diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci')
6 files changed, 281 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 64f2fff12..6c5322c55 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -31,7 +31,7 @@ Optional properties: Example configuration: - pcie: pcie@0xdffff000 { + pcie: pcie@dffff000 { compatible = "snps,dw-pcie"; reg = <0xdffff000 0x1000>, /* Controller registers */ <0xd0000000 0x2000>; /* PCI config space */ diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index 3be80c689..83aeb1f5a 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -4,8 +4,8 @@ This PCIe host controller is based on the Synopsis Designware PCIe IP and thus inherits all the common properties defined in designware-pcie.txt. Required properties: -- compatible: "fsl,imx6q-pcie" -- reg: base addresse and length of the pcie controller +- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie", "fsl,imx6qp-pcie" +- reg: base address and length of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. - interrupt-names: Must include the following entries: @@ -19,6 +19,20 @@ Optional properties: - fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20 - fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127 - fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127 +- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for + gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs + do not meet gen2 jitter requirements and thus for gen2 capability a gen2 + compliant clock generator should be used and configured. +- reset-gpio: Should specify the GPIO for controlling the PCI bus device reset + signal. It's not polarity aware and defaults to active-low reset sequence + (L=reset state, H=operation state). +- reset-gpio-active-high: If present then the reset sequence using the GPIO + specified in the "reset-gpio" property is reversed (H=reset state, + L=operation state). + +Additional required properties for imx6sx-pcie: +- clock names: Must include the following additional entries: + - "pcie_inbound_axi" Example: diff --git a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt index b721beacf..59c2f47aa 100644 --- a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt +++ b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt @@ -34,11 +34,11 @@ Hip05 Example (note that Hip06 is the same except compatible): ranges = <0x82000000 0 0x00000000 0x220 0x00000000 0 0x10000000>; num-lanes = <8>; port-id = <1>; - #interrupts-cells = <1>; - interrupts-map-mask = <0xf800 0 0 7>; - interrupts-map = <0x0 0 0 1 &mbigen_pcie 1 10 - 0x0 0 0 2 &mbigen_pcie 2 11 - 0x0 0 0 3 &mbigen_pcie 3 12 - 0x0 0 0 4 &mbigen_pcie 4 13>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0x0 0 0 1 &mbigen_pcie 1 10 + 0x0 0 0 2 &mbigen_pcie 2 11 + 0x0 0 0 3 &mbigen_pcie 3 12 + 0x0 0 0 4 &mbigen_pcie 4 13>; status = "ok"; }; diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 75321ae23..b8cc395ff 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -60,11 +60,14 @@ Required properties: - afi - pcie_x -Required properties on Tegra124 and later: +Required properties on Tegra124 and later (deprecated): - phys: Must contain an entry for each entry in phy-names. - phy-names: Must include the following entries: - pcie +These properties are deprecated in favour of per-lane PHYs define in each of +the root ports (see below). + Power supplies for Tegra20: - avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. - vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. @@ -122,11 +125,22 @@ Required properties: - Root port 0 uses 4 lanes, root port 1 is unused. - Both root ports use 2 lanes. -Example: +Required properties for Tegra124 and later: +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include an entry for each active lane. Note that the number + of entries does not have to (though usually will) be equal to the specified + number of lanes in the nvidia,num-lanes property. Entries are of the form + "pcie-N": where N ranges from 0 to the value specified in nvidia,num-lanes. + +Examples: +========= + +Tegra20: +-------- SoC DTSI: - pcie-controller { + pcie-controller@80003000 { compatible = "nvidia,tegra20-pcie"; device_type = "pci"; reg = <0x80003000 0x00000800 /* PADS registers */ @@ -186,10 +200,9 @@ SoC DTSI: }; }; - Board DTS: - pcie-controller { + pcie-controller@80003000 { status = "okay"; vdd-supply = <&pci_vdd_reg>; @@ -222,3 +235,204 @@ if a device on the PCI bus provides a non-probeable bus such as I2C or SPI, device nodes need to be added in order to allow the bus' children to be instantiated at the proper location in the operating system's device tree (as illustrated by the optional nodes in the example above). + +Tegra30: +-------- + +SoC DTSI: + + pcie-controller@00003000 { + compatible = "nvidia,tegra30-pcie"; + device_type = "pci"; + reg = <0x00003000 0x00000800 /* PADS registers */ + 0x00003800 0x00000200 /* AFI registers */ + 0x10000000 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH /* controller interrupt */ + GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x00000000 0x00000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x00001000 0x00001000 0 0x00001000 /* port 1 configuration space */ + 0x82000000 0 0x00004000 0x00004000 0 0x00001000 /* port 2 configuration space */ + 0x81000000 0 0 0x02000000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x20000000 0x20000000 0 0x08000000 /* non-prefetchable memory */ + 0xc2000000 0 0x28000000 0x28000000 0 0x18000000>; /* prefetchable memory */ + + clocks = <&tegra_car TEGRA30_CLK_PCIE>, + <&tegra_car TEGRA30_CLK_AFI>, + <&tegra_car TEGRA30_CLK_PLL_E>, + <&tegra_car TEGRA30_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x00000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x00001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x00004000 0 0x1000>; + reg = <0x001800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + }; + +Board DTS: + + pcie-controller@00003000 { + status = "okay"; + + avdd-pexa-supply = <&ldo1_reg>; + vdd-pexa-supply = <&ldo1_reg>; + avdd-pexb-supply = <&ldo1_reg>; + vdd-pexb-supply = <&ldo1_reg>; + avdd-pex-pll-supply = <&ldo1_reg>; + avdd-plle-supply = <&ldo1_reg>; + vddio-pex-ctl-supply = <&sys_3v3_reg>; + hvdd-pex-supply = <&sys_3v3_pexs_reg>; + + pci@1,0 { + status = "okay"; + }; + + pci@3,0 { + status = "okay"; + }; + }; + +Tegra124: +--------- + +SoC DTSI: + + pcie-controller@01003000 { + compatible = "nvidia,tegra124-pcie"; + device_type = "pci"; + reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ + 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ + 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ + + clocks = <&tegra_car TEGRA124_CLK_PCIE>, + <&tegra_car TEGRA124_CLK_AFI>, + <&tegra_car TEGRA124_CLK_PLL_E>, + <&tegra_car TEGRA124_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie-controller@01003000 { + status = "okay"; + + avddio-pex-supply = <&vdd_1v05_run>; + dvddio-pex-supply = <&vdd_1v05_run>; + avdd-pex-pll-supply = <&vdd_1v05_run>; + hvdd-pex-supply = <&vdd_3v3_lp0>; + hvdd-pex-pll-e-supply = <&vdd_3v3_lp0>; + vddio-pex-ctl-supply = <&vdd_3v3_lp0>; + avdd-pll-erefe-supply = <&avdd_1v05_run>; + + /* Mini PCIe */ + pci@1,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; + phy-names = "pcie-0"; + status = "okay"; + }; + + /* Gigabit Ethernet */ + pci@2,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>; + phy-names = "pcie-0"; + status = "okay"; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-armada8k.txt b/Documentation/devicetree/bindings/pci/pci-armada8k.txt new file mode 100644 index 000000000..598533a57 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-armada8k.txt @@ -0,0 +1,38 @@ +* Marvell Armada 7K/8K PCIe interface + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "marvell,armada8k-pcie" +- reg: must contain two register regions + - the control register region + - the config space region +- reg-names: + - "ctrl" for the control register region + - "config" for the config space region +- interrupts: Interrupt specifier for the PCIe controler +- clocks: reference to the PCIe controller clock + +Example: + + pcie@f2600000 { + compatible = "marvell,armada8k-pcie", "snps,dw-pcie"; + reg = <0 0xf2600000 0 0x10000>, <0 0xf6f00000 0 0x80000>; + reg-names = "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + dma-coherent; + + bus-range = <0 0xff>; + ranges = <0x81000000 0 0xf9000000 0 0xf9000000 0 0x10000 /* downstream I/O */ + 0x82000000 0 0xf6000000 0 0xf6000000 0 0xf00000>; /* non-prefetchable memory */ + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <1>; + clocks = <&cpm_syscon0 1 13>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt index 54eae2938..d08a4d511 100644 --- a/Documentation/devicetree/bindings/pci/pci-keystone.txt +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -56,6 +56,7 @@ Optional properties:- phy-names: name of the Generic Keystine SerDes phy for PCI - If boot loader already does PCI link establishment, then phys and phy-names shouldn't be present. + interrupts: platform interrupt for error interrupts. Designware DT Properties not applicable for Keystone PCI |