summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/dma
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/dma')
-rw-r--r--Documentation/devicetree/bindings/dma/adi,axi-dmac.txt61
-rw-r--r--Documentation/devicetree/bindings/dma/arm-pl08x.txt54
-rw-r--r--Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt54
-rw-r--r--Documentation/devicetree/bindings/dma/mv-xor.txt10
-rw-r--r--Documentation/devicetree/bindings/dma/sun4i-dma.txt46
-rw-r--r--Documentation/devicetree/bindings/dma/zxdma.txt38
6 files changed, 257 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt b/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
new file mode 100644
index 000000000..47cb1d14b
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
@@ -0,0 +1,61 @@
+Analog Device AXI-DMAC DMA controller
+
+Required properties:
+ - compatible: Must be "adi,axi-dmac-1.00.a".
+ - reg: Specification for the controllers memory mapped register map.
+ - interrupts: Specification for the controllers interrupt.
+ - clocks: Phandle and specifier to the controllers AXI interface clock
+ - #dma-cells: Must be 1.
+
+Required sub-nodes:
+ - adi,channels: This sub-node must contain a sub-node for each DMA channel. For
+ the channel sub-nodes the following bindings apply. They must match the
+ configuration options of the peripheral as it was instantiated.
+
+Required properties for adi,channels sub-node:
+ - #size-cells: Must be 0
+ - #address-cells: Must be 1
+
+Required channel sub-node properties:
+ - reg: Which channel this node refers to.
+ - adi,length-width: Width of the DMA transfer length register.
+ - adi,source-bus-width,
+ adi,destination-bus-width: Width of the source or destination bus in bits.
+ - adi,source-bus-type,
+ adi,destination-bus-type: Type of the source or destination bus. Must be one
+ of the following:
+ 0 (AXI_DMAC_TYPE_AXI_MM): Memory mapped AXI interface
+ 1 (AXI_DMAC_TYPE_AXI_STREAM): Streaming AXI interface
+ 2 (AXI_DMAC_TYPE_AXI_FIFO): FIFO interface
+
+Optional channel properties:
+ - adi,cyclic: Must be set if the channel supports hardware cyclic DMA
+ transfers.
+ - adi,2d: Must be set if the channel supports hardware 2D DMA transfers.
+
+DMA clients connected to the AXI-DMAC DMA controller must use the format
+described in the dma.txt file using a one-cell specifier. The value of the
+specifier refers to the DMA channel index.
+
+Example:
+
+dma: dma@7c420000 {
+ compatible = "adi,axi-dmac-1.00.a";
+ reg = <0x7c420000 0x10000>;
+ interrupts = <0 57 0>;
+ clocks = <&clkc 16>;
+ #dma-cells = <1>;
+
+ adi,channels {
+ #size-cells = <0>;
+ #address-cells = <1>;
+
+ dma-channel@0 {
+ reg = <0>;
+ adi,source-bus-width = <32>;
+ adi,source-bus-type = <ADI_AXI_DMAC_TYPE_MM_AXI>;
+ adi,destination-bus-width = <64>;
+ adi,destination-bus-type = <ADI_AXI_DMAC_TYPE_FIFO>;
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/dma/arm-pl08x.txt b/Documentation/devicetree/bindings/dma/arm-pl08x.txt
new file mode 100644
index 000000000..8a0097a02
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/arm-pl08x.txt
@@ -0,0 +1,54 @@
+* ARM PrimeCells PL080 and PL081 and derivatives DMA controller
+
+Required properties:
+- compatible: "arm,pl080", "arm,primecell";
+ "arm,pl081", "arm,primecell";
+- reg: Address range of the PL08x registers
+- interrupt: The PL08x interrupt number
+- clocks: The clock running the IP core clock
+- clock-names: Must contain "apb_pclk"
+- lli-bus-interface-ahb1: if AHB master 1 is eligible for fetching LLIs
+- lli-bus-interface-ahb2: if AHB master 2 is eligible for fetching LLIs
+- mem-bus-interface-ahb1: if AHB master 1 is eligible for fetching memory contents
+- mem-bus-interface-ahb2: if AHB master 2 is eligible for fetching memory contents
+- #dma-cells: must be <2>. First cell should contain the DMA request,
+ second cell should contain either 1 or 2 depending on
+ which AHB master that is used.
+
+Optional properties:
+- dma-channels: contains the total number of DMA channels supported by the DMAC
+- dma-requests: contains the total number of DMA requests supported by the DMAC
+- memcpy-burst-size: the size of the bursts for memcpy: 1, 4, 8, 16, 32
+ 64, 128 or 256 bytes are legal values
+- memcpy-bus-width: the bus width used for memcpy: 8, 16 or 32 are legal
+ values
+
+Clients
+Required properties:
+- dmas: List of DMA controller phandle, request channel and AHB master id
+- dma-names: Names of the aforementioned requested channels
+
+Example:
+
+dmac0: dma-controller@10130000 {
+ compatible = "arm,pl080", "arm,primecell";
+ reg = <0x10130000 0x1000>;
+ interrupt-parent = <&vica>;
+ interrupts = <15>;
+ clocks = <&hclkdma0>;
+ clock-names = "apb_pclk";
+ lli-bus-interface-ahb1;
+ lli-bus-interface-ahb2;
+ mem-bus-interface-ahb2;
+ memcpy-burst-size = <256>;
+ memcpy-bus-width = <32>;
+ #dma-cells = <2>;
+};
+
+device@40008000 {
+ ...
+ dmas = <&dmac0 0 2
+ &dmac0 1 2>;
+ dma-names = "tx", "rx";
+ ...
+};
diff --git a/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt b/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
new file mode 100644
index 000000000..87740adb2
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt
@@ -0,0 +1,54 @@
+NXP LPC18xx/43xx DMA MUX (DMA request router)
+
+Required properties:
+- compatible: "nxp,lpc1850-dmamux"
+- reg: Memory map for accessing module
+- #dma-cells: Should be set to <3>.
+ * 1st cell contain the master dma request signal
+ * 2nd cell contain the mux value (0-3) for the peripheral
+ * 3rd cell contain either 1 or 2 depending on the AHB
+ master used.
+- dma-requests: Number of DMA requests for the mux
+- dma-masters: phandle pointing to the DMA controller
+
+The DMA controller node need to have the following poroperties:
+- dma-requests: Number of DMA requests the controller can handle
+
+Example:
+
+dmac: dma@40002000 {
+ compatible = "nxp,lpc1850-gpdma", "arm,pl080", "arm,primecell";
+ arm,primecell-periphid = <0x00041080>;
+ reg = <0x40002000 0x1000>;
+ interrupts = <2>;
+ clocks = <&ccu1 CLK_CPU_DMA>;
+ clock-names = "apb_pclk";
+ #dma-cells = <2>;
+ dma-channels = <8>;
+ dma-requests = <16>;
+ lli-bus-interface-ahb1;
+ lli-bus-interface-ahb2;
+ mem-bus-interface-ahb1;
+ mem-bus-interface-ahb2;
+ memcpy-burst-size = <256>;
+ memcpy-bus-width = <32>;
+};
+
+dmamux: dma-mux {
+ compatible = "nxp,lpc1850-dmamux";
+ #dma-cells = <3>;
+ dma-requests = <64>;
+ dma-masters = <&dmac>;
+};
+
+uart0: serial@40081000 {
+ compatible = "nxp,lpc1850-uart", "ns16550a";
+ reg = <0x40081000 0x1000>;
+ reg-shift = <2>;
+ interrupts = <24>;
+ clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>;
+ clock-names = "uartclk", "reg";
+ dmas = <&dmamux 1 1 2
+ &dmamux 2 1 2>;
+ dma-names = "tx", "rx";
+};
diff --git a/Documentation/devicetree/bindings/dma/mv-xor.txt b/Documentation/devicetree/bindings/dma/mv-xor.txt
index cc29c3526..276ef815e 100644
--- a/Documentation/devicetree/bindings/dma/mv-xor.txt
+++ b/Documentation/devicetree/bindings/dma/mv-xor.txt
@@ -12,10 +12,13 @@ XOR engine has. Those sub-nodes have the following required
properties:
- interrupts: interrupt of the XOR channel
-And the following optional properties:
+The sub-nodes used to contain one or several of the following
+properties, but they are now deprecated:
- dmacap,memcpy to indicate that the XOR channel is capable of memcpy operations
- dmacap,memset to indicate that the XOR channel is capable of memset operations
- dmacap,xor to indicate that the XOR channel is capable of xor operations
+- dmacap,interrupt to indicate that the XOR channel is capable of
+ generating interrupts
Example:
@@ -28,13 +31,8 @@ xor@d0060900 {
xor00 {
interrupts = <51>;
- dmacap,memcpy;
- dmacap,xor;
};
xor01 {
interrupts = <52>;
- dmacap,memcpy;
- dmacap,xor;
- dmacap,memset;
};
};
diff --git a/Documentation/devicetree/bindings/dma/sun4i-dma.txt b/Documentation/devicetree/bindings/dma/sun4i-dma.txt
new file mode 100644
index 000000000..f1634a27a
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/sun4i-dma.txt
@@ -0,0 +1,46 @@
+Allwinner A10 DMA Controller
+
+This driver follows the generic DMA bindings defined in dma.txt.
+
+Required properties:
+
+- compatible: Must be "allwinner,sun4i-a10-dma"
+- reg: Should contain the registers base address and length
+- interrupts: Should contain a reference to the interrupt used by this device
+- clocks: Should contain a reference to the parent AHB clock
+- #dma-cells : Should be 2, first cell denoting normal or dedicated dma,
+ second cell holding the request line number.
+
+Example:
+ dma: dma-controller@01c02000 {
+ compatible = "allwinner,sun4i-a10-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <27>;
+ clocks = <&ahb_gates 6>;
+ #dma-cells = <2>;
+ };
+
+Clients:
+
+DMA clients connected to the Allwinner A10 DMA controller must use the
+format described in the dma.txt file, using a three-cell specifier for
+each channel: a phandle plus two integer cells.
+The three cells in order are:
+
+1. A phandle pointing to the DMA controller.
+2. Whether it is using normal (0) or dedicated (1) channels
+3. The port ID as specified in the datasheet
+
+Example:
+ spi2: spi@01c17000 {
+ compatible = "allwinner,sun4i-a10-spi";
+ reg = <0x01c17000 0x1000>;
+ interrupts = <0 12 4>;
+ clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 1 29>, <&dma 1 28>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
diff --git a/Documentation/devicetree/bindings/dma/zxdma.txt b/Documentation/devicetree/bindings/dma/zxdma.txt
new file mode 100644
index 000000000..3207ceb04
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/zxdma.txt
@@ -0,0 +1,38 @@
+* ZTE ZX296702 DMA controller
+
+Required properties:
+- compatible: Should be "zte,zx296702-dma"
+- reg: Should contain DMA registers location and length.
+- interrupts: Should contain one interrupt shared by all channel
+- #dma-cells: see dma.txt, should be 1, para number
+- dma-channels: physical channels supported
+- dma-requests: virtual channels supported, each virtual channel
+ have specific request line
+- clocks: clock required
+
+Example:
+
+Controller:
+ dma: dma-controller@0x09c00000{
+ compatible = "zte,zx296702-dma";
+ reg = <0x09c00000 0x1000>;
+ clocks = <&topclk ZX296702_DMA_ACLK>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ dma-channels = <24>;
+ dma-requests = <24>;
+ };
+
+Client:
+Use specific request line passing from dmax
+For example, spdif0 tx channel request line is 4
+ spdif0: spdif0@0b004000 {
+ #sound-dai-cells = <0>;
+ compatible = "zte,zx296702-spdif";
+ reg = <0x0b004000 0x1000>;
+ clocks = <&lsp0clk ZX296702_SPDIF0_DIV>;
+ clock-names = "tx";
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma 4>;
+ dma-names = "tx";
+ }