diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio')
7 files changed, 95 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/berlin2_adc.txt b/Documentation/devicetree/bindings/iio/adc/berlin2_adc.txt new file mode 100644 index 000000000..908334c6b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/berlin2_adc.txt @@ -0,0 +1,19 @@ +* Berlin Analog to Digital Converter (ADC) + +The Berlin ADC has 8 channels, with one connected to a temperature sensor. +It is part of the system controller register set. The ADC node should be a +sub-node of the system controller node. + +Required properties: +- compatible: must be "marvell,berlin2-adc" +- interrupts: the interrupts for the ADC and the temperature sensor +- interrupt-names: should be "adc" and "tsen" + +Example: + +adc: adc { + compatible = "marvell,berlin2-adc"; + interrupt-parent = <&sic>; + interrupts = <12>, <14>; + interrupt-names = "adc", "tsen"; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt index 42ca7deec..15ca6b479 100644 --- a/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc128s052.txt @@ -1,7 +1,7 @@ -* Texas Instruments' ADC128S052 ADC chip +* Texas Instruments' ADC128S052 and ADC122S021 ADC chip Required properties: - - compatible: Should be "ti,adc128s052" + - compatible: Should be "ti,adc128s052" or "ti,adc122s021" - reg: spi chip select number for the device - vref-supply: The regulator supply for ADC reference voltage diff --git a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt index 1a4a43d5c..3eb40e20c 100644 --- a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt @@ -11,6 +11,13 @@ Required properties: - clock-names: Must contain "adc", matching entry in the clocks property. - vref-supply: The regulator supply ADC reference voltage. +Recommended properties: +- fsl,adck-max-frequency: Maximum frequencies according to datasheets operating + requirements. Three values are required, depending on conversion mode: + - Frequency in normal mode (ADLPC=0, ADHSC=0) + - Frequency in high-speed mode (ADLPC=0, ADHSC=1) + - Frequency in low-power mode (ADLPC=1, ADHSC=0) + Example: adc0: adc@4003b000 { compatible = "fsl,vf610-adc"; @@ -18,5 +25,7 @@ adc0: adc@4003b000 { interrupts = <0 53 0x04>; clocks = <&clks VF610_CLK_ADC0>; clock-names = "adc"; + fsl,adck-max-frequency = <30000000>, <40000000>, + <20000000>; vref-supply = <®_vcc_3v3_mcu>; }; diff --git a/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt new file mode 100644 index 000000000..e4d8f1c52 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/imu/inv_mpu6050.txt @@ -0,0 +1,17 @@ +InvenSense MPU-6050 Six-Axis (Gyro + Accelerometer) MEMS MotionTracking Device + +http://www.invensense.com/mems/gyro/mpu6050.html + +Required properties: + - compatible : should be "invensense,mpu6050" + - reg : the I2C address of the sensor + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : interrupt mapping for GPIO IRQ + +Example: + mpu6050@68 { + compatible = "invensense,mpu6050"; + reg = <0x68>; + interrupt-parent = <&gpio1>; + interrupts = <18 1>; + }; diff --git a/Documentation/devicetree/bindings/iio/magnetometer/bmc150_magn.txt b/Documentation/devicetree/bindings/iio/magnetometer/bmc150_magn.txt new file mode 100644 index 000000000..9f263b7df --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/bmc150_magn.txt @@ -0,0 +1,22 @@ +* Bosch BMC150 magnetometer sensor + +http://ae-bst.resource.bosch.com/media/products/dokumente/bmc150/BST-BMC150-DS000-04.pdf + +Required properties: + + - compatible : should be "bosch,bmc150_magn" + - reg : the I2C address of the magnetometer + +Optional properties: + + - interrupt-parent : phandle to the parent interrupt controller + - interrupts : interrupt mapping for GPIO IRQ + +Example: + +bmc150_magn@12 { + compatible = "bosch,bmc150_magn"; + reg = <0x12>; + interrupt-parent = <&gpio1>; + interrupts = <0 1>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index d2aaca974..8a6be3bdf 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -30,6 +30,7 @@ Accelerometers: - st,lsm330d-accel - st,lsm330dl-accel - st,lsm330dlc-accel +- st,lis331dl-accel - st,lis331dlh-accel - st,lsm303dl-accel - st,lsm303dlm-accel @@ -45,6 +46,7 @@ Gyroscopes: - st,lsm330-gyro Magnetometers: +- st,lsm303dlh-magn - st,lsm303dlhc-magn - st,lsm303dlm-magn - st,lis3mdl-magn diff --git a/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt b/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt new file mode 100644 index 000000000..9be57b036 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt @@ -0,0 +1,24 @@ +* Melexis MLX90614 contactless IR temperature sensor + +http://melexis.com/Infrared-Thermometer-Sensors/Infrared-Thermometer-Sensors/MLX90614-615.aspx + +Required properties: + + - compatible: should be "melexis,mlx90614" + - reg: the I2C address of the sensor + +Optional properties: + + - wakeup-gpios: device tree identifier of the GPIO connected to the SDA line + to hold low in order to wake up the device. In normal operation, the + GPIO is set as input and will not interfere in I2C communication. There + is no need for a GPIO driving the SCL line. If no GPIO is given, power + management is disabled. + +Example: + +mlx90614@5a { + compatible = "melexis,mlx90614"; + reg = <0x5a>; + wakeup-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; +}; |