diff options
Diffstat (limited to 'Documentation/devicetree/bindings/input')
61 files changed, 2384 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/input/ads7846.txt b/Documentation/devicetree/bindings/input/ads7846.txt new file mode 100644 index 000000000..5f7619c22 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ads7846.txt @@ -0,0 +1,91 @@ +Device tree bindings for TI's ADS7843, ADS7845, ADS7846, ADS7873, TSC2046 +SPI driven touch screen controllers. + +The node for this driver must be a child node of a SPI controller, hence +all mandatory properties described in + + Documentation/devicetree/bindings/spi/spi-bus.txt + +must be specified. + +Additional required properties: + + compatible Must be one of the following, depending on the + model: + "ti,tsc2046" + "ti,ads7843" + "ti,ads7845" + "ti,ads7846" + "ti,ads7873" + + interrupt-parent + interrupts An interrupt node describing the IRQ line the chip's + !PENIRQ pin is connected to. + vcc-supply A regulator node for the supply voltage. + + +Optional properties: + + ti,vref-delay-usecs vref supply delay in usecs, 0 for + external vref (u16). + ti,vref-mv The VREF voltage, in millivolts (u16). + ti,keep-vref-on set to keep vref on for differential + measurements as well + ti,swap-xy swap x and y axis + ti,settle-delay-usec Settling time of the analog signals; + a function of Vcc and the capacitance + on the X/Y drivers. If set to non-zero, + two samples are taken with settle_delay + us apart, and the second one is used. + ~150 uSec with 0.01uF caps (u16). + ti,penirq-recheck-delay-usecs If set to non-zero, after samples are + taken this delay is applied and penirq + is rechecked, to help avoid false + events. This value is affected by the + material used to build the touch layer + (u16). + ti,x-plate-ohms Resistance of the X-plate, + in Ohms (u16). + ti,y-plate-ohms Resistance of the Y-plate, + in Ohms (u16). + ti,x-min Minimum value on the X axis (u16). + ti,y-min Minimum value on the Y axis (u16). + ti,x-max Maximum value on the X axis (u16). + ti,y-max Minimum value on the Y axis (u16). + ti,pressure-min Minimum reported pressure value + (threshold) - u16. + ti,pressure-max Maximum reported pressure value (u16). + ti,debounce-max Max number of additional readings per + sample (u16). + ti,debounce-tol Tolerance used for filtering (u16). + ti,debounce-rep Additional consecutive good readings + required after the first two (u16). + ti,pendown-gpio-debounce Platform specific debounce time for the + pendown-gpio (u32). + pendown-gpio GPIO handle describing the pin the !PENIRQ + line is connected to. + linux,wakeup use any event on touchscreen as wakeup event. + + +Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC:: + + spi_controller { + tsc2046@0 { + reg = <0>; /* CS0 */ + compatible = "ti,tsc2046"; + interrupt-parent = <&gpio1>; + interrupts = <8 0>; /* BOOT6 / GPIO 8 */ + spi-max-frequency = <1000000>; + pendown-gpio = <&gpio1 8 0>; + vcc-supply = <®_vcc3>; + + ti,x-min = /bits/ 16 <0>; + ti,x-max = /bits/ 16 <8000>; + ti,y-min = /bits/ 16 <0>; + ti,y-max = /bits/ 16 <4800>; + ti,x-plate-ohms = /bits/ 16 <40>; + ti,pressure-max = /bits/ 16 <255>; + + linux,wakeup; + }; + }; diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt new file mode 100644 index 000000000..185290651 --- /dev/null +++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt @@ -0,0 +1,32 @@ +Atmel maXTouch touchscreen/touchpad + +Required properties: +- compatible: + atmel,maxtouch + +- reg: The I2C address of the device + +- interrupts: The sink for the touchpad's IRQ output + See ../interrupt-controller/interrupts.txt + +Optional properties for main touchpad device: + +- linux,gpio-keymap: When enabled, the SPT_GPIOPWN_T19 object sends messages + on GPIO bit changes. An array of up to 8 entries can be provided + indicating the Linux keycode mapped to each bit of the status byte, + starting at the LSB. Linux keycodes are defined in + <dt-bindings/input/input.h>. + + Note: the numbering of the GPIOs and the bit they start at varies between + maXTouch devices. You must either refer to the documentation, or + experiment to determine which bit corresponds to which input. Use + KEY_RESERVED for unused padding values. + +Example: + + touch@4b { + compatible = "atmel,maxtouch"; + reg = <0x4b>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>; + }; diff --git a/Documentation/devicetree/bindings/input/brcm,bcm-keypad.txt b/Documentation/devicetree/bindings/input/brcm,bcm-keypad.txt new file mode 100644 index 000000000..b77f50bd6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/brcm,bcm-keypad.txt @@ -0,0 +1,108 @@ +* Broadcom Keypad Controller device tree bindings + +Broadcom Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. + +Required SoC Specific Properties: +- compatible: should be "brcm,bcm-keypad" + +- reg: physical base address of the controller and length of memory mapped + region. + +- interrupts: The interrupt number to the cpu. + +Board Specific Properties: +- keypad,num-rows: Number of row lines connected to the keypad + controller. + +- keypad,num-columns: Number of column lines connected to the + keypad controller. + +- col-debounce-filter-period: The debounce period for the Column filter. + + KEYPAD_DEBOUNCE_1_ms = 0 + KEYPAD_DEBOUNCE_2_ms = 1 + KEYPAD_DEBOUNCE_4_ms = 2 + KEYPAD_DEBOUNCE_8_ms = 3 + KEYPAD_DEBOUNCE_16_ms = 4 + KEYPAD_DEBOUNCE_32_ms = 5 + KEYPAD_DEBOUNCE_64_ms = 6 + KEYPAD_DEBOUNCE_128_ms = 7 + +- status-debounce-filter-period: The debounce period for the Status filter. + + KEYPAD_DEBOUNCE_1_ms = 0 + KEYPAD_DEBOUNCE_2_ms = 1 + KEYPAD_DEBOUNCE_4_ms = 2 + KEYPAD_DEBOUNCE_8_ms = 3 + KEYPAD_DEBOUNCE_16_ms = 4 + KEYPAD_DEBOUNCE_32_ms = 5 + KEYPAD_DEBOUNCE_64_ms = 6 + KEYPAD_DEBOUNCE_128_ms = 7 + +- row-output-enabled: An optional property indicating whether the row or + column is being used as output. If specified the row is being used + as the output. Else defaults to column. + +- pull-up-enabled: An optional property indicating the Keypad scan mode. + If specified implies the keypad scan pull-up has been enabled. + +- autorepeat: Boolean, Enable auto repeat feature of Linux input + subsystem (optional). + +- linux,keymap: The keymap for keys as described in the binding document + devicetree/bindings/input/matrix-keymap.txt. + +Example: +#include "dt-bindings/input/input.h" + +/ { + keypad: keypad@180ac000 { + /* Required SoC specific properties */ + compatible = "brcm,bcm-keypad"; + + /* Required Board specific properties */ + keypad,num-rows = <5>; + keypad,num-columns = <5>; + status = "okay"; + + linux,keymap = <MATRIX_KEY(0x00, 0x02, KEY_F) /* key_forward */ + MATRIX_KEY(0x00, 0x03, KEY_HOME) /* key_home */ + MATRIX_KEY(0x00, 0x04, KEY_M) /* key_message */ + MATRIX_KEY(0x01, 0x00, KEY_A) /* key_contacts */ + MATRIX_KEY(0x01, 0x01, KEY_1) /* key_1 */ + MATRIX_KEY(0x01, 0x02, KEY_2) /* key_2 */ + MATRIX_KEY(0x01, 0x03, KEY_3) /* key_3 */ + MATRIX_KEY(0x01, 0x04, KEY_S) /* key_speaker */ + MATRIX_KEY(0x02, 0x00, KEY_P) /* key_phone */ + MATRIX_KEY(0x02, 0x01, KEY_4) /* key_4 */ + MATRIX_KEY(0x02, 0x02, KEY_5) /* key_5 */ + MATRIX_KEY(0x02, 0x03, KEY_6) /* key_6 */ + MATRIX_KEY(0x02, 0x04, KEY_VOLUMEUP) /* key_vol_up */ + MATRIX_KEY(0x03, 0x00, KEY_C) /* key_call_log */ + MATRIX_KEY(0x03, 0x01, KEY_7) /* key_7 */ + MATRIX_KEY(0x03, 0x02, KEY_8) /* key_8 */ + MATRIX_KEY(0x03, 0x03, KEY_9) /* key_9 */ + MATRIX_KEY(0x03, 0x04, KEY_VOLUMEDOWN) /* key_vol_down */ + MATRIX_KEY(0x04, 0x00, KEY_H) /* key_headset */ + MATRIX_KEY(0x04, 0x01, KEY_KPASTERISK) /* key_* */ + MATRIX_KEY(0x04, 0x02, KEY_0) /* key_0 */ + MATRIX_KEY(0x04, 0x03, KEY_GRAVE) /* key_# */ + MATRIX_KEY(0x04, 0x04, KEY_MUTE) /* key_mute */ + >; + + /* Optional board specific properties */ + col-debounce-filter-period = <5>; + row-output-enabled; + pull-up-enabled; + + }; +}; diff --git a/Documentation/devicetree/bindings/input/cap11xx.txt b/Documentation/devicetree/bindings/input/cap11xx.txt new file mode 100644 index 000000000..7d0a30097 --- /dev/null +++ b/Documentation/devicetree/bindings/input/cap11xx.txt @@ -0,0 +1,59 @@ +Device tree bindings for Microchip CAP11xx based capacitive touch sensors + +The node for this device must be a child of a I2C controller node, as the +device communication via I2C only. + +Required properties: + + compatible: Must contain one of: + "microchip,cap1106" + "microchip,cap1126" + "microchip,cap1188" + + reg: The I2C slave address of the device. + + interrupts: Property describing the interrupt line the + device's ALERT#/CM_IRQ# pin is connected to. + The device only has one interrupt source. + +Optional properties: + + autorepeat: Enables the Linux input system's autorepeat + feature on the input device. + + microchip,sensor-gain: Defines the gain of the sensor circuitry. This + effectively controls the sensitivity, as a + smaller delta capacitance is required to + generate the same delta count values. + Valid values are 1, 2, 4, and 8. + By default, a gain of 1 is set. + + microchip,irq-active-high: By default the interrupt pin is active low + open drain. This property allows using the active + high push-pull output. + + linux,keycodes: Specifies an array of numeric keycode values to + be used for the channels. If this property is + omitted, KEY_A, KEY_B, etc are used as + defaults. The array must have exactly six + entries. + +Example: + +i2c_controller { + cap1106@28 { + compatible = "microchip,cap1106"; + interrupt-parent = <&gpio1>; + interrupts = <0 0>; + reg = <0x28>; + autorepeat; + microchip,sensor-gain = <2>; + + linux,keycodes = <103>, /* KEY_UP */ + <106>, /* KEY_RIGHT */ + <108>, /* KEY_DOWN */ + <105>, /* KEY_LEFT */ + <109>, /* KEY_PAGEDOWN */ + <104>; /* KEY_PAGEUP */ + }; +} diff --git a/Documentation/devicetree/bindings/input/clps711x-keypad.txt b/Documentation/devicetree/bindings/input/clps711x-keypad.txt new file mode 100644 index 000000000..e68d2bbc6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/clps711x-keypad.txt @@ -0,0 +1,27 @@ +* Cirrus Logic CLPS711X matrix keypad device tree bindings + +Required Properties: +- compatible: Shall contain "cirrus,clps711x-keypad". +- row-gpios: List of GPIOs used as row lines. +- poll-interval: Poll interval time in milliseconds. +- linux,keymap: The definition can be found at + bindings/input/matrix-keymap.txt. + +Optional Properties: +- autorepeat: Enable autorepeat feature. + +Example: + keypad { + compatible = "cirrus,ep7312-keypad", "cirrus,clps711x-keypad"; + autorepeat; + poll-interval = <120>; + row-gpios = <&porta 0 0>, + <&porta 1 0>; + + linux,keymap = < + MATRIX_KEY(0, 0, KEY_UP) + MATRIX_KEY(0, 1, KEY_DOWN) + MATRIX_KEY(1, 0, KEY_LEFT) + MATRIX_KEY(1, 1, KEY_RIGHT) + >; + }; diff --git a/Documentation/devicetree/bindings/input/cros-ec-keyb.txt b/Documentation/devicetree/bindings/input/cros-ec-keyb.txt new file mode 100644 index 000000000..0f6355ce3 --- /dev/null +++ b/Documentation/devicetree/bindings/input/cros-ec-keyb.txt @@ -0,0 +1,72 @@ +ChromeOS EC Keyboard + +Google's ChromeOS EC Keyboard is a simple matrix keyboard implemented on +a separate EC (Embedded Controller) device. It provides a message for reading +key scans from the EC. These are then converted into keycodes for processing +by the kernel. + +This binding is based on matrix-keymap.txt and extends/modifies it as follows: + +Required properties: +- compatible: "google,cros-ec-keyb" + +Optional properties: +- google,needs-ghost-filter: True to enable a ghost filter for the matrix +keyboard. This is recommended if the EC does not have its own logic or +hardware for this. + + +Example: + +cros-ec-keyb { + compatible = "google,cros-ec-keyb"; + keypad,num-rows = <8>; + keypad,num-columns = <13>; + google,needs-ghost-filter; + /* + * Keymap entries take the form of 0xRRCCKKKK where + * RR=Row CC=Column KKKK=Key Code + * The values below are for a US keyboard layout and + * are taken from the Linux driver. Note that the + * 102ND key is not used for US keyboards. + */ + linux,keymap = < + /* CAPSLCK F1 B F10 */ + 0x0001003a 0x0002003b 0x00030030 0x00040044 + /* N = R_ALT ESC */ + 0x00060031 0x0008000d 0x000a0064 0x01010001 + /* F4 G F7 H */ + 0x0102003e 0x01030022 0x01040041 0x01060023 + /* ' F9 BKSPACE L_CTRL */ + 0x01080028 0x01090043 0x010b000e 0x0200001d + /* TAB F3 T F6 */ + 0x0201000f 0x0202003d 0x02030014 0x02040040 + /* ] Y 102ND [ */ + 0x0205001b 0x02060015 0x02070056 0x0208001a + /* F8 GRAVE F2 5 */ + 0x02090042 0x03010029 0x0302003c 0x03030006 + /* F5 6 - \ */ + 0x0304003f 0x03060007 0x0308000c 0x030b002b + /* R_CTRL A D F */ + 0x04000061 0x0401001e 0x04020020 0x04030021 + /* S K J ; */ + 0x0404001f 0x04050025 0x04060024 0x04080027 + /* L ENTER Z C */ + 0x04090026 0x040b001c 0x0501002c 0x0502002e + /* V X , M */ + 0x0503002f 0x0504002d 0x05050033 0x05060032 + /* L_SHIFT / . SPACE */ + 0x0507002a 0x05080035 0x05090034 0x050B0039 + /* 1 3 4 2 */ + 0x06010002 0x06020004 0x06030005 0x06040003 + /* 8 7 0 9 */ + 0x06050009 0x06060008 0x0608000b 0x0609000a + /* L_ALT DOWN RIGHT Q */ + 0x060a0038 0x060b006c 0x060c006a 0x07010010 + /* E R W I */ + 0x07020012 0x07030013 0x07040011 0x07050017 + /* U R_SHIFT P O */ + 0x07060016 0x07070036 0x07080019 0x07090018 + /* UP LEFT */ + 0x070b0067 0x070c0069>; +}; diff --git a/Documentation/devicetree/bindings/input/e3x0-button.txt b/Documentation/devicetree/bindings/input/e3x0-button.txt new file mode 100644 index 000000000..751665e8e --- /dev/null +++ b/Documentation/devicetree/bindings/input/e3x0-button.txt @@ -0,0 +1,25 @@ +National Instruments Ettus Research USRP E3x0 button driver + +This module is part of the NI Ettus Research USRP E3x0 SDR. + +This module provides a simple power button event via two interrupts. + +Required properties: +- compatible: should be one of the following + - "ettus,e3x0-button": For devices such as the NI Ettus Research USRP E3x0 +- interrupt-parent: + - a phandle to the interrupt controller that it is attached to. +- interrupts: should be one of the following + - <0 30 1>, <0 31 1>: For devices such as the NI Ettus Research USRP E3x0 +- interrupt-names: should be one of the following + - "press", "release": For devices such as the NI Ettus Research USRP E3x0 + +Note: Interrupt numbers might vary depending on the FPGA configuration. + +Example: + button { + compatible = "ettus,e3x0-button"; + interrupt-parent = <&intc>; + interrupts = <0 30 1>, <0 31 1>; + interrupt-names = "press", "release"; + } diff --git a/Documentation/devicetree/bindings/input/elan_i2c.txt b/Documentation/devicetree/bindings/input/elan_i2c.txt new file mode 100644 index 000000000..ee3242c4b --- /dev/null +++ b/Documentation/devicetree/bindings/input/elan_i2c.txt @@ -0,0 +1,34 @@ +Elantech I2C Touchpad + +Required properties: +- compatible: must be "elan,ekth3000". +- reg: I2C address of the chip. +- interrupt-parent: a phandle for the interrupt controller (see interrupt + binding[0]). +- interrupts: interrupt to which the chip is connected (see interrupt + binding[0]). + +Optional properties: +- wakeup-source: touchpad can be used as a wakeup source. +- pinctrl-names: should be "default" (see pinctrl binding [1]). +- pinctrl-0: a phandle pointing to the pin settings for the device (see + pinctrl binding [1]). +- vcc-supply: a phandle for the regulator supplying 3.3V power. + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + &i2c1 { + /* ... */ + + touchpad@15 { + compatible = "elan,ekth3000"; + reg = <0x15>; + interrupt-parent = <&gpio4>; + interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/elants_i2c.txt b/Documentation/devicetree/bindings/input/elants_i2c.txt new file mode 100644 index 000000000..a765232e6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/elants_i2c.txt @@ -0,0 +1,33 @@ +Elantech I2C Touchscreen + +Required properties: +- compatible: must be "elan,ekth3500". +- reg: I2C address of the chip. +- interrupt-parent: a phandle for the interrupt controller (see interrupt + binding[0]). +- interrupts: interrupt to which the chip is connected (see interrupt + binding[0]). + +Optional properties: +- wakeup-source: touchscreen can be used as a wakeup source. +- pinctrl-names: should be "default" (see pinctrl binding [1]). +- pinctrl-0: a phandle pointing to the pin settings for the device (see + pinctrl binding [1]). + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + &i2c1 { + /* ... */ + + touchscreen@10 { + compatible = "elan,ekth3500"; + reg = <0x10>; + interrupt-parent = <&gpio4>; + interrupts = <0x0 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/fsl-mma8450.txt b/Documentation/devicetree/bindings/input/fsl-mma8450.txt new file mode 100644 index 000000000..0b96e5737 --- /dev/null +++ b/Documentation/devicetree/bindings/input/fsl-mma8450.txt @@ -0,0 +1,12 @@ +* Freescale MMA8450 3-Axis Accelerometer + +Required properties: +- compatible : "fsl,mma8450". +- reg: the I2C address of MMA8450 + +Example: + +accelerometer: mma8450@1c { + compatible = "fsl,mma8450"; + reg = <0x1c>; +}; diff --git a/Documentation/devicetree/bindings/input/gpio-beeper.txt b/Documentation/devicetree/bindings/input/gpio-beeper.txt new file mode 100644 index 000000000..a5086e37f --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-beeper.txt @@ -0,0 +1,13 @@ +* GPIO beeper device tree bindings + +Register a beeper connected to GPIO pin. + +Required properties: +- compatible: Should be "gpio-beeper". +- gpios: From common gpio binding; gpio connection to beeper enable pin. + +Example: + beeper: beeper { + compatible = "gpio-beeper"; + gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/input/gpio-keys-polled.txt b/Documentation/devicetree/bindings/input/gpio-keys-polled.txt new file mode 100644 index 000000000..313abefa3 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-keys-polled.txt @@ -0,0 +1,38 @@ +Device-Tree bindings for input/gpio_keys_polled.c keyboard driver + +Required properties: + - compatible = "gpio-keys-polled"; + - poll-interval: Poll interval time in milliseconds + +Optional properties: + - autorepeat: Boolean, Enable auto repeat feature of Linux input + subsystem. + +Each button (key) is represented as a sub-node of "gpio-keys-polled": +Subnode properties: + + - gpios: OF device-tree gpio specification. + - label: Descriptive name of the key. + - linux,code: Keycode to emit. + +Optional subnode-properties: + - linux,input-type: Specify event type this button/key generates. + If not specified defaults to <1> == EV_KEY. + - debounce-interval: Debouncing interval time in milliseconds. + If not specified defaults to 5. + - gpio-key,wakeup: Boolean, button can wake-up the system. + +Example nodes: + + gpio_keys_polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + autorepeat; + button@21 { + label = "GPIO Key UP"; + linux,code = <103>; + gpios = <&gpio1 0 1>; + }; + ... diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt new file mode 100644 index 000000000..44b705767 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt @@ -0,0 +1,48 @@ +Device-Tree bindings for input/gpio_keys.c keyboard driver + +Required properties: + - compatible = "gpio-keys"; + +Optional properties: + - autorepeat: Boolean, Enable auto repeat feature of Linux input + subsystem. + +Each button (key) is represented as a sub-node of "gpio-keys": +Subnode properties: + + - gpios: OF device-tree gpio specification. + - interrupts: the interrupt line for that input. + - label: Descriptive name of the key. + - linux,code: Keycode to emit. + +Note that either "interrupts" or "gpios" properties can be omitted, but not +both at the same time. Specifying both properties is allowed. + +Optional subnode-properties: + - linux,input-type: Specify event type this button/key generates. + If not specified defaults to <1> == EV_KEY. + - debounce-interval: Debouncing interval time in milliseconds. + If not specified defaults to 5. + - gpio-key,wakeup: Boolean, button can wake-up the system. + - linux,can-disable: Boolean, indicates that button is connected + to dedicated (not shared) interrupt which can be disabled to + suppress events from the button. + +Example nodes: + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + button@21 { + label = "GPIO Key UP"; + linux,code = <103>; + gpios = <&gpio1 0 1>; + }; + button@22 { + label = "GPIO Key DOWN"; + linux,code = <108>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + }; + ... diff --git a/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt new file mode 100644 index 000000000..ead641c65 --- /dev/null +++ b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt @@ -0,0 +1,46 @@ +* GPIO driven matrix keypad device tree bindings + +GPIO driven matrix keypad is used to interface a SoC with a matrix keypad. +The matrix keypad supports multiple row and column lines, a key can be +placed at each intersection of a unique row and a unique column. The matrix +keypad can sense a key-press and key-release by means of GPIO lines and +report the event using GPIO interrupts to the cpu. + +Required Properties: +- compatible: Should be "gpio-matrix-keypad" +- row-gpios: List of gpios used as row lines. The gpio specifier + for this property depends on the gpio controller to + which these row lines are connected. +- col-gpios: List of gpios used as column lines. The gpio specifier + for this property depends on the gpio controller to + which these column lines are connected. +- linux,keymap: The definition can be found at + bindings/input/matrix-keymap.txt + +Optional Properties: +- linux,no-autorepeat: do no enable autorepeat feature. +- linux,wakeup: use any event on keypad as wakeup event. +- debounce-delay-ms: debounce interval in milliseconds +- col-scan-delay-us: delay, measured in microseconds, that is needed + before we can scan keypad after activating column gpio + +Example: + matrix-keypad { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio2 25 0 + &gpio2 26 0 + &gpio2 27 0>; + + col-gpios = <&gpio2 21 0 + &gpio2 22 0>; + + linux,keymap = <0x0000008B + 0x0100009E + 0x02000069 + 0x0001006A + 0x0101001C + 0x0201006C>; + }; diff --git a/Documentation/devicetree/bindings/input/imx-keypad.txt b/Documentation/devicetree/bindings/input/imx-keypad.txt new file mode 100644 index 000000000..2ebaf7d26 --- /dev/null +++ b/Documentation/devicetree/bindings/input/imx-keypad.txt @@ -0,0 +1,53 @@ +* Freescale i.MX Keypad Port(KPP) device tree bindings + +The KPP is designed to interface with a keypad matrix with 2-point contact +or 3-point contact keys. The KPP is designed to simplify the software task +of scanning a keypad matrix. The KPP is capable of detecting, debouncing, +and decoding one or multiple keys pressed simultaneously on a keypad. + +Required SoC Specific Properties: +- compatible: Should be "fsl,<soc>-kpp". + +- reg: Physical base address of the KPP and length of memory mapped + region. + +- interrupts: The KPP interrupt number to the CPU(s). + +- clocks: The clock provided by the SoC to the KPP. Some SoCs use dummy +clock(The clock for the KPP is provided by the SoCs automatically). + +Required Board Specific Properties: +- pinctrl-names: The definition can be found at +pinctrl/pinctrl-bindings.txt. + +- pinctrl-0: The definition can be found at +pinctrl/pinctrl-bindings.txt. + +- linux,keymap: The definition can be found at +bindings/input/matrix-keymap.txt. + +Example: +kpp: kpp@73f94000 { + compatible = "fsl,imx51-kpp", "fsl,imx21-kpp"; + reg = <0x73f94000 0x4000>; + interrupts = <60>; + clocks = <&clks 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp_1>; + linux,keymap = <0x00000067 /* KEY_UP */ + 0x0001006c /* KEY_DOWN */ + 0x00020072 /* KEY_VOLUMEDOWN */ + 0x00030066 /* KEY_HOME */ + 0x0100006a /* KEY_RIGHT */ + 0x01010069 /* KEY_LEFT */ + 0x0102001c /* KEY_ENTER */ + 0x01030073 /* KEY_VOLUMEUP */ + 0x02000040 /* KEY_F6 */ + 0x02010042 /* KEY_F8 */ + 0x02020043 /* KEY_F9 */ + 0x02030044 /* KEY_F10 */ + 0x0300003b /* KEY_F1 */ + 0x0301003c /* KEY_F2 */ + 0x0302003d /* KEY_F3 */ + 0x03030074>; /* KEY_POWER */ +}; diff --git a/Documentation/devicetree/bindings/input/input-reset.txt b/Documentation/devicetree/bindings/input/input-reset.txt new file mode 100644 index 000000000..2bb2626fd --- /dev/null +++ b/Documentation/devicetree/bindings/input/input-reset.txt @@ -0,0 +1,33 @@ +Input: sysrq reset sequence + +A simple binding to represent a set of keys as described in +include/uapi/linux/input.h. This is to communicate a sequence of keys to the +sysrq driver. Upon holding the keys for a specified amount of time (if +specified) the system is sync'ed and reset. + +Key sequences are global to the system but all the keys in a set must be coming +from the same input device. + +The /chosen node should contain a 'linux,sysrq-reset-seq' child node to define +a set of keys. + +Required property: +sysrq-reset-seq: array of Linux keycodes, one keycode per cell. + +Optional property: +timeout-ms: duration keys must be pressed together in milliseconds before +generating a sysrq. If omitted the system is rebooted immediately when a valid +sequence has been recognized. + +Example: + + chosen { + linux,sysrq-reset-seq { + keyset = <0x03 + 0x04 + 0x0a>; + timeout-ms = <3000>; + }; + }; + +Would represent KEY_2, KEY_3 and KEY_9. diff --git a/Documentation/devicetree/bindings/input/lpc32xx-key.txt b/Documentation/devicetree/bindings/input/lpc32xx-key.txt new file mode 100644 index 000000000..bcf62f856 --- /dev/null +++ b/Documentation/devicetree/bindings/input/lpc32xx-key.txt @@ -0,0 +1,31 @@ +NXP LPC32xx Key Scan Interface + +This binding is based on the matrix-keymap binding with the following +changes: + +Required Properties: +- compatible: Should be "nxp,lpc3220-key" +- reg: Physical base address of the controller and length of memory mapped + region. +- interrupts: The interrupt number to the cpu. +- nxp,debounce-delay-ms: Debounce delay in ms +- nxp,scan-delay-ms: Repeated scan period in ms +- linux,keymap: the key-code to be reported when the key is pressed + and released, see also + Documentation/devicetree/bindings/input/matrix-keymap.txt + +Note: keypad,num-rows and keypad,num-columns are required, and must be equal +since LPC32xx only supports square matrices + +Example: + + key@40050000 { + compatible = "nxp,lpc3220-key"; + reg = <0x40050000 0x1000>; + interrupts = <54 0>; + keypad,num-rows = <1>; + keypad,num-columns = <1>; + nxp,debounce-delay-ms = <3>; + nxp,scan-delay-ms = <34>; + linux,keymap = <0x00000002>; + }; diff --git a/Documentation/devicetree/bindings/input/matrix-keymap.txt b/Documentation/devicetree/bindings/input/matrix-keymap.txt new file mode 100644 index 000000000..c54919fad --- /dev/null +++ b/Documentation/devicetree/bindings/input/matrix-keymap.txt @@ -0,0 +1,27 @@ +A simple common binding for matrix-connected key boards. Currently targeted at +defining the keys in the scope of linux key codes since that is a stable and +standardized interface at this time. + +Required properties: +- linux,keymap: an array of packed 1-cell entries containing the equivalent + of row, column and linux key-code. The 32-bit big endian cell is packed + as: + row << 24 | column << 16 | key-code + +Optional properties: +Properties for the number of rows and columns are optional because some +drivers will use fixed values for these. +- keypad,num-rows: Number of row lines connected to the keypad controller. +- keypad,num-columns: Number of column lines connected to the keypad + controller. + +Some users of this binding might choose to specify secondary keymaps for +cases where there is a modifier key such as a Fn key. Proposed names +for said properties are "linux,fn-keymap" or with another descriptive +word for the modifier other from "Fn". + +Example: + linux,keymap = < 0x00030012 + 0x0102003a >; + keypad,num-rows = <2>; + keypad,num-columns = <8>; diff --git a/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt new file mode 100644 index 000000000..0382b8bd6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/nvidia,tegra20-kbc.txt @@ -0,0 +1,54 @@ +* Tegra keyboard controller +The key controller has maximum 24 pins to make matrix keypad. Any pin +can be configured as row or column. The maximum column pin can be 8 +and maximum row pins can be 16 for Tegra20/Tegra30. + +Required properties: +- compatible: "nvidia,tegra20-kbc" +- reg: Register base address of KBC. +- interrupts: Interrupt number for the KBC. +- nvidia,kbc-row-pins: The KBC pins which are configured as row. This is an + array of pin numbers which is used as rows. +- nvidia,kbc-col-pins: The KBC pins which are configured as column. This is an + array of pin numbers which is used as column. +- linux,keymap: The keymap for keys as described in the binding document + devicetree/bindings/input/matrix-keymap.txt. +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - kbc + +Optional properties, in addition to those specified by the shared +matrix-keyboard bindings: + +- linux,fn-keymap: a second keymap, same specification as the + matrix-keyboard-controller spec but to be used when the KEY_FN modifier + key is pressed. +- nvidia,debounce-delay-ms: delay in milliseconds per row scan for debouncing +- nvidia,repeat-delay-ms: delay in milliseconds before repeat starts +- nvidia,ghost-filter: enable ghost filtering for this device +- nvidia,wakeup-source: configure keyboard as a wakeup source for suspend/resume + +Example: + +keyboard: keyboard { + compatible = "nvidia,tegra20-kbc"; + reg = <0x7000e200 0x100>; + interrupts = <0 85 0x04>; + clocks = <&tegra_car 36>; + resets = <&tegra_car 36>; + reset-names = "kbc"; + nvidia,ghost-filter; + nvidia,debounce-delay-ms = <640>; + nvidia,kbc-row-pins = <0 1 2>; /* pin 0, 1, 2 as rows */ + nvidia,kbc-col-pins = <11 12 13>; /* pin 11, 12, 13 as columns */ + linux,keymap = <0x00000074 + 0x00010067 + 0x00020066 + 0x01010068 + 0x02000069 + 0x02010070 + 0x02020071>; +}; diff --git a/Documentation/devicetree/bindings/input/omap-keypad.txt b/Documentation/devicetree/bindings/input/omap-keypad.txt new file mode 100644 index 000000000..34ed1c60f --- /dev/null +++ b/Documentation/devicetree/bindings/input/omap-keypad.txt @@ -0,0 +1,28 @@ +* TI's Keypad Controller device tree bindings + +TI's Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "ti,omap4-keypad": For controllers compatible with omap4 keypad + controller. + +Optional Properties specific to linux: +- linux,keypad-no-autorepeat: do no enable autorepeat feature. + +Example: + keypad@4ae1c000{ + compatible = "ti,omap4-keypad"; + keypad,num-rows = <2>; + keypad,num-columns = <8>; + linux,keypad-no-autorepeat; + }; diff --git a/Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt b/Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt new file mode 100644 index 000000000..3029c5694 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ps2keyb-mouse-apbps2.txt @@ -0,0 +1,16 @@ +Aeroflex Gaisler APBPS2 PS/2 Core, supporting Keyboard or Mouse. + +The APBPS2 PS/2 core is available in the GRLIB VHDL IP core library. + +Note: In the ordinary environment for the APBPS2 core, a LEON SPARC system, +these properties are built from information in the AMBA plug&play and from +bootloader settings. + +Required properties: + +- name : Should be "GAISLER_APBPS2" or "01_060" +- reg : Address and length of the register set for the device +- interrupts : Interrupt numbers for this device + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/input/pwm-beeper.txt b/Documentation/devicetree/bindings/input/pwm-beeper.txt new file mode 100644 index 000000000..be332ae4f --- /dev/null +++ b/Documentation/devicetree/bindings/input/pwm-beeper.txt @@ -0,0 +1,7 @@ +* PWM beeper device tree bindings + +Registers a PWM device as beeper. + +Required properties: +- compatible: should be "pwm-beeper" +- pwms: phandle to the physical PWM device diff --git a/Documentation/devicetree/bindings/input/pxa27x-keypad.txt b/Documentation/devicetree/bindings/input/pxa27x-keypad.txt new file mode 100644 index 000000000..f8674f7e5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/pxa27x-keypad.txt @@ -0,0 +1,60 @@ +* Marvell PXA Keypad controller + +Required Properties +- compatible : should be "marvell,pxa27x-keypad" +- reg : Address and length of the register set for the device +- interrupts : The interrupt for the keypad controller +- marvell,debounce-interval : How long time the key will be + recognized when it is pressed. It is a u32 value, and bit[31:16] + is debounce interval for direct key and bit[15:0] is debounce + interval for matrix key. The value is in binary number of 2ms + +Optional Properties For Matrix Keyes +Please refer to matrix-keymap.txt + +Optional Properties for Direct Keyes +- marvell,direct-key-count : How many direct keyes are used. +- marvell,direct-key-mask : The mask indicates which keyes + are used. If bit[X] of the mask is set, the direct key X + is used. +- marvell,direct-key-low-active : Direct key status register + tells the level of pins that connects to the direct keyes. + When this property is set, it means that when the pin level + is low, the key is pressed(active). +- marvell,direct-key-map : It is a u16 array. Each item indicates + the linux key-code for the direct key. + +Optional Properties For Rotary +- marvell,rotary0 : It is a u32 value. Bit[31:16] is the + linux key-code for rotary up. Bit[15:0] is the linux key-code + for rotary down. It is for rotary 0. +- marvell,rotary1 : Same as marvell,rotary0. It is for rotary 1. +- marvell,rotary-rel-key : When rotary is used for relative axes + in the device, the value indicates the key-code for relative + axes measurement in the device. It is a u32 value. Bit[31:16] + is for rotary 1, and Bit[15:0] is for rotary 0. + +Examples: + keypad: keypad@d4012000 { + keypad,num-rows = <3>; + keypad,num-columns = <5>; + linux,keymap = <0x0000000e /* KEY_BACKSPACE */ + 0x0001006b /* KEY_END */ + 0x00020061 /* KEY_RIGHTCTRL */ + 0x0003000b /* KEY_0 */ + 0x00040002 /* KEY_1 */ + 0x0100008b /* KEY_MENU */ + 0x01010066 /* KEY_HOME */ + 0x010200e7 /* KEY_SEND */ + 0x01030009 /* KEY_8 */ + 0x0104000a /* KEY_9 */ + 0x02000160 /* KEY_OK */ + 0x02010003 /* KEY_2 */ + 0x02020004 /* KEY_3 */ + 0x02030005 /* KEY_4 */ + 0x02040006>; /* KEY_5 */ + marvell,rotary0 = <0x006c0067>; /* KEY_UP & KEY_DOWN */ + marvell,direct-key-count = <1>; + marvell,direct-key-map = <0x001c>; + marvell,debounce-interval = <0x001e001e>; + }; diff --git a/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt b/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt new file mode 100644 index 000000000..07bf55f6e --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt @@ -0,0 +1,43 @@ +Qualcomm PM8941 PMIC Power Key + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8941-pwrkey" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: base address of registers for block + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: key change interrupt; The format of the specifier is + defined by the binding document describing the node's + interrupt parent. + +- debounce: + Usage: optional + Value type: <u32> + Definition: time in microseconds that key must be pressed or released + for state change interrupt to trigger. + +- bias-pull-up: + Usage: optional + Value type: <empty> + Definition: presence of this property indicates that the KPDPWR_N pin + should be configured for pull up. + +EXAMPLE + + pwrkey@800 { + compatible = "qcom,pm8941-pwrkey"; + reg = <0x800>; + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + }; diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt new file mode 100644 index 000000000..7d8cb9283 --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt @@ -0,0 +1,89 @@ +Qualcomm PM8xxx PMIC Keypad + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058-keypad" + "qcom,pm8921-keypad" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: address of keypad control register + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: the first interrupt specifies the key sense interrupt + and the second interrupt specifies the key stuck interrupt. + The format of the specifier is defined by the binding + document describing the node's interrupt parent. + +- linux,keymap: + Usage: required + Value type: <prop-encoded-array> + Definition: the linux keymap. More information can be found in + input/matrix-keymap.txt. + +- linux,keypad-no-autorepeat: + Usage: optional + Value type: <bool> + Definition: don't enable autorepeat feature. + +- linux,keypad-wakeup: + Usage: optional + Value type: <bool> + Definition: use any event on keypad as wakeup event. + +- keypad,num-rows: + Usage: required + Value type: <u32> + Definition: number of rows in the keymap. More information can be found + in input/matrix-keymap.txt. + +- keypad,num-columns: + Usage: required + Value type: <u32> + Definition: number of columns in the keymap. More information can be + found in input/matrix-keymap.txt. + +- debounce: + Usage: optional + Value type: <u32> + Definition: time in microseconds that key must be pressed or release + for key sense interrupt to trigger. + +- scan-delay: + Usage: optional + Value type: <u32> + Definition: time in microseconds to pause between successive scans + of the matrix array. + +- row-hold: + Usage: optional + Value type: <u32> + Definition: time in nanoseconds to pause between scans of each row in + the matrix array. + +EXAMPLE + + keypad@148 { + compatible = "qcom,pm8921-keypad"; + reg = <0x148>; + interrupt-parent = <&pmicintc>; + interrupts = <74 1>, <75 1>; + linux,keymap = < + MATRIX_KEY(0, 0, KEY_VOLUMEUP) + MATRIX_KEY(0, 1, KEY_VOLUMEDOWN) + MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS) + MATRIX_KEY(0, 3, KEY_CAMERA) + >; + keypad,num-rows = <1>; + keypad,num-columns = <5>; + debounce = <15>; + scan-delay = <32>; + row-hold = <91500>; + }; diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt new file mode 100644 index 000000000..588536cc9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-pwrkey.txt @@ -0,0 +1,46 @@ +Qualcomm PM8xxx PMIC Power Key + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058-pwrkey" + "qcom,pm8921-pwrkey" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: address of power key control register + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: the first interrupt specifies the key release interrupt + and the second interrupt specifies the key press interrupt. + The format of the specifier is defined by the binding + document describing the node's interrupt parent. + +- debounce: + Usage: optional + Value type: <u32> + Definition: time in microseconds that key must be pressed or release + for state change interrupt to trigger. + +- pull-up: + Usage: optional + Value type: <empty> + Definition: presence of this property indicates that the KPDPWR_N pin + should be configured for pull up. + +EXAMPLE + + pwrkey@1c { + compatible = "qcom,pm8921-pwrkey"; + reg = <0x1c>; + interrupt-parent = <&pmicintc>; + interrupts = <50 1>, <51 1>; + debounce = <15625>; + pull-up; + }; diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt new file mode 100644 index 000000000..4ed467b1e --- /dev/null +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.txt @@ -0,0 +1,22 @@ +Qualcomm PM8xxx PMIC Vibrator + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058-vib" + "qcom,pm8921-vib" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: address of vibration control register + +EXAMPLE + + vibrator@4a { + compatible = "qcom,pm8058-vib"; + reg = <0x4a>; + }; diff --git a/Documentation/devicetree/bindings/input/regulator-haptic.txt b/Documentation/devicetree/bindings/input/regulator-haptic.txt new file mode 100644 index 000000000..3ed1c7eb2 --- /dev/null +++ b/Documentation/devicetree/bindings/input/regulator-haptic.txt @@ -0,0 +1,21 @@ +* Regulator Haptic Device Tree Bindings + +Required Properties: + - compatible : Should be "regulator-haptic" + - haptic-supply : Power supply to the haptic motor. + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + + - max-microvolt : The maximum voltage value supplied to the haptic motor. + [The unit of the voltage is a micro] + + - min-microvolt : The minimum voltage value supplied to the haptic motor. + [The unit of the voltage is a micro] + +Example: + + haptics { + compatible = "regulator-haptic"; + haptic-supply = <&motor_regulator>; + max-microvolt = <2700000>; + min-microvolt = <1100000>; + }; diff --git a/Documentation/devicetree/bindings/input/rotary-encoder.txt b/Documentation/devicetree/bindings/input/rotary-encoder.txt new file mode 100644 index 000000000..331549593 --- /dev/null +++ b/Documentation/devicetree/bindings/input/rotary-encoder.txt @@ -0,0 +1,36 @@ +Rotary encoder DT bindings + +Required properties: +- gpios: a spec for two GPIOs to be used + +Optional properties: +- linux,axis: the input subsystem axis to map to this rotary encoder. + Defaults to 0 (ABS_X / REL_X) +- rotary-encoder,steps: Number of steps in a full turnaround of the + encoder. Only relevant for absolute axis. Defaults to 24 which is a + typical value for such devices. +- rotary-encoder,relative-axis: register a relative axis rather than an + absolute one. Relative axis will only generate +1/-1 events on the input + device, hence no steps need to be passed. +- rotary-encoder,rollover: Automatic rollove when the rotary value becomes + greater than the specified steps or smaller than 0. For absolute axis only. +- rotary-encoder,half-period: Makes the driver work on half-period mode. + +See Documentation/input/rotary-encoder.txt for more information. + +Example: + + rotary@0 { + compatible = "rotary-encoder"; + gpios = <&gpio 19 1>, <&gpio 20 0>; /* GPIO19 is inverted */ + linux,axis = <0>; /* REL_X */ + rotary-encoder,relative-axis; + }; + + rotary@1 { + compatible = "rotary-encoder"; + gpios = <&gpio 21 0>, <&gpio 22 0>; + linux,axis = <1>; /* ABS_Y */ + rotary-encoder,steps = <24>; + rotary-encoder,rollover; + }; diff --git a/Documentation/devicetree/bindings/input/samsung-keypad.txt b/Documentation/devicetree/bindings/input/samsung-keypad.txt new file mode 100644 index 000000000..942d071ba --- /dev/null +++ b/Documentation/devicetree/bindings/input/samsung-keypad.txt @@ -0,0 +1,74 @@ +* Samsung's Keypad Controller device tree bindings + +Samsung's Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "samsung,s3c6410-keypad": For controllers compatible with s3c6410 keypad + controller. + - "samsung,s5pv210-keypad": For controllers compatible with s5pv210 keypad + controller. + +- reg: physical base address of the controller and length of memory mapped + region. + +- interrupts: The interrupt number to the cpu. + +Required Board Specific Properties: +- samsung,keypad-num-rows: Number of row lines connected to the keypad + controller. + +- samsung,keypad-num-columns: Number of column lines connected to the + keypad controller. + +- Keys represented as child nodes: Each key connected to the keypad + controller is represented as a child node to the keypad controller + device node and should include the following properties. + - keypad,row: the row number to which the key is connected. + - keypad,column: the column number to which the key is connected. + - linux,code: the key-code to be reported when the key is pressed + and released. + +- pinctrl-0: Should specify pin control groups used for this controller. +- pinctrl-names: Should contain only one value - "default". + +Optional Properties specific to linux: +- linux,keypad-no-autorepeat: do no enable autorepeat feature. +- linux,keypad-wakeup: use any event on keypad as wakeup event. + + +Example: + keypad@100A0000 { + compatible = "samsung,s5pv210-keypad"; + reg = <0x100A0000 0x100>; + interrupts = <173>; + samsung,keypad-num-rows = <2>; + samsung,keypad-num-columns = <8>; + linux,input-no-autorepeat; + linux,input-wakeup; + + pinctrl-names = "default"; + pinctrl-0 = <&keypad_rows &keypad_columns>; + + key_1 { + keypad,row = <0>; + keypad,column = <3>; + linux,code = <2>; + }; + + key_2 { + keypad,row = <0>; + keypad,column = <4>; + linux,code = <3>; + }; + + key_3 { + keypad,row = <0>; + keypad,column = <5>; + linux,code = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/spear-keyboard.txt b/Documentation/devicetree/bindings/input/spear-keyboard.txt new file mode 100644 index 000000000..4a846d26d --- /dev/null +++ b/Documentation/devicetree/bindings/input/spear-keyboard.txt @@ -0,0 +1,20 @@ +* SPEAr keyboard controller + +Required properties: +- compatible: "st,spear300-kbd" + +Optional properties, in addition to those specified by the shared +matrix-keyboard bindings: +- autorepeat: bool: enables key autorepeat +- st,mode: keyboard mode: 0 - 9x9, 1 - 6x6, 2 - 2x2 + +Example: + +kbd@fc400000 { + compatible = "st,spear300-kbd"; + reg = <0xfc400000 0x100>; + linux,keymap = < 0x00030012 + 0x0102003a >; + autorepeat; + st,mode = <0>; +}; diff --git a/Documentation/devicetree/bindings/input/st-keyscan.txt b/Documentation/devicetree/bindings/input/st-keyscan.txt new file mode 100644 index 000000000..51eb428e5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/st-keyscan.txt @@ -0,0 +1,60 @@ +* ST Keyscan controller Device Tree bindings + +The ST keyscan controller Device Tree binding is based on the +matrix-keymap. + +Required properties: +- compatible: "st,sti-keyscan" + +- reg: Register base address and size of st-keyscan controller. + +- interrupts: Interrupt number for the st-keyscan controller. + +- clocks: Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + +- pinctrl: Should specify pin control groups used for this controller. + See ../pinctrl/pinctrl-bindings.txt for details. + +- linux,keymap: The keymap for keys as described in the binding document + devicetree/bindings/input/matrix-keymap.txt. + +- keypad,num-rows: Number of row lines connected to the keypad controller. + +- keypad,num-columns: Number of column lines connected to the keypad + controller. + +Optional property: +- st,debounce_us: Debouncing interval time in microseconds + +Example: + +keyscan: keyscan@fe4b0000 { + compatible = "st,sti-keyscan"; + reg = <0xfe4b0000 0x2000>; + interrupts = <GIC_SPI 212 IRQ_TYPE_NONE>; + clocks = <&CLK_SYSIN>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_keyscan>; + + keypad,num-rows = <4>; + keypad,num-columns = <4>; + st,debounce_us = <5000>; + + linux,keymap = < MATRIX_KEY(0x00, 0x00, KEY_F13) + MATRIX_KEY(0x00, 0x01, KEY_F9) + MATRIX_KEY(0x00, 0x02, KEY_F5) + MATRIX_KEY(0x00, 0x03, KEY_F1) + MATRIX_KEY(0x01, 0x00, KEY_F14) + MATRIX_KEY(0x01, 0x01, KEY_F10) + MATRIX_KEY(0x01, 0x02, KEY_F6) + MATRIX_KEY(0x01, 0x03, KEY_F2) + MATRIX_KEY(0x02, 0x00, KEY_F15) + MATRIX_KEY(0x02, 0x01, KEY_F11) + MATRIX_KEY(0x02, 0x02, KEY_F7) + MATRIX_KEY(0x02, 0x03, KEY_F3) + MATRIX_KEY(0x03, 0x00, KEY_F16) + MATRIX_KEY(0x03, 0x01, KEY_F12) + MATRIX_KEY(0x03, 0x02, KEY_F8) + MATRIX_KEY(0x03, 0x03, KEY_F4) >; + }; diff --git a/Documentation/devicetree/bindings/input/stmpe-keypad.txt b/Documentation/devicetree/bindings/input/stmpe-keypad.txt new file mode 100644 index 000000000..12bb771d6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/stmpe-keypad.txt @@ -0,0 +1,41 @@ +* STMPE Keypad + +Required properties: + - compatible : "st,stmpe-keypad" + - linux,keymap : See ./matrix-keymap.txt + +Optional properties: + - debounce-interval : Debouncing interval time in milliseconds + - st,scan-count : Scanning cycles elapsed before key data is updated + - st,no-autorepeat : If specified device will not autorepeat + - keypad,num-rows : See ./matrix-keymap.txt + - keypad,num-columns : See ./matrix-keymap.txt + +Example: + + stmpe_keypad { + compatible = "st,stmpe-keypad"; + + debounce-interval = <64>; + st,scan-count = <8>; + st,no-autorepeat; + + linux,keymap = <0x205006b + 0x4010074 + 0x3050072 + 0x1030004 + 0x502006a + 0x500000a + 0x5008b + 0x706001c + 0x405000b + 0x6070003 + 0x3040067 + 0x303006c + 0x60400e7 + 0x602009e + 0x4020073 + 0x5050002 + 0x4030069 + 0x3020008>; + }; diff --git a/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt new file mode 100644 index 000000000..b9c32f6fd --- /dev/null +++ b/Documentation/devicetree/bindings/input/sun4i-lradc-keys.txt @@ -0,0 +1,62 @@ +Allwinner sun4i low res adc attached tablet keys +------------------------------------------------ + +Required properties: + - compatible: "allwinner,sun4i-a10-lradc-keys" + - reg: mmio address range of the chip + - interrupts: interrupt to which the chip is connected + - vref-supply: powersupply for the lradc reference voltage + +Each key is represented as a sub-node of "allwinner,sun4i-a10-lradc-keys": + +Required subnode-properties: + - label: Descriptive name of the key. + - linux,code: Keycode to emit. + - channel: Channel this key is attached to, mut be 0 or 1. + - voltage: Voltage in µV at lradc input when this key is pressed. + +Example: + +#include <dt-bindings/input/input.h> + + lradc: lradc@01c22800 { + compatible = "allwinner,sun4i-a10-lradc-keys"; + reg = <0x01c22800 0x100>; + interrupts = <31>; + vref-supply = <®_vcc3v0>; + + button@191 { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + channel = <0>; + voltage = <191274>; + }; + + button@392 { + label = "Volume Down"; + linux,code = <KEY_VOLUMEDOWN>; + channel = <0>; + voltage = <392644>; + }; + + button@601 { + label = "Menu"; + linux,code = <KEY_MENU>; + channel = <0>; + voltage = <601151>; + }; + + button@795 { + label = "Enter"; + linux,code = <KEY_ENTER>; + channel = <0>; + voltage = <795090>; + }; + + button@987 { + label = "Home"; + linux,code = <KEY_HOMEPAGE>; + channel = <0>; + voltage = <987387>; + }; + }; diff --git a/Documentation/devicetree/bindings/input/tca8418_keypad.txt b/Documentation/devicetree/bindings/input/tca8418_keypad.txt new file mode 100644 index 000000000..255185009 --- /dev/null +++ b/Documentation/devicetree/bindings/input/tca8418_keypad.txt @@ -0,0 +1,10 @@ +This binding is based on the matrix-keymap binding with the following +changes: + +keypad,num-rows and keypad,num-columns are required. + +Required properties: +- compatible: "ti,tca8418" +- reg: the I2C address +- interrupts: IRQ line number, should trigger on falling edge +- linux,keymap: Keys definitions, see keypad-matrix. diff --git a/Documentation/devicetree/bindings/input/ti,drv260x.txt b/Documentation/devicetree/bindings/input/ti,drv260x.txt new file mode 100644 index 000000000..ee09c8f44 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv260x.txt @@ -0,0 +1,50 @@ +* Texas Instruments - drv260x Haptics driver family + +Required properties: + - compatible - One of: + "ti,drv2604" - DRV2604 + "ti,drv2605" - DRV2605 + "ti,drv2605l" - DRV2605L + - reg - I2C slave address + - vbat-supply - Required supply regulator + - mode - Power up mode of the chip (defined in include/dt-bindings/input/ti-drv260x.h) + DRV260X_LRA_MODE - Linear Resonance Actuator mode (Piezoelectric) + DRV260X_LRA_NO_CAL_MODE - This is a LRA Mode but there is no calibration + sequence during init. And the device is configured for real + time playback mode (RTP mode). + DRV260X_ERM_MODE - Eccentric Rotating Mass mode (Rotary vibrator) + - library-sel - These are ROM based waveforms pre-programmed into the IC. + This should be set to set the library to use at power up. + (defined in include/dt-bindings/input/ti-drv260x.h) + DRV260X_LIB_EMPTY - Do not use a pre-programmed library + DRV260X_ERM_LIB_A - Pre-programmed Library + DRV260X_ERM_LIB_B - Pre-programmed Library + DRV260X_ERM_LIB_C - Pre-programmed Library + DRV260X_ERM_LIB_D - Pre-programmed Library + DRV260X_ERM_LIB_E - Pre-programmed Library + DRV260X_ERM_LIB_F - Pre-programmed Library + DRV260X_LIB_LRA - Pre-programmed LRA Library + +Optional properties: + - enable-gpio - gpio pin to enable/disable the device. + - vib-rated-mv - The rated voltage of the actuator in millivolts. + If this is not set then the value will be defaulted to + 3.2 v. + - vib-overdrive-mv - The overdrive voltage of the actuator in millivolts. + If this is not set then the value will be defaulted to + 3.2 v. +Example: + +haptics: haptics@5a { + compatible = "ti,drv2605l"; + reg = <0x5a>; + vbat-supply = <&vbat>; + enable-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>; + mode = <DRV260X_LRA_MODE>; + library-sel = <DRV260X_LIB_LRA>; + vib-rated-mv = <3200>; + vib-overdriver-mv = <3200>; +} + +For more product information please see the link below: +http://www.ti.com/product/drv2605 diff --git a/Documentation/devicetree/bindings/input/ti,drv2667.txt b/Documentation/devicetree/bindings/input/ti,drv2667.txt new file mode 100644 index 000000000..996382cf9 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,drv2667.txt @@ -0,0 +1,17 @@ +* Texas Instruments - drv2667 Haptics driver + +Required properties: + - compatible - "ti,drv2667" - DRV2667 + - reg - I2C slave address + - vbat-supply - Required supply regulator + +Example: + +haptics: haptics@59 { + compatible = "ti,drv2667"; + reg = <0x59>; + vbat-supply = <&vbat>; +}; + +For more product information please see the link below: +http://www.ti.com/product/drv2667 diff --git a/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt b/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt new file mode 100644 index 000000000..513d94d6e --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt @@ -0,0 +1,60 @@ +TI-NSPIRE Keypad + +Required properties: +- compatible: Compatible property value should be "ti,nspire-keypad". + +- reg: Physical base address of the peripheral and length of memory mapped + region. + +- interrupts: The interrupt number for the peripheral. + +- scan-interval: How often to scan in us. Based on a APB speed of 33MHz, the + maximum and minimum delay time is ~2000us and ~500us respectively + +- row-delay: How long to wait before scanning each row. + +- clocks: The clock this peripheral is attached to. + +- linux,keymap: The keymap to use + (see Documentation/devicetree/bindings/input/matrix-keymap.txt) + +Optional properties: +- active-low: Specify that the keypad is active low (i.e. logical low signifies + a key press). + +Example: + +input { + compatible = "ti,nspire-keypad"; + reg = <0x900E0000 0x1000>; + interrupts = <16>; + + scan-interval = <1000>; + row-delay = <200>; + + clocks = <&apb_pclk>; + + linux,keymap = < + 0x0000001c 0x0001001c 0x00040039 + 0x0005002c 0x00060015 0x0007000b + 0x0008000f 0x0100002d 0x01010011 + 0x0102002f 0x01030004 0x01040016 + 0x01050014 0x0106001f 0x01070002 + 0x010a006a 0x02000013 0x02010010 + 0x02020019 0x02030007 0x02040018 + 0x02050031 0x02060032 0x02070005 + 0x02080028 0x0209006c 0x03000026 + 0x03010025 0x03020024 0x0303000a + 0x03040017 0x03050023 0x03060022 + 0x03070008 0x03080035 0x03090069 + 0x04000021 0x04010012 0x04020020 + 0x0404002e 0x04050030 0x0406001e + 0x0407000d 0x04080037 0x04090067 + 0x05010038 0x0502000c 0x0503001b + 0x05040034 0x0505001a 0x05060006 + 0x05080027 0x0509000e 0x050a006f + 0x0600002b 0x0602004e 0x06030068 + 0x06040003 0x0605006d 0x06060009 + 0x06070001 0x0609000f 0x0708002a + 0x0709001d 0x070a0033 >; +}; diff --git a/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt new file mode 100644 index 000000000..a3dde8c30 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,palmas-pwrbutton.txt @@ -0,0 +1,36 @@ +Texas Instruments Palmas family power button module + +This module is part of the Palmas family of PMICs. For more details +about the whole chip see: +Documentation/devicetree/bindings/mfd/palmas.txt. + +This module provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be one of the following + - "ti,palmas-pwrbutton": For Palmas compatible power on button +- interrupt-parent: Parent interrupt device, must be handle of palmas node. +- interrupts: Interrupt number of power button submodule on device. + +Optional Properties: + +- ti,palmas-long-press-seconds: Duration in seconds which the power + button should be kept pressed for Palmas to power off automatically. + NOTE: This depends on OTP support and POWERHOLD signal configuration + on platform. Valid values are 6, 8, 10 and 12. +- ti,palmas-pwron-debounce-milli-seconds: Duration in milliseconds + which the power button should be kept pressed for Palmas to register + a press for debouncing purposes. NOTE: This depends on specific + Palmas variation capability. Valid values are 15, 100, 500 and 1000. + +Example: + +&palmas { + palmas_pwr_button: pwrbutton { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps659038>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + ti,palmas-long-press-seconds = <12>; + ti,palmas-pwron-debounce-milli-seconds = <15>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt new file mode 100644 index 000000000..f40f21c64 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/auo_pixcir_ts.txt @@ -0,0 +1,30 @@ +* AUO in-cell touchscreen controller using Pixcir sensors + +Required properties: +- compatible: must be "auo,auo_pixcir_ts" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- gpios: gpios the chip is connected to + first one is the interrupt gpio and second one the reset gpio +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Example: + + i2c@00000000 { + /* ... */ + + auo_pixcir_ts@5c { + compatible = "auo,auo_pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + + gpios = <&gpf 2 0 2>, /* INT */ + <&gpf 5 1 0>; /* RST */ + + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt new file mode 100644 index 000000000..34e3382a0 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/brcm,iproc-touchscreen.txt @@ -0,0 +1,76 @@ +* Broadcom's IPROC Touchscreen Controller + +Required properties: +- compatible: must be "brcm,iproc-touchscreen" +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: The clock provided by the SOC to driver the tsc +- clock-name: name for the clock +- interrupts: The touchscreen controller's interrupt + +Optional properties: +- scanning_period: Time between scans. Each step is 1024 us. Valid 1-256. +- debounce_timeout: Each step is 512 us. Valid 0-255 +- settling_timeout: The settling duration (in ms) is the amount of time + the tsc waits to allow the voltage to settle after + turning on the drivers in detection mode. + Valid values: 0-11 + 0 = 0.008 ms + 1 = 0.01 ms + 2 = 0.02 ms + 3 = 0.04 ms + 4 = 0.08 ms + 5 = 0.16 ms + 6 = 0.32 ms + 7 = 0.64 ms + 8 = 1.28 ms + 9 = 2.56 ms + 10 = 5.12 ms + 11 = 10.24 ms +- touch_timeout: The continuous number of scan periods in which touch is + not detected before the controller returns to idle state. + Valid values 0-255. +- average_data: Number of data samples which are averaged before a final + data point is placed into the FIFO + Valid values 0-7 + 0 = 1 sample + 1 = 2 samples + 2 = 4 samples + 3 = 8 samples + 4 = 16 samples + 5 = 32 samples + 6 = 64 samples + 7 = 128 samples +- fifo_threshold: Interrupt is generated whenever the number of fifo + entries exceeds this value + Valid values 0-31 +- touchscreen-size-x: horizontal resolution of touchscreen (in pixels) +- touchscreen-size-y: vertical resolution of touchscreen (in pixels) +- touchscreen-fuzz-x: horizontal noise value of the absolute input + device (in pixels) +- touchscreen-fuzz-y: vertical noise value of the absolute input + device (in pixels) +- touchscreen-inverted-x: X axis is inverted (boolean) +- touchscreen-inverted-y: Y axis is inverted (boolean) + +Example: + + touchscreen: tsc@0x180A6000 { + compatible = "brcm,iproc-touchscreen"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x180A6000 0x40>; + clocks = <&adc_clk>; + clock-names = "tsc_clk"; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + + scanning_period = <5>; + debounce_timeout = <40>; + settling_timeout = <7>; + touch_timeout = <10>; + average_data = <5>; + fifo_threshold = <1>; + /* Touchscreen is rotated 180 degrees. */ + touchscreen-inverted-x; + touchscreen-inverted-y; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt new file mode 100644 index 000000000..ca5a2c864 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/bu21013.txt @@ -0,0 +1,28 @@ +* Rohm BU21013 Touch Screen + +Required properties: + - compatible : "rohm,bu21013_tp" + - reg : I2C device address + +Optional properties: + - touch-gpio : GPIO pin registering a touch event + - <supply_name>-supply : Phandle to a regulator supply + - rohm,touch-max-x : Maximum outward permitted limit in the X axis + - rohm,touch-max-y : Maximum outward permitted limit in the Y axis + - rohm,flip-x : Flip touch coordinates on the X axis + - rohm,flip-y : Flip touch coordinates on the Y axis + +Example: + + i2c@80110000 { + bu21013_tp@0x5c { + compatible = "rohm,bu21013_tp"; + reg = <0x5c>; + touch-gpio = <&gpio2 20 0x4>; + avdd-supply = <&ab8500_ldo_aux1_reg>; + + rohm,touch-max-x = <384>; + rohm,touch-max-y = <704>; + rohm,flip-y; + }; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt b/Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt new file mode 100644 index 000000000..d11f8d615 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt @@ -0,0 +1,46 @@ +* ChipOne icn8318 I2C touchscreen controller + +Required properties: + - compatible : "chipone,icn8318" + - reg : I2C slave address of the chip (0x40) + - interrupt-parent : a phandle pointing to the interrupt controller + serving the interrupt for this chip + - interrupts : interrupt specification for the icn8318 interrupt + - wake-gpios : GPIO specification for the WAKE input + - touchscreen-size-x : horizontal resolution of touchscreen (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen (in pixels) + +Optional properties: + - pinctrl-names : should be "default" + - pinctrl-0: : a phandle pointing to the pin settings for the + control gpios + - touchscreen-fuzz-x : horizontal noise value of the absolute input + device (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input + device (in pixels) + - touchscreen-inverted-x : X axis is inverted (boolean) + - touchscreen-inverted-y : Y axis is inverted (boolean) + - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) + Swapping is done after inverting the axis + +Example: + +i2c@00000000 { + /* ... */ + + chipone_icn8318@40 { + compatible = "chipone,icn8318"; + reg = <0x40>; + interrupt-parent = <&pio>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */ + pinctrl-names = "default"; + pinctrl-0 = <&ts_wake_pin_p66>; + wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */ + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-inverted-x; + touchscreen-swapped-x-y; + }; + + /* ... */ +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt new file mode 100644 index 000000000..76db96704 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt @@ -0,0 +1,55 @@ +FocalTech EDT-FT5x06 Polytouch driver +===================================== + +There are 3 variants of the chip for various touch panel sizes +FT5206GE1 2.8" .. 3.8" +FT5306DE4 4.3" .. 7" +FT5406EE8 7" .. 8.9" + +The software interface is identical for all those chips, so that +currently there is no need for the driver to distinguish between the +different chips. Nevertheless distinct compatible strings are used so +that a distinction can be added if necessary without changing the DT +bindings. + + +Required properties: + - compatible: "edt,edt-ft5206" + or: "edt,edt-ft5306" + or: "edt,edt-ft5406" + + - reg: I2C slave address of the chip (0x38) + - interrupt-parent: a phandle pointing to the interrupt controller + serving the interrupt for this chip + - interrupts: interrupt specification for the touchdetect + interrupt + +Optional properties: + - reset-gpios: GPIO specification for the RESET input + - wake-gpios: GPIO specification for the WAKE input + + - pinctrl-names: should be "default" + - pinctrl-0: a phandle pointing to the pin settings for the + control gpios + + - threshold: allows setting the "click"-threshold in the range + from 20 to 80. + + - gain: allows setting the sensitivity in the range from 0 to + 31. Note that lower values indicate higher + sensitivity. + + - offset: allows setting the edge compensation in the range from + 0 to 31. + +Example: + polytouch: edt-ft5x06@38 { + compatible = "edt,edt-ft5406", "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&edt_ft5x06_pins>; + interrupt-parent = <&gpio2>; + interrupts = <5 0>; + reset-gpios = <&gpio2 6 1>; + wake-gpios = <&gpio4 9 0>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt new file mode 100644 index 000000000..49fa14ed1 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/egalax-ts.txt @@ -0,0 +1,19 @@ +* EETI eGalax Multiple Touch Controller + +Required properties: +- compatible: must be "eeti,egalax_ts" +- reg: i2c slave address +- interrupt-parent: the phandle for the interrupt controller +- interrupts: touch controller interrupt +- wakeup-gpios: the gpio pin to be used for waking up the controller + and also used as irq pin + +Example: + + egalax_ts@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <9 2>; + wakeup-gpios = <&gpio1 9 0>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt new file mode 100644 index 000000000..8ba98eec7 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt @@ -0,0 +1,29 @@ +Device tree bindings for Goodix GT9xx series touchscreen controller + +Required properties: + + - compatible : Should be "goodix,gt911" + or "goodix,gt9110" + or "goodix,gt912" + or "goodix,gt927" + or "goodix,gt9271" + or "goodix,gt928" + or "goodix,gt967" + - reg : I2C address of the chip. Should be 0x5d or 0x14 + - interrupt-parent : Interrupt controller to which the chip is connected + - interrupts : Interrupt to which the chip is connected + +Example: + + i2c@00000000 { + /* ... */ + + gt928@5d { + compatible = "goodix,gt928"; + reg = <0x5d>; + interrupt-parent = <&gpio>; + interrupts = <0 0>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt new file mode 100644 index 000000000..41cbf4b7a --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/lpc32xx-tsc.txt @@ -0,0 +1,16 @@ +* NXP LPC32xx SoC Touchscreen Controller (TSC) + +Required properties: +- compatible: must be "nxp,lpc3220-tsc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The TSC/ADC interrupt + +Example: + + tsc@40048000 { + compatible = "nxp,lpc3220-tsc"; + reg = <0x40048000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <39 0>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/mms114.txt b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt new file mode 100644 index 000000000..89d4c56c5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/mms114.txt @@ -0,0 +1,34 @@ +* MELFAS MMS114 touchscreen controller + +Required properties: +- compatible: must be "melfas,mms114" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Optional properties: +- contact-threshold: +- moving-threshold: +- x-invert: invert X axis +- y-invert: invert Y axis + +Example: + + i2c@00000000 { + /* ... */ + + touchscreen@48 { + compatible = "melfas,mms114"; + reg = <0x48>; + interrupts = <39 0>; + x-size = <720>; + y-size = <1280>; + contact-threshold = <10>; + moving-threshold = <10>; + x-invert; + y-invert; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt new file mode 100644 index 000000000..6e551090f --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt @@ -0,0 +1,26 @@ +* Pixcir I2C touchscreen controllers + +Required properties: +- compatible: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- attb-gpio: GPIO connected to the ATTB line of the chip +- touchscreen-size-x: horizontal resolution of touchscreen (in pixels) +- touchscreen-size-y: vertical resolution of touchscreen (in pixels) + +Example: + + i2c@00000000 { + /* ... */ + + pixcir_ts@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + attb-gpio = <&gpf 2 0 2>; + touchscreen-size-x = <800>; + touchscreen-size-y = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt new file mode 100644 index 000000000..64ad48b82 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt @@ -0,0 +1,24 @@ +* Sitronix st1232 touchscreen controller + +Required properties: +- compatible: must be "sitronix,st1232" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected + +Optional properties: +- gpios: a phandle to the reset GPIO + +Example: + + i2c@00000000 { + /* ... */ + + touchscreen@55 { + compatible = "sitronix,st1232"; + reg = <0x55>; + interrupts = <2 0>; + gpios = <&gpio1 166 0>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt new file mode 100644 index 000000000..127baa31a --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -0,0 +1,43 @@ +STMPE Touchscreen +---------------- + +Required properties: + - compatible: "st,stmpe-ts" + +Optional properties: +- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> + 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 + -> 144 clocks), recommended is 4. +- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) +- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external + reference) +- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) +- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 + samples, 3 -> 8 samples) +- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> + 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended + is 3 +- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 + -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 +- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of + the fractional part) recommended is 7 +- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 + mA max, 1 -> 50 mA typical 80 mA max) + +Node name must be stmpe_touchscreen and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + st,sample-time = <4>; + st,mod-12b = <1>; + st,ref-sel = <0>; + st,adc-freq = <1>; + st,ave-ctrl = <1>; + st,touch-det-delay = <2>; + st,settling = <2>; + st,fraction-z = <7>; + st,i-drive = <1>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt new file mode 100644 index 000000000..89abecd93 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sun4i.txt @@ -0,0 +1,38 @@ +sun4i resistive touchscreen controller +-------------------------------------- + +Required properties: + - compatible: "allwinner,sun4i-a10-ts", "allwinner,sun5i-a13-ts" or + "allwinner,sun6i-a31-ts" + - reg: mmio address range of the chip + - interrupts: interrupt to which the chip is connected + - #thermal-sensor-cells: shall be 0 + +Optional properties: + - allwinner,ts-attached : boolean indicating that an actual touchscreen + is attached to the controller + - allwinner,tp-sensitive-adjust : integer (4 bits) + adjust sensitivity of pen down detection + between 0 (least sensitive) and 15 + (defaults to 15) + - allwinner,filter-type : integer (2 bits) + select median and averaging filter + samples used for median / averaging filter + 0: 4/2 + 1: 5/3 + 2: 8/4 + 3: 16/8 + (defaults to 1) + +Example: + + rtp: rtp@01c25000 { + compatible = "allwinner,sun4i-a10-ts"; + reg = <0x01c25000 0x100>; + interrupts = <29>; + allwinner,ts-attached; + #thermal-sensor-cells = <0>; + /* sensitive/noisy touch panel */ + allwinner,tp-sensitive-adjust = <0>; + allwinner,filter-type = <3>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt new file mode 100644 index 000000000..5aaa6b3aa --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt @@ -0,0 +1,16 @@ +* Semtech SX8654 I2C Touchscreen Controller + +Required properties: +- compatible: must be "semtech,sx8654" +- reg: i2c slave address +- interrupt-parent: the phandle for the interrupt controller +- interrupts: touch controller interrupt + +Example: + + sx8654@48 { + compatible = "semtech,sx8654"; + reg = <0x48>; + interrupt-parent = <&gpio6>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt new file mode 100644 index 000000000..6c4fb3482 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt @@ -0,0 +1,59 @@ +* TI - TSC ADC (Touschscreen and analog digital converter) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Required properties: +- child "tsc" + ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen + support on the platform. + ti,x-plate-resistance: X plate resistance + ti,coordinate-readouts: The sequencer supports a total of 16 + programmable steps each step is used to + read a single coordinate. A single + readout is enough but multiple reads can + increase the quality. + A value of 5 means, 5 reads for X, 5 for + Y and 2 for Z (always). This utilises 12 + of the 16 software steps available. The + remaining 4 can be used by the ADC. + ti,wire-config: Different boards could have a different order for + connecting wires on touchscreen. We need to provide an + 8 bit number where in the 1st four bits represent the + analog lines and the next 4 bits represent positive/ + negative terminal on that input line. Notations to + represent the input lines and terminals resoectively + is as follows: + AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. + XP = 0, XN = 1, YP = 2, YN = 3. +- child "adc" + ti,adc-channels: List of analog inputs available for ADC. + AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. + +Optional properties: +- child "tsc" + ti,charge-delay: Length of touch screen charge delay step in terms of + ADC clock cycles. Charge delay value should be large + in order to avoid false pen-up events. This value + effects the overall sampling speed, hence need to be + kept as low as possible, while avoiding false pen-up + event. Start from a lower value, say 0x400, and + increase value until false pen-up events are avoided. + The pen-up detection happens immediately after the + charge step, so this does in fact function as a + hardware knob for adjusting the amount of "settling + time". + +Example: + tscadc: tscadc@44e0d000 { + compatible = "ti,am3359-tscadc"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordiante-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + ti,charge-delay = <0x400>; + }; + + adc { + ti,adc-channels = <4 5 6 7>; + }; + } diff --git a/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt new file mode 100644 index 000000000..ac23caf51 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt @@ -0,0 +1,29 @@ +General Touchscreen Properties: + +Optional properties for Touchscreens: + - touchscreen-size-x : horizontal resolution of touchscreen + (in pixels) + - touchscreen-size-y : vertical resolution of touchscreen + (in pixels) + - touchscreen-max-pressure : maximum reported pressure (arbitrary range + dependent on the controller) + - touchscreen-fuzz-x : horizontal noise value of the absolute input + device (in pixels) + - touchscreen-fuzz-y : vertical noise value of the absolute input + device (in pixels) + - touchscreen-fuzz-pressure : pressure noise value of the absolute input + device (arbitrary range dependent on the + controller) + - touchscreen-inverted-x : X axis is inverted (boolean) + - touchscreen-inverted-y : Y axis is inverted (boolean) + - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) + Swapping is done after inverting the axis + +Deprecated properties for Touchscreens: + - x-size : deprecated name for touchscreen-size-x + - y-size : deprecated name for touchscreen-size-y + - moving-threshold : deprecated name for a combination of + touchscreen-fuzz-x and touchscreen-fuzz-y + - contact-threshold : deprecated name for touchscreen-fuzz-pressure + - x-invert : deprecated name for touchscreen-inverted-x + - y-invert : deprecated name for touchscreen-inverted-y diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt new file mode 100644 index 000000000..09089a6d6 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt @@ -0,0 +1,42 @@ +* Texas Instruments tsc2005 touchscreen controller + +Required properties: + - compatible : "ti,tsc2005" + - reg : SPI device address + - spi-max-frequency : Maximal SPI speed + - interrupts : IRQ specifier + - reset-gpios : GPIO specifier + - vio-supply : Regulator specifier + +Optional properties: + - ti,x-plate-ohms : integer, resistance of the touchscreen's X plates + in ohm (defaults to 280) + - ti,esd-recovery-timeout-ms : integer, if the touchscreen does not respond after + the configured time (in milli seconds), the driver + will reset it. This is disabled by default. + - properties defined in touchscreen.txt + +Example: + +&mcspi1 { + tsc2005@0 { + compatible = "ti,tsc2005"; + spi-max-frequency = <6000000>; + reg = <0>; + + vio-supply = <&vio>; + + reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */ + interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */ + + touchscreen-fuzz-x = <4>; + touchscreen-fuzz-y = <7>; + touchscreen-fuzz-pressure = <2>; + touchscreen-size-x = <4096>; + touchscreen-size-y = <4096>; + touchscreen-max-pressure = <2048>; + + ti,x-plate-ohms = <280>; + ti,esd-recovery-timeout-ms = <8000>; + }; +} diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt new file mode 100644 index 000000000..ec365e172 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt @@ -0,0 +1,41 @@ +* Texas Instruments tsc2007 touchscreen controller + +Required properties: +- compatible: must be "ti,tsc2007". +- reg: I2C address of the chip. +- ti,x-plate-ohms: X-plate resistance in ohms. + +Optional properties: +- gpios: the interrupt gpio the chip is connected to (trough the penirq pin). + The penirq pin goes to low when the panel is touched. + (see GPIO binding[1] for more details). +- interrupt-parent: the phandle for the gpio controller + (see interrupt binding[0]). +- interrupts: (gpio) interrupt to which the chip is connected + (see interrupt binding[0]). +- ti,max-rt: maximum pressure. +- ti,fuzzx: specifies the absolute input fuzz x value. + If set, it will permit noise in the data up to +- the value given to the fuzz + parameter, that is used to filter noise from the event stream. +- ti,fuzzy: specifies the absolute input fuzz y value. +- ti,fuzzz: specifies the absolute input fuzz z value. +- ti,poll-period: how much time to wait (in milliseconds) before reading again the + values from the tsc2007. + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + &i2c1 { + /* ... */ + tsc2007@49 { + compatible = "ti,tsc2007"; + reg = <0x49>; + interrupt-parent = <&gpio4>; + interrupts = <0x0 0x8>; + gpios = <&gpio4 0 0>; + ti,x-plate-ohms = <180>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt new file mode 100644 index 000000000..80c37df94 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt @@ -0,0 +1,34 @@ +* Neonode infrared touchscreen controller + +Required properties: +- compatible: must be "neonode,zforce" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- gpios: gpios the chip is connected to + first one is the interrupt gpio and second one the reset gpio +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Optional properties: +- vdd-supply: Regulator controlling the controller supply + +Example: + + i2c@00000000 { + /* ... */ + + zforce_ts@50 { + compatible = "neonode,zforce"; + reg = <0x50>; + interrupts = <2 0>; + vdd-supply = <®_zforce_vdd>; + + gpios = <&gpio5 6 0>, /* INT */ + <&gpio5 9 0>; /* RST */ + + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt new file mode 100644 index 000000000..e30e0b93f --- /dev/null +++ b/Documentation/devicetree/bindings/input/tps65218-pwrbutton.txt @@ -0,0 +1,17 @@ +Texas Instruments TPS65218 power button + +This driver provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be "ti,tps65218-pwrbutton" +- interrupts: should be one of the following + - <3 IRQ_TYPE_EDGE_BOTH>: For controllers compatible with tps65218 + +Example: + +&tps { + power-button { + compatible = "ti,tps65218-pwrbutton"; + interrupts = <3 IRQ_TYPE_EDGE_BOTH>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/twl4030-keypad.txt b/Documentation/devicetree/bindings/input/twl4030-keypad.txt new file mode 100644 index 000000000..e4be2f76a --- /dev/null +++ b/Documentation/devicetree/bindings/input/twl4030-keypad.txt @@ -0,0 +1,27 @@ +* TWL4030's Keypad Controller device tree bindings + +TWL4030's Keypad controller is used to interface a SoC with a matrix-type +keypad device. The keypad controller supports multiple row and column lines. +A key can be placed at each intersection of a unique row and a unique column. +The keypad controller can sense a key-press and key-release and report the +event using a interrupt to the cpu. + +This binding is based on the matrix-keymap binding with the following +changes: + + * keypad,num-rows and keypad,num-columns are required. + +Required SoC Specific Properties: +- compatible: should be one of the following + - "ti,twl4030-keypad": For controllers compatible with twl4030 keypad + controller. +- interrupt: should be one of the following + - <1>: For controllers compatible with twl4030 keypad controller. + +Example: + twl_keypad: keypad { + compatible = "ti,twl4030-keypad"; + interrupts = <1>; + keypad,num-rows = <8>; + keypad,num-columns = <8>; + }; diff --git a/Documentation/devicetree/bindings/input/twl4030-pwrbutton.txt b/Documentation/devicetree/bindings/input/twl4030-pwrbutton.txt new file mode 100644 index 000000000..c864a46cd --- /dev/null +++ b/Documentation/devicetree/bindings/input/twl4030-pwrbutton.txt @@ -0,0 +1,21 @@ +Texas Instruments TWL family (twl4030) pwrbutton module + +This module is part of the TWL4030. For more details about the whole +chip see Documentation/devicetree/bindings/mfd/twl-familly.txt. + +This module provides a simple power button event via an Interrupt. + +Required properties: +- compatible: should be one of the following + - "ti,twl4030-pwrbutton": For controllers compatible with twl4030 +- interrupts: should be one of the following + - <8>: For controllers compatible with twl4030 + +Example: + +&twl { + twl_pwrbutton: pwrbutton { + compatible = "ti,twl4030-pwrbutton"; + interrupts = <8>; + }; +}; |