diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd/s2mps11.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/s2mps11.txt | 139 |
1 files changed, 139 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt new file mode 100644 index 000000000..57a045016 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -0,0 +1,139 @@ + +* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator + +The Samsung S2MPS11 is a multi-function device which includes voltage and +current regulators, RTC, charger controller and other sub-blocks. It is +interfaced to the host controller using an I2C interface. Each sub-block is +addressed by the host system using different I2C slave addresses. + +Required properties: +- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic" + or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic". +- reg: Specifies the I2C slave address of the pmic block. It should be 0x66. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s2mps11 are delivered to. +- interrupts: Interrupt specifiers for interrupt sources. + +Optional nodes: +- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 + KHz outputs, so to register these as clocks with common clock framework + instantiate a sub-node named "clocks". It uses the common clock binding + documented in : + [Documentation/devicetree/bindings/clock/clock-bindings.txt] + The s2mps14 provides two (AP/BT) buffered 32.768 KHz outputs. + - #clock-cells: should be 1. + + - The following is the list of clocks generated by the controller. Each clock + is assigned an identifier and client nodes use this identifier to specify + the clock which they consume. + Clock ID Devices + ---------------------------------------------------------- + 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767 + 32KhzCP 1 S2MPS11, S2MPS13, S5M8767 + 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767 + + - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", + "samsung,s2mps14-clk", "samsung,s5m8767-clk" + +- regulators: The regulators of s2mps11 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + [standard regulator constraints....]; + }; + + regulator-ramp-delay for BUCKs = [6250/12500/25000(default)/50000] uV/us + + BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explicitly + regulator-ramp-delay = <0> can be used for them to disable ramp delay. + In the absence of the regulator-ramp-delay property, the default ramp + delay will be used. + +NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set +for a particular group of BUCKs. So provide same regulator-ramp-delay<value>. +Grouping of BUCKs sharing ramp rate setting is as follow : BUCK[1, 6], +BUCK[3, 4], and BUCK[7, 8, 10] + +On S2MPS14 the LDO10, LDO11 and LDO12 can be configured to external control +over GPIO. To turn this feature on this property must be added to the regulator +sub-node: + - samsung,ext-control-gpios: GPIO specifier for one GPIO + controlling this regulator (enable/disable); +Example: + LDO12 { + regulator-name = "V_EMMC_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + +The regulator constraints inside the regulator nodes use the standard regulator +bindings which are documented elsewhere. + +The following are the names of the regulators that the s2mps11 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of s2mps11. + + - LDOn + - valid values for n are: + - S2MPS11: 1 to 38 + - S2MPS13: 1 to 40 + - S2MPS14: 1 to 25 + - S2MPU02: 1 to 28 + - Example: LDO1, LDO2, LDO28 + - BUCKn + - valid values for n are: + - S2MPS11: 1 to 10 + - S2MPS13: 1 to 10 + - S2MPS14: 1 to 5 + - S2MPU02: 1 to 7 + - Example: BUCK1, BUCK2, BUCK9 + +Example: + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + + s2m_osc: clocks { + compatible = "samsung,s2mps11-clk"; + #clock-cells = <1>; + clock-output-names = "xx", "yy", "zz"; + }; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <50000>; + }; + }; + }; |