Linux-libre 4.4-gnupck-4.4-gnu

3 files changed, 50 insertions, 32 deletions

diff --git a/include/linux/pinctrl/devinfo.h b/include/linux/pinctrl/devinfo.h
index 281cb91dd..05082e407 100644
--- a/include/linux/pinctrl/devinfo.h
+++ b/include/linux/pinctrl/devinfo.h
@@ -24,10 +24,14 @@
  * struct dev_pin_info - pin state container for devices
  * @p: pinctrl handle for the containing device
  * @default_state: the default state for the handle, if found
+ * @init_state: the state at probe time, if found
+ * @sleep_state: the state at suspend time, if found
+ * @idle_state: the state at idle (runtime suspend) time, if found
  */
 struct dev_pin_info {
 	struct pinctrl *p;
 	struct pinctrl_state *default_state;
+	struct pinctrl_state *init_state;
 #ifdef CONFIG_PM
 	struct pinctrl_state *sleep_state;
 	struct pinctrl_state *idle_state;
@@ -35,6 +39,7 @@ struct dev_pin_info {
 };
 
 extern int pinctrl_bind_pins(struct device *dev);
+extern int pinctrl_init_done(struct device *dev);
 
 #else
 
@@ -45,5 +50,10 @@ static inline int pinctrl_bind_pins(struct device *dev)
 	return 0;
 }
 
+static inline int pinctrl_init_done(struct device *dev)
+{
+	return 0;
+}
+
 #endif /* CONFIG_PINCTRL */
 #endif /* PINCTRL_DEVINFO_H */
diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index fe65962b2..d921afd5f 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -20,6 +20,11 @@
 
 /**
  * enum pin_config_param - possible pin configuration parameters
+ * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it
+ *	weakly drives the last value on a tristate bus, also known as a "bus
+ *	holder", "bus keeper" or "repeater". This allows another device on the
+ *	bus to change the value by driving the bus high or low and switching to
+ *	tristate. The argument is ignored.
  * @PIN_CONFIG_BIAS_DISABLE: disable any pin bias on the pin, a
  *	transition from say pull-up to pull-down implies that you disable
  *	pull-up in the process, this setting disables all biasing.
@@ -29,14 +34,6 @@
  *	if for example some other pin is going to drive the signal connected
  *	to it for a while. Pins used for input are usually always high
  *	impedance.
- * @PIN_CONFIG_BIAS_BUS_HOLD: the pin will be set to weakly latch so that it
- *	weakly drives the last value on a tristate bus, also known as a "bus
- *	holder", "bus keeper" or "repeater". This allows another device on the
- *	bus to change the value by driving the bus high or low and switching to
- *	tristate. The argument is ignored.
- * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
- *	impedance to VDD). If the argument is != 0 pull-up is enabled,
- *	if it is 0, pull-up is total, i.e. the pin is connected to VDD.
  * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high
  *	impedance to GROUND). If the argument is != 0 pull-down is enabled,
  *	if it is 0, pull-down is total, i.e. the pin is connected to GROUND.
@@ -48,10 +45,9 @@
  *	If the argument is != 0 pull up/down is enabled, if it is 0, the
  *	configuration is ignored. The proper way to disable it is to use
  *	@PIN_CONFIG_BIAS_DISABLE.
- * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and
- *	low, this is the most typical case and is typically achieved with two
- *	active transistors on the output. Setting this config will enable
- *	push-pull mode, the argument is ignored.
+ * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high
+ *	impedance to VDD). If the argument is != 0 pull-up is enabled,
+ *	if it is 0, pull-up is total, i.e. the pin is connected to VDD.
  * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open
  *	collector) which means it is usually wired with other output ports
  *	which are then pulled up with an external resistor. Setting this
@@ -59,28 +55,26 @@
  * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source
  *	(open emitter). Setting this config will enable open source mode, the
  *	argument is ignored.
+ * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and
+ *	low, this is the most typical case and is typically achieved with two
+ *	active transistors on the output. Setting this config will enable
+ *	push-pull mode, the argument is ignored.
  * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current
  *	passed as argument. The argument is in mA.
+ * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode,
+ *	which means it will wait for signals to settle when reading inputs. The
+ *	argument gives the debounce time in usecs. Setting the
+ *	argument to zero turns debouncing off.
  * @PIN_CONFIG_INPUT_ENABLE: enable the pin's input.  Note that this does not
  *	affect the pin's ability to drive output.  1 enables input, 0 disables
  *	input.
- * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin.
- *      If the argument != 0, schmitt-trigger mode is enabled. If it's 0,
- *      schmitt-trigger mode is disabled.
  * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in
  *	schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis,
  *	the threshold value is given on a custom format as argument when
  *	setting pins to this mode.
- * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode,
- *	which means it will wait for signals to settle when reading inputs. The
- *	argument gives the debounce time in usecs. Setting the
- *	argument to zero turns debouncing off.
- * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
- *	supplies, the argument to this parameter (on a custom format) tells
- *	the driver which alternative power source to use.
- * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
- *	this parameter (on a custom format) tells the driver which alternative
- *	slew rate to use.
+ * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin.
+ *      If the argument != 0, schmitt-trigger mode is enabled. If it's 0,
+ *      schmitt-trigger mode is disabled.
  * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power
  *	operation, if several modes of operation are supported these can be
  *	passed in the argument on a custom form, else just use argument 1
@@ -89,29 +83,35 @@
  *	1 to indicate high level, argument 0 to indicate low level. (Please
  *	see Documentation/pinctrl.txt, section "GPIO mode pitfalls" for a
  *	discussion around this parameter.)
+ * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
+ *	supplies, the argument to this parameter (on a custom format) tells
+ *	the driver which alternative power source to use.
+ * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
+ *	this parameter (on a custom format) tells the driver which alternative
+ *	slew rate to use.
  * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
  *	you need to pass in custom configurations to the pin controller, use
  *	PIN_CONFIG_END+1 as the base offset.
  */
 enum pin_config_param {
+	PIN_CONFIG_BIAS_BUS_HOLD,
 	PIN_CONFIG_BIAS_DISABLE,
 	PIN_CONFIG_BIAS_HIGH_IMPEDANCE,
-	PIN_CONFIG_BIAS_BUS_HOLD,
-	PIN_CONFIG_BIAS_PULL_UP,
 	PIN_CONFIG_BIAS_PULL_DOWN,
 	PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
-	PIN_CONFIG_DRIVE_PUSH_PULL,
+	PIN_CONFIG_BIAS_PULL_UP,
 	PIN_CONFIG_DRIVE_OPEN_DRAIN,
 	PIN_CONFIG_DRIVE_OPEN_SOURCE,
+	PIN_CONFIG_DRIVE_PUSH_PULL,
 	PIN_CONFIG_DRIVE_STRENGTH,
+	PIN_CONFIG_INPUT_DEBOUNCE,
 	PIN_CONFIG_INPUT_ENABLE,
-	PIN_CONFIG_INPUT_SCHMITT_ENABLE,
 	PIN_CONFIG_INPUT_SCHMITT,
-	PIN_CONFIG_INPUT_DEBOUNCE,
-	PIN_CONFIG_POWER_SOURCE,
-	PIN_CONFIG_SLEW_RATE,
+	PIN_CONFIG_INPUT_SCHMITT_ENABLE,
 	PIN_CONFIG_LOW_POWER_MODE,
 	PIN_CONFIG_OUTPUT,
+	PIN_CONFIG_POWER_SOURCE,
+	PIN_CONFIG_SLEW_RATE,
 	PIN_CONFIG_END = 0x7FFF,
 };
 
diff --git a/include/linux/pinctrl/pinctrl-state.h b/include/linux/pinctrl/pinctrl-state.h
index b5919f8e6..230735193 100644
--- a/include/linux/pinctrl/pinctrl-state.h
+++ b/include/linux/pinctrl/pinctrl-state.h
@@ -9,6 +9,13 @@
  *	hogs to configure muxing and pins at boot, and also as a state
  *	to go into when returning from sleep and idle in
  *	.pm_runtime_resume() or ordinary .resume() for example.
+ * @PINCTRL_STATE_INIT: normally the pinctrl will be set to "default"
+ *	before the driver's probe() function is called.  There are some
+ *	drivers where that is not appropriate becausing doing so would
+ *	glitch the pins.  In those cases you can add an "init" pinctrl
+ *	which is the state of the pins before drive probe.  After probe
+ *	if the pins are still in "init" state they'll be moved to
+ *	"default".
  * @PINCTRL_STATE_IDLE: the state the pinctrl handle shall be put into
  *	when the pins are idle. This is a state where the system is relaxed
  *	but not fully sleeping - some power may be on but clocks gated for
@@ -20,5 +27,6 @@
  *	ordinary .suspend() function.
  */
 #define PINCTRL_STATE_DEFAULT "default"
+#define PINCTRL_STATE_INIT "init"
 #define PINCTRL_STATE_IDLE "idle"
 #define PINCTRL_STATE_SLEEP "sleep"