endpoint_disable (struct usb_hcd *hcd, struct usb_host_endpoint *ep)
+{
+	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
+	unsigned long		flags;
+	struct ed		*ed = ep->hcpriv;
+	unsigned		limit = 1000;
+
+	/* ASSERT:  any requests/urbs are being unlinked */
+	/* ASSERT:  nobody can be submitting urbs for this any more */
+
+	if (!ed)
+		return;
+
+rescan:
+	spin_lock_irqsave (&ohci->lock, flags);
+
+	if (ohci->rh_state != OHCI_RH_RUNNING) {
+sanitize:
+		ed->state = ED_IDLE;
+		ohci_work(ohci);
+	}
+
+	switch (ed->state) {
+	case ED_UNLINK:		/* wait for hw to finish? */
+		/* major IRQ delivery trouble loses INTR_SF too... */
+		if (limit-- == 0) {
+			ohci_warn(ohci, "ED unlink timeout\n");
+			goto sanitize;
+		}
+		spin_unlock_irqrestore (&ohci->lock, flags);
+		schedule_timeout_uninterruptible(1);
+		goto rescan;
+	case ED_IDLE:		/* fully unlinked */
+		if (list_empty (&ed->td_list)) {
+			td_free (ohci, ed->dummy);
+			ed_free (ohci, ed);
+			break;
+		}
+		/* else FALL THROUGH */
+	default:
+		/* caller was supposed to have unlinked any requests;
+		 * that's not our job.  can't recover; must leak ed.
+		 */
+		ohci_err (ohci, "leak ed %p (#%02x) state %d%s\n",
+			ed, ep->desc.bEndpointAddress, ed->state,
+			list_empty (&ed->td_list) ? "" : " (has tds)");
+		td_free (ohci, ed->dummy);
+		break;
+	}
+	ep->hcpriv = NULL;
+	spin_unlock_irqrestore (&ohci->lock, flags);
+}
+
+static int ohci_get_frame (struct usb_hcd *hcd)
+{
+	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
+
+	return ohci_frame_no(ohci);
+}
+
+static void ohci_usb_reset (struct ohci_hcd *ohci)
+{
+	ohci->hc_control = ohci_readl (ohci, &ohci->regs->control);
+	ohci->hc_control &= OHCI_CTRL_RWC;
+	ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
+	ohci->rh_state = OHCI_RH_HALTED;
+}
+
+/* ohci_shutdown forcibly disables IRQs and DMA, helping kexec and
+ * other cases where the next software may expect clean state from the
+ * "firmware".  this is bus-neutral, unlike shutdown() methods.
+ */
+static void
+ohci_shutdown (struct usb_hcd *hcd)
+{
+	struct ohci_hcd *ohci;
+
+	ohci = hcd_to_ohci (hcd);
+	ohci_writel(ohci, (u32) ~0, &ohci->regs->intrdisable);
+
+	/* Software reset, after which the controller goes into SUSPEND */
+	ohci_writel(ohci, OHCI_HCR, &ohci->regs->cmdstatus);
+	ohci_readl(ohci, &ohci->regs->cmdstatus);	/* flush the writes */
+	udelay(10);
+
+	ohci_writel(ohci, ohci->fminterval, &ohci->regs->fminterval);
+	ohci->rh_state = OHCI_RH_HALTED;
+}
+
+/*-------------------------------------------------------------------------*
+ * HC functions
+ *-------------------------------------------------------------------------*/
+
+/* init memory, and kick BIOS/SMM off */
+
+static int ohci_init (struct ohci_hcd *ohci)
+{
+	int ret;
+	struct usb_hcd *hcd = ohci_to_hcd(ohci);
+
+	/* Accept arbitrarily long scatter-gather lists */
+	hcd->self.sg_tablesize = ~0;
+
+	if (distrust_firmware)
+		ohci->flags |= OHCI_QUIRK_HUB_POWER;
+
+	ohci->rh_state = OHCI_RH_HALTED;
+	ohci->regs = hcd->regs;
+
+	/* REVISIT this BIOS handshake is now moved into PCI "quirks", and
+	 * was never needed for most non-PCI systems ... remove the code?
+	 */
+
+#ifndef IR_DISABLE
+	/* SMM owns the HC?  not for long! */
+	if (!no_handshake && ohci_readl (ohci,
+					&ohci->regs->control) & OHCI_CTRL_IR) {
+		u32 temp;
+
+		ohci_dbg (ohci, "USB HC TakeOver from BIOS/SMM\n");
+
+		/* this timeout is arbitrary.  we make it long, so systems
+		 * depending on usb keyboards may be usable even if the
+		 * BIOS/SMM code seems pretty broken.
+		 */
+		temp = 500;	/* arbitrary: five seconds */
+
+		ohci_writel (ohci, OHCI_INTR_OC, &ohci->regs->intrenable);
+		ohci_writel (ohci, OHCI_OCR, &ohci->regs->cmdstatus);
+		while (ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_IR) {
+			msleep (10);
+			if (--temp == 0) {
+				ohci_err (ohci, "USB HC takeover failed!"
+					"  (BIOS/SMM bug)\n");
+				return -EBUSY;
+			}
+		}
+		ohci_usb_reset (ohci);
+	}
+#endif
+
+	/* Disable HC interrupts */
+	ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
+
+	/* flush the writes, and save key bits like RWC */
+	if (ohci_readl (ohci, &ohci->regs->control) & OHCI_CTRL_RWC)
+		ohci->hc_control |= OHCI_CTRL_RWC;
+
+	/* Read the number of ports unless overridden */
+	if (ohci->num_ports == 0)
+		ohci->num_ports = roothub_a(ohci) & RH_A_NDP;
+
+	if (ohci->hcca)
+		return 0;
+
+	setup_timer(&ohci->io_watchdog, io_watchdog_func,
+			(unsigned long) ohci);
+	set_timer_slack(&ohci->io_watchdog, msecs_to_jiffies(20));
+
+	ohci->hcca = dma_alloc_coherent (hcd->self.controller,
+			sizeof(*ohci->hcca), &ohci->hcca_dma, GFP_KERNEL);
+	if (!ohci->hcca)
+		return -ENOMEM;
+
+	if ((ret = ohci_mem_init (ohci)) < 0)
+		ohci_stop (hcd);
+	else {
+		create_debug_files (ohci);
+	}
+
+	return ret;
+}
+
+/*-------------------------------------------------------------------------*/
+
+/* Start an OHCI controller, set the BUS operational
+ * resets USB and controller
+ * enable interrupts
+ */
+static int ohci_run (struct ohci_hcd *ohci)
+{
+	u32			mask, val;
+	int			first = ohci->fminterval == 0;
+	struct usb_hcd		*hcd = ohci_to_hcd(ohci);
+
+	ohci->rh_state = OHCI_RH_HALTED;
+
+	/* boot firmware should have set this up (5.1.1.3.1) */
+	if (first) {
+
+		val = ohci_readl (ohci, &ohci->regs->fminterval);
+		ohci->fminterval = val & 0x3fff;
+		if (ohci->fminterval != FI)
+			ohci_dbg (ohci, "fminterval delta %d\n",
+				ohci->fminterval - FI);
+		ohci->fminterval |= FSMP (ohci->fminterval) << 16;
+		/* also: power/overcurrent flags in roothub.a */
+	}
+
+	/* Reset USB nearly "by the book".  RemoteWakeupConnected has
+	 * to be checked in case boot firmware (BIOS/SMM/...) has set up
+	 * wakeup in a way the bus isn't aware of (e.g., legacy PCI PM).
+	 * If the bus glue detected wakeup capability then it should
+	 * already be enabled; if so we'll just enable it again.
+	 */
+	if ((ohci->hc_control & OHCI_CTRL_RWC) != 0)
+		device_set_wakeup_capable(hcd->self.controller, 1);
+
+	switch (ohci->hc_control & OHCI_CTRL_HCFS) {
+	case OHCI_USB_OPER:
+		val = 0;
+		break;
+	case OHCI_USB_SUSPEND:
+	case OHCI_USB_RESUME:
+		ohci->hc_control &= OHCI_CTRL_RWC;
+		ohci->hc_control |= OHCI_USB_RESUME;
+		val = 10 /* msec wait */;
+		break;
+	// case OHCI_USB_RESET:
+	default:
+		ohci->hc_control &= OHCI_CTRL_RWC;
+		ohci->hc_control |= OHCI_USB_RESET;
+		val = 50 /* msec wait */;
+		break;
+	}
+	ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
+	// flush the writes
+	(void) ohci_readl (ohci, &ohci->regs->control);
+	msleep(val);
+
+	memset (ohci->hcca, 0, sizeof (struct ohci_hcca));
+
+	/* 2msec timelimit here means no irqs/preempt */
+	spin_lock_irq (&ohci->lock);
+
+retry:
+	/* HC Reset requires max 10 us delay */
+	ohci_writel (ohci, OHCI_HCR,  &ohci->regs->cmdstatus);
+	val = 30;	/* ... allow extra time */
+	while ((ohci_readl (ohci, &ohci->regs->cmdstatus) & OHCI_HCR) != 0) {
+		if (--val == 0) {
+			spin_unlock_irq (&ohci->lock);
+			ohci_err (ohci, "USB HC reset timed out!\n");
+			return -1;
+		}
+		udelay (1);
+	}
+
+	/* now we're in the SUSPEND state ... must go OPERATIONAL
+	 * within 2msec else HC enters RESUME
+	 *
+	 * ... but some hardware won't init fmInterval "by the book"
+	 * (SiS, OPTi ...), so reset again instead.  SiS doesn't need
+	 * this if we write fmInterval after we're OPERATIONAL.
+	 * Unclear about ALi, ServerWorks, and others ... this could
+	 * easily be a longstanding bug in chip init on Linux.
+	 */
+	if (ohci->flags & OHCI_QUIRK_INITRESET) {
+		ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
+		// flush those writes
+		(void) ohci_readl (ohci, &ohci->regs->control);
+	}
+
+	/* Tell the controller where the control and bulk lists are
+	 * The lists are empty now. */
+	ohci_writel (ohci, 0, &ohci->regs->ed_controlhead);
+	ohci_writel (ohci, 0, &ohci->regs->ed_bulkhead);
+
+	/* a reset clears this */
+	ohci_writel (ohci, (u32) ohci->hcca_dma, &ohci->regs->hcca);
+
+	periodic_reinit (ohci);
+
+	/* some OHCI implementations are finicky about how they init.
+	 * bogus values here mean not even enumeration could work.
+	 */
+	if ((ohci_readl (ohci, &ohci->regs->fminterval) & 0x3fff0000) == 0
+			|| !ohci_readl (ohci, &ohci->regs->periodicstart)) {
+		if (!(ohci->flags & OHCI_QUIRK_INITRESET)) {
+			ohci->flags |= OHCI_QUIRK_INITRESET;
+			ohci_dbg (ohci, "enabling initreset quirk\n");
+			goto retry;
+		}
+		spin_unlock_irq (&ohci->lock);
+		ohci_err (ohci, "init err (%08x %04x)\n",
+			ohci_readl (ohci, &ohci->regs->fminterval),
+			ohci_readl (ohci, &ohci->regs->periodicstart));
+		return -EOVERFLOW;
+	}
+
+	/* use rhsc irqs after hub_wq is allocated */
+	set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+	hcd->uses_new_polling = 1;
+
+	/* start controller operations */
+	ohci->hc_control &= OHCI_CTRL_RWC;
+	ohci->hc_control |= OHCI_CONTROL_INIT | OHCI_USB_OPER;
+	ohci_writel (ohci, ohci->hc_control, &ohci->regs->control);
+	ohci->rh_state = OHCI_RH_RUNNING;
+
+	/* wake on ConnectStatusChange, matching external hubs */
+	ohci_writel (ohci, RH_HS_DRWE, &ohci->regs->roothub.status);
+
+	/* Choose the interrupts we care about now, others later on demand */
+	mask = OHCI_INTR_INIT;
+	ohci_writel (ohci, ~0, &ohci->regs->intrstatus);
+	ohci_writel (ohci, mask, &ohci->regs->intrenable);
+
+	/* handle root hub init quirks ... */
+	val = roothub_a (ohci);
+	val &= ~(RH_A_PSM | RH_A_OCPM);
+	if (ohci->flags & OHCI_QUIRK_SUPERIO) {
+		/* NSC 87560 and maybe others */
+		val |= RH_A_NOCP;
+		val &= ~(RH_A_POTPGT | RH_A_NPS);
+		ohci_writel (ohci, val, &ohci->regs->roothub.a);
+	} else if ((ohci->flags & OHCI_QUIRK_AMD756) ||
+			(ohci->flags & OHCI_QUIRK_HUB_POWER)) {
+		/* hub power always on; required for AMD-756 and some
+		 * Mac platforms.  ganged overcurrent reporting, if any.
+		 */
+		val |= RH_A_NPS;
+		ohci_writel (ohci, val, &ohci->regs->roothub.a);
+	}
+	ohci_writel (ohci, RH_HS_LPSC, &ohci->regs->roothub.status);
+	ohci_writel (ohci, (val & RH_A_NPS) ? 0 : RH_B_PPCM,
+						&ohci->regs->roothub.b);
+	// flush those writes
+	(void) ohci_readl (ohci, &ohci->regs->control);
+
+	ohci->next_statechange = jiffies + STATECHANGE_DELAY;
+	spin_unlock_irq (&ohci->lock);
+
+	// POTPGT delay is bits 24-31, in 2 ms units.
+	mdelay ((val >> 23) & 0x1fe);
+
+	ohci_dump(ohci);
+
+	return 0;
+}
+
+/* ohci_setup routine for generic controller initialization */
+
+int ohci_setup(struct usb_hcd *hcd)
+{
+	struct ohci_hcd		*ohci = hcd_to_ohci(hcd);
+
+	ohci_hcd_init(ohci);
+	
+	return ohci_init(ohci);
+}
+EXPORT_SYMBOL_GPL(ohci_setup);
+
+/* ohci_start routine for generic controller start of all OHCI bus glue */
+static int ohci_start(struct usb_hcd *hcd)
+{
+	struct ohci_hcd		*ohci = hcd_to_ohci(hcd);
+	int	ret;
+
+	ret = ohci_run(ohci);
+	if (ret < 0) {
+		ohci_err(ohci, "can't start\n");
+		ohci_stop(hcd);
+	}
+	return ret;
+}
+
+/*-------------------------------------------------------------------------*/
+
+/*
+ * Some OHCI controllers are known to lose track of completed TDs.  They
+ * don't add the TDs to the hardware done queue, which means we never see
+ * them as being completed.
+ *
+ * This watchdog routine checks for such problems.  Without some way to
+ * tell when those TDs have completed, we would never take their EDs off
+ * the unlink list.  As a result, URBs could never be dequeued and
+ * endpoints could never be released.
+ */
+static void io_watchdog_func(unsigned long _ohci)
+{
+	struct ohci_hcd	*ohci = (struct ohci_hcd *) _ohci;
+	bool		takeback_all_pending = false;
+	u32		status;
+	u32		head;
+	struct ed	*ed;
+	struct td	*td, *td_start, *td_next;
+	unsigned	frame_no;
+	unsigned long	flags;
+
+	spin_lock_irqsave(&ohci->lock, flags);
+
+	/*
+	 * One way to lose track of completed TDs is if the controller
+	 * never writes back the done queue head.  If it hasn't been
+	 * written back since the last time this function ran and if it
+	 * was non-empty at that time, something is badly wrong with the
+	 * hardware.
+	 */
+	status = ohci_readl(ohci, &ohci->regs->intrstatus);
+	if (!(status & OHCI_INTR_WDH) && ohci->wdh_cnt == ohci->prev_wdh_cnt) {
+		if (ohci->prev_donehead) {
+			ohci_err(ohci, "HcDoneHead not written back; disabled\n");
+ died:
+			usb_hc_died(ohci_to_hcd(ohci));
+			ohci_dump(ohci);
+			ohci_shutdown(ohci_to_hcd(ohci));
+			goto done;
+		} else {
+			/* No write back because the done queue was empty */
+			takeback_all_pending = true;
+		}
+	}
+
+	/* Check every ED which might have pending TDs */
+	list_for_each_entry(ed, &ohci->eds_in_use, in_use_list) {
+		if (ed->pending_td) {
+			if (takeback_all_pending ||
+					OKAY_TO_TAKEBACK(ohci, ed)) {
+				unsigned tmp = hc32_to_cpu(ohci, ed->hwINFO);
+
+				ohci_dbg(ohci, "takeback pending TD for dev %d ep 0x%x\n",
+						0x007f & tmp,
+						(0x000f & (tmp >> 7)) +
+							((tmp & ED_IN) >> 5));
+				add_to_done_list(ohci, ed->pending_td);
+			}
+		}
+
+		/* Starting from the latest pending TD, */
+		td = ed->pending_td;
+
+		/* or the last TD on the done list, */
+		if (!td) {
+			list_for_each_entry(td_next, &ed->td_list, td_list) {
+				if (!td_next->next_dl_td)
+					break;
+				td = td_next;
+			}
+		}
+
+		/* find the last TD processed by the controller. */
+		head = hc32_to_cpu(ohci, ACCESS_ONCE(ed->hwHeadP)) & TD_MASK;
+		td_start = td;
+		td_next = list_prepare_entry(td, &ed->td_list, td_list);
+		list_for_each_entry_continue(td_next, &ed->td_list, td_list) {
+			if (head == (u32) td_next->td_dma)
+				break;
+			td = td_next;	/* head pointer has passed this TD */
+		}
+		if (td != td_start) {
+			/*
+			 * In case a WDH cycle is in progress, we will wait
+			 * for the next two cycles to complete before assuming
+			 * this TD will never get on the done queue.
+			 */
+			ed->takeback_wdh_cnt = ohci->wdh_cnt + 2;
+			ed->pending_td = td;
+		}
+	}
+
+	ohci_work(ohci);
+
+	if (ohci->rh_state == OHCI_RH_RUNNING) {
+
+		/*
+		 * Sometimes a controller just stops working.  We can tell
+		 * by checking that the frame counter has advanced since
+		 * the last time we ran.
+		 *
+		 * But be careful: Some controllers violate the spec by
+		 * stopping their frame counter when no ports are active.
+		 */
+		frame_no = ohci_frame_no(ohci);
+		if (frame_no == ohci->prev_frame_no) {
+			int		active_cnt = 0;
+			int		i;
+			unsigned	tmp;
+
+			for (i = 0; i < ohci->num_ports; ++i) {
+				tmp = roothub_portstatus(ohci, i);
+				/* Enabled and not suspended? */
+				if ((tmp & RH_PS_PES) && !(tmp & RH_PS_PSS))
+					++active_cnt;
+			}
+
+			if (active_cnt > 0) {
+				ohci_err(ohci, "frame counter not updating; disabled\n");
+				goto died;
+			}
+		}
+		if (!list_empty(&ohci->eds_in_use)) {
+			ohci->prev_frame_no = frame_no;
+			ohci->prev_wdh_cnt = ohci->wdh_cnt;
+			ohci->prev_donehead = ohci_readl(ohci,
+					&ohci->regs->donehead);
+			mod_timer(&ohci->io_watchdog,
+					jiffies + IO_WATCHDOG_DELAY);
+		}
+	}
+
+ done:
+	spin_unlock_irqrestore(&ohci->lock, flags);
+}
+
+/* an interrupt happens */
+
+static irqreturn_t ohci_irq (struct usb_hcd *hcd)
+{
+	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
+	struct ohci_regs __iomem *regs = ohci->regs;
+	int			ints;
+
+	/* Read interrupt status (and flush pending writes).  We ignore the
+	 * optimization of checking the LSB of hcca->done_head; it doesn't
+	 * work on all systems (edge triggering for OHCI can be a factor).
+	 */
+	ints = ohci_readl(ohci, &regs->intrstatus);
+
+	/* Check for an all 1's result which is a typical consequence
+	 * of dead, unclocked, or unplugged (CardBus...) devices
+	 */
+	if (ints == ~(u32)0) {
+		ohci->rh_state = OHCI_RH_HALTED;
+		ohci_dbg (ohci, "device removed!\n");
+		usb_hc_died(hcd);
+		return IRQ_HANDLED;
+	}
+
+	/* We only care about interrupts that are enabled */
+	ints &= ohci_readl(ohci, &regs->intrenable);
+
+	/* interrupt for some other device? */
+	if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
+		return IRQ_NOTMINE;
+
+	if (ints & OHCI_INTR_UE) {
+		// e.g. due to PCI Master/Target Abort
+		if (quirk_nec(ohci)) {
+			/* Workaround for a silicon bug in some NEC chips used
+			 * in Apple's PowerBooks. Adapted from Darwin code.
+			 */
+			ohci_err (ohci, "OHCI Unrecoverable Error, scheduling NEC chip restart\n");
+
+			ohci_writel (ohci, OHCI_INTR_UE, &regs->intrdisable);
+
+			schedule_work (&ohci->nec_work);
+		} else {
+			ohci_err (ohci, "OHCI Unrecoverable Error, disabled\n");
+			ohci->rh_state = OHCI_RH_HALTED;
+			usb_hc_died(hcd);
+		}
+
+		ohci_dump(ohci);
+		ohci_usb_reset (ohci);
+	}
+
+	if (ints & OHCI_INTR_RHSC) {
+		ohci_dbg(ohci, "rhsc\n");
+		ohci->next_statechange = jiffies + STATECHANGE_DELAY;
+		ohci_writel(ohci, OHCI_INTR_RD | OHCI_INTR_RHSC,
+				&regs->intrstatus);
+
+		/* NOTE: Vendors didn't always make the same implementation
+		 * choices for RHSC.  Many followed the spec; RHSC triggers
+		 * on an edge, like setting and maybe clearing a port status
+		 * change bit.  With others it's level-triggered, active
+		 * until hub_wq clears all the port status change bits.  We'll
+		 * always disable it here and rely on polling until hub_wq
+		 * re-enables it.
+		 */
+		ohci_writel(ohci, OHCI_INTR_RHSC, &regs->intrdisable);
+		usb_hcd_poll_rh_status(hcd);
+	}
+
+	/* For connect and disconnect events, we expect the controller
+	 * to turn on RHSC along with RD.  But for remote wakeup events
+	 * this might not happen.
+	 */
+	else if (ints & OHCI_INTR_RD) {
+		ohci_dbg(ohci, "resume detect\n");
+		ohci_writel(ohci, OHCI_INTR_RD, &regs->intrstatus);
+		set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+		if (ohci->autostop) {
+			spin_lock (&ohci->lock);
+			ohci_rh_resume (ohci);
+			spin_unlock (&ohci->lock);
+		} else
+			usb_hcd_resume_root_hub(hcd);
+	}
+
+	spin_lock(&ohci->lock);
+	if (ints & OHCI_INTR_WDH)
+		update_done_list(ohci);
+
+	/* could track INTR_SO to reduce available PCI/... bandwidth */
+
+	/* handle any pending URB/ED unlinks, leaving INTR_SF enabled
+	 * when there's still unlinking to be done (next frame).
+	 */
+	ohci_work(ohci);
+	if ((ints & OHCI_INTR_SF) != 0 && !ohci->ed_rm_list
+			&& ohci->rh_state == OHCI_RH_RUNNING)
+		ohci_writel (ohci, OHCI_INTR_SF, &regs->intrdisable);
+
+	if (ohci->rh_state == OHCI_RH_RUNNING) {
+		ohci_writel (ohci, ints, &regs->intrstatus);
+		if (ints & OHCI_INTR_WDH)
+			++ohci->wdh_cnt;
+
+		ohci_writel (ohci, OHCI_INTR_MIE, &regs->intrenable);
+		// flush those writes
+		(void) ohci_readl (ohci, &ohci->regs->control);
+	}
+	spin_unlock(&ohci->lock);
+
+	return IRQ_HANDLED;
+}
+
+/*-------------------------------------------------------------------------*/
+
+static void ohci_stop (struct usb_hcd *hcd)
+{
+	struct ohci_hcd		*ohci = hcd_to_ohci (hcd);
+
+	ohci_dump(ohci);
+
+	if (quirk_nec(ohci))
+		flush_work(&ohci->nec_work);
+	del_timer_sync(&ohci->io_watchdog);
+
+	ohci_writel (ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
+	ohci_usb_reset(ohci);
+	free_irq(hcd->irq, hcd);
+	hcd->irq = 0;
+
+	if (quirk_amdiso(ohci))
+		usb_amd_dev_put();
+
+	remove_debug_files (ohci);
+	ohci_mem_cleanup (ohci);
+	if (ohci->hcca) {
+		dma_free_coherent (hcd->self.controller,
+				sizeof *ohci->hcca,
+				ohci->hcca, ohci->hcca_dma);
+		ohci->hcca = NULL;
+		ohci->hcca_dma = 0;
+	}
+}
+
+/*-------------------------------------------------------------------------*/
+
+#if defined(CONFIG_PM) || defined(CONFIG_PCI)
+
+/* must not be called from interrupt context */
+int ohci_restart(struct ohci_hcd *ohci)
+{
+	int temp;
+	int i;
+	struct urb_priv *priv;
+
+	ohci_init(ohci);
+	spin_lock_irq(&ohci->lock);
+	ohci->rh_state = OHCI_RH_HALTED;
+
+	/* Recycle any "live" eds/tds (and urbs). */
+	if (!list_empty (&ohci->pending))
+		ohci_dbg(ohci, "abort schedule...\n");
+	list_for_each_entry (priv, &ohci->pending, pending) {
+		struct urb	*urb = priv->td[0]->urb;
+		struct ed	*ed = priv->ed;
+
+		switch (ed->state) {
+		case ED_OPER:
+			ed->state = ED_UNLINK;
+			ed->hwINFO |= cpu_to_hc32(ohci, ED_DEQUEUE);
+			ed_deschedule (ohci, ed);
+
+			ed->ed_next = ohci->ed_rm_list;
+			ed->ed_prev = NULL;
+			ohci->ed_rm_list = ed;
+			/* FALLTHROUGH */
+		case ED_UNLINK:
+			break;
+		default:
+			ohci_dbg(ohci, "bogus ed %p state %d\n",
+					ed, ed->state);
+		}
+
+		if (!urb->unlinked)
+			urb->unlinked = -ESHUTDOWN;
+	}
+	ohci_work(ohci);
+	spin_unlock_irq(&ohci->lock);
+
+	/* paranoia, in case that didn't work: */
+
+	/* empty the interrupt branches */
+	for (i = 0; i < NUM_INTS; i++) ohci->load [i] = 0;
+	for (i = 0; i < NUM_INTS; i++) ohci->hcca->int_table [i] = 0;
+
+	/* no EDs to remove */
+	ohci->ed_rm_list = NULL;
+
+	/* empty control and bulk lists */
+	ohci->ed_controltail = NULL;
+	ohci->ed_bulktail    = NULL;
+
+	if ((temp = ohci_run (ohci)) < 0) {
+		ohci_err (ohci, "can't restart, %d\n", temp);
+		return temp;
+	}
+	ohci_dbg(ohci, "restart complete\n");
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ohci_restart);
+
+#endif
+
+#ifdef CONFIG_PM
+
+int ohci_suspend(struct usb_hcd *hcd, bool do_wakeup)
+{
+	struct ohci_hcd	*ohci = hcd_to_ohci (hcd);
+	unsigned long	flags;
+	int		rc = 0;
+
+	/* Disable irq emission and mark HW unaccessible. Use
+	 * the spinlock to properly synchronize with possible pending
+	 * RH suspend or resume activity.
+	 */
+	spin_lock_irqsave (&ohci->lock, flags);
+	ohci_writel(ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable);
+	(void)ohci_readl(ohci, &ohci->regs->intrdisable);
+
+	clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+	spin_unlock_irqrestore (&ohci->lock, flags);
+
+	synchronize_irq(hcd->irq);
+
+	if (do_wakeup && HCD_WAKEUP_PENDING(hcd)) {
+		ohci_resume(hcd, false);
+		rc = -EBUSY;
+	}
+	return rc;
+}
+EXPORT_SYMBOL_GPL(ohci_suspend);
+
+
+int ohci_resume(struct usb_hcd *hcd, bool hibernated)
+{
+	struct ohci_hcd		*ohci = hcd_to_ohci(hcd);
+	int			port;
+	bool			need_reinit = false;
+
+	set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
+
+	/* Make sure resume from hibernation re-enumerates everything */
+	if (hibernated)
+		ohci_usb_reset(ohci);
+
+	/* See if the controller is already running or has been reset */
+	ohci->hc_control = ohci_readl(ohci, &ohci->regs->control);
+	if (ohci->hc_control & (OHCI_CTRL_IR | OHCI_SCHED_ENABLES)) {
+		need_reinit = true;
+	} else {
+		switch (ohci->hc_control & OHCI_CTRL_HCFS) {
+		case OHCI_USB_OPER:
+		case OHCI_USB_RESET:
+			need_reinit = true;
+		}
+	}
+
+	/* If needed, reinitialize and suspend the root hub */
+	if (need_reinit) {
+		spin_lock_irq(&ohci->lock);
+		ohci_rh_resume(ohci);
+		ohci_rh_suspend(ohci, 0);
+		spin_unlock_irq(&ohci->lock);
+	}
+
+	/* Normally just turn on port power and enable interrupts */
+	else {
+		ohci_dbg(ohci, "powerup ports\n");
+		for (port = 0; port < ohci->num_ports; port++)
+			ohci_writel(ohci, RH_PS_PPS,
+					&ohci->regs->roothub.portstatus[port]);
+
+		ohci_writel(ohci, OHCI_INTR_MIE, &ohci->regs->intrenable);
+		ohci_readl(ohci, &ohci->regs->intrenable);
+		msleep(20);
+	}
+
+	usb_hcd_resume_root_hub(hcd);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(ohci_resume);
+
+#endif
+
+/*-------------------------------------------------------------------------*/
+
+/*
+ * Generic structure: This gets copied for platform drivers so that
+ * individual entries can be overridden as needed.
+ */
+
+static const struct hc_driver ohci_hc_driver = {
+	.description =          hcd_name,
+	.product_desc =         "OHCI Host Controller",
+	.hcd_priv_size =        sizeof(struct ohci_hcd),
+
+	/*
+	 * generic hardware linkage
+	*/
+	.irq =                  ohci_irq,
+	.flags =                HCD_MEMORY | HCD_USB11,
+
+	/*
+	* basic lifecycle operations
+	*/
+	.reset =                ohci_setup,
+	.start =                ohci_start,
+	.stop =                 ohci_stop,
+	.shutdown =             ohci_shutdown,
+
+	/*
+	 * managing i/o requests and associated device resources
+	*/
+	.urb_enqueue =          ohci_urb_enqueue,
+	.urb_dequeue =          ohci_urb_dequeue,
+	.endpoint_disable =     ohci_endpoint_disable,
+
+	/*
+	* scheduling support
+	*/
+	.get_frame_number =     ohci_get_frame,
+
+	/*
+	* root hub support
+	*/
+	.hub_status_data =      ohci_hub_status_data,
+	.hub_control =          ohci_hub_control,
+#ifdef CONFIG_PM
+	.bus_suspend =          ohci_bus_suspend,
+	.bus_resume =           ohci_bus_resume,
+#endif
+	.start_port_reset =	ohci_start_port_reset,
+};
+
+void ohci_init_driver(struct hc_driver *drv,
+		const struct ohci_driver_overrides *over)
+{
+	/* Copy the generic table to drv and then apply the overrides */
+	*drv = ohci_hc_driver;
+
+	if (over) {
+		drv->product_desc = over->product_desc;
+		drv->hcd_priv_size += over->extra_priv_size;
+		if (over->reset)
+			drv->reset = over->reset;
+	}
+}
+EXPORT_SYMBOL_GPL(ohci_init_driver);
+
+/*-------------------------------------------------------------------------*/
+
+MODULE_AUTHOR (DRIVER_AUTHOR);
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE ("GPL");
+
+#if defined(CONFIG_ARCH_SA1100) && defined(CONFIG_SA1111)
+#include "ohci-sa1111.c"
+#define SA1111_DRIVER		ohci_hcd_sa1111_driver
+#endif
+
+#ifdef CONFIG_USB_OHCI_HCD_DAVINCI
+#include "ohci-da8xx.c"
+#define DAVINCI_PLATFORM_DRIVER	ohci_hcd_da8xx_driver
+#endif
+
+#ifdef CONFIG_USB_OHCI_HCD_PPC_OF
+#include "ohci-ppc-of.c"
+#define OF_PLATFORM_DRIVER	ohci_hcd_ppc_of_driver
+#endif
+
+#ifdef CONFIG_PPC_PS3
+#include "ohci-ps3.c"
+#define PS3_SYSTEM_BUS_DRIVER	ps3_ohci_driver
+#endif
+
+#ifdef CONFIG_MFD_SM501
+#include "ohci-sm501.c"
+#define SM501_OHCI_DRIVER	ohci_hcd_sm501_driver
+#endif
+
+#ifdef CONFIG_MFD_TC6393XB
+#include "ohci-tmio.c"
+#define TMIO_OHCI_DRIVER	ohci_hcd_tmio_driver
+#endif
+
+#ifdef CONFIG_MACH_JZ4740
+#include "ohci-jz4740.c"
+#define PLATFORM_DRIVER	ohci_hcd_jz4740_driver
+#endif
+
+#ifdef CONFIG_TILE_USB
+#include "ohci-tilegx.c"
+#define PLATFORM_DRIVER		ohci_hcd_tilegx_driver
+#endif
+
+static int __init ohci_hcd_mod_init(void)
+{
+	int retval = 0;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	printk(KERN_INFO "%s: " DRIVER_DESC "\n", hcd_name);
+	pr_debug ("%s: block sizes: ed %Zd td %Zd\n", hcd_name,
+		sizeof (struct ed), sizeof (struct td));
+	set_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
+
+	ohci_debug_root = debugfs_create_dir("ohci", usb_debug_root);
+	if (!ohci_debug_root) {
+		retval = -ENOENT;
+		goto error_debug;
+	}
+
+#ifdef PS3_SYSTEM_BUS_DRIVER
+	retval = ps3_ohci_driver_register(&PS3_SYSTEM_BUS_DRIVER);
+	if (retval < 0)
+		goto error_ps3;
+#endif
+
+#ifdef PLATFORM_DRIVER
+	retval = platform_driver_register(&PLATFORM_DRIVER);
+	if (retval < 0)
+		goto error_platform;
+#endif
+
+#ifdef OF_PLATFORM_DRIVER
+	retval = platform_driver_register(&OF_PLATFORM_DRIVER);
+	if (retval < 0)
+		goto error_of_platform;
+#endif
+
+#ifdef SA1111_DRIVER
+	retval = sa1111_driver_register(&SA1111_DRIVER);
+	if (retval < 0)
+		goto error_sa1111;
+#endif
+
+#ifdef SM501_OHCI_DRIVER
+	retval = platform_driver_register(&SM501_OHCI_DRIVER);
+	if (retval < 0)
+		goto error_sm501;
+#endif
+
+#ifdef TMIO_OHCI_DRIVER
+	retval = platform_driver_register(&TMIO_OHCI_DRIVER);
+	if (retval < 0)
+		goto error_tmio;
+#endif
+
+#ifdef DAVINCI_PLATFORM_DRIVER
+	retval = platform_driver_register(&DAVINCI_PLATFORM_DRIVER);
+	if (retval < 0)
+		goto error_davinci;
+#endif
+
+	return retval;
+
+	/* Error path */
+#ifdef DAVINCI_PLATFORM_DRIVER
+	platform_driver_unregister(&DAVINCI_PLATFORM_DRIVER);
+ error_davinci:
+#endif
+#ifdef TMIO_OHCI_DRIVER
+	platform_driver_unregister(&TMIO_OHCI_DRIVER);
+ error_tmio:
+#endif
+#ifdef SM501_OHCI_DRIVER
+	platform_driver_unregister(&SM501_OHCI_DRIVER);
+ error_sm501:
+#endif
+#ifdef SA1111_DRIVER
+	sa1111_driver_unregister(&SA1111_DRIVER);
+ error_sa1111:
+#endif
+#ifdef OF_PLATFORM_DRIVER
+	platform_driver_unregister(&OF_PLATFORM_DRIVER);
+ error_of_platform:
+#endif
+#ifdef PLATFORM_DRIVER
+	platform_driver_unregister(&PLATFORM_DRIVER);
+ error_platform:
+#endif
+#ifdef PS3_SYSTEM_BUS_DRIVER
+	ps3_ohci_driver_unregister(&PS3_SYSTEM_BUS_DRIVER);
+ error_ps3:
+#endif
+	debugfs_remove(ohci_debug_root);
+	ohci_debug_root = NULL;
+ error_debug:
+
+	clear_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
+	return retval;
+}
+module_init(ohci_hcd_mod_init);
+
+static void __exit ohci_hcd_mod_exit(void)
+{
+#ifdef DAVINCI_PLATFORM_DRIVER
+	platform_driver_unregister(&DAVINCI_PLATFORM_DRIVER);
+#endif
+#ifdef TMIO_OHCI_DRIVER
+	platform_driver_unregister(&TMIO_OHCI_DRIVER);
+#endif
+#ifdef SM501_OHCI_DRIVER
+	platform_driver_unregister(&SM501_OHCI_DRIVER);
+#endif
+#ifdef SA1111_DRIVER
+	sa1111_driver_unregister(&SA1111_DRIVER);
+#endif
+#ifdef OF_PLATFORM_DRIVER
+	platform_driver_unregister(&OF_PLATFORM_DRIVER);
+#endif
+#ifdef PLATFORM_DRIVER
+	platform_driver_unregister(&PLATFORM_DRIVER);
+#endif
+#ifdef PS3_SYSTEM_BUS_DRIVER
+	ps3_ohci_driver_unregister(&PS3_SYSTEM_BUS_DRIVER);
+#endif
+	debugfs_remove(ohci_debug_root);
+	clear_bit(USB_OHCI_LOADED, &usb_hcds_loaded);
+}
+module_exit(ohci_hcd_mod_exit);
+