diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd')
50 files changed, 3927 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/88pm860x.txt b/Documentation/devicetree/bindings/mfd/88pm860x.txt new file mode 100644 index 000000000..63f3ee337 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/88pm860x.txt @@ -0,0 +1,85 @@ +* Marvell 88PM860x Power Management IC + +Required parent device properties: +- compatible : "marvell,88pm860x" +- reg : the I2C slave address for the 88pm860x chip +- interrupts : IRQ line for the 88pm860x chip +- interrupt-controller: describes the 88pm860x as an interrupt controller (has its own domain) +- #interrupt-cells : should be 1. + - The cell is the 88pm860x local IRQ number + +Optional parent device properties: +- marvell,88pm860x-irq-read-clr: inicates whether interrupt status is cleared by read +- marvell,88pm860x-slave-addr: 88pm860x are two chips solution. <reg> stores the I2C address + of one chip, and this property stores the I2C address of + another chip. + +88pm860x consists of a large and varied group of sub-devices: + +Device Supply Names Description +------ ------------ ----------- +88pm860x-onkey : : On key +88pm860x-rtc : : RTC +88pm8607 : : Regulators +88pm860x-backlight : : Backlight +88pm860x-led : : Led +88pm860x-touch : : Touchscreen + +Example: + + pmic: 88pm860x@34 { + compatible = "marvell,88pm860x"; + reg = <0x34>; + interrupts = <4>; + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <1>; + + marvell,88pm860x-irq-read-clr; + marvell,88pm860x-slave-addr = <0x11>; + + regulators { + BUCK1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + LDO1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + rtc { + marvell,88pm860x-vrtc = <1>; + }; + touch { + marvell,88pm860x-gpadc-prebias = <1>; + marvell,88pm860x-gpadc-slot-cycle = <1>; + marvell,88pm860x-tsi-prebias = <6>; + marvell,88pm860x-pen-prebias = <16>; + marvell,88pm860x-pen-prechg = <2>; + marvell,88pm860x-resistor-X = <300>; + }; + backlights { + backlight-0 { + marvell,88pm860x-iset = <4>; + marvell,88pm860x-pwm = <3>; + }; + backlight-2 { + }; + }; + leds { + led0-red { + marvell,88pm860x-iset = <12>; + }; + led0-green { + marvell,88pm860x-iset = <12>; + }; + led0-blue { + marvell,88pm860x-iset = <12>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt new file mode 100644 index 000000000..cd9e90c5d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -0,0 +1,159 @@ +* AB8500 Multi-Functional Device (MFD) + +Required parent device properties: +- compatible : contains "stericsson,ab8500"; +- interrupts : contains the IRQ line for the AB8500 +- interrupt-controller : describes the AB8500 as an Interrupt Controller (has its own domain) +- #interrupt-cells : should be 2, for 2-cell format + - The first cell is the AB8500 local IRQ number + - The second cell is used to specify optional parameters + - bits[3:0] trigger type and level flags: + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + +The AB8500 consists of a large and varied group of sub-devices: + +Device IRQ Names Supply Names Description +------ --------- ------------ ----------- +ab8500-bm : : : Battery Manager +ab8500-btemp : : : Battery Temperature +ab8500-charger : : : Battery Charger +ab8500-codec : : : Audio Codec +ab8500-fg : : vddadc : Fuel Gauge + : NCONV_ACCU : : Accumulate N Sample Conversion + : BATT_OVV : : Battery Over Voltage + : LOW_BAT_F : : LOW threshold battery voltage + : CC_INT_CALIB : : Coulomb Counter Internal Calibration + : CCEOC : : Coulomb Counter End of Conversion +ab8500-btemp : : vtvout : Battery Temperature + : BAT_CTRL_INDB : : Battery Removal Indicator + : BTEMP_LOW : : Btemp < BtempLow, if battery temperature is lower than -10°C + : BTEMP_LOW_MEDIUM : : BtempLow < Btemp < BtempMedium,if battery temperature is between -10 and 0°C + : BTEMP_MEDIUM_HIGH : : BtempMedium < Btemp < BtempHigh,if battery temperature is between 0°C and“MaxTemp + : BTEMP_HIGH : : Btemp > BtempHigh, if battery temperature is higher than “MaxTemp +ab8500-charger : : vddadc : Charger interface + : MAIN_CH_UNPLUG_DET : : main charger unplug detection management (not in 8505) + : MAIN_CHARGE_PLUG_DET : : main charger plug detection management (not in 8505) + : MAIN_EXT_CH_NOT_OK : : main charger not OK + : MAIN_CH_TH_PROT_R : : Die temp is above main charger + : MAIN_CH_TH_PROT_F : : Die temp is below main charger + : VBUS_DET_F : : VBUS falling detected + : VBUS_DET_R : : VBUS rising detected + : USB_LINK_STATUS : : USB link status has changed + : USB_CH_TH_PROT_R : : Die temp is above usb charger + : USB_CH_TH_PROT_F : : Die temp is below usb charger + : USB_CHARGER_NOT_OKR : : allowed USB charger not ok detection + : VBUS_OVV : : Overvoltage on Vbus ball detected (USB charge is stopped) + : CH_WD_EXP : : Charger watchdog detected +ab8500-gpadc : HW_CONV_END : vddadc : Analogue to Digital Converter + SW_CONV_END : : +ab8500-gpio : : : GPIO Controller +ab8500-ponkey : ONKEY_DBF : : Power-on Key + ONKEY_DBR : : +ab8500-pwm : : : Pulse Width Modulator +ab8500-regulator : : : Regulators +ab8500-rtc : 60S : : Real Time Clock + : ALARM : : +ab8500-sysctrl : : : System Control +ab8500-usb : ID_WAKEUP_R : vddulpivio18 : Universal Serial Bus + : ID_WAKEUP_F : v-ape : + : VBUS_DET_F : musb_1v8 : + : VBUS_DET_R : : + : USB_LINK_STATUS : : + : USB_ADP_PROBE_PLUG : : + : USB_ADP_PROBE_UNPLUG : : + +Required child device properties: +- compatible : "stericsson,ab8500-[bm|btemp|charger|fg|gpadc|gpio|ponkey| + pwm|regulator|rtc|sysctrl|usb]"; + +Optional child device properties: +- interrupts : contains the device IRQ(s) using the 2-cell format (see above) +- interrupt-names : contains names of IRQ resource in the order in which they were + supplied in the interrupts property +- <supply_name>-supply : contains a phandle to the regulator supply node in Device Tree + +Non-standard child device properties: + - Audio CODEC: + - stericsson,amic[1|2]-type-single-ended : Single-ended Analoge Mic (default: differential) + - stericsson,amic1a-bias-vamic2 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,amic1b-bias-vamic2 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,amic2-bias-vamic1 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,earpeice-cmv : Earpeice voltage (only: 950 | 1100 | 1270 | 1580) + +ab8500 { + compatible = "stericsson,ab8500"; + interrupts = <0 40 0x4>; + interrupt-controller; + #interrupt-cells = <2>; + + ab8500-rtc { + compatible = "stericsson,ab8500-rtc"; + interrupts = <17 0x4 + 18 0x4>; + interrupt-names = "60S", "ALARM"; + }; + + ab8500-gpadc { + compatible = "stericsson,ab8500-gpadc"; + interrupts = <32 0x4 + 39 0x4>; + interrupt-names = "HW_CONV_END", "SW_CONV_END"; + vddadc-supply = <&ab8500_ldo_tvout_reg>; + }; + + ab8500-usb { + compatible = "stericsson,ab8500-usb"; + interrupts = < 90 0x4 + 96 0x4 + 14 0x4 + 15 0x4 + 79 0x4 + 74 0x4 + 75 0x4>; + interrupt-names = "ID_WAKEUP_R", + "ID_WAKEUP_F", + "VBUS_DET_F", + "VBUS_DET_R", + "USB_LINK_STATUS", + "USB_ADP_PROBE_PLUG", + "USB_ADP_PROBE_UNPLUG"; + vddulpivio18-supply = <&ab8500_ldo_intcore_reg>; + v-ape-supply = <&db8500_vape_reg>; + musb_1v8-supply = <&db8500_vsmps2_reg>; + }; + + ab8500-ponkey { + compatible = "stericsson,ab8500-ponkey"; + interrupts = <6 0x4 + 7 0x4>; + interrupt-names = "ONKEY_DBF", "ONKEY_DBR"; + }; + + ab8500-sysctrl { + compatible = "stericsson,ab8500-sysctrl"; + }; + + ab8500-pwm { + compatible = "stericsson,ab8500-pwm"; + }; + + codec: ab8500-codec { + compatible = "stericsson,ab8500-codec"; + + stericsson,earpeice-cmv = <950>; /* Units in mV. */ + }; + + ab8500-regulators { + compatible = "stericsson,ab8500-regulator"; + + ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { + /* + * See: Documentation/devicetree/bindings/regulator/regulator.txt + * for more information on regulators + */ + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt new file mode 100644 index 000000000..7665aa959 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -0,0 +1,95 @@ +Wolfson Arizona class audio SoCs + +These devices are audio SoCs with extensive digital capabilites and a range +of analogue I/O. + +Required properties: + + - compatible : One of the following chip-specific strings: + "wlf,wm5102" + "wlf,wm5110" + "wlf,wm8280" + "wlf,wm8997" + - reg : I2C slave address when connected using I2C, chip select number when + using SPI. + + - interrupts : The interrupt line the /IRQ signal for the device is + connected to. + - interrupt-controller : Arizona class devices contain interrupt controllers + and may provide interrupt services to other devices. + - interrupt-parent : The parent interrupt controller. + - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt + + - gpio-controller : Indicates this device is a GPIO controller. + - #gpio-cells : Must be 2. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + + - AVDD-supply, DBVDD1-supply, CPVDD-supply : Power supplies for the device, + as covered in Documentation/devicetree/bindings/regulator/regulator.txt + + - DBVDD2-supply, DBVDD3-supply : Additional databus power supplies (wm5102, + wm5110, wm8280) + + - SPKVDDL-supply, SPKVDDR-supply : Speaker driver power supplies (wm5102, + wm5110, wm8280) + + - SPKVDD-supply : Speaker driver power supply (wm8997) + +Optional properties: + + - wlf,reset : GPIO specifier for the GPIO controlling /RESET + - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA + + - wlf,gpio-defaults : A list of GPIO configuration register values. Defines + for the appropriate values can found in <dt-bindings/mfd/arizona.txt>. If + absent, no configuration of these registers is performed. If any entry has + a value that is out of range for a 16 bit register then the chip default + will be used. If present exactly five values must be specified. + + - wlf,inmode : A list of INn_MODE register values, where n is the number + of input signals. Valid values are 0 (Differential), 1 (Single-ended) and + 2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default. + If present, values must be specified less than or equal to the number of + input singals. If values less than the number of input signals, elements + that has not been specifed are set to 0 by default. + + - wlf,dmic-ref : DMIC reference voltage source for each input, can be + selected from either MICVDD or one of the MICBIAS's, defines + (ARIZONA_DMIC_xxxx) are provided in <dt-bindings/mfd/arizona.txt>. If + present, the number of values should be less than or equal to the + number of inputs, unspecified inputs will use the chip default. + + - DCVDD-supply, MICVDD-supply : Power supplies, only need to be specified if + they are being externally supplied. As covered in + Documentation/devicetree/bindings/regulator/regulator.txt + +Optional subnodes: + - ldo1 : Initial data for the LDO1 regulator, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt + - micvdd : Initial data for the MICVDD regulator, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt + +Example: + +codec: wm5102@1a { + compatible = "wlf,wm5102"; + reg = <0x1a>; + interrupts = <347>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + + gpio-controller; + #gpio-cells = <2>; + + wlf,gpio-defaults = < + ARIZONA_GP_FN_TXLRCLK + ARIZONA_GP_DEFAULT + ARIZONA_GP_DEFAULT + ARIZONA_GP_DEFAULT + ARIZONA_GP_DEFAULT + >; +}; diff --git a/Documentation/devicetree/bindings/mfd/as3711.txt b/Documentation/devicetree/bindings/mfd/as3711.txt new file mode 100644 index 000000000..d98cf18c7 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/as3711.txt @@ -0,0 +1,73 @@ +AS3711 is an I2C PMIC from Austria MicroSystems with multiple DCDC and LDO power +supplies, a battery charger and an RTC. So far only bindings for the two stepup +DCDC converters are defined. Other DCDC and LDO supplies are configured, using +standard regulator properties, they must belong to a sub-node, called +"regulators" and be called "sd1" to "sd4" and "ldo1" to "ldo8." Stepup converter +configuration should be placed in a subnode, called "backlight." + +Compulsory properties: +- compatible : must be "ams,as3711" +- reg : specifies the I2C address + +To use the SU1 converter as a backlight source the following two properties must +be provided: +- su1-dev : framebuffer phandle +- su1-max-uA : maximum current + +To use the SU2 converter as a backlight source the following two properties must +be provided: +- su2-dev : framebuffer phandle +- su1-max-uA : maximum current + +Additionally one of these properties must be provided to select the type of +feedback used: +- su2-feedback-voltage : voltage feedback is used +- su2-feedback-curr1 : CURR1 input used for current feedback +- su2-feedback-curr2 : CURR2 input used for current feedback +- su2-feedback-curr3 : CURR3 input used for current feedback +- su2-feedback-curr-auto: automatic current feedback selection + +and one of these to select the over-voltage protection pin +- su2-fbprot-lx-sd4 : LX_SD4 is used for over-voltage protection +- su2-fbprot-gpio2 : GPIO2 is used for over-voltage protection +- su2-fbprot-gpio3 : GPIO3 is used for over-voltage protection +- su2-fbprot-gpio4 : GPIO4 is used for over-voltage protection + +If "su2-feedback-curr-auto" is selected, one or more of the following properties +have to be specified: +- su2-auto-curr1 : use CURR1 input for current feedback +- su2-auto-curr2 : use CURR2 input for current feedback +- su2-auto-curr3 : use CURR3 input for current feedback + +Example: + +as3711@40 { + compatible = "ams,as3711"; + reg = <0x40>; + + regulators { + sd4 { + regulator-name = "1.215V"; + regulator-min-microvolt = <1215000>; + regulator-max-microvolt = <1235000>; + }; + ldo2 { + regulator-name = "2.8V CPU"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-boot-on; + }; + }; + + backlight { + compatible = "ams,as3711-bl"; + su2-dev = <&lcdc>; + su2-max-uA = <36000>; + su2-feedback-curr-auto; + su2-fbprot-gpio4; + su2-auto-curr1; + su2-auto-curr2; + su2-auto-curr3; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/as3722.txt b/Documentation/devicetree/bindings/mfd/as3722.txt new file mode 100644 index 000000000..4f64b2a73 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/as3722.txt @@ -0,0 +1,213 @@ +* ams AS3722 Power management IC. + +Required properties: +------------------- +- compatible: Must be "ams,as3722". +- reg: I2C device address. +- interrupt-controller: AS3722 has internal interrupt controller which takes the + interrupt request from internal sub-blocks like RTC, regulators, GPIOs as well + as external input. +- #interrupt-cells: Should be set to 2 for IRQ number and flags. + The first cell is the IRQ number. IRQ numbers for different interrupt source + of AS3722 are defined at dt-bindings/mfd/as3722.h + The second cell is the flags, encoded as the trigger masks from binding document + interrupts.txt, using dt-bindings/irq. + +Optional properties: +-------------------- +- ams,enable-internal-int-pullup: Boolean property, to enable internal pullup on + interrupt pin. Missing this will disable internal pullup on INT pin. +- ams,enable-internal-i2c-pullup: Boolean property, to enable internal pullup on + i2c scl/sda pins. Missing this will disable internal pullup on i2c + scl/sda lines. + +Optional submodule and their properties: +======================================= + +Pinmux and GPIO: +=============== +Device has 8 GPIO pins which can be configured as GPIO as well as the special IO +functions. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Following are properties which is needed if GPIO and pinmux functionality +is required: + Required properties: + ------------------- + - gpio-controller: Marks the device node as a GPIO controller. + - #gpio-cells: Number of GPIO cells. Refer to binding document + gpio/gpio.txt + + Optional properties: + -------------------- + Following properties are require if pin control setting is required + at boot. + - pinctrl-names: A pinctrl state named "default" be defined, using the + bindings in pinctrl/pinctrl-binding.txt. + - pinctrl[0...n]: Properties to contain the phandle that refer to + different nodes of pin control settings. These nodes represents + the pin control setting of state 0 to state n. Each of these + nodes contains different subnodes to represents some desired + configuration for a list of pins. This configuration can + include the mux function to select on those pin(s), and + various pin configuration parameters, such as pull-up, + open drain. + + Each subnode have following properties: + Required properties: + - pins: List of pins. Valid values of pins properties are: + gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, + gpio6, gpio7 + + Optional properties: + function, bias-disable, bias-pull-up, bias-pull-down, + bias-high-impedance, drive-open-drain. + + Valid values for function properties are: + gpio, interrupt-out, gpio-in-interrupt, + vsup-vbat-low-undebounce-out, + vsup-vbat-low-debounce-out, + voltage-in-standby, oc-pg-sd0, oc-pg-sd6, + powergood-out, pwm-in, pwm-out, clk32k-out, + watchdog-in, soft-reset-in + +Regulators: +=========== +Device has multiple DCDC and LDOs. The node "regulators" is require if regulator +functionality is needed. + +Following are properties of regulator subnode. + + Optional properties: + ------------------- + The input supply of regulators are the optional properties on the + regulator node. The input supply of these regulators are provided + through following properties: + vsup-sd2-supply: Input supply for SD2. + vsup-sd3-supply: Input supply for SD3. + vsup-sd4-supply: Input supply for SD4. + vsup-sd5-supply: Input supply for SD5. + vin-ldo0-supply: Input supply for LDO0. + vin-ldo1-6-supply: Input supply for LDO1 and LDO6. + vin-ldo2-5-7-supply: Input supply for LDO2, LDO5 and LDO7. + vin-ldo3-4-supply: Input supply for LDO3 and LDO4. + vin-ldo9-10-supply: Input supply for LDO9 and LDO10. + vin-ldo11-supply: Input supply for LDO11. + + Optional sub nodes for regulators: + --------------------------------- + The subnodes name is the name of regulator and it must be one of: + sd[0-6], ldo[0-7], ldo[9-11] + + Each sub-node should contain the constraints and initialization + information for that regulator. See regulator.txt for a description + of standard properties for these sub-nodes. + Additional optional custom properties are listed below. + ams,ext-control: External control of the rail. The option of + this properties will tell which external input is + controlling this rail. Valid values are 0, 1, 2 ad 3. + 0: There is no external control of this rail. + 1: Rail is controlled by ENABLE1 input pin. + 2: Rail is controlled by ENABLE2 input pin. + 3: Rail is controlled by ENABLE3 input pin. + Missing this property on DT will be assume as no + external control. The external control pin macros + are defined @dt-bindings/mfd/as3722.h + + ams,enable-tracking: Enable tracking with SD1, only supported + by LDO3. + +Power-off: +========= +AS3722 supports the system power off by turning off all its rail. This +is provided through pm_power_off. +The device node should have the following properties to enable this +functionality +ams,system-power-controller: Boolean, to enable the power off functionality + through this device. + +Example: +-------- +#include <dt-bindings/mfd/as3722.h> +... +ams3722 { + compatible = "ams,as3722"; + reg = <0x48>; + + ams,system-power-controller; + + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <2>; + + gpio-controller; + #gpio-cells = <2>; + + pinctrl-names = "default"; + pinctrl-0 = <&as3722_default>; + + as3722_default: pinmux { + gpio0 { + pins = "gpio0"; + function = "gpio"; + bias-pull-down; + }; + + gpio1_2_4_7 { + pins = "gpio1", "gpio2", "gpio4", "gpio7"; + function = "gpio"; + bias-pull-up; + }; + + gpio5 { + pins = "gpio5"; + function = "clk32k_out"; + }; + } + + regulators { + vsup-sd2-supply = <...>; + ... + + sd0 { + regulator-name = "vdd_cpu"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + ams,ext-control = <2>; + }; + + sd1 { + regulator-name = "vdd_core"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + ams,ext-control = <1>; + }; + + sd2 { + regulator-name = "vddio_ddr"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + sd4 { + regulator-name = "avdd-hdmi-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + }; + + sd5 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + .... + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt b/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt new file mode 100644 index 000000000..a28569540 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-gpbr.txt @@ -0,0 +1,15 @@ +* Device tree bindings for Atmel GPBR (General Purpose Backup Registers) + +The GPBR are a set of battery-backed registers. + +Required properties: +- compatible: "atmel,at91sam9260-gpbr", "syscon" +- reg: contains offset/length value of the GPBR memory + region. + +Example: + +gpbr: gpbr@fffffd50 { + compatible = "atmel,at91sam9260-gpbr", "syscon"; + reg = <0xfffffd50 0x10>; +}; diff --git a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt new file mode 100644 index 000000000..f64de95a8 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt @@ -0,0 +1,51 @@ +Device-Tree bindings for Atmel's HLCDC (High LCD Controller) MFD driver + +Required properties: + - compatible: value should be one of the following: + "atmel,sama5d3-hlcdc" + - reg: base address and size of the HLCDC device registers. + - clock-names: the name of the 3 clocks requested by the HLCDC device. + Should contain "periph_clk", "sys_clk" and "slow_clk". + - clocks: should contain the 3 clocks requested by the HLCDC device. + - interrupts: should contain the description of the HLCDC interrupt line + +The HLCDC IP exposes two subdevices: + - a PWM chip: see ../pwm/atmel-hlcdc-pwm.txt + - a Display Controller: see ../drm/atmel-hlcdc-dc.txt + +Example: + + hlcdc: hlcdc@f0030000 { + compatible = "atmel,sama5d3-hlcdc"; + reg = <0xf0030000 0x2000>; + clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>; + clock-names = "periph_clk","sys_clk", "slow_clk"; + interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>; + status = "disabled"; + + hlcdc-display-controller { + compatible = "atmel,hlcdc-display-controller"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + hlcdc_panel_output: endpoint@0 { + reg = <0>; + remote-endpoint = <&panel_input>; + }; + }; + }; + + hlcdc_pwm: hlcdc-pwm { + compatible = "atmel,hlcdc-pwm"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lcd_pwm>; + #pwm-cells = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/atmel-matrix.txt b/Documentation/devicetree/bindings/mfd/atmel-matrix.txt new file mode 100644 index 000000000..e3ef50ca0 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-matrix.txt @@ -0,0 +1,24 @@ +* Device tree bindings for Atmel Bus Matrix + +The Bus Matrix registers are used to configure Atmel SoCs internal bus +behavior (master/slave priorities, undefined burst length type, ...) + +Required properties: +- compatible: Should be one of the following + "atmel,at91sam9260-matrix", "syscon" + "atmel,at91sam9261-matrix", "syscon" + "atmel,at91sam9263-matrix", "syscon" + "atmel,at91sam9rl-matrix", "syscon" + "atmel,at91sam9g45-matrix", "syscon" + "atmel,at91sam9n12-matrix", "syscon" + "atmel,at91sam9x5-matrix", "syscon" + "atmel,sama5d3-matrix", "syscon" +- reg: Contains offset/length value of the Bus Matrix + memory region. + +Example: + +matrix: matrix@ffffec00 { + compatible = "atmel,sama5d3-matrix", "syscon"; + reg = <0xffffec00 0x200>; +}; diff --git a/Documentation/devicetree/bindings/mfd/atmel-smc.txt b/Documentation/devicetree/bindings/mfd/atmel-smc.txt new file mode 100644 index 000000000..26eeed373 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/atmel-smc.txt @@ -0,0 +1,19 @@ +* Device tree bindings for Atmel SMC (Static Memory Controller) + +The SMC registers are used to configure Atmel EBI (External Bus Interface) +to interface with standard memory devices (NAND, NOR, SRAM or specialized +devices like FPGAs). + +Required properties: +- compatible: Should be one of the following + "atmel,at91sam9260-smc", "syscon" + "atmel,sama5d3-smc", "syscon" +- reg: Contains offset/length value of the SMC memory + region. + +Example: + +smc: smc@ffffc000 { + compatible = "atmel,sama5d3-smc", "syscon"; + reg = <0xffffc000 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt new file mode 100644 index 000000000..98685f291 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -0,0 +1,96 @@ +AXP202/AXP209 device tree bindings + +The axp20x family current members : +axp202 (X-Powers) +axp209 (X-Powers) + +Required properties: +- compatible: "x-powers,axp202" or "x-powers,axp209" +- reg: The I2C slave address for the AXP chip +- interrupt-parent: The parent interrupt controller +- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin +- interrupt-controller: axp20x has its own internal IRQs +- #interrupt-cells: Should be set to 1 + +Optional properties: +- x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz + (range: 750-1875). Default: 1.5MHz +- <input>-supply: a phandle to the regulator supply node. May be omitted if + inputs are unregulated, such as using the IPSOUT output + from the PMIC. + +- regulators: A node that houses a sub-node for each regulator. Regulators + not used but preferred to be managed by the OS should be + listed as well. + See Documentation/devicetree/bindings/regulator/regulator.txt + for more information on standard regulator bindings. + +Optional properties for DCDC regulators: +- x-powers,dcdc-workmode: 1 for PWM mode, 0 for AUTO (PWM/PFM) mode + Default: Current hardware setting + The DCDC regulators work in a mixed PWM/PFM mode, + using PFM under light loads and switching to PWM + for heavier loads. Forcing PWM mode trades efficiency + under light loads for lower output noise. This + probably makes sense for HiFi audio related + applications that aren't battery constrained. + + +AXP202/AXP209 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC2 : DC-DC buck : vin2-supply +DCDC3 : DC-DC buck : vin3-supply +LDO1 : LDO : acin-supply : always on +LDO2 : LDO : ldo24in-supply : shared supply +LDO3 : LDO : ldo3in-supply +LDO4 : LDO : ldo24in-supply : shared supply +LDO5 : LDO : ldo5in-supply + +Example: + +axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + x-powers,dcdc-freq = <1500>; + + vdd_cpu: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; + }; + + vdd_int_dll: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; + }; + + vdd_rtc: ldo1 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-rtc"; + }; + + avcc: ldo2 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; + }; + + ldo3 { + /* unused but preferred to be managed by OS */ + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/bfticu.txt b/Documentation/devicetree/bindings/mfd/bfticu.txt new file mode 100644 index 000000000..65c90776c --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/bfticu.txt @@ -0,0 +1,25 @@ +KEYMILE bfticu Chassis Management FPGA + +The bfticu is a multifunction device that manages the whole chassis. +Its main functionality is to collect IRQs from the whole chassis and signals +them to a single controller. + +Required properties: +- compatible: "keymile,bfticu" +- interrupt-controller: the bfticu FPGA is an interrupt controller +- interrupts: the main IRQ line to signal the collected IRQs +- #interrupt-cells : is 2 and their usage is compliant to the 2 cells variant + of Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- interrupt-parent: the parent IRQ ctrl the main IRQ is connected to +- reg: access on the parent local bus (chip select, offset in chip select, size) + +Example: + + chassis-mgmt@3,0 { + compatible = "keymile,bfticu"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <3 0 0x100>; + interrupt-parent = <&mpic>; + interrupts = <6 1 0 0>; + }; diff --git a/Documentation/devicetree/bindings/mfd/brcm,bcm59056.txt b/Documentation/devicetree/bindings/mfd/brcm,bcm59056.txt new file mode 100644 index 000000000..be51a15e0 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/brcm,bcm59056.txt @@ -0,0 +1,39 @@ +------------------------------- +BCM590xx Power Management Units +------------------------------- + +Required properties: +- compatible: "brcm,bcm59056" +- reg: I2C slave address +- interrupts: interrupt for the PMU. Generic interrupt client node bindings + are described in interrupt-controller/interrupts.txt + +------------------ +Voltage Regulators +------------------ + +Optional child nodes: +- regulators: container node for regulators following the generic + regulator binding in regulator/regulator.txt + + The valid regulator node names for BCM59056 are: + rfldo, camldo1, camldo2, simldo1, simldo2, sdldo, sdxldo, + mmcldo1, mmcldo2, audldo, micldo, usbldo, vibldo, + csr, iosr1, iosr2, msr, sdsr1, sdsr2, vsr, + gpldo1, gpldo2, gpldo3, gpldo4, gpldo5, gpldo6, + vbus + +Example: + pmu: bcm59056@8 { + compatible = "brcm,bcm59056"; + reg = <0x08>; + interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>; + regulators { + rfldo_reg: rfldo { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + ... + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/cros-ec.txt b/Documentation/devicetree/bindings/mfd/cros-ec.txt new file mode 100644 index 000000000..8009c3d87 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/cros-ec.txt @@ -0,0 +1,65 @@ +ChromeOS Embedded Controller + +Google's ChromeOS EC is a Cortex-M device which talks to the AP and +implements various function such as keyboard and battery charging. + +The EC can be connect through various means (I2C, SPI, LPC) and the +compatible string used depends on the interface. Each connection method has +its own driver which connects to the top level interface-agnostic EC driver. +Other Linux driver (such as cros-ec-keyb for the matrix keyboard) connect to +the top-level driver. + +Required properties (I2C): +- compatible: "google,cros-ec-i2c" +- reg: I2C slave address + +Required properties (SPI): +- compatible: "google,cros-ec-spi" +- reg: SPI chip select + +Optional properties (SPI): +- google,cros-ec-spi-msg-delay: Some implementations of the EC require some + additional processing time in order to accept new transactions. If the delay + between transactions is not long enough the EC may not be able to respond + properly to subsequent transactions and cause them to hang. This property + specifies the delay, in usecs, introduced between transactions to account + for the time required by the EC to get back into a state in which new data + can be accepted. + +Required properties (LPC): +- compatible: "google,cros-ec-lpc" +- reg: List of (IO address, size) pairs defining the interface uses + + +Example for I2C: + +i2c@12CA0000 { + cros-ec@1e { + reg = <0x1e>; + compatible = "google,cros-ec-i2c"; + interrupts = <14 0>; + interrupt-parent = <&wakeup_eint>; + wakeup-source; + }; + + +Example for SPI: + +spi@131b0000 { + ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0x0>; + interrupts = <14 0>; + interrupt-parent = <&wakeup_eint>; + wakeup-source; + spi-max-frequency = <5000000>; + controller-data { + cs-gpio = <&gpf0 3 4 3 0>; + samsung,spi-cs; + samsung,spi-feedback-delay = <2>; + }; + }; +}; + + +Example for LPC is not supplied as it is not yet implemented. diff --git a/Documentation/devicetree/bindings/mfd/da9052-i2c.txt b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt new file mode 100644 index 000000000..1857f4a6b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/da9052-i2c.txt @@ -0,0 +1,60 @@ +* Dialog DA9052/53 Power Management Integrated Circuit (PMIC) + +Required properties: +- compatible : Should be "dlg,da9052", "dlg,da9053-aa", + "dlg,da9053-ab", or "dlg,da9053-bb" + +Sub-nodes: +- regulators : Contain the regulator nodes. The DA9052/53 regulators are + bound using their names as listed below: + + buck0 : regulator BUCK0 + buck1 : regulator BUCK1 + buck2 : regulator BUCK2 + buck3 : regulator BUCK3 + ldo4 : regulator LDO4 + ldo5 : regulator LDO5 + ldo6 : regulator LDO6 + ldo7 : regulator LDO7 + ldo8 : regulator LDO8 + ldo9 : regulator LDO9 + ldo10 : regulator LDO10 + ldo11 : regulator LDO11 + ldo12 : regulator LDO12 + ldo13 : regulator LDO13 + + The bindings details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +Examples: + +i2c@63fc8000 { /* I2C1 */ + status = "okay"; + + pmic: dialog@48 { + compatible = "dlg,da9053-aa"; + reg = <0x48>; + + regulators { + buck0 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2075000>; + }; + + buck1 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <2075000>; + }; + + buck2 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <2500000>; + }; + + buck3 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <2500000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/da9055.txt b/Documentation/devicetree/bindings/mfd/da9055.txt new file mode 100644 index 000000000..6dab34d34 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/da9055.txt @@ -0,0 +1,72 @@ +* Dialog DA9055 Power Management Integrated Circuit (PMIC) + +DA9055 consists of a large and varied group of sub-devices (I2C Only): + +Device Supply Names Description +------ ------------ ----------- +da9055-gpio : : GPIOs +da9055-regulator : : Regulators +da9055-onkey : : On key +da9055-rtc : : RTC +da9055-hwmon : : ADC +da9055-watchdog : : Watchdog + +The CODEC device in DA9055 has a separate, configurable I2C address and so +is instantiated separately from the PMIC. + +For details on accompanying CODEC I2C device, see the following: +Documentation/devicetree/bindings/sound/da9055.txt + +====== + +Required properties: +- compatible : Should be "dlg,da9055-pmic" +- reg: Specifies the I2C slave address (defaults to 0x5a but can be modified) +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the IRQs from da9055 are delivered to. +- interrupts: IRQ line info for da9055 chip. +- interrupt-controller: da9055 has internal IRQs (has own IRQ domain). +- #interrupt-cells: Should be 1, is the local IRQ number for da9055. + +Sub-nodes: +- regulators : Contain the regulator nodes. The DA9055 regulators are + bound using their names as listed below: + + buck1 : regulator BUCK1 + buck2 : regulator BUCK2 + ldo1 : regulator LDO1 + ldo2 : regulator LDO2 + ldo3 : regulator LDO3 + ldo4 : regulator LDO4 + ldo5 : regulator LDO5 + ldo6 : regulator LDO6 + + The bindings details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + + +Example: + + pmic: da9055-pmic@5a { + compatible = "dlg,da9055-pmic"; + reg = <0x5a>; + interrupt-parent = <&intc>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + buck1: BUCK1 { + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <2075000>; + }; + buck2: BUCK2 { + regulator-min-microvolt = <925000>; + regulator-max-microvolt = <2500000>; + }; + ldo1: LDO1 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/da9063.txt b/Documentation/devicetree/bindings/mfd/da9063.txt new file mode 100644 index 000000000..42c6fa6f1 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/da9063.txt @@ -0,0 +1,93 @@ +* Dialog DA9063 Power Management Integrated Circuit (PMIC) + +DA9093 consists of a large and varied group of sub-devices (I2C Only): + +Device Supply Names Description +------ ------------ ----------- +da9063-regulator : : LDOs & BUCKs +da9063-rtc : : Real-Time Clock +da9063-watchdog : : Watchdog + +====== + +Required properties: + +- compatible : Should be "dlg,da9063" +- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be + modified to match the chip's OTP settings). +- interrupt-parent : Specifies the reference to the interrupt controller for + the DA9063. +- interrupts : IRQ line information. +- interrupt-controller + +Sub-nodes: + +- regulators : This node defines the settings for the LDOs and BUCKs. The + DA9063 regulators are bound using their names listed below: + + bcore1 : BUCK CORE1 + bcore2 : BUCK CORE2 + bpro : BUCK PRO + bmem : BUCK MEM + bio : BUCK IO + bperi : BUCK PERI + ldo1 : LDO_1 + ldo2 : LDO_2 + ldo3 : LDO_3 + ldo4 : LDO_4 + ldo5 : LDO_5 + ldo6 : LDO_6 + ldo7 : LDO_7 + ldo8 : LDO_8 + ldo9 : LDO_9 + ldo10 : LDO_10 + ldo11 : LDO_11 + + The component follows the standard regulator framework and the bindings + details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +- rtc : This node defines settings for the Real-Time Clock associated with + the DA9063. There are currently no entries in this binding, however + compatible = "dlg,da9063-rtc" should be added if a node is created. + +- watchdog : This node defines settings for the Watchdog timer associated + with the DA9063. There are currently no entries in this binding, however + compatible = "dlg,da9063-watchdog" should be added if a node is created. + + +Example: + + pmic0: da9063@58 { + compatible = "dlg,da9063" + reg = <0x58>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + + rtc { + compatible = "dlg,da9063-rtc"; + }; + + wdt { + compatible = "dlg,da9063-watchdog"; + }; + + regulators { + DA9063_BCORE1: bcore1 { + regulator-name = "BCORE1"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <500000>; + regulator-max-microamp = <2000000>; + regulator-boot-on; + }; + DA9063_LDO11: ldo11 { + regulator-name = "LDO_11"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3600000>; + regulator-boot-on; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/mfd/da9150.txt b/Documentation/devicetree/bindings/mfd/da9150.txt new file mode 100644 index 000000000..d0588eaa0 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/da9150.txt @@ -0,0 +1,43 @@ +Dialog Semiconductor DA9150 Combined Charger/Fuel-Gauge MFD bindings + +DA9150 consists of a group of sub-devices: + +Device Description +------ ----------- +da9150-gpadc : General Purpose ADC +da9150-charger : Battery Charger + +====== + +Required properties: +- compatible : Should be "dlg,da9150" +- reg: Specifies the I2C slave address +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the IRQs from da9150 are delivered to. +- interrupts: IRQ line info for da9150 chip. +- interrupt-controller: da9150 has internal IRQs (own IRQ domain). + (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for + further information relating to interrupt properties) + +Sub-devices: +- da9150-gpadc: See Documentation/devicetree/bindings/iio/adc/da9150-gpadc.txt +- da9150-charger: See Documentation/devicetree/bindings/power/da9150-charger.txt + + +Example: + + charger_fg: da9150@58 { + compatible = "dlg,da9150"; + reg = <0x58>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + + gpadc: da9150-gpadc { + ... + }; + + da9150-charger { + ... + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/hi6421.txt b/Documentation/devicetree/bindings/mfd/hi6421.txt new file mode 100644 index 000000000..0d5a4466a --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/hi6421.txt @@ -0,0 +1,38 @@ +* HI6421 Multi-Functional Device (MFD), by HiSilicon Ltd. + +Required parent device properties: +- compatible : contains "hisilicon,hi6421-pmic"; +- reg : register range space of hi6421; + +Supported Hi6421 sub-devices include: + +Device IRQ Names Supply Names Description +------ --------- ------------ ----------- +regulators : None : None : Regulators + +Required child device properties: +None. + +Example: + hi6421 { + compatible = "hisilicon,hi6421-pmic"; + reg = <0xfcc00000 0x0180>; /* 0x60 << 2 */ + + regulators { + // supply for MLC NAND/ eMMC + hi6421_vout0_reg: hi6421_vout0 { + regulator-name = "VOUT0"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + // supply for 26M Oscillator + hi6421_vout1_reg: hi6421_vout1 { + regulator-name = "VOUT1"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/lp3943.txt b/Documentation/devicetree/bindings/mfd/lp3943.txt new file mode 100644 index 000000000..e8591d6b1 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/lp3943.txt @@ -0,0 +1,33 @@ +TI/National Semiconductor LP3943 MFD driver + +Required properties: + - compatible: "ti,lp3943" + - reg: I2C slave address. From 0x60 to 0x67. + +LP3943 consists of two sub-devices, lp3943-gpio and lp3943-pwm. + +For the LP3943 GPIO properties please refer to: +Documentation/devicetree/bindings/gpio/gpio-lp3943.txt + +For the LP3943 PWM properties please refer to: +Documentation/devicetree/bindings/pwm/pwm-lp3943.txt + +Example: + +lp3943@60 { + compatible = "ti,lp3943"; + reg = <0x60>; + + gpioex: gpio { + compatible = "ti,lp3943-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + pwm3943: pwm { + compatible = "ti,lp3943-pwm"; + #pwm-cells = <2>; + ti,pwm0 = <8 9 10>; + ti,pwm1 = <15>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max14577.txt b/Documentation/devicetree/bindings/mfd/max14577.txt new file mode 100644 index 000000000..236264c10 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max14577.txt @@ -0,0 +1,146 @@ +Maxim MAX14577/77836 Multi-Function Device + +MAX14577 is a Multi-Function Device with Micro-USB Interface Circuit, Li+ +Battery Charger and SFOUT LDO output for powering USB devices. It is +interfaced to host controller using I2C. + +MAX77836 additionally contains PMIC (with two LDO regulators) and Fuel Gauge. + + +Required properties: +- compatible : Must be "maxim,max14577" or "maxim,max77836". +- reg : I2C slave address for the max14577 chip (0x25 for max14577/max77836) +- interrupts : IRQ line for the chip. +- interrupt-parent : The parent interrupt controller. + + +Required nodes: + - charger : + Node for configuring the charger driver. + Required properties: + - compatible : "maxim,max14577-charger" + or "maxim,max77836-charger" + - maxim,fast-charge-uamp : Current in uA for Fast Charge; + Valid values: + - for max14577: 90000 - 950000; + - for max77836: 45000 - 475000; + - maxim,eoc-uamp : Current in uA for End-Of-Charge mode; + Valid values: + - for max14577: 50000 - 200000; + - for max77836: 5000 - 100000; + - maxim,ovp-uvolt : OverVoltage Protection Threshold in uV; + In an overvoltage condition, INT asserts and charging + stops. Valid values: + - 6000000, 6500000, 7000000, 7500000; + - maxim,constant-uvolt : Battery Constant Voltage in uV; + Valid values: + - 4000000 - 4280000 (step by 20000); + - 4350000; + + +Optional nodes: +- max14577-muic/max77836-muic : + Node used only by extcon consumers. + Required properties: + - compatible : "maxim,max14577-muic" or "maxim,max77836-muic" + +- regulators : + Required properties: + - compatible : "maxim,max14577-regulator" + or "maxim,max77836-regulator" + + May contain a sub-node per regulator from the list below. Each + sub-node should contain the constraints and initialization information + for that regulator. See regulator.txt for a description of standard + properties for these sub-nodes. + + List of valid regulator names: + - for max14577: CHARGER, SAFEOUT. + - for max77836: CHARGER, SAFEOUT, LDO1, LDO2. + + The SAFEOUT is a fixed voltage regulator so there is no need to specify + voltages for it. + + +Example: + +#include <dt-bindings/interrupt-controller/irq.h> + +max14577@25 { + compatible = "maxim,max14577"; + reg = <0x25>; + interrupt-parent = <&gpx1>; + interrupts = <5 IRQ_TYPE_NONE>; + + muic: max14577-muic { + compatible = "maxim,max14577-muic"; + }; + + regulators { + compatible = "maxim,max14577-regulator"; + + SAFEOUT { + regulator-name = "SAFEOUT"; + }; + CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <90000>; + regulator-max-microamp = <950000>; + regulator-boot-on; + }; + }; + + charger { + compatible = "maxim,max14577-charger"; + + maxim,constant-uvolt = <4350000>; + maxim,fast-charge-uamp = <450000>; + maxim,eoc-uamp = <50000>; + maxim,ovp-uvolt = <6500000>; + }; +}; + + +max77836@25 { + compatible = "maxim,max77836"; + reg = <0x25>; + interrupt-parent = <&gpx1>; + interrupts = <5 IRQ_TYPE_NONE>; + + muic: max77836-muic { + compatible = "maxim,max77836-muic"; + }; + + regulators { + compatible = "maxim,max77836-regulator"; + + SAFEOUT { + regulator-name = "SAFEOUT"; + }; + CHARGER { + regulator-name = "CHARGER"; + regulator-min-microamp = <90000>; + regulator-max-microamp = <950000>; + regulator-boot-on; + }; + LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3950000>; + }; + }; + + charger { + compatible = "maxim,max77836-charger"; + + maxim,constant-uvolt = <4350000>; + maxim,fast-charge-uamp = <225000>; + maxim,eoc-uamp = <7500>; + maxim,ovp-uvolt = <6500000>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt new file mode 100644 index 000000000..e39f0bc1f --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -0,0 +1,82 @@ +Maxim MAX77686 multi-function device + +MAX77686 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is +interfaced to host controller using i2c interface. PMIC and Charger submodules +are addressed using same i2c slave address whereas RTC submodule uses +different i2c slave address,presently for which we are statically creating i2c +client while probing.This document describes the binding for mfd device and +PMIC submodule. + +Binding for the built-in 32k clock generator block is defined separately +in bindings/clk/maxim,max77686.txt file. + +Required properties: +- compatible : Must be "maxim,max77686"; +- reg : Specifies the i2c slave address of PMIC block. +- interrupts : This i2c device has an IRQ line connected to the main SoC. +- interrupt-parent : The parent interrupt controller. + +Optional node: +- voltage-regulators : The regulators of max77686 have to be instantiated + under subnode named "voltage-regulators" using the following format. + + regulator_name { + regulator-compatible = LDOn/BUCKn + standard regulator constraints.... + }; + refer Documentation/devicetree/bindings/regulator/regulator.txt + + The regulator-compatible property of regulator should initialized with string +to get matched with their hardware counterparts as follow: + + -LDOn : for LDOs, where n can lie in range 1 to 26. + example: LDO1, LDO2, LDO26. + -BUCKn : for BUCKs, where n can lie in range 1 to 9. + example: BUCK1, BUCK5, BUCK9. + + Regulators which can be turned off during system suspend: + -LDOn : 2, 6-8, 10-12, 14-16, + -BUCKn : 1-4. + Use standard regulator bindings for it ('regulator-off-in-suspend'). + + LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable + control. To turn this feature on this property must be added to the regulator + sub-node: + - maxim,ena-gpios : one GPIO specifier enable control (the gpio + flags are actually ignored and always + ACTIVE_HIGH is used) + +Example: + + max77686@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + + voltage-regulators { + ldo11_reg { + regulator-compatible = "LDO11"; + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + regulator-always-on; + }; + + buck1_reg { + regulator-compatible = "BUCK1"; + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck9_reg { + regulator-compatible = "BUCK9"; + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1200000>; + maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>; + }; + } diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt new file mode 100644 index 000000000..38e64405e --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -0,0 +1,121 @@ +Maxim MAX77693 multi-function device + +MAX77693 is a Multifunction device with the following submodules: +- PMIC, +- CHARGER, +- LED, +- MUIC, +- HAPTIC + +It is interfaced to host controller using i2c. +This document describes the bindings for the mfd device. + +Required properties: +- compatible : Must be "maxim,max77693". +- reg : Specifies the i2c slave address of PMIC block. +- interrupts : This i2c device has an IRQ line connected to the main SoC. +- interrupt-parent : The parent interrupt controller. + +Optional properties: +- regulators : The regulators of max77693 have to be instantiated under subnod + named "regulators" using the following format. + + regulators { + regualtor-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER + standard regulator constratints[*]. + }; + + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + +- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide + users with tactile feedback. PWM period and duty-cycle are varied in + order to provide the approprite level of feedback. + + Required properties: + - compatible : Must be "maxim,max77693-hpatic" + - haptic-supply : power supply for the haptic motor + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + - pwms : phandle to the physical PWM(Pulse Width Modulation) device. + PWM properties should be named "pwms". And number of cell is different + for each pwm device. + To get more informations, please refer to documentaion. + [*] refer Documentation/devicetree/bindings/pwm/pwm.txt + +- charger : Node configuring the charger driver. + If present, required properties: + - compatible : Must be "maxim,max77693-charger". + + Optional properties (if not set, defaults will be used): + - maxim,constant-microvolt : Battery constant voltage in uV. The charger + will operate in fast charge constant current mode till battery voltage + reaches this level. Then the charger will switch to fast charge constant + voltage mode. Also vsys (system voltage) will be set to this value when + DC power is supplied but charger is not enabled. + Valid values: 3650000 - 4400000, step by 25000 (rounded down) + Default: 4200000 + + - maxim,min-system-microvolt : Minimal system voltage in uV. + Valid values: 3000000 - 3700000, step by 100000 (rounded down) + Default: 3600000 + + - maxim,thermal-regulation-celsius : Temperature in Celsius for entering + high temperature charging mode. If die temperature exceeds this value + the charging current will be reduced by 105 mA/Celsius. + Valid values: 70, 85, 100, 115 + Default: 100 + + - maxim,battery-overcurrent-microamp : Overcurrent protection threshold + in uA (current from battery to system). + Valid values: 2000000 - 3500000, step by 250000 (rounded down) + Default: 3500000 + + - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for + triggering input voltage regulation loop. If input voltage decreases + below this value, the input current will be reduced to reach the + threshold voltage. + Valid values: 4300000, 4700000, 4800000, 4900000 + Default: 4300000 + +Example: + max77693@66 { + compatible = "maxim,max77693"; + reg = <0x66>; + interrupt-parent = <&gpx1>; + interrupts = <5 2>; + + regulators { + esafeout@1 { + regulator-compatible = "ESAFEOUT1"; + regulator-name = "ESAFEOUT1"; + regulator-boot-on; + }; + esafeout@2 { + regulator-compatible = "ESAFEOUT2"; + regulator-name = "ESAFEOUT2"; + }; + charger@0 { + regulator-compatible = "CHARGER"; + regulator-name = "CHARGER"; + regulator-min-microamp = <60000>; + regulator-max-microamp = <2580000>; + regulator-boot-on; + }; + }; + + haptic { + compatible = "maxim,max77693-haptic"; + haptic-supply = <&haptic_supply>; + pwms = <&pwm 0 40000 0>; + pwm-names = "haptic"; + }; + + charger { + compatible = "maxim,max77693-charger"; + + maxim,constant-microvolt = <4200000>; + maxim,min-system-microvolt = <3600000>; + maxim,thermal-regulation-celsius = <75>; + maxim,battery-overcurrent-microamp = <3000000>; + maxim,charge-input-threshold-microvolt = <4300000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/max8925.txt b/Documentation/devicetree/bindings/mfd/max8925.txt new file mode 100644 index 000000000..4f0dc6638 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max8925.txt @@ -0,0 +1,64 @@ +* Maxim max8925 Power Management IC + +Required parent device properties: +- compatible : "maxim,max8925" +- reg : the I2C slave address for the max8925 chip +- interrupts : IRQ line for the max8925 chip +- interrupt-controller: describes the max8925 as an interrupt + controller (has its own domain) +- #interrupt-cells : should be 1. + - The cell is the max8925 local IRQ number + +Optional parent device properties: +- maxim,tsc-irq: there are 2 IRQ lines for max8925, one is indicated in + interrupts property, the other is indicated here. + +max8925 consists of a large and varied group of sub-devices: + +Device Supply Names Description +------ ------------ ----------- +max8925-onkey : : On key +max8925-rtc : : RTC +max8925-regulator : : Regulators +max8925-backlight : : Backlight +max8925-touch : : Touchscreen +max8925-power : : Charger + +Example: + + pmic: max8925@3c { + compatible = "maxim,max8925"; + reg = <0x3c>; + interrupts = <1>; + interrupt-parent = <&intcmux4>; + interrupt-controller; + #interrupt-cells = <1>; + maxim,tsc-irq = <0>; + + regulators { + SDV1 { + regulator-min-microvolt = <637500>; + regulator-max-microvolt = <1425000>; + regulator-boot-on; + regulator-always-on; + }; + + LDO1 { + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <3900000>; + regulator-boot-on; + regulator-always-on; + }; + + }; + backlight { + maxim,max8925-dual-string = <0>; + }; + charger { + batt-detect = <0>; + topoff-threshold = <1>; + fast-charge = <7>; + no-temp-support = <0>; + no-insert-detect = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt new file mode 100644 index 000000000..23a3650ff --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max8998.txt @@ -0,0 +1,119 @@ +* Maxim MAX8998, National/TI LP3974 multi-function device + +The Maxim MAX8998 is a multi-function device which includes voltage/current +regulators, real time clock, battery charging controller and several +other sub-blocks. It is interfaced using an I2C interface. Each sub-block +is addressed by the host system using different i2c slave address. + +PMIC sub-block +-------------- + +The PMIC sub-block contains a number of voltage and current regulators, +with controllable parameters and dynamic voltage scaling capability. +In addition, it includes a real time clock and battery charging controller +as well. It is accessible at I2C address 0x66. + +Required properties: +- compatible: Should be one of the following: + - "maxim,max8998" for Maxim MAX8998 + - "national,lp3974" or "ti,lp3974" for National/TI LP3974. +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from MAX8998 are routed to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for main interrupt. + - Second interrupt specifier is for power-on/-off interrupt. +- max8998,pmic-buck1-dvs-gpios: GPIO specifiers for two host gpios used + for buck 1 dvs. The format of the gpio specifier depends on the gpio + controller. +- max8998,pmic-buck2-dvs-gpio: GPIO specifier for host gpio used + for buck 2 dvs. The format of the gpio specifier depends on the gpio + controller. +- max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from + the possible 4 options selectable by the dvs gpios. The value of this + property should be 0, 1, 2 or 3. If not specified or out of range, + a default value of 0 is taken. +- max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from + the possible 2 options selectable by the dvs gpios. The value of this + property should be 0 or 1. If not specified or out of range, a default + value of 0 is taken. +- max8998,pmic-buck-voltage-lock: If present, disallows changing of + preprogrammed buck dvfs voltages. + +Additional properties required if max8998,pmic-buck1-dvs-gpios is defined: +- max8998,pmic-buck1-dvs-voltage: An array of 4 voltage values in microvolts + for buck1 regulator that can be selected using dvs gpio. + +Additional properties required if max8998,pmic-buck2-dvs-gpio is defined: +- max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts + for buck2 regulator that can be selected using dvs gpio. + +Regulators: All the regulators of MAX8998 to be instantiated shall be +listed in a child node named 'regulators'. Each regulator is represented +by a child node of the 'regulators' node. + + regulator-name { + /* standard regulator bindings here */ + }; + +Following regulators of the MAX8998 PMIC block are supported. Note that +the 'n' in regulator name, as in LDOn or BUCKn, represents the LDO or BUCK +number as described in MAX8998 datasheet. + + - LDOn + - valid values for n are 2 to 17 + - Example: LDO2, LDO10, LDO17 + - BUCKn + - valid values for n are 1 to 4. + - Example: BUCK1, BUCK2, BUCK3, BUCK4 + + - ENVICHG: Battery Charging Current Monitor Output. This is a fixed + voltage type regulator + + - ESAFEOUT1: (ldo19) + - ESAFEOUT2: (ld020) + +Standard regulator bindings are used inside regulator subnodes. Check + Documentation/devicetree/bindings/regulator/regulator.txt +for more details. + +Example: + + pmic@66 { + compatible = "maxim,max8998-pmic"; + reg = <0x66>; + interrupt-parent = <&wakeup_eint>; + interrupts = <4 0>, <3 0>; + + /* Buck 1 DVS settings */ + max8998,pmic-buck1-default-dvs-idx = <0>; + max8998,pmic-buck1-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */ + <&gpx0 1 1 0 0>; /* SET2 */ + max8998,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1000000>, <950000>; + + /* Buck 2 DVS settings */ + max8998,pmic-buck2-default-dvs-idx = <0>; + max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */ + max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>; + + /* Regulators to instantiate */ + regulators { + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_ARM_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt new file mode 100644 index 000000000..8aba48821 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -0,0 +1,158 @@ +* Freescale MC13783/MC13892 Power Management Integrated Circuit (PMIC) + +Required properties: +- compatible : Should be "fsl,mc13783" or "fsl,mc13892" + +Optional properties: +- fsl,mc13xxx-uses-adc : Indicate the ADC is being used +- fsl,mc13xxx-uses-codec : Indicate the Audio Codec is being used +- fsl,mc13xxx-uses-rtc : Indicate the RTC is being used +- fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used + +Sub-nodes: +- codec: Contain the Audio Codec node. + - adc-port: Contain PMIC SSI port number used for ADC. + - dac-port: Contain PMIC SSI port number used for DAC. +- leds : Contain the led nodes and initial register values in property + "led-control". Number of register depends of used IC, for MC13783 is 6, + for MC13892 is 4, for MC34708 is 1. See datasheet for bits definitions of + these registers. + - #address-cells: Must be 1. + - #size-cells: Must be 0. + Each led node should contain "reg", which used as LED ID (described below). + Optional properties "label" and "linux,default-trigger" is described in + Documentation/devicetree/bindings/leds/common.txt. +- regulators : Contain the regulator nodes. The regulators are bound using + their names as listed below with their registers and bits for enabling. + +MC13783 LED IDs: + 0 : Main display + 1 : AUX display + 2 : Keypad + 3 : Red 1 + 4 : Green 1 + 5 : Blue 1 + 6 : Red 2 + 7 : Green 2 + 8 : Blue 2 + 9 : Red 3 + 10 : Green 3 + 11 : Blue 3 + +MC13892 LED IDs: + 0 : Main display + 1 : AUX display + 2 : Keypad + 3 : Red + 4 : Green + 5 : Blue + +MC34708 LED IDs: + 0 : Charger Red + 1 : Charger Green + +MC13783 regulators: + sw1a : regulator SW1A (register 24, bit 0) + sw1b : regulator SW1B (register 25, bit 0) + sw2a : regulator SW2A (register 26, bit 0) + sw2b : regulator SW2B (register 27, bit 0) + sw3 : regulator SW3 (register 29, bit 20) + vaudio : regulator VAUDIO (register 32, bit 0) + viohi : regulator VIOHI (register 32, bit 3) + violo : regulator VIOLO (register 32, bit 6) + vdig : regulator VDIG (register 32, bit 9) + vgen : regulator VGEN (register 32, bit 12) + vrfdig : regulator VRFDIG (register 32, bit 15) + vrfref : regulator VRFREF (register 32, bit 18) + vrfcp : regulator VRFCP (register 32, bit 21) + vsim : regulator VSIM (register 33, bit 0) + vesim : regulator VESIM (register 33, bit 3) + vcam : regulator VCAM (register 33, bit 6) + vrfbg : regulator VRFBG (register 33, bit 9) + vvib : regulator VVIB (register 33, bit 11) + vrf1 : regulator VRF1 (register 33, bit 12) + vrf2 : regulator VRF2 (register 33, bit 15) + vmmc1 : regulator VMMC1 (register 33, bit 18) + vmmc2 : regulator VMMC2 (register 33, bit 21) + gpo1 : regulator GPO1 (register 34, bit 6) + gpo2 : regulator GPO2 (register 34, bit 8) + gpo3 : regulator GPO3 (register 34, bit 10) + gpo4 : regulator GPO4 (register 34, bit 12) + pwgt1spi : regulator PWGT1SPI (register 34, bit 15) + pwgt2spi : regulator PWGT2SPI (register 34, bit 16) + +MC13892 regulators: + vcoincell : regulator VCOINCELL (register 13, bit 23) + sw1 : regulator SW1 (register 24, bit 0) + sw2 : regulator SW2 (register 25, bit 0) + sw3 : regulator SW3 (register 26, bit 0) + sw4 : regulator SW4 (register 27, bit 0) + swbst : regulator SWBST (register 29, bit 20) + vgen1 : regulator VGEN1 (register 32, bit 0) + viohi : regulator VIOHI (register 32, bit 3) + vdig : regulator VDIG (register 32, bit 9) + vgen2 : regulator VGEN2 (register 32, bit 12) + vpll : regulator VPLL (register 32, bit 15) + vusb2 : regulator VUSB2 (register 32, bit 18) + vgen3 : regulator VGEN3 (register 33, bit 0) + vcam : regulator VCAM (register 33, bit 6) + vvideo : regulator VVIDEO (register 33, bit 12) + vaudio : regulator VAUDIO (register 33, bit 15) + vsd : regulator VSD (register 33, bit 18) + gpo1 : regulator GPO1 (register 34, bit 6) + gpo2 : regulator GPO2 (register 34, bit 8) + gpo3 : regulator GPO3 (register 34, bit 10) + gpo4 : regulator GPO4 (register 34, bit 12) + pwgt1spi : regulator PWGT1SPI (register 34, bit 15) + pwgt2spi : regulator PWGT2SPI (register 34, bit 16) + vusb : regulator VUSB (register 50, bit 3) + + The bindings details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +Examples: + +ecspi@70010000 { /* ECSPI1 */ + fsl,spi-num-chipselects = <2>; + cs-gpios = <&gpio4 24 0>, /* GPIO4_24 */ + <&gpio4 25 0>; /* GPIO4_25 */ + status = "okay"; + + pmic: mc13892@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mc13892"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&gpio0>; + interrupts = <8>; + + leds { + #address-cells = <1>; + #size-cells = <0>; + led-control = <0x000 0x000 0x0e0 0x000>; + + sysled { + reg = <3>; + label = "system:red:live"; + linux,default-trigger = "heartbeat"; + }; + }; + + regulators { + sw1_reg: mc13892__sw1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1375000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: mc13892__sw2 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1850000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt new file mode 100644 index 000000000..15043e652 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/mt6397.txt @@ -0,0 +1,70 @@ +MediaTek MT6397 Multifunction Device Driver + +MT6397 is a multifunction device with the following sub modules: +- Regulator +- RTC +- Audio codec +- GPIO +- Clock + +It is interfaced to host controller using SPI interface by a proprietary hardware +called PMIC wrapper or pwrap. MT6397 MFD is a child device of pwrap. +See the following for pwarp node definitions: +Documentation/devicetree/bindings/soc/pwrap.txt + +This document describes the binding for MFD device and its sub module. + +Required properties: +compatible: "mediatek,mt6397" + +Optional subnodes: + +- rtc + Required properties: + - compatible: "mediatek,mt6397-rtc" +- regulators + Required properties: + - compatible: "mediatek,mt6397-regulator" + see Documentation/devicetree/bindings/regulator/mt6397-regulator.txt +- codec + Required properties: + - compatible: "mediatek,mt6397-codec" +- clk + Required properties: + - compatible: "mediatek,mt6397-clk" + +Example: + pwrap: pwrap@1000f000 { + compatible = "mediatek,mt8135-pwrap"; + + ... + + pmic { + compatible = "mediatek,mt6397"; + + codec: mt6397codec { + compatible = "mediatek,mt6397-codec"; + }; + + regulators { + compatible = "mediatek,mt6397-regulator"; + + mt6397_vpca15_reg: buck_vpca15 { + regulator-compatible = "buck_vpca15"; + regulator-name = "vpca15"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <12500>; + regulator-always-on; + }; + + mt6397_vgp4_reg: ldo_vgp4 { + regulator-compatible = "ldo_vgp4"; + regulator-name = "vgp4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <218>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-host.txt b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt new file mode 100644 index 000000000..4721b2d52 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/omap-usb-host.txt @@ -0,0 +1,103 @@ +OMAP HS USB Host + +Required properties: + +- compatible: should be "ti,usbhs-host" +- reg: should contain one register range i.e. start and length +- ti,hwmods: must contain "usb_host_hs" + +Optional properties: + +- num-ports: number of USB ports. Usually this is automatically detected + from the IP's revision register but can be overridden by specifying + this property. A maximum of 3 ports are supported at the moment. + +- portN-mode: String specifying the port mode for port N, where N can be + from 1 to 3. If the port mode is not specified, that port is treated + as unused. When specified, it must be one of the following. + "ehci-phy", + "ehci-tll", + "ehci-hsic", + "ohci-phy-6pin-datse0", + "ohci-phy-6pin-dpdm", + "ohci-phy-3pin-datse0", + "ohci-phy-4pin-dpdm", + "ohci-tll-6pin-datse0", + "ohci-tll-6pin-dpdm", + "ohci-tll-3pin-datse0", + "ohci-tll-4pin-dpdm", + "ohci-tll-2pin-datse0", + "ohci-tll-2pin-dpdm", + +- single-ulpi-bypass: Must be present if the controller contains a single + ULPI bypass control bit. e.g. OMAP3 silicon <= ES2.1 + +- clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + +- clock-names: should include: + For OMAP3 + * "usbhost_120m_fck" - 120MHz Functional clock. + + For OMAP4+ + * "refclk_60m_int" - 60MHz internal reference clock for UTMI clock mux + * "refclk_60m_ext_p1" - 60MHz external ref. clock for Port 1's UTMI clock mux. + * "refclk_60m_ext_p2" - 60MHz external ref. clock for Port 2's UTMI clock mux + * "utmi_p1_gfclk" - Port 1 UTMI clock mux. + * "utmi_p2_gfclk" - Port 2 UTMI clock mux. + * "usb_host_hs_utmi_p1_clk" - Port 1 UTMI clock gate. + * "usb_host_hs_utmi_p2_clk" - Port 2 UTMI clock gate. + * "usb_host_hs_utmi_p3_clk" - Port 3 UTMI clock gate. + * "usb_host_hs_hsic480m_p1_clk" - Port 1 480MHz HSIC clock gate. + * "usb_host_hs_hsic480m_p2_clk" - Port 2 480MHz HSIC clock gate. + * "usb_host_hs_hsic480m_p3_clk" - Port 3 480MHz HSIC clock gate. + * "usb_host_hs_hsic60m_p1_clk" - Port 1 60MHz HSIC clock gate. + * "usb_host_hs_hsic60m_p2_clk" - Port 2 60MHz HSIC clock gate. + * "usb_host_hs_hsic60m_p3_clk" - Port 3 60MHz HSIC clock gate. + +Required properties if child node exists: + +- #address-cells: Must be 1 +- #size-cells: Must be 1 +- ranges: must be present + +Properties for children: + +The OMAP HS USB Host subsystem contains EHCI and OHCI controllers. +See Documentation/devicetree/bindings/usb/omap-ehci.txt and +omap3-ohci.txt + +Example for OMAP4: + +usbhshost: usbhshost@4a064000 { + compatible = "ti,usbhs-host"; + reg = <0x4a064000 0x800>; + ti,hwmods = "usb_host_hs"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + usbhsohci: ohci@4a064800 { + compatible = "ti,ohci-omap3", "usb-ohci"; + reg = <0x4a064800 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 76 0x4>; + }; + + usbhsehci: ehci@4a064c00 { + compatible = "ti,ehci-omap", "usb-ehci"; + reg = <0x4a064c00 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 77 0x4>; + }; +}; + +&usbhshost { + port1-mode = "ehci-phy"; + port2-mode = "ehci-tll"; + port3-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy 0 &hsusb3_phy>; +}; diff --git a/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt new file mode 100644 index 000000000..c58d70437 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/omap-usb-tll.txt @@ -0,0 +1,27 @@ +OMAP HS USB Host TLL (Transceiver-Less Interface) + +Required properties: + +- compatible : should be "ti,usbhs-tll" +- reg : should contain one register range i.e. start and length +- interrupts : should contain the TLL module's interrupt +- ti,hwmod : must contain "usb_tll_hs" + +Optional properties: + +- clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + +- clock-names: should include: + * "usb_tll_hs_usb_ch0_clk" - USB TLL channel 0 clock + * "usb_tll_hs_usb_ch1_clk" - USB TLL channel 1 clock + * "usb_tll_hs_usb_ch2_clk" - USB TLL channel 2 clock + +Example: + + usbhstll: usbhstll@4a062000 { + compatible = "ti,usbhs-tll"; + reg = <0x4a062000 0x1000>; + interrupts = <78>; + ti,hwmods = "usb_tll_hs"; + }; diff --git a/Documentation/devicetree/bindings/mfd/palmas.txt b/Documentation/devicetree/bindings/mfd/palmas.txt new file mode 100644 index 000000000..eda898978 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/palmas.txt @@ -0,0 +1,53 @@ +* palmas device tree bindings + +The TI palmas family current members :- +twl6035 (palmas) +twl6037 (palmas) +tps65913 (palmas) +tps65914 (palmas) +tps659038 +tps65917 + +Required properties: +- compatible : Should be from the list + ti,twl6035 + ti,twl6036 + ti,twl6037 + ti,tps65913 + ti,tps65914 + ti,tps80036 + ti,tps659038 + ti,tps65917 +and also the generic series names + ti,palmas +- interrupt-controller : palmas has its own internal IRQs +- #interrupt-cells : should be set to 2 for IRQ number and flags + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt +- interrupt-parent : The parent interrupt controller. + +Optional properties: + ti,mux-padX : set the pad register X (1-2) to the correct muxing for the + hardware, if not set will use muxing in OTP. + +Example: + +palmas { + compatible = "ti,twl6035", "ti,palmas"; + reg = <0x48> + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <2>; + + ti,mux-pad1 = <0>; + ti,mux-pad2 = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + pmic { + compatible = "ti,twl6035-pmic", "ti,palmas-pmic"; + .... + }; +} diff --git a/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt new file mode 100644 index 000000000..6ac06c1b9 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.txt @@ -0,0 +1,75 @@ + Qualcomm SPMI PMICs multi-function device bindings + +The Qualcomm SPMI series presently includes PM8941, PM8841 and PMA8084 +PMICs. These PMICs use a QPNP scheme through SPMI interface. +QPNP is effectively a partitioning scheme for dividing the SPMI extended +register space up into logical pieces, and set of fixed register +locations/definitions within these regions, with some of these regions +specifically used for interrupt handling. + +The QPNP PMICs are used with the Qualcomm Snapdragon series SoCs, and are +interfaced to the chip via the SPMI (System Power Management Interface) bus. +Support for multiple independent functions are implemented by splitting the +16-bit SPMI slave address space into 256 smaller fixed-size regions, 256 bytes +each. A function can consume one or more of these fixed-size register regions. + +Required properties: +- compatible: Should contain one of: + "qcom,pm8941", + "qcom,pm8841", + "qcom,pma8084", + "qcom,pm8019", + "qcom,pm8226", + "qcom,pm8110", + "qcom,pma8084", + "qcom,pmi8962", + "qcom,pmd9635", + "qcom,pm8994", + "qcom,pmi8994", + "qcom,pm8916", + "qcom,pm8004", + "qcom,pm8909", + or generalized "qcom,spmi-pmic". +- reg: Specifies the SPMI USID slave address for this device. + For more information see: + Documentation/devicetree/bindings/spmi/spmi.txt + +Required properties for peripheral child nodes: +- compatible: Should contain "qcom,xxx", where "xxx" is a peripheral name. + +Optional properties for peripheral child nodes: +- interrupts: Interrupts are specified as a 4-tuple. For more information + see: + Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt +- interrupt-names: Corresponding interrupt name to the interrupts property + +Each child node of SPMI slave id represents a function of the PMIC. In the +example below the rtc device node represents a peripheral of pm8941 +SID = 0. The regulator device node represents a peripheral of pm8941 SID = 1. + +Example: + + spmi { + compatible = "qcom,spmi-pmic-arb"; + + pm8941@0 { + compatible = "qcom,pm8941", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + + rtc { + compatible = "qcom,rtc"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "alarm"; + }; + }; + + pm8941@1 { + compatible = "qcom,pm8941", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + + regulator { + compatible = "qcom,regulator"; + regulator-name = "8941_boost"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/qcom,tcsr.txt b/Documentation/devicetree/bindings/mfd/qcom,tcsr.txt new file mode 100644 index 000000000..e90519d56 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qcom,tcsr.txt @@ -0,0 +1,22 @@ +QCOM Top Control and Status Register + +Qualcomm devices have a set of registers that provide various control and status +functions for their peripherals. This node is intended to allow access to these +registers via syscon. + +Required properties: +- compatible: Should contain: + "qcom,tcsr-ipq8064", "syscon" for IPQ8064 + "qcom,tcsr-apq8064", "syscon" for APQ8064 + "qcom,tcsr-msm8660", "syscon" for MSM8660 + "qcom,tcsr-msm8960", "syscon" for MSM8960 + "qcom,tcsr-msm8974", "syscon" for MSM8974 + "qcom,tcsr-apq8084", "syscon" for APQ8084 + "qcom,tcsr-msm8916", "syscon" for MSM8916 +- reg: Address range for TCSR registers + +Example: + tcsr: syscon@1a400000 { + compatible = "qcom,tcsr-msm8960", "syscon"; + reg = <0x1a400000 0x100>; + }; diff --git a/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt new file mode 100644 index 000000000..f24f33409 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qcom-pm8xxx.txt @@ -0,0 +1,97 @@ +Qualcomm PM8xxx PMIC multi-function devices + +The PM8xxx family of Power Management ICs are used to provide regulated +voltages and other various functionality to Qualcomm SoCs. + += PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058" + "qcom,pm8921" + +- #address-cells: + Usage: required + Value type: <u32> + Definition: must be 1 + +- #size-cells: + Usage: required + Value type: <u32> + Definition: must be 0 + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: specifies the interrupt that indicates a subdevice + has generated an interrupt (summary interrupt). The + format of the specifier is defined by the binding document + describing the node's interrupt parent. + +- #interrupt-cells: + Usage: required + Value type : <u32> + Definition: must be 2. Specifies the number of cells needed to encode + an interrupt source. The 1st cell contains the interrupt + number. The 2nd cell is the trigger type and level flags + encoded as follows: + + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + +- interrupt-controller: + Usage: required + Value type: <empty> + Definition: identifies this node as an interrupt controller + += SUBCOMPONENTS + +The PMIC contains multiple independent functions, each described in a subnode. +The below bindings specify the set of valid subnodes. + +== Real-Time Clock + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,pm8058-rtc" + "qcom,pm8921-rtc" + "qcom,pm8941-rtc" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: single entry specifying the base address of the RTC registers + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: single entry specifying the RTC's alarm interrupt + +- allow-set-time: + Usage: optional + Value type: <empty> + Definition: indicates that the setting of RTC time is allowed by + the host CPU + += EXAMPLE + + pmicintc: pmic@0 { + compatible = "qcom,pm8921"; + interrupts = <104 8>; + #interrupt-cells = <2>; + interrupt-controller; + #address-cells = <1>; + #size-cells = <0>; + + rtc@11d { + compatible = "qcom,pm8921-rtc"; + reg = <0x11d>; + interrupts = <0x27 0>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt new file mode 100644 index 000000000..5e97a9593 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt @@ -0,0 +1,264 @@ +Qualcomm Resource Power Manager (RPM) + +This driver is used to interface with the Resource Power Manager (RPM) found in +various Qualcomm platforms. The RPM allows each component in the system to vote +for state of the system resources, such as clocks, regulators and bus +frequencies. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,rpm-apq8064" + "qcom,rpm-msm8660" + "qcom,rpm-msm8960" + "qcom,rpm-ipq8064" + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: base address and size of the RPM's message ram + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: three entries specifying the RPM's: + 1. acknowledgement interrupt + 2. error interrupt + 3. wakeup interrupt + +- interrupt-names: + Usage: required + Value type: <string-array> + Definition: must be the three strings "ack", "err" and "wakeup", in order + +- qcom,ipc: + Usage: required + Value type: <prop-encoded-array> + + Definition: three entries specifying the outgoing ipc bit used for + signaling the RPM: + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + + += SUBNODES + +The RPM exposes resources to its subnodes. The below bindings specify the set +of valid subnodes that can operate on these resources. + +== Regulators + +Regulator nodes are identified by their compatible: + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,rpm-pm8058-regulators" + "qcom,rpm-pm8901-regulators" + "qcom,rpm-pm8921-regulators" + +- vdd_l0_l1_lvs-supply: +- vdd_l2_l11_l12-supply: +- vdd_l3_l4_l5-supply: +- vdd_l6_l7-supply: +- vdd_l8-supply: +- vdd_l9-supply: +- vdd_l10-supply: +- vdd_l13_l16-supply: +- vdd_l14_l15-supply: +- vdd_l17_l18-supply: +- vdd_l19_l20-supply: +- vdd_l21-supply: +- vdd_l22-supply: +- vdd_l23_l24_l25-supply: +- vdd_ncp-supply: +- vdd_s0-supply: +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: + Usage: optional (pm8058 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- lvs0_in-supply: +- lvs1_in-supply: +- lvs2_in-supply: +- lvs3_in-supply: +- mvs_in-supply: +- vdd_l0-supply: +- vdd_l1-supply: +- vdd_l2-supply: +- vdd_l3-supply: +- vdd_l4-supply: +- vdd_l5-supply: +- vdd_l6-supply: +- vdd_s0-supply: +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: + Usage: optional (pm8901 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_l1_l2_l12_l18-supply: +- vdd_l3_l15_l17-supply: +- vdd_l4_l14-supply: +- vdd_l5_l8_l16-supply: +- vdd_l6_l7-supply: +- vdd_l9_l11-supply: +- vdd_l10_l22-supply: +- vdd_l21_l23_l29-supply: +- vdd_l24-supply: +- vdd_l25-supply: +- vdd_l26-supply: +- vdd_l27-supply: +- vdd_l28-supply: +- vdd_ncp-supply: +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_s7-supply: +- vdd_s8-supply: +- vin_5vs-supply: +- vin_lvs1_3_6-supply: +- vin_lvs2-supply: +- vin_lvs4_5_7-supply: + Usage: optional (pm8921 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +The regulator node houses sub-nodes for each regulator within the device. Each +sub-node is identified using the node's name, with valid values listed for each +of the pmics below. + +pm8058: + l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, + l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4, + lvs0, lvs1, ncp + +pm8901: + l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3, + mvs + +pm8921: + s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, + l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28, + l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch, + ncp + +The content of each sub-node is defined by the standard binding for regulators - +see regulator.txt - with additional custom properties described below: + +=== Switch-mode Power Supply regulator custom properties + +- bias-pull-down: + Usage: optional + Value type: <empty> + Definition: enable pull down of the regulator when inactive + +- qcom,switch-mode-frequency: + Usage: required + Value type: <u32> + Definition: Frequency (Hz) of the switch-mode power supply; + must be one of: + 19200000, 9600000, 6400000, 4800000, 3840000, 3200000, + 2740000, 2400000, 2130000, 1920000, 1750000, 1600000, + 1480000, 1370000, 1280000, 1200000 + +- qcom,force-mode: + Usage: optional (default if no other qcom,force-mode is specified) + Value type: <u32> + Defintion: indicates that the regulator should be forced to a + particular mode, valid values are: + QCOM_RPM_FORCE_MODE_NONE - do not force any mode + QCOM_RPM_FORCE_MODE_LPM - force into low power mode + QCOM_RPM_FORCE_MODE_HPM - force into high power mode + QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically + select its own mode based on + realtime current draw, only for: + pm8921 smps and ftsmps + +- qcom,power-mode-hysteretic: + Usage: optional + Value type: <empty> + Definition: select that the power supply should operate in hysteretic + mode, instead of the default pwm mode + +=== Low-dropout regulator custom properties + +- bias-pull-down: + Usage: optional + Value type: <empty> + Definition: enable pull down of the regulator when inactive + +- qcom,force-mode: + Usage: optional + Value type: <u32> + Defintion: indicates that the regulator should not be forced to any + particular mode, valid values are: + QCOM_RPM_FORCE_MODE_NONE - do not force any mode + QCOM_RPM_FORCE_MODE_LPM - force into low power mode + QCOM_RPM_FORCE_MODE_HPM - force into high power mode + QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass + mode, i.e. to act as a switch + and not regulate, only for: + pm8921 pldo, nldo and nldo1200 + +=== Negative Charge Pump custom properties + +- qcom,switch-mode-frequency: + Usage: required + Value type: <u32> + Definition: Frequency (Hz) of the swith mode power supply; + must be one of: + 19200000, 9600000, 6400000, 4800000, 3840000, 3200000, + 2740000, 2400000, 2130000, 1920000, 1750000, 1600000, + 1480000, 1370000, 1280000, 1200000 + += EXAMPLE + + #include <dt-bindings/mfd/qcom-rpm.h> + + rpm@108000 { + compatible = "qcom,rpm-msm8960"; + reg = <0x108000 0x1000>; + qcom,ipc = <&apcs 0x8 2>; + + interrupts = <0 19 0>, <0 21 0>, <0 22 0>; + interrupt-names = "ack", "err", "wakeup"; + + regulators { + compatible = "qcom,rpm-pm8921-regulators"; + vdd_l1_l2_l12_l18-supply = <&pm8921_s4>; + + s1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + + bias-pull-down; + + qcom,switch-mode-frequency = <3200000>; + }; + + pm8921_s4: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + + qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/mfd/qriox.txt b/Documentation/devicetree/bindings/mfd/qriox.txt new file mode 100644 index 000000000..f301e2d4c --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/qriox.txt @@ -0,0 +1,17 @@ +KEYMILE qrio Board Control CPLD + +The qrio is a multifunction device that controls the KEYMILE boards based on +the kmp204x design. +It is consists of a reset controller, watchdog timer, LEDs, and 2 IRQ capable +GPIO blocks. + +Required properties: +- compatible: "keymile,qriox" +- reg: access on the parent local bus (chip select, offset in chip select, size) + +Example: + + board-control@1,0 { + compatible = "keymile,qriox"; + reg = <1 0 0x80>; + }; diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt new file mode 100644 index 000000000..9e6e2592e --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -0,0 +1,177 @@ +RK808 Power Management Integrated Circuit + +Required properties: +- compatible: "rockchip,rk808" +- reg: I2C slave address +- interrupt-parent: The parent interrupt controller. +- interrupts: the interrupt outputs of the controller. +- #clock-cells: from common clock binding; shall be set to 1 (multiple clock + outputs). See <dt-bindings/clock/rockchip,rk808.h> for clock IDs. + +Optional properties: +- clock-output-names: From common clock binding to override the + default output clock name +- rockchip,system-power-controller: Telling whether or not this pmic is controlling + the system power. +- vcc1-supply: The input supply for DCDC_REG1 +- vcc2-supply: The input supply for DCDC_REG2 +- vcc3-supply: The input supply for DCDC_REG3 +- vcc4-supply: The input supply for DCDC_REG4 +- vcc6-supply: The input supply for LDO_REG1 and LDO_REG2 +- vcc7-supply: The input supply for LDO_REG3 and LDO_REG7 +- vcc8-supply: The input supply for SWITCH_REG1 +- vcc9-supply: The input supply for LDO_REG4 and LDO_REG5 +- vcc10-supply: The input supply for LDO_REG6 +- vcc11-supply: The input supply for LDO_REG8 +- vcc12-supply: The input supply for SWITCH_REG2 + +Regulators: All the regulators of RK808 to be instantiated shall be +listed in a child node named 'regulators'. Each regulator is represented +by a child node of the 'regulators' node. + + regulator-name { + /* standard regulator bindings here */ + }; + +Following regulators of the RK808 PMIC block are supported. Note that +the 'n' in regulator name, as in DCDC_REGn or LDOn, represents the DCDC or LDO +number as described in RK808 datasheet. + + - DCDC_REGn + - valid values for n are 1 to 4. + - LDO_REGn + - valid values for n are 1 to 8. + - SWITCH_REGn + - valid values for n are 1 to 2 + +Standard regulator bindings are used inside regulator subnodes. Check + Documentation/devicetree/bindings/regulator/regulator.txt +for more details + +Example: + rk808: pmic@1b { + compatible = "rockchip,rk808"; + clock-output-names = "xin32k", "rk808-clkout2"; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int>; + reg = <0x1b>; + rockchip,system-power-controller; + wakeup-source; + #clock-cells = <1>; + + vcc8-supply = <&vcc_18>; + vcc9-supply = <&vcc_io>; + vcc10-supply = <&vcc_io>; + vcc12-supply = <&vcc_io>; + vddio-supply = <&vccio_pmu>; + + regulators { + vdd_cpu: DCDC_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <750000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd_arm"; + }; + + vdd_gpu: DCDC_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd_gpu"; + }; + + vcc_ddr: DCDC_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_ddr"; + }; + + vcc_io: DCDC_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_io"; + }; + + vccio_pmu: LDO_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_pmu"; + }; + + vcc_tp: LDO_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc_tp"; + }; + + vdd_10: LDO_REG3 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd_10"; + }; + + vcc18_lcd: LDO_REG4 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc18_lcd"; + }; + + vccio_sd: LDO_REG5 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vccio_sd"; + }; + + vdd10_lcd: LDO_REG6 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-name = "vdd10_lcd"; + }; + + vcc_18: LDO_REG7 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc_18"; + }; + + vcca_codec: LDO_REG8 { + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcca_codec"; + }; + + vcc_wl: SWITCH_REG1 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_wl"; + }; + + vcc_lcd: SWITCH_REG2 { + regulator-always-on; + regulator-boot-on; + regulator-name = "vcc_lcd"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt new file mode 100644 index 000000000..937785a3e --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt @@ -0,0 +1,36 @@ +* Ricoh RN5T618 PMIC + +Ricoh RN5T618 is a power management IC which integrates 3 step-down +DCDC converters, 7 low-dropout regulators, a Li-ion battery charger, +fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled +through a I2C interface. + +Required properties: + - compatible: should be "ricoh,rn5t618" + - reg: the I2C slave address of the device + +Sub-nodes: + - regulators: the node is required if the regulator functionality is + needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1, + LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2. + The common bindings for each individual regulator can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +Example: + + pmic@32 { + compatible = "ricoh,rn5t618"; + reg = <0x32>; + + regulators { + DCDC1 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + DCDC2 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/s2mpa01.txt b/Documentation/devicetree/bindings/mfd/s2mpa01.txt new file mode 100644 index 000000000..c13d3d8c3 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/s2mpa01.txt @@ -0,0 +1,90 @@ + +* Samsung S2MPA01 Voltage and Current Regulator + +The Samsung S2MPA01 is a multi-function device which includes high +efficiency buck converters including Dual-Phase buck converter, various LDOs, +and an RTC. It is interfaced to the host controller using an I2C interface. +Each sub-block is addressed by the host system using different I2C slave +addresses. + +Required properties: +- compatible: Should be "samsung,s2mpa01-pmic". +- reg: Specifies the I2C slave address of the PMIC block. It should be 0x66. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s2mpa01 are delivered to. +- interrupts: An interrupt specifier for the sole interrupt generated by the + device. + +Optional nodes: +- regulators: The regulators of s2mpa01 that have to be instantiated should be + included in a sub-node named 'regulators'. Regulator nodes and constraints + included in this sub-node use the standard regulator bindings which are + documented elsewhere. + +Properties for BUCK regulator nodes: +- regulator-ramp-delay: ramp delay in uV/us. May be 6250, 12500 + (default), 25000, or 50000. May be 0 for disabling the ramp delay on + BUCK{1,2,3,4}. + + In the absence of the regulator-ramp-delay property, the default ramp + delay will be used. + + NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set + for a particular group of BUCKs. So provide same regulator-ramp-delay=<value>. + + The following BUCKs share ramp settings: + * 1 and 6 + * 2 and 4 + * 8, 9, and 10 + +The following are the names of the regulators that the s2mpa01 PMIC block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of s2mpa01. + + - LDOn + - valid values for n are 1 to 26 + - Example: LDO1, LD02, LDO26 + - BUCKn + - valid values for n are 1 to 10. + - Example: BUCK1, BUCK2, BUCK9 + +Example: + + s2mpa01_pmic@66 { + compatible = "samsung,s2mpa01-pmic"; + reg = <0x66>; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDDQ_MMC2"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <50000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt new file mode 100644 index 000000000..57a045016 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -0,0 +1,139 @@ + +* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator + +The Samsung S2MPS11 is a multi-function device which includes voltage and +current regulators, RTC, charger controller and other sub-blocks. It is +interfaced to the host controller using an I2C interface. Each sub-block is +addressed by the host system using different I2C slave addresses. + +Required properties: +- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic" + or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic". +- reg: Specifies the I2C slave address of the pmic block. It should be 0x66. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from s2mps11 are delivered to. +- interrupts: Interrupt specifiers for interrupt sources. + +Optional nodes: +- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 + KHz outputs, so to register these as clocks with common clock framework + instantiate a sub-node named "clocks". It uses the common clock binding + documented in : + [Documentation/devicetree/bindings/clock/clock-bindings.txt] + The s2mps14 provides two (AP/BT) buffered 32.768 KHz outputs. + - #clock-cells: should be 1. + + - The following is the list of clocks generated by the controller. Each clock + is assigned an identifier and client nodes use this identifier to specify + the clock which they consume. + Clock ID Devices + ---------------------------------------------------------- + 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767 + 32KhzCP 1 S2MPS11, S2MPS13, S5M8767 + 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767 + + - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", + "samsung,s2mps14-clk", "samsung,s5m8767-clk" + +- regulators: The regulators of s2mps11 that have to be instantiated should be +included in a sub-node named 'regulators'. Regulator nodes included in this +sub-node should be of the format as listed below. + + regulator_name { + [standard regulator constraints....]; + }; + + regulator-ramp-delay for BUCKs = [6250/12500/25000(default)/50000] uV/us + + BUCK[2/3/4/6] supports disabling ramp delay on hardware, so explicitly + regulator-ramp-delay = <0> can be used for them to disable ramp delay. + In the absence of the regulator-ramp-delay property, the default ramp + delay will be used. + +NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set +for a particular group of BUCKs. So provide same regulator-ramp-delay<value>. +Grouping of BUCKs sharing ramp rate setting is as follow : BUCK[1, 6], +BUCK[3, 4], and BUCK[7, 8, 10] + +On S2MPS14 the LDO10, LDO11 and LDO12 can be configured to external control +over GPIO. To turn this feature on this property must be added to the regulator +sub-node: + - samsung,ext-control-gpios: GPIO specifier for one GPIO + controlling this regulator (enable/disable); +Example: + LDO12 { + regulator-name = "V_EMMC_2.8V"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + samsung,ext-control-gpios = <&gpk0 2 0>; + }; + + +The regulator constraints inside the regulator nodes use the standard regulator +bindings which are documented elsewhere. + +The following are the names of the regulators that the s2mps11 pmic block +supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number +as per the datasheet of s2mps11. + + - LDOn + - valid values for n are: + - S2MPS11: 1 to 38 + - S2MPS13: 1 to 40 + - S2MPS14: 1 to 25 + - S2MPU02: 1 to 28 + - Example: LDO1, LDO2, LDO28 + - BUCKn + - valid values for n are: + - S2MPS11: 1 to 10 + - S2MPS13: 1 to 10 + - S2MPS14: 1 to 5 + - S2MPU02: 1 to 7 + - Example: BUCK1, BUCK2, BUCK9 + +Example: + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + + s2m_osc: clocks { + compatible = "samsung,s2mps11-clk"; + #clock-cells = <1>; + clock-output-names = "xx", "yy", "zz"; + }; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ABB_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + regulator-ramp-delay = <50000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/sky81452.txt b/Documentation/devicetree/bindings/mfd/sky81452.txt new file mode 100644 index 000000000..35181794a --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/sky81452.txt @@ -0,0 +1,35 @@ +SKY81452 bindings + +Required properties: +- compatible : Must be "skyworks,sky81452" +- reg : I2C slave address + +Required child nodes: +- backlight : container node for backlight following the binding + in video/backlight/sky81452-backlight.txt +- regulator : container node for regulators following the binding + in regulator/sky81452-regulator.txt + +Example: + + sky81452@2c { + compatible = "skyworks,sky81452"; + reg = <0x2c>; + + backlight { + compatible = "skyworks,sky81452-backlight"; + name = "pwm-backlight"; + led-sources = <0 1 2 3 6>; + skyworks,ignore-pwm; + skyworks,phase-shift; + skyworks,current-limit = <2300>; + }; + + regulator { + lout { + regulator-name = "sky81452-lout"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <8000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt new file mode 100644 index 000000000..3fb68bfef --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -0,0 +1,29 @@ +* ST Microelectronics STMPE Multi-Functional Device + +STMPE is an MFD device which may expose the following inbuilt devices: gpio, +keypad, touchscreen, adc, pwm, rotator. + +Required properties: + - compatible : "st,stmpe[610|801|811|1601|2401|2403]" + - reg : I2C/SPI address of the device + +Optional properties: + - interrupts : The interrupt outputs from the controller + - interrupt-controller : Marks the device node as an interrupt controller + - interrupt-parent : Specifies which IRQ controller we're connected to + - wakeup-source : Marks the input device as wakable + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + - irq-gpio : If present, which GPIO to use for event IRQ + +Example: + + stmpe1601: stmpe1601@40 { + compatible = "st,stmpe1601"; + reg = <0x40>; + interrupts = <26 0x4>; + interrupt-parent = <&gpio6>; + interrupt-controller; + + wakeup-source; + st,autosleep-timeout = <1024>; + }; diff --git a/Documentation/devicetree/bindings/mfd/sun6i-prcm.txt b/Documentation/devicetree/bindings/mfd/sun6i-prcm.txt new file mode 100644 index 000000000..03c5a551d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/sun6i-prcm.txt @@ -0,0 +1,59 @@ +* Allwinner PRCM (Power/Reset/Clock Management) Multi-Functional Device + +PRCM is an MFD device exposing several Power Management related devices +(like clks and reset controllers). + +Required properties: + - compatible: "allwinner,sun6i-a31-prcm" or "allwinner,sun8i-a23-prcm" + - reg: The PRCM registers range + +The prcm node may contain several subdevices definitions: + - see Documentation/devicetree/clk/sunxi.txt for clock devices + - see Documentation/devicetree/reset/allwinner,sunxi-clock-reset.txt for reset + controller devices + + +Example: + + prcm: prcm@01f01400 { + compatible = "allwinner,sun6i-a31-prcm"; + reg = <0x01f01400 0x200>; + + /* Put subdevices here */ + ar100: ar100_clk { + compatible = "allwinner,sun6i-a31-ar100-clk"; + #clock-cells = <0>; + clocks = <&osc32k>, <&osc24M>, <&pll6>, <&pll6>; + }; + + ahb0: ahb0_clk { + compatible = "fixed-factor-clock"; + #clock-cells = <0>; + clock-div = <1>; + clock-mult = <1>; + clocks = <&ar100_div>; + clock-output-names = "ahb0"; + }; + + apb0: apb0_clk { + compatible = "allwinner,sun6i-a31-apb0-clk"; + #clock-cells = <0>; + clocks = <&ahb0>; + clock-output-names = "apb0"; + }; + + apb0_gates: apb0_gates_clk { + compatible = "allwinner,sun6i-a31-apb0-gates-clk"; + #clock-cells = <1>; + clocks = <&apb0>; + clock-output-names = "apb0_pio", "apb0_ir", + "apb0_timer01", "apb0_p2wi", + "apb0_uart", "apb0_1wire", + "apb0_i2c"; + }; + + apb0_rst: apb0_rst { + compatible = "allwinner,sun6i-a31-clock-reset"; + #reset-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/syscon.txt b/Documentation/devicetree/bindings/mfd/syscon.txt new file mode 100644 index 000000000..fe8150bb3 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/syscon.txt @@ -0,0 +1,20 @@ +* System Controller Registers R/W driver + +System controller node represents a register region containing a set +of miscellaneous registers. The registers are not cohesive enough to +represent as any specific type of device. The typical use-case is for +some other node's driver, or platform-specific code, to acquire a +reference to the syscon node (e.g. by phandle, node path, or search +using a specific compatible value), interrogate the node (or associated +OS driver) to determine the location of the registers, and access the +registers directly. + +Required properties: +- compatible: Should contain "syscon". +- reg: the register region can be accessed from syscon + +Examples: +gpr: iomuxc-gpr@020e0000 { + compatible = "fsl,imx6q-iomuxc-gpr", "syscon"; + reg = <0x020e0000 0x38>; +}; diff --git a/Documentation/devicetree/bindings/mfd/tc3589x.txt b/Documentation/devicetree/bindings/mfd/tc3589x.txt new file mode 100644 index 000000000..6fcedba46 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tc3589x.txt @@ -0,0 +1,107 @@ +* Toshiba TC3589x multi-purpose expander + +The Toshiba TC3589x series are I2C-based MFD devices which may expose the +following built-in devices: gpio, keypad, rotator (vibrator), PWM (for +e.g. LEDs or vibrators) The included models are: + +- TC35890 +- TC35892 +- TC35893 +- TC35894 +- TC35895 +- TC35896 + +Required properties: + - compatible : must be "toshiba,tc35890", "toshiba,tc35892", "toshiba,tc35893", + "toshiba,tc35894", "toshiba,tc35895" or "toshiba,tc35896" + - reg : I2C address of the device + - interrupt-parent : specifies which IRQ controller we're connected to + - interrupts : the interrupt on the parent the controller is connected to + - interrupt-controller : marks the device node as an interrupt controller + - #interrupt-cells : should be <1>, the first cell is the IRQ offset on this + TC3589x interrupt controller. + +Optional nodes: + +- GPIO + This GPIO module inside the TC3589x has 24 (TC35890, TC35892) or 20 + (other models) GPIO lines. + - compatible : must be "toshiba,tc3589x-gpio" + - interrupts : interrupt on the parent, which must be the tc3589x MFD device + - interrupt-controller : marks the device node as an interrupt controller + - #interrupt-cells : should be <2>, the first cell is the IRQ offset on this + TC3589x GPIO interrupt controller, the second cell is the interrupt flags + in accordance with <dt-bindings/interrupt-controller/irq.h>. The following + flags are valid: + - IRQ_TYPE_LEVEL_LOW + - IRQ_TYPE_LEVEL_HIGH + - IRQ_TYPE_EDGE_RISING + - IRQ_TYPE_EDGE_FALLING + - IRQ_TYPE_EDGE_BOTH + - gpio-controller : marks the device node as a GPIO controller + - #gpio-cells : should be <2>, the first cell is the GPIO offset on this + GPIO controller, the second cell is the flags. + +- Keypad + This keypad is the same on all variants, supporting up to 96 different + keys. The linux-specific properties are modeled on those already existing + in other input drivers. + - compatible : must be "toshiba,tc3589x-keypad" + - debounce-delay-ms : debounce interval in milliseconds + - keypad,num-rows : number of rows in the matrix, see + bindings/input/matrix-keymap.txt + - keypad,num-columns : number of columns in the matrix, see + bindings/input/matrix-keymap.txt + - linux,keymap: the definition can be found in + bindings/input/matrix-keymap.txt + - linux,no-autorepeat: do no enable autorepeat feature. + - linux,wakeup: use any event on keypad as wakeup event. + +Example: + +tc35893@44 { + compatible = "toshiba,tc35893"; + reg = <0x44>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <1>; + + tc3589x_gpio { + compatible = "toshiba,tc3589x-gpio"; + interrupts = <0>; + + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + tc3589x_keypad { + compatible = "toshiba,tc3589x-keypad"; + interrupts = <6>; + debounce-delay-ms = <4>; + keypad,num-columns = <8>; + keypad,num-rows = <8>; + linux,no-autorepeat; + linux,wakeup; + linux,keymap = <0x0301006b + 0x04010066 + 0x06040072 + 0x040200d7 + 0x0303006a + 0x0205000e + 0x0607008b + 0x0500001c + 0x0403000b + 0x03040034 + 0x05020067 + 0x0305006c + 0x040500e7 + 0x0005009e + 0x06020073 + 0x01030039 + 0x07060069 + 0x050500d9>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt b/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt new file mode 100644 index 000000000..20963c76b --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt @@ -0,0 +1,19 @@ +* Device tree bindings for Texas Instruments keystone device state control + +The Keystone II devices have a set of registers that are used to control +the status of its peripherals. This node is intended to allow access to +this functionality. + +Required properties: + +- compatible: "ti,keystone-devctrl", "syscon" + +- reg: contains offset/length value for device state control + registers space. + +Example: + +devctrl: device-state-control@0x02620000 { + compatible = "ti,keystone-devctrl", "syscon"; + reg = <0x02620000 0x1000>; +}; diff --git a/Documentation/devicetree/bindings/mfd/tps6507x.txt b/Documentation/devicetree/bindings/mfd/tps6507x.txt new file mode 100755 index 000000000..8fffa3c5e --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps6507x.txt @@ -0,0 +1,91 @@ +TPS6507x Power Management Integrated Circuit + +Required properties: +- compatible: "ti,tps6507x" +- reg: I2C slave address +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the + given device need to be present. The definition for each of these nodes + is defined using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. + + The valid regulator-compatible values are: + tps6507x: vdcdc1, vdcdc2, vdcdc3, vldo1, vldo2 +- xxx-supply: Input voltage supply regulator. + These entries are required if regulators are enabled for a device. + Missing of these properties can cause the regulator registration + fails. + If some of input supply is powered through battery or always-on + supply then also it is require to have these parameters with proper + node handle of always on power supply. + tps6507x: + vindcdc1_2-supply: VDCDC1 and VDCDC2 input. + vindcdc3-supply : VDCDC3 input. + vldo1_2-supply : VLDO1 and VLDO2 input. + +Regulator Optional properties: +- defdcdc_default: It's property of DCDC2 and DCDC3 regulators. + 0: If defdcdc pin of DCDC2/DCDC3 is pulled to GND. + 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH. + If this property is not defined, it defaults to 0 (not enabled). + +Example: + + pmu: tps6507x@48 { + compatible = "ti,tps6507x"; + reg = <0x48>; + + vindcdc1_2-supply = <&vbat>; + vindcdc3-supply = <...>; + vinldo1_2-supply = <...>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + vdcdc1_reg: regulator@0 { + regulator-compatible = "VDCDC1"; + reg = <0>; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + }; + vdcdc2_reg: regulator@1 { + regulator-compatible = "VDCDC2"; + reg = <1>; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <3450000>; + regulator-always-on; + regulator-boot-on; + defdcdc_default = <1>; + }; + vdcdc3_reg: regulator@2 { + regulator-compatible = "VDCDC3"; + reg = <2>; + regulator-min-microvolt = <950000> + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + defdcdc_default = <1>; + }; + ldo1_reg: regulator@3 { + regulator-compatible = "LDO1"; + reg = <3>; + regulator-min-microvolt = <1710000>; + regulator-max-microvolt = <1890000>; + regulator-always-on; + regulator-boot-on; + }; + ldo2_reg: regulator@4 { + regulator-compatible = "LDO2"; + reg = <4>; + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1320000>; + regulator-always-on; + regulator-boot-on; + }; + }; + + }; diff --git a/Documentation/devicetree/bindings/mfd/tps65910.txt b/Documentation/devicetree/bindings/mfd/tps65910.txt new file mode 100644 index 000000000..38833e63a --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps65910.txt @@ -0,0 +1,201 @@ +TPS65910 Power Management Integrated Circuit + +Required properties: +- compatible: "ti,tps65910" or "ti,tps65911" +- reg: I2C slave address +- interrupts: the interrupt outputs of the controller +- #gpio-cells: number of cells to describe a GPIO, this should be 2. + The first cell is the GPIO number. + The second cell is used to specify additional options <unused>. +- gpio-controller: mark the device as a GPIO controller +- #interrupt-cells: the number of cells to describe an IRQ, this should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Not all regulators for the given + device need to be present. The definition for each of these nodes is defined + using the standard binding for regulators found at + Documentation/devicetree/bindings/regulator/regulator.txt. + The regulator is matched with the regulator-compatible. + + The valid regulator-compatible values are: + tps65910: vrtc, vio, vdd1, vdd2, vdd3, vdig1, vdig2, vpll, vdac, vaux1, + vaux2, vaux33, vmmc, vbb + tps65911: vrtc, vio, vdd1, vdd3, vddctrl, ldo1, ldo2, ldo3, ldo4, ldo5, + ldo6, ldo7, ldo8 + +- xxx-supply: Input voltage supply regulator. + These entries are require if regulators are enabled for a device. Missing of these + properties can cause the regulator registration fails. + If some of input supply is powered through battery or always-on supply then + also it is require to have these parameters with proper node handle of always + on power supply. + tps65910: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: VAUX33 and VMMC input. + vcc4-supply: VAUX1 and VAUX2 input. + vcc5-supply: VPLL and VDAC input. + vcc6-supply: VDIG1 and VDIG2 input. + vcc7-supply: VRTC and VBB input. + vccio-supply: VIO input. + tps65911: + vcc1-supply: VDD1 input. + vcc2-supply: VDD2 input. + vcc3-supply: LDO6, LDO7 and LDO8 input. + vcc4-supply: LDO5 input. + vcc5-supply: LDO3 and LDO4 input. + vcc6-supply: LDO1 and LDO2 input. + vcc7-supply: VRTC input. + vccio-supply: VIO input. + +Optional properties: +- ti,vmbch-threshold: (tps65911) main battery charged threshold + comparator. (see VMBCH_VSEL in TPS65910 datasheet) +- ti,vmbch2-threshold: (tps65911) main battery discharged threshold + comparator. (see VMBCH_VSEL in TPS65910 datasheet) +- ti,en-ck32k-xtal: enable external 32-kHz crystal oscillator (see CK32K_CTRL + in TPS6591X datasheet) +- ti,en-gpio-sleep: enable sleep control for gpios + There should be 9 entries here, one for each gpio. +- ti,system-power-controller: Telling whether or not this pmic is controlling + the system power. + +Regulator Optional properties: +- ti,regulator-ext-sleep-control: enable external sleep + control through external inputs [0 (not enabled), 1 (EN1), 2 (EN2) or 4(EN3)] + If this property is not defined, it defaults to 0 (not enabled). + +Example: + + pmu: tps65910@d2 { + compatible = "ti,tps65910"; + reg = <0xd2>; + interrupt-parent = <&intc>; + interrupts = < 0 118 0x04 >; + + #gpio-cells = <2>; + gpio-controller; + + #interrupt-cells = <2>; + interrupt-controller; + + ti,system-power-controller; + + ti,vmbch-threshold = 0; + ti,vmbch2-threshold = 0; + ti,en-ck32k-xtal; + ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>; + + vcc1-supply = <®_parent>; + vcc2-supply = <&some_reg>; + vcc3-supply = <...>; + vcc4-supply = <...>; + vcc5-supply = <...>; + vcc6-supply = <...>; + vcc7-supply = <...>; + vccio-supply = <...>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + + vdd1_reg: regulator@0 { + regulator-compatible = "vdd1"; + reg = <0>; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <0>; + }; + vdd2_reg: regulator@1 { + regulator-compatible = "vdd2"; + reg = <1>; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <4>; + }; + vddctrl_reg: regulator@2 { + regulator-compatible = "vddctrl"; + reg = <2>; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <0>; + }; + vio_reg: regulator@3 { + regulator-compatible = "vio"; + reg = <3>; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <1>; + }; + ldo1_reg: regulator@4 { + regulator-compatible = "ldo1"; + reg = <4>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo2_reg: regulator@5 { + regulator-compatible = "ldo2"; + reg = <5>; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo3_reg: regulator@6 { + regulator-compatible = "ldo3"; + reg = <6>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo4_reg: regulator@7 { + regulator-compatible = "ldo4"; + reg = <7>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + ti,regulator-ext-sleep-control = <0>; + }; + ldo5_reg: regulator@8 { + regulator-compatible = "ldo5"; + reg = <8>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo6_reg: regulator@9 { + regulator-compatible = "ldo6"; + reg = <9>; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + ti,regulator-ext-sleep-control = <0>; + }; + ldo7_reg: regulator@10 { + regulator-compatible = "ldo7"; + reg = <10>; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + ti,regulator-ext-sleep-control = <1>; + }; + ldo8_reg: regulator@11 { + regulator-compatible = "ldo8"; + reg = <11>; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + ti,regulator-ext-sleep-control = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/twl-familly.txt b/Documentation/devicetree/bindings/mfd/twl-familly.txt new file mode 100644 index 000000000..a66fcf946 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl-familly.txt @@ -0,0 +1,47 @@ +Texas Instruments TWL family + +The TWLs are Integrated Power Management Chips. +Some version might contain much more analog function like +USB transceiver or Audio amplifier. +These chips are connected to an i2c bus. + + +Required properties: +- compatible : Must be "ti,twl4030"; + For Integrated power-management/audio CODEC device used in OMAP3 + based boards +- compatible : Must be "ti,twl6030"; + For Integrated power-management used in OMAP4 based boards +- interrupts : This i2c device has an IRQ line connected to the main SoC +- interrupt-controller : Since the twl support several interrupts internally, + it is considered as an interrupt controller cascaded to the SoC one. +- #interrupt-cells = <1>; +- interrupt-parent : The parent interrupt controller. + +Optional node: +- Child nodes contain in the twl. The twl family is made of several variants + that support a different number of features. + The children nodes will thus depend of the capability of the variant. + + +Example: +/* + * Integrated Power Management Chip + * http://www.ti.com/lit/ds/symlink/twl6030.pdf + */ +twl@48 { + compatible = "ti,twl6030"; + reg = <0x48>; + interrupts = <39>; /* IRQ_SYS_1N cascaded to gic */ + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + #address-cells = <1>; + #size-cells = <0>; + + twl_rtc { + compatible = "ti,twl_rtc"; + interrupts = <11>; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/twl4030-audio.txt b/Documentation/devicetree/bindings/mfd/twl4030-audio.txt new file mode 100644 index 000000000..414d2ae0a --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl4030-audio.txt @@ -0,0 +1,46 @@ +Texas Instruments TWL family (twl4030) audio module + +The audio module inside the TWL family consist of an audio codec and a vibra +driver. + +Required properties: +- compatible : must be "ti,twl4030-audio" + +Optional properties, nodes: + +Audio functionality: +- codec { }: Need to be present if the audio functionality is used. Within this + section the following options can be used: +- ti,digimic_delay: Delay need after enabling the digimic to reduce artifacts + from the start of the recorded sample (in ms) +-ti,ramp_delay_value: HS ramp delay configuration to reduce pop noise +-ti,hs_extmute: Use external mute for HS pop reduction +-ti,hs_extmute_gpio: Use external GPIO to control the external mute +-ti,offset_cncl_path: Offset cancellation path selection, refer to TRM for the + valid values. + +Vibra functionality +- ti,enable-vibra: Need to be set to <1> if the vibra functionality is used. if + missing or it is 0, the vibra functionality is disabled. + +Example: +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + + ti,enable-vibra = <1>; + + codec { + ti,ramp_delay_value = <3>; + }; + + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt new file mode 100644 index 000000000..3d1996331 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt @@ -0,0 +1,48 @@ +Texas Instruments TWL family (twl4030) reset and power management module + +The power management module inside the TWL family provides several facilities +to control the power resources, including power scripts. For now, the +binding only supports the complete shutdown of the system after poweroff. + +Required properties: +- compatible : must be one of the following + "ti,twl4030-power" + "ti,twl4030-power-reset" + "ti,twl4030-power-idle" + "ti,twl4030-power-idle-osc-off" + +The use of ti,twl4030-power-reset is recommended at least on +3530 that needs a special configuration for warm reset to work. + +When using ti,twl4030-power-idle, the TI recommended configuration +for idle modes is loaded to the tlw4030 PMIC. + +When using ti,twl4030-power-idle-osc-off, the TI recommended +configuration is used with the external oscillator being shut +down during off-idle. Note that this does not work on all boards +depending on how the external oscillator is wired. + +Optional properties: + +- ti,system-power-controller: This indicates that TWL4030 is the + power supply master of the system. With this flag, the chip will + initiate an ACTIVE-to-OFF or SLEEP-to-OFF transition when the + system poweroffs. + +- ti,use_poweroff: Deprecated name for ti,system-power-controller + +Example: +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_power: power { + compatible = "ti,twl4030-power"; + ti,use_poweroff; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/twl6040.txt b/Documentation/devicetree/bindings/mfd/twl6040.txt new file mode 100644 index 000000000..a41157b5d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl6040.txt @@ -0,0 +1,67 @@ +Texas Instruments TWL6040 family + +The TWL6040s are 8-channel high quality low-power audio codecs providing audio, +vibra and GPO functionality on OMAP4+ platforms. +They are connected ot the host processor via i2c for commands, McPDM for audio +data and commands. + +Required properties: +- compatible : "ti,twl6040" for twl6040, "ti,twl6041" for twl6041 +- reg: must be 0x4b for i2c address +- interrupts: twl6040 has one interrupt line connecteded to the main SoC +- interrupt-parent: The parent interrupt controller +- gpio-controller: +- #gpio-cells = <1>: twl6040 provides GPO lines. +- twl6040,audpwron-gpio: Power on GPIO line for the twl6040 + +- vio-supply: Regulator for the twl6040 VIO supply +- v2v1-supply: Regulator for the twl6040 V2V1 supply + +Optional properties, nodes: +- enable-active-high: To power on the twl6040 during boot. +- clocks: phandle to the clk32k clock provider +- clock-names: Must be "clk32k" + +Vibra functionality +Required properties: +- vddvibl-supply: Regulator for the left vibra motor +- vddvibr-supply: Regulator for the right vibra motor +- vibra { }: Configuration section for vibra parameters containing the following + properties: +- ti,vibldrv-res: Resistance parameter for left driver +- ti,vibrdrv-res: Resistance parameter for right driver +- ti,viblmotor-res: Resistance parameter for left motor +- ti,viblmotor-res: Resistance parameter for right motor + +Optional properties within vibra { } section: +- vddvibl_uV: If the vddvibl default voltage need to be changed +- vddvibr_uV: If the vddvibr default voltage need to be changed + +Example: +&i2c1 { + twl6040: twl@4b { + compatible = "ti,twl6040"; + + interrupts = <0 119 4>; + interrupt-parent = <&gic>; + twl6040,audpwron-gpio = <&gpio4 31 0>; + + vio-supply = <&v1v8>; + v2v1-supply = <&v2v1>; + enable-active-high; + + /* regulators for vibra motor */ + vddvibl-supply = <&vbat>; + vddvibr-supply = <&vbat>; + + vibra { + /* Vibra driver, motor resistance parameters */ + ti,vibldrv-res = <8>; + ti,vibrdrv-res = <3>; + ti,viblmotor-res = <10>; + ti,vibrmotor-res = <10>; + }; + }; +}; + +/include/ "twl6040.dtsi" |