diff options
Diffstat (limited to 'Documentation/devicetree/bindings/i2c')
55 files changed, 2228 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt new file mode 100644 index 000000000..e9de37567 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt @@ -0,0 +1,20 @@ +Broadcom BCM2835 I2C controller + +Required properties: +- compatible : Should be "brcm,bcm2835-i2c". +- reg: Should contain register location and length. +- interrupts: Should contain interrupt. +- clocks : The clock feeding the I2C controller. + +Recommended properties: +- clock-frequency : desired I2C bus clock frequency in Hz. + +Example: + +i2c@20205000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e205000 0x1000>; + interrupts = <2 21>; + clocks = <&clk_i2c>; + clock-frequency = <100000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt new file mode 100644 index 000000000..81f982ccc --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt @@ -0,0 +1,37 @@ +Broadcom iProc I2C controller + +Required properties: + +- compatible: + Must be "brcm,iproc-i2c" + +- reg: + Define the base and range of the I/O address space that contain the iProc + I2C controller registers + +- interrupts: + Should contain the I2C interrupt + +- clock-frequency: + This is the I2C bus clock. Need to be either 100000 or 400000 + +- #address-cells: + Always 1 (for I2C addresses) + +- #size-cells: + Always 0 + +Example: + i2c0: i2c@18008000 { + compatible = "brcm,iproc-i2c"; + reg = <0x18008000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>; + clock-frequency = <100000>; + + codec: wm8750@1a { + compatible = "wlf,wm8750"; + reg = <0x1a>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/brcm,kona-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,kona-i2c.txt new file mode 100644 index 000000000..1b87b741f --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/brcm,kona-i2c.txt @@ -0,0 +1,35 @@ +Broadcom Kona Family I2C +========================= + +This I2C controller is used in the following Broadcom SoCs: + + BCM11130 + BCM11140 + BCM11351 + BCM28145 + BCM28155 + +Required Properties +------------------- +- compatible: "brcm,bcm11351-i2c", "brcm,kona-i2c" +- reg: Physical base address and length of controller registers +- interrupts: The interrupt number used by the controller +- clocks: clock specifier for the kona i2c external clock +- clock-frequency: The I2C bus frequency in Hz +- #address-cells: Should be <1> +- #size-cells: Should be <0> + +Refer to clocks/clock-bindings.txt for generic clock consumer +properties. + +Example: + +i2c@3e016000 { + compatible = "brcm,bcm11351-i2c","brcm,kona-i2c"; + reg = <0x3e016000 0x80>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&bsc1_clk>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt new file mode 100644 index 000000000..bfeabb843 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt @@ -0,0 +1,86 @@ +GPIO-based I2C Arbitration Using a Challenge & Response Mechanism +================================================================= +This uses GPIO lines and a challenge & response mechanism to arbitrate who is +the master of an I2C bus in a multimaster situation. + +In many cases using GPIOs to arbitrate is not needed and a design can use +the standard I2C multi-master rules. Using GPIOs is generally useful in +the case where there is a device on the bus that has errata and/or bugs +that makes standard multimaster mode not feasible. + +Note that this scheme works well enough but has some downsides: +* It is nonstandard (not using standard I2C multimaster) +* Having two masters on a bus in general makes it relatively hard to debug + problems (hard to tell if i2c issues were caused by one master, another, or + some device on the bus). + + +Algorithm: + +All masters on the bus have a 'bus claim' line which is an output that the +others can see. These are all active low with pull-ups enabled. We'll +describe these lines as: + +- OUR_CLAIM: output from us signaling to other hosts that we want the bus +- THEIR_CLAIMS: output from others signaling that they want the bus + +The basic algorithm is to assert your line when you want the bus, then make +sure that the other side doesn't want it also. A detailed explanation is best +done with an example. + +Let's say we want to claim the bus. We: +1. Assert OUR_CLAIM. +2. Waits a little bit for the other sides to notice (slew time, say 10 + microseconds). +3. Check THEIR_CLAIMS. If none are asserted then the we have the bus and we are + done. +4. Otherwise, wait for a few milliseconds and see if THEIR_CLAIMS are released. +5. If not, back off, release the claim and wait for a few more milliseconds. +6. Go back to 1 (until retry time has expired). + + +Required properties: +- compatible: i2c-arb-gpio-challenge +- our-claim-gpio: The GPIO that we use to claim the bus. +- their-claim-gpios: The GPIOs that the other sides use to claim the bus. + Note that some implementations may only support a single other master. +- Standard I2C mux properties. See mux.txt in this directory. +- Single I2C child bus node at reg 0. See mux.txt in this directory. + +Optional properties: +- slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us. +- wait-retry-us: we'll attempt another claim after this many microseconds. + Default is 3000 us. +- wait-free-us: we'll give up after this many microseconds. Default is 50000 us. + + +Example: + i2c@12CA0000 { + compatible = "acme,some-i2c-device"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c-arbitrator { + compatible = "i2c-arb-gpio-challenge"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&{/i2c@12CA0000}>; + + our-claim-gpio = <&gpf0 3 1>; + their-claim-gpios = <&gpe0 4 1>; + slew-delay-us = <10>; + wait-retry-us = <3000>; + wait-free-us = <50000>; + + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@52 { + // Normal I2C device + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-at91.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt new file mode 100644 index 000000000..388f0a275 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt @@ -0,0 +1,34 @@ +I2C for Atmel platforms + +Required properties : +- compatible : Must be "atmel,at91rm9200-i2c", "atmel,at91sam9261-i2c", + "atmel,at91sam9260-i2c", "atmel,at91sam9g20-i2c", "atmel,at91sam9g10-i2c" + or "atmel,at91sam9x5-i2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- #address-cells = <1>; +- #size-cells = <0>; +- clocks: phandles to input clocks. + +Optional properties: +- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000 +- Child nodes conforming to i2c bus binding + +Examples : + +i2c0: i2c@fff84000 { + compatible = "atmel,at91sam9g20-i2c"; + reg = <0xfff84000 0x100>; + interrupts = <12 4 6>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&twi0_clk>; + clock-frequency = <400000>; + + 24c512@50 { + compatible = "24c512"; + reg = <0x50>; + pagesize = <128>; + } +} diff --git a/Documentation/devicetree/bindings/i2c/i2c-axxia.txt b/Documentation/devicetree/bindings/i2c/i2c-axxia.txt new file mode 100644 index 000000000..2296d782b --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-axxia.txt @@ -0,0 +1,30 @@ +LSI Axxia I2C + +Required properties : +- compatible : Must be "lsi,api2c" +- reg : Offset and length of the register set for the device +- interrupts : the interrupt specifier +- #address-cells : Must be <1>; +- #size-cells : Must be <0>; +- clock-names : Must contain "i2c". +- clocks: Must contain an entry for each name in clock-names. See the common + clock bindings. + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. + +Example : + +i2c@02010084000 { + compatible = "lsi,api2c"; + device_type = "i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x20 0x10084000 0x00 0x1000>; + interrupts = <0 19 4>; + clocks = <&clk_per>; + clock-names = "i2c"; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-cadence.txt b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt new file mode 100644 index 000000000..7cb0b5608 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt @@ -0,0 +1,24 @@ +Binding for the Cadence I2C controller + +Required properties: + - reg: Physical base address and size of the controller's register area. + - compatible: Compatibility string. Must be 'cdns,i2c-r1p10'. + - clocks: Input clock specifier. Refer to common clock bindings. + - interrupts: Interrupt specifier. Refer to interrupt bindings. + - #address-cells: Should be 1. + - #size-cells: Should be 0. + +Optional properties: + - clock-frequency: Desired operating frequency, in Hz, of the bus. + - clock-names: Input clock name, should be 'pclk'. + +Example: + i2c@e0004000 { + compatible = "cdns,i2c-r1p10"; + clocks = <&clkc 38>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xe0004000 0x1000>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt new file mode 100644 index 000000000..8ce9cd285 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt @@ -0,0 +1,27 @@ +Device tree bindings for i2c-cbus-gpio driver + +Required properties: + - compatible = "i2c-cbus-gpio"; + - gpios: clk, dat, sel + - #address-cells = <1>; + - #size-cells = <0>; + +Optional properties: + - child nodes conforming to i2c bus binding + +Example: + +i2c@0 { + compatible = "i2c-cbus-gpio"; + gpios = <&gpio 66 0 /* clk */ + &gpio 65 0 /* dat */ + &gpio 64 0 /* sel */ + >; + #address-cells = <1>; + #size-cells = <0>; + + retu-mfd: retu@1 { + compatible = "retu-mfd"; + reg = <0x1>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt b/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt new file mode 100644 index 000000000..898f030eb --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt @@ -0,0 +1,39 @@ +I2C bus that tunnels through the ChromeOS EC (cros-ec) +====================================================== +On some ChromeOS board designs we've got a connection to the EC (embedded +controller) but no direct connection to some devices on the other side of +the EC (like a battery and PMIC). To get access to those devices we need +to tunnel our i2c commands through the EC. + +The node for this device should be under a cros-ec node like google,cros-ec-spi +or google,cros-ec-i2c. + + +Required properties: +- compatible: google,cros-ec-i2c-tunnel +- google,remote-bus: The EC bus we'd like to talk to. + +Optional child nodes: +- One node per I2C device connected to the tunnelled I2C bus. + + +Example: + cros-ec@0 { + compatible = "google,cros-ec-spi"; + + ... + + i2c-tunnel { + compatible = "google,cros-ec-i2c-tunnel"; + #address-cells = <1>; + #size-cells = <0>; + + google,remote-bus = <0>; + + battery: sbs-battery@b { + compatible = "sbs,sbs-battery"; + reg = <0xb>; + sbs,poll-retry-count = <1>; + }; + }; + } diff --git a/Documentation/devicetree/bindings/i2c/i2c-davinci.txt b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt new file mode 100644 index 000000000..a4e1cbc81 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt @@ -0,0 +1,31 @@ +* Texas Instruments Davinci I2C + +This file provides information, what the device node for the +davinci i2c interface contain. + +Required properties: +- compatible: "ti,davinci-i2c"; +- reg : Offset and length of the register set for the device + +Recommended properties : +- interrupts : standard interrupt property. +- clock-frequency : desired I2C bus clock frequency in Hz. +- ti,has-pfunc: boolean; if defined, it indicates that SoC supports PFUNC + registers. PFUNC registers allow to switch I2C pins to function as + GPIOs, so they can by toggled manually. + +Example (enbw_cmc board): + i2c@1c22000 { + compatible = "ti,davinci-i2c"; + reg = <0x22000 0x1000>; + clock-frequency = <100000>; + interrupts = <15>; + interrupt-parent = <&intc>; + #address-cells = <1>; + #size-cells = <0>; + + dtt@48 { + compatible = "national,lm75"; + reg = <0x48>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt new file mode 100644 index 000000000..fee26dc3e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt @@ -0,0 +1,45 @@ +* Synopsys DesignWare I2C + +Required properties : + + - compatible : should be "snps,designware-i2c" + - reg : Offset and length of the register set for the device + - interrupts : <IRQ> where IRQ is the interrupt number. + +Recommended properties : + + - clock-frequency : desired I2C bus clock frequency in Hz. + +Optional properties : + - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds. + This option is only supported in hardware blocks version 1.11a or newer. + + - i2c-scl-falling-time-ns : should contain the SCL falling time in nanoseconds. + This value which is by default 300ns is used to compute the tLOW period. + + - i2c-sda-falling-time-ns : should contain the SDA falling time in nanoseconds. + This value which is by default 300ns is used to compute the tHIGH period. + +Example : + + i2c@f0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xf0000 0x1000>; + interrupts = <11>; + clock-frequency = <400000>; + }; + + i2c@1120000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0x1120000 0x1000>; + interrupt-parent = <&ictl>; + interrupts = <12 1>; + clock-frequency = <400000>; + i2c-sda-hold-time-ns = <300>; + i2c-sda-falling-time-ns = <300>; + i2c-scl-falling-time-ns = <300>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-digicolor.txt b/Documentation/devicetree/bindings/i2c/i2c-digicolor.txt new file mode 100644 index 000000000..457a098d4 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-digicolor.txt @@ -0,0 +1,25 @@ +Conexant Digicolor I2C controller + +Required properties: + - compatible: must be "cnxt,cx92755-i2c" + - reg: physical address and length of the device registers + - interrupts: a single interrupt specifier + - clocks: clock for the device + - #address-cells: should be <1> + - #size-cells: should be <0> + +Optional properties: +- clock-frequency: the desired I2C bus clock frequency in Hz; in + absence of this property the default value is used (100 kHz). + +Example: + + i2c: i2c@f0000120 { + compatible = "cnxt,cx92755-i2c"; + reg = <0xf0000120 0x10>; + interrupts = <28>; + clocks = <&main_clk>; + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt new file mode 100644 index 000000000..50b25c3da --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt @@ -0,0 +1,34 @@ +* Energymicro efm32 i2c controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "energymicro,efm32-i2c" + - interrupts : the interrupt number + - clocks : reference to the module clock + +Recommended properties : + + - clock-frequency : maximal I2C bus clock frequency in Hz. + - energymicro,location : Decides the location of the USART I/O pins. + Allowed range : [0 .. 6] + +Example: + i2c0: i2c@4000a000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "energymicro,efm32-i2c"; + reg = <0x4000a000 0x400>; + interrupts = <9>; + clocks = <&cmu clk_HFPERCLKI2C0>; + clock-frequency = <100000>; + status = "ok"; + energymicro,location = <3>; + + eeprom@50 { + compatible = "microchip,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + }; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt new file mode 100644 index 000000000..2dbc0b62d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt @@ -0,0 +1,53 @@ +* Samsung's High Speed I2C controller + +The Samsung's High Speed I2C controller is used to interface with I2C devices +at various speeds ranging from 100khz to 3.4Mhz. + +Required properties: + - compatible: value should be. + -> "samsung,exynos5-hsi2c", (DEPRECATED) + for i2c compatible with HSI2C available + on Exynos5250 and Exynos5420 SoCs. + -> "samsung,exynos5250-hsi2c", for i2c compatible with HSI2C available + on Exynos5250 and Exynos5420 SoCs. + -> "samsung,exynos5260-hsi2c", for i2c compatible with HSI2C available + on Exynos5260 SoCs. + -> "samsung,exynos7-hsi2c", for i2c compatible with HSI2C available + on Exynos7 SoCs. + + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - #address-cells: always 1 (for i2c addresses) + - #size-cells: always 0 + + - Pinctrl: + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + +Optional properties: + - clock-frequency: Desired operating frequency in Hz of the bus. + -> If not specified, the bus operates in fast-speed mode at + at 100khz. + -> If specified, the bus operates in high-speed mode only if the + clock-frequency is >= 1Mhz. + +Example: + +hsi2c@12ca0000 { + compatible = "samsung,exynos5250-hsi2c"; + reg = <0x12ca0000 0x100>; + interrupts = <56>; + clock-frequency = <100000>; + + pinctrl-0 = <&i2c4_bus>; + pinctrl-names = "default"; + + #address-cells = <1>; + #size-cells = <0>; + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-gpio.txt new file mode 100644 index 000000000..4f8ec947c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-gpio.txt @@ -0,0 +1,32 @@ +Device-Tree bindings for i2c gpio driver + +Required properties: + - compatible = "i2c-gpio"; + - gpios: sda and scl gpio + + +Optional properties: + - i2c-gpio,sda-open-drain: sda as open drain + - i2c-gpio,scl-open-drain: scl as open drain + - i2c-gpio,scl-output-only: scl as output only + - i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform) + - i2c-gpio,timeout-ms: timeout to get data + +Example nodes: + +i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 23 0 /* sda */ + &pioA 24 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + + rv3029c2@56 { + compatible = "rv3029c2"; + reg = <0x56>; + }; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt b/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt new file mode 100644 index 000000000..f98b37401 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt @@ -0,0 +1,24 @@ +I2C for Hisilicon hix5hd2 chipset platform + +Required properties: +- compatible: Must be "hisilicon,hix5hd2-i2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- #address-cells = <1>; +- #size-cells = <0>; +- clocks: phandles to input clocks. + +Optional properties: +- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000 +- Child nodes conforming to i2c bus binding + +Examples: +I2C0@f8b10000 { + compatible = "hisilicon,hix5hd2-i2c"; + reg = <0xf8b10000 0x1000>; + interrupts = <0 38 4>; + clocks = <&clock HIX5HD2_I2C0_RST>; + #address-cells = <1>; + #size-cells = <0>; +} diff --git a/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt new file mode 100644 index 000000000..b6461602d --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt @@ -0,0 +1,26 @@ +IMG Serial Control Bus (SCB) I2C Controller + +Required Properties: +- compatible: "img,scb-i2c" +- reg: Physical base address and length of controller registers +- interrupts: Interrupt number used by the controller +- clocks : Should contain a clock specifier for each entry in clock-names +- clock-names : Should contain the following entries: + "scb", for the SCB core clock. + "sys", for the system clock. +- clock-frequency: The I2C bus frequency in Hz +- #address-cells: Should be <1> +- #size-cells: Should be <0> + +Example: + +i2c@18100000 { + compatible = "img,scb-i2c"; + reg = <0x18100000 0x200>; + interrupts = <GIC_SHARED 2 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&i2c0_clk>, <&system_clk>; + clock-names = "scb", "sys"; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt new file mode 100644 index 000000000..ce4311d72 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt @@ -0,0 +1,40 @@ +* Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX + +Required properties: +- compatible : + - "fsl,imx1-i2c" for I2C compatible with the one integrated on i.MX1 SoC + - "fsl,imx21-i2c" for I2C compatible with the one integrated on i.MX21 SoC + - "fsl,vf610-i2c" for I2C compatible with the one integrated on Vybrid vf610 SoC +- reg : Should contain I2C/HS-I2C registers location and length +- interrupts : Should contain I2C/HS-I2C interrupt +- clocks : Should contain the I2C/HS-I2C clock specifier + +Optional properties: +- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. + The absence of the propoerty indicates the default frequency 100 kHz. +- dmas: A list of two dma specifiers, one for each entry in dma-names. +- dma-names: should contain "tx" and "rx". + +Examples: + +i2c@83fc4000 { /* I2C2 on i.MX51 */ + compatible = "fsl,imx51-i2c", "fsl,imx21-i2c"; + reg = <0x83fc4000 0x4000>; + interrupts = <63>; +}; + +i2c@70038000 { /* HS-I2C on i.MX51 */ + compatible = "fsl,imx51-i2c", "fsl,imx21-i2c"; + reg = <0x70038000 0x4000>; + interrupts = <64>; + clock-frequency = <400000>; +}; + +i2c0: i2c@40066000 { /* i2c0 on vf610 */ + compatible = "fsl,vf610-i2c"; + reg = <0x40066000 0x1000>; + interrupts =<0 71 0x04>; + dmas = <&edma0 0 50>, + <&edma0 0 51>; + dma-names = "rx","tx"; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt b/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt new file mode 100644 index 000000000..231e4cc40 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt @@ -0,0 +1,35 @@ +* Ingenic JZ4780 I2C Bus controller + +Required properties: +- compatible: should be "ingenic,jz4780-i2c" +- reg: Should contain the address & size of the I2C controller registers. +- interrupts: Should specify the interrupt provided by parent. +- clocks: Should contain a single clock specifier for the JZ4780 I2C clock. +- clock-frequency: desired I2C bus clock frequency in Hz. + +Recommended properties: +- pinctrl-names: should be "default"; +- pinctrl-0: phandle to pinctrl function + +Optional properties: +- interrupt-parent: Should be the phandle of the interrupt controller that + delivers interrupts to the I2C block. + +Example + +/ { + i2c4: i2c4@0x10054000 { + compatible = "ingenic,jz4780-i2c"; + reg = <0x10054000 0x1000>; + + interrupt-parent = <&intc>; + interrupts = <56>; + + clocks = <&cgu JZ4780_CLK_SMB4>; + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pins_i2c4_data>; + + }; +}; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-meson.txt b/Documentation/devicetree/bindings/i2c/i2c-meson.txt new file mode 100644 index 000000000..682f9a6f7 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-meson.txt @@ -0,0 +1,24 @@ +Amlogic Meson I2C controller + +Required properties: + - compatible: must be "amlogic,meson6-i2c" + - reg: physical address and length of the device registers + - interrupts: a single interrupt specifier + - clocks: clock for the device + - #address-cells: should be <1> + - #size-cells: should be <0> + +Optional properties: +- clock-frequency: the desired I2C bus clock frequency in Hz; in + absence of this property the default value is used (100 kHz). + +Examples: + + i2c@c8100500 { + compatible = "amlogic,meson6-i2c"; + reg = <0xc8100500 0x20>; + interrupts = <0 92 1>; + clocks = <&clk81>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mpc.txt b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt new file mode 100644 index 000000000..1eacd6b20 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt @@ -0,0 +1,64 @@ +* I2C + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a + compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121, + mpc5200 or mpc5200b. For the mpc5121, an additional node + "fsl,mpc5121-i2c-ctrl" is required as shown in the example below. + +Recommended properties : + + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. + - fsl,preserve-clocking : boolean; if defined, the clock settings + from the bootloader are preserved (not touched). + - clock-frequency : desired I2C bus clock frequency in Hz. + - fsl,timeout : I2C bus timeout in microseconds. + +Examples : + + /* MPC5121 based board */ + i2c@1740 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5121-i2c", "fsl-i2c"; + reg = <0x1740 0x20>; + interrupts = <11 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <100000>; + }; + + i2ccontrol@1760 { + compatible = "fsl,mpc5121-i2c-ctrl"; + reg = <0x1760 0x8>; + }; + + /* MPC5200B based board */ + i2c@3d00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; + reg = <0x3d00 0x40>; + interrupts = <2 15 0>; + interrupt-parent = <&mpc5200_pic>; + fsl,preserve-clocking; + }; + + /* MPC8544 base board */ + i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc8544-i2c", "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + clock-frequency = <400000>; + fsl,timeout = <10000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt new file mode 100644 index 000000000..66709a825 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt @@ -0,0 +1,81 @@ +GPIO-based I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses GPIOs to +route the I2C signals. + + +-----+ +-----+ + | dev | | dev | + +------------+ +-----+ +-----+ + | SoC | | | + | | /--------+--------+ + | +------+ | +------+ child bus A, on GPIO value set to 0 + | | I2C |-|--| Mux | + | +------+ | +--+---+ child bus B, on GPIO value set to 1 + | | | \----------+--------+--------+ + | +------+ | | | | | + | | GPIO |-|-----+ +-----+ +-----+ +-----+ + | +------+ | | dev | | dev | | dev | + +------------+ +-----+ +-----+ +-----+ + +Required properties: +- compatible: i2c-mux-gpio +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. +- mux-gpios: list of gpios used to control the muxer +* Standard I2C mux properties. See mux.txt in this directory. +* I2C child bus nodes. See mux.txt in this directory. + +Optional properties: +- idle-state: value to set the muxer to when idle. When no value is + given, it defaults to the last value used. + +For each i2c child node, an I2C child bus will be created. They will +be numbered based on their order in the device tree. + +Whenever an access is made to a device on a child bus, the value set +in the revelant node's reg property will be output using the list of +GPIOs, the first in the list holding the least-significant value. + +If an idle state is defined, using the idle-state (optional) property, +whenever an access is not being made to a device on a child bus, the +GPIOs will be set according to the idle value. + +If an idle state is not defined, the most recently used value will be +left programmed into hardware whenever no access is being made to a +device on a child bus. + +Example: + i2cmux { + compatible = "i2c-mux-gpio"; + #address-cells = <1>; + #size-cells = <0>; + mux-gpios = <&gpio1 22 0 &gpio1 23 0>; + i2c-parent = <&i2c1>; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + compatible = "solomon,ssd1307fb-i2c"; + reg = <0x3c>; + pwms = <&pwm 4 3000>; + reset-gpios = <&gpio2 7 1>; + reset-active-low; + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt new file mode 100644 index 000000000..cf53d5fba --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt @@ -0,0 +1,53 @@ +* NXP PCA954x I2C bus switch + +Required Properties: + + - compatible: Must contain one of the following. + "nxp,pca9540", "nxp,pca9542", "nxp,pca9543", "nxp,pca9544", + "nxp,pca9545", "nxp,pca9546", "nxp,pca9547", "nxp,pca9548" + + - reg: The I2C address of the device. + + The following required properties are defined externally: + + - Standard I2C mux properties. See i2c-mux.txt in this directory. + - I2C child bus nodes. See i2c-mux.txt in this directory. + +Optional Properties: + + - reset-gpios: Reference to the GPIO connected to the reset input. + - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all + children in idle state. This is necessary for example, if there are several + multiplexers on the bus and the devices behind them use same I2C addresses. + + +Example: + + i2c-switch@74 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + + eeprom@54 { + compatible = "at,24c08"; + reg = <0x54>; + }; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt new file mode 100644 index 000000000..ae8af1694 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt @@ -0,0 +1,93 @@ +Pinctrl-based I2C Bus Mux + +This binding describes an I2C bus multiplexer that uses pin multiplexing to +route the I2C signals, and represents the pin multiplexing configuration +using the pinctrl device tree bindings. + + +-----+ +-----+ + | dev | | dev | + +------------------------+ +-----+ +-----+ + | SoC | | | + | /----|------+--------+ + | +---+ +------+ | child bus A, on first set of pins + | |I2C|---|Pinmux| | + | +---+ +------+ | child bus B, on second set of pins + | \----|------+--------+--------+ + | | | | | + +------------------------+ +-----+ +-----+ +-----+ + | dev | | dev | | dev | + +-----+ +-----+ +-----+ + +Required properties: +- compatible: i2c-mux-pinctrl +- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side + port is connected to. + +Also required are: + +* Standard pinctrl properties that specify the pin mux state for each child + bus. See ../pinctrl/pinctrl-bindings.txt. + +* Standard I2C mux properties. See mux.txt in this directory. + +* I2C child bus nodes. See mux.txt in this directory. + +For each named state defined in the pinctrl-names property, an I2C child bus +will be created. I2C child bus numbers are assigned based on the index into +the pinctrl-names property. + +The only exception is that no bus will be created for a state named "idle". If +such a state is defined, it must be the last entry in pinctrl-names. For +example: + + pinctrl-names = "ddc", "pta", "idle" -> ddc = bus 0, pta = bus 1 + pinctrl-names = "ddc", "idle", "pta" -> Invalid ("idle" not last) + pinctrl-names = "idle", "ddc", "pta" -> Invalid ("idle" not last) + +Whenever an access is made to a device on a child bus, the relevant pinctrl +state will be programmed into hardware. + +If an idle state is defined, whenever an access is not being made to a device +on a child bus, the idle pinctrl state will be programmed into hardware. + +If an idle state is not defined, the most recently used pinctrl state will be +left programmed into hardware whenever no access is being made of a device on +a child bus. + +Example: + + i2cmux { + compatible = "i2c-mux-pinctrl"; + #address-cells = <1>; + #size-cells = <0>; + + i2c-parent = <&i2c1>; + + pinctrl-names = "ddc", "pta", "idle"; + pinctrl-0 = <&state_i2cmux_ddc>; + pinctrl-1 = <&state_i2cmux_pta>; + pinctrl-2 = <&state_i2cmux_idle>; + + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom { + compatible = "eeprom"; + reg = <0x50>; + }; + }; + + i2c@1 { + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom { + compatible = "eeprom"; + reg = <0x50>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux.txt new file mode 100644 index 000000000..af84cce5c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mux.txt @@ -0,0 +1,60 @@ +Common i2c bus multiplexer/switch properties. + +An i2c bus multiplexer/switch will have several child busses that are +numbered uniquely in a device dependent manner. The nodes for an i2c bus +multiplexer/switch will have one child node for each child +bus. + +Required properties: +- #address-cells = <1>; +- #size-cells = <0>; + +Required properties for child nodes: +- #address-cells = <1>; +- #size-cells = <0>; +- reg : The sub-bus number. + +Optional properties for child nodes: +- Other properties specific to the multiplexer/switch hardware. +- Child nodes conforming to i2c bus binding + + +Example : + + /* + An NXP pca9548 8 channel I2C multiplexer at address 0x70 + with two NXP pca8574 GPIO expanders attached, one each to + ports 3 and 4. + */ + + mux@70 { + compatible = "nxp,pca9548"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + + gpio1: gpio@38 { + compatible = "nxp,pca8574"; + reg = <0x38>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + + gpio2: gpio@38 { + compatible = "nxp,pca8574"; + reg = <0x38>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt new file mode 100644 index 000000000..5c3002692 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt @@ -0,0 +1,44 @@ + +* Marvell MV64XXX I2C controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : Should be either: + - "allwinner,sun4i-a10-i2c" + - "allwinner,sun6i-a31-i2c" + - "marvell,mv64xxx-i2c" + - "marvell,mv78230-i2c" + - "marvell,mv78230-a0-i2c" + * Note: Only use "marvell,mv78230-a0-i2c" for a + very rare, initial version of the SoC which + had broken offload support. Linux + auto-detects this and sets it appropriately. + - interrupts : The interrupt number + +Optional properties : + + - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the +default frequency is 100kHz + + - resets : phandle to the parent reset controller. Mandatory + whenever you're using the "allwinner,sun6i-a31-i2c" + compatible. + +Examples: + + i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + interrupts = <29>; + clock-frequency = <100000>; + }; + +For the Armada XP: + + i2c@11000 { + compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c"; + reg = <0x11000 0x100>; + interrupts = <29>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt new file mode 100644 index 000000000..4e1c8ac01 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt @@ -0,0 +1,25 @@ +* Freescale MXS Inter IC (I2C) Controller + +Required properties: +- compatible: Should be "fsl,<chip>-i2c" +- reg: Should contain registers location and length +- interrupts: Should contain ERROR interrupt number +- clock-frequency: Desired I2C bus clock frequency in Hz. + Only 100000Hz and 400000Hz modes are supported. +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and I2C DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: Must be "rx-tx". + +Examples: + +i2c0: i2c@80058000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-i2c"; + reg = <0x80058000 2000>; + interrupts = <111>; + clock-frequency = <100000>; + dmas = <&dma_apbx 6>; + dma-names = "rx-tx"; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt new file mode 100644 index 000000000..72065b0ff --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt @@ -0,0 +1,23 @@ +I2C for Nomadik based systems + +Required (non-standard) properties: + - Nil + +Recommended (non-standard) properties: + - clock-frequency : Maximum bus clock frequency for the device + +Optional (non-standard) properties: + - Nil + +Example : + +i2c@80004000 { + compatible = "stericsson,db8500-i2c", "st,nomadik-i2c"; + reg = <0x80004000 0x1000>; + interrupts = <0 21 0x4>; + #address-cells = <1>; + #size-cells = <0>; + v-i2c-supply = <&db8500_vape_reg>; + + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt new file mode 100644 index 000000000..17bef9a34 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt @@ -0,0 +1,69 @@ +Device tree configuration for i2c-ocores + +Required properties: +- compatible : "opencores,i2c-ocores" or "aeroflexgaisler,i2cmst" +- reg : bus address start and address range size of device +- interrupts : interrupt number +- clocks : handle to the controller clock; see the note below. + Mutually exclusive with opencores,ip-clock-frequency +- opencores,ip-clock-frequency: frequency of the controller clock in Hz; + see the note below. Mutually exclusive with clocks +- #address-cells : should be <1> +- #size-cells : should be <0> + +Optional properties: +- clock-frequency : frequency of bus clock in Hz; see the note below. + Defaults to 100 KHz when the property is not specified +- reg-shift : device register offsets are shifted by this value +- reg-io-width : io register width in bytes (1, 2 or 4) +- regstep : deprecated, use reg-shift above + +Note +clock-frequency property is meant to control the bus frequency for i2c bus +drivers, but it was incorrectly used to specify i2c controller input clock +frequency. So the following rules are set to fix this situation: +- if clock-frequency is present and neither opencores,ip-clock-frequency nor + clocks are, then clock-frequency specifies i2c controller clock frequency. + This is to keep backwards compatibility with setups using old DTB. i2c bus + frequency is fixed at 100 KHz. +- if clocks is present it specifies i2c controller clock. clock-frequency + property specifies i2c bus frequency. +- if opencores,ip-clock-frequency is present it specifies i2c controller + clock frequency. clock-frequency property specifies i2c bus frequency. + +Examples: + + i2c0: ocores@a0000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "opencores,i2c-ocores"; + reg = <0xa0000000 0x8>; + interrupts = <10>; + opencores,ip-clock-frequency = <20000000>; + + reg-shift = <0>; /* 8 bit registers */ + reg-io-width = <1>; /* 8 bit read/write */ + + dummy@60 { + compatible = "dummy"; + reg = <0x60>; + }; + }; +or + i2c0: ocores@a0000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "opencores,i2c-ocores"; + reg = <0xa0000000 0x8>; + interrupts = <10>; + clocks = <&osc>; + clock-frequency = <400000>; /* i2c bus frequency 400 KHz */ + + reg-shift = <0>; /* 8 bit registers */ + reg-io-width = <1>; /* 8 bit read/write */ + + dummy@60 { + compatible = "dummy"; + reg = <0x60>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-octeon.txt b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt new file mode 100644 index 000000000..dced82ebe --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt @@ -0,0 +1,34 @@ +* Two Wire Serial Interface (TWSI) / I2C + +- compatible: "cavium,octeon-3860-twsi" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the TWSI/I2C bus controller register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. I2C addresses have no size component. + +- interrupts: A single interrupt specifier. + +- clock-frequency: The I2C bus clock rate in Hz. + +Example: + twsi0: i2c@1180000001000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "cavium,octeon-3860-twsi"; + reg = <0x11800 0x00001000 0x0 0x200>; + interrupts = <0 45>; + clock-frequency = <100000>; + + rtc@68 { + compatible = "dallas,ds1337"; + reg = <0x68>; + }; + tmp@4c { + compatible = "ti,tmp421"; + reg = <0x4c>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-omap.txt b/Documentation/devicetree/bindings/i2c/i2c-omap.txt new file mode 100644 index 000000000..7e49839d4 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-omap.txt @@ -0,0 +1,31 @@ +I2C for OMAP platforms + +Required properties : +- compatible : Must be "ti,omap2420-i2c", "ti,omap2430-i2c", "ti,omap3-i2c" + or "ti,omap4-i2c" +- ti,hwmods : Must be "i2c<n>", n being the instance number (1-based) +- #address-cells = <1>; +- #size-cells = <0>; + +Recommended properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. Otherwise + the default 100 kHz frequency will be used. + +Optional properties: +- Child nodes conforming to i2c bus binding + +Note: Current implementation will fetch base address, irq and dma +from omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples : + +i2c1: i2c@0 { + compatible = "ti,omap3-i2c"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c1"; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-opal.txt b/Documentation/devicetree/bindings/i2c/i2c-opal.txt new file mode 100644 index 000000000..12bc61465 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-opal.txt @@ -0,0 +1,37 @@ +Device-tree bindings for I2C OPAL driver +---------------------------------------- + +Most of the device node and properties layout is specific to the firmware and +used by the firmware itself for configuring the port. From the linux +perspective, the properties of use are "ibm,port-name" and "ibm,opal-id". + +Required properties: + +- reg: Port-id within a given master +- compatible: must be "ibm,opal-i2c" +- ibm,opal-id: Refers to a specific bus and used to identify it when calling + the relevant OPAL functions. +- bus-frequency: Operating frequency of the i2c bus (in HZ). Informational for + linux, used by the FW though. + +Optional properties: +- ibm,port-name: Firmware provides this name that uniquely identifies the i2c + port. + +The node contains a number of other properties that are used by the FW itself +and depend on the specific hardware implementation. The example below depicts +a P8 on-chip bus. + +Example: + +i2c-bus@0 { + reg = <0x0>; + bus-frequency = <0x61a80>; + compatible = "ibm,power8-i2c-port", "ibm,opal-i2c"; + ibm,opal-id = <0x1>; + ibm,port-name = "p8_00000000_e1p0"; + #address-cells = <0x1>; + phandle = <0x10000006>; + #size-cells = <0x0>; + linux,phandle = <0x10000006>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pnx.txt b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt new file mode 100644 index 000000000..fe98ada33 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt @@ -0,0 +1,36 @@ +* NXP PNX I2C Controller + +Required properties: + + - reg: Offset and length of the register set for the device + - compatible: should be "nxp,pnx-i2c" + - interrupts: configure one interrupt line + - #address-cells: always 1 (for i2c addresses) + - #size-cells: always 0 + - interrupt-parent: the phandle for the interrupt controller that + services interrupts for this device. + +Optional properties: + + - clock-frequency: desired I2C bus clock frequency in Hz, Default: 100000 Hz + +Examples: + + i2c1: i2c@400a0000 { + compatible = "nxp,pnx-i2c"; + reg = <0x400a0000 0x100>; + interrupt-parent = <&mic>; + interrupts = <51 0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@400a8000 { + compatible = "nxp,pnx-i2c"; + reg = <0x400a8000 0x100>; + interrupt-parent = <&mic>; + interrupts = <50 0>; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <100000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt new file mode 100644 index 000000000..569b16248 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt @@ -0,0 +1,93 @@ +CE4100 I2C +---------- + +CE4100 has one PCI device which is described as the I2C-Controller. This +PCI device has three PCI-bars, each bar contains a complete I2C +controller. So we have a total of three independent I2C-Controllers +which share only an interrupt line. +The driver is probed via the PCI-ID and is gathering the information of +attached devices from the devices tree. +Grant Likely recommended to use the ranges property to map the PCI-Bar +number to its physical address and to use this to find the child nodes +of the specific I2C controller. This were his exact words: + + Here's where the magic happens. Each entry in + ranges describes how the parent pci address space + (middle group of 3) is translated to the local + address space (first group of 2) and the size of + each range (last cell). In this particular case, + the first cell of the local address is chosen to be + 1:1 mapped to the BARs, and the second is the + offset from be base of the BAR (which would be + non-zero if you had 2 or more devices mapped off + the same BAR) + + ranges allows the address mapping to be described + in a way that the OS can interpret without + requiring custom device driver code. + +This is an example which is used on FalconFalls: +------------------------------------------------ + i2c-controller@b,2 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "pci8086,2e68.2", + "pci8086,2e68", + "pciclass,ff0000", + "pciclass,ff00"; + + reg = <0x15a00 0x0 0x0 0x0 0x0>; + interrupts = <16 1>; + + /* as described by Grant, the first number in the group of + * three is the bar number followed by the 64bit bar address + * followed by size of the mapping. The bar address + * requires also a valid translation in parents ranges + * property. + */ + ranges = <0 0 0x02000000 0 0xdffe0500 0x100 + 1 0 0x02000000 0 0xdffe0600 0x100 + 2 0 0x02000000 0 0xdffe0700 0x100>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + + /* The first number in the reg property is the + * number of the bar + */ + reg = <0 0 0x100>; + + /* This I2C controller has no devices */ + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + reg = <1 0 0x100>; + + /* This I2C controller has one gpio controller */ + gpio@26 { + #gpio-cells = <2>; + compatible = "ti,pcf8575"; + reg = <0x26>; + gpio-controller; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "intel,ce4100-i2c-controller"; + reg = <2 0 0x100>; + + gpio@26 { + #gpio-cells = <2>; + compatible = "ti,pcf8575"; + reg = <0x26>; + gpio-controller; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt new file mode 100644 index 000000000..12b78ac50 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt @@ -0,0 +1,33 @@ +* Marvell MMP I2C controller + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "mrvl,mmp-twsi" where mmp is the name of a + compatible processor, e.g. pxa168, pxa910, mmp2, mmp3. + For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required + as shown in the example below. + +Recommended properties : + + - interrupts : the interrupt number + - interrupt-parent : the phandle for the interrupt controller that + services interrupts for this device. If the parent is the default + interrupt controller in device tree, it could be ignored. + - mrvl,i2c-polling : Disable interrupt of i2c controller. Polling + status register of i2c controller instead. + - mrvl,i2c-fast-mode : Enable fast mode of i2c controller. + +Examples: + twsi1: i2c@d4011000 { + compatible = "mrvl,mmp-twsi"; + reg = <0xd4011000 0x1000>; + interrupts = <7>; + mrvl,i2c-fast-mode; + }; + + twsi2: i2c@d4025000 { + compatible = "mrvl,mmp-twsi"; + reg = <0xd4025000 0x1000>; + interrupts = <58>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt new file mode 100644 index 000000000..16b3e07aa --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -0,0 +1,32 @@ +I2C for R-Car platforms + +Required properties: +- compatible: Must be one of + "renesas,i2c-rcar" + "renesas,i2c-r8a7778" + "renesas,i2c-r8a7779" + "renesas,i2c-r8a7790" + "renesas,i2c-r8a7791" + "renesas,i2c-r8a7792" + "renesas,i2c-r8a7793" + "renesas,i2c-r8a7794" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt specifier. + +Optional properties: +- clock-frequency: desired I2C bus clock frequency in Hz. The absence of this + propoerty indicates the default frequency 100 kHz. +- clocks: clock specifier. + +Examples : + +i2c0: i2c@e6508000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7791"; + reg = <0 0xe6508000 0 0x40>; + interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_I2C0>; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-riic.txt b/Documentation/devicetree/bindings/i2c/i2c-riic.txt new file mode 100644 index 000000000..0bcc4716c --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-riic.txt @@ -0,0 +1,29 @@ +Device tree configuration for Renesas RIIC driver + +Required properties: +- compatible : "renesas,riic-<soctype>". "renesas,riic-rz" as fallback +- reg : address start and address range size of device +- interrupts : 8 interrupts (TEI, RI, TI, SPI, STI, NAKI, ALI, TMOI) +- clock-frequency : frequency of bus clock in Hz +- #address-cells : should be <1> +- #size-cells : should be <0> + +Pinctrl properties might be needed, too. See there. + +Example: + + i2c0: i2c@fcfee000 { + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfee000 0x44>; + interrupts = <0 157 IRQ_TYPE_LEVEL_HIGH>, + <0 158 IRQ_TYPE_EDGE_RISING>, + <0 159 IRQ_TYPE_EDGE_RISING>, + <0 160 IRQ_TYPE_LEVEL_HIGH>, + <0 161 IRQ_TYPE_LEVEL_HIGH>, + <0 162 IRQ_TYPE_LEVEL_HIGH>, + <0 163 IRQ_TYPE_LEVEL_HIGH>, + <0 164 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <100000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt new file mode 100644 index 000000000..f0d71bc52 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt @@ -0,0 +1,56 @@ +* Rockchip RK3xxx I2C controller + +This driver interfaces with the native I2C controller present in Rockchip +RK3xxx SoCs. + +Required properties : + + - reg : Offset and length of the register set for the device + - compatible : should be "rockchip,rk3066-i2c", "rockchip,rk3188-i2c" or + "rockchip,rk3288-i2c". + - interrupts : interrupt number + - clocks : parent clock + +Required on RK3066, RK3188 : + + - rockchip,grf : the phandle of the syscon node for the general register + file (GRF) + - on those SoCs an alias with the correct I2C bus ID (bit offset in the GRF) + is also required. + +Optional properties : + + - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used. + - i2c-scl-rising-time-ns : Number of nanoseconds the SCL signal takes to rise + (t(r) in I2C specification). If not specified this is assumed to be + the maximum the specification allows(1000 ns for Standard-mode, + 300 ns for Fast-mode) which might cause slightly slower communication. + - i2c-scl-falling-time-ns : Number of nanoseconds the SCL signal takes to fall + (t(f) in the I2C specification). If not specified this is assumed to + be the maximum the specification allows (300 ns) which might cause + slightly slower communication. + - i2c-sda-falling-time-ns : Number of nanoseconds the SDA signal takes to fall + (t(f) in the I2C specification). If not specified we'll use the SCL + value since they are the same in nearly all cases. + +Example: + +aliases { + i2c0 = &i2c0; +} + +i2c0: i2c@2002d000 { + compatible = "rockchip,rk3188-i2c"; + reg = <0x2002d000 0x1000>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + rockchip,grf = <&grf>; + + clock-names = "i2c"; + clocks = <&cru PCLK_I2C0>; + + i2c-scl-rising-time-ns = <800>; + i2c-scl-falling-time-ns = <100>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt new file mode 100644 index 000000000..89b3250f0 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt @@ -0,0 +1,60 @@ +* Samsung's I2C controller + +The Samsung's I2C controller is used to interface with I2C devices. + +Required properties: + - compatible: value should be either of the following. + (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c. + (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c. + (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used + inside HDMIPHY block found on several samsung SoCs + (d) "samsung, exynos5440-i2c", for s3c2440-like i2c used + on EXYNOS5440 which does not need GPIO configuration. + (e) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as + a host to SATA PHY controller on an internal bus. + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. + +Required for all cases except "samsung,s3c2440-hdmiphy-i2c": + - Samsung GPIO variant (deprecated): + - gpios: The order of the gpios should be the following: <SDA, SCL>. + The gpio specifier depends on the gpio controller. Required in all + cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output + lines are permanently wired to the respective clienta + - Pinctrl variant (preferred, if available): + - pinctrl-0: Pin control group to be used for this controller. + - pinctrl-names: Should contain only one value - "default". + +Optional properties: + - samsung,i2c-slave-addr: Slave address in multi-master environment. If not + specified, default value is 0. + - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not + specified, the default value in Hz is 100000. + - samsung,sysreg-phandle - handle to syscon used to control the system registers + +Example: + + i2c@13870000 { + compatible = "samsung,s3c2440-i2c"; + reg = <0x13870000 0x100>; + interrupts = <345>; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <100000>; + /* Samsung GPIO variant begins here */ + gpios = <&gpd1 2 0 /* SDA */ + &gpd1 3 0 /* SCL */>; + /* Samsung GPIO variant ends here */ + /* Pinctrl variant begins here */ + pinctrl-0 = <&i2c3_bus>; + pinctrl-names = "default"; + /* Pinctrl variant ends here */ + #address-cells = <1>; + #size-cells = <0>; + + wm8994@1a { + compatible = "wlf,wm8994"; + reg = <0x1a>; + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt new file mode 100644 index 000000000..2bfc6e7ed --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -0,0 +1,40 @@ +Device tree configuration for Renesas IIC (sh_mobile) driver + +Required properties: +- compatible : "renesas,iic-<soctype>". "renesas,rmobile-iic" as fallback + Examples with soctypes are: + - "renesas,iic-r8a73a4" (R-Mobile APE6) + - "renesas,iic-r8a7740" (R-Mobile A1) + - "renesas,iic-r8a7790" (R-Car H2) + - "renesas,iic-r8a7791" (R-Car M2-W) + - "renesas,iic-r8a7792" (R-Car V2H) + - "renesas,iic-r8a7793" (R-Car M2-N) + - "renesas,iic-r8a7794" (R-Car E2) + - "renesas,iic-sh73a0" (SH-Mobile AG5) +- reg : address start and address range size of device +- interrupts : interrupt of device +- clocks : clock for device +- #address-cells : should be <1> +- #size-cells : should be <0> + +Optional properties: +- clock-frequency : frequency of bus clock in Hz. Default 100kHz if unset. +- dmas : Must contain a list of two references to DMA + specifiers, one for transmission, and one for + reception. +- dma-names : Must contain a list of two DMA names, "tx" and "rx". + + +Pinctrl properties might be needed, too. See there. + +Example: + + iic0: i2c@e6500000 { + compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic"; + reg = <0 0xe6500000 0 0x425>; + interrupts = <0 174 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7790_CLK_IIC0>; + clock-frequency = <400000>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sirf.txt b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt new file mode 100644 index 000000000..7baf9e133 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt @@ -0,0 +1,19 @@ +I2C for SiRFprimaII platforms + +Required properties : +- compatible : Must be "sirf,prima2-i2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. + +Optional properties: +- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz. + The absence of the propoerty indicates the default frequency 100 kHz. + +Examples : + +i2c0: i2c@b00e0000 { + compatible = "sirf,prima2-i2c"; + reg = <0xb00e0000 0x10000>; + interrupts = <24>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-st-ddci2c.txt b/Documentation/devicetree/bindings/i2c/i2c-st-ddci2c.txt new file mode 100644 index 000000000..bd81a4826 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-st-ddci2c.txt @@ -0,0 +1,15 @@ +ST Microelectronics DDC I2C + +Required properties : +- compatible : Must be "st,ddci2c" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: interrupt number to the cpu. +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Child nodes conforming to i2c bus binding + +Examples : + diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt new file mode 100644 index 000000000..4c26fda38 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt @@ -0,0 +1,41 @@ +ST SSC binding, for I2C mode operation + +Required properties : +- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c" +- reg : Offset and length of the register set for the device +- interrupts : the interrupt specifier +- clock-names: Must contain "ssc". +- clocks: Must contain an entry for each name in clock-names. See the common + clock bindings. +- A pinctrl state named "default" must be defined to set pins in mode of + operation for I2C transfer. + +Optional properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified, + the default 100 kHz frequency will be used. As only Normal and Fast modes + are supported, possible values are 100000 and 400000. +- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is + allowed through the deglitch circuit. In units of us. +- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is + allowed through the deglitch circuit. In units of us. +- A pinctrl state named "idle" could be defined to set pins in idle state + when I2C instance is not performing a transfer. +- A pinctrl state named "sleep" could be defined to set pins in sleep state + when driver enters in suspend. + + + +Example : + +i2c0: i2c@fed40000 { + compatible = "st,comms-ssc4-i2c"; + reg = <0xfed40000 0x110>; + interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_s_a0_ls CLK_ICN_REG>; + clock-names = "ssc"; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c0_default>; + st,i2c-min-scl-pulse-width-us = <0>; + st,i2c-min-sda-pulse-width-us = <5>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt new file mode 100644 index 000000000..6b765485a --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt @@ -0,0 +1,41 @@ + +* Allwinner P2WI (Push/Pull 2 Wire Interface) controller + +Required properties : + + - reg : Offset and length of the register set for the device. + - compatible : Should one of the following: + - "allwinner,sun6i-a31-p2wi" + - interrupts : The interrupt line connected to the P2WI peripheral. + - clocks : The gate clk connected to the P2WI peripheral. + - resets : The reset line connected to the P2WI peripheral. + +Optional properties : + + - clock-frequency : Desired P2WI bus clock frequency in Hz. If not set the +default frequency is 100kHz + +A P2WI may contain one child node encoding a P2WI slave device. + +Slave device properties: + Required properties: + - reg : the I2C slave address used during the initialization + process to switch from I2C to P2WI mode + +Example: + + p2wi@01f03400 { + compatible = "allwinner,sun6i-a31-p2wi"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <6000000>; + resets = <&apb0_rst 3>; + + axp221: pmic@68 { + compatible = "x-powers,axp221"; + reg = <0x68>; + + /* ... */ + }; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-versatile.txt b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt new file mode 100644 index 000000000..361d31c51 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt @@ -0,0 +1,10 @@ +i2c Controller on ARM Versatile platform: + +Required properties: +- compatible : Must be "arm,versatile-i2c"; +- reg +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Child nodes conforming to i2c bus binding diff --git a/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt b/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt new file mode 100644 index 000000000..94a425eaa --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt @@ -0,0 +1,24 @@ +* Wondermedia I2C Controller + +Required properties : + + - compatible : should be "wm,wm8505-i2c" + - reg : Offset and length of the register set for the device + - interrupts : <IRQ> where IRQ is the interrupt number + - clocks : phandle to the I2C clock source + +Optional properties : + + - clock-frequency : desired I2C bus clock frequency in Hz. + Valid values are 100000 and 400000. + Default to 100000 if not specified, or invalid value. + +Example : + + i2c_0: i2c@d8280000 { + compatible = "wm,wm8505-i2c"; + reg = <0xd8280000 0x1000>; + interrupts = <19>; + clocks = <&clki2c0>; + clock-frequency = <400000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-xiic.txt b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt new file mode 100644 index 000000000..ceabbe91a --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt @@ -0,0 +1,22 @@ +Xilinx IIC controller: + +Required properties: +- compatible : Must be "xlnx,xps-iic-2.00.a" +- reg : IIC register location and length +- interrupts : IIC controller unterrupt +- #address-cells = <1> +- #size-cells = <0> + +Optional properties: +- Child nodes conforming to i2c bus binding + +Example: + + axi_iic_0: i2c@40800000 { + compatible = "xlnx,xps-iic-2.00.a"; + interrupts = < 1 2 >; + reg = < 0x40800000 0x10000 >; + + #size-cells = <0>; + #address-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt b/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt new file mode 100644 index 000000000..f818ef507 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt @@ -0,0 +1,22 @@ +Device tree configuration for the I2C controller on the XLP9xx/5xx SoC + +Required properties: +- compatible : should be "netlogic,xlp980-i2c" +- reg : bus address start and address range size of device +- interrupts : interrupt number + +Optional properties: +- clock-frequency : frequency of bus clock in Hz + Defaults to 100 KHz when the property is not specified + +Example: + +i2c0: i2c@113100 { + compatible = "netlogic,xlp980-i2c"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x113100 0x100>; + clock-frequency = <400000>; + interrupts = <30>; + interrupt-parent = <&pic>; +}; diff --git a/Documentation/devicetree/bindings/i2c/ina209.txt b/Documentation/devicetree/bindings/i2c/ina209.txt new file mode 100644 index 000000000..9dd2bee80 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ina209.txt @@ -0,0 +1,18 @@ +ina209 properties + +Required properties: +- compatible: Must be "ti,ina209" +- reg: I2C address + +Optional properties: + +- shunt-resistor + Shunt resistor value in micro-Ohm + +Example: + +temp-sensor@4c { + compatible = "ti,ina209"; + reg = <0x4c>; + shunt-resistor = <5000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/ina2xx.txt b/Documentation/devicetree/bindings/i2c/ina2xx.txt new file mode 100644 index 000000000..a2ad85d7e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ina2xx.txt @@ -0,0 +1,22 @@ +ina2xx properties + +Required properties: +- compatible: Must be one of the following: + - "ti,ina219" for ina219 + - "ti,ina220" for ina220 + - "ti,ina226" for ina226 + - "ti,ina230" for ina230 +- reg: I2C address + +Optional properties: + +- shunt-resistor + Shunt resistor value in micro-Ohm + +Example: + +ina220@44 { + compatible = "ti,ina220"; + reg = <0x44>; + shunt-resistor = <1000>; +}; diff --git a/Documentation/devicetree/bindings/i2c/max6697.txt b/Documentation/devicetree/bindings/i2c/max6697.txt new file mode 100644 index 000000000..5f793998e --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/max6697.txt @@ -0,0 +1,64 @@ +max6697 properties + +Required properties: +- compatible: + Should be one of + maxim,max6581 + maxim,max6602 + maxim,max6622 + maxim,max6636 + maxim,max6689 + maxim,max6693 + maxim,max6694 + maxim,max6697 + maxim,max6698 + maxim,max6699 +- reg: I2C address + +Optional properties: + +- smbus-timeout-disable + Set to disable SMBus timeout. If not specified, SMBus timeout will be + enabled. +- extended-range-enable + Only valid for MAX6581. Set to enable extended temperature range. + Extended temperature will be disabled if not specified. +- beta-compensation-enable + Only valid for MAX6693 and MX6694. Set to enable beta compensation on + remote temperature channel 1. + Beta compensation will be disabled if not specified. +- alert-mask + Alert bit mask. Alert disabled for bits set. + Select bit 0 for local temperature, bit 1..7 for remote temperatures. + If not specified, alert will be enabled for all channels. +- over-temperature-mask + Over-temperature bit mask. Over-temperature reporting disabled for + bits set. + Select bit 0 for local temperature, bit 1..7 for remote temperatures. + If not specified, over-temperature reporting will be enabled for all + channels. +- resistance-cancellation + Boolean for all chips other than MAX6581. Set to enable resistance + cancellation on remote temperature channel 1. + For MAX6581, resistance cancellation enabled for all channels if + specified as boolean, otherwise as per bit mask specified. + Only supported for remote temperatures (bit 1..7). + If not specified, resistance cancellation will be disabled for all + channels. +- transistor-ideality + For MAX6581 only. Two values; first is bit mask, second is ideality + select value as per MAX6581 data sheet. Select bit 1..7 for remote + channels. + Transistor ideality will be initialized to default (1.008) if not + specified. + +Example: + +temp-sensor@1a { + compatible = "maxim,max6697"; + reg = <0x1a>; + smbus-timeout-disable; + resistance-cancellation; + alert-mask = <0x72>; + over-temperature-mask = <0x7f>; +}; diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt new file mode 100644 index 000000000..656716b72 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt @@ -0,0 +1,75 @@ +NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver. + +Required properties: +- compatible : For Tegra20, must be one of "nvidia,tegra20-i2c-dvc" or + "nvidia,tegra20-i2c". For Tegra30, must be "nvidia,tegra30-i2c". + For Tegra114, must be "nvidia,tegra114-i2c". Otherwise, must be + "nvidia,<chip>-i2c", plus at least one of the above, where <chip> is + tegra124, tegra132, or tegra210. + Details of compatible are as follows: + nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C + controller. This only support master mode of I2C communication. Register + interface/offset and interrupts handling are different than generic I2C + controller. Driver of DVC I2C controller is only compatible with + "nvidia,tegra20-i2c-dvc". + nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support + master and slave mode of I2C communication. The i2c-tegra driver only + support master mode of I2C communication. Driver of I2C controller is + only compatible with "nvidia,tegra20-i2c". + nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is + very much similar to Tegra20 I2C controller with additional feature: + Continue Transfer Support. This feature helps to implement M_NO_START + as per I2C core API transfer flags. Driver of I2C controller is + compatible with "nvidia,tegra30-i2c" to enable the continue transfer + support. This is also compatible with "nvidia,tegra20-i2c" without + continue transfer support. + nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is + very much similar to Tegra30 I2C controller with some hardware + modification: + - Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and + fast-clk. Tegra114 has only one clock source called as div-clk and + hence clock mechanism is changed in I2C controller. + - Tegra30/Tegra20 I2C controller has enabled per packet transfer by + default and there is no way to disable it. Tegra114 has this + interrupt disable by default and SW need to enable explicitly. + Due to above changes, Tegra114 I2C driver makes incompatible with + previous hardware driver. Hence, tegra114 I2C controller is compatible + with "nvidia,tegra114-i2c". +- reg: Should contain I2C controller registers physical address and length. +- interrupts: Should contain I2C controller interrupts. +- address-cells: Address cells for I2C device address. +- size-cells: Size of the I2C device address. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + Tegra20/Tegra30: + - div-clk + - fast-clk + Tegra114: + - div-clk +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - i2c +- dmas: Must contain an entry for each entry in clock-names. + See ../dma/dma.txt for details. +- dma-names: Must include the following entries: + - rx + - tx + +Example: + + i2c@7000c000 { + compatible = "nvidia,tegra20-i2c"; + reg = <0x7000c000 0x100>; + interrupts = <0 38 0x04>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&tegra_car 12>, <&tegra_car 124>; + clock-names = "div-clk", "fast-clk"; + resets = <&tegra_car 12>; + reset-names = "i2c"; + dmas = <&apbdma 16>, <&apbdma 16>; + dma-names = "rx", "tx"; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt new file mode 100644 index 000000000..dc71754a5 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt @@ -0,0 +1,40 @@ +Qualcomm Universal Peripheral (QUP) I2C controller + +Required properties: + - compatible: Should be: + * "qcom,i2c-qup-v1.1.1" for 8660, 8960 and 8064. + * "qcom,i2c-qup-v2.1.1" for 8974 v1. + * "qcom,i2c-qup-v2.2.1" for 8974 v2 and later. + - reg: Should contain QUP register address and length. + - interrupts: Should contain I2C interrupt. + + - clocks: A list of phandles + clock-specifiers, one for each entry in + clock-names. + - clock-names: Should contain: + * "core" for the core clock + * "iface" for the AHB clock + + - #address-cells: Should be <1> Address cells for i2c device address + - #size-cells: Should be <0> as i2c addresses have no size component + +Optional properties: + - clock-frequency: Should specify the desired i2c bus clock frequency in Hz, + defaults to 100kHz if omitted. + +Child nodes should conform to i2c bus binding. + +Example: + + i2c@f9924000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0xf9924000 0x1000>; + interrupts = <0 96 0>; + + clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + + clock-frequency = <355000>; + + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/i2c/ti,bq32k.txt b/Documentation/devicetree/bindings/i2c/ti,bq32k.txt new file mode 100644 index 000000000..e204906b9 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ti,bq32k.txt @@ -0,0 +1,18 @@ +* TI BQ32000 I2C Serial Real-Time Clock + +Required properties: +- compatible: Should contain "ti,bq32000". +- reg: I2C address for chip + +Optional properties: +- trickle-resistor-ohms : Selected resistor for trickle charger + Values usable are 1120 and 20180 + Should be given if trickle charger should be enabled +- trickle-diode-disable : Do not use internal trickle charger diode + Should be given if internal trickle charger diode should be disabled +Example: + bq32000: rtc@68 { + compatible = "ti,bq32000"; + trickle-resistor-ohms = <1120>; + reg = <0x68>; + }; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt new file mode 100644 index 000000000..ad0c4ac91 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -0,0 +1,103 @@ +This is a list of trivial i2c devices that have simple device tree +bindings, consisting only of a compatible field, an address and +possibly an interrupt line. + +If a device needs more specific bindings, such as properties to +describe some aspect of it, there needs to be a specific binding +document for it just like any other devices. + + +Compatible Vendor / Chip +========== ============= +abracon,abb5zes3 AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface +ad,ad7414 SMBus/I2C Digital Temperature Sensor in 6-Pin SOT with SMBus Alert and Over Temperature Pin +ad,adm9240 ADM9240: Complete System Hardware Monitor for uProcessor-Based Systems +adi,adt7461 +/-1C TDM Extended Temp Range I.C +adt7461 +/-1C TDM Extended Temp Range I.C +adi,adt7473 +/-1C TDM Extended Temp Range I.C +adi,adt7475 +/-1C TDM Extended Temp Range I.C +adi,adt7476 +/-1C TDM Extended Temp Range I.C +adi,adt7490 +/-1C TDM Extended Temp Range I.C +adi,adxl345 Three-Axis Digital Accelerometer +adi,adxl346 Three-Axis Digital Accelerometer +adi,adxl34x Three-Axis Digital Accelerometer +at,24c08 i2c serial eeprom (24cxx) +atmel,24c00 i2c serial eeprom (24cxx) +atmel,24c01 i2c serial eeprom (24cxx) +atmel,24c02 i2c serial eeprom (24cxx) +atmel,24c04 i2c serial eeprom (24cxx) +atmel,24c16 i2c serial eeprom (24cxx) +atmel,24c32 i2c serial eeprom (24cxx) +atmel,24c64 i2c serial eeprom (24cxx) +atmel,24c128 i2c serial eeprom (24cxx) +atmel,24c256 i2c serial eeprom (24cxx) +atmel,24c512 i2c serial eeprom (24cxx) +atmel,24c1024 i2c serial eeprom (24cxx) +atmel,at97sc3204t i2c trusted platform module (TPM) +capella,cm32181 CM32181: Ambient Light Sensor +capella,cm3232 CM3232: Ambient Light Sensor +catalyst,24c32 i2c serial eeprom +cirrus,cs42l51 Cirrus Logic CS42L51 audio codec +dallas,ds1307 64 x 8, Serial, I2C Real-Time Clock +dallas,ds1338 I2C RTC with 56-Byte NV RAM +dallas,ds1340 I2C RTC with Trickle Charger +dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output +dallas,ds1631 High-Precision Digital Thermometer +dallas,ds1682 Total-Elapsed-Time Recorder with Alarm +dallas,ds1775 Tiny Digital Thermometer and Thermostat +dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM +dallas,ds4510 CPU Supervisor with Nonvolatile Memory and Programmable I/O +dallas,ds75 Digital Thermometer and Thermostat +dlg,da9053 DA9053: flexible system level PMIC with multicore support +dlg,da9063 DA9063: system PMIC for quad-core application processors +epson,rx8025 High-Stability. I2C-Bus INTERFACE REAL TIME CLOCK MODULE +epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE +fsl,mag3110 MAG3110: Xtrinsic High Accuracy, 3D Magnetometer +fsl,mc13892 MC13892: Power Management Integrated Circuit (PMIC) for i.MX35/51 +fsl,mma8450 MMA8450Q: Xtrinsic Low-power, 3-axis Xtrinsic Accelerometer +fsl,mma8452 MMA8452Q: 3-axis 12-bit / 8-bit Digital Accelerometer +fsl,mpr121 MPR121: Proximity Capacitive Touch Sensor Controller +fsl,sgtl5000 SGTL5000: Ultra Low-Power Audio Codec +gmt,g751 G751: Digital Temperature Sensor and Thermal Watchdog with Two-Wire Interface +infineon,slb9635tt Infineon SLB9635 (Soft-) I2C TPM (old protocol, max 100khz) +infineon,slb9645tt Infineon SLB9645 I2C TPM (new protocol, max 400khz) +isil,isl12057 Intersil ISL12057 I2C RTC Chip +isil,isl29028 Intersil ISL29028 Ambient Light and Proximity Sensor +maxim,ds1050 5 Bit Programmable, Pulse-Width Modulator +maxim,max1237 Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs +maxim,max6625 9-Bit/12-Bit Temperature Sensors with I²C-Compatible Serial Interface +mc,rv3029c2 Real Time Clock Module with I2C-Bus +national,lm63 Temperature sensor with integrated fan control +national,lm75 I2C TEMP SENSOR +national,lm80 Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor +national,lm85 Temperature sensor with integrated fan control +national,lm92 ±0.33°C Accurate, 12-Bit + Sign Temperature Sensor and Thermal Window Comparator with Two-Wire Interface +nuvoton,npct501 i2c trusted platform module (TPM) +nxp,pca9556 Octal SMBus and I2C registered interface +nxp,pca9557 8-bit I2C-bus and SMBus I/O port with reset +nxp,pcf8563 Real-time clock/calendar +nxp,pcf85063 Tiny Real-Time Clock +oki,ml86v7667 OKI ML86V7667 video decoder +ovti,ov5642 OV5642: Color CMOS QSXGA (5-megapixel) Image Sensor with OmniBSI and Embedded TrueFocus +pericom,pt7c4338 Real-time Clock Module +plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch +ramtron,24c64 i2c serial eeprom (24cxx) +ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC +samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) +sii,s35390a 2-wire CMOS real-time clock +skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply +st-micro,24c256 i2c serial eeprom (24cxx) +stm,m41t00 Serial Access TIMEKEEPER +stm,m41t62 Serial real-time clock (RTC) with alarm +stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS +taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface +ti,tsc2003 I2C Touch-Screen Controller +ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface +ti,tmp103 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface +ti,tmp275 Digital Temperature Sensor +winbond,wpct301 i2c trusted platform module (TPM) |