Linux-libre 4.2-gnu

3 files changed, 24 insertions, 0 deletions

diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index fffa688ac..4db9fbe48 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -91,6 +91,7 @@ struct regulator_linear_range {
  * @set_current_limit: Configure a limit for a current-limited regulator.
  *                     The driver should select the current closest to max_uA.
  * @get_current_limit: Get the configured limit for a current-limited regulator.
+ * @set_input_current_limit: Configure an input limit.
  *
  * @set_mode: Set the configured operating mode for the regulator.
  * @get_mode: Get the configured operating mode for the regulator.
@@ -111,6 +112,7 @@ struct regulator_linear_range {
  *               to stabilise after being set to a new value, in microseconds.
  *               The function provides the from and to voltage selector, the
  *               function should return the worst case.
+ * @set_soft_start: Enable soft start for the regulator.
  *
  * @set_suspend_voltage: Set the voltage for the regulator when the system
  *                       is suspended.
@@ -121,6 +123,9 @@ struct regulator_linear_range {
  * @set_suspend_mode: Set the operating mode for the regulator when the
  *                    system is suspended.
  *
+ * @set_pull_down: Configure the regulator to pull down when the regulator
+ *		   is disabled.
+ *
  * This struct describes regulator operations which can be implemented by
  * regulator chip drivers.
  */
@@ -142,6 +147,8 @@ struct regulator_ops {
 				 int min_uA, int max_uA);
 	int (*get_current_limit) (struct regulator_dev *);
 
+	int (*set_input_current_limit) (struct regulator_dev *, int lim_uA);
+
 	/* enable/disable regulator */
 	int (*enable) (struct regulator_dev *);
 	int (*disable) (struct regulator_dev *);
@@ -158,6 +165,8 @@ struct regulator_ops {
 				     unsigned int old_selector,
 				     unsigned int new_selector);
 
+	int (*set_soft_start) (struct regulator_dev *);
+
 	/* report regulator status ... most other accessors report
 	 * control inputs, this reports results of combining inputs
 	 * from Linux (and other sources) with the actual load.
@@ -187,6 +196,8 @@ struct regulator_ops {
 
 	/* set regulator suspend operating mode (defined in consumer.h) */
 	int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode);
+
+	int (*set_pull_down) (struct regulator_dev *);
 };
 
 /*
diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h
index b07562e08..b11be1260 100644
--- a/include/linux/regulator/machine.h
+++ b/include/linux/regulator/machine.h
@@ -75,6 +75,8 @@ struct regulator_state {
  *
  * @min_uA: Smallest current consumers may set.
  * @max_uA: Largest current consumers may set.
+ * @ilim_uA: Maximum input current.
+ * @system_load: Load that isn't captured by any consumer requests.
  *
  * @valid_modes_mask: Mask of modes which may be configured by consumers.
  * @valid_ops_mask: Operations which may be performed by consumers.
@@ -86,6 +88,8 @@ struct regulator_state {
  *           applied.
  * @apply_uV: Apply the voltage constraint when initialising.
  * @ramp_disable: Disable ramp delay when initialising or when setting voltage.
+ * @soft_start: Enable soft start so that voltage ramps slowly.
+ * @pull_down: Enable pull down when regulator is disabled.
  *
  * @input_uV: Input voltage for regulator when supplied by another regulator.
  *
@@ -111,6 +115,9 @@ struct regulation_constraints {
 	/* current output range (inclusive) - for current control */
 	int min_uA;
 	int max_uA;
+	int ilim_uA;
+
+	int system_load;
 
 	/* valid regulator operating modes for this machine */
 	unsigned int valid_modes_mask;
@@ -138,6 +145,8 @@ struct regulation_constraints {
 	unsigned boot_on:1;	/* bootloader/firmware enabled regulator */
 	unsigned apply_uV:1;	/* apply uV constraint if min == max */
 	unsigned ramp_disable:1; /* disable ramp delay */
+	unsigned soft_start:1;	/* ramp voltage slowly */
+	unsigned pull_down:1;	/* pull down resistor when regulator off */
 };
 
 /**
diff --git a/include/linux/regulator/max8973-regulator.h b/include/linux/regulator/max8973-regulator.h
index f8acc052e..f6a8a16a0 100644
--- a/include/linux/regulator/max8973-regulator.h
+++ b/include/linux/regulator/max8973-regulator.h
@@ -58,6 +58,9 @@
  *		control signal from EN input pin. If it is false then
  *		voltage output will be enabled/disabled through EN bit of
  *		device register.
+ * @enable_gpio: Enable GPIO. If EN pin is controlled through GPIO from host
+ *		then GPIO number can be provided. If no GPIO controlled then
+ *		it should be -1.
  * @dvs_gpio: GPIO for dvs. It should be -1 if this is tied with fixed logic.
  * @dvs_def_state: Default state of dvs. 1 if it is high else 0.
  */
@@ -65,6 +68,7 @@ struct max8973_regulator_platform_data {
 	struct regulator_init_data *reg_init_data;
 	unsigned long control_flags;
 	bool enable_ext_control;
+	int enable_gpio;
 	int dvs_gpio;
 	unsigned dvs_def_state:1;
 };