diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iommu')
3 files changed, 91 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt new file mode 100644 index 000000000..cd1b1cd7b --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt @@ -0,0 +1,68 @@ +* Mediatek IOMMU Architecture Implementation + + Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U) which +uses the ARM Short-Descriptor translation table format for address translation. + + About the M4U Hardware Block Diagram, please check below: + + EMI (External Memory Interface) + | + m4u (Multimedia Memory Management Unit) + | + SMI Common(Smart Multimedia Interface Common) + | + +----------------+------- + | | + | | + SMI larb0 SMI larb1 ... SoCs have several SMI local arbiter(larb). + (display) (vdec) + | | + | | + +-----+-----+ +----+----+ + | | | | | | + | | |... | | | ... There are different ports in each larb. + | | | | | | +OVL0 RDMA0 WDMA0 MC PP VLD + + As above, The Multimedia HW will go through SMI and M4U while it +access EMI. SMI is a bridge between m4u and the Multimedia HW. It contain +smi local arbiter and smi common. It will control whether the Multimedia +HW should go though the m4u for translation or bypass it and talk +directly with EMI. And also SMI help control the power domain and clocks for +each local arbiter. + Normally we specify a local arbiter(larb) for each multimedia HW +like display, video decode, and camera. And there are different ports +in each larb. Take a example, There are many ports like MC, PP, VLD in the +video decode local arbiter, all these ports are according to the video HW. + +Required properties: +- compatible : must be "mediatek,mt8173-m4u". +- reg : m4u register base and size. +- interrupts : the interrupt of m4u. +- clocks : must contain one entry for each clock-names. +- clock-names : must be "bclk", It is the block clock of m4u. +- mediatek,larbs : List of phandle to the local arbiters in the current Socs. + Refer to bindings/memory-controllers/mediatek,smi-larb.txt. It must sort + according to the local arbiter index, like larb0, larb1, larb2... +- iommu-cells : must be 1. This is the mtk_m4u_id according to the HW. + Specifies the mtk_m4u_id as defined in + dt-binding/memory/mt8173-larb-port.h. + +Example: + iommu: iommu@10205000 { + compatible = "mediatek,mt8173-m4u"; + reg = <0 0x10205000 0 0x1000>; + interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_INFRA_M4U>; + clock-names = "bclk"; + mediatek,larbs = <&larb0 &larb1 &larb2 &larb3 &larb4 &larb5>; + #iommu-cells = <1>; + }; + +Example for a client device: + display { + compatible = "mediatek,mt8173-disp"; + iommus = <&iommu M4U_PORT_DISP_OVL0>, + <&iommu M4U_PORT_DISP_RDMA0>; + ... + }; diff --git a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt index 48ffb38f6..3ed027cfc 100644 --- a/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt +++ b/Documentation/devicetree/bindings/iommu/renesas,ipmmu-vmsa.txt @@ -7,23 +7,34 @@ connected to the IPMMU through a port called micro-TLB. Required Properties: - - compatible: Must contain SoC-specific and generic entries from below. + - compatible: Must contain SoC-specific and generic entry below in case + the device is compatible with the R-Car Gen2 VMSA-compatible IPMMU. - "renesas,ipmmu-r8a73a4" for the R8A73A4 (R-Mobile APE6) IPMMU. - "renesas,ipmmu-r8a7790" for the R8A7790 (R-Car H2) IPMMU. - "renesas,ipmmu-r8a7791" for the R8A7791 (R-Car M2-W) IPMMU. - "renesas,ipmmu-r8a7793" for the R8A7793 (R-Car M2-N) IPMMU. - "renesas,ipmmu-r8a7794" for the R8A7794 (R-Car E2) IPMMU. + - "renesas,ipmmu-r8a7795" for the R8A7795 (R-Car H3) IPMMU. - "renesas,ipmmu-vmsa" for generic R-Car Gen2 VMSA-compatible IPMMU. - reg: Base address and size of the IPMMU registers. - interrupts: Specifiers for the MMU fault interrupts. For instances that support secure mode two interrupts must be specified, for non-secure and secure mode, in that order. For instances that don't support secure mode a - single interrupt must be specified. + single interrupt must be specified. Not required for cache IPMMUs. - #iommu-cells: Must be 1. +Optional properties: + + - renesas,ipmmu-main: reference to the main IPMMU instance in two cells. + The first cell is a phandle to the main IPMMU and the second cell is + the interrupt bit number associated with the particular cache IPMMU device. + The interrupt bit number needs to match the main IPMMU IMSSTR register. + Only used by cache IPMMU instances. + + Each bus master connected to an IPMMU must reference the IPMMU in its device node with the following property: diff --git a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt index bc620fe32..85f068805 100644 --- a/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt +++ b/Documentation/devicetree/bindings/iommu/samsung,sysmmu.txt @@ -23,28 +23,24 @@ MMUs. for window 1, 2 and 3. * M2M Scalers and G2D in Exynos5420 has one System MMU on the read channel and the other System MMU on the write channel. -The drivers must consider how to handle those System MMUs. One of the idea is -to implement child devices or sub-devices which are the client devices of the -System MMU. -Note: -The current DT binding for the Exynos System MMU is incomplete. -The following properties can be removed or changed, if found incompatible with -the "Generic IOMMU Binding" support for attaching devices to the IOMMU. +For information on assigning System MMU controller to its peripheral devices, +see generic IOMMU bindings. Required properties: - compatible: Should be "samsung,exynos-sysmmu" - reg: A tuple of base address and size of System MMU registers. +- #iommu-cells: Should be <0>. - interrupt-parent: The phandle of the interrupt controller of System MMU - interrupts: An interrupt specifier for interrupt signal of System MMU, according to the format defined by a particular interrupt controller. -- clock-names: Should be "sysmmu" if the System MMU is needed to gate its clock. +- clock-names: Should be "sysmmu" or a pair of "aclk" and "pclk" to gate + SYSMMU core clocks. Optional "master" if the clock to the System MMU is gated by - another gate clock other than "sysmmu". - Exynos4 SoCs, there needs no "master" clock. - Exynos5 SoCs, some System MMUs must have "master" clocks. -- clocks: Required if the System MMU is needed to gate its clock. + another gate clock other core (usually main gate clock + of peripheral device this SYSMMU belongs to). +- clocks: Phandles for respective clocks described by clock-names. - power-domains: Required if the System MMU is needed to gate its power. Please refer to the following document: Documentation/devicetree/bindings/power/pd-samsung.txt @@ -57,6 +53,7 @@ Examples: power-domains = <&pd_gsc>; clocks = <&clock CLK_GSCL0>; clock-names = "gscl"; + iommus = <&sysmmu_gsc0>; }; sysmmu_gsc0: sysmmu@13E80000 { @@ -67,4 +64,5 @@ Examples: clock-names = "sysmmu", "master"; clocks = <&clock CLK_SMMU_GSCL0>, <&clock CLK_GSCL0>; power-domains = <&pd_gsc>; + #iommu-cells = <0>; }; |